This patch cleans up few redundant parameters keeping
the same functionality intact.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Enable hotplug interrupts and move the hotplug scheduling into the
interrupt handler. This allows us to introduce a screen at any time
while we're running.
[jg1.han@samsung.com: moved the bit masking of hotplug interrupts]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Move the hotplug related code from probe and resume into a workqueue.
This allows us to initialize the DP driver (and resume it) when there
is no monitor connected.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
This patch enables device tree based discovery support for DP driver.
The driver is modified to handle platform data in both the cases:
with DT and non-DT.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
This patch changes return type of exynos_dp_init_video to void,
because the return value is unnecessary.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Fix the return value of exynos_dp_get_pll_lock_status to
reflect what it actually returns.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Olof Johansson <olofj@chromium.org>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds adjustement for voltage swing and pre-emphasis during
Link Training procedure. According to the DP specification, unless all
the LANEx_CR_DONE bits are set, the transmitter must read
the ADJUST_REQUEST_LANEx_x, increase the voltage swing according to
the request, and update the TRAINING_LANEx_SET bytes to match the new
voltage swing setting.
Refer to the DP specification v1.1a, Section 3.5.1.3 Link Training.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Some functions are declared twice in header file; thus, these
declarations are unnecessary.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The sw reset should be called prioir to enabling sw defined function,
according to datasheet.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The devm_ functions allocate memory that is released when a driver
detaches. This makes the code smaller and a bit simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds analog and pll control setting. This control setting
is used for DP TX PHY block to set the values as below. It is beneficial
to improve analog characteristics.
- TX terminal registor is 50 Ohm.
- Reference clock of PHY is 24 MHz.
- Power source for TX digital logic is 1.0625 V.
- Power source for internal clock driver is 1.0625 V.
- PLL VCO range setting is 600 uA.
- Power down ring osc is turned off.
- AUX terminal resistor is 50 Ohm.
- AUX channel current is 8 mA and multiplied by 2.
- TX channel output amplitude is 400 mV.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Samsung EXYNOS SoC such Exynos5 has DP controller and embedded DP
panel can be used. This patch supports DP driver based on Samsung
EXYNOS SoC chip.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Ajay Kumar