commit bb8175a8aa ("mmc: sdhci: clarify DDR timing mode between
SD-UHS and eMMC") added MMC_DDR52 as eMMC's DDR mode to be
distinguished from SD-UHS, but it missed setting driver type for
MMC_DDR52 timing mode.
So sometimes we get the following error on Marvell BG2Q DMP board:
[ 1.559598] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd
response 0x900, card status 0xb00
[ 1.569314] mmcblk0: retrying using single block read
[ 1.575676] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd
response 0x900, card status 0x0
[ 1.585202] blk_update_request: I/O error, dev mmcblk0, sector 2
[ 1.591818] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd
response 0x900, card status 0x0
[ 1.601341] blk_update_request: I/O error, dev mmcblk0, sector 3
This patches fixes this by adding the missing driver type setting.
Fixes: bb8175a8aa ("mmc: sdhci: clarify DDR timing mode ...")
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently one mrq->data maybe execute dma_map_sg() twice
when mmc subsystem prepare over one new request, and the
following log show up:
sdhci[sdhci_pre_dma_transfer] invalid cookie: 24, next-cookie 25
In this condition, mrq->date map a dma-memory(1) in sdhci_pre_req
for the first time, and map another dma-memory(2) in sdhci_prepare_data
for the second time. But driver only unmap the dma-memory(2), and
dma-memory(1) never unmapped, which cause the dma memory leak issue.
This patch use another method to map the dma memory for the mrq->data
which can fix this dma memory leak issue.
Fixes: 348487cb28 ("mmc: sdhci: use pipeline mmc requests to improve performance")
Reported-and-tested-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In programmable mode, if the clock frequency is too high, the divider
can be too small to meet the clock frequency requirement especially to
init the SD card. In this case, switch to the divided clock mode.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Controller could have both NO_CARD_NO_RESET and BROKEN_CARD_DETECTION
quirks set. Use sdhci_do_get_cd() when applying NO_CARD_NO_RESET, which
properly check for BROKEN_CARD_DETECTION quirk.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no reason to use polling for card detection state change when
drivers are using dedicated GPIO for this. Don't poll in this case.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Controller could have BROKEN_CARD_DETECTION quirk set, but drivers
could use GPIO to detect card present state. Let, when defined, GPIO
take precedence, so drivers could properly detect card state and not
use polling.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
adds quirk for controllers whose clock divider zero is broken,
sdhci_set_clock function will incorporate this modification.
Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Device tree provides option to specify the max freqency with property
"max-frequency" in dts and common parse function mmc_of_parse() will
parse it and use this value to set host->f_max to tell the MMC core
the maxinum frequency the host works.
However, current sdhci driver will finally overwrite this value with
host->max_clk regardless of the max-frequency property.
This patch makes sure not overwrite the max-frequency set from device
tree and do basic sanity check.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We should not call dma_free_coherent if host->adma_table is NULL,
otherwise may trigger panic.
Fixes: d1e49f77d7 ("mmc: sdhci: convert ADMA descriptors to a...")
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When dma mapping (dma_map_sg) fails in sdhci_pre_dma_transfer, -EINVAL
is returned. There are 3 callers of sdhci_pre_dma_transfer:
* sdhci_pre_req and sdhci_adma_table_pre: handle negative return
* sdhci_prepare_data: handles 0 (error) and "else" (good) only
sdhci_prepare_data is therefore broken. When it receives -EINVAL from
sdhci_pre_dma_transfer, it assumes 1 sg mapping was mapped. Later,
this non-existent mapping with address 0 is kmap'ped and written to:
Corrupted low memory at ffff880000001000 (1000 phys) = 22b7d67df2f6d1cf
Corrupted low memory at ffff880000001008 (1008 phys) = 63848a5216b7dd95
Corrupted low memory at ffff880000001010 (1010 phys) = 330eb7ddef39e427
Corrupted low memory at ffff880000001018 (1018 phys) = 8017ac7295039bda
Corrupted low memory at ffff880000001020 (1020 phys) = 8ce039eac119074f
...
So teach sdhci_prepare_data to understand negative return values from
sdhci_pre_dma_transfer and disable DMA in that case, as well as for
zero.
It was introduced in 348487cb28 (mmc:
sdhci: use pipeline mmc requests to improve performance). The commit
seems to be suspicious also by assigning host->sg_count both in
sdhci_pre_dma_transfer and sdhci_adma_table_pre.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable@vger.kernel.org # 4.0+
Fixes: 348487cb28
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 3a48edc4bd ("mmc: sdhci: Use mmc core regulator infrastucture")
changed the behavior for how to assign the ocr_avail mask for the mmc
host. More precisely it started to mask the bits instead of assigning
them.
Restore the behavior, but also make it clear that an OCR mask created
from an external regulator overrides the other ones. The OCR mask is
determined by one of the following with this priority:
1. Supported ranges of external regulator if one supplies VDD
2. Host OCR mask if set by the driver (based on DT properties)
3. The capabilities reported by the controller itself
Fixes: 3a48edc4bd ("mmc: sdhci: Use mmc core regulator infrastucture")
Cc: Tim Kryger <tim.kryger@gmail.com>
Reported-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@gmail.com>
Add a callbak to let host drivers select drive
strength.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_do_set_ios() doesn't currently program SDHCI_HOST_CONTROL2
register correctly when host->preset_enabled == false.
Add code to handle the missing cases MMC_SET_DRIVER_TYPE_B and
MMC_SET_DRIVER_TYPE_D.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use BUG_ON() instead of an 'if' condition followed by BUG().
The semantic patch that makes this change is available
in scripts/coccinelle/misc/bugon.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make use of mmc core support for re-tuning instead
of doing it all in the sdhci driver.
This patch also changes to flag the need for re-tuning
always after runtime suspend when tuning has been used
at initialization. Previously it was only done if
the re-tuning timer was in use.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_request function should consider a non-removable device
always present.
Call the correct logic already available in sdhci_do_get_cd function.
This fixes some logic paths where MMC requests are being made to
non-removable devices that do not have the card detect pin connected
on the hardware as it is non-removable.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For CMD53 in block mode, the host does not need to stop the transfer,
as it stops when the block count (present in CMD53) is reached.
Signed-off-by: Corneliu Doban <cdoban@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add quirk to handle broken auto-CMD23.
Some controllers do not respond after the first auto-CMD23 is issued.
This allows CMD23 to still work (mandatory for the faster UHS-I mode)
rather than disabling CMD23 entirely via SDHCI_QUIRK2_HOST_NO_CMD23.
Signed-off by: Corneliu Doban <cdoban@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I observed the Host Control2 register isn't correctly restored
after runtime resuming on BG2Q. For example, the register reads
as 0x800c before runtime suspend, but it's set as 0x8004 after runtime
resuming. This could results in a non working host.
The reason is the Host Control2 is incorrectly reset when switching
voltage. We fix this by following the same sequence during initialization.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch defines a quirk to disable the block count
for single block transactions.
It is a preparation and will be used by Fujitsu
SDHCI controller f_sdh30 driver.
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch defines a quirk for tuning work
around for some sdhci host controller. It sets
both SDHCI_CTRL_EXEC_TUNING and SDHCI_CTRL_TUNED_CLK
for tuning.
It is a preparation and will be used by Fujitsu
SDHCI controller f_sdh30 driver.
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a callback function to do
controller-specific actions when switching voltages.
It is a preparation and will be used by Fujitsu
SDHCI controller f_sdh30 driver.
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch solves the coding style issue by adding a space
before (
Signed-off-by: Mohammad Jamal <md.jamalmohiuddin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no point making the initialization
of buf_ready_int conditional on host version.
Simplify by just doing it always. Note that
the other conditional initializations will be
removed when the new way of doing re-tuning
is taken into use.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is based on the patches by Per Forlin, Tony Lin and Ryan QIAN.
This patch complete the API 'post_req' and 'pre_req' in sdhci host side,
Test Env:
1. i.MX6Q-SABREAUTO board, CPU @ 996MHz, use ADMA in uSDHC controller.
2. Test command:
$ echo 1 > /proc/sys/vm/drop_caches
write to sd card:
$ dd if=/dev/zero of=/dev/mmcblk0 bs=1M count=2000 conv=fsync
read the sd card:
$ dd if=/dev/mmcblk0 of=/dev/null bs=1M count=2000
3. TOSHIBA 16GB SD3.0 card, running at 4 bit, SDR104 @ 198MHZ
Performance with and without this patch:
-------------------------------------------------
| | read speed | write speed |
|------------------------------------------------
| with this patch | ~76.7 MB/s | ~23.3 MB/s |
|------------------------------------------------
|without this patch | ~60.5 MB/s | ~22.5 MB/s |
-------------------------------------------------
4. SanDisk 8GB SD3.0 card, running at 4 bit, DDR50 @ 50MHZ
Performance with and without this patch:
-------------------------------------------------
| | read speed | write speed |
|------------------------------------------------
| with this patch | ~40.5 MB/s | ~15.6 MB/s |
|------------------------------------------------
|without this patch | ~36.1 MB/s | ~14.1 MB/s |
-------------------------------------------------
5. Kingston 8GB SD2.0 card, running at 4 bit, High-speed @ 50MHZ
Performance with and without this patch:
-------------------------------------------------
| | read speed | write speed |
|------------------------------------------------
| with this patch | ~22.7 MB/s | ~8.2 MB/s |
|------------------------------------------------
|without this patch | ~21.3 MB/s | ~8.0 MB/s |
-------------------------------------------------
6. About eMMC, Sandisk 8GB eMMC on i.MX6DL-sabresd board, CPU @ 792MHZ,
eMMC running at 8 bit, DDR52 @ 52MHZ.
Performance with and without this patch:
-------------------------------------------------
| | read speed | write speed |
|------------------------------------------------
| with this patch | ~37.3 MB/s | ~10.5 MB/s |
|------------------------------------------------
|without this patch | ~33.4 MB/s | ~10.5 MB/s |
-------------------------------------------------
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bounce buffer, used for misaligned bytes for ADMA access,
resides wholly within the (align_sz)-aligned word, just by construction.
The page addresses are aligned to (align_sz), either for 4 or 8 bytes
alignment, so that the aligned word resides wholly within a single page
and can't cross the page boundary. So, the bounce buffer can't cross
the page boundary too. That's why the warnings are never hit, and can
be safely removed.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Host controllers lacking the required internal vmmc regulator may still
follow the spec with regard to the LSB of SDHCI_POWER_CONTROL. Set the
SDHCI_POWER_ON bit when vmmc is enabled to encourage the controller to
to drive CMD, DAT, SDCLK.
This fixes a regression observed on some Qualcomm and Nvidia boards
caused by 5222161 mmc: sdhci: Improve external VDD regulator support.
Fixes: 52221610dd (mmc: sdhci: Improve external VDD regulator support)
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Tested-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sleep in atomic context happened on Trats2 board after inserting or
removing SD card because mmc_gpio_get_cd() was called under spin lock.
Fix this by moving card detection earlier, before acquiring spin lock.
The mmc_gpio_get_cd() call does not have to be protected by spin lock
because it does not access any sdhci internal data.
The sdhci_do_get_cd() call access host flags (SDHCI_DEVICE_DEAD). After
moving it out side of spin lock it could theoretically race with driver
removal but still there is no actual protection against manual card
eject.
Dmesg after inserting SD card:
[ 41.663414] BUG: sleeping function called from invalid context at drivers/gpio/gpiolib.c:1511
[ 41.670469] in_atomic(): 1, irqs_disabled(): 128, pid: 30, name: kworker/u8:1
[ 41.677580] INFO: lockdep is turned off.
[ 41.681486] irq event stamp: 61972
[ 41.684872] hardirqs last enabled at (61971): [<c0490ee0>] _raw_spin_unlock_irq+0x24/0x5c
[ 41.693118] hardirqs last disabled at (61972): [<c04907ac>] _raw_spin_lock_irq+0x18/0x54
[ 41.701190] softirqs last enabled at (61648): [<c0026fd4>] __do_softirq+0x234/0x2c8
[ 41.708914] softirqs last disabled at (61631): [<c00273a0>] irq_exit+0xd0/0x114
[ 41.716206] Preemption disabled at:[< (null)>] (null)
[ 41.721500]
[ 41.722985] CPU: 3 PID: 30 Comm: kworker/u8:1 Tainted: G W 3.18.0-rc5-next-20141121 #883
[ 41.732111] Workqueue: kmmcd mmc_rescan
[ 41.735945] [<c0014d2c>] (unwind_backtrace) from [<c0011c80>] (show_stack+0x10/0x14)
[ 41.743661] [<c0011c80>] (show_stack) from [<c0489d14>] (dump_stack+0x70/0xbc)
[ 41.750867] [<c0489d14>] (dump_stack) from [<c0228b74>] (gpiod_get_raw_value_cansleep+0x18/0x30)
[ 41.759628] [<c0228b74>] (gpiod_get_raw_value_cansleep) from [<c03646e8>] (mmc_gpio_get_cd+0x38/0x58)
[ 41.768821] [<c03646e8>] (mmc_gpio_get_cd) from [<c036d378>] (sdhci_request+0x50/0x1a4)
[ 41.776808] [<c036d378>] (sdhci_request) from [<c0357934>] (mmc_start_request+0x138/0x268)
[ 41.785051] [<c0357934>] (mmc_start_request) from [<c0357cc8>] (mmc_wait_for_req+0x58/0x1a0)
[ 41.793469] [<c0357cc8>] (mmc_wait_for_req) from [<c0357e68>] (mmc_wait_for_cmd+0x58/0x78)
[ 41.801714] [<c0357e68>] (mmc_wait_for_cmd) from [<c0361c00>] (mmc_io_rw_direct_host+0x98/0x124)
[ 41.810480] [<c0361c00>] (mmc_io_rw_direct_host) from [<c03620f8>] (sdio_reset+0x2c/0x64)
[ 41.818641] [<c03620f8>] (sdio_reset) from [<c035a3d8>] (mmc_rescan+0x254/0x2e4)
[ 41.826028] [<c035a3d8>] (mmc_rescan) from [<c003a0e0>] (process_one_work+0x180/0x3f4)
[ 41.833920] [<c003a0e0>] (process_one_work) from [<c003a3bc>] (worker_thread+0x34/0x4b0)
[ 41.841991] [<c003a3bc>] (worker_thread) from [<c003fed8>] (kthread+0xe4/0x104)
[ 41.849285] [<c003fed8>] (kthread) from [<c000f268>] (ret_from_fork+0x14/0x2c)
[ 42.038276] mmc0: new high speed SDHC card at address 1234
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 94144a465d ("mmc: sdhci: add get_cd() implementation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Re-tuning for HS400 mode must be done in HS200
mode. Currently there is no support for that.
That needs to be reflected in the code.
Specifically, if tuning is executed in HS400 mode
then return an error, and do not start the
tuning timer if HS200 tuning is being done prior
to switching to HS400.
Note that periodic re-tuning is not expected
to be needed for HS400 but re-tuning is still
needed after the host controller has lost power.
In the case of suspend/resume that is not necessary
because the card is fully re-initialised. That
just leaves runtime suspend/resume with no support
for HS400 re-tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The tuning timer is always used if the tuning mode
is 1 and there is a tuning count, irrespective of
whether this is the first call, or any subsequent
call. Consequently the logic to start the timer
can be simplified.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A 'goto' can be used to save duplicating unlocking
and returning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Re-tuning requires that the maximum data length
is limited to 4MiB. The code currently changes
max_blk_count in an attempt to achieve that.
This is wrong because max_blk_count is a different
limit, but it is also un-necessary because
max_req_size is 512KiB anyway. Consequently, the
changes to max_blk_count are removed and the
comment for max_req_size adjusted accordingly.
The comment is also tweaked to show that the 512KiB
limit is a SDMA limit not an ADMA limit.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/mmc/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC core already has support for HS400. Add HS400
support to SDHCI driver. The SDHC Standard specification
does not define HS400 so consequently HS400 support is
non-standard. However HS400 is not selected without
the host controller setting the corresponding capability
flags so host controllers not yet supporting HS400
will not be affected. To support that, a quirk
SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400 is introduced to
enable the use of capabilities register reserved bit-63
to indicate HS400 support.
Because HS400 is non-standard for SDHCI, it is possible
that different vendors will do things in different ways.
However HS200 support faced the same issue but currently
there is only one solution. As such, no attempt has
been made to provide for alternate HS400 solutions except
for SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
1.2V HS200 mode capability is cleared if there is not a voltage
regulator that supports 1.2V. Do the same for 1.2V HS400 mode.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
supply.vqmmc is used with the IS_ERR macro which means
the value must be valid or an error code. NULL is
neither, so replace with ERR_PTR(-EINVAL).
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHC controller in AMD chipsets require SDHC transfer mode
register to be cleared for commands without data. The issue was
uncovered during testing eMMC cards on KB/ML based platforms
Signed-off-by: Vincent Wan <vincent.wan@amd.com>
Signed-off-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Tested-by: Vikram B <vikram.b@amd.com>
Tested-by: Raghavendra Swamy <raghavendra.swamy@amd.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add 64-bit ADMA support including:
- add 64-bit ADMA descriptor
- add SDHCI_USE_64_BIT_DMA flag
- set upper 32-bits of DMA addresses
- ability to select 64-bit ADMA
- ability to use 64-bit ADMA sizes and alignment
- display "ADMA 64-bit" when host is added
It is assumed that a 64-bit capable device has set a 64-bit DMA mask
and *must* do 64-bit DMA. A driver has the opportunity to change
that during the first call to ->enable_dma(). Similarly
SDHCI_QUIRK2_BROKEN_64_BIT_DMA must be left to the drivers to
implement.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Define the ADMA descriptor structure instead of
using manual offsets and casts.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Define all the ADMA constants instead of having numbers
scattered throughout the code.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Define the maximum number of segments instead of
having the constant 128 appearing in the code in
various places.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for 64-bit ADMA, parameterize ADMA sizes
and alignment. 64-bit ADMA has a larger descriptor
because it contains a 64-bit address instead of a 32-bit
address. Also data must be 8-byte aligned instead
of 4-byte aligned. Consequently, sdhci_host members
are added for descriptor, table, and buffer sizes
and alignment.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is kernel-style to use 'void *' for anonymous data.
This is being applied to the ADMA bounce buffer which
contains unaligned bytes, and to the ADMA descriptor
table which will contain 32-bit ADMA descriptors
or 64-bit ADMA descriptors when support is added.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for 64-bit ADMA, separate out code
that touches the ADMA descriptor by adding
sdhci_adma_mark_end().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for 64-bit ADMA, rename adma_desc to
adma_table. That is because members will be added
for descriptor size and table size, so using adma_desc
(which is the table) is confusing.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rename sdhci_set_adma_desc to sdhci_adma_write_desc and
sdhci_show_adma_error to sdhci_adma_show_error so that
all ADMA functions start with sdhci_adma_.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The intent of the warning is to warn if the ADMA table
overflows. However there can be one more 'end' entry
so the condition should be adjusted accordingly.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bytes are being copied from/to a single page. The intent
of the warning is to warn if the page boundary is crossed.
There are two problems. First, PAGE_MASK is mistaken for
(PAGE_SIZE - 1). Secondly, instead of using the number
of bytes to copy, the warning is using the maximum that
that value could be. Fix both.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ADMA2 descriptor table size was being calculated incorrectly
Fix it.
Note that it has been wrong for a long time and likely has not
caused any problems because of a combination of 1) not needing
alignment descriptors for block operations 2) more memory being
allocated than was requested 3) the use of
SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC which does not use an extra
descriptor for the end marker.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jisheng Zhang