When KDUMP is triggered the driver first talks to the firmware in INTX
mode, but the adapter firmware is still in MSIX mode. Therefore the first
driver command hangs since the driver is waiting for an INTX response and
firmware gives a MSIX response. If when the OS is installed on a RAID
drive created by the adapter KDUMP will hang since the driver does not
receive a response in sync mode.
Fixed by: Change the firmware to INTX mode if it is in MSIX mode before
sending the first sync command.
Cc: stable@vger.kernel.org
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As the firmware for series 6, 7, 8 cards does not support msi, remove it
in the driver
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Suggested-by: Seymour, Shane M <shane.seymour@hpe.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
while driver removal is in progress or PCI shutdown is invoked, driver
kills AIF aacraid thread, but IOCTL requests from the management tools
re-start AIF thread leading to IOP_RESET.
Fixed by setting adapter_shutdown flag when PCI shutdown is invoked.
Signed-off-by: Raghava Aditya Renukunta <raghavaaditya.renukunta@pmcs.com>
Reviewed-by: Shane Seymour <shane.seymour@hpe.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If writeq() not supported, then do atomic two 32bit write
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Reviewed-by: Karthikeya Sunkesula <Karthikeya.Sunkesula@pmcs.com>
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
After getting the platform shutdown command "VM_CloseAll" response from the
firmware, driver was getting configuration IOCTL request from the upper layers
and it sends down to firmware. This causes firmware assert issue.
This patch fixes the firmware assert issue. During the shutdown, if driver
gets commands from the upper layer, driver sends error code to the upper
layers.
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This patch fixes the IOP_RESET issue. Sending IOP_RESET command need to wait
for only 10 sec instead of 5 minutes in case of firmware does not response
IOP_RESET command. Disable interrupt before setup interrupt routine to
prevent spurious interrupts.
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This patch adds dual flash firmware support for Series 7 and above controllers.
[thenzl: used ssleep(10) instead udelay]
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Series 7 Async. (performance) mode support added
- New scatter/gather list format for Series 7
- Driver converts s/g list to a firmware suitable list for best performance on
Series 7, this can be disabled with driver parameter "aac_convert_sgl" for
testing purposes
- New container read/write command structure for Series 7
- Fast response support for the SCSI pass-through path added
- Async. status response buffer changes
Signed-off-by: Mahesh Rajashekhara <Mahesh_Rajashekhara@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This may not fix all endian issues in this driver, but it does get the
driver working on PowerPC for a PMC SRC card. So it should at least fix
all the problems in the core and in the SRC support.
[jejb: fix >> 32 breakage reported by Fengguang Wu]
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Acked-by: Achim Leubner <Achim_Leubner@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added Sync. mode to support Series 7/8/9 controller families: This is a
compatibility mode for all these controller families. The Async. (Performance)
mode can be changed in the future. First Async. mode version added for Series
7; Controller parameter aac_sync_mode added
Signed-off-by: Mahesh Rajashekhara <aacraid@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added new hardware device 0x28b interface for PMC-Sierra's SRC based
controller family.
- new src.c file for 0x28b specific functions
- new XPORT header required
- sync. command interface: doorbell bits shifted (SRC_ODR_SHIFT, SRC_IDR_SHIFT)
- async. Interface: different inbound queue handling, no outbound I2O
queue available, using doorbell ("PmDoorBellResponseSent") and
response buffer on the host ("host_rrq") for status
- changed AIF (adapter initiated FIBs) interface: "DoorBellAifPending"
bit to inform about pending AIF, "AifRequest" command to read AIF,
"NoMoreAifDataAvailable" to mark the end of the AIFs
Signed-off-by: Mahesh Rajashekhara <aacraid@pmc-sierra.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
These particular problems were reported by Cisco and SAP and customers
as well. Cisco reported on RHEL4 U6 and SAP reported on SLES9 SP4 and
SLES10 SP2. We added these fixes on RHEL4 U6 and gave a private build
to IBM and Cisco. Cisco and IBM tested it for more than 15 days and
they reported that they did not see the issue so far. Before the fix,
Cisco used to see the issue within 5 days. We generated a patch for
SLES9 SP4 and SLES10 SP2 and submitted to Novell. Novell applied the
patch and gave a test build to SAP. SAP tested and reported that the
build is working properly.
We also tested in our lab using the tools "dishogsync", which is IO
stress tool and the tool was provided by Cisco.
Issue1: File System going into read-only mode
Root cause: The driver tends to not free the memory (FIB) when the
management request exits prematurely. The accumulation of such
un-freed memory causes the driver to fail to allocate anymore memory
(FIB) and hence return 0x70000 value to the upper layer, which puts
the file system into read only mode.
Fix details: The fix makes sure to free the memory (FIB) even if the
request exits prematurely hence ensuring the driver wouldn't run out
of memory (FIBs).
Issue2: False Raid Alert occurs
When the Physical Drives and Logical drives are reported as deleted or
added, even though there is no change done on the system
Root cause: Driver IOCTLs is signaled with EINTR while waiting on
response from the lower layers. Returning "EINTR" will never initiate
internal retry.
Fix details: The issue was fixed by replacing "EINTR" with
"ERESTARTSYS" for mid-layer retries.
Signed-off-by: Penchala Narasimha Reddy <ServeRAIDDriver@hcl.in>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
changes:
- set aac_cache=2 as default value to avoid performance problem
(Novell bugzilla #469922)
- Dell/PERC controller boot problem fixed (RedHat bugzilla #457552)
- WWN flag added to fix SLES10 SP1/SP2 drive detection problems
- 64-bit support changes
- DECLARE_PCI_DEVICE_TABLE macro added
- controller type changes
Signed-off-by: Achim Leubner <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For firmware that supports the feature(s), add the ability to start or
stop an array using the associated SCSI commands, to automatically
manage the spin-up of an array on new I/O reporting back the
appropriate check conditions and actions in cooperation with the
normal timeout mechanisms and enable the blackout period management in
the Firmware associated with the background spin-down of the arrays
when the Firmware times out and deems the arrays as idle.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Big endian systems issues discovered in the aacraid driver. Somewhat
reverses a patch from November 7th of last year that removed swap
operations because they formerly were being assigned to an u8 array
when they should have been assigned to an le32 array.
This patch is largely inert for any little endian processor
architecture. It resolves a bug in delivering the BlinkLED AIF event
to registered applications when the adapter or associated hardware was
reset due to ill health. A rare corner case occurrence, also largely
unnoticed by any as it was a new (untested!) feature.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use of ptrdiff_t in places like
- if (!access_ok(VERIFY_WRITE, u_tmp->rx_buf, u_tmp->len))
+ if (!access_ok(VERIFY_WRITE, (u8 __user *)
+ (ptrdiff_t) u_tmp->rx_buf,
+ u_tmp->len))
is wrong; for one thing, it's a bad C (it's what uintptr_t is for; in general
we are not even promised that ptrdiff_t is large enough to hold a pointer,
just enough to hold a difference between two pointers within the same object).
For another, it confuses the fsck out of sparse.
Use unsigned long or uintptr_t instead. There are several places misusing
ptrdiff_t; fixed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Inspired somewhat by Vignesh Babu <vignesh.babu@wipro.com> patch to
dpt_i2o.c to replace kmalloc/memset sequences with kzalloc, doing the
same for the aacraid driver.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Unsigned long is not always the same size as a pointer, namely on 32 bit
systems with 64 bit address space. Ptrdiff_t is the same size as a
pointer in all configurations. By using ptrdiff_t we can mitigate the
warning messages on these configurations. There should be no side
effects of this patch.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Received from Mark Salyzyn,
Replace all if/else communication transports with a platform function call.
This is in recognition of the need to migrate to up-and-coming transports.
Currently the Linux driver does not support two available communication
transports provided by our products, these will be added in future patches, and
will expand the platform function set.
Signed-off-by Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Received from Mark Salyzyn:
The only real difference between the rkt and rx platform modules is the
offset of the message registers. This patch recognizes this similarity
and simplifies the driver to reduce it's code footprint and to improve
maintainability by reducing the code duplication.
Visibly, the 'rkt.c' portion of this patch looks more complicated than
it really is. View it as retaining the rkt-only specifics of the
interface.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
The enclosed patch cleans up some code fragments, adds some paranoia
(unproven causes of potential driver failures).
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This may seem like a DILLIGAF, but after chatting with the F/W folks,
there is no harm in dropping the page calculation as denoted in the
enclosed patch for these older adapters in this new age of 4GB+ memory
sticks. Any resource optimization within the old-old-old adapters for
systems with less than 4G of memory is of little consequence. The
existing AAC_QUIRK_31BIT flag in linit.c should look after the rest of
the legacy hardware DMA limitations.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
Spelling correction, orphaned comment removal & update branch name.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received From Mark Salyzyn
The queue tracking is just not being used, not even for debugging. Information
about outstanding commands can be acquired from the scsi structures.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use the kthread_ API instead of opencoding lots of hairy code for kernel
thread creation and teardown.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Salyzyn, Mark <mark_salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn,
Reduce the possibility of namespace collision. Prefix with aac_.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn.
This patch adds the 'new comm' interface, which modern AAC based
adapters that are less than a year old support in the name of much
improved performance. These modern adapters support both the legacy and
the 'new comm' interfaces.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
The size of the command packet's scatter gather list maximum size was
miscalculated in the low range leading to the driver initialization
limiting the maximum i/o size that could go to the Adapter. There were
no negative operational side effects resulting from this bad math, only
a subtle limit in performance of the Adapter at the top end of the
range.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
In the rare instances where the adapter, or the motherboard, is
misbehaving; driver initialization or shutdown becomes problematic. By
introducing a 3 minute timeout on the first interrupt driven command
during initialization, or the issuance of the adapter shutdown command
during driver unload, we can resolve the lockup problems induced by
common (but rare) hardware misbehaviors.
The timeout during initialization, should it occur, is accompanied by a
message presented to the console and the logs indicating that the user
should inspect and resolve problems with interrupt routing.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
There are a few adapters that are capable of creating devices with this large
of a capacity, but now that we have the large fib support in, the management
applications will be capable of generating them. The problem is, once they are
created, the driver will not be able to access the devices correctly without
this patch.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec:
If more than two commands are outstanding to the controller, there is no
need to notify the adapter via a PCI bus transaction of additional
commands added into the queue; it will get to them when it works through
the produce/consumer indexes.
This reduced the PCI traffic in the driver to submit a command to the
queue to near zero allowing a significant number of commands to be
turned around with no need to block for the PCI bridge to flush the
notify request to the adapter.
Interrupt mitigation has always been present in the driver; it was
turned off because of a bug that prevented one from realizing the
usefulness of the feature. This bug is fixed in this patch.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New code from the Adaptec driver. Performance enhancement for newer
adapters. I hope that this isn't too big for a single patch. I believe
that other than the few small cleanups mentioned, that the changes are
all related.
- Added Variable FIB size negotiation for new adapters.
- Added support to maximize scatter gather tables and thus permit
requests larger than 64KB/each.
- Limit Scatter Gather to 34 elements for ROMB platforms.
- aac_printf is only enabled with AAC_QUIRK_34SG
- Large FIB ioctl support
- some minor cleanup
Passes sparse check.
I have tested it on x86 and ppc64 machines.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch addresses the sparse -Wbitwise warnings that Christoph wanted
me to eliminate. This mostly consisted of making data structure
elements of hardware associated structures the __le* equivalent.
Although there were a couple places where there was mixing of cpu and le
variable math. These changes have been tested on both an x86 and ppc
machine running bonnie++. The usage of the LE32_ALL_ONES macro has been
eliminated.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch makes some needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Raghava Aditya Renukunta