Attached is a small code style cleanup patch that resulted from my
skimming through the arch/x86_64/kernel/traps.c code to figure out what
went haywire.
Signed-off-by: Roberto Nibali <ratz@drugphish.ch>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We've always had the problem that arguments only did a prefix match,
which resulted e.g. in noapic and noapictimer getting confused.
Fix the early argument parsing code to always check that arguments are
whole words (except for those that take additional arguments of course)
I factored out the checking code for that while also makes the code
easier to maintain.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While the modular aspect of the respective i386 patch doesn't apply to
x86-64 (as the top level page directory entry is shared between modules
and the base kernel), handlers registered with register_die_notifier()
are still under similar constraints for touching ioremap()ed or
vmalloc()ed memory. The likelihood of this problem becoming visible is
of course significantly lower, as the assigned virtual addresses would
have to cross a 2**39 byte boundary. This is because the callback gets
invoked
(a) in the page fault path before the top level page table propagation
gets carried out (hence a fault to propagate the top level page table
entry/entries mapping to module's code/data would nest infinitly) and
(b) in the NMI path, where nested faults must absolutely not happen,
since otherwise the IRET from the nested fault re-enables NMIs,
potentially resulting in nested NMI occurences.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code waits for the GART to clear the TLB flush bit. Use cpu_relax
in this time to allow hypervisors to yield the CPU in this time.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The PM timer path through main_timer_handler doesn't need
the delay variable because it figures it out in a different way.
Don't try to read it from the PIT. With stopped PIT timer
it is even useless.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Minor cleanup to lend better for physical CPU hotplug.
Earlier way of using num_processors as index doesnt
fit if CPUs come and go. This makes the code little bit better
to read, and helps physical hotplug use the same functions as boot.
Reserving CPU0 for BSP is too late to be done in smp_prepare_boot_cpu().
Since logical assignments from MADT is already done via
setup_arch()->acpi_boot_init()->parse lapic
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Touching of the floating point state in a kernel debugger must be
NMI-safe, specifically math_state_restore() must be able to deal with
being called out of an NMI context. In order to do that reliably, the
context switch code must take care to not leave a window open where
the current task's TS_USEDFPU flag and CR0.TS could get out of sync.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For consistency and to have only a single place of definition, replace
set_debug() uses with set_debugreg(), and eliminate the definition of
thj former.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While AMD formally permits multi-byte execution breakpoints, Intel
disallows 8-byte as much as 2- or 4-byte ones.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix one place where the previous change of cpu_pda from being an array
to being a macro was not properly carried out.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove all trailing tabs and spaces. No other changes.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
include/linux/platform.h contained nothing that was actually used except
the default_idle() prototype, and is therefore removed by this patch.
This patch does the following with the platform specific default_idle()
functions on different architectures:
- remove the unused function:
- parisc
- sparc64
- make the needlessly global function static:
- arm
- h8300
- m68k
- m68knommu
- s390
- v850
- x86_64
- add a prototype in asm/system.h:
- cris
- i386
- ia64
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Patrick Mochel <mochel@digitalimplant.org>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While working on these patch set, I found several possible cleanup on x86-64
and ia64.
akpm: I stole this from Andi's queue.
Not only does it clean up bitops. It also unrelatedly changes the prototype
of pci_mmcfg_init() and removes its arch_initcall(). It seems that the wrong
two patches got joined together, but this is the one which has been tested.
This patch fixes the current x86_64 build error (the pci_mmcfg_init()
declaration in arch/i386/pci/pci.h disagrees with the definition in
arch/x86_64/pci/mmconfig.c)
This also means that x86_64's pci_mmcfg_init() gets called in the same (new)
manner as x86's: from arch/i386/pci/init.c:pci_access_init(), rather than via
initcall.
The bitops cleanups came along for free.
All this worked OK in -mm testing (since 2.6.16-rc4-mm1) because x86_64 was
tested with both patches applied.
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Con Kolivas <kernel@kolivas.org>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we stop allocating percpu memory for not-possible CPUs we must not touch
the percpu data for not-possible CPUs at all. The correct way of doing this
is to test cpu_possible() or to use for_each_cpu().
This patch is a kernel-wide sweep of all instances of NR_CPUS. I found very
few instances of this bug, if any. But the patch converts lots of open-coded
test to use the preferred helper macros.
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Christian Zankel <chris@zankel.net>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Jens Axboe <axboe@suse.de>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch from Pavel moves userland freeze signals handling into more logical
place. It now hits even with mysqld running.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use boot info to start early_printk() at the current row on VGA console, as
left by the boot loader.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Stas Sergeev <stsp@aknet.ru>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The history is that -mm kernels do not work for me for a few months
already. The things started from crashing somewhere after starting init,
and for the last month - no boot at all, just "Uncompressing... OK,
booting kernel", and silence. Early console didn't work too. With the
latest releases this degraded into an infinite stream of the "Unknown
interrupt or fault" messages. So today my patience ran out and I started
to think how can I collect at least some info for the bug-report. Attached
is the patch that allows to gather some valueable debug info on the problem
by making an early console more useable. I can't properly test the patch,
as the kernel still doesn't boot, so I'll explain it in details in a hope
someone else can justify the intrusive changes.
arch_hooks.h: added prototypes for setup_early_printk() and early_printk().
setup.c: killed wrong setup_early_printk() prototype. Moved
setup_early_printk() a bit earlier, as it was not "early enough" to cover
the bug I was fighting with.
early_printk.c: made it to start printing from the bottom of the screen,
otherwise the messages interfere with the ones of the boot-loader, so you
can't read them.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Cc: Andi Kleen <ak@muc.de>
Cc: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sam's tree includes a new check, which found that we're exporting strpbrk()
multiple times.
It seems that the convention is that this is exported from the arch files, so
reove the lib/string.c export.
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: David Howells <dhowells@redhat.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This variable is rarely written to. Mark the variable accordingly.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commit c33d4568ac.
Andrew Clayton and Hugh Dickins report that it's broken for them and
causes strange page table and slab corruption, and spontaneous reboots.
Let's get it right next time.
Cc: Andrew Clayton <andrew@rootshell.co.uk>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
EM64T CPUs have somewhat weird error reporting for non canonical RIPs in
SYSRET.
We can't handle any exceptions there because the exception handler would
end up running on the user stack which is unsafe.
To avoid problems any code that might end up with a user touched pt_regs
should return using int_ret_from_syscall. int_ret_from_syscall ends up
using IRET, which allows safe exceptions.
Cc: Ernie Petrides <petrides@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While testing kexec and kdump we hit problems where the new kernel would
freeze or instantly reboot. The easiest way to trigger it was to kexec a
kernel compiled for CONFIG_M586 on an athlon cpu. Compiling for CONFIG_MK7
instead would work fine.
The patch fixes a few problems with the kexec inline asm.
Signed-off-by: Chris Mason <mason@suse.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commit 13a229abc2.
Quoth Andi:
"After some consideration and feedback from various people it turns
out this wasn't that good an idea. It has some problems and needs
more work. Since it was only an optimization anyways it's best to
just back it out again for now."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The commit e2c0388866 added
setup_additional_cpus to setup.c but this is only defined if
CONFIG_HOTPLUG_CPU is set. This patch changes the #ifdef to reflect that.
Signed-off-by: Brian Magnuson <magnuson@rcn.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The previous experiment for using apicmaintimer on ATI systems didn't
work out very well. In particular laptops with C2/C3 support often
don't let it tick during idle, which makes it useless. There were also
some other bugs that made the apicmaintimer often not used at all.
I tried some other experiments - running timer over RTC and some other
things but they didn't really work well neither.
I rechecked the specs now and it turns out this simple change is
actually enough to avoid the double ticks on the ATI systems. We just
turn off IRQ 0 in the 8254 and only route it directly using the IO-APIC.
I tested it on a few ATI systems and it worked there. In fact it worked
on all chipsets (NVidia, Intel, AMD, ATI) I tried it on.
According to the ACPI spec routing should always work through the
IO-APIC so I think it's the correct thing to do anyways (and most of the
old gunk in check_timer should be thrown away for x86-64).
But for 2.6.16 it's best to do a fairly minimal change:
- Use the known to be working everywhere-but-ATI IRQ0 both over 8254
and IO-APIC setup everywhere
- Except on ATI disable IRQ0 in the 8254
- Remove the code to select apicmaintimer on ATI chipsets
- Add some boot options to allow to override this (just paranoia)
In 2.6.17 I hope to switch the default over to this for everybody.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SMP time selection originally ran after all CPUs were brought up because
it needed to know the number of CPUs to decide if it needs an MP safe
timer or not.
This is not needed anymore because we know present CPUs early.
This fixes a couple of problems:
- apicmaintimer didn't always work because it relied on state that was
set up time_init_gtod too late.
- The output for the used timer in early kernel log was misleading
because time_init_gtod could actually change it later. Now always
print the final timer choice
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It didn't set up the CPU possible map early enough, so the
option didn't actually work.
Noticed by Heiko Carstens
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[description from AK]
Old check for the IO-APIC watchdog during the timer check was wrong -
it obviously should only drop into this if the IO-APIC watchdog is used.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Big Unisys systems have multiple clusters too, but they have an
synchronized TSC.
I'm using the SMBIOS to check for vendor == IBM.
Cc: Chris McDermott <lcm@us.ibm.com>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In previous versions of pci-gart.c, no_iommu was used to determine if IOMMU was
disabled in the GART DMA mapping functions. This changed in 2.6.16 and now
gart_xxx() functions are only called if gart is enabled. Therefore, uses of
no_iommu in the GART code are no longer necessary and can be removed.
Also, it removes double deceleration of no_iommu and force_iommu in pci.h and
proto.h, by removing the deceleration in pci.h.
Lastly, end_pfn off by one error.
Tested (along with patch 1/2) on dual opteron with gart enabled, iommu=soft,
and iommu=off.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Commit 9c869edac5 moved the i386 topology.c
file. That change broke x86-64 compiles, as it uses the same file.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't print KERN_INFO in the middle of a printk line.
printk(KERN_INFO "OEM ID: %s ",str);
is just above this. This is already fixed up in i386 copy.
Signed-off-by: Martin J. Bligh <mbligh@google.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
But do it after everything else to risk less from recursive
crashes.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many laptops have problems with ticking the local APIC timer in C2/C3.
The code added earlier to use it by default on ATI didn't really work
for them. Don't enable it when the system supports C2/C3.
This doesn't fix the problem fully, but at least it's not worse than before.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This caused a sigreturn with bad argument on a preemptible kernel
to complain with
Debug: sleeping function called from invalid context at /home/lsrc/quilt/linux/include/linux/rwsem.h:43
in_atomic():0, irqs_disabled():1
Call Trace: {__might_sleep+190} {profile_task_exit+21}
{__do_exit+34} {do_wait+0}
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Along with that, also suppress the memory touching altogether when the
watchdog is not running, to eliminate needless crosstalk. Plus ad a call
to it to make things consistent (one could also consider removing the call
in enable_timer_nmi_watchdog()).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't touch the non DMA members in the sg list in dma_map_sg in the IOMMU
Some drivers (in particular ST) ran into problems because they reused the sg
lists after passing them to pci_map_sg(). The merging procedure in the K8
GART IOMMU corrupted the state. This patch changes it to only touch the dma*
entries during merging, but not the other fields. Approach suggested by Dave
Miller.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We found a problem with x86_64 kernels with preemption enabled, where
having multiple tasks doing ptrace singlesteps around the same time will
cause the system to 'oops'. The problem seems that a task can get
preempted out of the do_debug() processing while it is running on the
DEBUG_STACK stack. If another task on that same cpu then enters do_debug()
and uses the same per-cpu DEBUG_STACK stack, the previous preempted tasks's
stack contents can be corrupted, and the system will oops when the
preempted task is context switched back in again.
The typical oops looks like the following:
Unable to handle kernel paging request at ffffffffffffffae RIP: <ffffffff805452a1>{thread_return+34}
PGD 103027 PUD 102429067 PMD 0
Oops: 0002 [1] PREEMPT SMP
CPU 0
Modules linked in:
Pid: 3786, comm: ssdd Not tainted 2.6.15.2 #1
RIP: 0010:[<ffffffff805452a1>] <ffffffff805452a1>{thread_return+34}
RSP: 0018:ffffffff80824058 EFLAGS: 000136c2
RAX: ffff81017e12cea0 RBX: 0000000000000000 RCX: 00000000c0000100
RDX: 0000000000000000 RSI: ffff8100f7856e20 RDI: ffff81017e12cea0
RBP: 0000000000000046 R08: ffff8100f68a6000 R09: 0000000000000000
R10: 0000000000000000 R11: ffff81017e12cea0 R12: ffff81000c2d53e8
R13: ffff81017f5b3be8 R14: ffff81000c0036e0 R15: 000001056cbfc899
FS: 00002aaaaaad9b00(0000) GS:ffffffff80883800(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffffffffffffffae CR3: 00000000f6fcf000 CR4: 00000000000006e0
Process ssdd (pid: 3786, threadinfo ffff8100f68a6000, task ffff8100f7856e20)
Stack: ffffffff808240d8 ffffffff8012a84a ffff8100055f6c00 0000000000000020
0000000000000001 ffff81000c0036e0 ffffffff808240b8 0000000000000000
0000000000000000 0000000000000000
Call Trace: <#DB>
<ffffffff8012a84a>{try_to_wake_up+985}
<ffffffff8012c0d3>{kick_process+87}
<ffffffff8013b262>{signal_wake_up+48}
<ffffffff8013b5ce>{specific_send_sig_info+179}
<ffffffff80546abc>{_spin_unlock_irqrestore+27}
<ffffffff8013b67c>{force_sig_info+159}
<ffffffff801103a0>{do_debug+289} <ffffffff80110278>{sync_regs+103}
<ffffffff8010ed9a>{paranoid_userspace+35}
Unable to handle kernel paging request at 00007fffffb7d000 RIP: <ffffffff8010f2e4>{show_trace+465}
PGD f6f25067 PUD f6fcc067 PMD f6957067 PTE 0
Oops: 0000 [2] PREEMPT SMP
This patch disables preemptions for the task upon entry to do_debug(), before
interrupts are reenabled, and then disables preemption before exiting
do_debug(), after disabling interrupts. I've noticed that the task can be
preempted either at the end of an interrupt, or on the call to
force_sig_info() on the spin_unlock_irqrestore() processing. It might be
better to attempt to code a fix in entry.S around the code that calls
do_debug().
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[description from AK]
The IBM Summit 3 chipset doesn't implement the HPET timer replacement
option. Since the current Linux code relies on it use a mixed mode with
both PIT for the interrupt and HPET counters for the time keeping. That
was already implemented, but didn't work properly because it was still
using the last interrupt offset in HPET. This resulted in x460 not
booting. Fix this up by using the free running HPET counter.
Shouldn't affect any other machine because they either use full HPET mode
or no HPET at all.
TBD needs a similar 32bit fix.
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: Bob Picco <bob.picco@hp.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently, x86_64 and ia64 arches do not clear the corresponding bits in
the node's cpumask when a cpu goes down or cpu bring up is cancelled. This
is buggy since there are pieces of common code where the cpumask is checked
in the cpu down code path to decide on things (like in the slab down path).
PPC does the right thing, but x86_64 and ia64 don't (This was the reason
Sonny hit upon a slab bug during cpu offline on ppc and could not reproduce
on other arches). This patch fixes it for x86_64. I won't attempt ia64 as
I cannot test it.
Credit for spotting this should go to Alok.
(akpm: this was applied, then reverted. But it's OK now because we now use
for_each_cpu() in the right places).
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commit 10f4dc8b27.
Quoth Andi Kleen:
"Kiran decided that it makes the problem worse than it was before.
Fixing it fully requires more work which is too much for 2.6.16. So
please revert that commit for now."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains a printk reorder to remove the current problem of
displaying "PCI-DMA: Disabling IOMMU." and then "PCI-DMA: using GART
IOMMU" 20 lines later in dmesg.
It also constains a printk reorder in swiotlb to state swiotlb
enablement prior to describing the location of the bounce buffers, and a
printk reorder to state gart enablement prior to describing the
aperature.
Also constains a whitespace cleanup in arch/x86_64/kernel/setup.c
Tested (along with patch 2/2) on dual opteron with gart enabled,
iommu=soft, and iommu=off.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hack for 2.6.16. In 2.6.17 all code that uses NR_CPUs should
be audited and changed to only touch possible CPUs.
Don't mark the reference per cpu data init data (so it stays
around after boot) and point all impossible CPUs to it. This way
they reference some valid - although shared memory. Usually
this is only initialization like INIT_LIST_HEADs and there
won't be races because these CPUs never run. Still somewhat hackish.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Roberto Nibali