Instead of switching capture mode depending on how many buffers are
available use a scratch buffer and always run in continuous mode. By
using a scratch buffer the responsiveness of the capture loop is
increased as it can keep running even if there are no buffers available
from userspace.
As soon as a userspace queues a buffer it is inserted into the capture
loop and returned as soon as it is filled. This is a improvement on the
previous logic where the whole capture loop was stopped and switched to
single capture mode if userspace did not feed the VIN driver buffers at
the same time it consumed them. To make matters worse it was difficult
for the driver to reenter continuous mode if it entered single mode even
if userspace started to queue buffers faster. This resulted in
suboptimal performance where if userspace where delayed for a short
period the ongoing capture would be slowed down and run in single mode
until the capturing process where restarted.
An additional effect of this change is that the capture logic can be
made much simple as we know that continuous mode will always be used.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Before starting a capture, allocate a scratch buffer which can be used
by the driver to give to the hardware if no buffers are available from
userspace. The buffer is not used in this patch but prepares for future
refactoring where the scratch buffer can be used to avoid the need to
fallback on single capture mode if userspace can't queue buffers as fast
as the VIN driver consumes them.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The V4L2_ASYNC_MATCH_FWNODE match criteria requires just one
struct to be filled (struct fwnode_handle). The V4L2_ASYNC_MATCH_DEVNAME
match criteria requires just a device name.
So, it doesn't make sense to enclose those into structs,
as the criteria can go directly into the union.
That makes easier to document it, as we don't need to document
weird senseless structs.
At drivers, this makes even clearer about the match criteria.
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Hyun Kwon <hyun.kwon@xilinx.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The async subdev notifier .bound(), .unbind() and .complete() operations
are function pointers stored directly in the v4l2_async_subdev
structure. As the structure isn't immutable, this creates a potential
security risk as the function pointers are mutable.
To fix this, move the function pointers to a new
v4l2_async_subdev_operations structure that can be made const in
drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of using a custom driver implementation, use
v4l2_async_notifier_parse_fwnode_endpoints() to parse the fwnode endpoints
of the device.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the requested pixelformat is not supported fallback to the default
format, do not revert the entire format.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The return value of __rvin_try_format_source is not checked, add a check
and propagate the error.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is only one subdevice registered with the async framework so there
is no need for the driver to check which subdevice is bound or unbound.
Remove these checks since the async framework preforms this.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[hans.verkuil@cisco.com: fix typo: surce -> source]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
With the driver stopping and starting the stream each time the driver is
stalled rvin_capture_off() can be folded in to the only caller.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If userspace can't feed the driver with buffers as fast as the driver
consumes them the driver will stop video capturing and wait for more
buffers from userspace, the driver is stalled. Once it have been feed
one or more free buffers it will recover from the stall and resume
capturing.
Instead of continue to capture using the same capture mode as before the
stall allow the driver to choose between single and continuous mode
based on free buffer availability. Do this by stopping capturing when
the driver becomes stalled and restart capturing once it continues. By
doing
this the capture mode will be evaluated each time the driver is
recovering from a stall.
This behavior is needed to fix a bug where continuous capturing mode is
used, userspace is about to stop the stream and is waiting for the last
buffers to be returned from the driver and is not queuing any new
buffers. In this case the driver becomes stalled when there are only 3
buffers remaining streaming will never resume since the driver is
waiting for userspace to feed it more buffers before it can continue
streaming. With this fix the driver will then switch to single capture
mode for the last 3 buffers and a deadlock is avoided. The issue can be
demonstrated using yavta.
$ yavta -f RGB565 -s 640x480 -n 4 --capture=10 /dev/video22
Device /dev/video22 opened.
Device `R_Car_VIN' on `platform:e6ef1000.video' (driver 'rcar_vin') supports video, capture, without mplanes.
Video format set: RGB565 (50424752) 640x480 (stride 1280) field interlaced buffer size 614400
Video format: RGB565 (50424752) 640x480 (stride 1280) field interlaced buffer size 614400
4 buffers requested.
length: 614400 offset: 0 timestamp type/source: mono/EoF
Buffer 0/0 mapped at address 0xb6cc7000.
length: 614400 offset: 614400 timestamp type/source: mono/EoF
Buffer 1/0 mapped at address 0xb6c31000.
length: 614400 offset: 1228800 timestamp type/source: mono/EoF
Buffer 2/0 mapped at address 0xb6b9b000.
length: 614400 offset: 1843200 timestamp type/source: mono/EoF
Buffer 3/0 mapped at address 0xb6b05000.
0 (0) [-] interlaced 0 614400 B 38.240285 38.240303 12.421 fps ts mono/EoF
1 (1) [-] interlaced 1 614400 B 38.282329 38.282346 23.785 fps ts mono/EoF
2 (2) [-] interlaced 2 614400 B 38.322324 38.322338 25.003 fps ts mono/EoF
3 (3) [-] interlaced 3 614400 B 38.362318 38.362333 25.004 fps ts mono/EoF
4 (0) [-] interlaced 4 614400 B 38.402313 38.402328 25.003 fps ts mono/EoF
5 (1) [-] interlaced 5 614400 B 38.442307 38.442321 25.004 fps ts mono/EoF
6 (2) [-] interlaced 6 614400 B 38.482301 38.482316 25.004 fps ts mono/EoF
7 (3) [-] interlaced 7 614400 B 38.522295 38.522312 25.004 fps ts mono/EoF
8 (0) [-] interlaced 8 614400 B 38.562290 38.562306 25.003 fps ts mono/EoF
<blocks forever, waiting for the last buffer>
This fix also allow the driver to switch to single capture mode if
userspace doesn't feed it buffers fast enough. Or the other way around,
if userspace suddenly feeds the driver buffers faster it can switch to
continues capturing mode.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of selecting single or continuous capture mode based on how many
buffers userspace intends to give us select capture mode based on number
of free buffers we can allocate to hardware when the stream is started.
This change is a prerequisite to enable the driver to switch from
continuous to single capture mode (or the other way around) when the
driver is stalled by userspace not feeding it buffers as fast as it
consumes it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This only moves whole structs, defines and functions around, no code is
changed inside any function. The reason for moving this code around is
to prepare for refactoring and fixing of a start/stop stream bug without
having to use forward declarations.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It's possible to grab frames using only one buffer, this should never
have been set to anything else then 1.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use information about pad index when enumerating mbus codes.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Information about pads will be needed when enumerating the media bus
codes in the async complete handler which is run before
rvin_v4l2_probe(). Move the pad lookup to the async bound handler so
they are available when needed.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[hans.verkuil@cisco.com: fix typo: surce -> source]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The pad lookup code can be broken out to increase readability and to
reduce code duplication.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It makes more sense to store the sink and source pads in struct
rvin_graph_entity since that contains other subdevice related
information.
The data type to store pad information in is unsigned int and not int,
change this. While we are at it drop the _idx suffix from the names,
this never made sense.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver supports a single input only, which can be either analog or
digital. If the subdevice supports dv_timings_cap the input is digital
and the driver should not fill in the standard.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The rcar-vin driver only uses one pad, pad number 0.
- All v4l2 operations that did not check that the requested operation
was for pad 0 have been updated with a check to enforce this.
- All v4l2 operations that stored (and later restored) the requested pad
before substituting it for the subdevice pad number have been updated
to not store the incoming pad and simply restore it to 0 after the
subdevice operation is complete.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use rvin_reset_format() in rvin_s_dv_timings() instead of just resetting
a few fields. This fixes an issue where the field format was not
properly set after S_DV_TIMINGS.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These two were forgotten when refactoring the format reset code. If
they are not also reset at the same time as width and height the format
returned from G_FMT will not match reality.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Switch users of the v4l2_of_ APIs to the more generic v4l2_fwnode_ APIs.
Async OF matching is replaced by fwnode matching and OF matching support
is removed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Benoit Parrot <bparrot@ti.com> # i2c/ov2569.c, am437x/am437x-vpfe.c and ti-vpe/cal.c
Tested-by: Hans Verkuil <hans.verkuil@cisco.com> # Atmel sama5d3 board + ov2640 sensor
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Such fallback string is present in the 'soc_camera' version of the R-Car VIN
driver, so need to add it here as well...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The HW can capture both ODD and EVEN fields in separate buffers so it's
possible to support V4L2_FIELD_ALTERNATE. This patch add support for
this mode.
At probe time and when S_STD is called the driver will default to use
V4L2_FIELD_INTERLACED if the subdevice reports V4L2_FIELD_ALTERNATE. The
driver will only change the field type if the subdevice implements
G_STD, if not it will keep the default at V4L2_FIELD_ALTERNATE.
The user can always explicitly ask for V4L2_FIELD_ALTERNATE in S_FMT and
the driver will use that field format.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The height used for V4L2_FIELD_TOP and V4L2_FIELD_BOTTOM where wrong.
The frames only contain one field so the height should be half of the
frame.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It was not possible to scale beyond the image size of the video source
limitation. The output frame would be bigger but the captured image was
limited to the size of the video source.
The error was that the crop boundary was set after the requested frame
size and not the video source size. This patch breaks out the resetting
of the crop, compose and format to separate functions so the error wont
creep back.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver forced whatever field was set by the source subdevice to be
used. This patch allows the user to change from the default field.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The field V4L2_FIELD_INTERLACED is standard dependent and should not
unconditionally be equivalent to V4L2_FIELD_INTERLACED_TB.
This patch adds a check to see if the video standard can be obtained and
if it's a 60 Hz format. If the condition is met V4L2_FIELD_INTERLACED
is treated as V4L2_FIELD_INTERLACED_BT if not as
V4L2_FIELD_INTERLACED_TB.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The media bus format reported by the adv7180 is wrong. Steve Longerbeam
posted a patch which changed the format to UYVY8_2X8 with the commit
message:
Change the media bus format from YUYV8_2X8 to UYVY8_2X8. Colors
now look correct when capturing with the i.mx6 backend. The other
option is to set the SWPC bit in register 0x27 to swap the Cr and Cb
output samples.
The rcar-vin driver was developed and tested with the adv7180 and
therefor suffers from the same issue, looking for the wrong media bus
format. The two errors corrected each other.
This patch takes Steve's patch and merge it with a fix for rcar-vin
driver. The rcar-vin driver is used used in together with the adv7180
och Koelsch and this ensures it will not break while fixing the adv7180
issue. I checked wit Steve and he was fine with me merging the patches.
ADV7180 parts:
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Suggested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
[hans.verkuil@cisco.com: dropped soc_camera/rcar_vin.c patch because that driver will be removed]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The old cropcap video op is now only used to pass the pixelaspect
ratio, so rename it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The primary reason for this change is to prepare for Gen3 support where
there will be more then one possible video source. Each source will have
its own media bus format and code, so it needs to be moved from the per
device structure to a structure used to represent an individual
connection to a video source.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The original drivers code to find a subdevice by looking in the DT grpah
and how the callbacks to the v4l2 async bind framework where poorly
written. The most obvious example of badness was the duplication of data
in the struct rvin_graph_entity.
This patch removes the data duplication, simplifies the parsing of the
DT graph and add checks to the v4l2 callbacks.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The check for if the specific pixelformat is supported on the current
chip should happen in VIDIOC_S_FMT and VIDIOC_TRY_FMT and not when we
try to setup the hardware for streaming.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is done in preparation for Gen3 support where media controller
support will be mandatory for the driver.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix a error from the original driver where v4l2_device_call_until_err()
where used for the pad specific v4l2 operation set_fmt. Also fix up the
error path from this fix so if there is an error it will be propagated
to the caller.
The error path label have also been renamed as a result from a
nitpicking review comment since we are fixing other issues here.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix a error from the original driver where the wrong error code is
returned if the driver fails to get a IRQ number from
platform_get_irq().
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When Gen3 support is added to the driver more then one possible video
source entity will be possible. Knowing that the name entity is a bad
one, rename it to digital since it will deal with the digital input
source.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Align style with the rest of the driver.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this a proper typed array. Drop the old allocate context code since
that is no longer used.
Note that the memops functions now get a struct device pointer instead of
the struct device ** that was there initially (actually a void pointer to
a struct containing only a struct device pointer).
This code is now a lot cleaner.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Stop using alloc_ctx and just fill in the device pointer.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix rcar_vin_try_fmt's use of an inappropriate pad number when calling
the subdev set_fmt function - for the ADV7612, IDs should be non-zero.
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Reviewed-by: Rob Taylor <rob.taylor@codethink.co.uk>
[ulrich.hecht+renesas@gmail.com: adapted to rcar-vin rewrite]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add detection of source pad number for drivers aware of the media controller
API, so that rcar-vin can create device nodes to support modern drivers such
as adv7604.c (for HDMI on Lager) and the converted adv7180.c (for composite)
underneath.
Building rcar_vin gains a dependency on CONFIG_MEDIA_CONTROLLER, in
line with requirements for building the drivers associated with it.
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Rob Taylor <rob.taylor@codethink.co.uk>
[ulrich.hecht+renesas@gmail.com: adapted to rcar-vin rewrite]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drivers/media/platform/rcar-vin/rcar-core.c: In function 'rvin_graph_notify_complete':
drivers/media/platform/rcar-vin/rcar-core.c:65:22: warning: variable 'sd' set but not used [-Wunused-but-set-variable]
struct v4l2_subdev *sd;
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Niklas Söderlund