Since PCI core provides a generic PCI_DEVICE_DATA() macro,
replace contents of EXAR_DEVICE() with former one.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200512140252.67631-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STM32 UART controllers have the built in modem control support using
dedicated gpios which can be enabled using 'st,hw-flow-ctrl' flag in DT.
But there might be cases where the board design need to use different
gpios for modem control.
For supporting such cases, this commit adds modem control gpio support
to STM32 UART controller using mctrl_gpio driver.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Link: https://lore.kernel.org/r/20200420170204.24541-3-mani@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some variants of the samsung tty driver can pick which clock
to use for their baud rate generation. In the DT conversion,
a default clock was selected to be used if a specific one wasn't
assigned and then a comparison of which clock rate worked better
was done. Unfortunately, the comparison was implemented in such
a way that only the default clock was ever actually compared.
Fix this by iterating through all possible clocks, except when a
specific clock has already been picked via clk_sel (which is
only possible via board files).
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/BN6PR04MB06604E63833EA41837EBF77BA3A30@BN6PR04MB0660.namprd04.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e2bd1dcbe1.
In discussion on the mailing list, it has been determined that this is
not the correct type of fix for this issue. Revert it so that we can do
this correctly.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200428032601.22127-1-rananta@codeaurora.org
Cc: Raghavendra Rao Ananta <rananta@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are 3 small TTY/Serial/VT fixes for 5.7-rc5:
- revert for the bcm63xx driver "fix" that was incorrect
- vt unicode console bugfix
- xilinx_uartps console driver fix
All of these have been in linux next with no reported issues
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXrVmRg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymY+ACfelBeBAxlYjuvZ8QpDYSkR9fl8EIAoKeuJocX
TaXtUFCvCSax68siL81w
=L0Rp
-----END PGP SIGNATURE-----
Merge tag 'tty-5.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are three small TTY/Serial/VT fixes for 5.7-rc5:
- revert for the bcm63xx driver "fix" that was incorrect
- vt unicode console bugfix
- xilinx_uartps console driver fix
All of these have been in linux next with no reported issues"
* tag 'tty-5.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: xilinx_uartps: Fix missing id assignment to the console
vt: fix unicode console freeing with a common interface
Revert "tty: serial: bcm63xx: fix missing clk_put() in bcm63xx_uart"
Support 32-bit access for the TX/RX hold registers UTXH and URXH.
This is required for some newer SoCs.
Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested on Odroid HC1 (Exynos5422):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200506080242.18623-3-hyunki00.koo@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch change the name of macro for general usage.
Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested on Odroid HC1 (Exynos5422):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200506080242.18623-1-hyunki00.koo@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3d9231e698
Rajendra writes:
Greg, there are other patches in the series which have a
dependency on this patch [1] would it be possible for you to
drop this patch and instead ack it so it can be taken via the
msm tree?
So dropping it from here.
Reported-by: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Valentine reported seeing:
[ 3.626638] INFO: trying to register non-static key.
[ 3.626639] the code is fine but needs lockdep annotation.
[ 3.626640] turning off the locking correctness validator.
[ 3.626644] CPU: 7 PID: 51 Comm: kworker/7:1 Not tainted 5.7.0-rc2-00115-g8c2e9790f196 #116
[ 3.626646] Hardware name: HiKey960 (DT)
[ 3.626656] Workqueue: events deferred_probe_work_func
[ 3.632476] sd 0:0:0:0: [sda] Optimal transfer size 8192 bytes not a multiple of physical block size (16384 bytes)
[ 3.640220] Call trace:
[ 3.640225] dump_backtrace+0x0/0x1b8
[ 3.640227] show_stack+0x20/0x30
[ 3.640230] dump_stack+0xec/0x158
[ 3.640234] register_lock_class+0x598/0x5c0
[ 3.640235] __lock_acquire+0x80/0x16c0
[ 3.640236] lock_acquire+0xf4/0x4a0
[ 3.640241] _raw_spin_lock_irqsave+0x70/0xa8
[ 3.640245] uart_add_one_port+0x388/0x4b8
[ 3.640248] pl011_register_port+0x70/0xf0
[ 3.640250] pl011_probe+0x184/0x1b8
[ 3.640254] amba_probe+0xdc/0x180
[ 3.640256] really_probe+0xe0/0x338
[ 3.640257] driver_probe_device+0x60/0xf8
[ 3.640259] __device_attach_driver+0x8c/0xd0
[ 3.640260] bus_for_each_drv+0x84/0xd8
[ 3.640261] __device_attach+0xe4/0x140
[ 3.640263] device_initial_probe+0x1c/0x28
[ 3.640265] bus_probe_device+0xa4/0xb0
[ 3.640266] deferred_probe_work_func+0x7c/0xb8
[ 3.640269] process_one_work+0x2c0/0x768
[ 3.640271] worker_thread+0x4c/0x498
[ 3.640272] kthread+0x14c/0x158
[ 3.640275] ret_from_fork+0x10/0x1c
Which seems to be due to the fact that after allocating the uap
structure, nothing initializes the spinlock.
Its a little confusing, as uart_port_spin_lock_init() is one
place where the lock is supposed to be initialized, but it has
an exception for the case where the port is a console.
This makes it seem like a deeper fix is needed to properly
register the console, but I'm not sure what that entails, and
Andy suggested that this approach is less invasive.
Thus, this patch resolves the issue by initializing the spinlock
in the driver, and resolves the resulting warning.
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Reported-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-and-tested-by: Valentin Schneider <valentin.schneider@arm.com>
Link: https://lore.kernel.org/r/20200428184050.6501-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
geni serial needs to express a perforamnce state requirement on CX
powerdomain depending on the frequency of the clock rates.
Use OPP table from DT to register with OPP framework and use
dev_pm_opp_set_rate() to set the clk/perf state.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Cc: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/1588507469-31889-2-git-send-email-rnayak@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When serial console has been assigned to ttyPS1 (which is serial1 alias)
console index is not updated property and pointing to index -1 (statically
initialized) which ends up in situation where nothing has been printed on
the port.
The commit 18cc7ac8a2 ("Revert "serial: uartps: Register own uart console
and driver structures"") didn't contain this line which was removed by
accident.
Fixes: 18cc7ac8a2 ("Revert "serial: uartps: Register own uart console and driver structures"")
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/ed3111533ef5bd342ee5ec504812240b870f0853.1588602446.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By directly using kfree() in different places we risk missing one if
it is switched to using vfree(), especially if the corresponding
vmalloc() is hidden away within a common abstraction.
Oh wait, that's exactly what happened here.
So let's fix this by creating a common abstraction for the free case
as well.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Reported-by: syzbot+0bfda3ade1ee9288a1be@syzkaller.appspotmail.com
Fixes: 9a98e7a80f ("vt: don't use kmalloc() for the unicode screen buffer")
Cc: <stable@vger.kernel.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2005021043110.2671@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 580d952e44 ("tty:
serial: bcm63xx: fix missing clk_put() in bcm63xx_uart") because we
should not be doing a clk_put() if we were not successful in getting a
valid clock reference via clk_get() in the first place.
Fixes: 580d952e44 ("tty: serial: bcm63xx: fix missing clk_put() in bcm63xx_uart")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200501013904.1394-1-f.fainelli@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This tag contains a handful of fixes that I'd like to target for 5.7.
Specifically:
* The change of a linker argument to allow linking with lld.
* A build fix for configurations without a frame pointer.
* A handful of build fixes related the SBI 0.1 vs 0.2 split.
* The removal of STRICT_KERNEL_RWX for !MMU, which isn't useful
-----BEGIN PGP SIGNATURE-----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=MtxP
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
"A handful of fixes.
Specifically:
- fix linker argument to allow linking with lld
- build fix for configurations without a frame pointer
- a handful of build fixes related the SBI 0.1 vs 0.2 split
- remove STRICT_KERNEL_RWX for !MMU, which isn't useful"
* tag 'riscv-for-linus-5.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: select ARCH_HAS_STRICT_KERNEL_RWX only if MMU
riscv: sbi: Fix undefined reference to sbi_shutdown
tty: riscv: Using RISCV_SBI_V01 instead of RISCV_SBI
riscv: sbi: Correct sbi_shutdown() and sbi_clear_ipi() export
riscv: fix vdso build with lld
RISC-V: stacktrace: Declare sp_in_global outside ifdef
Potentially, hvc_open() can be called in parallel when two tasks calls
open() on /dev/hvcX. In such a scenario, if the hp->ops->notifier_add()
callback in the function fails, where it sets the tty->driver_data to
NULL, the parallel hvc_open() can see this NULL and cause a memory abort.
Hence, serialize hvc_open and check if tty->private_data is NULL before
proceeding ahead.
The issue can be easily reproduced by launching two tasks simultaneously
that does nothing but open() and close() on /dev/hvcX.
For example:
$ ./simple_open_close /dev/hvc0 & ./simple_open_close /dev/hvc0 &
Signed-off-by: Raghavendra Rao Ananta <rananta@codeaurora.org>
Link: https://lore.kernel.org/r/20200428032601.22127-1-rananta@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200427122415.47416-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No users of hvcs_driver_string, remove it. This fixes the following gcc
warning:
drivers/tty/hvc/hvcs.c:199:19: warning: ‘hvcs_driver_string’ defined but
not used [-Wunused-const-variable=]
static const char hvcs_driver_string[]
^~~~~~~~~~~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200403071325.3721-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the following messages are seen when booting i.MX8QXP:
fsl-lpuart 5a060000.serial: DMA tx channel request failed, operating without tx DMA (-19)
fsl-lpuart 5a060000.serial: DMA rx channel request failed, operating without rx DMA (-19)
It is not really useful to have such messages on every boot, so change
them to debug level instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200416153453.18825-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
num_chan in register_PCI is used only as an alias for ports_per_aiop. So
drop num_chan and use ports_per_aiop directly.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200417105959.15201-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
init_r_port can access pc104 array out of bounds. pc104 is a 2D array
defined to have 4 members. Each member has 8 submembers.
* we can have more than 4 (PCI) boards, i.e. [board] can be OOB
* line is not modulo-ed by anything, so the first line on the second
board can be 4, on the 3rd 12 or alike (depending on previously
registered boards). It's zero only on the first line of the first
board. So even [line] can be OOB, quite soon (with the 2nd registered
board already).
This code is broken for ages, so just avoid the OOB accesses and don't
try to fix it as we would need to find out the correct line number. Use
the default: RS232, if we are out.
Generally, if anyone needs to set the interface types, a module parameter
is past the last thing that should be used for this purpose. The
parameters' description says it's for ISA cards anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/r/20200417105959.15201-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes below error reported by coccicheck
drivers/tty/serial/bcm63xx_uart.c:848:2-8: ERROR: missing clk_put;
clk_get on line 842 and execution via conditional on line 846
Fixes: ab4382d274 ("tty: move drivers/serial/ to drivers/tty/serial/")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1587472306-105155-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code in vc_do_resize() bounds the memory allocation size to avoid
exceeding MAX_ORDER down the kzalloc() call chain and generating a
runtime warning triggerable from user space. However, not only is it
unwise to use a literal value here, but MAX_ORDER may also be
configurable based on CONFIG_FORCE_MAX_ZONEORDER.
Let's use KMALLOC_MAX_SIZE instead.
Note that prior commit bb1107f7c6 ("mm, slab: make sure that
KMALLOC_MAX_SIZE will fit into MAX_ORDER") the KMALLOC_MAX_SIZE value
could not be relied upon.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Cc: <stable@vger.kernel.org> # v4.10+
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2003281702410.2671@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ba92cf593 ("arm64: dts: actions: s700: Add Clock Management Unit")
breaks the UART on Cubieboard7-lite (based on S700 SoC), This is due to the
fact that generic clk routine clk_disable_unused() disables the gate clks,
and that in turns disables OWL UART (but UART driver never enables it). To
prove this theory, Andre suggested to use "clk_ignore_unused" in kernel
commnd line and it worked (Kernel happily lands into RAMFS world :)).
This commit fix this up by adding clk_prepare_enable().
Fixes: 8ba92cf593 ("arm64: dts: actions: s700: Add Clock Management Unit")
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1587067917-1400-1-git-send-email-amittomer25@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even if the actual screen size is bounded in vc_do_resize(), the unicode
buffer is still a little more than twice the size of the glyph buffer
and may exceed MAX_ORDER down the kmalloc() path. This can be triggered
from user space.
Since there is no point having a physically contiguous buffer here,
let's avoid the above issue as well as reducing pressure on high order
allocations by using vmalloc() instead.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Cc: <stable@vger.kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2003282214210.2671@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As shown in SBI v0.2, the legacy console SBI functions (sbi_console_getchar()
and sbi_console_putchar()) are expected to be deprecated; they have no replacement.
Let's HVC_RISCV_SBI and SERIAL_EARLYCON_RISCV_SBI depends on RISCV_SBI_V01.
Fixes: efca139892 ("RISC-V: Introduce a new config for SBI v0.1")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
For SCIF and HSCIF interfaces the SCxSR register holds the status of
data that is to be read next from SCxRDR register, But where as for
SCIFA and SCIFB interfaces SCxSR register holds status of data that is
previously read from SCxRDR register.
This patch makes sure the status register is read depending on the port
types so that errors are caught accordingly.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kazuhiro Fujita <kazuhiro.fujita.jg@renesas.com>
Signed-off-by: Hao Bui <hao.bui.yg@renesas.com>
Signed-off-by: KAZUMI HARADA <kazumi.harada.rh@renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1585333048-31828-1-git-send-email-kazuhiro.fujita.jg@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit a3cb39d258
("serial: core: Allow detach and attach serial device for console")
changed a bit logic behind lock initialization since for most of the console
driver it's supposed to have lock already initialized even if console is not
enabled. However, it's not the case for Sparc HV console.
Initialize lock explicitly in the ->probe().
Note, there is still an open question should or shouldn't not this driver
register console properly.
Fixes: a3cb39d258 ("serial: core: Allow detach and attach serial device for console")
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Anatoly Pugachev <matorola@gmail.com>
Link: https://lore.kernel.org/r/20200402172026.79478-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of accessing the registers and checking for tx_empty,
use cdns_uart_tx_empty in cdns_uart_console_write function.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/1586413563-29125-3-git-send-email-raviteja.narayanam@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some platforms, the log is corrupted while console is being
registered. It is observed that when set_termios is called, there
are still some bytes in the FIFO to be transmitted.
So, wait for tx_empty inside cdns_uart_console_setup before calling
set_termios.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/1586413563-29125-2-git-send-email-raviteja.narayanam@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's put it to a separate function, named vc_selection_store_chars.
Again, this makes vc_do_selection a bit shorter and more readable.
Having 4 local variables instead of 12 (5.6-rc1) looks much better now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200415093608.10348-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle these actions:
* poking console
* TIOCL_SELCLEAR
* TIOCL_SELMOUSEREPORT
* start/end precomputation
* clear_selection if the console changed
in a separate function, thus making __set_selection_kernel way shorter
and more readable. The function still needs dissection, but we are
approaching.
This includes introduction of vc_selection and renaming
__set_selection_kernel to vc_do_selection.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200415093608.10348-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sh-sci.h file includes the legacy <linux/gpio.h> header
but the driver is actually migrated to use the mctrl_gpio
library so this is not needed.
Cc: George G. Davis <george_davis@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200415180250.221762-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable i is being assigned a value that is never read
and it is being updated later with a new value. The assignment
is redundant and can be removed. Also rename i to ret as this new
name makes makes more sense.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200405135423.383466-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coverity reports the following:
var_compare_op: Comparing chan to null implies that chan might be null.
1234 if (chan)
1235 dmaengine_terminate_all(chan);
1236
Dereference after null check (FORWARD_NULL)
var_deref_op: Dereferencing null pointer chan.
1237 dma_unmap_sg(chan->device->dev, &sport->rx_sgl, 1, DMA_FROM_DEVICE);
Technically, this is correct. But lpuart_dma_rx_free() is guarded by
lpuart_dma_rx_use which is only true if there is a dma channel, see
lpuart_rx_dma_startup(). In any way, this looks bogus. So remove
the superfluous "if (chan)" check and make coverity happy.
Fixes: a092ab25fd ("tty: serial: fsl_lpuart: fix DMA mapping")
Signed-off-by: Michael Walle <michael@walle.cc>
Reported-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200403174942.9594-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the OMAP serial driver to use a GPIO descriptor
for the optional RTS signal.
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200415183927.269445-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver includes <linux/gpio.h> but does not use any symbols
from the file so drop this include.
Cc: Roland Stigge <stigge@antcom.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200415184300.269889-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- A large series from Nick for 64-bit to further rework our exception vectors,
and rewrite portions of the syscall entry/exit and interrupt return in C. The
result is much easier to follow code that is also faster in general.
- Cleanup of our ptrace code to split various parts out that had become badly
intertwined with #ifdefs over the years.
- Changes to our NUMA setup under the PowerVM hypervisor which should
hopefully avoid non-sensical topologies which can lead to warnings from the
workqueue code and other problems.
- MAINTAINERS updates to remove some of our old orphan entries and update the
status of others.
- Quite a few other small changes and fixes all over the map.
Thanks to:
Abdul Haleem, afzal mohammed, Alexey Kardashevskiy, Andrew Donnellan, Aneesh
Kumar K.V, Balamuruhan S, Cédric Le Goater, Chen Zhou, Christophe JAILLET,
Christophe Leroy, Christoph Hellwig, Clement Courbet, Daniel Axtens, David
Gibson, Douglas Miller, Fabiano Rosas, Fangrui Song, Ganesh Goudar, Gautham R.
Shenoy, Greg Kroah-Hartman, Greg Kurz, Gustavo Luiz Duarte, Hari Bathini, Ilie
Halip, Jan Kara, Joe Lawrence, Joe Perches, Kajol Jain, Larry Finger,
Laurentiu Tudor, Leonardo Bras, Libor Pechacek, Madhavan Srinivasan, Mahesh
Salgaonkar, Masahiro Yamada, Masami Hiramatsu, Mauricio Faria de Oliveira,
Michael Neuling, Michal Suchanek, Mike Rapoport, Nageswara R Sastry, Nathan
Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Nick Desaulniers,
Oliver O'Halloran, Po-Hsu Lin, Pratik Rajesh Sampat, Rasmus Villemoes, Ravi
Bangoria, Roman Bolshakov, Sam Bobroff, Sandipan Das, Santosh S, Sedat Dilek,
Segher Boessenkool, Shilpasri G Bhat, Sourabh Jain, Srikar Dronamraju, Stephen
Rothwell, Tyrel Datwyler, Vaibhav Jain, YueHaibing.
-----BEGIN PGP SIGNATURE-----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=ARdm
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Slightly late as I had to rebase mid-week to insert a bug fix:
- A large series from Nick for 64-bit to further rework our exception
vectors, and rewrite portions of the syscall entry/exit and
interrupt return in C. The result is much easier to follow code
that is also faster in general.
- Cleanup of our ptrace code to split various parts out that had
become badly intertwined with #ifdefs over the years.
- Changes to our NUMA setup under the PowerVM hypervisor which should
hopefully avoid non-sensical topologies which can lead to warnings
from the workqueue code and other problems.
- MAINTAINERS updates to remove some of our old orphan entries and
update the status of others.
- Quite a few other small changes and fixes all over the map.
Thanks to: Abdul Haleem, afzal mohammed, Alexey Kardashevskiy, Andrew
Donnellan, Aneesh Kumar K.V, Balamuruhan S, Cédric Le Goater, Chen
Zhou, Christophe JAILLET, Christophe Leroy, Christoph Hellwig, Clement
Courbet, Daniel Axtens, David Gibson, Douglas Miller, Fabiano Rosas,
Fangrui Song, Ganesh Goudar, Gautham R. Shenoy, Greg Kroah-Hartman,
Greg Kurz, Gustavo Luiz Duarte, Hari Bathini, Ilie Halip, Jan Kara,
Joe Lawrence, Joe Perches, Kajol Jain, Larry Finger, Laurentiu Tudor,
Leonardo Bras, Libor Pechacek, Madhavan Srinivasan, Mahesh Salgaonkar,
Masahiro Yamada, Masami Hiramatsu, Mauricio Faria de Oliveira, Michael
Neuling, Michal Suchanek, Mike Rapoport, Nageswara R Sastry, Nathan
Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Nick
Desaulniers, Oliver O'Halloran, Po-Hsu Lin, Pratik Rajesh Sampat,
Rasmus Villemoes, Ravi Bangoria, Roman Bolshakov, Sam Bobroff,
Sandipan Das, Santosh S, Sedat Dilek, Segher Boessenkool, Shilpasri G
Bhat, Sourabh Jain, Srikar Dronamraju, Stephen Rothwell, Tyrel
Datwyler, Vaibhav Jain, YueHaibing"
* tag 'powerpc-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (158 commits)
powerpc: Make setjmp/longjmp signature standard
powerpc/cputable: Remove unnecessary copy of cpu_spec->oprofile_type
powerpc: Suppress .eh_frame generation
powerpc: Drop -fno-dwarf2-cfi-asm
powerpc/32: drop unused ISA_DMA_THRESHOLD
powerpc/powernv: Add documentation for the opal sensor_groups sysfs interfaces
selftests/powerpc: Fix try-run when source tree is not writable
powerpc/vmlinux.lds: Explicitly retain .gnu.hash
powerpc/ptrace: move ptrace_triggered() into hw_breakpoint.c
powerpc/ptrace: create ppc_gethwdinfo()
powerpc/ptrace: create ptrace_get_debugreg()
powerpc/ptrace: split out ADV_DEBUG_REGS related functions.
powerpc/ptrace: move register viewing functions out of ptrace.c
powerpc/ptrace: split out TRANSACTIONAL_MEM related functions.
powerpc/ptrace: split out SPE related functions.
powerpc/ptrace: split out ALTIVEC related functions.
powerpc/ptrace: split out VSX related functions.
powerpc/ptrace: drop PARAMETER_SAVE_AREA_OFFSET
powerpc/ptrace: drop unnecessary #ifdefs CONFIG_PPC64
powerpc/ptrace: remove unused header includes
...
Here is the big set of char/misc/other driver patches for 5.7-rc1.
Lots of things in here, and it's later than expected due to some reverts
to resolve some reported issues. All is now clean with no reported
problems in linux-next.
Included in here is:
- interconnect updates
- mei driver updates
- uio updates
- nvmem driver updates
- soundwire updates
- binderfs updates
- coresight updates
- habanalabs updates
- mhi new bus type and core
- extcon driver updates
- some Kconfig cleanups
- other small misc driver cleanups and updates
As mentioned, all have been in linux-next for a while, and with the last
two reverts, all is calm and good.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXodfvA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynzCQCfROhar3E8EhYEqSOP6xq6uhX9uegAnRgGY2rs
rN4JJpOcTddvZcVlD+vo
=ocWk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc/other driver patches for 5.7-rc1.
Lots of things in here, and it's later than expected due to some
reverts to resolve some reported issues. All is now clean with no
reported problems in linux-next.
Included in here is:
- interconnect updates
- mei driver updates
- uio updates
- nvmem driver updates
- soundwire updates
- binderfs updates
- coresight updates
- habanalabs updates
- mhi new bus type and core
- extcon driver updates
- some Kconfig cleanups
- other small misc driver cleanups and updates
As mentioned, all have been in linux-next for a while, and with the
last two reverts, all is calm and good"
* tag 'char-misc-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (174 commits)
Revert "driver core: platform: Initialize dma_parms for platform devices"
Revert "amba: Initialize dma_parms for amba devices"
amba: Initialize dma_parms for amba devices
driver core: platform: Initialize dma_parms for platform devices
bus: mhi: core: Drop the references to mhi_dev in mhi_destroy_device()
bus: mhi: core: Initialize bhie field in mhi_cntrl for RDDM capture
bus: mhi: core: Add support for reading MHI info from device
misc: rtsx: set correct pcr_ops for rts522A
speakup: misc: Use dynamic minor numbers for speakup devices
mei: me: add cedar fork device ids
coresight: do not use the BIT() macro in the UAPI header
Documentation: provide IBM contacts for embargoed hardware
nvmem: core: remove nvmem_sysfs_get_groups()
nvmem: core: use is_bin_visible for permissions
nvmem: core: use device_register and device_unregister
nvmem: core: add root_only member to nvmem device struct
extcon: axp288: Add wakeup support
extcon: Mark extcon_get_edev_name() function as exported symbol
extcon: palmas: Hide error messages if gpio returns -EPROBE_DEFER
dt-bindings: extcon: usbc-cros-ec: convert extcon-usbc-cros-ec.txt to yaml format
...
Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and some
vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXoHT8w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl3CwCgj/97IKb4K49nV2rDgiV+t/ELWqUAnjBp+Zpd
H2BEdhwCFhq/5CJHKXWH
=JTm1
-----END PGP SIGNATURE-----
Merge tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and
some vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues"
* tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (161 commits)
serial: 8250: Optimize irq enable after console write
serial: 8250: Fix rs485 delay after console write
vt: vt_ioctl: fix use-after-free in vt_in_use()
vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use virtual console
tty: serial: make SERIAL_SPRD depend on COMMON_CLK
tty: serial: fsl_lpuart: fix return value checking
tty: serial: fsl_lpuart: move dma_request_chan()
ARM: dts: tango4: Make /serial compatible with ns16550a
ARM: dts: mmp*: Make the serial ports compatible with xscale-uart
ARM: dts: mmp*: Fix serial port names
ARM: dts: mmp2-brownstone: Don't redeclare phandle references
ARM: dts: pxa*: Make the serial ports compatible with xscale-uart
ARM: dts: pxa*: Fix serial port names
ARM: dts: pxa*: Don't redeclare phandle references
serial: omap: drop unused dt-bindings header
serial: 8250: 8250_omap: Add DMA support for UARTs on K3 SoCs
serial: 8250: 8250_omap: Work around errata causing spurious IRQs with DMA
serial: 8250: 8250_omap: Extend driver data to pass FIFO trigger info
serial: 8250: 8250_omap: Move locking out from __dma_rx_do_complete()
serial: 8250: 8250_omap: Account for data in flight during DMA teardown
...
Commit 7f9803072f ("serial: 8250: Support console on software emulated
rs485 ports") amended serial8250_console_write() with rs485 support, but
positioned the invocation of ->rs485_stop_tx() after re-enablement of
interrupts. The irq handler and ->console_write() are serialized with
the port spinlock, so no problem there, but due to the rs485 delay, the
irq handler may unnecessarily spin for a while. Avoid that by moving
->rs485_stop_tx() before re-enablement of interrupts, which also mirrors
the order at the beginning of serial8250_console_write().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/019839cb1f61b01210b6ff9ac9f9079ca77f8411.1585319447.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to a silly copy-paste mistake, commit 7f9803072f ("serial: 8250:
Support console on software emulated rs485 ports") erroneously pauses
for the duration of delay_rts_before_send after writing to the console,
instead of delay_rts_after_send. Mea culpa.
Fixes: 7f9803072f ("serial: 8250: Support console on software emulated rs485 ports")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/9dd67f33c90d23f7fafa3b81b1e812ddabf9ca24.1585319447.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vt_in_use() dereferences console_driver->ttys[i] without proper locking.
This is broken because the tty can be closed and freed concurrently.
We could fix this by using 'READ_ONCE(console_driver->ttys[i]) != NULL'
and skipping the check of tty_struct::count. But, looking at
console_driver->ttys[i] isn't really appropriate anyway because even if
it is NULL the tty can still be in the process of being closed.
Instead, fix it by making vt_in_use() require console_lock() and check
whether the vt is allocated and has port refcount > 1. This works since
following the patch "vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use
virtual console" the port refcount is incremented while the vt is open.
Reproducer (very unreliable, but it worked for me after a few minutes):
#include <fcntl.h>
#include <linux/vt.h>
int main()
{
int fd, nproc;
struct vt_stat state;
char ttyname[16];
fd = open("/dev/tty10", O_RDONLY);
for (nproc = 1; nproc < 8; nproc *= 2)
fork();
for (;;) {
sprintf(ttyname, "/dev/tty%d", rand() % 8);
close(open(ttyname, O_RDONLY));
ioctl(fd, VT_GETSTATE, &state);
}
}
KASAN report:
BUG: KASAN: use-after-free in vt_in_use drivers/tty/vt/vt_ioctl.c:48 [inline]
BUG: KASAN: use-after-free in vt_ioctl+0x1ad3/0x1d70 drivers/tty/vt/vt_ioctl.c:657
Read of size 4 at addr ffff888065722468 by task syz-vt2/132
CPU: 0 PID: 132 Comm: syz-vt2 Not tainted 5.6.0-rc5-00130-g089b6d3654916 #13
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20191223_100556-anatol 04/01/2014
Call Trace:
[...]
vt_in_use drivers/tty/vt/vt_ioctl.c:48 [inline]
vt_ioctl+0x1ad3/0x1d70 drivers/tty/vt/vt_ioctl.c:657
tty_ioctl+0x9db/0x11b0 drivers/tty/tty_io.c:2660
[...]
Allocated by task 136:
[...]
kzalloc include/linux/slab.h:669 [inline]
alloc_tty_struct+0x96/0x8a0 drivers/tty/tty_io.c:2982
tty_init_dev+0x23/0x350 drivers/tty/tty_io.c:1334
tty_open_by_driver drivers/tty/tty_io.c:1987 [inline]
tty_open+0x3ca/0xb30 drivers/tty/tty_io.c:2035
[...]
Freed by task 41:
[...]
kfree+0xbf/0x200 mm/slab.c:3757
free_tty_struct+0x8d/0xb0 drivers/tty/tty_io.c:177
release_one_tty+0x22d/0x2f0 drivers/tty/tty_io.c:1468
process_one_work+0x7f1/0x14b0 kernel/workqueue.c:2264
worker_thread+0x8b/0xc80 kernel/workqueue.c:2410
[...]
Fixes: 4001d7b7fc ("vt: push down the tty lock so we can see what is left to tackle")
Cc: <stable@vger.kernel.org> # v3.4+
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200322034305.210082-3-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VT_DISALLOCATE ioctl can free a virtual console while tty_release()
is still running, causing a use-after-free in con_shutdown(). This
occurs because VT_DISALLOCATE considers a virtual console's
'struct vc_data' to be unused as soon as the corresponding tty's
refcount hits 0. But actually it may be still being closed.
Fix this by making vc_data be reference-counted via the embedded
'struct tty_port'. A newly allocated virtual console has refcount 1.
Opening it for the first time increments the refcount to 2. Closing it
for the last time decrements the refcount (in tty_operations::cleanup()
so that it happens late enough), as does VT_DISALLOCATE.
Reproducer:
#include <fcntl.h>
#include <linux/vt.h>
#include <sys/ioctl.h>
#include <unistd.h>
int main()
{
if (fork()) {
for (;;)
close(open("/dev/tty5", O_RDWR));
} else {
int fd = open("/dev/tty10", O_RDWR);
for (;;)
ioctl(fd, VT_DISALLOCATE, 5);
}
}
KASAN report:
BUG: KASAN: use-after-free in con_shutdown+0x76/0x80 drivers/tty/vt/vt.c:3278
Write of size 8 at addr ffff88806a4ec108 by task syz_vt/129
CPU: 0 PID: 129 Comm: syz_vt Not tainted 5.6.0-rc2 #11
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20191223_100556-anatol 04/01/2014
Call Trace:
[...]
con_shutdown+0x76/0x80 drivers/tty/vt/vt.c:3278
release_tty+0xa8/0x410 drivers/tty/tty_io.c:1514
tty_release_struct+0x34/0x50 drivers/tty/tty_io.c:1629
tty_release+0x984/0xed0 drivers/tty/tty_io.c:1789
[...]
Allocated by task 129:
[...]
kzalloc include/linux/slab.h:669 [inline]
vc_allocate drivers/tty/vt/vt.c:1085 [inline]
vc_allocate+0x1ac/0x680 drivers/tty/vt/vt.c:1066
con_install+0x4d/0x3f0 drivers/tty/vt/vt.c:3229
tty_driver_install_tty drivers/tty/tty_io.c:1228 [inline]
tty_init_dev+0x94/0x350 drivers/tty/tty_io.c:1341
tty_open_by_driver drivers/tty/tty_io.c:1987 [inline]
tty_open+0x3ca/0xb30 drivers/tty/tty_io.c:2035
[...]
Freed by task 130:
[...]
kfree+0xbf/0x1e0 mm/slab.c:3757
vt_disallocate drivers/tty/vt/vt_ioctl.c:300 [inline]
vt_ioctl+0x16dc/0x1e30 drivers/tty/vt/vt_ioctl.c:818
tty_ioctl+0x9db/0x11b0 drivers/tty/tty_io.c:2660
[...]
Fixes: 4001d7b7fc ("vt: push down the tty lock so we can see what is left to tackle")
Cc: <stable@vger.kernel.org> # v3.4+
Reported-by: syzbot+522643ab5729b0421998@syzkaller.appspotmail.com
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200322034305.210082-2-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kbuild-test reported an error:
config: mips-randconfig-a001-20200321 ...
>> drivers/tty/serial/sprd_serial.c:1175: undefined reference
to `clk_set_parent'
Because some mips Kconfig selects HAVE_CLK but not COMMON_CLK and no
clk_set_parent implemented, so the error was exposed. So adding
dependence on COMMON_CLK can fix this issue.
Fixes: 7ba87cfec7 ("tty: serial: make SERIAL_SPRD not depend on ARCH_SPRD")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200325081427.20312-1-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return value of lpuart_dma_tx_request() is an negative errno on
failure and zero on success.
Fixes: 159381df14 ("tty: serial: fsl_lpuart: fix DMA operation when using IOMMU")
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20200325090658.25967-2-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move dma_request_chan() out of the atomic context. First this call
should not be in the atomic context at all and second the
dev_info_once() may cause a hang because because the console takes this
spinlock, too.
Fixes: 159381df14 ("tty: serial: fsl_lpuart: fix DMA operation when using IOMMU")
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Tested-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lore.kernel.org/r/20200325090658.25967-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The definitons in the dt-binding's gpio header only contains some
constants to be used in device trees. It is not relevant for omap-serial
(as the gpio API hides the details) and in fact unused so it can just be
dropped.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20200321204031.30369-1-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART on K3 SoCs has configurable RX timeout behavior (controlled via
EFR2) and better DMA integration. This allows to transfer as larger
amount data per DMA transfer compared to older SoCs. Add support for
the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-7-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per Advisory 27 of AM437x Silicon errata document, Spurious UART
interrupts may occur when DMA mode (FCR.DMA_MODE) is enabled. The
Interrupt Controller flags that a UART interrupt has occurred; however,
the associated IT_PENDING bit remains set to 1, indicating that no
interrupt is pending. Acknowledge the spurious interrupts for every
occurrence as workaround.
Errata is applicable to all TI SoCs with this IP.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-6-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although same 8250 compliant UART IP is reused across different SoC,
their integration wrt DMA varies greatly across SoCs. Therefore,
different SoC may need to use different FIFO trigger level for DMA
event and DMA configuration parameters. Provide a way to pass this
information via driver data. This is required to support UART DMA on
AM654/J721e SoCs.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-5-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Caller functions of __dma_rx_do_complete() already hold rx_dma_lock.
Therefore move locking out of the function to avoid need to release and
reacquire lock.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-4-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take into account data stuck in DMA internal buffers before pushing data
to higher layer. dma_tx_state has "in_flight_bytes" member that provides
this information.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-3-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Terminate and flush DMA internal buffers, before pushing RX data to
higher layer. Otherwise, this will lead to data corruption, as driver
would end up pushing stale buffer data to higher layer while actual data
is still stuck inside DMA hardware and has yet not arrived at the
memory.
While at that, replace deprecated dmaengine_terminate_all() with
dmaengine_terminate_async().
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call stop_rx() to halt reception when throttle is requested. Update
unthrottle callback to restart reception.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319103230.16867-3-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When port's throttle callback is called, it should stop pushing any more
data into TTY buffer to avoid buffer overflow. This means driver has to
stop HW from receiving more data and assert the HW flow control. For
UARTs with auto HW flow control (such as 8250_omap) manual assertion of
flow control line is not possible and only way is to allow RX FIFO to
fill up, thus trigger auto HW flow control logic.
Therefore make sure that 8250 generic IRQ handler does not drain data
when port is stopped (i.e UART_LSR_DR is unset in read_status_mask). Not
servicing, RX FIFO would trigger auto HW flow control when FIFO
occupancy reaches preset threshold, thus halting RX.
Since, error conditions in UART_LSR register are cleared just by reading
the register, data has to be drained in case there are FIFO errors, else
error information will lost.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319103230.16867-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that all bytes are transmitted out of Uart by monitoring
CDNS_UART_SR_TACTIVE bit as well.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Maarten Brock <m.brock@vanmierlo.com>
Link: https://lore.kernel.org/r/e2514818af5973be291cc117d07739f068b71639.1584610774.git.shubhrajyoti.datta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
set_termios function should not wait for the transmit FIFO empty
(CDNS_UART_SR_TXEMPTY) unconditionally. The tty layer takes care
of it based on the parameter passed (TCSANOW/TCSADRAIN/TCSAFLUSH).
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/536e190dd5bbb474007a67e6323c048288942a28.1584610774.git.shubhrajyoti.datta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7765435030 ("take compat TIOC[SG]SERIAL treatment into
tty_compat_ioctl()") changed the compat version of TIOCGSERIAL to start
checking for the presence of the ->set_serial function pointer rather
than ->get_serial. This appears to be a copy-and-paste error, since
->get_serial is the function pointer that is called as well as the
pointer that is checked by the non-compat version of TIOCGSERIAL.
Fix this by checking the correct function pointer.
Fixes: 7765435030 ("take compat TIOC[SG]SERIAL treatment into tty_compat_ioctl()")
Cc: <stable@vger.kernel.org> # v4.20+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200224182044.234553-3-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7765435030 ("take compat TIOC[SG]SERIAL treatment into
tty_compat_ioctl()") changed the compat version of TIOCGSERIAL to start
copying a whole 'serial_struct32' to userspace rather than individual
fields, but failed to initialize all padding and fields -- namely the
hole after the 'iomem_reg_shift' field, and the 'reserved' field.
Fix this by initializing the struct to zero.
[v2: use sizeof, and convert the adjacent line for consistency.]
Reported-by: syzbot+8da9175e28eadcb203ce@syzkaller.appspotmail.com
Fixes: 7765435030 ("take compat TIOC[SG]SERIAL treatment into tty_compat_ioctl()")
Cc: <stable@vger.kernel.org> # v4.20+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200224182044.234553-2-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current version of the TTY code unlocks the tty_struct(s) before
release_tty() rather than after. Moreover, tty_unlock_pair() no longer
exists. Thus, remove the outdated comments regarding tty_unlock_pair().
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200224073359.292795-1-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header file related to Kernel driver API to route trace data.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200302143642.GA3335@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header file related to the HVC driver.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200301170419.GA7125@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Also rewrite the code in a standard if-form instead of ugly
conditional operators.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200311092905.24362-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200311092930.24433-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't need to cleanup sprd_port anymore, since we've dropped the way
of using the sprd_port[] array to get port index.
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200318105049.19623-3-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch simplifies the process of getting serial port number, with
this patch, serial devices must have aliases configured in devicetree.
The serial port searched out via sprd_port array maybe wrong if we don't
have serial alias defined in devicetree, and specify console with command
line, we would get the wrong port number if other serial ports probe
failed before console's. So using aliases is mandatory.
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200318105049.19623-2-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It would be too tricky and error prone to allow DMA operations on
kernel console.
One of the concern is when DMA is a separate device, for example on
Intel CherryTrail platforms, and might need special work around to be
functional, see the commit
eebb3e8d8a ("ACPI / LPSS: override power state for LPSS DMA device")
for more information.
Another one is that kernel console is used in atomic context, e.g.
when printing crucial information to the user (Oops or crash),
and DMA may not serve due to power management complications
including non-atomic ACPI calls but not limited to it (see above).
Besides that, other concerns are described in the commit
84b40e3b57 ("serial: 8250: omap: Disable DMA for console UART")
done for OMAP UART and may be repeated here.
Disable any kind of DMA operations on kernel console due to above concerns.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200217114016.49856-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Doing any kind of power management for kernel console is really bad idea.
First of all, it runs in poll and atomic mode. This fact attaches a limitation
on the functions that might be called. For example, pm_runtime_get_sync() might
sleep and thus can't be used. This call needs, for example, to bring the device
to powered on state on the system, where the power on sequence may require
on-atomic operations, such as Intel Cherrytrail with ACPI enumerated UARTs.
That said, on ACPI enabled platforms it might even call firmware for a job.
On the other hand pm_runtime_get() doesn't guarantee that device will become
powered on fast enough.
Besides that, imagine the case when console is about to print a kernel Oops and
it's powered off. In such an emergency case calling the complex functions is
not the best what we can do, taking into consideration that user wants to see
at least something of the last kernel word before it passes away.
Here we modify the 8250 console code to prevent runtime power management.
Note, there is a behaviour change for OMAP boards. It will require to detach
kernel console to become idle.
Link: https://lists.openwall.net/linux-kernel/2018/09/29/65
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200217114016.49856-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the future we would like to disable power management on the serial devices
used as kernel consoles to avoid weird behaviour in some cases. However,
disabling PM may prevent system to go to deep sleep states, which in its turn
leads to the higher power consumption.
Tony Lindgren proposed a work around, i.e. allow user to detach such consoles
to make PM working again. In case user wants to see what's going on, it also
provides a mechanism to attach console back.
Link: https://lists.openwall.net/linux-kernel/2018/09/29/65
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200217114016.49856-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 175b558d0e.
When the user configures a kernel without support for Samsung SoCs, it
makes no sense to ask the user about enabling "Samsung SoC serial
support", as Samsung serial ports can only be found on Samsung SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200306102301.16870-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should validate if the 'sup' is NULL or not before freeing DMA
memory, to fix below warning.
"drivers/tty/serial/sprd_serial.c:1141 sprd_remove()
error: we previously assumed 'sup' could be null (see line 1132)"
Fixes: f4487db58e ("serial: sprd: Add DMA mode support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lanqing Liu <liuhhome@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/e2bd92691538e95b04a2c2a728f3292e1617018f.1584325957.git.liuhhome@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function sprd_console_setup() would be called from .probe() which can
be called after freeing __init functions, for example the .probe() would
return -EPROBE_DEFER since it depends on clock modules.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200316101930.9962-3-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SPRD serial driver need to know which serial port would be used as
console in an early period during initialization, the purpose is to
keep the console port alive as possible even if there's some error
caused by no clock configured under serial devicetree nodes. But with
the patch [1], the console port couldn't be identified if missing
console command line.
So this patch adds using another interface to do check by reading
stdout-path.
[1] https://lore.kernel.org/lkml/20190826072929.7696-4-zhang.lyra@gmail.com/
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200316101930.9962-2-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ev_byte_channel_send() assumes that its third argument is a 16 byte
array. Some places where it is called it may not be (or we can't
easily tell if it is). Newer compilers have started producing warnings
about this, so make sure we actually pass a 16 byte array.
There may be more elegant solutions to this, but the driver is quite
old and hasn't been updated in many years.
The warnings (from a powerpc allyesconfig build) are:
In file included from include/linux/byteorder/big_endian.h:5,
from arch/powerpc/include/uapi/asm/byteorder.h:14,
from include/asm-generic/bitops/le.h:6,
from arch/powerpc/include/asm/bitops.h:250,
from include/linux/bitops.h:29,
from include/linux/kernel.h:12,
from include/asm-generic/bug.h:19,
from arch/powerpc/include/asm/bug.h:109,
from include/linux/bug.h:5,
from include/linux/mmdebug.h:5,
from include/linux/gfp.h:5,
from include/linux/slab.h:15,
from drivers/tty/ehv_bytechan.c:24:
drivers/tty/ehv_bytechan.c: In function ‘ehv_bc_udbg_putc’:
arch/powerpc/include/asm/epapr_hcalls.h:298:20: warning: array subscript 1 is outside array bounds of ‘const char[1]’ [-Warray-bounds]
298 | r6 = be32_to_cpu(p[1]);
include/uapi/linux/byteorder/big_endian.h:40:51: note: in definition of macro ‘__be32_to_cpu’
40 | #define __be32_to_cpu(x) ((__force __u32)(__be32)(x))
| ^
arch/powerpc/include/asm/epapr_hcalls.h:298:7: note: in expansion of macro ‘be32_to_cpu’
298 | r6 = be32_to_cpu(p[1]);
| ^~~~~~~~~~~
drivers/tty/ehv_bytechan.c:166:13: note: while referencing ‘data’
166 | static void ehv_bc_udbg_putc(char c)
| ^~~~~~~~~~~~~~~~
Fixes: dcd83aaff1 ("tty/powerpc: introduce the ePAPR embedded hypervisor byte channel driver")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
[mpe: Trim warnings from change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200109183912.5fcb52aa@canb.auug.org.au
Shift cases one level left. This makes the code more readable and some
lines need not wrap anymore.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200316065911.11024-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have a helper called rounddown for these modulo computations. So use
it.
No functional change intended and "objdump -d" proves that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200316065911.11024-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of awkward ternary operator with comparison, use simple min()
for blankinterval and vesa_off_interval.
No functional change intended and "objdump -d" proves that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200316065911.11024-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As Joe suggests, dynamic debug can print module name and line number
along with message. So remove __FILE__ and __LINE__ from all those
pr_debug calls.
Out of curiosity, I measured the savings, 200 bytes of code are gone.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Suggested-by: Joe Perches <joe@perches.com>
Link: https://lore.kernel.org/r/20200316064910.4941-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The merge commit cb05c6c82f (Merge 5.6-rc5 into tty-next) introduced a
double lock to set_selection_kernel. vc_sel.lock is locked both in
set_selection_kernel and its callee __set_selection_kernel now.
Remove the latter.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20200316064544.4799-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko