- reduce the irq disabled section, even for a debugfs file this was
way too long.
- always disable irqs when taking the lock.
v2: Thou shalt not mistake locking for reference counting, so:
- reference count the error_state to protect from concurent freeeing.
This will be only really used in the next patch.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
gpu reset is a very important piece of our infrastructure.
Unfortunately we only really it test by actually hanging the gpu,
which often has bad side-effects for the entire system. And the gpu
hang handling code is one of the rather complicated pieces of code we
have, consisting of
- hang detection
- error capture
- actual gpu reset
- reset of all the gem bookkeeping
- reinitialition of the entire gpu
This patch adds a debugfs to selectively stopping rings by ceasing to
update the hw tail pointer, which will result in the gpu no longer
updating it's head pointer and eventually to the hangcheck firing.
This way we can exercise the gpu hang code under controlled conditions
without a dying gpu taking down the entire systems.
Patch motivated by me forgetting to properly reinitialize ppgtt after
a gpu reset.
Usage:
echo $((1 << $ringnum)) > i915_ring_stop # stops one ring
echo 0xffffffff > i915_ring_stop # stops all, future-proof version
then run whatever testload is desired. i915_ring_stop automatically
resets after a gpu hang is detected to avoid hanging the gpu to fast
and declaring it wedged.
v2: Incorporate feedback from Chris Wilson.
v3: Add the missing cleanup.
v4: Fix up inconsistent size of ring_stop_read vs _write, noticed by
Eugeni Dodonov.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Every time we use the device after a period of idleness, check that the
power management setup is still sane. This is to workaround a bug
whereby it seems that we begin suppressing power management interrupts,
preventing SandyBridge+ from going into turbo mode.
This patch does have a side-effect. It removes the mark-busy for just
moving the cursor - we don't want to increase the render clock just for
the sprite, though we may want to bump the display frequency. I'd argue
that we do not, and certainly don't want to take the struct_mutex here
due to the large latencies that introduces.
References: https://bugs.freedesktop.org/show_bug.cgi?id=44006
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To get the fun stuff out of the way, the legacy hws is allocated by
userspace when the gpu needs a gfx hws. And there's no reference-counting
going on, so userspace can simply screw everyone over.
At least it's not as horrible as i810, where the ringbuffer is allocated
by userspace ...
We can't fix this disaster, but we can at least tidy up the code a
bit to make things clearer:
- Drop the drm ioremap indirection.
- Add a new new read_legacy_status_page to paper over the differences
between the legacy gfx hws and the physical hws shared with the
new ringbuffer code.
- Add a pointer in dev_priv->dri1 for the cpu addresses - that one is
an iomem remapping as opposed to all other hw status pages. This is
just prep work to make sparse happy.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wohoo!
Now we only need to move all the gem/kms stuff that accidentally
landed in i915_dma.c out of it, and this will be our legacy dri1
grave-yard.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... and hide it in i915_dma.c.
This way all the legacy stuff dealing with READ_BREADCRUMB and
LP_RING and friends is in i915_dma.c.
v2: Rebase on top of Chris Wilson's rework irq handling code.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's just get this out of the way.
v2: Rebase against ENODEV changes.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Assigned in setparam, used never.
I didn't bother to dig through the archives to figure out what
this was supposed to do.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... and shove allow_batchbuffer in there. More dragons will
follow suit.
There's the curious case that we allow this for KMS ...
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i915_dma.c contains most of the old dri1 horror-show, so move
the remaining bits there, too. The code has been removed and
the only thing left are some stubs to ensure that userspace
doesn't try to use this stuff. vblank_pipe_set only returns 0
without any side-effects, so we can even stub it out with
the canonical drm_noop.
v2: Rebase against ENODEV changes.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
vblank_pipe was intended to be used for tracking DRI1 state. However,
the vblank_pipe reported to DRI1 is fixed to umask both pipes, and the
dev_priv->vblank_pipe unused and superfluous.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The waiting_seqno is not terribly useful, and as such we can remove it
so that we'll be able to extract lockless code.
v2: Keep the information for error_state (Chris)
Check if ring is initialized in hangcheck (Chris)
Capture the waiting ring (Chris)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: add some bikeshed to clarify a comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This extra bit of interrupt enabling code doesn't belong in the wait
seqno function. If anything we should pull it out to a helper so the
throttle code can also use it. The history is a bit vague, but I am
going to attempt to just dump it, unless someone can argue otherwise.
Removing this allows for a shared lock free wait seqno function. To keep
tabs on this issue though, the IER value is stored on error capture
(recommended by Chris Wilson)
v2: fixed typo EIR->IER (Ben)
Fix some white space (Ben)
Move IER capture to globally instead of per ring (Ben)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: ier is a 16 bit reg on gen2!]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This originates from a hack by me to quickly fix a bug in an earlier
patch where we needed control over whether or not waiting on a seqno
actually did any retire list processing. Since the two operations aren't
clearly related, we should pull the parameter out of the wait function,
and make the caller responsible for retiring if the action is desired.
The only function call site which did not get an explicit retire_request call
(on purpose) is i915_gem_inactive_shrink(). That code was already calling
retire_request a second time.
v2: don't modify any behavior excepit i915_gem_inactive_shrink(Daniel)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On later gen3, you are able to select the meaning of the FlipPending
status bit in IIR and change it to FlipDone. This was sometimes done by
the BIOS leading to confusion on just how pageflipping worked on gen3.
Simplify the implementation by using the legacy meaning for all gen3
machines.
Note: this makes all gen3 machines equally broken...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And remove the cargo-culted copy from the valleyview irq handler.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always true these days. It has been added originally to work
around some issues with the agp layer in 2.6.29:
commit ac5c4e7618
Author: Dave Airlie <airlied@redhat.com>
Date: Fri Dec 19 15:38:34 2008 +1000
drm/i915: GEM on PAE has problems - disable it for now.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We slightly modify the initialisation sequence to move the
initialisation of the memory managers earlier and in particular before
probing outputs and detecting any existing output configuration. This is
essential if we wish to track preallocated objects and preserve them
whilst initialising GEM.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The use of the mm_list by deferred-free breaks the following patches to
extend the range of objects tracked. We can simplify things if we just
make the unbind during free uninterrutible.
Note that unbinding should never fail, because we hold an additional
reference on every active object. Only the ilk vt-d workaround breaks
this, but already takes care of not failing by waiting for the gpu to
quiescent non-interruptible. But the existence of the deferred free
list casted some doubts on this theory, hence WARN if the unbind fails
and only then retry non-interruptible.
We can kill this additional code after a release in case the theory is
indeed right and no one has hit that WARN.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Simplify object tracking by removing the inactive but pinned list. The
only place where this was used is for counting the available memory,
which is just as easy performed by checking all objects on the rare
occasions it is required (application startup). For ease of debugging,
we keep the reporting of pinned objects through the error-state and
debugfs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was only used by one external caller who would just be as happy
with evict-everything, so perform the replacement and make the function
private.
In the process we note that unbinding the inactive list should not fail,
and make it a warning instead.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PCH PLLs aren't required for outputs on the CPU, so we shouldn't just
treat them as part of the pipe.
So split the code out and manage PCH PLLs separately, allocating them
when needed or trying to re-use existing PCH PLL setups when the timings
match.
v2: add num_pch_pll field to dev_priv (Daniel)
don't NULL the pch_pll pointer in disable or DPMS will fail (Jesse)
put register offsets in pll struct (Chris)
v3: Decouple enable/disable of PLLs from get/put.
v4: Track temporary PLL disabling during modeset
v5: Tidy PLL initialisation by only checking for num_pch_pll == 0 (Eugeni)
v6: Avoid mishandling allocation failure by embedding the small array of
PLLs into the device struct
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44309
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> (up to v2)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v3+)
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Tested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename obj->tiling_changed to obj->fence_dirty so that it is clear that
it flags when the parameters for an active fence (including the
no-fence) register are changed.
Also, do not set this flag when the object does not have a fence
register allocated currently and the gpu does not depend upon the
unfence. This case works exactly like when a tiled object lost its
fence and hence does not need additional handling for the tiling
change in the code.
v2: Use fence_dirty to better express what the flag tracks and add a few
more details to the comments to serve as a reminder of how the GPU also
uses the unfenced register slot.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add some bikeshed to the commit message about the stricter
use of fence_dirty.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Almost all of the errors related __iomem problems.
Most of the changes here are trivial, however there is plenty of chance
for yank/paste errors.
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we now never pipeline a fence update, obj->last_fenced_ring is always
the same as the obj->ring whenever obj->last_fenced_seqno is active, so
remove it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we now no longer track a pipelined fence change, we never use
ring->setup_seqno and can kill it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We never succeeded in getting pipelined fencing to work (unresolved
spurious GPU hangs), so begin the process of dismantling and removal
the broken code.
Step 1 is the removal of the pipeline parameter to get_fence().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This should contain all the changes which require no thought to make
sparse happy.
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After a gpu reset we need to re-init some of the hw state we only
initialize when modeset is enabled, like rc6, hw contexts or render/GT
core clock gating and workaround register settings.
Note that this patch has a small change in the resume code:
- rc6 on gen6+ is only restored for the modeset case (for more
consistency with other callsites). This is no problem because recent
kernels refuse to load drm/i915 without kms on gen6+
- rc6/emon on ilk is only restored for the modeset case. This is no
problem because rc6 is disabled by default on ilk, and ums on ilk
has never really been a supported option outside of horrible rhel
backports.
v2: Chris Wilson noticed that we not only fail to restore the clock
gating settings after gpu reset.
v3: Move the call to modeset_init_hw in _reset out of the
struct_mutext protected area - other callers don't hold it, too.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Merge rc6 information into the power group for our device. Until now the
i915 driver has not had any sysfs entries (aside from the connector
stuff enabled by drm core). Since it seems like we're likely to have
more in the future I created a new file for sysfs stubs, as well as the
rc6 sysfs functions which don't really belong elsewhere (perhaps
i915_suspend, but most of the stuff is in intel_display,c).
displays rc6 modes enabled (as a hex mask):
cat /sys/class/drm/card0/power/rc6_enable
displays #ms GPU has been in rc6 since boot:
cat /sys/class/drm/card0/power/rc6_residency_ms
displays #ms GPU has been in deep rc6 since boot:
cat /sys/class/drm/card0/power/rc6p_residency_ms
displays #ms GPU has been in deepest rc6 since boot:
cat /sys/class/drm/card0/power/rc6pp_residency_ms
Important note: I've seen on SNB that even when RC6 is *not* enabled the
rc6 register seems to have a random value in it. I can only guess at the
reason reason for this. Those writing tools that utilize this value need
to be careful and probably want to scrutinize the value very carefully.
v2: use common rc6 residency units to milliseconds for the other RC6 types
v3: don't create sysfs files for GEN <= 5
add a rc6_enable to show a mask of enabled rc6 types
use unmerge instead of remove for sysfs group
squash intel_enable_rc6() extraction into this patch
v4: rename sysfs files (Chris)
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>f
CC: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: squash in the 64bit division fix by Chris Wilson.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In theory this will have performance and power improvements. Performance
because we don't need to stall when the scanout BO is busy, and power
because we don't have to stall when the BO is busy (and the ring can
even go to sleep if the HW supports it).
v2:
squash 2 patches into 1 (me)
un-inline the enable_semaphores function (Daniel)
remove comment about SNB hangs from i915_gem_object_sync (Chris)
rename intel_enable_semaphores to i915_semaphore_is_enabled (me)
removed page flip comment; "no why" (Chris)
To address other comments from Daniel (irc):
update the comment to say 'vt-d is crap, don't enable semaphores'
- I think you misinterpreted Chris' comment, it already exists.
checking out whether we can pageflip on the render ring on ivb (didn't
work on early silicon)
- We don't want to enable workarounds for early silicon unless we have
to.
- I can't find any references in the docs about this.
optionally use it if the fb is already busy on the render ring
- This should be how the code already worked, unless I am
misunderstanding your meaning.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By simplifying the rules to calling get_fence when writing to the
through the GTT in a tiled manner, and calling put_fence before writing
to the object through the GTT in a linear manner, the code becomes
clearer and there is less chance of making a mistake.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: fixed up conflict with ppgtt code and spelling in a new
comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter wrote
First pull request for 3.5-next, slightly large than usual because new
things kept coming in since the last pull for 3.4.
Highlights:
- first batch of hw enablement for vlv (Jesse et al) and hsw (Eugeni). pci
ids are not yet added, and there's still quite a few patches to merge
(mostly modesetting). To make QA easier I've decided to merge this stuff
in pieces.
- loads of cleanups and prep patches spurred by the above. Especially vlv
is a real frankenstein chip, but also hsw is stretching our driver's
code design. Expect more to come in this area for 3.5.
- more gmbus fixes, cleanups and improvements by Daniel Kurtz. Again,
there are more patches needed (and some already queued up), but I wanted
to split this a bit for better testing.
- pwrite/pread rework and retuning. This series has been in the works for
a few months already and a lot of i-g-t tests have been created for it.
Now it's finally ready to be merged. Note that one patch in this series
touches include/pagemap.h, that patch is acked-by akpm.
- reduce mappable pressure and relocation throughput improvements from
Chris.
- mmap offset exhaustion mitigation by Chris Wilson.
- a start at figuring out which codepaths in our messy dri1/ums+gem/kms
driver we actually need to support by bailing out of unsupported case.
The driver now refuses to load without kms on gen6+ and disallows a few
ioctls that userspace never used in certain cases. More of this will
definitely come.
- More decoupling of global gtt and ppgtt.
- Improved dual-link lvds detection by Takashi Iwai.
- Shut up the compiler + plus fix the fallout (Ben)
- Inverted panel brightness handling (mostly Acer manages to break things
in this way).
- Small fixlets and adjustements and some minor things to help debugging.
Regression-wise QA reported quite a few issues on ivb, but all of them
turned out to be hw stability issues which are already fixed in
drm-intel-fixes (QA runs the nightly regression tests on -next alone,
without -fixes automatically merged in). There's still one issue open on
snb, it looks like occlusion query writes are not quite as cache coherent
as we've expected. With some of the pwrite adjustements we can now
reliably hit this. Kernel workaround for it is in the works."
* 'drm-intel-next' of git://people.freedesktop.org/~danvet/drm-intel: (101 commits)
drm/i915: VCS is not the last ring
drm/i915: Add a dual link lvds quirk for MacBook Pro 8,2
drm/i915: make quirks more verbose
drm/i915: dump the DMA fetch addr register on pre-gen6
drm/i915/sdvo: Include YRPB as an additional TV output type
drm/i915: disallow gem init ioctl on ilk
drm/i915: refuse to load on gen6+ without kms
drm/i915: extract gt interrupt handler
drm/i915: use render gen to switch ring irq functions
drm/i915: rip out old HWSTAM missed irq WA for vlv
drm/i915: open code gen6+ ring irqs
drm/i915: ring irq cleanups
drm/i915: add SFUSE_STRAP registers for digital port detection
drm/i915: add WM_LINETIME registers
drm/i915: add WRPLL clocks
drm/i915: add LCPLL control registers
drm/i915: add SSC offsets for SBI access
drm/i915: add port clock selection support for HSW
drm/i915: add S PLL control
drm/i915: add PIXCLK_GATE register
...
Conflicts:
drivers/char/agp/intel-agp.h
drivers/char/agp/intel-gtt.c
drivers/gpu/drm/i915/i915_debugfs.c
There are 5 DDI ports on Haswell. Port A is always enabled, and is the one
connected to eDP, and Port E is the one that can be connected to the PCH
using FDI protocol. Ports B, C, D and E can be used for digital outputs.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds product definitions for desktop, mobile and server boards.
v2: split into a separate patch, add .has_pch_split feature.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The macro is becoming too complex and with VLV upon us it can lead to
confusion. So transforming this into a feature check instead.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
[danvet: fixed conflict with is_valleyview addition.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Totally unexpected that this regressed. Luckily it sounds like we just
need to have dmar disable on the igfx, not the entire system. At least
that's what a few days of testing between Tony Vroon and me indicates.
Reported-by: Tony Vroon <tony@linx.net>
Cc: Tony Vroon <tony@linx.net>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43024
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows to select which rc6 modes are to be used via kernel parameter,
via a bitmask parameter. E.g.:
- to enable rc6, i915_enable_rc6=1
- to enable rc6 and deep rc6, i915_enable_rc6=3
- to enable rc6 and deepest rc6, use i915_enable_rc6=5
- to enable rc6, deep and deepest rc6, use i915_enable_rc6=7
Please keep in mind that the deepest RC6 state really should NOT be used
by default, as it could potentially worsen the issues with deep RC6. So do
enable it only when you know what you are doing. However, having it around
could help solving possible future rc6-related issues and their debugging
on user machines.
Note that this changes behavior - previously, value of 1 would enable both
RC6 and deep RC6. Now it should only enable RC6 and deep/deepest RC6
stages must be enabled manually.
v2: address Chris Wilson comments and clean up the code.
References: https://bugs.freedesktop.org/show_bug.cgi?id=42579
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ValleyView handles force wake differently than previous chipsets, so add
a couple of new functions for it. But leave it disabled by default
until we test it (need a chip with the Punit enabled first).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ValleyView puts some display related registers like the PLL controls and
dividers behind the DPIO bus. Add simple indirect register access
routines to get to those registers.
v2: move new wait_for macro to intel_drv.h (Ben)
fix DPIO_PKT double write (Ben)
add debugfs file
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For use by the rest of the ValleyView code.
v2: fix desktop variant to not set is_mobile (Ben)
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This memory is always allocated, and it is always a fixed size, so just
allocate it along with the rest of the driver state.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no GMBUS "disabled" port 0, nor "reserved" port 7.
For the other 6 ports there is a fixed 1:1 mapping between pin pairs and
gmbus ports, which means every real gmbus port has a gpio pin.
Given these realizations, clean up gmbus initialization.
Tested on Sandybridge (gen 6, PCH == CougarPoint) hardware.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of letting other modules directly access the ->gmbus array,
introduce intel_gmbus_get_adapter() for looking up an i2c_adapter
for a given gmbus port identifier. This will enable later refactoring
of the gmbus port list.
Note: Before requesting an adapter for a given gmbus port number, the
driver must first check its validity using i2c_intel_gmbus_is_port_valid().
If this check fails, a call to intel_gmbus_get_adapter() will WARN_ON and
return NULL. This is relevant for parts of the driver that read a port
from VBIOS, which might be improperly initialized and contain an invalid
port. In these cases, the driver must fall back to using a safer default
port.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No longer needed.
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We try to avoid writing the relocations through the uncached GTT, if the
buffer is currently in the CPU write domain and so will be flushed out to
main memory afterwards anyway. Also on SandyBridge we can safely write
to the pages in cacheable memory, so long as the buffer is LLC mapped.
In either of these cases, we therefore do not need to force the
reallocation of the buffer into the mappable region of the GTT, reducing
the aperture pressure.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... because this is what it actually doesn now that we have the global
gtt vs. ppgtt split.
Also move it to the other global gtt functions in i915_gem_gtt.c
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Again, Valleyview modes these around, so make the mmio base more
explicit to consolidate the base address computations to one
HAS_PCH_SPLIT check.
v2: Fix up the PCH_SPLIT braino ... it actually works that way round.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter