When selecting a new window, tcp_select_window() tries not to shrink
the offered window by using the maximum of the remaining offered window
size and the newly calculated window size. The newly calculated window
size is always a multiple of the window scaling factor, the remaining
window size however might not be since it depends on rcv_wup/rcv_nxt.
This means we're effectively shrinking the window when scaling it down.
The dump below shows the problem (scaling factor 2^7):
- Window size of 557 (71296) is advertised, up to 3111907257:
IP 172.2.2.3.33000 > 172.2.2.2.33000: . ack 3111835961 win 557 <...>
- New window size of 514 (65792) is advertised, up to 3111907217, 40 bytes
below the last end:
IP 172.2.2.3.33000 > 172.2.2.2.33000: . 3113575668:3113577116(1448) ack 3111841425 win 514 <...>
The number 40 results from downscaling the remaining window:
3111907257 - 3111841425 = 65832
65832 / 2^7 = 514
65832 % 2^7 = 40
If the sender uses up the entire window before it is shrunk, this can have
chaotic effects on the connection. When sending ACKs, tcp_acceptable_seq()
will notice that the window has been shrunk since tcp_wnd_end() is before
tp->snd_nxt, which makes it choose tcp_wnd_end() as sequence number.
This will fail the receivers checks in tcp_sequence() however since it
is before it's tp->rcv_wup, making it respond with a dupack.
If both sides are in this condition, this leads to a constant flood of
ACKs until the connection times out.
Make sure the window is never shrunk by aligning the remaining window to
the window scaling factor.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
zap_completion_queue() retrieves skbs from completion_queue where they have
zero skb->users counter. Before dev_kfree_skb_any() it should be non-zero
yet, so it's increased now.
Reported-and-tested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In br_fdb_cleanup() next_timer and this_timer are in jiffies, so they
should be compared using the time_after() macro.
Signed-off-by: Fabio Checconi <fabio@gandalf.sssup.it>
Signed-off-by: Stephen Hemminger <stephen.hemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparc MAC address support should be protected consistently
with CONFIG_SPARC, but there was a stray CONFIG_SPARC64
case.
Bump driver version and release date.
Reported by Andrew Morton.
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Pavel Emelyanov <xemul@openvz.org>
This patch is based on the one from Thomas.
The kauditd_thread() calls the netlink_unicast() and passes
the audit_pid to it. The audit_pid, in turn, is received from
the user space and the tool (I've checked the audit v1.6.9)
uses getpid() to pass one in the kernel. Besides, this tool
doesn't bind the netlink socket to this id, but simply creates
it allowing the kernel to auto-bind one.
That's the preamble.
The problem is that netlink_autobind() _does_not_ guarantees
that the socket will be auto-bound to the current pid. Instead
it uses the current pid as a hint to start looking for a free
id. So, in case of conflict, the audit messages can be sent
to a wrong socket. This can happen (it's unlikely, but can be)
in case some task opens more than one netlink sockets and then
the audit one starts - in this case the audit's pid can be busy
and its socket will be bound to another id.
The proposal is to introduce an audit_nlk_pid in audit subsys,
that will point to the netlink socket to send packets to. It
will most often be equal to audit_pid. The socket id can be
got from the skb's netlink CB right in the audit_receive_msg.
The audit_nlk_pid reset to 0 is not required, since all the
decisions are taken based on audit_pid value only.
Later, if the audit tools will bind the socket themselves, the
kernel will have to provide a way to setup the audit_nlk_pid
as well.
A good side effect of this patch is that audit_pid can later
be converted to struct pid, as it is not longer safe to use
pid_t-s in the presence of pid namespaces. But audit code still
uses the tgid from task_struct in the audit_signal_info and in
the audit_filter_syscall.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit e9720ac ([NET]: Make /proc/net a symlink on /proc/self/net (v3))
broke ganglia and probably other applications that read /proc/net/dev.
This is due to the change of permissions of /proc/net that was
introduced in that commit.
Before: dr-xr-xr-x 5 root root 0 Mar 19 11:30 /proc/net
After: dr-xr--r-- 5 root root 0 Mar 19 11:29 /proc/self/net
This patch restores the permissions to the old value which makes
ganglia happy again.
Pavel Emelyanov says:
This also broke the postfix, as it was reported in bug #10286
and described in detail by Benjamin.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race is SCTP between the loading of the module
and the access by the socket layer to the protocol functions.
In particular, a list of addresss that SCTP maintains is
not initialized prior to the registration with the protosw.
Thus it is possible for a user application to gain access
to SCTP functions before everything has been initialized.
The problem shows up as odd crashes during connection
initializtion when we try to access the SCTP address list.
The solution is to refactor how we do registration and
initialize the lists prior to registering with the protosw.
Care must be taken since the address list initialization
depends on some other pieces of SCTP initialization. Also
the clean-up in case of failure now also needs to be refactored.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Acked-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a rule using ipt_recent is created with a hit count greater than
ip_pkt_list_tot, the rule will never match as it cannot keep track
of enough timestamps. This patch makes ipt_recent refuse to create such
rules.
With ip_pkt_list_tot's default value of 20, the following can be used
to reproduce the problem.
nc -u -l 0.0.0.0 1234 &
for i in `seq 1 100`; do echo $i | nc -w 1 -u 127.0.0.1 1234; done
This limits it to 20 packets:
iptables -A OUTPUT -p udp --dport 1234 -m recent --set --name test \
--rsource
iptables -A OUTPUT -p udp --dport 1234 -m recent --update --seconds \
60 --hitcount 20 --name test --rsource -j DROP
While this is unlimited:
iptables -A OUTPUT -p udp --dport 1234 -m recent --set --name test \
--rsource
iptables -A OUTPUT -p udp --dport 1234 -m recent --update --seconds \
60 --hitcount 21 --name test --rsource -j DROP
With the patch the second rule-set will throw an EINVAL.
Reported-by: Sean Kennedy <skennedy@vcn.com>
Signed-off-by: Daniel Hokka Zakrisson <daniel@hozac.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
logical-bitwise & confusion
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ahci: Add Marvell 6121 SATA support
pata_ali: use atapi_cmd_type() to determine cmd type instead of transfer size
ahci: implement skip_host_reset parameter
ahci: request all PCI BARs
devres: implement pcim_iomap_regions_request_all()
libata-acpi: improve dock event handling
oops and fs corruption; the latter can happen even on valid fs in case of oom.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pata_ali was using qc->nbytes to determine whether a command is
data transfer type or not. As now qc->nbytes can be extended by
padding and draining buffers, these tests are not useful anymore.
Use atapi_cmd_type() instead.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Under certain circumstances (SSP turned off by the BIOS) and for
debugging purposes, skipping global controller reset is helpful. Add
a kernel parameter for it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ahci is often implemented with accompanying SFF compatible interface
and legacy IDE driver may attach to the legacy IO ports when the
controller is already claimed by ahci and vice-versa. This patch
makes ahci use pcim_iomap_regions_request_all() so that all IO regions
are claimed on attach.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some drivers need to reserve all PCI BARs to prevent other drivers
misusing unoccupied BARs. pcim_iomap_regions_request_all() requests
all BARs and iomap specified BARs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve ACPI hotplug handling such that dock event is handled properly.
* Register handlers for dock events.
* Directly detach device on EJECT_REQUEST instead of signaling hotplug
event. This prevents libata from accessing severed controller
and/or device.
* While at it, use named constants for ACPI events and move uevent
signaling inside host lock.
Original patch and testing by Holger Macht.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Holger Macht <hmacht@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use thread number of 1 for 10/100Mbps link instead of 4.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We can't look at the socket to get protocol information. We should
instead look directly at the packet, and hope there are no IPv6
option headers.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
LD drivers/net/built-in.o
WARNING: drivers/net/built-in.o(.text+0x3468): Section mismatch in reference fro
m the function ioc3_probe() to the function .devinit.text:ioc3_serial_probe()
The function ioc3_probe() references
the function __devinit ioc3_serial_probe().
This is often because ioc3_probe lacks a __devinit
annotation or the annotation of ioc3_serial_probe is wrong.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This untested patch _should_ fix:
"(net de2104x) Kernel panic with de2104x tulip driver on boot"
http://bugzilla.kernel.org/show_bug.cgi?id=3156
But the bug submitter isn't responding. Same fix has been applied
to tulip.c (several years ago) and uli526x.c (Feb 2008) drivers.
[ The panic reported in the bug report was removed in a recently
(march 2008) accepted patch from Ondrej Zary. ]
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a critical patch which adds a workaround for a HW bug. The patch
will limit the number of outstanding tx packets to 16. Otherwise, the HW
could send out packets with bad checksums.
The driver will still setup the tx packets into the ring, however, will
only set the Valid bit on 16 packets at a time.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The last change in the Tx queue stop mechanism opens a window
where the Tx queue might be stopped after pending credits
returned.
Tx credits are returned via a control message generated by the HW.
It returns tx credits on demand, triggered by a completion bit
set in selective transmit packet headers.
The current code can lead to the Tx queue stopped
with all pending credits returned, and the current frame
not triggering a credit return. The Tx queue will then never be
awaken.
The driver could alternatively request a completion for packets
that stop the queue. It's however safer at this point to go back
to the pre-existing behaviour.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add "ibm,tah" to the compatible matching table of the ibm_newemac
tah driver. The type "tah" is still preserved for compatibility reasons.
New dts files should use the compatible property though.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch should resolve a problem that's troubled support for
some RNDIS peripherals. It seems to have boiled down to using a
variable to establish transfer size limits before it was assigned,
which caused those devices to fallback to a default "jumbogram"
mode we don't support. Fix by assigning it earlier for RNDIS.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
[ cleanups ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Problem Description and Fix
---------------------------
When a pause packet(with destination as reserved Multicast address) is
received by the EMAC hardware to control the flow of frames being
transmitted by it, it is dropped by the hardware unless the reserved
Multicast address is hashed in to the GAHT[1-4] registers. This code fix
adds the default reserved multicast address to the GAHT[1-4] registers
in the EMAC(s) present on the chip. The flow control with Pause packets
will only work if the following register bits are programmed in EMAC:
EMACx_MR1[APP] = 1
EMACx_RMR[BAE] = 1
EMACx_RMR[MAE] = 1
Behavior that may be observed in a running system
-------------------------------------------------
A host transferring data from a PPC based system may send a Pause packet
to the PPC EMAC requesting it to slow down the flow of packets. If the
default reserved multicast MAC address is not programmed into the
GAHT[1-4] registers this Pause packet will be dropped by PPC EMAC and no
Flow Control will be done.
Signed-off-by: Pravin M. Bathija <pbathija@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There is a race in virtio_net, dealing with disabling/enabling the callback.
I saw the following oops:
kernel BUG at /space/kvm/drivers/virtio/virtio_ring.c:218!
illegal operation: 0001 [#1] SMP
Modules linked in: sunrpc dm_mod
CPU: 2 Not tainted 2.6.25-rc1zlive-host-10623-gd358142-dirty #99
Process swapper (pid: 0, task: 000000000f85a610, ksp: 000000000f873c60)
Krnl PSW : 0404300180000000 00000000002b81a6 (vring_disable_cb+0x16/0x20)
R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:0 CC:3 PM:0 EA:3
Krnl GPRS: 0000000000000001 0000000000000001 0000000010005800 0000000000000001
000000000f3a0900 000000000f85a610 0000000000000000 0000000000000000
0000000000000000 000000000f870000 0000000000000000 0000000000001237
000000000f3a0920 000000000010ff74 00000000002846f6 000000000fa0bcd8
Krnl Code: 00000000002b819a: a7110001 tmll %r1,1
00000000002b819e: a7840004 brc 8,2b81a6
00000000002b81a2: a7f40001 brc 15,2b81a4
>00000000002b81a6: a51b0001 oill %r1,1
00000000002b81aa: 40102000 sth %r1,0(%r2)
00000000002b81ae: 07fe bcr 15,%r14
00000000002b81b0: eb7ff0380024 stmg %r7,%r15,56(%r15)
00000000002b81b6: a7f13e00 tmll %r15,15872
Call Trace:
([<000000000fa0bcd0>] 0xfa0bcd0)
[<00000000002b8350>] vring_interrupt+0x5c/0x6c
[<000000000010ab08>] do_extint+0xb8/0xf0
[<0000000000110716>] ext_no_vtime+0x16/0x1a
[<0000000000107e72>] cpu_idle+0x1c2/0x1e0
The problem can be triggered with a high amount of host->guest traffic.
I think its the following race:
poll says netif_rx_complete
poll calls enable_cb
enable_cb opens the interrupt mask
a new packet comes, an interrupt is triggered----\
enable_cb sees that there is more work |
enable_cb disables the interrupt |
. V
. interrupt is delivered
. skb_recv_done does atomic napi test, ok
some waiting disable_cb is called->check fails->bang!
.
poll would do napi check
poll would do disable_cb
The fix is to let enable_cb not disable the interrupt again, but expect the
caller to do the cleanup if it returns false. In that case, the interrupt is
only disabled, if the napi test_set_bit was successful.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (cleaned up doco)
Add a new poll_controller handler that the netpoll interface needs.
This enables netconsole logging from a kvm guest over the virtio
net interface.
Signed-off-by: Amit Shah <amitshah@gmx.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If the host asks for a huge target towards_target() can overflow, and
we up oops as we try to release more pages than we have. The simple
fix is to use a 64-bit value.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fix up so that the virtio_blk devices in sysfs link correctly to their
block device. This then allows them to be detected by hal, etc
Signed-off-by: Jeremy Katz <katzj@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio-pci acquires its spin lock in an interrupt context so it's necessary
to use spin_lock_irqsave/restore variants. This patch fixes guest SMP when
using virtio devices in KVM.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The variable update_rx is initialized but never used otherwise.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
identifier i;
constant C;
@@
(
extern T i;
|
- T i;
<+... when != i
- i = C;
...+>
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The variable gig is initialized but never used otherwise.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
identifier i;
constant C;
@@
(
extern T i;
|
- T i;
<+... when != i
- i = C;
...+>
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patrick McHardy