Platforms without fences don't have FBC host tracking and those
registers are marked as reserved in those platforms.
v2: checking num_fences to write to FBC fence registers (Ville)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306185833.53984-2-jose.souza@intel.com
i915 can enable aux device nodes for DP MST by calling
drm_dp_mst_connector_late_register()/
drm_dp_mst_connector_early_unregister(),
so let's hook that up.
Changes since v1:
* Call intel_connector_register/unregister() from
intel_dp_mst_connector_late_register/unregister() so we don't lose
error injection - Ville Syrjälä
Changes since v2:
* Don't forget to clean up if intel_connector_register() fails - Ville
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: "Lee, Shawn C" <shawn.c.lee@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310195122.1590925-1-lyude@redhat.com
Some framework test will fail if enable runpm on Vega10.
Disable it untill issue fixed.
Signed-off-by: Feifei Xu <Feifei.Xu@amd.com>
Tested-by: Kyle Chen <Kyle.Chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
and remove each ras IP's own debugfs creation
this is required to fix ras when the driver does not use the drm load
and unload callbacks due to ordering issues with the drm device node.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
centralize all debugfs creation in one place for ras
this is required to fix ras when the driver does not use the drm load
and unload callbacks due to ordering issues with the drm device node.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There will be a coverity warning because min and max are both unsigned.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only kernel bo has kfd eviction fence.
This warning is to give a notice that kfd only remove eviction fence on
individual bos.
Tested-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ALLOC_MEM_FLAGS_* used are the same as the KFD_IOC_ALLOC_MEM_FLAGS_*,
but they are interweavedly used in kernel driver, resulting in bad
readability. For example, KFD_IOC_ALLOC_MEM_FLAGS_COHERENT is not
referenced in kernel, and it functions implicitly in kernel through
ALLOC_MEM_FLAGS_COHERENT, causing unnecessary confusion.
Replace all occurrences of ALLOC_MEM_FLAGS_* with
KFD_IOC_ALLOC_MEM_FLAGS_* to solve the problem.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
People are inclined to think of the previous pr_warn message as an
error, so use pre_debug instead.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If there are no high priority compute queues available then set normal
priority sched array to compute_prio_sched[AMDGPU_GFX_PIPE_PRIO_HIGH]
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We actually expect this to return a 0 on success, or negative error code
on failure. In order to do that, we check whether or not we managed to
write the whole GUID and then return 0 if so, otherwise return a
negative error code. Also, let's add an error message here so it's a
little more obvious when this fails in the middle of a link address
probe.
This should fix issues with certain MST hubs seemingly stopping for no
reason in the middle of the link address probe process.
Fixes: cb897542c6 ("drm/dp_mst: Fix W=1 warnings")
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306234923.547873-3-lyude@redhat.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Noticed this while having some problems with hubs sometimes not being
detected on the first plug. Every single dpcd read or write function
returns the number of bytes transferred on success or a negative error
code, except apparently for drm_dp_mst_dpcd_write() - which returns 0 on
success.
There's not really any good reason for this difference that I can tell,
and having the two functions give differing behavior means that
drm_dp_dpcd_write() will end up returning 0 on success for MST devices,
but the number of bytes transferred for everything else.
So, fix that and update the kernel doc.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: 2f221a5efe ("drm/dp_mst: Add MST support to DP DPCD R/W functions")
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mikita Lipski <mikita.lipski@amd.com>
Cc: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306234923.547873-2-lyude@redhat.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
The currently listed dotclock disagrees with the currently
listed vrefresh rate. Change the dotclock to match the vrefresh.
There are two variants of the COM37H3M panel.
The older one's COM37H3M05DTC data sheet specifies:
MIN TYP MAX
CLK frequency fCLK -- 22.4 26.3 MHz (in VGA mode)
VSYNC Frequency fVSYNC 54 60 66 Hz
VSYNC cycle time tv -- 650 -- H
HSYNC frequency fHSYNC -- 39.3 -- kHz
HSYNC cycle time th -- 570 -- CLK
The newer one's COM37H3M99DTC data sheet says:
MIN TYP MAX
CLK frequency fCLK 18 19.8 27 MHz
VSYNC Frequency fVSYNC 54 60 66 Hz
VSYNC cycle time tv 646 650 700 H
HSYNC frequency fHSYNC -- 39.0 50.0 kHz
HSYNC cycle time th 504 508 630 CLK
So we choose a parameter set that lies within the specs
of both variants. We start at .vrefresh = 60,
choose .htotal = 570 and .vtotal = 650 and end up
in a clock of 22.230 MHz.
Reported-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/e63a0533ad5b5142373437ef758aedbdb716152d.1583826198.git.hns@goldelico.com
Always wait on the start of the signaler request to reduce the problem
of dequeueing the bonded pair too early -- we want both payloads to
start at the same time, with no latency, and yet still allow others to
make full use of the slack in the system. This reduce the amount of time
we spend waiting on the semaphore used to synchronise the start of the
bonded payload.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306133852.3420322-3-chris@chris-wilson.co.uk
In Pete Goodliffe words, "You can improve a system by adding new code. You
can also improve a system by removing code" - In this case, commit
"202b52b7fbf70" added new code to initialize end of the node. So, there
is no need for duplicated initialization, and this patch simply removes it.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200309151156.25040-1-akeem.g.abodunrin@intel.com
This patch adds support for the YUV420 output from the Amlogic Meson SoCs
Video Processing Unit to the HDMI Controller.
The YUV420 is obtained by generating a YUV444 pixel stream like
the classic HDMI display modes, but then the Video Encoder output
can be configured to down-sample the YUV444 pixel stream to a YUV420
stream.
In addition if pixel stream down-sampling, the Y Cb Cr components must
also be mapped differently to align with the HDMI2.0 specifications.
This mode needs a different clock generation scheme since the TMDS PHY
clock must match the 10x ratio with the YUV420 pixel clock, but
the video encoder must run at 2x the pixel clock.
This patch enables the bridge bus format negociation, and handles
the YUV420 case if selected by the negociation.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-12-narmstrong@baylibre.com
This patch adds clocking support for the YUV420 output from the
Amlogic Meson SoCs Video Processing Unit to the HDMI Controller.
The YUV420 is obtained by generating a YUV444 pixel stream like
the classic HDMI display modes, but then the Video Encoder output
can be configured to down-sample the YUV444 pixel stream to a YUV420
stream.
This mode needs a different clock generation scheme since the TMDS PHY
clock must match the 10x ratio with the YUV420 pixel clock, but
the video encoder must run at 2x the pixel clock.
This patch adds the TMDS PHY clock value in all the video clock setup
in order to better support these specific uses cases and switch
to the Common Clock framework for clocks handling in the future.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-11-narmstrong@baylibre.com
This patch adds encoding support for the YUV420 output from the
Amlogic Meson SoCs Video Processing Unit to the HDMI Controller.
The YUV420 is obtained by generating a YUV444 pixel stream like
the classic HDMI display modes, but then the Video Encoder output
can be configured to down-sample the YUV444 pixel stream to a YUV420
stream.
In addition if pixel stream down-sampling, the Y Cb Cr components must
also be mapped differently to align with the HDMI2.0 specifications.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-10-narmstrong@baylibre.com
To allow using formats from negotiation, stop enforcing input_bus_format
in the private dw-plat-data struct.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-9-narmstrong@baylibre.com
Switch the dw-hdmi driver to drm_bridge_funcs by implementing a new local
bridge, connecting it to the dw-hdmi bridge, then implement the
atomic_get_input_bus_fmts/atomic_get_output_bus_fmts.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-8-narmstrong@baylibre.com
Before switching to bridge funcs, make sure drm_display_mode is passed
as const to the venc functions.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-7-narmstrong@baylibre.com
Now the DW-HDMI Controller supports the HDMI2.0 modes, enable support
for these modes in the connector if the platform supports them.
We limit these modes to DW-HDMI IP version >= 0x200a which
are designed to support HDMI2.0 display modes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-6-narmstrong@baylibre.com
Add the atomic_get_output_bus_fmts, atomic_get_input_bus_fmts to negociate
the possible output and input formats for the current mode and monitor,
and use the negotiated formats in a basic atomic_check callback.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-5-narmstrong@baylibre.com
Add the max_bpc property to the dw-hdmi connector to prepare support
for 10, 12 & 16bit output support.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-3-narmstrong@baylibre.com
gmbus/aux may be clocked by cdclk, thus we should make sure no
transfers are ongoing while the cdclk frequency is being changed.
We do that by simply grabbing all the gmbus/aux mutexes. No one
else should be holding any more than one of those at a time so
the lock ordering here shouldn't matter.
v2: Use mutex_lock_nest_lock() (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200302174442.5803-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The low level read_lut() functions don't need the entire crtc state
as they know exactly what they're reading. Just need to pass in the
crtc to get at the pipe. This now neatly mirrors the load_lut()
direction.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303173313.28117-10-ville.syrjala@linux.intel.com
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
PIPEGCMAX is a 11.6 (or 1.16 if you will) value. Ie. it can
represent a value of 1.0 when the maximum we can store in the
software LUT is 0.ffff. Clamp the value so that it gets
saturated to the max the uapi supports.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303173313.28117-9-ville.syrjala@linux.intel.com
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
A variable called 'i' having an unsigned type is just looking for
trouble, and using a sized type generally makes no sense either.
Change all of them to just plain old int. And do the same for some
'lut_size' variables which generally provide the loop end codition
for 'i'.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303173313.28117-7-ville.syrjala@linux.intel.com
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
Only load the CGM CSC based on the cgm_mode bit like we
do with the gamma/degamma LUTs. And make the function
naming and arguments consistent as well.
TODO: the code to convert the coefficients look totally
bogus. IIRC CHV uses two's complement format but the code
certainly doesn't generate that, so probably negative
coefficients are totally busted.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303173313.28117-2-ville.syrjala@linux.intel.com
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
During i915_request_retire() we decouple the i915_request.hwsp_seqno
from the intel_timeline so that it may be freed before the request is
released. However, we need to warn the compiler that the pointer may
update under its nose.
[ 171.438899] BUG: KCSAN: data-race in i915_request_await_dma_fence [i915] / i915_request_retire [i915]
[ 171.438920]
[ 171.438932] write to 0xffff8881e7e28ce0 of 8 bytes by task 148 on cpu 2:
[ 171.439174] i915_request_retire+0x1ea/0x660 [i915]
[ 171.439408] retire_requests+0x7a/0xd0 [i915]
[ 171.439640] engine_retire+0xa1/0xe0 [i915]
[ 171.439657] process_one_work+0x3b1/0x690
[ 171.439671] worker_thread+0x80/0x670
[ 171.439685] kthread+0x19a/0x1e0
[ 171.439701] ret_from_fork+0x1f/0x30
[ 171.439721]
[ 171.439739] read to 0xffff8881e7e28ce0 of 8 bytes by task 696 on cpu 1:
[ 171.439990] i915_request_await_dma_fence+0x162/0x520 [i915]
[ 171.440230] i915_request_await_object+0x2fe/0x470 [i915]
[ 171.440467] i915_gem_do_execbuffer+0x45dc/0x4c20 [i915]
[ 171.440704] i915_gem_execbuffer2_ioctl+0x2c3/0x580 [i915]
[ 171.440722] drm_ioctl_kernel+0xe4/0x120
[ 171.440736] drm_ioctl+0x297/0x4c7
[ 171.440750] ksys_ioctl+0x89/0xb0
[ 171.440766] __x64_sys_ioctl+0x42/0x60
[ 171.440788] do_syscall_64+0x6e/0x2c0
[ 171.440802] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200309110934.868-1-chris@chris-wilson.co.uk
AMDGPU statically sets priority for compute queues
at initialization so remove all the functions
responsible for changing compute queue priority dynamically.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Switch to appropriate sched list for an entity on priority override.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Implement drm_sched_entity_modify_sched() which modifies existing
sched_list with a different one. This is going to be helpful when
userspace changes priority of a ctx/entity then the driver can switch
to the corresponding HW scheduler list for that priority.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We were changing compute ring priority while rings were being used
before every job submission which is not recommended. This patch
sets compute queue priority at mqd initialization for gfx8, gfx9 and
gfx10.
Policy: make queue 0 of each pipe as high priority compute queue
High/normal priority compute sched lists are generated from set of high/normal
priority compute queues. At context creation, entity of compute queue
get a sched list from high or normal priority depending on ctx->priority
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Radhakrishna Sripada