On BE3-R, the PF programs the initial MAC address for its VFs. Doing it again
in VF probe, causes a FW error which although harmless generates
an unnecessary error log message.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not being set currently. (This field is not applicable for Lancer)
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupts need to be enabled in be_resume, when adapter boots back up from D3cold.
disabling interrupts in be_suspend() just to be symmetric to be_resume().
Signed-off-by: Ravikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the VIF thread is still running after unbinding the Tx and Rx IRQs
in xenvif_disconnect(), the thread may attempt to raise an event which
will BUG (as the irq is unbound).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2013-11-21
Please pull this batch of fixes intended for the 3.13 stream!
For the Bluetooth bits, Gustavo says:
"A few fixes for 3.13. There is 3 fixes to the RFCOMM protocol. One
crash fix to L2CAP. A simple fix to a bad behaviour in the SMP
protocol."
On top of that...
Amitkumar Karwar sends a quintet of mwifiex fixes -- two fixes related
to failure handling, two memory leak fixes, and a NULL pointer fix.
Felix Fietkau corrects and earlier rt2x00 HT descriptor handling fix
to address a crash.
Geyslan G. Bem fixes a memory leak in brcmfmac.
Larry Finger address more pointer arithmetic errors in rtlwifi.
Luis R. Rodriguez provides a regulatory fix in the shared ath code.
Sujith Manoharan brings a couple ath9k initialization fixes.
Ujjal Roy offers one more mwifiex fix to avoid invalid memory accesses
when unloading the USB driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add auto-MDI/MDI-X capability for forced (autonegotiation disabled)
10/100 Mbps speeds on Vitesse VSC82x4 PHYs. Exported previously static
function genphy_setup_forced() required by the new config_aneg handler
in the Vitesse PHY module.
Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitesse VSC8662 is Dual Port 10/100/1000Base-T Phy
Its register set and features are similar to other Vitesse Phys.
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC8574 is a quad-port Gigabit Ethernet transceiver with four SerDes
interfaces for quad-port dual media capability.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shruti Kanetkar <Shruti@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitesse VSC8234 is quad port 10/100/1000BASE-T PHY
with SGMII and SERDES MAC interfaces.
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Shruti Kanetkar <Shruti@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch now always passes msg->msg_namelen as 0. recvmsg handlers must
set msg_namelen to the proper size <= sizeof(struct sockaddr_storage)
to return msg_name to the user.
This prevents numerous uninitialized memory leaks we had in the
recvmsg handlers and makes it harder for new code to accidentally leak
uninitialized memory.
Optimize for the case recvfrom is called with NULL as address. We don't
need to copy the address at all, so set it to NULL before invoking the
recvmsg handler. We can do so, because all the recvmsg handlers must
cope with the case a plain read() is called on them. read() also sets
msg_name to NULL.
Also document these changes in include/linux/net.h as suggested by David
Miller.
Changes since RFC:
Set msg->msg_name = NULL if user specified a NULL in msg_name but had a
non-null msg_namelen in verify_iovec/verify_compat_iovec. This doesn't
affect sendto as it would bail out earlier while trying to copy-in the
address. It also more naturally reflects the logic by the callers of
verify_iovec.
With this change in place I could remove "
if (!uaddr || msg_sys->msg_namelen == 0)
msg->msg_name = NULL
".
This change does not alter the user visible error logic as we ignore
msg_namelen as long as msg_name is NULL.
Also remove two unnecessary curly brackets in ___sys_recvmsg and change
comments to netdev style.
Cc: David Miller <davem@davemloft.net>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data from the hardware should be little endian. Correct the
declaration.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum packet number which a tx aggregation buffer could contain
is the tx_qlen.
tx_qlen = buffer size / (packet size + descriptor size).
If the tx buffer is empty and the queued packets are more than the
maximum value which is defined above, stop the tx queue. Wake the
tx queue if tx queue is stopped and the queued packets are less than
tx_qlen.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the code for sending the packet in the rtl8152_start_xmit().
Let rtl8152_start_xmit() to queue the packet only, and schedule a
tasklet to send the queued packets. This simplify the code and make
sure all the packet would be sent by the original order.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx/rx would access the memory which is out of the desired range.
Modify the method of checking the end of the memory to avoid it.
For r8152_tx_agg_fill(), the variable remain may become negative.
However, the declaration is unsigned, so the while loop wouldn't
break when reaching the end of the desied memory. Although to change
the declaration from unsigned to signed is enough to fix it, I also
modify the checking method for safe. Replace
remain = rx_buf_sz - sizeof(*tx_desc) -
(u32)((void *)tx_data - agg->head);
with
remain = rx_buf_sz - (int)(tx_agg_align(tx_data) - agg->head);
to make sure the variable remain is always positive. Then, the
overflow wouldn't happen.
For rx_bottom(), the rx_desc should not be used to calculate the
packet length before making sure the rx_desc is in the desired range.
Change the checking to two parts. First, check the descriptor is in
the memory. The other, using the descriptor to find out the packet
length and check if the packet is in the memory.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Mostly these are fixes for fallout due to merge window changes, as
well as cures for problems that have been with us for a much longer
period of time"
1) Johannes Berg noticed two major deficiencies in our genetlink
registration. Some genetlink protocols we passing in constant
counts for their ops array rather than something like
ARRAY_SIZE(ops) or similar. Also, some genetlink protocols were
using fixed IDs for their multicast groups.
We have to retain these fixed IDs to keep existing userland tools
working, but reserve them so that other multicast groups used by
other protocols can not possibly conflict.
In dealing with these two problems, we actually now use less state
management for genetlink operations and multicast groups.
2) When configuring interface hardware timestamping, fix several
drivers that simply do not validate that the hwtstamp_config value
is one the driver actually supports. From Ben Hutchings.
3) Invalid memory references in mwifiex driver, from Amitkumar Karwar.
4) In dev_forward_skb(), set the skb->protocol in the right order
relative to skb_scrub_packet(). From Alexei Starovoitov.
5) Bridge erroneously fails to use the proper wrapper functions to make
calls to netdev_ops->ndo_vlan_rx_{add,kill}_vid. Fix from Toshiaki
Makita.
6) When detaching a bridge port, make sure to flush all VLAN IDs to
prevent them from leaking, also from Toshiaki Makita.
7) Put in a compromise for TCP Small Queues so that deep queued devices
that delay TX reclaim non-trivially don't have such a performance
decrease. One particularly problematic area is 802.11 AMPDU in
wireless. From Eric Dumazet.
8) Fix crashes in tcp_fastopen_cache_get(), we can see NULL socket dsts
here. Fix from Eric Dumzaet, reported by Dave Jones.
9) Fix use after free in ipv6 SIT driver, from Willem de Bruijn.
10) When computing mergeable buffer sizes, virtio-net fails to take the
virtio-net header into account. From Michael Dalton.
11) Fix seqlock deadlock in ip4_datagram_connect() wrt. statistic
bumping, this one has been with us for a while. From Eric Dumazet.
12) Fix NULL deref in the new TIPC fragmentation handling, from Erik
Hugne.
13) 6lowpan bit used for traffic classification was wrong, from Jukka
Rissanen.
14) macvlan has the same issue as normal vlans did wrt. propagating LRO
disabling down to the real device, fix it the same way. From Michal
Kubecek.
15) CPSW driver needs to soft reset all slaves during suspend, from
Daniel Mack.
16) Fix small frame pacing in FQ packet scheduler, from Eric Dumazet.
17) The xen-netfront RX buffer refill timer isn't properly scheduled on
partial RX allocation success, from Ma JieYue.
18) When ipv6 ping protocol support was added, the AF_INET6 protocol
initialization cleanup path on failure was borked a little. Fix
from Vlad Yasevich.
19) If a socket disconnects during a read/recvmsg/recvfrom/etc that
blocks we can do the wrong thing with the msg_name we write back to
userspace. From Hannes Frederic Sowa. There is another fix in the
works from Hannes which will prevent future problems of this nature.
20) Fix route leak in VTI tunnel transmit, from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
genetlink: make multicast groups const, prevent abuse
genetlink: pass family to functions using groups
genetlink: add and use genl_set_err()
genetlink: remove family pointer from genl_multicast_group
genetlink: remove genl_unregister_mc_group()
hsr: don't call genl_unregister_mc_group()
quota/genetlink: use proper genetlink multicast APIs
drop_monitor/genetlink: use proper genetlink multicast APIs
genetlink: only pass array to genl_register_family_with_ops()
tcp: don't update snd_nxt, when a socket is switched from repair mode
atm: idt77252: fix dev refcnt leak
xfrm: Release dst if this dst is improper for vti tunnel
netlink: fix documentation typo in netlink_set_err()
be2net: Delete secondary unicast MAC addresses during be_close
be2net: Fix unconditional enabling of Rx interface options
net, virtio_net: replace the magic value
ping: prevent NULL pointer dereference on write to msg_name
bnx2x: Prevent "timeout waiting for state X"
bnx2x: prevent CFC attention
bnx2x: Prevent panic during DMAE timeout
...
Register generic netlink multicast groups as an array with
the family and give them contiguous group IDs. Then instead
of passing the global group ID to the various functions that
send messages, pass the ID relative to the family - for most
families that's just 0 because the only have one group.
This avoids the list_head and ID in each group, adding a new
field for the mcast group ID offset to the family.
At the same time, this allows us to prevent abusing groups
again like the quota and dropmon code did, since we can now
check that a family only uses a group it owns.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This doesn't really change anything, but prepares for the
next patch that will change the APIs to pass the group ID
within the family, rather than the global group ID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by David Miller, make genl_register_family_with_ops()
a macro and pass only the array, evaluating ARRAY_SIZE() in the
macro, this is a little safer.
The openvswitch has some indirection, assing ops/n_ops directly in
that code. This might ultimately just assign the pointers in the
family initializations, saving the struct genl_family_and_ops and
code (once mcast groups are handled differently.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Re-enable flow steering verbs with new improved userspace ABI
- Fixes for slow connection due to GID lookup scalability
- IPoIB fixes
- Many fixes to HW drivers including mlx4, mlx5, ocrdma and qib
- Further improvements to SRP error handling
- Add new transport type for Cisco usNIC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=xxC+
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
- Re-enable flow steering verbs with new improved userspace ABI
- Fixes for slow connection due to GID lookup scalability
- IPoIB fixes
- Many fixes to HW drivers including mlx4, mlx5, ocrdma and qib
- Further improvements to SRP error handling
- Add new transport type for Cisco usNIC
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (66 commits)
IB/core: Re-enable create_flow/destroy_flow uverbs
IB/core: extended command: an improved infrastructure for uverbs commands
IB/core: Remove ib_uverbs_flow_spec structure from userspace
IB/core: Use a common header for uverbs flow_specs
IB/core: Make uverbs flow structure use names like verbs ones
IB/core: Rename 'flow' structs to match other uverbs structs
IB/core: clarify overflow/underflow checks on ib_create/destroy_flow
IB/ucma: Convert use of typedef ctl_table to struct ctl_table
IB/cm: Convert to using idr_alloc_cyclic()
IB/mlx5: Fix page shift in create CQ for userspace
IB/mlx4: Fix device max capabilities check
IB/mlx5: Fix list_del of empty list
IB/mlx5: Remove dead code
IB/core: Encorce MR access rights rules on kernel consumers
IB/mlx4: Fix endless loop in resize CQ
RDMA/cma: Remove unused argument and minor dead code
RDMA/ucma: Discard events for IDs not yet claimed by user space
IB/core: Add Cisco usNIC rdma node and transport types
RDMA/nes: Remove self-assignment from nes_query_qp()
IB/srp: Report receive errors correctly
...
Secondary unicast MAC addresses will get deleted only when the interface is UP.
When the interface is DOWN, though these secondary MAC addresses are unusable
and awaiting to be deleted, cause the firmware to believe that they are being used.
If the user intends to set a MAC address as primary MAC from one of these
secondary MAC addresses, the firmware returns a MAC address Collision error.
Delete these secondary MAC addresses during be_close.
The secondary MAC addresses list will be refreshed during interface open anyway.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently requests the firmware to enable rx_interface options
without considering if the interface was created with that capability.
This could cause commands to firmware to fail.
To avoid this, enable only those options on an interface if the interface
was created with that capability.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is more appropriate to use # of queue pairs currently used by
the driver instead of a magic value.
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver release rtnl lock in between DCB re-configuration.
As a result, other flows (e.g., mtu config) may enter in between and fail
due to halted tx path for dcb configuration.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During VF load, prior to sending messages on HW channel to PF the VF
checks its bulletin board to see whether the PF indicated it has closed;
If a closed PF is encountered, the VF skips sending the message.
Due to incorrect return values, there's a possible scenario in which the VF
finishes loading "successfully", while the PF hasn't actually fully configured
FW/HW for the VFs supposed configuration.
Once VF tries to send Tx packets, HW will raise an attention (and FW possibly
will start treat the VF as malicious).
The patch fails the loading process in such a scenario.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If chip enters a recovery flow just after the driver issues a DMAE request
the DMAE will timeout. Current code will cause a bnx2x_panic() as a result,
which means interface will no longer be usable (regardless of the recovery
results), as bnx2x_panic() is irreversible for the driver.
As this is a possible flow, the panic should be reached only when driver
is compiled with STOP_ON_ERROR.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While unloading, bnx2x needs to clean the sp_rtnl_state to prevent
configuration made before the unload to be applied afterwards with
stale values.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free temporary 'chanspecs' avoiding leakage.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a bug in xennet_alloc_rx_buffers, when allocating page or
sk_buff failed, and at the same time rx_batch queue not empty,
the rx_refill_timer timer won't be scheduled. If finally the remaining
request buffers in rx ring less than what backend driver expected,
the backend driver would think of rx ring as full and start dropping packets.
In such situation, there is no way for the netfront driver to recover
automatically, so that the device can not work properly.
The patch fixes the problem by always scheduling rx_refill_timer timer when
alloc_page or __netdev_alloc_skb fails, no matter whether rx_batch queue is
empty or not. It ensures that the rx ring request buffers will finally meet
the backend needs.
Signed-off-by: Ma JieYue <jieyue.majy@alibaba-inc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
During resume, use for_each_slave to walk the slaves of the cpsw, and
soft-reset each of them. This prevents oopses if there is only one
slave configured.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I met a Bug when I add ip target with the wrong ip address:
echo +500.500.500.500 > /sys/class/net/bond0/bonding/arp_ip_target
the wrong ip address will transfor to 245.245.245.244 and add
to the ip target success, it is uncorrect, so I add checks to avoid
adding wrong address.
The in4_pton() will set wrong ip address to 0.0.0.0, it will return by
the next check and will not add to ip target.
v2
According Veaceslav's opinion, simplify the code.
v3
According Veaceslav's opinion, add broadcast check and make a micro
definition to package it.
v4
Solve the problem of the format which David point out.
Suggested-by: Veaceslav Falico <vfalico@redhat.com>
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For archs with pages size of 4K, when the chunk is freed, fwp is not in the
list so avoid attempting to delete it.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This driver uses a number of macros to get and set various fields in the
RX and TX descriptors. To work correctly, a u8 pointer to the descriptor
must be used; however, in some cases a descriptor structure pointer is used
instead. In addition, a duplicated statement is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) After driver load failure, clear 'card->adapter' instead of
card pointer so that card specific cleanup is performed later
when user unloads the driver.
2) Clear usb_card pointer in disconnect handler to avoid invalid
memory access when user unloads the driver after removing the
card.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When driver is failed to load, card pointer doesn't get
freed. We will free it in cleanup handler which is called
in failure as well as unload path.
Also, update drvdata in init/cleanup handlers instead of
register/unregister handlers.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) Currently we freeing wdev for each interface in driver unload
path. We may leak memory if user have already deleted an interface.
mwifiex_add_virtual_intf() allocates wdev structure. So it should
be freed in mwifiex_del_virtual_intf().
This will make sure that wdev will be freed when user deletes an
interface and also in unload path.
2) "priv->netdev->ieee80211_ptr" should also be cleared in
mwifiex_del_virtual_intf.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need to free/unregister wiphy when
mwifiex_register_cfg80211() fails. The routine internally takes
care of it. This redundant code can cause NULL pointer dereference,
for adapter->wiphy.
Reported-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) If register_netdevice() is failed, we are freeing netdev
pointer, but priv->netdev is not cleared. This gives kernel
paging request error when driver is unloaded or interface is
deleted. Fix the problem by clearing the pointer.
2) Fix memory leak issue by freeing 'wdev' in failure paths.
Also, clear priv->wdev pointer.
As mwifiex_add_virtual_intf() successfully handles the
failure conditions, redundant code under err_add_intf label
is removed in this patch.
Reported-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex_add_virtual_intf() returns ERR_PTR values. So use IS_ERR()
macro instead of checking for NULL pointer.
Reported-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "rt2x00: fix HT TX descriptor settings regression"
assumes that the control parameter to rt2x00mac_tx is always non-NULL.
There is an internal call in rt2x00lib_bc_buffer_iter where NULL is
passed. Fix the resulting crash by adding an initialized dummy on-stack
ieee80211_tx_control struct.
Cc: stable@vger.kernel.org # 3.7+
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some boards which are based on AR9300, AR9580 or
AR9550, MCS15 usage is problematic.
This is because these boards use a "frequency doubler",
which doubles the refclk to get better EVM, but causes
spurs. Handle this properly in the driver to recover
throughput.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A world regulatory domain check was in place that
prevents user dynamic regulatory hints from being
processed. This was there for historical reasons
as this was only possible previously for world
roaming cards and dynamic regulatory settings was
only possible for country IEs. Fix this by enforcing
the world regulatory domain check only for when the
initiator is a country IE. Support for dynamic user
regulatory support is already checked.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
some robustness fixes for broken virtio devices, plus minor tweaks.
[vs last pull request: added the virtio-scsi broken vq escape patch, which
I somehow lost.]
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJSgDsJAAoJENkgDmzRrbjxEE4P/jXqZHS/HdlxW9k0BjKKlEIF
PdtCoP3UhWTdskXvy2pD8m6nYn214MEJYUIa4HFlIEZsdxhuexzQHY19Ynkjagyv
57sRsUUm5fYQLIL7IUh2DUD1VU38hUFinno/y333szzvCj9qITDA/QABsiWxK8NO
dq+Lmeixgrhc5yN9iryW+gZV+hekJIZ4LsU5ejSaJucKblzXUH8qIbmSthG7RTYJ
tr4J7xTTXbhxY4CoC5Dpx2hvsFkvzaAIvI4Nr1mDjfq5cR8BaYvnC89U1IbhdAey
p1AbZE58JLrY+Z8K8LBRGV2KjO8qSZ6R47hbZ9nAnodJYB7sZLyj6jUe1q+/htuC
Dh9Xm9O4eW2xNaFk20dYeIF4UU5/HzdsbvG/IlH8x4sm8/K706ocYyAOHlzYUg2T
k7gltrgDzDokMgb2R44gwnr4oaJ2q8Gne6JXswlPEv2eRs6vNnA5Xhc0rEHGkU6C
gYn1vNFN6yx0vf2syG/Ce5pZtMxGpefKQkHzzWdq8FKr1B9s54dDuf2hls7J8A9t
OQT1gE33yURSelf4Kh4k9zWXaWk/Ohv9l2R1cqpALnJ4/+q0fP5t7HdK500S7aax
DxLeFeqvsBw7nlWgsGxQmt+fjITQFHhcDiwst0ehnt6RbDEW7XPIguz0K/gyhxYG
+UNbl/5Gr64jnUX3YCzm
=vY2L
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"Nothing really exciting: some groundwork for changing virtio endian,
and some robustness fixes for broken virtio devices, plus minor
tweaks"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_scsi: verify if queue is broken after virtqueue_get_buf()
x86, asmlinkage, lguest: Pass in globals into assembler statement
virtio: mmio: fix signature checking for BE guests
virtio_ring: adapt to notify() returning bool
virtio_net: verify if queue is broken after virtqueue_get_buf()
virtio_console: verify if queue is broken after virtqueue_get_buf()
virtio_blk: verify if queue is broken after virtqueue_get_buf()
virtio_ring: add new function virtqueue_is_broken()
virtio_test: verify if virtqueue_kick() succeeded
virtio_net: verify if virtqueue_kick() succeeded
virtio_ring: let virtqueue_{kick()/notify()} return a bool
virtio_ring: change host notification API
virtio_config: remove virtio_config_val
virtio: use size-based config accessors.
virtio_config: introduce size-based accessors.
virtio_ring: plug kmemleak false positive.
virtio: pm: use CONFIG_PM_SLEEP instead of CONFIG_PM
This patch enhances the type safety for the kfifo API. It is now safe
to put const data into a non const FIFO and the API will now generate a
compiler warning when reading from the fifo where the destination
address is pointing to a const variable.
As a side effect the kfifo_put() does now expect the value of an element
instead a pointer to the element. This was suggested Russell King. It
make the handling of the kfifo_put easier since there is no need to
create a helper variable for getting the address of a pointer or to pass
integers of different sizes.
IMHO the API break is okay, since there are currently only six users of
kfifo_put().
The code is also cleaner by kicking out the "if (0)" expressions.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
John W. Linville says:
====================
pull request: wireless 2013-11-14
Please pull this batch of fixes intended for the 3.13 stream!
Amitkumar Karwar offers a quartet of mwifiex fixes, including an
endian fix and three fixes for invalid memory access.
Avinash Patil trims the packet length value for packets received from
an SDIO interface.
Colin Ian King fixes a NULL pointer dereference in the rtlwifi
efuse code.
Dan Carpenter cleans-up an mwifiex integer underflow, a potential
libertas oops, a memory corrupion bug in wcn36xx, and a locking issue
also in wcn36xx.
Dan Williams helps prism54 devices to avoid being misclassified as
Ethernet devices.
Felipe Pena fixes a couple of typo errors, one in rt2x00 and the
other in rtlwifi.
Janusz Dziedzic corrects a pair of DFS-related problems in ath9k.
Larry Finger patches three rtlwifi drivers to correctly report signal
strength even for an unassociated AP.
Mark Cave-Ayland rewrites some endian-illiterate packet type extraction
code in rtlwifi.
Stanislaw Gruszka addresses an rt2x00 regression related to setting
HT station WCID and AMPDU density parameters.
Sujith Manoharan corrects the initvals settings for AR9485.
Ujjal Roy patches an obscure bit of code in mwifiex that was using
the wrong definition of eth_hdr when briding patches in AP mode.
Wei Yongjun fixes a couple of bugs: one is a return code handling
bug in libertas; and, the other is a locking issue in wcn36xx.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2613af0ed1 ("virtio_net: migrate mergeable rx buffers to page
frag allocators") changed the mergeable receive buffer size from PAGE_SIZE
to MTU-size. However, the merge buffer size does not take into account the
size of the virtio-net header. Consequently, packets that are MTU-size
will take two buffers intead of one (to store the virtio-net header),
substantially decreasing the throughput of MTU-size traffic due to TCP
window / SKB truesize effects.
This commit changes the mergeable buffer size to include the virtio-net
header. The buffer size is cacheline-aligned because skb_page_frag_refill
will not automatically align the requested size.
Benchmarks taken from an average of 5 netperf 30-second TCP_STREAM runs
between two QEMU VMs on a single physical machine. Each VM has two VCPUs and
vhost enabled. All VMs and vhost threads run in a single 4 CPU cgroup
cpuset, using cgroups to ensure that other processes in the system will not
be scheduled on the benchmark CPUs. Transmit offloads and mergeable receive
buffers are enabled, but guest_tso4 / guest_csum are explicitly disabled to
force MTU-sized packets on the receiver.
next-net trunk before 2613af0ed1 (PAGE_SIZE buf): 3861.08Gb/s
net-next trunk (MTU 1500- packet uses two buf due to size bug): 4076.62Gb/s
net-next trunk (MTU 1480- packet fits in one buf): 6301.34Gb/s
net-next trunk w/ size fix (MTU 1500 - packet fits in one buf): 6445.44Gb/s
Suggested-by: Eric Northup <digitaleric@google.com>
Signed-off-by: Michael Dalton <mwdalton@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes bug 62491 (https://bugzilla.kernel.org/show_bug.cgi?id=62491).
After resuming some users got the following error flooding the kernel log:
alx 0000:02:00.0: invalid PHY speed/duplex: 0xffff
Signed-off-by: Jonas Hahnfeld <linux@hahnjo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde