We have suffered recrusive frozen PE a lot, which was caused
by IO accesses during the PE reset. Ben came up with the good
idea to keep frozen PE until recovery (BAR restore) gets done.
With that, IO accesses during PE reset are dropped by hardware
and wouldn't incur the recrusive frozen PE any more.
The patch implements the idea. We don't clear the frozen state
until PE reset is done completely. During the period, the EEH
core expects unfrozen state from backend to keep going. So we
have to reuse EEH_PE_RESET flag, which has been set during PE
reset, to return normal state from backend. The side effect is
we have to clear frozen state for towice (PE reset and clear it
explicitly), but that's harmless.
We have some limitations on pHyp. pHyp doesn't allow to enable
IO or DMA for unfrozen PE. So we don't enable them on unfrozen PE
in eeh_pci_enable(). We have to enable IO before grabbing logs on
pHyp. Otherwise, 0xFF's is always returned from PCI config space.
Also, we had wrong return value from eeh_pci_enable() for
EEH_OPT_THAW_DMA case. The patch fixes it too.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For EEH PowerNV backends, they need use their own PCI config
accesors as the normal one could be blocked during PE reset.
The patch also removes necessary parameter "hose" for the
function ioda_eeh_bridge_reset().
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We've observed multiple PE reset failures because of PCI-CFG
access during that period. Potentially, some device drivers
can't support EEH very well and they can't put the device to
motionless state before PE reset. So those device drivers might
produce PCI-CFG accesses during PE reset. Also, we could have
PCI-CFG access from user space (e.g. "lspci"). Since access to
frozen PE should return 0xFF's, we can block PCI-CFG access
during the period of PE reset so that we won't get recrusive EEH
errors.
The patch adds flag EEH_PE_RESET, which is kept during PE reset.
The PowerNV/pSeries PCI-CFG accessors reuse the flag to block
PCI-CFG accordingly.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For some fields (e.g. LEM, MMIO, DMA) in PHB diag-data dump, it's
meaningless to print them if they have non-zero value in the
corresponding mask registers because we always have non-zero values
in the mask registers. The patch only prints those fieds if we
have non-zero values in the primary registers (e.g. LEM, MMIO, DMA
status) so that we can save couple of lines. The patch also removes
unnecessary spare line before "brdgCtl:" and two leading spaces as
prefix in each line as Ben suggested.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The flag PNV_EEH_STATE_ENABLED is put into pnv_phb::eeh_state,
which is protected by CONFIG_EEH. We needn't that. Instead, we
can have pnv_phb::flags and maintain all flags there, which is
the purpose of the patch. The patch also renames PNV_EEH_STATE_ENABLED
to PNV_PHB_FLAG_EEH.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PHB state PNV_EEH_STATE_REMOVED maintained in pnv_phb isn't
so useful any more and it's duplicated to EEH_PE_ISOLATED. The
patch replaces PNV_EEH_STATE_REMOVED with EEH_PE_ISOLATED.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Up until now we have been setting the runlatch bits for a busy CPU and
clearing it when a CPU enters idle state. The runlatch bit has thus
been consistent with the utilization of a CPU as long as the CPU is online.
However when a CPU is hotplugged out the runlatch bit is not cleared. It
needs to be cleared to indicate an unused CPU. Hence this patch has the
runlatch bit cleared for an offline CPU just before entering an idle state
and sets it immediately after it exits the idle state.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have two copies of code that creates an OPAL sg list. Consolidate
these into a common set of helpers and fix the endian issues.
The flash interface embedded a version number in the num_entries
field, whereas the dump interface did did not. Since versioning
wasn't added to the flash interface and it is impossible to add
this in a backwards compatible way, just remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix little endian issues with the OPAL error log code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The bitmap in opal_poll_events and opal_handle_interrupt is
big endian, so we need to byteswap it on little endian builds.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Using size_t in our APIs is asking for trouble, especially
when some OPAL calls use size_t pointers.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On PowerNV platform, we are holding an unnecessary refcount on a pci_dev, which
leads to the pci_dev is not destroyed when hotplugging a pci device.
This patch release the unnecessary refcount.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With this patch I was able to update firmware on an LE kernel.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a subtle race when sending CPUs back to OPAL on kexec.
We mark them as "in real mode" right before we send them down. Once
we've booted the new kernel, it might try to call opal_reinit_cpus()
to change endianness, and that requires all CPUs to be spinning inside
OPAL.
However there is no synchronization here and we've observed cases
where the returning CPUs hadn't established their new state inside
OPAL before opal_reinit_cpus() is called, causing it to fail.
The proper fix is to actually wait for them to go down all the way
from the kexec'ing kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The size of the sysparam sysfs files is determined from the device tree
at boot. However the buffer is hard coded to 64 bytes. If we encounter a
parameter that is larger than 64, or miss-parse the device tree, the
buffer will overflow when reading or writing to the parameter.
Check it at discovery time, and if the parameter is too large, do not
create a sysfs entry for it.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The sysparam code currently uses the userspace supplied number of
bytes when memcpy()ing in to a local 64-byte buffer.
Limit the maximum number of bytes by the size of the buffer.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The OPAL calls are returning int64_t values, which the sysparam code
stores in an int, and the sysfs callback returns ssize_t. Make code a
easier to read by consistently using ssize_t.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When a sysparam query in OPAL returned a negative value (error code),
sysfs would spew out a decent chunk of memory; almost 64K more than
expected. This was traced to a sign/unsigned mix up in the OPAL sysparam
sysfs code at sys_param_show.
The return value of sys_param_show is a ssize_t, calculated using
return ret ? ret : attr->param_size;
Alan Modra explains:
"attr->param_size" is an unsigned int, "ret" an int, so the overall
expression has type unsigned int. Result is that ret is cast to
unsigned int before being cast to ssize_t.
Instead of using the ternary operator, set ret to the param_size if an
error is not detected. The same bug exists in the sysfs write callback;
this patch fixes it in the same way.
A note on debugging this next time: on my system gcc will warn about
this if compiled with -Wsign-compare, which is not enabled by -Wall,
only -Wextra.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
- Fix for a recently introduced CPU hotplug regression in ARM KVM
from Ming Lei.
- Fixes for breakage in the at32ap, loongson2_cpufreq, and unicore32
cpufreq drivers introduced during the 3.14 cycle (-stable material)
from Chen Gang and Viresh Kumar.
- New powernv cpufreq driver from Vaidyanathan Srinivasan, with bits
from Gautham R Shenoy and Srivatsa S Bhat.
- Exynos cpufreq driver fix preventing it from being included into
multiplatform builds that aren't supported by it from Sachin Kamat.
- cpufreq cleanups related to the usage of the driver_data field in
struct cpufreq_frequency_table from Viresh Kumar.
- cpufreq ppc driver cleanup from Sachin Kamat.
- Intel BayTrail support for intel_idle and ACPI idle from Len Brown.
- Intel CPU model 54 (Atom N2000 series) support for intel_idle from
Jan Kiszka.
- intel_idle fix for Intel Ivy Town residency targets from Len Brown.
- turbostat updates (Intel Broadwell support and output cleanups)
from Len Brown.
- New cpuidle sysfs attribute for exporting C-states' target residency
information to user space from Daniel Lezcano.
- New kernel command line argument to prevent power domains enabled
by the bootloader from being turned off even if they are not in use
(for diagnostics purposes) from Tushar Behera.
- Fixes for wakeup sysfs attributes documentation from Geert Uytterhoeven.
- New ACPI video blacklist entry for ThinkPad Helix from Stephen Chandler
Paul.
- Assorted ACPI cleanups and a Kconfig help update from Jonghwan Choi,
Zhihui Zhang, Hanjun Guo.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=hGKg
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.15-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management fixes and updates from Rafael Wysocki:
"This is PM and ACPI material that has emerged over the last two weeks
and one fix for a CPU hotplug regression introduced by the recent CPU
hotplug notifiers registration series.
Included are intel_idle and turbostat updates from Len Brown (these
have been in linux-next for quite some time), a new cpufreq driver for
powernv (that might spend some more time in linux-next, but BenH was
asking me so nicely to push it for 3.15 that I couldn't resist), some
cpufreq fixes and cleanups (including fixes for some silly breakage in
a couple of cpufreq drivers introduced during the 3.14 cycle),
assorted ACPI cleanups, wakeup framework documentation fixes, a new
sysfs attribute for cpuidle and a new command line argument for power
domains diagnostics.
Specifics:
- Fix for a recently introduced CPU hotplug regression in ARM KVM
from Ming Lei.
- Fixes for breakage in the at32ap, loongson2_cpufreq, and unicore32
cpufreq drivers introduced during the 3.14 cycle (-stable material)
from Chen Gang and Viresh Kumar.
- New powernv cpufreq driver from Vaidyanathan Srinivasan, with bits
from Gautham R Shenoy and Srivatsa S Bhat.
- Exynos cpufreq driver fix preventing it from being included into
multiplatform builds that aren't supported by it from Sachin Kamat.
- cpufreq cleanups related to the usage of the driver_data field in
struct cpufreq_frequency_table from Viresh Kumar.
- cpufreq ppc driver cleanup from Sachin Kamat.
- Intel BayTrail support for intel_idle and ACPI idle from Len Brown.
- Intel CPU model 54 (Atom N2000 series) support for intel_idle from
Jan Kiszka.
- intel_idle fix for Intel Ivy Town residency targets from Len Brown.
- turbostat updates (Intel Broadwell support and output cleanups)
from Len Brown.
- New cpuidle sysfs attribute for exporting C-states' target
residency information to user space from Daniel Lezcano.
- New kernel command line argument to prevent power domains enabled
by the bootloader from being turned off even if they are not in use
(for diagnostics purposes) from Tushar Behera.
- Fixes for wakeup sysfs attributes documentation from Geert
Uytterhoeven.
- New ACPI video blacklist entry for ThinkPad Helix from Stephen
Chandler Paul.
- Assorted ACPI cleanups and a Kconfig help update from Jonghwan
Choi, Zhihui Zhang, Hanjun Guo"
* tag 'pm+acpi-3.15-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
ACPI: Update the ACPI spec information in Kconfig
arm, kvm: fix double lock on cpu_add_remove_lock
cpuidle: sysfs: Export target residency information
cpufreq: ppc: Remove duplicate inclusion of fsl_soc.h
cpufreq: create another field .flags in cpufreq_frequency_table
cpufreq: use kzalloc() to allocate memory for cpufreq_frequency_table
cpufreq: don't print value of .driver_data from core
cpufreq: ia64: don't set .driver_data to index
cpufreq: powernv: Select CPUFreq related Kconfig options for powernv
cpufreq: powernv: Use cpufreq_frequency_table.driver_data to store pstate ids
cpufreq: powernv: cpufreq driver for powernv platform
cpufreq: at32ap: don't declare local variable as static
cpufreq: loongson2_cpufreq: don't declare local variable as static
cpufreq: unicore32: fix typo issue for 'clk'
cpufreq: exynos: Disable on multiplatform build
PM / wakeup: Correct presence vs. emptiness of wakeup_* attributes
PM / domains: Add pd_ignore_unused to keep power domains enabled
ACPI / dock: Drop dock_device_ids[] table
ACPI / video: Favor native backlight interface for ThinkPad Helix
ACPI / thermal: Fix wrong variable usage in debug statement
...
We are currently using sysfs_schedule_callback() which is deprecated
and about to be removed. Switch to the new interface instead.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This call will not be understood by OPAL, and cause it to add an error
to it's log. Among other things, this is useful for testing the
behaviour of the log as it fills up.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
OPAL provides an in-memory circular buffer containing a message log
populated with various runtime messages produced by the firmware.
Provide a sysfs interface /sys/firmware/opal/msglog for userspace to
view the messages.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we wrongly allocate mc_recoverable_range buffer (to hold
recoverable ranges) based on size of the property "mcheck-recoverable-ranges".
This results in allocating less memory to hold available recoverable range
entries from /proc/device-tree/ibm,opal/mcheck-recoverable-ranges.
This patch fixes this issue by allocating mc_recoverable_range buffer based
on number of entries of recoverable ranges instead of device property size.
Without this change we end up allocating less memory and run into memory
corruption issue.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
One OPAL call and one device tree property needed byte swapping.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable CPUFreq for PowerNV. Select "performance", "powersave",
"userspace" and "ondemand" governors. Choose "ondemand" to be the
default governor.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
OPAL defines opal_msg as a big endian struct so we have to
byte swap it on little endian builds.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
opal_notifier_register() is missing a pending "unregister" variant
and should be exposed to modules.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull powerpc non-virtualized cpuidle from Ben Herrenschmidt:
"This is the branch I mentioned in my other pull request which contains
our improved cpuidle support for the "powernv" platform
(non-virtualized).
It adds support for the "fast sleep" feature of the processor which
provides higher power savings than our usual "nap" mode but at the
cost of losing the timers while asleep, and thus exploits the new
timer broadcast framework to work around that limitation.
It's based on a tip timer tree that you seem to have already merged"
* 'powernv-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
cpuidle/powernv: Parse device tree to setup idle states
cpuidle/powernv: Add "Fast-Sleep" CPU idle state
powerpc/powernv: Add OPAL call to resync timebase on wakeup
powerpc/powernv: Add context management for Fast Sleep
powerpc: Split timer_interrupt() into timer handling and interrupt handling routines
powerpc: Implement tick broadcast IPI as a fixed IPI message
powerpc: Free up the slot of PPC_MSG_CALL_FUNC_SINGLE IPI message
Pull main powerpc updates from Ben Herrenschmidt:
"This time around, the powerpc merges are going to be a little bit more
complicated than usual.
This is the main pull request with most of the work for this merge
window. I will describe it a bit more further down.
There is some additional cpuidle driver work, however I haven't
included it in this tree as it depends on some work in tip/timer-core
which Thomas accidentally forgot to put in a topic branch. Since I
didn't want to carry all of that tip timer stuff in powerpc -next, I
setup a separate branch on top of Thomas tree with just that cpuidle
driver in it, and Stephen has been carrying that in next separately
for a while now. I'll send a separate pull request for it.
Additionally, two new pieces in this tree add users for a sysfs API
that Tejun and Greg have been deprecating in drivers-core-next.
Thankfully Greg reverted the patch that removes the old API so this
merge can happen cleanly, but once merged, I will send a patch
adjusting our new code to the new API so that Greg can send you the
removal patch.
Now as for the content of this branch, we have a lot of perf work for
power8 new counters including support for our new "nest" counters
(also called 24x7) under pHyp (not natively yet).
We have new functionality when running under the OPAL firmware
(non-virtualized or KVM host), such as access to the firmware error
logs and service processor dumps, system parameters and sensors, along
with a hwmon driver for the latter.
There's also a bunch of bug fixes accross the board, some LE fixes,
and a nice set of selftests for validating our various types of copy
loops.
On the Freescale side, we see mostly new chip/board revisions, some
clock updates, better support for machine checks and debug exceptions,
etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (70 commits)
powerpc/book3s: Fix CFAR clobbering issue in machine check handler.
powerpc/compat: 32-bit little endian machine name is ppcle, not ppc
powerpc/le: Big endian arguments for ppc_rtas()
powerpc: Use default set of netfilter modules (CONFIG_NETFILTER_ADVANCED=n)
powerpc/defconfigs: Enable THP in pseries defconfig
powerpc/mm: Make sure a local_irq_disable prevent a parallel THP split
powerpc: Rate-limit users spamming kernel log buffer
powerpc/perf: Fix handling of L3 events with bank == 1
powerpc/perf/hv_{gpci, 24x7}: Add documentation of device attributes
powerpc/perf: Add kconfig option for hypervisor provided counters
powerpc/perf: Add support for the hv 24x7 interface
powerpc/perf: Add support for the hv gpci (get performance counter info) interface
powerpc/perf: Add macros for defining event fields & formats
powerpc/perf: Add a shared interface to get gpci version and capabilities
powerpc/perf: Add 24x7 interface headers
powerpc/perf: Add hv_gpci interface header
powerpc: Add hvcalls for 24x7 and gpci (Get Performance Counter Info)
sysfs: create bin_attributes under the requested group
powerpc/perf: Enable BHRB access for EBB events
powerpc/perf: Add BHRB constraint and IFM MMCRA handling for EBB
...
This patch enables fetching of various platform sensor data through
OPAL and expects a sensor handle from the driver to pass to OPAL.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch enables reading and updating of system parameters through
OPAL call.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support for notifying the clients of their request
completion. Clients request for the token before making OPAL call
and then wait for the response.
This patch uses messaging infrastructure to pull the data to linux
by registering itself for the message type OPAL_MSG_ASYNC_COMP.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This enables support for userspace to fetch and initiate FSP and
Platform dumps from the service processor (via firmware) through sysfs.
Based on original patch from Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Flow:
- We register for OPAL notification events.
- OPAL sends new dump available notification.
- We make information on dump available via sysfs
- Userspace requests dump contents
- We retrieve the dump via OPAL interface
- User copies the dump data
- userspace sends ack for dump
- We send ACK to OPAL.
sysfs files:
- We add the /sys/firmware/opal/dump directory
- echoing 1 (well, anything, but in future we may support
different dump types) to /sys/firmware/opal/dump/initiate_dump
will initiate a dump.
- Each dump that we've been notified of gets a directory
in /sys/firmware/opal/dump/ with a name of the dump type and ID (in hex,
as this is what's used elsewhere to identify the dump).
- Each dump has files: id, type, dump and acknowledge
dump is binary and is the dump itself.
echoing 'ack' to acknowledge (currently any string will do) will
acknowledge the dump and it will soon after disappear from sysfs.
OPAL APIs:
- opal_dump_init()
- opal_dump_info()
- opal_dump_read()
- opal_dump_ack()
- opal_dump_resend_notification()
Currently we are only ever notified for one dump at a time (until
the user explicitly acks the current dump, then we get a notification
of the next dump), but this kernel code should "just work" when OPAL
starts notifying us of all the dumps present.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Based on a patch by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
This patch adds support to read error logs from OPAL and export
them to userspace through a sysfs interface.
We export each log entry as a directory in /sys/firmware/opal/elog/
Currently, OPAL will buffer up to 128 error log records, we don't
need to have any knowledge of this limit on the Linux side as that
is actually largely transparent to us.
Each error log entry has the following files: id, type, acknowledge, raw.
Currently we just export the raw binary error log in the 'raw' attribute.
In a future patch, we may parse more of the error log to make it a bit
easier for userspace (e.g. to be able to display a brief summary in
petitboot without having to have a full parser).
If we have >128 logs from OPAL, we'll only be notified of 128 until
userspace starts acknowledging them. This limitation may be lifted in
the future and with this patch, that should "just work" from the linux side.
A userspace daemon should:
- wait for error log entries using normal mechanisms (we announce creation)
- read error log entry
- save error log entry safely to disk
- acknowledge the error log entry
- rinse, repeat.
On the Linux side, we read the error log when we're notified of it. This
possibly isn't ideal as it would be better to only read them on-demand.
However, this doesn't really work with current OPAL interface, so we
read the error log immediately when notified at the moment.
I've tested this pretty extensively and am rather confident that the
linux side of things works rather well. There is currently an issue with
the service processor side of things for >128 error logs though.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Detect and recover from machine check when inside opal on a special
scom load instructions. On specific SCOM read via MMIO we may get a machine
check exception with SRR0 pointing inside opal. To recover from MC
in this scenario, get a recovery instruction address and return to it from
MC.
OPAL will export the machine check recoverable ranges through
device tree node mcheck-recoverable-ranges under ibm,opal:
# hexdump /proc/device-tree/ibm,opal/mcheck-recoverable-ranges
0000000 0000 0000 3000 2804 0000 000c 0000 0000
0000010 3000 2814 0000 0000 3000 27f0 0000 000c
0000020 0000 0000 3000 2814 xxxx xxxx xxxx xxxx
0000030 llll llll yyyy yyyy yyyy yyyy
...
...
#
where:
xxxx xxxx xxxx xxxx = Starting instruction address
llll llll = Length of the address range.
yyyy yyyy yyyy yyyy = recovery address
Each recoverable address range entry is (start address, len,
recovery address), 2 cells each for start and recovery address, 1 cell for
len, totalling 5 cells per entry. During kernel boot time, build up the
recovery table with the list of recovery ranges from device-tree node which
will be used during machine check exception to recover from MMIO SCOM UE.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During "Fast-sleep" and deeper power savings state, decrementer and
timebase could be stopped making it out of sync with rest
of the cores in the system.
Add a firmware call to request platform to resync timebase
using low level platform methods.
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to unmangle the full address, not just the register
number, and we also need to support the real indirect bit
being set for in-kernel uses.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.13]
As Ben suggested, the patch prints PHB diag-data with multiple
fields in one line and omits the line if the fields of that
line are all zero.
With the patch applied, the PHB3 diag-data dump looks like:
PHB3 PHB#3 Diag-data (Version: 1)
brdgCtl: 00000002
RootSts: 0000000f 00400000 b0830008 00100147 00002000
nFir: 0000000000000000 0030006e00000000 0000000000000000
PhbSts: 0000001c00000000 0000000000000000
Lem: 0000000000100000 42498e327f502eae 0000000000000000
InAErr: 8000000000000000 8000000000000000 0402030000000000 0000000000000000
PE[ 8] A/B: 8480002b00000000 8000000000000000
[ The current diag data is so big that it overflows the printk
buffer pretty quickly in cases when we get a handful of errors
at once which can happen. --BenH
]
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PHB diag-data is important to help locating the root cause for
EEH errors such as frozen PE or fenced PHB. However, the EEH core
enables IO path by clearing part of HW registers before collecting
this data causing it to be corrupted.
This patch fixes this by dumping the PHB diag-data immediately when
frozen/fenced state on PE or PHB is detected for the first time in
eeh_ops::get_state() or next_error() backend.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The core idle loop now takes care of it. We need to add the runlatch
function calls to the idle routines which was earlier taken care of by
the arch specific idle routine.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Reviewed-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-pm@vger.kernel.org
Cc: linaro-kernel@lists.linaro.org
Link: http://lkml.kernel.org/n/tip-nr4mtbkkzf2oomaj85m24o7c@git.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We possiblly detect EEH errors during reboot, particularly in kexec
path, but it's impossible for device drivers and EEH core to handle
or recover them properly.
The patch registers one reboot notifier for EEH and disable EEH
subsystem during reboot. That means the EEH errors is going to be
cleared by hardware reset or second kernel during early stage of
PCI probe.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch cleans up variable eeh_subsystem_enabled so that we needn't
refer the variable directly from external. Instead, we will use
function eeh_enabled() and eeh_set_enable() to operate the variable.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When doing reset in order to recover the affected PE, we issue
hot reset on PE primary bus if it's not root bus. Otherwise, we
issue hot or fundamental reset on root port or PHB accordingly.
For the later case, we didn't cover the situation where PE only
includes root port and it potentially causes kernel crash upon
EEH error to the PE.
The patch reworks the logic of EEH reset to improve the code
readability and also avoid the kernel crash.
Cc: stable@vger.kernel.org
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds the support for to create a direct iommu "bypass"
window on IODA2 bridges (such as Power8) allowing to bypass iommu
page translation completely for 64-bit DMA capable devices, thus
significantly improving DMA performances.
Additionally, this adds a hook to the struct iommu_table so that
the IOMMU API / VFIO can disable the bypass when external ownership
is requested, since in that case, the device will be used by an
environment such as userspace or a KVM guest which must not be
allowed to bypass translations.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Following patch ports the cpuidle framework for powernv
platform and also implements a cpuidle back-end powernv
idle driver calling on to power7_nap and snooze idle states.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull powerpc updates from Ben Herrenschmidt:
"So here's my next branch for powerpc. A bit late as I was on vacation
last week. It's mostly the same stuff that was in next already, I
just added two patches today which are the wiring up of lockref for
powerpc, which for some reason fell through the cracks last time and
is trivial.
The highlights are, in addition to a bunch of bug fixes:
- Reworked Machine Check handling on kernels running without a
hypervisor (or acting as a hypervisor). Provides hooks to handle
some errors in real mode such as TLB errors, handle SLB errors,
etc...
- Support for retrieving memory error information from the service
processor on IBM servers running without a hypervisor and routing
them to the memory poison infrastructure.
- _PAGE_NUMA support on server processors
- 32-bit BookE relocatable kernel support
- FSL e6500 hardware tablewalk support
- A bunch of new/revived board support
- FSL e6500 deeper idle states and altivec powerdown support
You'll notice a generic mm change here, it has been acked by the
relevant authorities and is a pre-req for our _PAGE_NUMA support"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (121 commits)
powerpc: Implement arch_spin_is_locked() using arch_spin_value_unlocked()
powerpc: Add support for the optimised lockref implementation
powerpc/powernv: Call OPAL sync before kexec'ing
powerpc/eeh: Escalate error on non-existing PE
powerpc/eeh: Handle multiple EEH errors
powerpc: Fix transactional FP/VMX/VSX unavailable handlers
powerpc: Don't corrupt transactional state when using FP/VMX in kernel
powerpc: Reclaim two unused thread_info flag bits
powerpc: Fix races with irq_work
Move precessing of MCE queued event out from syscall exit path.
pseries/cpuidle: Remove redundant call to ppc64_runlatch_off() in cpu idle routines
powerpc: Make add_system_ram_resources() __init
powerpc: add SATA_MV to ppc64_defconfig
powerpc/powernv: Increase candidate fw image size
powerpc: Add debug checks to catch invalid cpu-to-node mappings
powerpc: Fix the setup of CPU-to-Node mappings during CPU online
powerpc/iommu: Don't detach device without IOMMU group
powerpc/eeh: Hotplug improvement
powerpc/eeh: Call opal_pci_reinit() on powernv for restoring config space
powerpc/eeh: Add restore_config operation
...
Gavin Shan