For the quite common 'skb->h.raw - skb->data' sequence.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->h.raw = skb->data' operation, so that we can
later turn skb->h.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple cases:
skb->h.raw = skb->data;
skb->h.raw = {skb_push|[__]skb_pull}()
The next ones will handle the slightly more "complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the skb->nh union has just one member, .raw, i.e. it is just like the
skb->mac union, strange, no? I'm just leaving it like that till the transport
layer is done with, when we'll rename skb->mac.raw to skb->mac_header (or
->mac_header_offset?), ditto for ->{h,nh}.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common sequence "skb->nh.iph->ihl * 4", removing a good number of open
coded skb->nh.iph uses, now to go after the rest...
Just out of curiosity, here are the idioms found to get the same result:
skb->nh.iph->ihl << 2
skb->nh.iph->ihl<<2
skb->nh.iph->ihl * 4
skb->nh.iph->ihl*4
(skb->nh.iph)->ihl * sizeof(u32)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the places where we need a pointer to the network header, it is still legal
to touch skb->nh.raw directly if just adding to, subtracting from or setting it
to another layer header.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the quite common 'skb->nh.raw - skb->data' sequence.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->nh.raw = skb->data' operation, so that we can
later turn skb->nh.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency with all the other skb->nh.raw accessors.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency with all the other skb->nh.raw accessors.
Also do some really obvious simplifications in pppoe_recvmsg, well the
kfree_skb one is not so obvious, but free() and kfree() have the same behaviour
(hint :-) ).
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the places where we need a pointer to the mac header, it is still legal to
touch skb->mac.raw directly if just adding to, subtracting from or setting it
to another layer header.
This one also converts some more cases to skb_reset_mac_header() that my
regex missed as it had no spaces before nor after '=', ugh.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the cases where we want to set skb->mac.raw to an offset from skb->data.
Simple cases first, the memmove ones and specially pktgen will be left for later.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->mac.raw = skb->data' operation, so that we can
later turn skb->mac.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One less thing for drivers writers to worry about.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now all the _type_trans routines are consistent in this regard.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tweak a register setting to prevent the tx mailbox from halting.
Update version to 1.5.8.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sparc64:
drivers/net/hamradio/baycom_ser_fdx.c: In function `ser12_open':
drivers/net/hamradio/baycom_ser_fdx.c:417: error: `NR_IRQS' undeclared (first us
e in this function)
drivers/net/hamradio/baycom_ser_fdx.c:417: error: (Each undeclared identifier is
reported only once
drivers/net/hamradio/baycom_ser_fdx.c:417: error: for each function it appears i
n.)
Cc: Folkert van Heusden <folkert@vanheusden.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sis900 driver appears to have a bug in which the receive routine
passes the skbuff holding the received frame to the network stack before
refilling the buffer in the rx ring. If a new skbuff cannot be allocated, the
driver simply leaves a hole in the rx ring, which causes the driver to stop
receiving frames and become non-recoverable without an rmmod/insmod according to
reporters. This patch reverses that order, attempting to allocate a replacement
buffer first, and receiving the new frame only if one can be allocated. If no
skbuff can be allocated, the current skbuf in the rx ring is recycled, dropping
the current frame, but keeping the NIC operational.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The following patch fixes a kernel bug in depca_platform_probe().
We don't use a dynamic pointer for pldev->dev.platform_data, so it seems
that the correct way to proceed if platform_device_add(pldev) fails is
to explicitly set the pldev->dev.platform_data pointer to NULL, before
calling the platform_device_put(pldev), or it will be kfree'ed by
platform_device_release().
Signed-off-by: Jeff Garzik <jeff@garzik.org>
USRobotics Wireless Adapter (Model 5423) works well with current
zd1211rw driver also (i have tested 2.6.18, 2.6.20 and 2.6.21-rc7).
It just needs its ID added to the list of devices.
Signed-off-by: S.Çağlar Onur <caglar@pardus.org.tr>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MAC address assignment at module loading is simply forgotten.
The bug at module unloading is caused by an incorrect call.
The bug at module unloading does not only happen for sunqe,
sunlance and sunhme (sbus) suffer from it too.
I've tested this on my SS20.
Signed-off-by: Marcel van Nies <morcles@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the unnecessary bit number from CKENnn_XXXX
definitions for PXA, so that
CKEN0_PWM0 --> CKEN_PWM0
CKEN1_PWM1 --> CKEN_PWM1
...
CKEN24_CAMERA --> CKEN_CAMERA
The reasons for the change of these defitions are:
1. they do not scale - they are currently valid for pxa2xx, but
definitely not valid for pxa3xx, e.g., pxa3xx has bit 3 for camera
instead of bit 24
2. they are unnecessary - the peripheral name within the definition
has already announced its usage, we don't need those bit numbers
to know which peripheral we are going to enable/disable clock for
3. they are inconvenient - think about this: a driver programmer
for pxa has to remember which bit in the CKEN register to turn
on/off
Another change in the patch is to make the definitions equal to its
clock bit index, so that
#define CKEN_CAMERA (24)
instead of
#define CKEN_CAMERA (1 << 24)
this change, however, will add a run-time bit shift operation in
pxa_set_cken(), but the benefit of this change is that it scales
when bit index exceeds 32, e.g., pxa3xx has two registers CKENA
and CKENB, totally 64 bit for this, suppose CAMERA clock enabling
bit is CKENB:10, one can simply define CKEN_CAMERA to be (32 + 10)
and so that pxa_set_cken() need minimum change to adapt to that.
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 60cba200f1. It's been
linked to lockups of the e1000 hardware, see for example
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=229603
but it's likely that the commit itself is not really introducing the
bug, but just allowing an unrelated problem to rear its ugly head (ie
one current working theory is that the code exposes us to a hardware
race condition by decreasing the amount of time we spend in each NAPI
poll cycle).
We'll revert it until root cause is known. Intel has a repeatable
reproduction on two different machines and bus traces of the hardware
doing something bad.
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Greg KH <gregkh@suse.de>
Cc: Dave Jones <davej@redhat.com>
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From: Paul Mackerras <paulus@samba.org>
This fixes:
Subject: kernel BUG at net/core/skbuff.c in linux-2.6.21-rc6
process_input_packet() treats the case where the first byte is 0xff
(PPP_ALLSTATIONS) but the second byte is 0x03 (PPP_UI) as indicating a
packet with a PPP protocol number of 0xff. Arguably that's wrong
since PPP protocol 0xff is reserved, and the RFC does envision the
possibility of receiving frames where the control field has values
other than 0x03.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Yukon FE (100mbit only) chips do not support large packets.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Yukon EC Ultra chips have transmit settings for store and
forward and PCI buffering. By setting these appropriately, normal
performance goes from 750Mbytes/sec to 940Mbytes/sec (non-jumbo).
It is also possible to do Jumbo mode, but it means turning off
TSO and checksum offload so the performance gets worse. There isn't
enough buffering for checksum offload to work.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Need to make sure and disable ASF on all chip types. Otherwise, there may be
random reboots.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There should never be descriptor error unless hardware or driver is buggy.
But if an error occurs, print useful information, clear irq, and recover.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This device is having all sorts of problems that lead to data corruption
and system instability. It gets receive status and data out of order,
it generates descriptor and TSO errors, etc.
Until the problems are resolved, it should not be used by anyone
who cares about there system.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The basic structure of "normal" UDP/IP/Ethernet
frames (that actually work):
- It starts with the Ethernet header (dest MAC, src MAC, etc.)
- The next part is occupied by the IP header (version info, length of
packet, id=0, fragment offset=0, checksum, from / to address, etc.)
- Then comes the UDP header (src / dest port, length, checksum)
- Actual payload
- Ethernet checksum
Now what's different for IP fragment:
- The IP header has id set to some value (same for all fragments),
offset is set appropriately (i.e. 0 for first fragment, following
according to size of other fragments), size is the length of the frame.
- UDP header is unchanged. I.e. length is according to full UDP
datagram, not just the part within the actual frame! But this is only
true within the first frame: all following frames don't have a valid
UDP-header at all.
The spidernet silicon seems to be quite intelligent: It's able to
compute (IP / UDP / Ethernet) checksums on the fly and tests if frames
are conforming to RFC -- at least conforming to RFC on complete frames.
But IP fragments are different as explained above:
I.e. for IP fragments containing part of a UDP datagram it sees
incompatible length in the headers for IP and UDP in the first frame
and, thus, skips this frame. But the content *is* correct for IP
fragments. For all following frames it finds (most probably) no valid
UDP header at all. But this *is* also correct for IP fragments.
The Linux IP-stack seems to be clever in this point. It expects the
spidernet to calculate the checksum (since the module claims to be able
to do so) and marks the skb's for "normal" frames accordingly
(ip_summed set to CHECKSUM_HW).
But for the IP fragments it does not expect the driver to be capable to
handle the frames appropriately. Thus all checksums are allready
computed. This is also flaged within the skb (ip_summed set to
CHECKSUM_NONE).
Unfortunately the spidernet driver ignores that hints. It tries to send
the IP fragments of UDP datagrams as normal UDP/IP frames. Since they
have different structure the silicon detects them the be not
"well-formed" and skips them.
The following one-liner against 2.6.21-rc2 changes this behavior. If the
IP-stack claims to have done the checksumming, the driver should not
try to checksum (and analyze) the frame but send it as is.
Signed-off-by: Norbert Eicker <n.eicker@fz-juelich.de>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove assumption that PHY interrupts use GPIOs 3 and 5.
Deal with PHY interrupts connected to any GPIO pins.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reuse the incoming skb when a clientless abort req is recieved.
The release of RDMA connections HW resources might be deferred in
low memory situations.
Ensure that no further activity is passed up to the RDMA driver
for these connections.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the Intel 5000 southbridge (aka Intel 6310/6311/6321ESB) PCIe ports
and the Intel E30x0 chipsets to the whitelist of aligned PCIe completion.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simpler way of dealing with the firmware 4KB boundary crossing
restriction for rx buffers. This fixes a variety of memory
corruption issues when using an "uncommon" MTU with a 16KB
page size.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove specific CPL handler.
Add missing CPL handler.
Add missing register setting when the interface is brought up.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The MAC watchdog was failing if the peer interface was brought down.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a deadlock when the interface s configured down and
the watchdog tack is sleeping on rtnl_lock.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Need to rework wake on lan code to setup properly and get activated
on shutdown (and suspend), not when ethtool is run.
This does not need to go to stable queue because wake on lan
was not even included in 2.6.20 (or earlier versions).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The workaround Yukon EC-U wasn't comparing with correct
version and wasn't doing correct setup. Without it, 88e8056
throws all sorts of errors.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some of these chips are disabled until clock is enabled.
This fixes:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=404107
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver needs to turn off carrier when down.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver needs to turn off carrier when down, otherwise it can
confuse bonding and bridging and looks like carrier is on immediately
when it is brought back up.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The specifications for loopback_gain calculation and for G PHY
initialization have been updated. This patch implements them and
fixes a machine check error that occurs for PPC architecture with a
phy->rev of 1.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In 802.11b/g mode, bcm43xx actively scans channels 1-14 no matter what
locale has been set, either in the sprom or by the locale option. This
behaviorviolates regulatory rules everywhere in the world except
Japan. This patch changes the default range to the correct value if the
locale has been set, and to channels 1-13 if no locale has been set.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to conflicting/confusing defines in the vendor driver, we were
reading E2P_PHY_REG from the wrong location.
CR157 patching was slightly incorrect in that the vendor driver only
patches in an 8-bit value, whereas we were patching 24 bits.
Additionally, CR157 patching was happening on both zd1211 and zd1211b,
but this should only happen on zd1211.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1211rw currently detects AL2230S-based devices as AL2230, and hence
programs the RF incorrectly. Transmit silently fails on this
misconfiguration.
After this patch, AL2230S devices are rejected with an error message, to
avoid any confusion with an apparent driver bug.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The spin_lock calls made in dev->open and dev->close must disable
BH since open/close are made in process context. Conversely, the
call in dev->hard_start_xmit does not need to disable BH since it
is already executing with BH disabled.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver will crash when the chip has been initialized by EFI before
tg3_init_one(). In this case, the driver will call tg3_chip_reset()
before allocating consistent memory.
The bug is fixed by checking for tp->hw_status before accessing it
during tg3_chip_reset().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PM hooks are no-op if the r8169 interface is down (i.e. !IFF_UP).
However, as the chipset is enabled, the device will not work after a
suspend/resume cycle. The patch always issue the required PCI suspend
sequence and removes the module unload/reload workaround.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The irq handler schedules a NAPI poll request unconditionally as soon as
the status register is not clean. It has been there - and wrong - for
ages but a recent timing change made it apparently easier to trigger.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If you set the IFF_ALLMULTI flag on a b44 device, or if you join more than
B44_MCAST_TABLE_SIZE multicast groups, the device will stop receiving unicast
messages. This is because the __b44_set_mac_addr call sets the zeroth CAM
entry to the MAC address of the device, and then the loop at line 1722
proceeds to overwrite it unless the value of i is set by the __b44_load_mcast
call. However, when IFF_ALLMULTI is set, that call is bypassed, leaving i set
to zero.
Fixed by starting the loop at 1 to make it skip the CAM entry for the MAC
address.
Signed-off-by: Bill Helfinstine <bhelf@flitterfly.whirpon.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Run the watchdog task when the link is up.
Flush the XGMAC Tx FIFO when the link drops.
Also remove a statistics update that should have gone
in the previous modification of xgmac.c.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Differentiate NIC only adapters from RNICs.
Initialize offload capabilities for RNICs only.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The nvram dword alignment logic was broken when writing less than 4
bytes on a non-aligned offset. It was missing logic to round the
length to 4 bytes.
The page erase code is also moved so that it is only called when
using non-buffered flash for better code clarity.
Update version to 1.5.7.
Based on initial patch from Tony Cureington <tony.cureington@hp.com>.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses the following issues with the pxa2xx FIr driver:
1. increment overrun error counter and not frame error counter on ICSR1_ROR bit set in ICSR1.
2. drop frames reported with the frame error from the IC.
3. when resetting the receiver and preparing it for the next DMA in pxa_irda_fir_irq() actually clear the Rx FIFO. See description in Table 11-2 in PXA270 Developer's Manual of the RXE bit.
Correction added in version 2: clearing the IC Rx FIFO also has to be done in pxa_irda_fir_dma_tx_irq()
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
NetXen: Fix hardware access for ppc architecture.
sis190: new PHY support
atl1: save mac address on remove
The input_device pointer is not refcounted, which means the device may
disappear while packets are queued, causing a crash when ifb passes packets
with a stale skb->dev pointer to netif_rx().
Fix by storing the interface index instead and do a lookup where neccessary.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported to work on the WinFast 761GXK8MB-RS motherboard.
Plain 10/100 Mbps.
Signed-off-by: Paul Gibbons <paul@pkami.e7even.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some atl1 boards get their MAC address written directly to the register
by the BIOS during POST, rather than storing it in EEPROM that's
accessible to the driver. If the MAC register on one of these boards
is changed and then the module is unloaded, the permanent MAC address
will be forgotten until the box is rebooted. We should save the
permanent address during removal if we've been messing with it.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
bnx2_has_work()'s logic is flawed and can cause the driver to miss
a link event. The fix is to compare the status block's attn_bits
and attn_bits_ack to determine if there is a link event.
Update version to 1.5.6.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds checking for allocated DVMA memory and granted IRQ line.
Signed-off-by: Cyrill V. Gorcunov <gorcunov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In this driver, the default ethernet address is first set by by calling
eth_port_uc_addr_get() which reads the relevant registers of the
corresponding port as initially set by firmware. However that function
used the port_num field accessed through the private area of net_dev
before it was set.
The result was that one board I have ended up with the unicast address
set to 00:00:00:00:00:00 (only port 1 is connected on this board). The
problem appeared after commit 84dd619e4d.
This patch fixes the bug by setting mp->port_num prior to calling
eth_port_uc_get_addr().
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The tx timeout routine was waking the tx queue conditionally. However,
it must call it unconditionally since the dev_watchdog has halted the tx
queue before calling the timeout function.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The nic poll routine was missing the call to the optimized irq routine.
This patch adds the missing call for the optimized path.
See http://bugzilla.kernel.org/show_bug.cgi?id=7950 for more information.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixed rx checksum bits. Turn on TCP processing for rx checksum.
Fixed max frame length register write. It wasn't getting set
in multi-port system. Set rx buffer queue length properly
for jumbo frames.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the rx queue pointer when exiting NAPI poll rather than
at the end of each iteration. Remove unnecessary PCI flushes
that occurred after every write. Now write all regs and
flush once.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This was removed in a previous patch to increase performance, but
caused a transmit error for the 4032 chip.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The original vendor driver contained a private ether_crc_le() function
that produced an inverted crc. When we changed to the kernel version of
ether_crc_le(), we neglected to undo the inversion. Let's do it now.
Discovered by and patch proffered by Jose Alberto Reguero.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Correctly detect when TSO should be used on transmit by looking at the
skb->gso_size rather than seeing if the frame was larger than our MTU.
The old method causes problems when a host with a large (jumbo) MTU is
sending to a host with a small (standard) MTU.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recent changes in the specs that were introduced in commit
740ac4fb08 were incorrect and resulted in machine check
errors on the PPC architecture for G PHY's with a revision number equal to 1. The
two offending changes are reverted.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a duplicated leftshift in bcm43xx_radio_set_tx_iq. data_high values are
already leftshifted. Thanks to Michael Buesch for spotting this.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are several places where the PHY version and revision were interchanged.
These are changed in the specifications on 2/13/07 and now use "analog" instead
instead of "version" to help reduce confusion.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change the Kconfig files so that the Freescale QE options are automatically
selected if a QE device is selected. Previously, you'd need to manually
select UCC_FAST if you want any "fast" UCC devices, such as Gigabit Ethernet.
Now, the QE Gigabit Ethernet option is always available if the device has a
QE, and UCC_FAST is automatically enabled. A side-effect is that the
"QE Options" menu no longer exists.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch implements set_mac_address for the sungem driver. This
allows changing the mac address of the interface, even when the
interface is up.
Signed-off-by: Ruben Vandeginste <snowbender@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On most tg3 chips, the memory enable bit in the PCI command register
gets cleared during chip reset and must be restored before accessing
PCI registers using memory cycles. The chip does not generate
interrupt during chip reset, but the irq handler can still be called
because of irq sharing or irqpoll. Reading a register in the irq
handler can cause a master abort in this scenario and may result in a
crash on some architectures.
Use the TG3_FLAG_CHIP_RESETTING flag to tell the irq handler to exit
without touching any registers. The checking of the flag is in the
"slow" path of the irq handler and will not affect normal performance.
The msi handler is not shared and therefore does not require checking
the flag.
Thanks to Bernhard Walle <bwalle@suse.de> for reporting the problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This flag to support multiple PCIX split completions was never used
because of hardware bugs. This will make room for a new flag.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arwin Vosselman pointed out:
> The ewrk3-driver doesn't function with 2.6.16-kernels (used 2.6.16.41 for
> my tests). Cards will never be detected due to this bug.
>
> drivers/net/ewrks3.c:
> Line 417 reads:
>
> if (nicsr == (CSR_TXD | CSR_RXD))
>
> that should be:
>
> if (nicsr != (CSR_TXD | CSR_RXD))
>
> Comparison with the same line in v2.4 shows why:
>
> 2.4:
> if (nicsr == (CSR_TXD | CSR_RXD)){
>
> blah, blah
> ==========
> 2.6:
> if (nicsr == (CSR_TXD | CSR_RXD))
> return -ENXIO;
>
> blah, blah
> ==========
>
> blah,blah will not, but should, be executed in 2.6 with a card being present.
>
> The fix mentioned above solves this bug.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix management of allocated physical pages when the architecture
page size is not 4kB since the firmware cannot cross 4K boundary.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The SAA9730 driver doesn't quite grok what the difference between an ioport
and memory mapped I/O is. It just happened to work on the one Linux
system the SAA9730 happens to spend it's misserable existence on.
drivers/net/saa9730.c: In function 'evm_saa9730_enable_lan_int':
drivers/net/saa9730.c:68: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:70: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:72: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'evm_saa9730_disable_lan_int':
drivers/net/saa9730.c:78: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:80: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'evm_saa9730_clear_lan_int':
drivers/net/saa9730.c:85: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'evm_saa9730_block_lan_int':
drivers/net/saa9730.c:91: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'evm_saa9730_unblock_lan_int':
drivers/net/saa9730.c:97: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'show_saa9730_regs':
drivers/net/saa9730.c:150: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_allocate_buffers':
drivers/net/saa9730.c:292: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:295: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:302: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:305: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:312: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_cam_load':
drivers/net/saa9730.c:329: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:332: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_mii_init':
drivers/net/saa9730.c:369: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:395: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:403: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:410: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:432: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_control_init':
drivers/net/saa9730.c:470: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:474: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:478: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:484: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:487: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:490: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:493: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_stop':
drivers/net/saa9730.c:505: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:508: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:510: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_dma_init':
drivers/net/saa9730.c:536: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_start':
drivers/net/saa9730.c:556: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:560: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:564: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:567: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_tx':
drivers/net/saa9730.c:590: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_rx':
drivers/net/saa9730.c:664: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:729: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_write':
drivers/net/saa9730.c:848: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_set_multicast':
drivers/net/saa9730.c:943: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:949: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
Fixed by using writel instead of outl. 42 warnings less.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This reverts commit 18babd3854.
Michael Barkowski points out that it's wrong, and I agree. The
patch causes a problem rather than fixes one after another
patch "ucc_geth: Fix BD processing" was applied. Before that
patch, current packet should be blocked. However after the patch
current packet is ok and we only need to block next.
Reported-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Under rare conditions, the MAC might hang while generating a pause frame.
This patch fine tunes the MAC settings to avoid the issue, allows for
periodic MAC state check, and triggers a recovery if hung.
Also fix one MAC statistics counter for the rev board T3B2.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver attempts to upgrade the FW if the card has the wrong version.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We assign the return value of register_netdev to i, but return rc later
on. Fix it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rather than a workqueue and a per-board mutex to control PHY,
use a tasklet and spinlock. Tasklet is lower overhead and works
just as well for this.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Wheen a port on the skge driver is not used, it should
mask off interrupts from theat port.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The skge driver will deadlock if gets a transmit timeout
because the netif_tx_lock() is already held.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With 42101001.sb firmwares, we need a 10 ms delay between firmware chunks
upload on irda-usb.
Patch from Nigel Williams <nigelw@elder-gods.net>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The airo driver leaks memory if request_irq() fails.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During testing of bcm43xx interference mitigation, two problems were
discovered:
(1) When the MANUALWLAN mode was set, routines _stack_save and _stack_restore
generated assertions that were traced to saving ILT registers with addresses
> 0xFFF. This problem was fixed by adding one bit to the field used for
the offset, and subtracting one bit from the space used for the id.
(2) In MANUALWLAN mode, the IRQ XMIT errors are generated. The cause of these
errors has not yet been located. Any suggestions on debugging this problem
would be greatly appreciated.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the poll routine for the natsemi driver so that if the
driver detects an RX state machine lockup then no interrupts will be
lost while the driver recovers from that.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The interrupt status register for the natsemi chips is clear on read and
was read unconditionally from both the interrupt and from the NAPI poll
routine, meaning that if the interrupt service routine was called (for
example, due to a shared interrupt) while a NAPI poll was scheduled
interrupts could be missed. This patch fixes that by ensuring that the
interrupt status register is only read by the interrupt handler when
interrupts are enabled from the chip.
It also reverts a workaround for this problem from the netpoll hook and
improves the trace for interrupt events.
Thanks to Sergei Shtylyov <sshtylyov@ru.mvista.com> for spotting the
issue, Mark Huth <mhuth@mvista.com> for a simpler method and Simon
Blake <simon@citylink.co.nz> for testing resources.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The natsemi drivers include functions for enabling and disabling
interrupts from the chip but these are not used in all code paths. This
patch changes the code paths that touch the interrupt enable register to
use the functions. In all cases this adds an extra PCI read to post the
operation but since none of these are in fast paths this shouldn't be
too much of a problem.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: This will fix a softlock seen on some machines.
The reason was too much time was spent waiting for hardware access
to go through.
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Set the MTU for the right port depending upon the port number
for XG cards.
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When bonding does fail over it calls set_mac_address. When this happens
as the result of another port going down, the phy_mutex that is common to
both ports is held, so it deadlocks. Setting the address doesn't need to do
anything that needs the phy_mutex, it already has the RTNL to protect against
other admin actions.
This change just disables the receiver to avoid any hardware confusion
while address is changing.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NB: driver is choke-full of code that will break on big-endian; as long
as the hardware is onboard-only we can live with that, but sooner or
later that'll need fixing.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
used by ->attach() in pcmcia analog
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Building ibmtr as a module produces a spectacular pile of modpost warnings:
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x450) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x454) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x458) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x45c) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x4e8) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x4ec) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x4f0) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x4f4) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:find_turbo_adapters from .text between 'ibmtr_probe_card' (at offset 0x500) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:find_turbo_adapters from .text between 'ibmtr_probe_card' (at offset 0x504) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:find_turbo_adapters from .text between 'ibmtr_probe_card' (at offset 0x508) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:find_turbo_adapters from .text between 'ibmtr_probe_card' (at offset 0x50c) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x520) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x524) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x528) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x534) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data: from .text between 'ibmtr_probe_card' (at offset 0x540) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data: from .text between 'ibmtr_probe_card' (at offset 0x544) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data: from .text between 'ibmtr_probe_card' (at offset 0x548) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data: from .text between 'ibmtr_probe_card' (at offset 0x54c) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x558) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x55c) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x560) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x564) and 'ibmtr_reset_timer'
Fix by making ibmtr_probe an __init function.
While at it, move move ibmtr_probe_card below ibmtr_probe so the protoype
for ibmtr_probe can be deleted.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/tokenring/ibmtr.c | 25 ++++++++++++-------------
1 file changed, 12 insertions(+), 13 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/3c59x.o - Section mismatch: reference to .init.text: from .text between 'vortex_eisa_probe' (at offset 0x4580) and 'vortex_eisa_remove'
WARNING: drivers/net/3c59x.o - Section mismatch: reference to .init.text: from .text between 'vortex_eisa_probe' (at offset 0x4584) and 'vortex_eisa_remove'
WARNING: drivers/net/3c59x.o - Section mismatch: reference to .init.text: from .text between 'vortex_eisa_probe' (at offset 0x4588) and 'vortex_eisa_remove'
WARNING: drivers/net/3c59x.o - Section mismatch: reference to .init.text: from .text between 'vortex_eisa_probe' (at offset 0x458c) and 'vortex_eisa_remove'
Fixed by:
o move definition of vortex_eisa_driver below the functions it references.
o remove now unnecessary prototypes for vortex_eisa_probe and
vortex_eisa_remove.
o Make vortex_eisa_probe an __init function.
o Make vortex_eisa_remove a __devexit function.
o Wrap vortex_eisa_driver reference to vortex_eisa_remove with
__devexit_p().
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/3c59x.c | 28 +++++++++++++---------------
1 file changed, 13 insertions(+), 15 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We must exit immediately on a FIFO fill not take the end of packet path
otherwise each underrun in PIO transmit mode causes a runt packet and the
data is lost.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Initialize the timer with the rest of the private-struct.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Added during bf793295e1
The current code requests a reset but prohibits autoneg, 1000 Mb/s,
100 Mb/s and full duplex. The 8168 does not like it at all.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Yukon FE, occasional hardware receive checksum errors are seen.
An early indication of the problem is single bit differences in the two
checksum engines. Use this as a detection mechanism to turn off Rx
checksumming.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add a wc_enabled flag in the myri10ge_priv instead of relying
on mtrr >= 0.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Do not use 4k rdma request on SGI TIOCE chipset since this
bridge does not support it.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allocate a specific page and use pci_map_page for dma test instead
of relying on another existing buffer.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a missing error check in myri10ge_allocate_rings() and set status
to -ENOMEM before all actual allocations so that the error path returns
what it should.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
CC [M] drivers/net/netxen/netxen_nic_hw.o
drivers/net/netxen/netxen_nic_hw.c: In function 'netxen_nic_hw_resources':
drivers/net/netxen/netxen_nic_hw.c:231: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'dma_addr_t'
drivers/net/netxen/netxen_nic_hw.c:250: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'dma_addr_t'
u64 is unsigned long so the cast to u64 will result in a warning on the
printf arguments for 64-bit builds. So cast to unsigned long long instead.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch sets avoid_D3 for BIOSes known to be broken. Said BIOSes fail
at PXE boot if the chip is in power state D3.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In the bcm43xx interrupt handler, sanity checks are wrongly done before the
verification that the interrupt is for the bcm43xx.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The frequency to channel routine in bcm43xx requires that the frequency
be in MHz, but that condition is not always met. This patch does the
necessary conversion.
Signed-off-by: Joerg Sommer <joerg@alea.gnuu.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are three errors in the transcription of the latest revision to the
B6PHY init specifications.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/sis900.c: In function 'sis900_reset_phy':
drivers/net/sis900.c:972: warning: 'status' may be used uninitialized in this function
drivers/net/sis900.c: In function 'sis900_check_mode':
drivers/net/sis900.c:1431: warning: 'status' may be used uninitialized in this function
drivers/net/sis900.c: In function 'sis900_timer':
drivers/net/sis900.c:1467: warning: 'status' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We were using the platform_device.id field to identify which ethernet
port is used for mv643xx_eth device. This is not generally correct.
It will be incorrect, for example, if a hardware platform uses a single
port but not the first port. Here, we add an explicit port_number field
to struct mv643xx_eth_platform_data.
This makes the mv643xx_eth_platform_data structure required, but that
isn't an issue since all users currently provide it already.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PCnet32 driver always passed the the size of the largest possible packet
to the pci_dma_sync_single_for_cpu and pci_dma_sync_single_for_device.
This results in a fairly large "colateral damage" in the caches and makes
the flush operation itself much slower. On a system with a 40MHz CPU this
patch increases network bandwidth by about 12%.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Handle pci_enable_device() failure while resuming, we can safely exit here.
Signed-off-by: Monakhov Dmitriy <dmonakhov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a oops on module removal due to deallocating memory before unregistring
driver Fix a NULL pointer dereference when dev_alloc_skb fails
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a typo, wrap lines on 80-th column, change KERN_ERR to KERN_INFO for
link status message
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Revert 7628b0a8c0. Thomas Bachler
reports:
Commit 7628b0a8c0 (drivers/net/tulip/dmfe:
support basic carrier detection) breaks networking on my Davicom DM9009.
ethtool always reports there is no link. tcpdump shows incoming packets,
but TX is disabled. Reverting the above patch fixes the problem.
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Thomas Bachler <thomas@archlinux.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix broken BD processing code.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix two issues in this driver's netpoll path: one usual, with spin_unlock_irq()
enabling interrupts which nobody asks it to do (that has been fixed recently in
a number of drivers) and one unusual, with poll_controller() method possibly
causing loss of interrupts due to the interrupt status register being cleared
by a simple read and the interrpupt handler simply storing it, not accumulating.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In active-backup mode, the current bonding code duplicates IGMP
traffic to all slaves, so that switches are up to date in case of a
failover from an active to a backup interface. If bonding then fails
back to the original active interface, it is likely that the "active
slave" switch's IGMP forwarding for the port will be out of date until
some event occurs to refresh the switch (e.g., a membership query).
This patch alters the behavior of bonding to no longer flood
IGMP to all ports, and to issue IGMP JOINs to the newly active port at
the time of a failover. This insures that switches are kept up to date
for all cases.
"GOELLESCH Niels" <niels.goellesch@eurocontrol.int> originally
reported this problem, and included a patch. His original patch was
modified by Jay Vosburgh to additionally remove the existing IGMP flood
behavior, use RCU, streamline code paths, fix trailing white space, and
adjust for style.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ARP validation code only needs ARPs for the bonding device.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bonding can erroneously register the same packet_type to receive
ARPs (for use by ARP validation): once at device open time, and once via
sysfs. Since sysfs can change the validate setting (and thus register
or unregister) at any time, a flag is needed to synchronize with device
open in order to avoid double registrations, and the simplest place is
within the packet_type structure itself. Double unregister is not an
issue.
Bug reported by Ulrich Oelmann <ulrich.oelmann@web.de>.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I recognized a compile error in latest git:
/here/workdir/git/drivers/net/gianfar.c: In function `gfar_vlan_rx_kill_vid':
/here/workdir/git/drivers/net/gianfar.c:1135: error: structure has no member named `vgrp'
This error was introduced in commit:
commit 6d04e3b04b
...
[VLAN]: Avoid a 4-order allocation.
Signed-off-by: Jan Altenberg <jan@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch splits the vlan_group struct into a multi-allocated struct. On
x86_64, the size of the original struct is a little more than 32KB, causing
a 4-order allocation, which is prune to problems caused by buddy-system
external fragmentation conditions.
I couldn't just use vmalloc() because vfree() cannot be called in the
softirq context of the RCU callback.
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switching HDLC devices from Ethernet-framing mode caused stale ethernet
function assignments within net_device.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is based on the assumption that an interface's ifindex is basically
an alias for a local MAC address, so incoming packets now are matched
to sockets based on remote MAC, session id, and ifindex of the
interface the packet came in on/the socket was bound to by connect().
For relayed packets, the socket that's used for relaying is selected
based on destination MAC, session ID and the interface index of the
interface whose name currently matches the name requested by userspace
as the relaying source interface.
Signed-off-by: David S. Miller <davem@davemloft.net>
The information contained within platform_data should be self-contained.
Replace the pointer to a MAC address with the actual MAC address in
struct mv643xx_eth_platform_data.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commit 908b637fe7 removed ETH_DMA_ALIGN
but missed a usage of it in a macro, which broke the build.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This missing line caused transmit errors on the Qlogic 4032 chip.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix copyright and license ("regents" should not have ever been used).
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
No need to stop tc35815 before resetting the board. This fixes the
build of tc35815 as a module. This also means there is no caller of
tc35815_killall left, so remove that function also.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
BCM4309 devices aren't working properly as A PHYs aren't supported
yet, but we probe 802.11a cores anyway. This fixes it, while still
allowing for A PHY code to be developed in the future.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Compiler warning spots real error!
The function do_rom_fast_read called in do_rom_fast_write can fail
and leave data1 unset. This causes a compile warning.
The correct thing is to propagate the error out.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bob Tracy <rct@gherkin.frus.com> reported that the addition of support
for Aculab E1/T1 cPCI carrier cards broke detection of vanilla natsemi
cards. This patch fixes that: the problem is that the driver-specific
ta in the PCI device table is an index into a second table and this
had not been updated for the vanilla cards.
This patch fixes the problem minimally.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Chelsio without NAPI enabled has been broken (won't compile) since
3de00b89 ("chelsio: NAPI speed improvement"):
drivers/net/chelsio/sge.c: In function `t1_interrupt`:
drivers/net/chelsio/sge.c:1716: error: `Q` undeclared (first use in this function)
The change below seems to add back in the declaration and
initialization of `Q` that was removed by mistake, and at least makes
the driver compile for me, although I have no hardware and hence no
way to test whether this actually works.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve the traffic recovery after the HW ran out of response queue entries.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Offload packets may be DMAed long after their SGE Tx descriptors are done
so they must remain mapped until they are freed rather than until their
descriptors are freed. Unmap such packets through an skb destructor.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sysfs attributes are now managed per port, no longer per adapter.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Restore in s2io_reset, the mac address assigned during s2io_open.
Earlier, it was getting overwritten to the factory default (read from the
eeprom) and subsequently dropping received frames.
- Fixed the typo in calling rtnl_unlock in s2io_set_link function.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Enhanced Statistics are supported only for Xframe II (Herculas) card. Add
condition check such Enhanced statistics will included only in the case of
Xframe II card.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Turning off LED for LINK_DOWN notification
- Return from rxd_owner_bit_reset function if call to set_rxd_buffer_pointer
fails with ENOMEM
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Added code to not to strip vlan tag when driver is in promiscuous mode
- Added module loadable parameter 'vlan_tag_strip" through which user can
enable or disable vlan stripping irrespective of mode
( promiscuous or non-promiscuous ).
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Optimized delay to wait for command completion so as to reduce the
initialization wait time.
- Disable differentiated services steering. By default RMAC is configured to
steer traffic with certain DS codes to other queues. Driver must initialize
the DS memory to 0 to make sure that DS steering will not be used by default.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Added debug statements to print a debug message if the MSI/MSI-X vector (or)
data is zero.
- This patch removes the code that will enable NAPI for the case of single
ring and MSI-X / MSI case. There are some issue in the enabling NAPI with
MSI/MSI-X. So we are turning off NAPI in the case of MSI/MSI-X.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
To reproduce this panic consistently, we run an intensive network
application like 'netperf'. After waiting for a couple of seconds,
you will see a stack trace and a kernel panic where we are calling
pci_unmap_single() in ql_poll().
Changes:
1) Check the flags on the Response MAC IO Control block to check for
errors
2) Ensure that if we are on the 4022 we only use one segment
3) Before, we were reading the memory mapped producer index register
everytime we iterated in the loop when clearing the queue. We should
only be iterating to a known point, not as the producer index
is being updated.
Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
To Reproduce the Problem:
To reproduce this panic consistently, we run an intensive network
application like 'netperf' and then switch to a different console.
After waiting for a couple of seconds, you will see a tx reset has occured.
Reason:
We enable interrupts even if we were not running.
Solution:
Now we will enable interrupts only after we are ready to give up the poll
routine.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pci_map_single() could fail. We need to properly check the return
code from pci_map_single(). If we can not properly map this address,
then we should cleanup and return the proper return code.
Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The scatter/gather lists were not being build correctly. When
large frames spanned several buffers the chip would panic.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This change removes use of constants for rx buffer queue size
and instead calculates the queue length based on what he MTU
is set to.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This network device driver shares the same hardware as the qla4xxx
iSCSI driver. Changing the MTU via the device interface will
cause qla4xxx to crash as there is no way to make notification.
Users wishing to change the MTU must do so using an iSCSI
utility such as Qlogic SanSurfer. This forces the user to
unload/reload this network device driver after the MTU
value has been changed in flash.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
1) Fix deadlock issue when in QL_RESET_ACTIVE state and traversing
through the Link State Machine
2) Fix deadlock issue when ethtool would call ql_get_settings()
3) Fix deadlock issue when adaptor is ifup'ed but adaptor fails to initialize
Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We do not need to zero out the 64 byte MAC request I/O control block.
By zeroing out the control block and setting it to proper fields is
redundant work. This is because in the qla3xxx_send() function we will
already set the proper fields in this structure. The unused fields are
not looked at by the hardware and do not need to be zeroed out.
Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The return code was not properly set when when allocating memory or mapping
memory failed. Depending on the stack, the return code would sometimes
return 0, which indicates everything was ok, when in fact there was an error.
This would cause trouble when the module was removed. Now, we will pass
back the proper return code when an error occurs during the PCI probe.
Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver contains this little piece of candy:
#if defined(CONFIG_DMA_NONCOHERENT) || defined(CONFIG_NOT_COHERENT_CACHE)
#define ETH_DMA_ALIGN L1_CACHE_BYTES
#else
#define ETH_DMA_ALIGN 8
#endif
Any reason why we're not using dma_get_cache_alignment() instead?
Ralf
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update ucc_geth_probe() to use function of_get_mac_address() to obtain the MAC
address.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It looks like the skge driver inherited another bug from the sk98lin code.
If I send from 1000mbit port to a machine on 100mbit port, the switch should
be doing hardware flow control, but no pause frames show up in the statistics.
This is the analog of the recent sky2 fixes. The device needs to listen
for multicast pause frames and then not discard them.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Work around a bug which occurs when adopting firmware versions
1.4.4 though 1.4.11 where broadcasts are filtered as if they
were multicasts.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Multiple threads performing a transmit can race into
the spidernet tx ring cleanup code. This puts the
relevant check under a lock.
Signed-off-by: Linas Vepstas <lins@austin.ibm.com>
Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It appears that under certain circumstances, a race will result
in a double-free of an skb. This patch null's out the skb pointer
upon the skb free, avoiding the inadvertent deref of bogus data.
The next patch fixes the actual race.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch separates the hardware descriptor state from the
driver descriptor state, per (old) suggestion from Ben Herrenschmidt.
This compiles and boots and seems to work.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This moves the medium variable into the spidernet card structure.
It renames the GMII_ variables to BCM54XX specific ones.
Signed-off-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patches removes logging for SPIDER_NET_GTMFLLINT interrupts.
Since the interrupts are not irregular, and they happen frequently
when using 100Mbps network switches.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds or changes some HW specific settings for spider_net on
Celleb.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch moves calling init_firmware() from spider_net_probe() to
spider_net_open() so as to use the driver by built-in.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add auto negotiation support for Celleb.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As of 2.6.20-git4, the spider_net driver does not compile.
This appears to be due to some archaic usage involving kobjects.
It also fixes a nasty double-free during ifdown of the interface.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This version moves the medium variable to the card specific structure and
changes the GMII_* to BCM54XX_* #defines.
This patch adds improved version of enable_fiber for both the 5421 and
the 5461 phy. It is now possible to specify with these wether you want
autonegotiation or not. This is needed for bladecenter switches where
some expect autonegotiation and some dont seem to like this at all.
Depending on this flag it sets phy->autoneg accordingly for the fiber mode.
More importantly it implements proper read_link and poll_link functions
for both phys which can handle both copper and fiber mode by determining
the medium first and then branching to the required functions. For fiber
they all work fine, for copper they are not tested but return the result
of the genmii_* function anyway which is supposed to work.
The patch moves the genmii_* functions around to avoid foreward declarations.
Signed-off-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch removes checksum offload feature in mcp65 chipsets as they
are not supported in hw.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There seems to be an issue when both MSI-X is enabled and NAPI is
configured. This patch disables MSI-X until the issue is root caused.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The napi poll routine was missing the call to the optimized rx process
routine. This patch adds the missing call for the optimized path.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* clear_page() use is wrong. We might have multiple pages.
Use memset() instead.
* Call pci_unregister_driver() in module exit.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/pub/scm/linux/kernel/git/kyle/parisc-2.6: (78 commits)
[PARISC] Use symbolic last syscall in __NR_Linux_syscalls
[PARISC] Add missing statfs64 and fstatfs64 syscalls
Revert "[PARISC] Optimize TLB flush on SMP systems"
[PARISC] Compat signal fixes for 64-bit parisc
[PARISC] Reorder syscalls to match unistd.h
Revert "[PATCH] make kernel/signal.c:kill_proc_info() static"
[PARISC] fix sys_rt_sigqueueinfo
[PARISC] fix section mismatch warnings in harmony sound driver
[PARISC] do not export get_register/set_register
[PARISC] add ENTRY()/ENDPROC() and simplify assembly of HP/UX emulation code
[PARISC] convert to use CONFIG_64BIT instead of __LP64__
[PARISC] use CONFIG_64BIT instead of __LP64__
[PARISC] add ASM_EXCEPTIONTABLE_ENTRY() macro
[PARISC] more ENTRY(), ENDPROC(), END() conversions
[PARISC] fix ENTRY() and ENDPROC() for 64bit-parisc
[PARISC] Fixes /proc/cpuinfo cache output on B160L
[PARISC] implement standard ENTRY(), END() and ENDPROC()
[PARISC] kill ENTRY_SYS_CPUS
[PARISC] clean up debugging printks in smp.c
[PARISC] factor syscall_restart code out of do_signal
...
Fix conflict in include/linux/sched.h due to kill_proc_info() being made
publicly available to PARISC again.
1. Add race condition check after netif_stop_queue(). tg3_tx() runs
without netif_tx_lock and can race with tg3_start_xmit_dma_bug() ->
tg3_tso_bug().
2. Firmware TSO in 5703/5704/5705 also have the same TSO limitation,
i.e. they cannot handle TSO headers bigger than 80 bytes. Rename
TG3_FL2_HW_TSO_1_BUG to TG3_FL2_TSO_BUG and set this flag on
these chips as well.
3. Update version to 3.74.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d2ed16356f.
As Thomas Gleixner reports:
"e1000 is not working anymore. ifup fails permanentely.
ADDRCONF(NETDEV_UP): eth0: link is not ready
nothing else"
The broken commit was identified with "git bisect".
Auke Kok says:
"I think we need to drop this now. The report that says that this
*fixes* something might have been on regular interrupts only. I
currently suspect that it breaks all MSI interrupts, which would make
sense if I look a the code. Very bad indeed."
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (21 commits)
natsemi: Support Aculab E1/T1 PMXc cPCI carrier cards
natsemi: Add support for using MII port with no PHY
skge: race with workq and RTNL
Replace local random function with random32()
s2io: RTNL and flush_scheduled_work deadlock
8139too: RTNL and flush_scheduled_work deadlock
sis190: RTNL and flush_scheduled_work deadlock
r8169: RTNL and flush_scheduled_work deadlock
[PATCH] ieee80211softmac: Fix setting of initial transmit rates
[PATCH] bcm43xx: OFDM fix for rev 1 cards
[PATCH] bcm43xx: Fix for 4311 and 02/07/07 specification changes
[PATCH] prism54: correct assignment of DOT1XENABLE in WE-19 codepaths
[PATCH] zd1211rw: Readd zd_addr_t cast
[PATCH] bcm43xx: Fix for oops on resume
[PATCH] bcm43xx: Ignore ampdu status reports
[PATCH] wavelan: Use ARRAY_SIZE macro when appropriate
[PATCH] hostap: Use ARRAY_SIZE macro when appropriate
[PATCH] misc-wireless: Use ARRAY_SIZE macro when appropriate
[PATCH] ipw2100: Use ARRAY_SIZE macro when appropriate
[PATCH] bcm43xx: Janitorial change - remove two unused variables
...
Remove the use of CONFIG_MV643XX_ETH_[012] variables on most platforms.
Instead, platform-specific code enables the ports supported by the
hardware. After this patch, these config variables are only used in
arch/ppc, so also move them from drivers/net/Kconfig to arch/ppc/Kconfig.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Paul Mackerras <paulus@samba.org>
Aculab E1/T1 PMXc cPCI carrier card cards present a natsemi on the cPCI
bus with an oversized EEPROM using a direct MII<->MII connection with no
PHY. This patch adds a new device table entry supporting these cards.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch provides code paths which allow the natsemi driver to use the
external MII port on the chip but ignore any PHYs that may be attached to it.
The link state will be left as it was when the driver started and can be
configured via ethtool. Any PHYs that are present can be accessed via the MII
ioctl()s.
This is useful for systems where the device is connected without a PHY
or where either information or actions outside the scope of the driver
are required in order to use the PHYs.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If a workqueue function that needs RTNL is running when skge_down
is called then a deadlock is possible. Fix by only clearing the timer,
and handling the flush_scheduled_work on removal. This work queue is only
ever used for the old fiber based boards.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mantra: don't use flush_scheduled_work with RTNL held.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Your usual dont-flush_scheduled_work-with-RTNL-held stuff.
It is a bit different here since the thread runs permanently
or is only occasionally kicked for recovery depending on the
hardware revision.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
flush_scheduled_work() in net_device->close has a slight tendency
to deadlock with tasks on the workqueue that hold RTNL.
rtl8169_close/down simply need the recovery tasks to not meddle
with the hardware while the device is going down.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
Documentation/kernel-docs.txt update.
arch/cris: typo in KERN_INFO
Storage class should be before const qualifier
kernel/printk.c: comment fix
update I/O sched Kconfig help texts - CFQ is now default, not AS.
Remove duplicate listing of Cris arch from README
kbuild: more doc. cleanups
doc: make doc. for maxcpus= more visible
drivers/net/eexpress.c: remove duplicate comment
add a help text for BLK_DEV_GENERIC
correct a dead URL in the IP_MULTICAST help text
fix the BAYCOM_SER_HDX help text
fix SCSI_SCAN_ASYNC help text
trivial documentation patch for platform.txt
Fix typos concerning hierarchy
Fix comment typo "spin_lock_irqrestore".
Fix misspellings of "agressive".
drivers/scsi/a100u2w.c: trivial typo patch
Correct trivial typo in log2.h.
Remove useless FIND_FIRST_BIT() macro from cardbus.c.
...
sk98lin is scheduled for removal in July 2007. This patch makes the
deprecation more obvious in the configuration interface. FWIW, Gentoo have
been shipping a patch very similar to this for a long time.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Comtrol Hostess SV-11 driver uses features from INET but doesn't depend on it.
The simple solution is to make it depend on INET as happens for the sealevel
driver.
Fixes bug #7930.
Signed-Off-By: Baruch Even <baruch@ev-en.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Arnaldo Carvalho de Melo