Making sure we match the actual register names.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current code assumes that DMA is finished before SD access end is
flagged. Thus, it schedules the 'dma_complete' tasklet in the SD card
interrupt routine when DATAEND is set. The assumption is not safe,
though. Even by mounting an SD card, it can be seen that sometimes DMA
complete is first, sometimes DATAEND. It seems they are usually close
enough timewise to not cause problems. However, a customer reported that
with CMD53 sometimes things really break apart. As a result, the BSP has
a patch which introduces flags for both events and makes sure both flags
are set before scheduling the tasklet. The customer accepted the patch,
yet it doesn't seem a proper upstream solution to me.
This patch refactors the code to replace the tasklet with already
existing and more lightweight mechanisms. First of all, we set the
callback in a DMA descriptor to automatically get notified when DMA is
done. In the callback, we then use a completion to make sure the SD
access has already ended. Then, we proceed as before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before enabling SDIO irqs, clear the status bit, so we discard old and
stale interrupts. Needed to get two wireless cards working. Use the
newly introduced macro in all places.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
An mmc host driver shouldn't rely on interrupt.h being included by another
public mmc header. Instead make that dependency explicit by including
interrupt.h in those host drivers that depends on it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add tuning support for use with SDR104 mode
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the r7s72100 SOC, the DATA_PORT register was changed to 32-bits wide.
Therefore a new flag has been created that will allow 32-bit reads/writes
to the DATA_PORT register instead of 16-bit (because 16-bits accesses are
not supported).
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need to add R1 without CRC support, refactor the bus width routine a
little and extend a quirk check. To support "non-removable;" we need a
workaround which will be hopefully removed when reworking PM soon.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
card_busy is only used/tested on SDHI for R-Car Gen2 and later.
Move it to the SDHI driver, so we can then activate it conditionally
depending on the SDHI type.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sparse complains about the implicit cast. Making it explicit is indeed
better coding style.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that reading CTL_STATUS is consistent, we can remove CTL_STATUS2 and
document how this is handled internally.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This bit has a different meaning in SDHI and original TMIO. Document
that and use the proper naming.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To prevent confusion, use the virtual u32 CTL_STATUS in card_busy() the
same way as in other parts of this driver.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
BIT() makes it easier to match the bits to the datasheet. This is
especially important here, since some variants have different names in
their datasheets (like with Renesas R-Car).
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Looking at the backlogs, I am not the only one who missed that the above
functions do not read u32 from one register, but create a virtual u32
from reading to adjacent u16 registers (which depending on 'bus_shift'
can be up to 8 byte apart). Because this driver supports old hardware
for which we don't have documentation, I first wrongly assumed there was
a variant which had a few u32 registers. Let's give the functions more
descriptive names to make it more obvious what is happening.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no reason to have a public and private header file. Merge them
into a private one, so looking up symbols is less confusing.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We removed installation of separate handlers previously, so we can also
remove the separate handlers.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Based on work by Shinobu Uehara and Ben Dooks. This adds the voltage
switch operation needed for all UHS-I modes, but not the tuning needed
for SDR-104 which will come later.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently tmio_mmc assumes that the input clock frequency is fixed and
only its own clock divider can be changed. This is not true in the
case of sh_mobile_sdhi; we can use the clock API to change it.
In tmio_mmc:
- Delegate setting of f_min from tmio to the clk_enable operation (if
implemented), as it can be smaller than f_max / 512
- Add an optional clk_update operation called from tmio_mmc_set_clock()
that updates the input clock frequency
- Rename tmio_mmc_clk_update() to tmio_mmc_clk_enable(), to avoid
confusion with the clk_update operation
In sh_mobile_sdhi:
- Make the setting of f_max conditional; it should be set through the
max-frequency property in the device tree in future
- Set f_min based on the input clock's minimum frequency
- Implement the clk_update operation, selecting the best input clock
frequency for the bus frequency that's wanted
sh_mobile_sdhi_clk_update() is loosely based on Kuninori Morimoto's work
in sh_mmcif.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change the clk_enable operation to take a pointer to the struct
tmio_mmc_host and have it set f_max. For consistency, also change the
clk_disable operation to take a pointer to struct tmio_mmc_host.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dma_request_slave_channel_compat() in tmio_mmc_dma
needs .chan_priv_tx/.chan_priv_rx. But these are copied from
sh_mobile_sdhi only, and sh_mobile_sdhi_info is now almost
same as tmio_mmc_data except .chan_priv_?x.
sh_mobile_sdhi_info can be replaced to tmio_mmc_data, but it is
used from ${LINUX}/arch/arm/mach-shmobile, ${LINUX}/arch/sh.
So, this patch adds .chan_priv_?x into tmio_mmc_data as 1st step,
and sh_mobile_sdhi driver has dummy operation for now.
It will be replaced/removed together with platform data replace.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Current tmio_mmc sets dma_slave_config :: slave_id field for DMAEngine,
but it is no longer needed. Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Renesas SDHI which is based on TMIO driver has 2 type SoC. 1st one is
used as SH-Mobile series, and 2nd is R-Car series. R-Car series SoC has
DMA buswidth setting register which enables 32bit access.
This patch adds .dma_buswidth and enables it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some controllers need DMA special register/setting.
This patch adds new .enable_dma callback for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .dma_rx_offset is implemented under tmio_mmc_dma.
It goes to tmio_mmc_data by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .alignment_shift is implemented under tmio_mmc_dma.
It goes to tmio_mmc_data by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .bus_shift is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .multi_io_quirk is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .clk_disable is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .clk_enable is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .write16_hook is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .dma is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current tmio_mmc driver is using tmio_mmc_data for driver/platform
specific data/callback, and it is needed for tmio_mmc_host_probe()
function. Because of this style, include/linux/mfd/tmio.h header has
tmio driver/framework specific data which is not needed from platform.
This patch adds new tmio_mmc_host_alloc/free() as cleanup preparation.
tmio driver specific data/callback will be implemented in tmio_mmc_host,
and platform specific data/callback will be implemented in tmio_mmc_data
in this cleanup.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These library functions aren't used and nor needed, let's remove them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
To give the option for tmio hosts to use the runtime PM callbacks for
CONFIG_PM_SLEEP as well as CONFIG_PM_RUNTIME, move them to CONFIG_PM.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add clock gating control as a part of the tmio library functions for
runtime PM.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
An internal power state machine were beeing used to keep ->probe() and
->set_ios() in sync. Especially for handling specific scenarios while
using CONFIG_MMC_CLKGATE. Moreover dependency to CONFIG_MMC_CLKGATE
existed to handle runtime PM properly, which we moves away from here.
By removing the state machine and instead make ->set_ios() rely on the
information provided through the function's in-parameters, the code
becomes significantly simplier.
Additonally as a part of this rework we prepares for making the runtime
PM callbacks responsible of clock gating.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
The host must be kept active to be able to serve SDIO IRQs, thus let's
prevent it from going inactive while SDIO IRQ is enabled.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Since the users of the exported PM functions are now using the modern
PM ops macros, we can convert to the proper corresponding PM configs.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <chris@printf.net>
.bus_shift is used to 16/32bit register access offset calculation on
tmio driver. tmio_mmc_xxx is used from Toshiba/Renesas now, but this
bus_shift value depends on HW IP. This patch moves .bus_shift to
tmio_mmc_data member and sets it on each driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
With MMC clock gating enabled the MMC core currently calls MMC host driver's
.set_ios() method with .power_mode == MMC_POWER_ON and the clock value set
either to 0 or to the target rate. The tmio MMC driver then wrongly
translates the latter calls to card slot power-on requests, even when the
slot already was on. This patch fixes the driver to avoid needlessly
incrementing power-supplying regulator's use count.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When resuming, the tmio_mmc_host_resume() function is run when the
controller might still be powered down. Issuing a reset command to it at
that time has no effect. This patch postpones resetting the controller
until the first powering-up .set_ios() call.
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The sdio_irq_enabled member of struct tmio_mmc_host is a left-over from the
previously removed SDIO IRQ workaround. It is no longer needed and can now
be removed too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The controller power status flag does not have to be accessed from the
hot-plug detection code any more, it can now be removed from the platform
data and put in the controller private struct.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
If the platform specifies the TMIO_MMC_HAS_COLD_CD flag, use the generic
MMC GPIO card hotplug helper.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The condition, whether we have to use the native TMIO card hotplug
detection interrupt, is rather complex, it is better to only calculate it
once and store in the private data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
When DMA is in use and the card is ejected during IO, DMA transfers have to
be terminated, otherwise the dmaengine driver fails to operate properly,
when the card is re-inserted.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Wolfram Sang