The existing support for hardware-assisted RTS/CTS is rudimentary and
doesn't work.
Add support for hardware-assisted RTS/CTS hardware flow control for the
(H)SCIF, SCIFA, and SCIFB variants.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before, the driver relied on initialization by the boot loader, or by
implicit reset state.
Note that unlike on (H)SCIF, the RTS/CTS bits exist only if dedicated
RTS/CTS pins are available, which depends on the SoC and UART instance.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct pin initialization on (H)SCIF:
- RTS must be deasserted (it's active low),
- SCK must be an input, as it may be used as the optional external
clock input.
Initial pin configuration must always be done:
- Regardless of the presence of dedicated RTS and CTS pins: if the
register exists, the RTS/CTS bits exist, too,
- Regardless of hardware flow control being enabled or not: RTS must
be deasserted.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace open-coded variants of sci_getreg() by function calls, and drop
intermediate variables where appropriate.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enhance the Renesas SCI UART driver to add support for GPIO-controlled
modem lines (CTS, DSR, DCD, RNG, RTS, DTR), using the serial_mctrl_gpio
helpers.
GPIO-controlled modem lines can be used when dedicated modem lines are
not available. Invalid configurations specifying both GPIO RTS/CTS and
dedicated RTS/CTS are rejected.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Documentation/serial/driver clearly states:
If the port does not support CTS, DCD or DSR, the driver should
indicate that the signal is permanently active.
Hence always set TIOCM_CTS, as we currently don't look at the CTS
hardware line state at all.
FWIW, this fixes the transmit path when hardware-assisted flow control
is enabled, and userspace enables CRTSCTS.
The receive path is still broken, as RTS is never asserted.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of commit 2eaa790989 ("earlycon: Use common framework for
earlycon declarations") it is no longer needer to specify both
EARLYCON_DECLARE() and OF_EARLYCON_DECLARE().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for sparse variable sampling rates on SCIFA and SCIFB.
According to the datasheet, sampling rate 1/5 needs a small quirk to
avoid corrupting the first byte received.
This increases the range and accuracy of supported baud rates.
E.g. on r8a7791/koelsch:
- Supports now 134, 150, and standard 500000-4000000 bps,
- Perfect match for 134, 150, 500000, 1000000, 2000000, and 4000000
bps,
- Accuracy has increased for most standard bps values.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the single sampling rate and special handling for HSCIF's
variable sampling rates by a bitmask and a custom iterator.
This prepares for the advent of SCIFA/SCIFB's sparse variable sampling
rates.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On SCIx variants different from HSCIF, the bit rate is equal to the
sampling clock rate divided by half the sampling rate. Currently this is
handled by dividing the sampling rate by two, which was OK as it was
always even.
Replace halving the sampling rate by premultiplying the base clock
frequency by 2, to accommodate odd sampling rates on SCIFA/SCIFB later.
Replace the shift value in the BRG divider calculation by a
premultiplication of the base clock frequency too, for consistency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIFA and SCIFB have additional bit rate config bits in the Serial Mode
Register. Don't touch them when using the port as a serial console, as
we rely on the boot loader to have configured the serial port config.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"earlyprintk" is architecture specific option.
General "earlycon" option support is much better.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
[uli: preserve other SCSCR bits when asserting RE and TE]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
[geert: rewording, #ifdef rework]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BSP team noticed that there is spin/mutex lock issue on sh-sci when
CPUFREQ is used. The issue is that the notifier function may call
mutex_lock() while the spinlock is held, which can lead to a BUG().
This may happen if CPUFREQ is changed while another CPU calls
clk_get_rate().
Taking the spinlock was added to the notifier function in commit
e552de2413 ("sh-sci: add platform device private data"), to
protect the list of serial ports against modification during traversal.
At that time the Common Clock Framework didn't exist yet, and
clk_get_rate() just returned clk->rate without taking a mutex.
Note that since commit d535a2305f ("serial: sh-sci: Require a
device per port mapping."), there's no longer a list of serial ports to
traverse, and taking the spinlock became superfluous.
To fix the issue, just remove the cpufreq notifier:
1. The notifier doesn't work correctly: all it does is update stored
clock rates; it does not update the divider in the hardware.
The divider will only be updated when calling sci_set_termios().
I believe this was broken back in 2004, when the old
drivers/char/sh-sci.c driver (where the notifier did update the
divider) was replaced by drivers/serial/sh-sci.c (where the
notifier just updated port->uartclk).
Cfr. full-history-linux commits 6f8deaef2e9675d9 ("[PATCH] sh: port
sh-sci driver to the new API") and 3f73fe878dc9210a ("[PATCH]
Remove old sh-sci driver").
2. On modern SoCs, the sh-sci parent clock rate is no longer related
to the CPU clock rate anyway, so using a cpufreq notifier is
futile.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Geert writes:
Summary:
- Clean up the naming of clocks in the sh-sci driver and its DT bindings,
- Add support for the optional external clock on (H)SCI(F), where this pin
can serve as a clock input,
- Add support for the optional clock sources for the Baud Rate
Generator for External Clock (BRG), as found on some SCIF variants
and on HSCIF.
All platforms that used to define an sci_fck clock have now switched to
the fck name. Remove the fallback code.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for using the Baud Rate Generator for External Clock (BRG), as
found on some SCIF and HSCIF variants, to provide the sampling clock.
This can improve baud rate range and accuracy.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for using the SCIx clock pin "(H)SCK" as an external clock
input on (H)SCI(F), providing the sampling clock.
Note that this feature is not yet supported on the select SCIFA variants
that also have it (e.g. sh7723, sh7724, and r8a7740).
On (H)SCIF variants with an External Baud Rate Generator (BRG), the
BRG Clock Select Register must be configured for the external clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the clock and baud rate parameter code to ease adding support
for multiple sampling clock sources.
sci_scbrr_calc() now returns the bit rate error, so it can be compared
to the bit rate error using other sampling clock sources.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "renesas,scif" compatible value is currently used for the SCIF
variant in all Renesas SoCs of the R-Car family. However, the variant
used in the R-Car family is not the common "SH-4(A)" variant, but a
derivative with added "Baud Rate Generator for External Clock" (BRG),
which is also present in sh7734.
Use the family-specific SCIF compatible values for R-Car Gen1, Gen2, and
Gen3 SoCs to differentiate. The "renesas,scif" compatible value can
still be used as a common denominator for SCIF variants with the
"SH-4(A)" register layout (i.e. ignoring the "Serial Extension Mode
Register" (SCEMR) and the new BRG-specific registers).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "renesas,scif" compatible value is currently used for the SCIF
variant in all Renesas SoCs of the R-Car and RZ families. However, the
variant used in the RZ family is not the common "SH-4(A)" variant, but
the "SH-2(A) with FIFO data count register" variant, as it has the
"Serial Extension Mode Register" (SCEMR), just like on sh7203, sh7263,
sh7264, and sh7269.
Use the (already documented) SoC-specific "renesas,scif-r7s72100"
compatible value to differentiate. The "renesas,scif" compatible value
can still be used as a common denominator for SCIF variants with the
"SH-4(A)" register layout (i.e. ignoring the SCEMR register).
Note that currently both variants are treated the same, but this may
change if support for the SCEMR register is ever added.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Store the encoded port and register types directly in of_device_id.data,
instead of using a pointer to a structure.
This saves memory and simplifies the source code, especially when adding
more compatible entries later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add register definitions for the Baud Rate Generator for External Clock
(BRG), as found in some SCIF and in HSCIF, including a new regtype for
the "SH-4(A)"-derived SCIF variant with BRG.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The maximum baud rate depends on the sampling rate.
HSCIF has a variable sampling rate and sets s->sampling_rate to zero,
hence use the minimum sampling rate of 8.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For low bit rates, the for-loop that reduces the divider returned by
sci_scbrr_calc() and picks the clock select value may terminate without
finding suitable values, leading to out-of-range divider and clock
select values.
sci_baud_calc_hscif() doesn't suffer from this problem, as it correctly
uses clamp().
Since there are only two relevant differences between HSCIF and other
variants w.r.t. bit rate configuration (fixed vs. variable sample rate,
and an additional factor of two), sci_scbrr_calc() and
sci_baud_calc_hscif() can be merged, fixing the issue with out-of-range
values.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When assuming D = 0.5 and F = 0, maximizing the receive margin M is
equivalent to maximizing the sample rate N.
Hence there's no need to calculate the receive margin, as we can obtain
the same result by iterating over all possible sample rates in reverse
order, and skipping parameter sets that don't provide a lower bit rate
error.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The algorithm to find the best parameters for the requested bit rate
calculates the relative bit rate error, using "(br * scrate) / 1000".
For small "br * scrate", this has two problems:
- The quotient may be zero, leading to a division by zero error,
- This may introduce a large rounding error.
Switch from relative to absolute bit rate error calculation to fix this.
The default baud rate generator values can be removed, as there will
always be one set of values that gives the smallest absolute error.
Print the best set of values when debugging.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If bps >= 1048576, the multiplication of the predivider and "bps" will
overflow, and both br and err will contain bogus values.
Skip the current and all higher clock select predividers when overflow
is detected. Simplify the calculations using intermediates while we're
at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the -1 offset of br to the assignment to *brr, so br cannot become
negative anymore, and update the clamp() call. Now all unsigned values
in sci_baud_calc_hscif() can become unsigned.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Blindly writing the default configuration value into the SCSCR register
may change the clock selection bits, breaking the serial console if the
current driver settings differ from the default settings.
Keep the current clock selection bits to prevent this from happening
on e.g. r8a7791/koelsch when support for the BRG will be added.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As F is assumed to be zero in the receive margin formula, frame_len is
not used. Remove it, together with the sci_baud_calc_frame_len() helper
function.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As no platform defines an interface clock the SCI driver always falls
back to a clock named "peripheral_clk".
- On SH platforms that clock is the base clock for the SCI functional
clock and has the same frequency,
- On ARM platforms that clock doesn't exist, and clk_get() will return
the default clock for the device.
We can thus make the functional clock mandatory and drop the interface
clock.
EPROBE_DEFER is handled for clocks that may be referenced from DT (i.e.
"fck", and the deprecated "sci_ick").
Cc: devicetree@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
[geert: Handle EPROBE_DEFER, reformat description, break long comment line]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue that the "length" of scatterlist should be
set using sg_dma_len(). Otherwise, a dmaengine driver cannot work
correctly if CONFIG_NEED_SG_DMA_LENGTH=y.
Fixes: 7b39d90184 (serial: sh-sci: Fix NULL pointer dereference if HIGHMEM is enabled)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for obtaining DMA channel information from the device tree.
This requires switching from the legacy sh_dmae_slave structures with
hardcoded channel numbers and the corresponding filter function to:
1. dma_request_slave_channel_compat(),
- On legacy platforms, dma_request_slave_channel_compat() uses
the passed DMA channel numbers that originate from platform
device data,
- On DT-based platforms, dma_request_slave_channel_compat() will
retrieve the information from DT.
2. and the generic dmaengine_slave_config() configuration method,
which requires filling in DMA register ports and slave bus widths.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Occasionally, DMA transaction completes _after_ DMA engine is stopped.
Verify if the transaction has not finished before forcing the engine to
stop and push the data
Signed-off-by: Muhammad Hamza Farooq <mfarooq@visteon.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DMA packet completion and timer expiry take place at the same time,
do not terminate the DMA engine, leading by submission of new
descriptors, as the DMA communication hasn't necessarily stopped here.
Signed-off-by: Muhammad Hamza Farooq <mfarooq@visteon.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dmaengine_submit() will not start the DMA operation, it merely adds
it to the pending queue. If the queue is no longer running, it won't be
restarted until dma_async_issue_pending() is called.
Signed-off-by: Muhammad Hamza Farooq <mfarooq@visteon.com>
[geert: Add more description]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the DMA engine is not stopped everytime rx_timer_fn is called, the
interrupts have to be redirected back to CPU only when incomplete DMA
transaction is handled
Signed-off-by: Muhammad Hamza Farooq <mfarooq@visteon.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This prevents DMA timer timeout that can trigger after the port has
been closed.
Signed-off-by: Aleksandar Mitev <amitev@visteon.com>
[geert: Move del_timer_sync() outside spinlock to avoid circular locking
dependency between rx_timer_fn() and del_timer_sync()]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to call sci_start_rx() from sci_request_dma() when DMA
setup fails, as sci_startup() will call sci_start_rx() anyway.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For DMA receive requests, the driver is only notified by DMA completion
after the whole DMA request has been transferred. If less data is
received, it will stay stuck until more data arrives. The driver
handles this by setting up a timer handler from the receive interrupt,
after reception of the first character.
Unlike SCIFA and SCIFB, SCIF and HSCIF don't issue receive interrupts on
reception of individual characters if a receive DMA request is in
progress, so the timer is never set up.
To fix receive DMA on SCIF and HSCIF, submit the receive DMA request
from the receive interrupt handler instead.
In some sense this is similar to the SCIFA/SCIFB behavior, where the
RDRQE (Rx Data Transfer Request Enable) bit is also set from the receive
interrupt handler.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The receive DMA workqueue function work_fn_rx() handles two things:
1. Reception of a full buffer on completion of a receive DMA request,
2. Reception of a partial buffer on receive DMA time-out.
The workqueue is kicked by both the receive DMA completion handler, and
by a timer to handle DMA time-out.
As there are always two receive DMA requests active, it's possible that
the receive DMA completion handler is called a second time before the
workqueue function runs.
As the time-out handler re-enables the receive interrupt, an interrupt
may come in before time-out has been fully handled.
Move part 1 into the receive DMA completion handler, and move part 2
into the receive DMA time-out handler, to fix these race conditions.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows to:
- Remove forward declarations of static functions,
- Coalesce two sections protected by #ifdef CONFIG_SERIAL_SH_SCI_DMA,
- Avoid shuffling functions around in the near future,
- Avoid adding forward declarations in the near future.
No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On receive DMA time-out, avoid calling sci_dma_rx_push() if no data was
transferred by the timed out DMA request.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_SERIAL_SH_SCI_DMA is enabled, the driver doesn't enable TIE
on SCIF or HSCIF. However, this driver may call sci_tx_interrupt()
in sci_er_interrupt(). After that, the driver cannot care of the
interrupt, and then "irq 109: nobody cared" happens on r8a7791/koelsch
board. This patch fixes the issue.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[geert] Keep kicking tx when using PIO
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error handler calls sci_rx_interrupt() to drain the receive FIFO if
an error condition happens.
However, if DMA is enabled on SCIFA or SCIFB, this will call
disable_irq_nosync() twice. Due to this imbalance, the receive interrupt
will never be re-enabled, and reception stops forever.
To fix this, restrict draining the FIFO to PIO mode, and just call
sci_receive_chars() directly.
Inspired by a patch from Yoshihiro Shimoda
<yoshihiro.shimoda.uh@renesas.com>.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue that this driver causes a NULL pointer
dereference in the following conditions:
- CONFIG_HIGHMEM and CONFIG_SERIAL_SH_SCI_DMA are enabled
- This driver runs on the sci_dma_rx_push()
This issue was caused by virt_to_page(buf) in the sci_request_dma()
because this driver didn't check if the "buf" was valid or not. So,
this patch uses the "buf" from dma_alloc_coherent() as is, not page.
This patch also fixes a WARNING issue in sci_rx_dma_release():
WARNING: CPU: 0 PID: 1328 at lib/dma-debug.c:1125 check_unmap+0x444/0x848()
rcar-dmac e6700000.dma-controller: DMA-API: device driver frees DMA memory with different CPU address [device address=0x000000006dd89000] [size=64 bytes] [cpu alloc address=0x000000016189c000] [cpu free address=0x0000000080000000]
WARNING: CPU: 1 PID: 1 at drivers/base/dma-mapping.c:334 dma_common_free_remap+0x48/0x6c()
trying to free invalid coherent area: (null)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[geert] Rebased
[geert] Reworded
[geert] Dropped .rx_chunk, as it's always identical to .rx_buf[0]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to keep all buffer and DMA pointers on the stack.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch from using tty_buffer_request_room() and looping over
tty_insert_flip_char() to tty_insert_flip_string().
Keep track of buffer overruns in the icount structure, like
serial_core.c does.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently sci_dma_rx_push() has to find the active scatterlist itself,
but in some cases the caller already knows.
Hence let the caller pass the scatterlist, and introduce a helper to
find the active DMA request while we're at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During serial port shutdown, the DMA receive worker function may still
be called after the receive DMA cleanup function has been called.
Fix this race condition between work_fn_rx() and sci_rx_dma_release() by
acquiring the port's spinlock in sci_rx_dma_release().
This requires releasing the spinlock in work_fn_rx() before calling (any
function that may call) sci_rx_dma_release().
Terminate all active receive DMA descriptors to release them, and to
make sure no more completions come in.
Do the same in sci_tx_dma_release() for symmetry, although the serial
upper layer will no longer submit more data at this point of time.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a problem when the sci_dma_rx_complete() is processed
before cancel process of work_fn_rx() completes by rx_timer_fn().
This patch locks work_fn_rx().
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resubmission of DMA descriptors is explicitly forbidden by the DMA
engine API.
Hence pass DMA_CTRL_ACK to dmaengine_prep_slave_sg(), and prepare a new
DMA descriptor instead of reusing the old one.
Remove sci_port.desc_rx[], as there's no longer a need to access the
active descriptor.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the error handling in sci_submit_rx() by
- Moving it to the end of the function,
- Just calling dmaengine_terminate_all() instead of calling
async_tx_ack() for all already submitted descriptors.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As dmaengine_prep_slave_sg() is called with the DMA_CTRL_ACK flag set
for DMA transmit requests, there's no need to explicitly acknowledge DMA
transmit requests in the DMA transmit completion callback.
Hence remove the call to async_tx_ack(), and remove the now unused
dma_async_tx_descriptor pointer in the sci_port structure.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the SCI driver from the SHDMAE-specific partial DMA transfer
handling to the generic dmaengine residual data framework.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace open-coded
- calls to dma_async_tx_descriptor.tx_submit() by calls to the
dmaengine_submit() helper,
- dma_cookie_t comparisons by calls to dma_submit_error().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mapped transmit buffer is never unmapped. This leaks quite some
mappings, as the mapping is done in uart_ops.startup(), i.e. every time
the device is opened. Unmap the buffer on device close.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the DMA transmit code by using dma_map_single() instead of
constantly modifying the single-entry scatterlist to match what's
currently being transmitted.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When comparing differently sized types, it's better to use
min_t()/max_t() than adding casts.
Also use "unsigned int" instead of "int", as that's the right type for
the length of an SG entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To function correctly in the presence of an IOMMU, the DMA buffers must
be managed using the DMA channel's device instead of the platform
device's device.
Make sure to free the DMA memory before releasing the channel, not
after.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let sci_request_dma() handle failures to initialize DMA itself.
This way sci_tx_dma_release() and sci_rx_dma_release() don't have to
consider partial initialization, and thus don't need to reset DMA
addresses to DMA_ERROR_CODE, which is not 100% portable access
architectures.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the life of the driver developer/debugger easier:
- Add __func__ prefix to identical messages,
- Add DMA directions to messages,
- Add TX failure messages,
- Always use "cookie %d" for DMA cookies,
- "#%d" is reserved for the DMA cookie/descriptor index.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix an issue that the driver may cause "nobody cared" IRQ
when this driver detects the overrun flag only.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8b6ff84c2d ("serial: sh-sci: Fix R-Car SCIF and HSCIF
overrun handling") added overrun handling for (H)SCIF using the SCLSR
register, but also accidentally added a bogus call to
sci_handle_fifo_overrun() in the receive interrupt path.
Remove it again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reorder sampling_rate assignment for consistency in all cases of the
switch statement.
Avoid using the ternary conditional operator to make it more clear that
the value is overridden by platform data.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial_core.c was moved from drivers/serial/ to drivers/tty/serial/ a
while ago. Remove the path to make it move-proof.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIF_ERROR_CLEAR includes SCIFA_ORER, which exists only on SCIFA/SCIFB
and SCIF on sh7705/sh7720/sh7721.
To fix this:
1. Remove SCIFA_ORER from the definition of SCIF_ERROR_CLEAR,
2. During initialization, store the error clear mask to use,
incorporating the overrun bit only if it applies to the SCxSR
register.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The #ifdef logic to clear SCxSR bits using RMW on SCIFA/SCIFB and SCIF
variants with some SCIFA features (sh7705/SH7720/sh7721) has several
drawbacks:
- It wasn't updated for newer R-Mobile variants (APE6),
- It doesn't correctly handle SoCs with both SCIF and SCIFA/B (e.g.
R-Car Gen2, but also legacy sh7723/sh7724),
- It doesn't play well with ARM multi-platform kernels: on R-Car Gen2,
SCIF/SCIFA/SCIFB/HSCIF were handled differently, depending on
whether r8a7740 or sh73a0 support was enabled or not,
Replace the #ifdef logic by runtime logic to fix this.
SCIFA/SCIFB and SCIF on sh7705/sh7720/sh7721 use RMW to clear error
bits, other variants use plain stores, as before.
Note that this changes behavior for SCIFA on sh7723/sh7724 (these SoCs
have both SCIF and SCIFA), which didn't use RMW before.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the tty and serial driver patches for 4.2-rc1.
A number of individual driver updates, some code cleanups, and other
minor things, full details in the shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNoSAACgkQMUfUDdst+ymxNQCguSEmkAYNDdLyYhdcOqSxJt9u
U1gAoMThUDoomkx6CTDMU1wn53hxgMk9
=eCUS
-----END PGP SIGNATURE-----
Merge tag 'tty-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the tty and serial driver patches for 4.2-rc1.
A number of individual driver updates, some code cleanups, and other
minor things, full details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'tty-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (152 commits)
Doc: serial-rs485.txt: update RS485 driver interface
Doc: tty.txt: remove mention of the BKL
MAINTAINERS: tty: add serial docs directory
serial: sprd: check for NULL after calling devm_clk_get
serial: 8250_pci: Correct uartclk for xr17v35x expansion chips
serial: 8250_pci: Add support for 12 port Exar boards
serial: 8250_uniphier: add bindings document for UniPhier UART
serial: core: cleanup in uart_get_baud_rate()
serial: stm32-usart: Add STM32 USART Driver
tty/serial: kill off set_irq_flags usage
tty: move linux/gsmmux.h to uapi
doc: dt: add documentation for nxp,lpc1850-uart
serial: 8250: add LPC18xx/43xx UART driver
serial: 8250_uniphier: add UniPhier serial driver
serial: 8250_dw: support ACPI platforms with integrated DMA engine
serial: of_serial: check the return value of clk_prepare_enable()
serial: of_serial: use devm_clk_get() instead of clk_get()
serial: earlycon: Add support for big-endian MMIO accesses
serial: sirf: use hrtimer for data rx
serial: sirf: correct the fifo empty_bit
...
There is much SCI of SoC having within,
and the register size is also different in everyone.
So get from platform device.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Acked-by: by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The code it refers to was removed in commit b545e4f406 ("serial:
sh-sci: Compute overrun_bit without using baud rate algo").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
error_mask is the union of all error indicating bits in the SCxSR
register, while overrun_mask may apply to a different register (SCLSR),
depending on the SCI variant.
Hence overrun_mask should only be ORed into error_mask if it applies to
the SCxSR register.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The various SCI implementations use 3 different methods to signal
overrun errors:
- Bit SCI_ORER in register SCxSR on SCI,
- Bit SCIFA_ORER in register SCxSR on SCIFA and SCIFB, and SCIF on
SH7705/SH7720/SH7721,
- Bit SCLSR_ORER in (optional!) register SCLSR on (H)SCIF.
However:
1. sci_handle_fifo_overrun()
a. handles (H)SCIF and SCIFA/SCIFB only,
b. treats SCIF on SH7705/SH7720/SH7721 incorrectly,
2. sci_mpxed_interrupt()
a. treats SCIF on SH7705/SH7720/SH7721 incorrectly,
b. ignores that not all SCIFs have the SCLSR register, causing
"Invalid register access" WARN()ings.
To fix the above:
1. Determine and store the correct register enum during
initialization,
2. Replace the duplicated buggy switch statements by using the stored
register enum,
3. Add the missing existence check to sci_mpxed_interrupt().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing overrun bit definition for (H)SCIF.
Replace overrun_bit by overrun_mask, so we can use the existing
defines instead of hardcoded values.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the register definitions for the Serial Port Control and Data
Registers on SCIFA/SCIFB, which are needed for RTS/CTS pin control.
Extracted from patches by Magnus Damm <damm+renesas@opensource.se>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current calculation method in the case of 9600bps, rounding error occurs
has become setting that occur timeout faster than the required time. When we
use 9600bps, 32byte buffer, 10 bit (CS8) and 100 HZ, it becomes 3 jiffies
(30msec). In fact it is necessary 33msec. This updates to the calculation
that are not actually less than the value set by the rounding error.
Also, this is nothing will be calculated value when there is no load. If there
are a lot of case load, overrun error will occur immediately.
This is by the buffer size to be calculated twice the DMA buffer, and add the
change of setting a sufficient time-out value.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIFA and SCIFB can detect the overrun, but it does not support.
This adds overrun handling of SCIFA and SCIFB.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the driver cannot return from overrun error if characters
are output during overrun process, use dev_dbg() instead of
dev_notice() to log the error message of overrun in syslog.
Based on a patch by Hisashi Nakamura.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to make it possible to restore from hibernation not only in Linux but
also in e.g. U-Boot, we have to use sci_{suspend|remove}() for the PM {freeze|
thaw|restore}() methods. It's handy to achieve this by using SIMPLE_DEV_PM_OPS()
macro, however we have to annotate sci_{suspend|remove}() with '__maybe_unused'
in order to avoid compilation warnings when CONFIG_PM_SLEEP is undefined.
Based on orignal patch by Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
This changes negative values of error rate to be checked, because these
values are valid as error rate. And this changes in the process of adopting
a value close to 0.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When the error of the same bit rate is detected, we will need to select
the recive margin is large. Current code holds the minimum error, it does
not have to check the recive margin. This adds this calculation.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If bit-rate calculation result of HSCIF is expect 255 from 0,
driver does not calculate error bit. However, we need to round
the value to calculate error bit in the case of negative value.
This rounds the value of bit-rate using clamp(), and bit-rate is the
case of negative value, it enables the calculation of the error bit.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the decimal point is discarded calculation of BRR.
Therefore, it can not calculate a value close to the correct value.
This patch fixes this problem by using DIV_ROUND_CLOSEST.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big tty/serial driver update for 3.15-rc1.
Nothing major, a number of serial driver updates and a few tty core
fixes as well.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7CWAACgkQMUfUDdst+ylDXACg0vZ+J+5OXbbE3lywVCAebjhB
XzkAn1lz7JRIils7IlckAJ2w/m50b174
=M+8c
-----END PGP SIGNATURE-----
Merge tag 'tty-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver update from Greg KH:
"Here's the big tty/serial driver update for 3.15-rc1.
Nothing major, a number of serial driver updates and a few tty core
fixes as well.
All have been in linux-next for a while"
* tag 'tty-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (71 commits)
tty/serial: omap: empty the RX FIFO at the end of half-duplex TX
tty/serial: omap: fix RX interrupt enable/disable in half-duplex TX
serial: sh-sci: Neaten dev_<level> uses
serial: sh-sci: Replace hardcoded 3 by UART_PM_STATE_OFF
serial: sh-sci: Add more register documentation
serial: sh-sci: Remove useless casts
serial: sh-sci: Replace printk() by pr_*()
serial_core: Avoid NULL pointer dereference in uart_close()
serial_core: Get a reference for port->tty in uart_remove_one_port()
serial: clps711x: Give a chance to perform useful tasks during wait loop
serial_core: Grammar s/ports/port's/
serial_core: Spelling s/contro/control/
serial: efm32: properly namespace location property
serial: max310x: Add missing #include <linux/uaccess.h>
synclink: fix info leak in ioctl
serial: 8250: Clean up the locking for -rt
serial: 8250_pci: change BayTrail default uartclk
serial: 8250_pci: more BayTrail error-free bauds
serial: sh-sci: Add missing call to uart_remove_one_port() in failure path
serial_core: Unregister console in uart_remove_one_port()
...
Two cpufreq notifiers CPUFREQ_RESUMECHANGE and CPUFREQ_SUSPENDCHANGE have
not been used for some time, so remove them to clean up code a bit.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make banner const while we're at it
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If cpufreq_register_notifier() fails, we have to remove the port added by
sci_probe_single(), which is not done by sci_cleanup_single().
Else the serial port stays active from the point of view of the serial
subsystem, and it may crash when userspace getty is started, or when the
loadable driver module is unloaded.
This was introduced by commit 6dae14216c
("serial: sh-sci: Fix probe error paths").
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following compile warning about cast to pointer from
integer of different size.
drivers/tty/serial/sh-sci.c:2021:19: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend the driver to with support for SCIx device tree bindings. A
minimal set of features is supported, additional properties can be added
later should the need to describe more device features arise.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The fields are not used anymore by board files, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The field isn't set by any board, remote it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Computing the baud rate register value requires knowledge of the
hardware sampling rate. This information is currently encoded in a baud
rate calculation algorithm ID passed through platform data. However, it
can be derived from the port type directly in most cases.
Compute the sampling rate internally in the driver if the baud rate
calculation algorithm ID isn't specified, and allow platforms to
override the sampling rate through platform data in special cases (this
is only required for SCIFA ports on sh7723 and sh7724, the reason needs
to be investigated).
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The overrun bit index is a property of the hardware. It's currently
computed based on a different and unrelated hardware property, the baud
rate calculation algorithm. Compute it using hardware identification
information only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The driver requests at initialization time GPIOs passed through platform
data. No platform makes use of this feature, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
None of the fields is ever set by board code, and both of them are set
in the driver at probe time. Move them out of struct plat_sci_port to
struct sci_port.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Memory and IRQ resources are currently passed to the driver through
platform data. Support passing them through the standard platform
resources mechanism instead. This deprecates platform data resources.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The IRQ number can't be modified by the user as the port is fixed.
There's no need to check the new IRQ number as it will be ignored by the
core.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The base address, IRQ and baud rate generator parent clock rate can't be
changed by userspace. Mark the port as fixed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The driver checks if the interrupt number is greater than nr_irqs and
returns an error in that case. The same check is already performed by
the caller, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Rewrite the baud rate register value calculations in easier to read
forms. The computed value isn't modified.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and
clk_disable_unprepare() to get ready for the migration to the common
clock framework.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The break timer accesses hardware registers and thus requires the port
to be enabled. It currently ensures this by enabling the port at the
beginning of the timer handler, and disabling it at the end. However,
the enable/disable operations call the runtime PM sync functions, which
are not allowed in atomic context. The current situation is thus broken.
This change relies on non-atomic code to enable/disable the port. The
break timer will only be started from the IRQ handler, which already
runs with the port enabled. We just need to ensure that the port won't
be disabled with the timer running, and that's easily done by just
cancelling the timer in the port disable function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the %zu and %pad printk specifiers to print size_t and dma_addr_t
variables, and cast pointers to uintptr_t instead of unsigned int where
applicable. This fixes warnings on platforms where pointers and/or
dma_addr_t have a different size than int.
Cc: linux-serial@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change addresses two warnings that are flagged by gcc relating to
potential access to the ssr and cks variables while they are uninitialised.
I have addressed this by initialising the values to
the defaults present in sci_baud_calc_hscif().
It is my analysis that cks is always initialised if used
but that without this change ssr may be accessed while uninitialised.
The code altered by this patch was introduced by commit
f303b364b4 ("serial: sh-sci: HSCIF support").
Reported-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds support for "High Speed Serial Communications Interface with FIFO",
essentially a SCIF with 128-byte FIFOs and more accurate baud rate
generator.
Signed-off-by: Ulrich Hecht <ulrich.hecht@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_char is the next one to proceed. This one is used all
over the code, so the patch is huge.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty pointer in
many call sites. Only tty_port will be needed and hence no more
tty_port_tty_get calls in those paths.
Here we start with tty_buffer_request_room.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the previous commit, console write function (serial_console_write)
is changed to disable SCI interrupts while printing console strings.
This introduces possible race cases in the serial startup / shutdown
functions on SMP systems.
This patch fixes the sh-sci in the same way as commit 9ec1882df2
(tty: serial: imx: console write routing is unsafe on SMP, from
Xinyu Chen <xinyu.chen@freescale.com>, 2012-08-27) did.
There could be several consumers of the console,
* the kernel printk
* the init process using /dev/kmsg to call printk to show log
* shell, which opens /dev/console and writes with sys_write()
The shell goes into the normal UART open() and write() system calls,
while the other two go into the console operations. The open() call
invokes serial startup function (sci_startup), which will write to
the SCSCR register (to enable or disable SCI interrupts) without any
locking. This will conflict with the console serial function.
Add spinlock protections in sci_startup() and sci_shutdown() properly.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Symptom:
When entering the suspend with Android logcat running, printk() call
gets stuck and never returns. The issue can be observed at printk()s
on nonboot CPUs when going to offline with their interrupts disabled,
and never seen at boot CPU (core0 in our case).
Details:
serial_console_write() lacks of appropriate spinlock handling.
In SMP systems, as long as sci_transmit_chars() is being processed
at one CPU core, serial_console_write() can stuck at the other CPU
core(s), when it tries to access to the same serial port _without_
a proper locking. serial_console_write() waits for the transmit FIFO
getting empty, while sci_transmit_chars() writes data to the FIFO.
In general, peripheral interrupts are routed to boot CPU (core0) by
Linux ARM standard affinity settings. SCI(F) interrupts are handled
by core0, so sci_transmit_chars() is processed on core0 as well.
When logcat is running, it writes enormous log data to the kernel at
every moment, forever. So core0 can repeatedly continue to process
sci_transmit_chars() in its interrupt handler, which eventually makes
the other CPU core(s) stuck at serial_console_write().
Looking at serial/8250.c, this is a known console write lockup issue
with SMP kernels. Fix the sh-sci driver in the same way 8250.c does.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
About FIFO count, there are two variants of SCIFs which show
a) TX count in upper, RX count in lower byte of FDR register
b) TX count in TFDR register, RX count in RFDR register
Common SCIFB regmap in current source code is defined as "a".
At least 7372 and 73a0 HW manual say their SICFB are "b".
This patch alters the definition to "b", considering the current
one has come from a mistake. The reason is as follows.
The flag SCIFB sh-sci driver means it has 256 byte FIFO.
The count is from 0(empty) to 256(full), that makes 9-bit.
Because FDR is 16-bit register, it can not hold two 9-bits.
That's why, SCIFB can not be "a".
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current mask 0xff to SCTFDR/RFDR damages SCIFB, because the
registers on SCIFB have 9-bit data (0 to 256).
This patch changes the mask according to port->fifosize.
Though I'm not sure if the mask is really needed (I don't know if
there are variants which have non-zero upper bits), it is safer.
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support prescaler 1/16 and 1/64, in addition to current 1 and 1/4.
Supporting below 2400bps was dropped long time ago in mainline.
Since then, setting lower rate has been resulting in erroneous
register value, without indicating any errors through API.
This patch adds more prescaler to support lower rates again.
This still doesn't check range, but we won't hit the case because
even 50bps at 48MHz clock is now supported.
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 1ba7622094 (serial: sh-sci: console Runtime PM support,
from Magnus Damm <damm@opensource.se>, 2011-08-03), tried to support
console runtime PM, but unfortunately it didn't work for us for some
reason. We did not investigated further at that time, instead would
like to propose a different approach.
In Linux tty/serial world, to get console PM work properly, a serial
client driver does not have to maintain .runtime_suspend()/..resume()
calls itself, but can leave console power power management handling to
the serial core driver.
This patch moves the sh-sci driver in that direction.
Notes:
* There is room to optimize console runtime PM more aggressively by
maintaining additional local runtime PM calls, but as a first step
having .pm() operation would suffice.
* We still have a couple of direct calls to sci_port_enable/..disable
left in the driver. We have to live with them, because they're out
of serial core's help.
Signed-off-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This partially reverts commit 1ba7622094 (serial: sh-sci: console
Runtime PM support, from Magnus Damm <damm@opensource.se>, 2011-08-03).
The generic 'serial_core' can take care of console PM maintenance,
so all (or at least the first thing) we have to do to get console PM
work properly, is to implement uart_ops ->pm() operation in the sh-sci
serial client driver.
This patch partially reverts the commit above, but leaving sci_reset()
change in place, because sci_reset() is already part of another commit
(73c3d53f38 serial: sh-sci: Avoid FIFO clear for MCE toggle.).
A revised version of console PM support follows next.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 5a50a01bf0 (sh-sci / PM: Use power.irq_safe, from
Rafael J. Wysocki <rjw@sisk.pl>, 2011-08-24).
In order to get console PM work properly, we should implement uart_ops
->pm() operation, rather than sprinkle band-ading runtime PM calls in
the driver.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 048be431e4 (sh-sci / PM: Avoid deadlocking runtime
PM, from Rafael J. Wysocki <rjw@sisk.pl>, 2012-03-09).
In order to get console PM work properly, we should implement uart_ops
->pm() operation, rather than sprinkle band-ading runtime PM calls in
the driver.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was already pointed out how to fix these cases before the offending
patches were merged, but unsurprisingly, that didn't happen. As this
change is entirely superfluous to begin with, simply shut things up by
casting everything away.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
A recent commit:
commit d6fa5a4e7a
Author: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
serial: sh-sci: prepare for conversion to the shdma base library
is not sufficient to update the sh-sci driver to the new shdma driver
layout. This caused compilation breakage, when CONFIG_SERIAL_SH_SCI_DMA
is enabled. This patch trivially fixes the problem by updating the DMA
descriptor manipulation code.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Pull slave-dmaengine update from Vinod Koul:
"This time we have a new dmaengine driver from the tegra folks. Also
we have Guennadi's cleanup of sh drivers which incudes a library for
sh drivers. And the usual odd fixes in bunch of drivers and some nice
cleanup of dw_dmac from Andy."
Fix up conflicts in drivers/mmc/host/sh_mmcif.c
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (46 commits)
dmaengine: Cleanup logging messages
mmc: sh_mmcif: switch to the new DMA channel allocation and configuration
dma: sh: provide a migration path for slave drivers to stop using .private
dma: sh: use an integer slave ID to improve API compatibility
dmaengine: shdma: prepare to stop using struct dma_chan::private
sh: remove unused DMA device pointer from SIU platform data
ASoC: siu: don't use DMA device for channel filtering
dmaengine: shdma: (cosmetic) simplify a static function
dmaengine: at_hdmac: add a few const qualifiers
dw_dmac: use 'u32' for LLI structure members, not dma_addr_t
dw_dmac: mark dwc_dump_lli inline
dma: mxs-dma: Export missing symbols from mxs-dma.c
dma: shdma: convert to the shdma base library
ASoC: fsi: prepare for conversion to the shdma base library
usb: renesas_usbhs: prepare for conversion to the shdma base library
ASoC: siu: prepare for conversion to the shdma base library
serial: sh-sci: prepare for conversion to the shdma base library
mmc: sh_mobile_sdhi: prepare for conversion to the shdma base library
mmc: sh_mmcif: remove unneeded struct sh_mmcif_dma, prepare to shdma conversion
dma: shdma: prepare for conversion to the shdma base library
...
The driver supports a maximum number of ports configurable at compile
time. Make sure the probe() method fails when registering a port that
exceeds the maximum instead of returning success without registering the
port.
This fixes a crash at system suspend time, when the driver tried to
suspend a non-registered port using the UART core.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Geert Uytterhoeven