Commit a99c47a2 "intel-iommu: errors with smaller iommu widths" replace the
dmar_domain->pgd with the first entry of page table when iommu's supported
width is smaller than dmar_domain's. But it use physical address directly
for new dmar_domain->pgd...
This result in KVM oops with VT-d on some machines.
Reported-by: Allen Kay <allen.m.kay@intel.com>
Cc: Tom Lyon <pugs@cisco.com>
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: clear bridge resource range if BIOS assigned bad one
PCI: hotplug/cpqphp, fix NULL dereference
Revert "PCI: create function symlinks in /sys/bus/pci/slots/N/"
PCI: change resource collision messages from KERN_ERR to KERN_INFO
There are devices out there which are PCI Hot-plug controllers with
compaq PCI IDs, but are not bridges, hence have pdev->subordinate
NULL. But cpqphp expects the pointer to be non-NULL.
Add a check to the probe function to avoid oopses like:
BUG: unable to handle kernel NULL pointer dereference at 00000050
IP: [<f82e3c41>] cpqhpc_probe+0x951/0x1120 [cpqphp]
*pdpt = 0000000033779001 *pde = 0000000000000000
...
The device here was:
00:0b.0 PCI Hot-plug controller [0804]: Compaq Computer Corporation PCI Hotplug Controller [0e11:a0f7] (rev 11)
Subsystem: Compaq Computer Corporation Device [0e11:a2f8]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This reverts commit 75568f8094.
Since they're just a convenience anyway, remove these symlinks since
they're causing duplicate filename errors in the wild.
Acked-by: Alex Chiang <achiang@canonical.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We can often deal with PCI resource issues by moving devices around. In
that case, there's no point in alarming the user with messages like these.
There are many bug reports where the message itself is the only problem,
e.g., https://bugs.launchpad.net/ubuntu/+source/linux/+bug/413419 .
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
JMB362 is a new variant of jmicron controller which is similar to
JMB360 but has two SATA ports instead of one. As there is no PATA
port, single function AHCI mode can be used as in JMB360. Add pci
quirk for JMB362.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Aries Lee <arieslee@jmicron.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.infradead.org/iommu-2.6:
intel-iommu: Set a more specific taint flag for invalid BIOS DMAR tables
intel-iommu: Combine the BIOS DMAR table warning messages
panic: Add taint flag TAINT_FIRMWARE_WORKAROUND ('I')
panic: Allow warnings to set different taint flags
intel-iommu: intel_iommu_map_range failed at very end of address space
intel-iommu: errors with smaller iommu widths
intel-iommu: Fix boot inside 64bit virtualbox with io-apic disabled
intel-iommu: use physfn to search drhd for VF
intel-iommu: Print out iommu seq_id
intel-iommu: Don't complain that ACPI_DMAR_SCOPE_TYPE_IOAPIC is not supported
intel-iommu: Avoid global flushes with caching mode.
intel-iommu: Use correct domain ID when caching mode is enabled
intel-iommu mistakenly uses offset_pfn when caching mode is enabled
intel-iommu: use for_each_set_bit()
intel-iommu: Fix section mismatch dmar_ir_support() uses dmar_tbl.
Removed check to prevent hotplug of display devices within pciehp.
Originally this was thought to have been required within the PCI
Hotplug specification for some legacy devices. However there is
no such requirement in the most recent revision. The check prevents
hotplug of not only display devices but also computational GPUs
which require serviceability.
Signed-off-by: Praveen Kalamegham <praveen@nextio.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
At the moment only PCI-E briges can be flagged as hotplug, thus
allowing manual resource preallocation via pci=hpmemsize=nnM and
pci=hpiosize=nnM kernel parameters. Some PCI hotplug bridges, e.g.
PLX 6254 can also benefit from this functionalily, as kernel fails
to properly allocate their resources when hotplug device is added
and PCI bus is rescanned.
This patch adds header quirk for PLX 6254 that marks this bridge
as hotplug. Other PCI bridges with similar problems can use it
as well.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCI config space bin_attr read handler has a hardcoded CAP_SYS_ADMIN
check to verify privileges before allowing a user to read device
dependent config space. This is meant to protect from an unprivileged
user potentially locking up the box.
When assigning a PCI device directly to a guest with libvirt and KVM,
the sysfs config space file is chown'd to the unprivileged user that
the KVM guest will run as. The guest needs to have full access to the
device's config space since it's responsible for driving the device.
However, despite being the owner of the sysfs file, the CAP_SYS_ADMIN
check will not allow read access beyond the config header.
With this patch we check privileges against the capabilities used when
openining the sysfs file. The allows a privileged process to open the
file and hand it to an unprivileged process, and the unprivileged process
can still read all of the config space.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
Now, a dedicated HEST tabling parsing code is used for PCIE AER
firmware_first setup. It is rebased on general HEST tabling parsing
code of APEI. The firmware_first setup code is moved from PCI core to
AER driver too, because it is only AER related.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Len Brown <len.brown@intel.com>
We now know how to deal with these tables so that they are harmless.
Set TAINT_FIRMWARE_WORKAROUND instead of the default TAINT_WARN.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We have nearly the same code for warnings repeated four times. Move
it into a separate function.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_read/write_vpd() can fail due to a timeout. Usually the command
times out because of firmware issues (incorrect vpd length, etc.) on the
PCI card. Currently, the timeout occurs silently.
Output a message to the user indicating that they should check with
their vendor for new firmware.
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This fixes all occurrences of pci_enable_device and pci_disable_device
in all comments. There are no code changes involved.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As reported in <http://bugs.debian.org/552299>, MSI appears to be
broken for this on-board device. We already have a quirk for the
P5N32-SLI Premium; extend it to cover both variants of the board.
Reported-by: Romain DEGEZ <romain.degez@smartjog.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/amd-iommu: Add amd_iommu=off command line option
iommu-api: Remove iommu_{un}map_range functions
x86/amd-iommu: Implement ->{un}map callbacks for iommu-api
x86/amd-iommu: Make amd_iommu_iova_to_phys aware of multiple page sizes
x86/amd-iommu: Make iommu_unmap_page and fetch_pte aware of page sizes
x86/amd-iommu: Make iommu_map_page and alloc_pte aware of page sizes
kvm: Change kvm_iommu_map_pages to map large pages
VT-d: Change {un}map_range functions to implement {un}map interface
iommu-api: Add ->{un}map callbacks to iommu_ops
iommu-api: Add iommu_map and iommu_unmap functions
iommu-api: Rename ->{un}map function pointers to ->{un}map_range
intel_iommu_map_range() doesn't allow allocation at the very end of the
address space; that code has been simplified and corrected.
Signed-off-by: Tom Lyon <pugs@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When using iommu_domain_alloc with the Intel iommu, the domain address
width is always initialized to 48 bits (agaw 2). This domain->agaw value
is then used by pfn_to_dma_pte to (always) build a 4 level page table.
However, not all systems support iommu width of 48 or 4 level page tables.
In particular, the Core i5-660 and i5-670 support an address width of 36
bits (not 39!), an agaw of only 1, and only 3 level page tables.
This version of the patch simply lops off extra levels of the page tables
if the agaw value of the iommu is less than what is currently allocated
for the domain (in intel_iommu_attach_device). If there were already
allocated addresses above what the new iommu can handle, EFAULT is
returned.
Signed-off-by: Tom Lyon <pugs@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This reverts commit 977d17bb17, because it
can cause problems with some devices not getting any resources at all
when the resource tree is re-allocated.
For an example of this, see
https://bugzilla.kernel.org/show_bug.cgi?id=15960
(originally https://bugtrack.alsa-project.org/alsa-bug/view.php?id=4982)
(lkml thread: http://lkml.org/lkml/2010/4/19/20)
where Peter Henriksson reported his Xonar DX sound card gone, because
the IO port region was no longer allocated.
Reported-bisected-and-tested-by: Peter Henriksson <peter.henriksson@gmail.com>
Requested-by: Andrew Morton <akpm@linux-foundation.org>
Requested-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Skip zero-ing in aer_alloc_rpc() since it is allocated by kzalloc().
The closing comment marker "*/" is recommended for kernel-doc comments.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
I noticed that when I inject a fatal error to an endpoint via
aer-inject, aer_root_reset() is called as reset_link for a
downstream port at upstream of the endpoint:
pcieport 0000:00:06.0: AER: Uncorrected (Fatal) error received: id=5401
:
pcieport 0000:52:02.0: Root Port link has been reset
It externally appears to be working, but internally issues some
accesses to PCI_ERR_ROOT_COMMAND/STATUS registers that is for
root port so not available on downstream port.
This patch introduces default_downstream_reset_link that is
a version of aer_root_reset() with no accesses to root port's
register. It is used for downstream ports that has no reset_link
function its specific.
This patch also updates related description in pcieaer-howto.txt.
Some minor fixes are included.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The pcie->port of port service device points the port associated
the service with. The find_aer_service iterates over children of
given port udev.
So it is clear that the pcie->port of port service of given port
udev must always point the udev.
Therefore we can know the type of udev without checking its children.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Make it clear that we only interest in 2 *_RCV bits.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current get_e_source() returns pointer to an element of array.
However since it also progress consume counter, it is possible
that the element is overwritten by newly produced data before
the element is really consumed.
This patch changes get_e_source() to copy contents of the element
to address pointed by its caller. Once copied the element in
array can be consumed.
And relocate this function to more innocuous place.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Divide tricky for-loop into readable if-blocks.
The logic to set multi_error_valid (to force walking pci bus
hierarchy to find 2nd~ error devices) is changed too, to check
MULTI_{,_UN}COR_RCV bit individually and to force walk only when
it is required.
And rework setting e_info->severity for uncorrectable, not to use
magic numbers.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Stop iteration if we cannot register any more.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Take core part of find_device_iter() to make a new function
is_error_source() that checks given device has report an error
or not.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Return bool to indicate that the source device is found or not.
This allows us to skip calling aer_process_err_devices() if we can.
And move dev_printk for debug into this function.
v2: return bool instead of int
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These functions are only called from init/remove path of aerdrv,
so move them from aerdrv_core.c to aerdrv.c, to make them static.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This cleanup solves some minor naming issues by removing unuseful
function aer_delete_rootport() and by renaming disable_root_aer()
to aer_disable_rootport().
- Inconsistent location of alloc & free:
The struct rpc is allocated in aer_alloc_rpc() at aerdrv.c
while it is implicitly freed in aer_delete_rootport() at
aerdrv_core.c.
- Inconsistent function name:
It makes a bit confusion that aer_delete_rootport() is seemed
to be paired with aer_enable_rootport(), i.e. there is neither
"add" against "delete" nor "disable" against "enable".
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
A successful write() to the "reset" sysfs attribute should return the
number of bytes written, not 0. Otherwise userspace (bash) retries the
write over and over again.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Most current machines have no problem with this, and in fact many devices and
features work best (or only!) with MSI.
Reported-by: Petteri Räty <betelgeuse@gentoo.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_lock must be a real spinlock in preempt-rt. Convert it to
raw_spinlock. No change for !RT kernels.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch (as1353) removes a couple of unnecessary assignments from
the PCI core. The should_wakeup flag is naturally initialized to 0;
there's no need to clear it.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Create convenience symlinks in sysfs, linking slots to device
functions, and vice versa. These links make it easier for users to
figure out which devices actually live in what slots.
For example:
sapphire:/sys/bus/pci/slots # ls
1 10 2 3 4 5 6 7 8 9
sapphire:/sys/bus/pci/slots # ls -l 3
total 0
-r--r--r-- 1 root root 65536 Aug 18 14:10 address
lrwxrwxrwx 1 root root 0 Aug 18 14:10 function0 ->
../../../../devices/pci0000:23/0000:23:01.0
lrwxrwxrwx 1 root root 0 Aug 18 14:10 function1 ->
../../../../devices/pci0000:23/0000:23:01.1
sapphire:/sys/bus/pci/slots # ls -l 3/function0/slot
lrwxrwxrwx 1 root root 0 Aug 18 14:13 3/function0/slot ->
../../../bus/pci/slots/3
The original form of this patch was written by Matthew Wilcox,
and was enhanced to include links from the sysfs slots/ directory
pointing back at the device functions.
Cc: willy@linux.intel.com
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This ensures that the translations for unmapped IO mappings or
unmapped memory are properly removed from the MMU hash table
before such an unplug. Without this, the hypervisor refuses the
unplug operations due to those resources still being mapped by
the partition.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If the firmware puts a device back into D0 state at resume time, we'll
update its state in resume_noirq and thus skip the platform resume code.
Calling that code twice should be safe and we ought to avoid getting to
that point anyway, so remove the check and also allow the platform pci
code to be called for D0.
Fixes USB not being powered after resume on recent Lenovo machines.
Acked-by: Alex Chiang <achiang@canonical.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This reverts c519a5a7da. That change added a warning about devices that
didn't respond correctly when sizing BARs, which helped diagnose broken
devices. But the test wasn't specific enough, so it also complained about
working devices with zero-size BARs, e.g.,
https://bugzilla.kernel.org/show_bug.cgi?id=15822
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 074835f014 ("intel-iommu: Fix
kernel hand if interrupt remapping disabled in BIOS") is adding a check
for interrupt remapping disabled and is dereferencing the dmar_tbl
pointer without checking its value.
Unfortunately, this value is null when booting inside a 64bit virtual
box guest with io-apic disabled, leading to a crash. With a check on it,
the guest is now booting. It's triggering a WARN() in
clockevent_delta2ns but it's better than not booting at all and allows
the user to see there's something wrong on their io-apic setup.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When virtfn is used, we should use physfn to find correct drhd
-v2: add pci_physfn() Suggested by Roland Dreier <rdreier@cisco.com>
do can remove ifdef in dmar.c
-v3: Chris pointed out we need that for dma_find_matched_atsr_unit too
also change dmar_pci_device_match() static
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Roland Dreier <rdreier@cisco.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
While it may be efficient on real hardware, emulation of global
invalidations is very expensive as all shadow entries must be examined.
This patch changes the behaviour when caching mode is enabled (which is
the case when IOMMU emulation takes place). In this case, page specific
invalidation is used instead.
Signed-off-by: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In caching-mode mappings of pages (changes from non-present to present)
require invalidation.
Currently, this IOTLB flush is performed with domain ID of zero.
This is not according to the VT-d spec and causes big problems for
emulating software.
This patch uses the correct domain ID in IOTLB flushes.
Device IOTLB invalidation is performed only on present to non-present
changes. This decision is now based on explicit parameter instead of
zero domain-ID.
Signed-off-by: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
intel_map_sg used offset_pfn which was set to zero when invalidating the IOTLB.
intel_map_sg now uses size variable for this matter.
Signed-off-by: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Replace open-coded loop with for_each_set_bit().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
While testing completion timeouts I found that hardware was not recovering.
It looks like the hot reset was never being propagated to the endpoint
devices on the bus due to the fact that we were clearing the bit too
quickly.
The documentation I have states that we should be transmitting hot reset
TS1s for 2ms. To achieve this I have added a 2ms delay from the time we
set the secondary bus reset bit to the time we clear it. In addition I
changed the define used for the secondary bus reset bit to match the
register define that was being used.
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The missing initialization of the nb_cntl.strap_msi_enable does not
seem to be the only problem that prevents MSI, so that quirk is not
sufficient to enable MSI on all machines. To be safe, disable MSI
unconditionally for the internal graphics and HDMI audio on these
chipsets.
[rjw: Added the PCI_VENDOR_ID_AI quirk.]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/PCI: truncate _CRS windows with _LEN > _MAX - _MIN + 1
x86/PCI: for host bridge address space collisions, show conflicting resource
frv/PCI: remove redundant warnings
x86/PCI: remove redundant warnings
PCI: don't say we claimed a resource if we failed
PCI quirk: Disable MSI on VIA K8T890 systems
PCI quirk: RS780/RS880: work around missing MSI initialization
PCI quirk: only apply CX700 PCI bus parking quirk if external VT6212L is present
PCI: complain about devices that seem to be broken
PCI: print resources consistently with %pR
PCI: make disabled window printk style match the enabled ones
PCI: break out primary/secondary/subordinate for readability
PCI: for address space collisions, show conflicting resource
resources: add interfaces that return conflict information
PCI: cleanup error return for pcix get and set mmrbc functions
PCI: fix access of PCI_X_CMD by pcix get and set mmrbc functions
PCI: kill off pci_register_set_vga_state() symbol export.
PCI: fix return value from pcix_get_max_mmrbc()
pci_claim_resource() can fail, so pay attention and only claim success
when it actually succeeded. If pci_claim_resource() fails, it prints a
useful diagnostic.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bugzilla 15287 indicates that there's a problem with Message Signalled
Interrupts on VIA K8T890 systems. Add a quirk to disable MSI on these
systems.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Tested-by: Jan Kreuzer <kontrollator@gmx.de>
Tested-by: lh <jarryson@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
AMD says in section 2.5.4 (GFX MSI Enable) of #43291 (AMD 780G Family
Register Programming Requirements):
The SBIOS must enable internal graphics MSI capability in GCCFG by
setting the following: NBCFG.NB_CNTL.STRAP_MSI_ENABLE='1'
Quite a few BIOS writers misinterpret this sentence and think that
enabling MSI is an optional feature. However, clearing that bit just
prevents delivery of MSI messages but does not remove the MSI PCI
capabilities registers, and so leaves these devices unusable for any
driver that attempts to use MSI.
Setting that bit is not possible after the BIOS has locked down the
configuration registers, so we have to manually disable MSI for the
affected devices.
This fixes the codec communication errors in the HDA driver when
accessing the HDMI audio device, and allows us to get rid of the
overcautious quirk in radeon_irq_kms.c.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Alex Deucher <alexdeucher@gamil.com>
Cc: <stable@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Apply the CX700 quirk only when an external VT6212L is present (which
is the case for the errant hardware the quirk was written for), don't
touch the settings otherwise -- Hauppage PVR-500 tuners need PCI Bus
Parking in order to work and when that's turned on everything seems
to behave fine.
I guess the underlying problem is a combination of an external VT6212L
and the CX700 rather than the CX700's PCI being broken completely for
all cases...
Reported-by: Jeroen Roos <jeroen@roosnl.com>
Signed-off-by: Tim Yamin <plasm@roo.me.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If we can tell that a device isn't working correctly, we should tell
the user to make debugging easier. Otherwise, it can take a lot of
work to determine whether the problem is in the driver, PCMCIA, PCI,
hardware, etc., as in http://bugzilla.kernel.org/show_bug.cgi?id=12006
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change; just print resources in the conventional style.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change; this just tweaks the changes from 349e1823a405
so the new printks for disabled PCI-to-PCI bridge windows match the
ones for the enabled windows.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change; just add names for the primary/secondary/subordinate
bus numbers read from config space rather than repeatedly masking/shifting.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
With request_resource_conflict(), we can learn what the actual conflict is,
so print that info for debugging purposes.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
driver core: numa: fix BUILD_BUG_ON for node_read_distance
driver-core: document ERR_PTR() return values
kobject: documentation: Update to refer to kset-example.c.
sysdev: the cpu probe/release attributes should be sysdev_class_attributes
kobject: documentation: Fix erroneous example in kobject doc.
driver-core: fix missing kernel-doc in firmware_class
Driver core: Early platform kernel-doc update
sysfs: fix sysfs lockdep warning in mlx4 code
sysfs: fix sysfs lockdep warning in infiniband code
sysfs: fix sysfs lockdep warning in ipmi code
sysfs: Initialised pci bus legacy_mem field before use
sysfs: use sysfs_bin_attr_init in firmware class driver
pcix_get_mmrbc() returns the maximum memory read byte count (mmrbc), if
successful, or an appropriate error value, if not.
Distinguishing errors from correct values and understanding the meaning of an
error can be somewhat confusing in that:
correct values: 512, 1024, 2048, 4096
errors: -EINVAL -22
PCIBIOS_FUNC_NOT_SUPPORTED 0x81
PCIBIOS_BAD_VENDOR_ID 0x83
PCIBIOS_DEVICE_NOT_FOUND 0x86
PCIBIOS_BAD_REGISTER_NUMBER 0x87
PCIBIOS_SET_FAILED 0x88
PCIBIOS_BUFFER_TOO_SMALL 0x89
The PCIBIOS_ errors are returned from the PCI functions generated by the
PCI_OP_READ() and PCI_OP_WRITE() macros.
In a similar manner, pcix_set_mmrbc() also returns the PCIBIOS_ error values
returned from pci_read_config_[word|dword]() and pci_write_config_word().
Following pcix_get_max_mmrbc()'s example, the following patch simply returns
-EINVAL for all PCIBIOS_ errors encountered by pcix_get_mmrbc(), and -EINVAL
or -EIO for those encountered by pcix_set_mmrbc().
This simplification was chosen in light of the fact that none of the current
callers of these functions are interested in the specific type of error
encountered. In the future, should this change, one could simply create a
function that maps each PCIBIOS_ error to a corresponding unique errno value,
which could be called by pcix_get_max_mmrbc(), pcix_get_mmrbc(), and
pcix_set_mmrbc().
Additionally, this patch eliminates some unnecessary variables.
Cc: stable@kernel.org
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
An e1000 driver on a system with a PCI-X bus was always being returned
a value of 135 from both pcix_get_mmrbc() and pcix_set_mmrbc(). This
value reflects an error return of PCIBIOS_BAD_REGISTER_NUMBER from
pci_bus_read_config_dword(,, cap + PCI_X_CMD,).
This is because for a dword, the following portion of the PCI_OP_READ()
macro:
if (PCI_##size##_BAD) return PCIBIOS_BAD_REGISTER_NUMBER;
expands to:
if (pos & 3) return PCIBIOS_BAD_REGISTER_NUMBER;
And is always true for 'cap + PCI_X_CMD', which is 0xe4 + 2 = 0xe6. ('cap' is
the result of calling pci_find_capability(, PCI_CAP_ID_PCIX).)
The same problem exists for pci_bus_write_config_dword(,, cap + PCI_X_CMD,).
In both cases, instead of calling _dword(), _word() should be called.
Cc: stable@kernel.org
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When pci_register_set_vga_state() was made __init, the EXPORT_SYMBOL() was
retained, which now leaves us with a section mismatch.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: Mike Travis <travis@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For the PCI_X_STATUS register, pcix_get_max_mmrbc() is returning an incorrect
value, which is based on:
(stat & PCI_X_STATUS_MAX_READ) >> 12
Valid return values are 512, 1024, 2048, 4096, which correspond to a 'stat'
(masked and right shifted by 21) of 0, 1, 2, 3, respectively.
A right shift by 11 would generate the correct return value when 'stat' (masked
and right shifted by 21) has a value of 1 or 2. But for a value of 0 or 3 it's
not possible to generate the correct return value by only right shifting.
Fix is based on pcix_get_mmrbc()'s similar dealings with the PCI_X_CMD register.
Cc: stable@kernel.org
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PPC64 is failing to boot the latest mmotm due to an uninitialised pointer in
pci_create_legacy_files(). The surprise is that machines boot at all and it
would appear to affect current mainline as well. This patch fixes the problem.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze: (27 commits)
microblaze: entry.S use delay slot for return handlers
microblaze: Save current task directly
microblaze: Simplify entry.S - save/restore r3/r4 - ret_from_trap
microblaze: PCI early support for noMMU system
microblaze: Fix dma alloc and free coherent dma functions
microblaze: Add consistent code
microblaze: pgtable.h: move consistent functions
microblaze: Remove ancient Kconfig option for consistent mapping
microblaze: Remove VMALLOC_VMADDR
microblaze: Add define for ASM_LOOP
microblaze: Preliminary support for dma drivers
microblaze: remove trailing space in messages
microblaze: Use generic show_mem()
microblaze: Change temp register for cmdline
microblaze: Preliminary support for dma drivers
microblaze: Move cache function to cache.c
microblaze: Add support from PREEMPT
microblaze: Add support for Xilinx PCI host bridge
microblaze: Enable PCI, missing files
microblaze: Add core PCI files
...
Per ACPI spec, _ERG method should be executed before device driver
gets control for hotpluged device. Firmware might do some configuration
there. See http://bugzilla.kernel.org/show_bug.cgi?id=10805. In this
machine, _REG method of docked device will configure cardbus bridge.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Tested-by: Paul Martin <pm@debian.org>
Signed-off-by: Len Brown <len.brown@intel.com>
We can use pci-dma-compat.h to implement pci_set_dma_mask and
pci_set_consistent_dma_mask as we do with the other PCI DMA API.
We can remove HAVE_ARCH_PCI_SET_DMA_MASK too.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dma_set_coherent_mask corresponds to pci_set_consistent_dma_mask. This is
necessary to move to the generic device model DMA API from the PCI bus
specific API in the long term.
dma_set_coherent_mask works in the exact same way that
pci_set_consistent_dma_mask does. So this patch also changes
pci_set_consistent_dma_mask to call dma_set_coherent_mask.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@suse.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This changes pci_set_dma_mask to call the generic DMA API, dma_set_mask.
pci_set_dma_mask (in drivers/pci/pci.c) does the same things that
dma_set_mask does on all the architectures that use pci_set_dma_mask;
calls dma_supprted and sets dev->dma_mask. So we safely change
pci_set_dma_mask to simply call dma_set_mask.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@suse.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are two parts of changes. The first is just enable
PCI in Makefiles and in Kconfig. The second is the rest of
missing files. I didn't want to add it with previous patch
because that patch is too big.
Current Microblaze toolchain has problem with weak symbols
that's why is necessary to apply this changes to be possible
to compile pci support.
Xilinx knows about this problem.
Signed-off-by: Michal Simek <monstr@monstr.eu>
In the future, we are going to be changing the lock type for struct
device (once we get the lockdep infrastructure properly worked out) To
make that changeover easier, and to possibly burry the lock in a
different part of struct device, let's create some functions to lock and
unlock a device so that no out-of-core code needs to be changed in the
future.
This patch creates the device_lock/unlock/trylock() functions, and
converts all in-tree users to them.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Dave Young <hidave.darkstar@gmail.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <len.brown@intel.com>
Cc: Magnus Damm <damm@igel.co.jp>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Alex Chiang <achiang@hp.com>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrew Patterson <andrew.patterson@hp.com>
Cc: Yu Zhao <yu.zhao@intel.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: CHENG Renquan <rqcheng@smu.edu.sg>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Frans Pop <elendil@planet.nl>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After merging the final tree, today's linux-next build (powerpc
allyesconfig) failed like this:
drivers/pci/pci-sysfs.c: In function 'pci_create_legacy_files':
drivers/pci/pci-sysfs.c:645: error: lvalue required as unary '&' operand
drivers/pci/pci-sysfs.c:658: error: lvalue required as unary '&' operand
Caused by commit "sysfs: Use sysfs_attr_init and sysfs_bin_attr_init on
dynamic attributes" interacting with commit "sysfs: Use one lockdep
class per sysfs attribute") both from the driver-core tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These are the non-static sysfs attributes that exist on
my test machine. Fix them to use sysfs_attr_init or
sysfs_bin_attr_init as appropriate. It simply requires
making a sysfs attribute present to see this. So this
is a little bit tedious but otherwise not too bad.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Constify struct sysfs_ops.
This is part of the ops structure constification
effort started by Arjan van de Ven et al.
Benefits of this constification:
* prevents modification of data that is shared
(referenced) by many other structure instances
at runtime
* detects/prevents accidental (but not intentional)
modification attempts on archs that enforce
read-only kernel data at runtime
* potentially better optimized code as the compiler
can assume that the const data cannot be changed
* the compiler/linker move const data into .rodata
and therefore exclude them from false sharing
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes the iommu-api functions for mapping and
unmapping page ranges to use the new page-size based
interface. This allows to remove the range based functions
later.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The new function pointer names match better with the
top-level functions of the iommu-api which are using them.
Main intention of this change is to make the ->{un}map
pointer names free for two new mapping functions.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch solves nasty problem original driver has.
Original goal of the ricoh_mmc was to disable this device because then,
mmc cards can be read using standard SDHCI controller, thus avoiding
writing of yet another driver.
However, the act of disablement, makes other pci functions that belong to
this controller (xD and memstick) shift up one level, thus pci core has
now wrong idea about these devices.
To fix this issue, this patch moves the driver into the pci quirk section,
thus it is executes before the pci is enumerated, and therefore solving
that issue, also same sequence of commands is performed on resume for same
reasons.
Also regardless of the above, this way is cleaner. You still need to set
CONFIG_MMC_RICOH_MMC to enable this quirk
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Philip Langdale <philipl@overt.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the run-time power management of PCI devices be inactive by
default by calling pm_runtime_forbid() for each PCI device during its
initialization. This setting may be overriden by the user space with
the help of the /sys/devices/.../power/control interface.
That's necessary to avoid breakage on systems where ACPI-based
wake-up is known to fail for some devices.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'x86-bootmem-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
early_res: Need to save the allocation name in drop_range_partial()
sparsemem: Fix compilation on PowerPC
early_res: Add free_early_partial()
x86: Fix non-bootmem compilation on PowerPC
core: Move early_res from arch/x86 to kernel/
x86: Add find_fw_memmap_area
Move round_up/down to kernel.h
x86: Make 32bit support NO_BOOTMEM
early_res: Enhance check_and_double_early_res
x86: Move back find_e820_area to e820.c
x86: Add find_early_area_size
x86: Separate early_res related code from e820.c
x86: Move bios page reserve early to head32/64.c
sparsemem: Put mem map for one node together.
sparsemem: Put usemap for one node together
x86: Make 64 bit use early_res instead of bootmem before slab
x86: Only call dma32_reserve_bootmem 64bit !CONFIG_NUMA
x86: Make early_node_mem get mem > 4 GB if possible
x86: Dynamically increase early_res array size
x86: Introduce max_early_res and early_res_count
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1341 commits)
virtio_net: remove forgotten assignment
be2net: fix tx completion polling
sis190: fix cable detect via link status poll
net: fix protocol sk_buff field
bridge: Fix build error when IGMP_SNOOPING is not enabled
bnx2x: Tx barriers and locks
scm: Only support SCM_RIGHTS on unix domain sockets.
vhost-net: restart tx poll on sk_sndbuf full
vhost: fix get_user_pages_fast error handling
vhost: initialize log eventfd context pointer
vhost: logging thinko fix
wireless: convert to use netdev_for_each_mc_addr
ethtool: do not set some flags, if others failed
ipoib: returned back addrlen check for mc addresses
netlink: Adding inode field to /proc/net/netlink
axnet_cs: add new id
bridge: Make IGMP snooping depend upon BRIDGE.
bridge: Add multicast count/interval sysfs entries
bridge: Add hash elasticity/max sysfs entries
bridge: Add multicast_snooping sysfs toggle
...
Trivial conflicts in Documentation/feature-removal-schedule.txt
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: replace acpi_integer by u64
ACPICA: Update version to 20100121.
ACPICA: Remove unused uint32_struct type
ACPICA: Disassembler: Remove obsolete "Integer64" field in parse object
ACPICA: Remove obsolete ACPI_INTEGER (acpi_integer) type
ACPICA: Predefined name repair: fix NULL package elements
ACPICA: AcpiGetDevices: Eliminate unnecessary _STA calls
ACPICA: Update all ACPICA copyrights and signons to 2010
ACPICA: Update for new gcc-4 warning options
A ROM resource that doesn't fit should not cause us to try to re-assign
all the bus resources. Nobody generally cares, and re-assigning is
going to just cause way more troubles than it tries to solve.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-pci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Enable NMI on all cpus on UV
vgaarb: Add user selectability of the number of GPUS in a system
vgaarb: Fix VGA arbiter to accept PCI domains other than 0
x86, uv: Update UV arch to target Legacy VGA I/O correctly.
pci: Update pci_set_vga_state() to call arch functions
This patch adds the pci_vpd_find_info_keyword() helper function to
find information field keywords within read-only and read-write large
resource data type sections.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the pci_vpd_find_tag() helper function to find VPD
resource data types in a buffer.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set power.async_suspend for all PCI devices and PCIe port services,
so that they can be suspended and resumed in parallel with other
devices they don't depend on in a known way (i.e. devices which are
not their parents or children).
This only affects the "regular" suspend and resume stages, which
means in particular that the restoration of the PCI devices' standard
configuration registers during resume will still be carried out
synchronously (at the "early" resume stage).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Previously we used a table of size PCI_BUS_NUM_RESOURCES (16) for resources
forwarded to a bus by its upstream bridge. We've increased this size
several times when the table overflowed.
But there's no good limit on the number of resources because host bridges
and subtractive decode bridges can forward any number of ranges to their
secondary buses.
This patch reduces the table to only PCI_BRIDGE_RESOURCE_NUM (4) entries,
which corresponds to the number of windows a PCI-to-PCI (3) or CardBus (4)
bridge can positively decode. Any additional resources, e.g., PCI host
bridge windows or subtractively-decoded regions, are kept in a list.
I'd prefer a single list rather than this split table/list approach, but
that requires simultaneous changes to every architecture. This approach
only requires immediate changes where we set up (a) host bridges with more
than four windows and (b) subtractive-decode P2P bridges, and we can
incrementally change other architectures to use the list.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change; this converts loops that iterate from 0 to
PCI_BUS_NUM_RESOURCES through pci_bus resource[] table to use the
pci_bus_for_each_resource() iterator instead.
This doesn't change the way resources are stored; it merely removes
dependencies on the fact that they're in a table.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change; this fills in the bus subtractive decode resources
after reading the bridge window information rather than before. Also,
print out the subtractive decode resources as we already do for the
positive decode windows.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change; this breaks up pci_read_bridge_bases() into separate
pieces for the I/O, memory, and prefetchable memory windows, similar to how
Yinghai recently split up pci_setup_bridge() in 68e84ff3bdc.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe
capability offset. This reduces redundant search in PCI configuration
space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce run-time PM callbacks for the PCI bus type. Make the new
callbacks work in analogy with the existing system sleep PM
callbacks, so that the drivers already converted to struct dev_pm_ops
can use their suspend and resume routines for run-time PM without
modifications.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_is_pcie() instead of looking at obsolete is_pcie field in
struct pci_dev.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Although the majority of PCI devices can generate PMEs that in
principle may be used to wake up devices suspended at run time,
platform support is generally necessary to convert PMEs into wake-up
events that can be delivered to the kernel. If ACPI is used for this
purpose, PME signals generated by a PCI device will trigger the ACPI
GPE associated with the device to generate an ACPI wake-up event that
we can set up a handler for, provided that everything is configured
correctly.
Unfortunately, the subset of PCI devices that have GPEs associated
with them is quite limited. The devices without dedicated GPEs have
to rely on the GPEs associated with other devices (in the majority of
cases their upstream bridges and, possibly, the root bridge) to
generate ACPI wake-up events in response to PME signals from them.
Add ACPI platform support for PCI PME wake-up:
o Add a framework making is possible to use ACPI system notify
handlers for run-time PM.
o Add new PCI platform callback ->run_wake() to struct
pci_platform_pm_ops allowing us to enable/disable the platform to
generate wake-up events for given device. Implemet this callback
for the ACPI platform.
o Define ACPI wake-up handlers for PCI devices and PCI root buses and
make the PCI-ACPI binding code register wake-up notifiers for all
PCI devices present in the ACPI tables.
o Add function pci_dev_run_wake() which can be used by PCI drivers to
check if given device is capable of generating wake-up events at
run time.
Developed in cooperation with Matthew Garrett <mjg@redhat.com>.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Apparently, some machines may have problems with PCI run-time power
management if MSIs are used for the native PCIe PME signaling. In
particular, on the MSI Wind U-100 PCIe PME interrupts are not
generated by a PCIe root port after a resume from suspend to RAM, if
the system wake-up was triggered by a PME from the device attached to
this port. [It doesn't help to free the interrupt on suspend and
request it back on resume, even if that is done along with disabling
the MSI and re-enabling it, respectively.] However, if INTx
interrupts are used for this purpose on the same machine, everything
works just fine.
For this reason, add a kernel command line switch allowing one to
request that MSIs be not used for the native PCIe PME signaling,
introduce a DMI table allowing us to blacklist machines that need
this switch to be set by default and put the MSI Wind U-100 into this
table.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCIe native PME detection mechanism is based on interrupts generated
by root ports or event collectors every time a PCIe device sends a
PME message upstream.
Once a PME message has been sent by an endpoint device and received
by its root port (or event collector in the case of root complex
integrated endpoints), the Requester ID from the message header is
registered in the root port's Root Status register. At the same
time, the PME Status bit of the Root Status register is set to
indicate that there's a PME to handle. If PCIe PME interrupt is
enabled for the root port, it generates an interrupt once the PME
Status has been set. After receiving the interrupt, the kernel can
identify the PCIe device that generated the PME using the Requester
ID from the root port's Root Status register. [For details, see PCI
Express Base Specification, Rev. 2.0.]
Implement a driver for the PCIe PME root port service working in
accordance with the above description.
Based on a patch from Shaohua Li <shaohua.li@intel.com>.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add function pci_check_pme_status() that will check the PME status
bit of given device and clear it along with the PME enable bit. It
will be necessary for PCI run-time power management.
Based on a patch from Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Make pci_bridge_check_ranges() store the PCI_PREF_RANGE_TYPE_64 in
addition to IORESOURCE_MEM_64. Just like pci_read_bridge_bases().
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Handle the case where the slot bridge that doesn't get a pre-allocated
resource big enough to handle its child resources.. For example pcie
devices need 256M, but the bridge only gets 2M preallocated.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move bus_size_bridges and assign resources out of pciehp_add_bridge()
and do them all together, one time, including slot bridge, to avoid to
calling assign resources several times when there are several bridges
under the slot bridge. Using pci_assign_unassigned_bridge_resources.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For use by pciehp.
pci_setup_bridge() will not check enabled for the slot bridge, otherwise
update res is not updated to bridge BAR. That is, bridge is already
enabled for port service.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
BIOS separates IO ranges between several IOHs, and on some slots, BIOS assigns
resources to a bridge, but stops assigning resources to the device under that
bridge, because the device needs a big resource.
So:
1. allocate resources and record the failed device resources
2. clear the BIOS assigned resources of the parent bridge of failing device
3. go back and call pci assign unassigned
4. if it still fails, go up the tree, clear more bridges. and try again
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When clearing leaf bridge resources, trying to get a big enough one, we
could shrink the bridge if there is no resource under it. Confirm
against the old resource side to make sure we're increasing the
allocation.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We already track unassigned resources in struct resource, and this
prevents us from overwriting resource flags and info in the unassigned
case.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This allows us to track failed allocations for later re-trying with
reallocation.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We use this in later patches to free resrouce ranges for reassignment in
an effort to support a wider variety of PCI topologies.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add header file to fix build error:
drivers/pci/hotplug/ibmphp_hpc.c:135: error: implicit declaration of function 'init_MUTEX'
drivers/pci/hotplug/ibmphp_hpc.c:136: error: implicit declaration of function 'init_MUTEX_LOCKED'
drivers/pci/hotplug/ibmphp_hpc.c:797: error: implicit declaration of function 'down'
drivers/pci/hotplug/ibmphp_hpc.c:807: error: implicit declaration of function 'up'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Yinghai pointed out that the new pci_scan_slot() crashes when called
on an ARI-capable slot that is empty. Fix this by exiting early from
pci_scan_slot if there is no device in the slot.
Also make next_ari_func() robust against devices not existing in case
the ARI capability is corrupt. ARI also requires that the devices be
listed in order, so if we find a function listed that is out of order,
stop scanning to prevent loops.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Stanse found an ommitted pci_dev_put on one error path in
cpcihp_generic_init. The path is taken on !dev, but also when
dev->hdr_type != PCI_HEADER_TYPE_BRIDGE. However it omits to
pci_dev_put on the latter.
As it is fine to pass NULL to pci_dev_put, put it in there
uncoditionally.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Scott Murray <scott@spiteful.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The ISDN4Linux HiSax driver family contains the last remaining users
of the deprecated pci_find_device() function. This patch creates a
private copy of that function in HiSax, and removes the now unused
global function together with its controlling configuration option,
CONFIG_PCI_LEGACY.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Don't print out resources without flags to avoid cluttering up the debug
output.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This is a good cleanup in itself, and makes it easier to modify specific
resource types in later code.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ibmphp driver currently maps only 1KB of ebda memory area into kernel address
space during driver initialization. This causes kernel oops when the driver is
modprobe'd and it accesses memory beyond 1KB within ebda segment. The first
byte of ebda segment actually stores the length of the ebda region in
Kilobytes. Hence make use of the length parameter and map the entire ebda
region.
Signed-off-by: Chandru Siddalingappa <chandru@linux.vnet.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Stanse found a cut&pasted memory leak in pciehp_queue_pushbutton_work
and shpchp_queue_pushbutton_work. info is not freed/assigned on all
paths. Fix that.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Now that we return the new resource start position, there is no
need to update "struct resource" inside the align function.
Therefore, mark the struct resource as const.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As suggested by Linus, align functions should return the start
of a resource, not void. An update of "res->start" is no longer
necessary.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently, drivers/pci/quirks.c is built unconditionally, but if
CONFIG_PCI_QUIRKS is unset, the only things actually built in this
file are definitions of global variables and empty functions (due to
the #ifdef CONFIG_PCI_QUIRKS embracing all of the code inside the
file). This is not particularly nice and if someone overlooks
the #ifdef CONFIG_PCI_QUIRKS, build errors are introduced.
To clean that up, move the definitions of the global variables in
quirks.c that are always built to pci.c, move the definitions of
the empty functions (compiled when CONFIG_PCI_QUIRKS is unset) to
headers (additionally make these functions static inline) and modify
drivers/pci/Makefile so that quirks.c is only built if
CONFIG_PCI_QUIRKS is set.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No longer needed and causes build breakage.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Take advantage of some gaps in the table to fit in support for AGP speeds.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Both PCIe and PCI-X bridges report their secondary bus speed in their
respective capabilities.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move the max_bus_speed and cur_bus_speed into the pci_bus. Expose the
values through the PCI slot driver instead of the hotplug slot driver.
Update all the hotplug drivers to use the pci_bus instead of their own
data structures.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These enums must not overlap anyway, since we only have a single
pci_bus_speed_strings array. Use a single enum, and move it to
pci.h. Add 'SPEED' to the pcie names to make it clear what they are.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The Alternate Routing-ID Interpretation capability allows a single device
to have up to 256 functions. They can be populated sparsely, so the
current technique of scanning every eighth function is not guaranteed
to find them all. By introducing a 'next_fn' function pointer, we can
use the linked list of functions in the ARI capability to scan all the
functions which exist.
We can then speed up the pci_scan_slot by skipping the scan of subsequent
devfns for PCIe devices which are the direct children of Root Ports or
Downstream Ports. These devices are only permitted to implement device
0, unless they are ARI devices, in which case they'll be scanned by the
ARI code above.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds support for the 82576NS Serdes adapter to the existing pci
quirk for 82576 parts.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For use by code that needs to walk extended capability lists before
pci_dev structures are set up.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <43F901BD926A4E43B106BF17856F07559FB80CFD@orsmsx508.amr.corp.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add and export pci_num_vf to allow other subsystems to determine how many
virtual function devices are associated with an SR-IOV physical function
device.
Add macros dev_is_pci, dev_is_ps, and dev_num_vf to make it easier for
non-PCI specific code to determine SR-IOV capabilities.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename add_range() to add_bus_range() to avoid conflict with the
naming of the generic range manipulation functions.
LKML-Reference: <1265793639-15071-4-git-send-email-yinghai@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Update pci_set_vga_state to call arch dependent functions to enable Legacy
VGA I/O transactions to be redirected to correct target.
[akpm@linux-foundation.org: make pci_register_set_vga_state() __init]
Signed-off-by: Mike Travis <travis@sgi.com>
LKML-Reference: <201002022238.o12McE1J018723@imap1.linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Robin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The new cs5535-* drivers use PCI header config info rather than MSRs to
determine the memory region to use for things like GPIOs and MFGPTs. As
anticipated, we've run into a buggy BIOS:
[ 0.081818] pci 0000:00:14.0: reg 10: [io 0x6000-0x7fff]
[ 0.081906] pci 0000:00:14.0: reg 14: [io 0x6100-0x61ff]
[ 0.082015] pci 0000:00:14.0: reg 18: [io 0x6200-0x63ff]
[ 0.082917] pci 0000:00:14.2: reg 20: [io 0xe000-0xe00f]
[ 0.083551] pci 0000:00:15.0: reg 10: [mem 0xa0010000-0xa0010fff]
[ 0.084436] pci 0000:00:15.1: reg 10: [mem 0xa0011000-0xa0011fff]
[ 0.088816] PCI: pci_cache_line_size set to 32 bytes
[ 0.088938] pci 0000:00:14.0: address space collision: [io 0x6100-0x61ff] already in use
[ 0.089052] pci 0000:00:14.0: can't reserve [io 0x6100-0x61ff]
This is a Soekris board, and its BIOS sets the size of the PCI ISA bridge
device's BAR0 to 8k. In reality, it should be 8 bytes (BAR0 is used for
SMBus stuff). This quirk checks for an incorrect size, and resets it
accordingly.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Tested-by: Leigh Porter <leigh@leighporter.org>
Tested-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Callers (acpi_memhotplug.c, dock.c and others) check for the return
value of acpi_bus_add() and assume a valid device was returned in
case zero was returned.
Thus return -ENODEV if no device was found in acpi_bus_scan and
propagate this through acpi_bus_add and acpi_bus_start.
Also remove a confusing comment in acpiphp_glue.c, acpi_bus_scan
will and cannot invoke if acpi_bus_add returns no valid device.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We are missing these when building the pci_dev from scratch off
the Open Firmware device-tree
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
acpi_integer is now obsolete and removed from the ACPICA code base,
replaced by u64.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The aer_inject module hangs in aer_inject() when checking the device's
error masks. The hang is due to a recursive use of the aer_inject lock.
The aer_inject() routine grabs the lock while processing the error and then
calls pci_read_config_dword to read the masks. The pci_read_config_dword
routine is earlier overridden by pci_read_aer, which among other things,
grabs the aer_inject lock.
Fixed by moving the pci_read_config_dword calls to read the masks to before
the lock is taken.
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The Correcteable/Uncorrectable Error Mask Registers are used by PCIe AER
driver which will controls the reporting of individual errors to PCIe RC
via PCIe error messages.
If hardware masks special error reporting to RC, the aer_inject driver
should not inject aer error.
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Youquan, Song <youquan.song@intel.com>
Acked-by: Ying, Huang <ying.huang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It turns out that some PCI devices require extra delays when changing
power state from D3 to D0 (and the other way around). Although this
is against the PCI specification, we can handle it quite easily by
allowing drivers to define arbitrary D3 delays for devices known to
require extra time for switching power states.
Introduce additional field d3_delay in struct pci_dev and use it to
store the value of the device's D0->D3 delay, in miliseconds. Make
the PCI PM core code use the per-device d3_delay unless
pci_pm_d3_delay is greater (in which case the latter is used).
[This also allows the driver to specify d3_delay shorter than the
10 ms required by the PCI standard if the device is known to be able
to handle that.]
Make the sky2 driver set d3_delay to 150 for devices handled by it.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=14730 which is a
listed regression from 2.6.30.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit e0cd516 "PCI: derive nearby CPUs from device's instead of bus'
NUMA information" causes an null pointer dereference when reading from
the sysfs attributes local_cpu* on Intel machines with no ACPI NUMA
proximity info, since dev->numa_node gets set to -1 for all PCI devices,
which then gets passed to cpumask_of_node.
Add a check to prevent this.
Signed-off-by: David John <davidjon@xenontk.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduced by commit 5b889bf23 ("PCI: Fix build if quirks are not
enabled"), which made the pci_dev_reset_methods[] array static and
'const', but didn't then change the code to match, and use a const
pointer when moving it to quirks.c.
Trivially fixed by just adding the required 'const' to the iterator
variable.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After commit b9c3b26641 ("PCI: support
device-specific reset methods") the kernel build is broken if
CONFIG_PCI_QUIRKS is unset.
Fix this by moving pci_dev_specific_reset() to drivers/pci/quirks.c and
providing an empty replacement for !CONFIG_PCI_QUIRKS builds.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dmar_tbl is declared as __initdata, but dmar_ir_support() is not declared
as an __init function. Fix is simple since the only caller of dmar_ir_support
(intr_remapping_supported) is an __init function.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI/cardbus: Add a fixup hook and fix powerpc
PCI: change PCI nomenclature in drivers/pci/ (non-comment changes)
PCI: change PCI nomenclature in drivers/pci/ (comment changes)
PCI: fix section mismatch on update_res()
PCI: add Intel 82599 Virtual Function specific reset method
PCI: add Intel USB specific reset method
PCI: support device-specific reset methods
PCI: Handle case when no pci device can provide cache line size hint
PCI/PM: Propagate wake-up enable for PCIe devices too
vgaarbiter: fix a typo in the vgaarbiter Documentation
The cardbus code creates PCI devices without ever going through the
necessary fixup bits and pieces that normal PCI devices go through.
There's in fact a commented out call to pcibios_fixup_bus() in there,
it's commented because ... it doesn't work.
I could make pcibios_fixup_bus() do the right thing on powerpc easily
but I felt it cleaner instead to provide a specific hook pci_fixup_cardbus
for which a weak empty implementation is provided by the PCI core.
This fixes cardbus on powerbooks and probably all other PowerPC
platforms which was broken completely for ever on some platforms and
since 2.6.31 on others such as PowerBooks when we made the DMA ops
mandatory (since those are setup by the fixups).
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Changing occurrences of variants of PCI-X and PCIe to the PCI-SIG
terms listed in the "Trademark and Logo Usage Guidelines".
http://www.pcisig.com/developers/procedures/logos/Trademark_and_Logo_Usage_Guidelines_updated_112206.pdf
Patch is limited to drivers/pci/ and changes concern non-comment parts or
anything that might be visible to the user.
Signed-off-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Handle device specific timeout and use FLR.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Dexuan Cui <dexuan.cui@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add a new type of quirk for resetting devices at pci_dev_reset time.
This is necessary to handle device with nonstandard reset procedures,
especially useful for guest drivers.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Dexuan Cui <dexuan.cui@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Prior to this patch, if pci_read_config_byte(dev, PCI_CACHE_LINE_SIZE, ...)
returns 0 for all dev, pci_cache_line_size ends up set to zero
(instead of pci_dfl_cache_line_size).
This patch ensures the pci_cache_line_size = pci_dfl_cache_line_size
setting in the above scenario.
This happens in case of a kvm-88 guest (where, consequently, the rtl8139
NIC failed to initialize).
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Csaba Henk <csaba@gluster.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Having read the PM part of the PCIe 2.0 specification more carefully
I think that it was a mistake to restrict the wake-up enable
propagation to non-PCIe devices, because if we do not request
control of the root ports' PME registers via OSC, PCIe PME is
supposed to be handled by the platform, just like the non-PCIe PME.
Even if we do that, the wake-up propagation is done to allow the
devices to wake up the system from sleep states which involves the
platform anyway, so it won't hurt.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* git://git.infradead.org/iommu-2.6:
implement early_io{re,un}map for ia64
Revert "Intel IOMMU: Avoid memory allocation failures in dma map api calls"
intel-iommu: ignore page table validation in pass through mode
intel-iommu: Fix oops with intel_iommu=igfx_off
intel-iommu: Check for an RMRR which ends before it starts.
intel-iommu: Apply BIOS sanity checks for interrupt remapping too.
intel-iommu: Detect DMAR in hyperspace at probe time.
dmar: Fix build failure without NUMA, warn on bogus RHSA tables and don't abort
iommu: Allocate dma-remapping structures using numa locality info
intr_remap: Allocate intr-remapping table using numa locality info
dmar: Allocate queued invalidation structure using numa locality info
dmar: support for parsing Remapping Hardware Static Affinity structure
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPICA: Update version to 20091112.
ACPICA: Add additional module-level code support
ACPICA: Deploy new create integer interface where appropriate
ACPICA: New internal utility function to create Integer objects
ACPICA: Add repair for predefined methods that must return sorted lists
ACPICA: Fix possible fault if return Package objects contain NULL elements
ACPICA: Add post-order callback to acpi_walk_namespace
ACPICA: Change package length error message to an info message
ACPICA: Reduce severity of predefined repair messages, Warning to Info
ACPICA: Update version to 20091013
ACPICA: Fix possible memory leak for Scope ASL operator
ACPICA: Remove possibility of executing _REG methods twice
ACPICA: Add repair for bad _MAT buffers
ACPICA: Add repair for bad _BIF/_BIX packages
* 'timers-for-linus-hpet' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: hpet: Make WARN_ON understandable
x86: arch specific support for remapping HPET MSIs
intr-remap: generic support for remapping HPET MSIs
x86, hpet: Simplify the HPET code
x86, hpet: Disable per-cpu hpet timer if ARAT is supported
commit eb3fa7cb51 said Intel IOMMU
Intel IOMMU driver needs memory during DMA map calls to setup its
internal page tables and for other data structures. As we all know
that these DMA map calls are mostly called in the interrupt context
or with the spinlock held by the upper level drivers(network/storage
drivers), so in order to avoid any memory allocation failure due to
low memory issues, this patch makes memory allocation by temporarily
setting PF_MEMALLOC flags for the current task before making memory
allocation calls.
We evaluated mempools as a backup when kmem_cache_alloc() fails
and found that mempools are really not useful here because
1) We don't know for sure how much to reserve in advance
2) And mempools are not useful for GFP_ATOMIC case (as we call
memory alloc functions with GFP_ATOMIC)
(akpm: point 2 is wrong...)
The above description doesn't justify to waste system emergency memory
at all. Non MM subsystem must not use PF_MEMALLOC. Memory reclaim need
few memory, anyone must not prevent it. Otherwise the system cause
mysterious hang-up and/or OOM Killer invokation.
Plus, akpm already pointed out what we should do.
Then, this patch revert it.
Cc: Keshavamurthy Anil S <anil.s.keshavamurthy@intel.com>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We are seeing a bug when booting w/ iommu=pt with current upstream
(bisect blames 19943b0e30 "intel-iommu:
Unify hardware and software passthrough support).
The issue is specific to this loop during identity map initialization
of each device:
domain_context_mapping_one(si_domain, ..., CONTEXT_TT_PASS_THROUGH)
...
/* Skip top levels of page tables for
* iommu which has less agaw than default.
*/
for (agaw = domain->agaw; agaw != iommu->agaw; agaw--) {
pgd = phys_to_virt(dma_pte_addr(pgd));
if (!dma_pte_present(pgd)) { <------ failing here
spin_unlock_irqrestore(&iommu->lock, flags);
return -ENOMEM;
}
This box has 2 iommu's in it. The catchall iommu has MGAW == 48, and
SAGAW == 4. The other iommu has MGAW == 39, SAGAW == 2.
The device that's failing the above pgd test is the only device connected
to the non-catchall iommu, which has a smaller address width than the
domain default. This test is not necessary since the context is in PT
mode and the ASR is ignored.
Thanks to Don Dutile for discovering and debugging this one.
Cc: stable@kernel.org
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The hotplug notifier will call find_domain() to see if the device in
question has been assigned an IOMMU domain. However, this should never
be called for devices with a "dummy" domain, such as graphics devices
when intel_iommu=igfx_off is set and the corresponding IOMMU isn't even
initialised. If you do that, it'll oops as it dereferences the (-1)
pointer.
The notifier function should check iommu_no_mapping() for the
device before doing anything else.
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some HP BIOSes report an RMRR region (a region which needs a 1:1 mapping
in the IOMMU for a given device) which has an end address lower than its
start address. Detect that and warn, rather than triggering the
BUG() in dma_pte_clear_range().
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The BIOS errors where an IOMMU is reported either at zero or a bogus
address are causing problems even when the IOMMU is disabled -- because
interrupt remapping uses the same hardware. Ensure that the checks get
applied for the interrupt remapping initialisation too.
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Many BIOSes will lie to us about the existence of an IOMMU, and claim
that there is one at an address which actually returns all 0xFF.
We need to detect this early, so that we know we don't have a viable
IOMMU and can set up swiotlb before it's too late.
Cc: stable@kernel.org
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (63 commits)
x86, Calgary IOMMU quirk: Find nearest matching Calgary while walking up the PCI tree
x86/amd-iommu: Remove amd_iommu_pd_table
x86/amd-iommu: Move reset_iommu_command_buffer out of locked code
x86/amd-iommu: Cleanup DTE flushing code
x86/amd-iommu: Introduce iommu_flush_device() function
x86/amd-iommu: Cleanup attach/detach_device code
x86/amd-iommu: Keep devices per domain in a list
x86/amd-iommu: Add device bind reference counting
x86/amd-iommu: Use dev->arch->iommu to store iommu related information
x86/amd-iommu: Remove support for domain sharing
x86/amd-iommu: Rearrange dma_ops related functions
x86/amd-iommu: Move some pte allocation functions in the right section
x86/amd-iommu: Remove iommu parameter from dma_ops_domain_alloc
x86/amd-iommu: Use get_device_id and check_device where appropriate
x86/amd-iommu: Move find_protection_domain to helper functions
x86/amd-iommu: Simplify get_device_resources()
x86/amd-iommu: Let domain_for_device handle aliases
x86/amd-iommu: Remove iommu specific handling from dma_ops path
x86/amd-iommu: Remove iommu parameter from __(un)map_single
x86/amd-iommu: Make alloc_new_range aware of multiple IOMMUs
...
Remove a stray space in pci_save_state().
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit ae21ee65e8 "PCI: acs p2p upsteram
forwarding enabling" doesn't actually enable ACS.
Add a function to pci core to allow an IOMMU to request that ACS
be enabled. The existing mechanism of using iommu_found() in the pci
core to know when ACS should be enabled doesn't actually work due to
initialization order; iommu has only been detected not initialized.
Have Intel and AMD IOMMUs request ACS, and Xen does as well during early
init of dom0.
Cc: Allen Kay <allen.m.kay@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This problem happened when removing PCIe root port using PCI logical
hotplug operation.
The immediate cause of this problem is that the pointer to invalid
data structure is passed to pcie_update_aspm_capable() by
pcie_aspm_exit_link_state(). When pcie_aspm_exit_link_state() received
a pointer to root port link, it unconfigures the root port link and
frees its data structure at first. At this point, there are not links
to configure under the root port and the data structure for root port
link is already freed. So pcie_aspm_exit_link_state() must not call
pcie_update_aspm_capable() and pcie_config_aspm_path().
This patch fixes the problem by changing pcie_aspm_exit_link_state()
not to call pcie_update_aspm_capable() and pcie_config_aspm_path() if
the specified link is root port link.
------------[ cut here ]------------
kernel BUG at drivers/pci/pcie/aspm.c:606!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
last sysfs file: /sys/devices/pci0000:40/0000:40:13.0/remove
CPU 1
Modules linked in: shpchp
Pid: 9345, comm: sysfsd Not tainted 2.6.32-rc5 #98 ProLiant DL785 G6
RIP: 0010:[<ffffffff811df69b>] [<ffffffff811df69b>] pcie_update_aspm_capable+0x15/0xbe
RSP: 0018:ffff88082a2f5ca0 EFLAGS: 00010202
RAX: 0000000000000e77 RBX: ffff88182cc3e000 RCX: ffff88082a33d006
RDX: 0000000000000001 RSI: ffffffff811dff4a RDI: ffff88182cc3e000
RBP: ffff88082a2f5cc0 R08: ffff88182cc3e000 R09: 0000000000000000
R10: ffff88182fc00180 R11: ffff88182fc00198 R12: ffff88182cc3e000
R13: 0000000000000000 R14: ffff88182cc3e000 R15: ffff88082a2f5e20
FS: 00007f259a64b6f0(0000) GS:ffff880864600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 00007feb53f73da0 CR3: 000000102cc94000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process sysfsd (pid: 9345, threadinfo ffff88082a2f4000, task ffff88082a33cf00)
Stack:
ffff88182cc3e000 ffff88182cc3e000 0000000000000000 ffff88082a33cf00
<0> ffff88082a2f5cf0 ffffffff811dff52 ffff88082a2f5cf0 ffff88082c525168
<0> ffff88402c9fd2f8 ffff88402c9fd2f8 ffff88082a2f5d20 ffffffff811d7db2
Call Trace:
[<ffffffff811dff52>] pcie_aspm_exit_link_state+0xf5/0x11e
[<ffffffff811d7db2>] pci_stop_bus_device+0x76/0x7e
[<ffffffff811d7d67>] pci_stop_bus_device+0x2b/0x7e
[<ffffffff811d7e4f>] pci_remove_bus_device+0x15/0xb9
[<ffffffff811dcb8c>] remove_callback+0x29/0x3a
[<ffffffff81135aeb>] sysfs_schedule_callback_work+0x15/0x6d
[<ffffffff81072790>] worker_thread+0x19d/0x298
[<ffffffff8107273b>] ? worker_thread+0x148/0x298
[<ffffffff81135ad6>] ? sysfs_schedule_callback_work+0x0/0x6d
[<ffffffff810765c0>] ? autoremove_wake_function+0x0/0x38
[<ffffffff810725f3>] ? worker_thread+0x0/0x298
[<ffffffff8107629e>] kthread+0x7d/0x85
[<ffffffff8102eafa>] child_rip+0xa/0x20
[<ffffffff8102e4bc>] ? restore_args+0x0/0x30
[<ffffffff81076221>] ? kthread+0x0/0x85
[<ffffffff8102eaf0>] ? child_rip+0x0/0x20
Code: 89 e5 8a 50 48 31 c0 c0 ea 03 83 e2 07 e8 b2 de fe ff c9 48 98 c3 55 48 89 e5 41 56 49 89 fe 41 55 41 54 53 48 83 7f 10 00 74 04 <0f> 0b eb fe 48 8b 05 da 7d 63 00 4c 8d 60 e8 4c 89 e1 eb 24 4c
RIP [<ffffffff811df69b>] pcie_update_aspm_capable+0x15/0xbe
RSP <ffff88082a2f5ca0>
---[ end trace 6ae0f65bdeab8555 ]---
Reported-by: Alex Chiang <achiang@hp.com>
Tested-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The pci_cleanup_aer_correct_error_status() function has been
#if 0'd out since 2.6.25. Time to remove the dead code.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The current implementation of pci_cleanup_aer_uncorrect_error_status
only clears either fatal or non-fatal error status bits depending
on the state of the I/O channel. This implementation will then often
leave some bits set after PCI error recovery completes. The uncleared bit
settings will then be falsely reported the next time an AER interrupt is
generated for that hierarchy. An easy way to illustrate this issue is to
use the aer-inject module to simultaneously inject both an uncorrectable
non-fatal and uncorrectable fatal error. One of the errors will not be
cleared.
This patch resolves this issue by unconditionally clearing all bits in
the AER uncorrectable status register. All settings and corrective action
strategies are saved and determined before
pci_cleanup_aer_uncorrect_error_status is called, so this change should not
affect errory handling functionality.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove 'port_type' field in struct pcie_port_data(), because we can
get port type information from struct pci_dev. With this change, this
patch also does followings:
- Remove struct pcie_port_data because it no longer has any field.
- Remove portdrv private definitions about port type (PCIE_RC_PORT,
PCIE_SW_UPSTREAM_PORT and PCIE_SW_DOWNSTREAM_PORT), and use generic
definitions instead.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add missing service irqs cleanup in the error code path of
pcie_port_device_register().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Call pci_enable_device() before initializing service irqs, because
legacy interrupt is initialized in pci_enable_device() on some
architectures.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch cleans up the service irqs initialization as follows:
- Remove 'irq_mode' field in pcie_port_data and related definitions,
which is not needed because we can get the same information from
'is_msix', 'is_msi' and 'pin' fields in struct pci_dev.
- Change the name of 'vectors' argument of assign_interrupt_mode() to
'irqs' because it holds irq numbers actually. People might confuse
it with CPU vector or MSI/MSI-X vector.
- Change function name assign_interrupt_mode() to init_service_irqs()
becasuse we no longer have 'irq_mode' data structure, and new name
is more straightforward (IMO).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No reason to check PME capability outside get_port_device_capability().
Do it in get_port_device_capability().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCIe port type is already stored in 'pcie_type' field of struct
pci_dev. So we don't need to get it from pci configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In the current port bus driver implementation, pcie_device allocation,
initialization and registration are done in separated functions. Doing
those in one function make the code simple and easier to read.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We don't need pcie_port_device_probe() because we can get pci
device/port type using pci_is_pcie() and 'pcie_type' fields in struct
pci_dev. Remove pcie_port_device_probe().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Prior to 1f82de10 we always initialized the upper 32bits of the
prefetchable memory window, regardless of the address range used.
Now we only touch it for a >32bit address, which means the upper32
registers remain whatever the BIOS initialized them too.
It's valid for the BIOS to set the upper32 base/limit to
0xffffffff/0x00000000, which makes us program prefetchable ranges
like 0xffffffffabc00000 - 0x00000000abc00000
Revert the chunk of 1f82de10 that made this conditional so we always
write the upper32 registers and remove now unused pref_mem64 variable.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The pcie_flr routine writes the device control register with the FLR bit
set clearing all other fields for the FLR duration. Among other fields,
the Max_Payload_Size is also cleared which can cause errors if there are
transactions lurking in the HW pipeline. The patch replaces the blank
write with read-modify-write of the control register keeping the other
fields intact.
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
So we can catch if the driver sets an incorrect dma_mask.
Reviewed-by: Grant Grundler <grundler@google.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If we stop the kthread, we may end up up'ing the sem twice, which seems
unintended.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The existing interface only has a pre-order callback. This change
adds an additional parameter for a post-order callback which will
be more useful for bus scans. ACPICA BZ 779.
Also update the external calls to acpi_walk_namespace.
http://www.acpica.org/bugzilla/show_bug.cgi?id=779
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Enabling power fault detected event notification in current pciehp
might cause power fault interrupt storm on some machines. On those
machines. On those machines, power fault detected bit in the slot
status register was set again immediately when it is cleared in the
interrupt service routine, and next power fault detected interrupt was
notified again. Therefore, disable power fault detected event
notification for now.
This patch also removes unnecessary handling for power fault cleared
event because this event is not supported by PCIe spec.
Tested-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Change for PCI hotplug to use pci_is_pcie() instead of checking
pci_dev->is_pcie.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Changes for PCIe AER driver to use pci_is_pcie() instead of checking
pci_dev->is_pcie.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Change for PCIe ASPM driver to use pci_is_pcie() instead of checking
pci_dev->is_pcie.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Change for PCI core to use pci_is_pcie() instead of checking
pci_dev->is_pcie.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in pciehp driver. This avoids unnecessary search in PCI
configuration space. This patch also removes 'cap_base' field in
struct controller, that was used to hold PCIe capability offset by
pciehp itself.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCI hotplug core. This avoids unnecessary search in PCI
configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCIe ASPM driver. This avoids unnecessary search in PCI
configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCI Express Port Bus driver. This avoids unnecessary serarch
in PCI configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCIe AER driver. This avoids unnecessary search in PCI
configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCI core code. This avoids unnecessary search in PCI
configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 86cf898e1d ("intel-iommu: Check for
'DMAR at zero' BIOS error earlier.") was supposed to work by pretending
not to detect an IOMMU if it was actually being reported by the BIOS at
physical address zero.
However, the intel_iommu_init() function is called unconditionally, as
are the corresponding functions for other IOMMU hardware.
So the patch only worked if you have RAM above the 4GiB boundary. It
caused swiotlb to be initialised when no IOMMU was detected during early
boot, and thus the later IOMMU init would refuse to run.
But if you have less RAM than that, swiotlb wouldn't get set up and the
IOMMU _would_ still end up being initialised, even though we never
claimed to detect it.
This patch also sets the dmar_disabled flag when the error is detected
during the initial detection phase -- so that the later call to
intel_iommu_init() will return without doing anything, regardless of
whether swiotlb is used or not.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/users/dwmw2/iommu-2.6.32:
intel-iommu: Support PCIe hot-plug
intel-iommu: Obey coherent_dma_mask for alloc_coherent on passthrough
intel-iommu: Check for 'DMAR at zero' BIOS error earlier.
To support PCIe hot plug in IOMMU, we register a notifier to respond to device
change action.
When the notifier gets BUS_NOTIFY_UNBOUND_DRIVER, it removes the device
from its DMAR domain.
A hot added device will be added into an IOMMU domain when it first does IOMMU
op. So there is no need to add more code for hot add.
Without the patch, after a hot-remove, a hot-added device on the same
slot will not work.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The model for IOMMU passthrough is that decent devices that can cope
with DMA to all of memory get passthrough; crappy devices with a limited
dma_mask don't -- they get to use the IOMMU anyway.
This is done on the basis that IOMMU passthrough is usually wanted for
performance reasons, and it's only the decent PCI devices that you
really care about performance for, while the crappy 32-bit ones like
your USB controller can just use the IOMMU and you won't really care.
Unfortunately, the check for this was only looking at dev->dma_mask, not
at dev->coherent_dma_mask. And some devices have a 32-bit
coherent_dma_mask even though they have a full 64-bit dma_mask.
Even more unfortunately, fixing that simple oversight would upset
certain broken HP devices. Not only do they have a 32-bit
coherent_dma_mask, but they also have a tendency to do stray DMA to
unmapped addresses. And then they die when they take the DMA fault they
so richly deserve.
So if we do the 'correct' fix, it'll mean that affected users have to
disable IOMMU support completely on "a large percentage of servers from
a major vendor."
Personally, I have little sympathy -- given that this is the _same_
'major vendor' who is shipping machines which claim to have IOMMU
support but have obviously never _once_ booted a VT-d capable OS to do
any form of QA. But strictly speaking, it _would_ be a regression even
though it only ever worked by fluke.
For 2.6.33, we'll come up with a quirk which gives swiotlb support
for this particular device, and other devices with an inadequate
coherent_dma_mask will just get normal IOMMU mapping.
The simplest fix for 2.6.32, though, is just to jump through some hoops
to try to allocate coherent DMA memory for such devices in a place that
they can reach. We'd use dma_generic_alloc_coherent() for this if it
existed on IA64.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
I'm not entirely sure it needs to go into 32, but it's probably the right
thing to do. Another way of explaining the patch is:
- we currently pick the _first_ exactly matching bus resource entry, but
the _last_ inexactly matching one. Normally first/last shouldn't
matter, but bus resource entries aren't actually all created equal: in
a transparent bus, the last resources will be the parent resources,
which we should generally try to avoid unless we have no choice. So
"first matching" is the thing we should always aim for.
- the patch is a bit bigger than it needs to be, because I simplified the
logic at the same time. It used to be a fairly incomprehensible
if ((res->flags & IORESOURCE_PREFETCH) && !(r->flags & IORESOURCE_PREFETCH))
best = r; /* Approximating prefetchable by non-prefetchable */
and technically, all the patch did was to make that complex choice be
even more complex (it basically added a "&& !best" to say that if we
already gound a non-prefetchable window for the prefetchable resource,
then we won't override an earlier one with that later one: remember
"first matching").
- So instead of that complex one with three separate conditionals in one,
I split it up a bit, and am taking advantage of the fact that we
already handled the exact case, so if 'res->flags' has the PREFETCH
bit, then we already know that 'r->flags' will _not_ have it. So the
simplified code drops the redundant test, and does the new '!best' test
separately. It also uses 'continue' as a way to ignore the bus
resource we know doesn't work (ie a prefetchable bus resource is _not_
acceptable for anything but an exact match), so it turns into:
/* We can't insert a non-prefetch resource inside a prefetchable parent .. */
if (r->flags & IORESOURCE_PREFETCH)
continue;
/* .. but we can put a prefetchable resource inside a non-prefetchable one */
if (!best)
best = r;
instead. With the comments, it's now six lines instead of two, but it's
conceptually simpler, and I _could_ have written it as two lines:
if ((res->flags & IORESOURCE_PREFETCH) && !best)
best = r; /* Approximating prefetchable by non-prefetchable */
but I thought that was too damn subtle.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If HW IOMMU initialization fails (Intel VT-d often does this,
typically due to BIOS bugs), we fall back to nommu. It doesn't
work for the majority since nowadays we have more than 4GB
memory so we must use swiotlb instead of nommu.
The problem is that it's too late to initialize swiotlb when HW
IOMMU initialization fails. We need to allocate swiotlb memory
earlier from bootmem allocator. Chris explained the issue in
detail:
http://marc.info/?l=linux-kernel&m=125657444317079&w=2
The current x86 IOMMU initialization sequence is too complicated
and handling the above issue makes it more hacky.
This patch changes x86 IOMMU initialization sequence to handle
the above issue cleanly.
The new x86 IOMMU initialization sequence are:
1. we initialize the swiotlb (and setting swiotlb to 1) in the case
of (max_pfn > MAX_DMA32_PFN && !no_iommu). dma_ops is set to
swiotlb_dma_ops or nommu_dma_ops. if swiotlb usage is forced by
the boot option, we finish here.
2. we call the detection functions of all the IOMMUs
3. the detection function sets x86_init.iommu.iommu_init to the
IOMMU initialization function (so we can avoid calling the
initialization functions of all the IOMMUs needlessly).
4. if the IOMMU initialization function doesn't need to swiotlb
then sets swiotlb to zero (e.g. the initialization is
sucessful).
5. if we find that swiotlb is set to zero, we free swiotlb
resource.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: chrisw@sous-sol.org
Cc: dwmw2@infradead.org
Cc: joerg.roedel@amd.com
Cc: muli@il.ibm.com
LKML-Reference: <1257849980-22640-10-git-send-email-fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This changes detect_intel_iommu() to set intel_iommu_init() to
iommu_init hook if detect_intel_iommu() finds the IOMMU.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: chrisw@sous-sol.org
Cc: dwmw2@infradead.org
Cc: joerg.roedel@amd.com
Cc: muli@il.ibm.com
LKML-Reference: <1257849980-22640-6-git-send-email-fujita.tomonori@lab.ntt.co.jp>
[ -v2: build fix for the !CONFIG_DMAR case ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Chris Wright has some patches which let us fall back to swiotlb nicely
if IOMMU initialisation fails. But those are a bit much for 2.6.32.
Instead, let's shift the check for the biggest problem, the HP and Acer
BIOS bug which reports a DMAR at physical address zero. That one can
actually be checked much earlier -- before we even admit to having
detected an IOMMU in the first place. So the swiotlb init goes ahead as
we want.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
SPIN_LOCK_UNLOCKED is deprecated. Use DEFINE_SPINLOCK instead.
Make the lock static while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If firmware doesn't grant over native hotplug control through ACPI
_OSC method, we must not evaluate OSHP.
Acked-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In case of AMD CPU northbridge functions this NUMA information might
differ. Here is an example from a 4-socket system.
Currently Linux shows
root@hagen:/sys/devices/pci0000:00/0000:00:1a.4# cat numa_node
0
root@hagen:/sys/devices/pci0000:00/0000:00:1a.4# cat local_cpu*
0-3
00000000,0000000f
which is not correct for northbridge functions as the local CPUs
are those of the same socket.
With this patch and a quirk for AMD CPU NB functions Linux can
do better and correctly show
root@hagen:/sys/devices/pci0000:00/0000:00:1a.4# cat numa_node
2
root@hagen:/sys/devices/pci0000:00/0000:00:1a.4# cat local_cpu*
8-11
00000000,00000f00
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix the following BUG_ON() problem reported by Alex Chiang.
This problem happened when removing PCIe root port using PCI logical
hotplug operation.
The immediate cause of this problem is that the pointer to invalid
data structure is passed to pcie_update_aspm_capable() by
pcie_aspm_exit_link_state(). When pcie_aspm_exit_link_state() received
a pointer to root port link, it unconfigures the root port link and
frees its data structure at first. At this point, there are not links
to configure under the root port and the data structure for root port
link is already freed. So pcie_aspm_exit_link_state() must not call
pcie_update_aspm_capable() and pcie_config_aspm_path().
This patch fixes the problem by changing pcie_aspm_exit_link_state()
not to call pcie_update_aspm_capable() and pcie_config_aspm_path() if
the specified link is root port link.
------------[ cut here ]------------
kernel BUG at drivers/pci/pcie/aspm.c:606!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
last sysfs file: /sys/devices/pci0000:40/0000:40:13.0/remove
CPU 1
Modules linked in: shpchp
Pid: 9345, comm: sysfsd Not tainted 2.6.32-rc5 #98 ProLiant DL785 G6
RIP: 0010:[<ffffffff811df69b>] [<ffffffff811df69b>] pcie_update_aspm_capable+0x15/0xbe
RSP: 0018:ffff88082a2f5ca0 EFLAGS: 00010202
RAX: 0000000000000e77 RBX: ffff88182cc3e000 RCX: ffff88082a33d006
RDX: 0000000000000001 RSI: ffffffff811dff4a RDI: ffff88182cc3e000
RBP: ffff88082a2f5cc0 R08: ffff88182cc3e000 R09: 0000000000000000
R10: ffff88182fc00180 R11: ffff88182fc00198 R12: ffff88182cc3e000
R13: 0000000000000000 R14: ffff88182cc3e000 R15: ffff88082a2f5e20
FS: 00007f259a64b6f0(0000) GS:ffff880864600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 00007feb53f73da0 CR3: 000000102cc94000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process sysfsd (pid: 9345, threadinfo ffff88082a2f4000, task ffff88082a33cf00)
Stack:
ffff88182cc3e000 ffff88182cc3e000 0000000000000000 ffff88082a33cf00
<0> ffff88082a2f5cf0 ffffffff811dff52 ffff88082a2f5cf0 ffff88082c525168
<0> ffff88402c9fd2f8 ffff88402c9fd2f8 ffff88082a2f5d20 ffffffff811d7db2
Call Trace:
[<ffffffff811dff52>] pcie_aspm_exit_link_state+0xf5/0x11e
[<ffffffff811d7db2>] pci_stop_bus_device+0x76/0x7e
[<ffffffff811d7d67>] pci_stop_bus_device+0x2b/0x7e
[<ffffffff811d7e4f>] pci_remove_bus_device+0x15/0xb9
[<ffffffff811dcb8c>] remove_callback+0x29/0x3a
[<ffffffff81135aeb>] sysfs_schedule_callback_work+0x15/0x6d
[<ffffffff81072790>] worker_thread+0x19d/0x298
[<ffffffff8107273b>] ? worker_thread+0x148/0x298
[<ffffffff81135ad6>] ? sysfs_schedule_callback_work+0x0/0x6d
[<ffffffff810765c0>] ? autoremove_wake_function+0x0/0x38
[<ffffffff810725f3>] ? worker_thread+0x0/0x298
[<ffffffff8107629e>] kthread+0x7d/0x85
[<ffffffff8102eafa>] child_rip+0xa/0x20
[<ffffffff8102e4bc>] ? restore_args+0x0/0x30
[<ffffffff81076221>] ? kthread+0x0/0x85
[<ffffffff8102eaf0>] ? child_rip+0x0/0x20
Code: 89 e5 8a 50 48 31 c0 c0 ea 03 83 e2 07 e8 b2 de fe ff c9 48 98 c3 55 48 89 e5 41 56 49 89 fe 41 55 41 54 53 48 83 7f 10 00 74 04 <0f> 0b eb fe 48 8b 05 da 7d 63 00 4c 8d 60 e8 4c 89 e1 eb 24 4c
RIP [<ffffffff811df69b>] pcie_update_aspm_capable+0x15/0xbe
RSP <ffff88082a2f5ca0>
---[ end trace 6ae0f65bdeab8555 ]---
Reported-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There are a lot of codes that searches PCI express capability offset
in the PCI configuration space using pci_find_capability(). Caching it
in the struct pci_dev will reduce unncecessary search. This patch adds
an additional 'pcie_cap' fields into struct pci_dev, which is
initialized at pci device scan time (in set_pcie_port_type()).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This makes PCI resource management messages more consistent and adds a few
new messages to aid debugging.
Whenever we assign resources to a device, update a BAR, or change a
bridge aperture, it's worth noting it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since we have a struct device, we might as well use dev_printk. Note that
both pr_debug() and dev_dbg() are completely compiled out unless DEBUG or
DYNAMIC_DEBUG is defined.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Messages about PME# being supported and enabled/disabled are probably
useful for debug, but maybe don't need to be on the console.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 3b073eda has removed pci_find_slot, so there's no point in
mentioning it in the config description as one of the deprecated APIs
there are enabled by PCI_LEGACY and still used by some drivers.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Jesse accidentally applied v1 [1] of the patchset instead of v2 [2]. This
is the diff between v1 and v2.
The changes in this patch are:
- tidied vsprintf stack buffer to shrink and compute size more
accurately
- use %pR for decoding and %pr for "raw" (with type and flags) instead
of adding %pRt and %pRf
[1] http://lkml.org/lkml/2009/10/6/491
[2] http://lkml.org/lkml/2009/10/13/441
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
AMD 813x rev. B1 (like rev. B2) devices generate no interrupts if
quirk_disable_amd_813x_boot_interrupt is executed, add an exception.
http://bugzilla.kernel.org/show_bug.cgi?id=14159
Patch also adds missing cases for DECLARE_PCI_FIXUP_RESUME and
DECLARE_PCI_FIXUP_FINAL calls to quirk_disable_amd_813x_boot_interrupt.
Signed-off-by: Stefan Assmann <sassmann@redhat.com>
Tested-by: Gabriele Giorgetti <g.giorgetti@teamsystem.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Using list_for_each_entry instead of list_for_each allows us to
enhance readability and minorly reduce some stack usage.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch moves PCI I/O APIC support from acpiphp to a separate driver.
Like pciehp and shpchp, acpiphp handles PCI hotplug, i.e., addition and
removal of PCI adapters. But in addition, acpiphp handles some ACPI
hotplug, such as the addition of new host bridges, and the I/O APIC
support was tangled up with that.
I don't think the I/O APIC support needs to be in acpiphp; PCI I/O APICs
usually appear as a function on a PCI host bridge, and we'll enumerate the
APIC before any of the devices behind the bridge that use it.
As far as I know, nobody actually uses I/O APIC hotplug. It depends on
acpi_register_ioapic(), which is only implemented for ia64, and I don't
think any vendors have supported I/O chassis hotplug yet.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
CC: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
CC: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Replaced some error return values in aer_inject. Use -ENODEV when we
can't find a device and -ENOTTY when the device does not support PCIe AER.
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add support for PCI domains (segments) to aer_inject.
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Added the pci_get_domain_and_slot_function which is analogous to
pci_get_bus_and_slot. It returns a pci_dev given a domain (segment) number,
bus number, and devnr. Like pci_get_bus_and_slot,
pci_get_domain_bus_and_slot holds a reference to the returned pci_dev.
Converted pci_get_bus_and_slot to a wrapper that calls
pci_get_domain_bus_and_slot with the domain hard-coded to 0.
This routine was patterned off code suggested by Bjorn Helgaas.
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Change to populate the subsystem vendor and subsytem device IDs for
PCI-PCI bridges that implement the PCI Subsystem Vendor ID capability.
Previously bridges left subsystem vendor IDs unpopulated.
Signed-off-by: Gabe Black <gabe.black@ni.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Feedback from Hidetoshi Seto and Kenji Kaneshige incorporated. This
correctly handles PCI-X bridges, PCIe root ports and endpoints, and
prints debug messages when invalid/reserved types are found in the
HEST. PCI devices not in domain/segment 0 are not represented in
HEST, thus will be ignored.
Today, the PCIe Advanced Error Reporting (AER) driver attaches itself
to every PCIe root port for which BIOS reports it should, via ACPI
_OSC.
However, _OSC alone is insufficient for newer BIOSes. Part of ACPI
4.0 is the new APEI (ACPI Platform Error Interfaces) which is a way
for OS and BIOS to handshake over which errors for which components
each will handle. One table in ACPI 4.0 is the Hardware Error Source
Table (HEST), where BIOS can define that errors for certain PCIe
devices (or all devices), should be handled by BIOS ("Firmware First
mode"), rather than be handled by the OS.
Dell PowerEdge 11G server BIOS defines Firmware First mode in HEST, so
that it may manage such errors, log them to the System Event Log, and
possibly take other actions. The aer driver should honor this, and
not attach itself to devices noted as such.
Furthermore, Kenji Kaneshige reminded us to disallow changing the AER
registers when respecting Firmware First mode. Platform firmware is
expected to manage these, and if changes to them are allowed, it could
break that firmware's behavior.
The HEST parsing code may be replaced in the future by a more
feature-rich implementation. This patch provides the minimum needed
to prevent breakage until that implementation is available.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Prevent unnecessary power off at initialization time. If slot power
is already off, we don't need to power off the slot.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp returns successfully on read/write failure with dummy
state values. It should return error instead.
With this patch, pciehp no longer uses hotplug_slot_info data
structure. So this also removes hotplug_slot_info related code. But
note that it still allocates hotplug_slot_info because it is required
by pci hotplug core.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp driver creates 'attention' and 'latch' files even if
the controller doesn't support them. In this case, the contents of
those files are meaningless and unpredictable. Those files should be
created only if the controller has the corresponding capabilities.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove wrong workaround for BAD DLLP error, which confused surprise
down error with DLL errors.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp doesn't handle Data Link Layer State Changed Event
notification. So it needs to be disabled at initialization time,
otherwise other event notifications are not generated.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When probing for ROM BAR size, we should not change bits 1:10 in this
BAR, because these bits are marked as "reserved for future use" in PCI
spec, so changing them might have side effects.
No such issue for I/O or memory, as there is an implementation note in
PCI spec which explicitly allows writing 0xfffffffff there.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch is predicated on Jeremy's patch in include/xen/xen.h. It'll
prevent ACS init unless the platform has both an IOMMU and we're running
as dom0.
Signed-off-by: Allen Kay <allen.m.kay@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Note: dom0 checking in v4 has been separated out into 2/2.
This patch enables P2P upstream forwarding in ACS capable PCIe switches.
It solves two potential problems in virtualization environment where a PCIe
device is assigned to a guest domain using a HW iommu such as VT-d:
1) Unintentional failure caused by guest physical address programmed
into the device's DMA that happens to match the memory address range
of other downstream ports in the same PCIe switch. This causes the PCI
transaction to go to the matching downstream port instead of go to the
root complex to get translated by VT-d as it should be.
2) Malicious guest software intentionally attacks another downstream
PCIe device by programming the DMA address into the assigned device
that matches memory address range of the downstream PCIe port.
We are in process of implementing device filtering software in KVM/XEN
management software to allow device assignment of PCIe devices behind a PCIe
switch only if it has ACS capability and with the P2P upstream forwarding bits
enabled. This patch is intended to work for both KVM and Xen environments.
Signed-off-by: Allen Kay <allen.m.kay@intel.com>
Reviewed-by: Mathew Wilcox <willy@linux.intel.com>
Reviewed-by: Chris Wright <chris@sous-sol.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As a followup to 71a082efc9, it's conceivable
that some vendors may expose PCI hotplug functionality through both vendor
mechanisms and ACPI. The native mechanism will generally be a superset of
any functionality provided via ACPI, so the acpiphp driver should always
be initialised after any others. Change the link order such that acpiphp
will not be initialised until any other statically linked drivers have had
an opportunity to claim the hardware.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_dfl_cache_line_size is marked as __initdata but referenced by
pci_init() which is __devinit. Make it __devinitdata instead of
__initdata.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For non hotplug PCI devices, the system firmware usually configures
CLS correctly. For pccard devices system firmware can't do it and
Linux PCI layer doesn't do it either. Unfortunately this leads to
poor performance for certain devices (sata_sil). Unless MWI, which
requires separate configuration, is to be used, CLS doesn't affect
correctness, so the configuration should be harmless.
This patch makes pci_set_cacheline_size() always built and export it
and make pccard call it during attach.
Please note that some other PCI hotplug drivers (shpchp and pciehp)
also configure CLS on hotplug.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Greg KH <greg@kroah.com>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Axel Birndt <towerlexa@gmx.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
sparc64 is now the only user of PCI_CACHE_LINE_BYTES. Drop it and set
pci_dfl_cache_line_size from pcibios_init() instead and drop
PCI_CACHE_LINE_BYTES handling from generic pci code.
Orignally-From: David Miller <davem@davemloft.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Till now, CLS has been determined either by arch code or as
L1_CACHE_BYTES. Only x86 and ia64 set CLS explicitly and x86 doesn't
always get it right. On most configurations, the chance is that
firmware configures the correct value during boot.
This patch makes pci_init() determine CLS by looking at what firmware
has configured. It scans all devices and if all non-zero values
agree, the value is used. If none is configured or there is a
disagreement, pci_dfl_cache_line_size is used. arch can set the dfl
value (via PCI_CACHE_LINE_BYTES or pci_dfl_cache_line_size) or
override the actual one.
ia64, x86 and sparc64 updated to set the default cls instead of the
actual one.
While at it, declare pci_cache_line_size and pci_dfl_cache_line_size
in pci.h and drop private declarations from arch code.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Miller <davem@davemloft.net>
Acked-by: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This reverts commit 308cf8e13f. This
patch had trouble with transparent bridges, among other things. A more
readable and correct version should land in 2.6.33.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit d43c36dc6b ("headers: remove
sched.h from interrupt.h") left some build errors in some configurations
due to drivers having depended on getting header files "accidentally".
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[ Combined several one-liners from Ingo into one single patch - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/~dwmw2/iommu-2.6.32:
x86: Move pci_iommu_init to rootfs_initcall()
Run pci_apply_final_quirks() sooner.
Mark pci_apply_final_quirks() __init rather than __devinit
Rename pci_init() to pci_apply_final_quirks(), move it to quirks.c
intel-iommu: Yet another BIOS workaround: Isoch DMAR unit with no TLB space
intel-iommu: Decode (and ignore) RHSA entries
intel-iommu: Make "Unknown DMAR structure" message more informative
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: Prevent AER driver from being loaded on non-root port PCIE devices
PCI: get larger bridge ranges when space is available
PCI: pci.c: fix kernel-doc notation
PCI quirk: TI XIO200a erroneously reports support for fast b2b transfers
PCI PM: Read device power state from register after updating it
PCI: remove pci_assign_resource_fixed()
PCI: PCIe portdrv: remove "-driver" from driver name
Having this as a device_initcall() means that some real device drivers
can actually initialise _before_ the quirks are run, which is wrong.
We want it to run _before_ device_initcall(), but _after_ fs_initcall(),
since some arch-specific PCI initialisation like pcibios_assign_resources()
is done at fs_initcall().
We could use rootfs_initcall() but I actually want to use that for the
IOMMU initialisation, which has to come after the quirks, but still
before the real devices. So use fs_initcall_sync() instead -- since this
is entirely synchronous, it doesn't hurt that it'll escape the
synchronisation.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This function may have done more in the past, but all it does now is
apply the PCI_FIXUP_FINAL quirks. So name it sensibly and put it where
it belongs.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
A bug was seen on boards using a PLX 8518 switch device which advertises
AER on each of it's transparent bridges. The AER driver was loaded for
each bridge and this driver tried to access the AER source ID register
whenever an interrupt occured on the shared PCI INTX lines. The source
ID register does not exist on non root port PCIE device's which
advertise AER and trying to access this register causes a unsupported
request error on the bridge. Thus, when the next interrupt occurs,
another error is found and the non existent source ID register is
accessed again, and so it goes on.
The result is a spammed dmesg with unsupported request PCI express
errors on the bridge device that the AER driver is loaded against.
Reported-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Found one system:
[ 71.120590] pci 0000:40:05.0: scanning behind bridge, config 4f4a40, pass 0
[ 71.138283] PCI: Scanning bus 0000:4a
[ 71.140341] pci 0000:4a:00.0: found [15b3:6278] class 000c06 header type 00
[ 71.157173] pci 0000:4a:00.0: reg 10 64bit mmio: [0x000000-0x0fffff]
[ 71.161697] pci 0000:4a:00.0: reg 18 64bit mmio pref: [0x000000-0x7fffff]
[ 71.179403] pci 0000:4a:00.0: reg 20 64bit mmio pref: [0x000000-0xfffffff]
[ 71.185366] pci 0000:4a:00.0: calling quirk_resource_alignment+0x0/0x1dd
[ 71.200846] pci 0000:4a:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 71.219623] PCI: Fixups for bus 0000:4a
[ 71.222194] pci 0000:40:05.0: bridge 32bit mmio: [0xcf000000-0xcf0fffff]
[ 71.238662] pci 0000:40:05.0: bridge 64bit mmio pref: [0xcd800000-0xcdffffff]
[ 71.255793] PCI: Bus scan for 0000:4a returning with max=4a
Device needs a big pref mmio, but BIOS doesn't allocate mmio to it aside
from a small MMIO range. Later, the kernel will not allocate resources to
that to the device:
[ 99.574030] pci 0000:4a:00.0: BAR 4: can't allocate mem resource [0xd0000000-0xcdffffff]
[ 99.580102] pci 0000:4a:00.0: BAR 2: got res [0xcd800000-0xcdffffff] bus [0xcd800000-0xcdffffff] flags 0x12120c
[ 99.602307] pci 0000:4a:00.0: BAR 2: moved to bus [0xcd800000-0xcdffffff] flags 0x12120c
[ 99.615991] pci 0000:4a:00.0: BAR 0: got res [0xcf000000-0xcf0fffff] bus [0xcf000000-0xcf0fffff] flags 0x120204
[ 99.634499] pci 0000:4a:00.0: BAR 0: moved to bus [0xcf000000-0xcf0fffff] flags 0x120204
[ 99.654318] pci 0000:40:05.0: PCI bridge, secondary bus 0000:4a
[ 99.658766] pci 0000:40:05.0: IO window: disabled
[ 99.675478] pci 0000:40:05.0: MEM window: 0xcf000000-0xcf0fffff
[ 99.681663] pci 0000:40:05.0: PREFETCH window: 0x000000cd800000-0x000000cdffffff
So try to get a big range in the pci bridge if there is no child using
that range. With the patch we get:
[ 99.104525] pci 0000:4a:00.0: BAR 4: got res [0xfc080000000-0xfc08fffffff] bus [0xfc080000000-0xfc08fffffff] flags 0x12120c
[ 99.123624] pci 0000:4a:00.0: BAR 4: moved to bus [0xfc080000000-0xfc08fffffff] flags 0x12120c
[ 99.131977] pci 0000:4a:00.0: BAR 2: got res [0xfc090000000-0xfc0907fffff] bus [0xfc090000000-0xfc0907fffff] flags 0x12120c
[ 99.149788] pci 0000:4a:00.0: BAR 2: moved to bus [0xfc090000000-0xfc0907fffff] flags 0x12120c
[ 99.169248] pci 0000:4a:00.0: BAR 0: got res [0xc0200000-0xc02fffff] bus [0xc0200000-0xc02fffff] flags 0x120204
[ 99.189508] pci 0000:4a:00.0: BAR 0: moved to bus [0xc0200000-0xc02fffff] flags 0x120204
[ 99.206402] pci 0000:40:05.0: PCI bridge, secondary bus 0000:4a
[ 99.210637] pci 0000:40:05.0: IO window: disabled
[ 99.224856] pci 0000:40:05.0: MEM window: 0xc0200000-0xc03fffff
[ 99.230019] pci 0000:40:05.0: PREFETCH window: 0x000fc080000000-0x000fc097ffffff
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This quirk will disable fast back to back transfer on the secondary bus
segment of the TI Bridge.
Signed-off-by: Gabe Black <gabe.black@ni.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After attempting to change the power state of a PCI device
pci_raw_set_power_state() doesn't check if the value it wrote into
the device's PCI_PM_CTRL register has been stored in there, but
unconditionally modifies the device's current_state field to reflect
the change. This may cause problems to happen if the power state of
the device hasn't been changed in fact, because it will make the PCI
PM core make a wrong assumption.
To prevent such situations from happening modify
pci_raw_set_power_state() so that it reads the device's PCI_PM_CTRL
register after writing into it and uses the value read from the
register to update the device's current_state field. Also make it
print a message saying that the device refused to change its power
state as requested (returning an error code in such cases would cause
suspend regressions to appear on some systems, where device drivers'
suspend routines return error codes if pci_set_power_state() fails).
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Adrian commented out this function in 2baad5f96b, but I don't think
it's even worth cluttering the file with the unused code.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No need to include "-driver" in the driver name.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Tom Long Nguyen <tom.l.nguyen@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Allocate dma-remapping structures using numa locality info. On platforms
having remapping hardware units span different nodes, this enables
optimized dma-remapping transalation structures access by remapping hardware.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Allocate intr-remapping table using numa locality info. On platforms
having remapping hardware units span different nodes, this enables
optimized intr-remapping table entry access by remapping hardware.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for parsing Remapping Hardware Static Affinity (RHSA) structure.
This enables identifying the association between remapping hardware units and
the corresponding proximity domain. This enables to allocate transalation
structures closer to the remapping hardware unit.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Asus decided to ship a BIOS which configures sound DMA to go via the
dedicated IOMMU unit, but assigns precisely zero TLB entries to that
unit. Which causes the whole thing to deadlock, including the DMA
traffic on the _other_ IOMMU units. Nice one.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit 15b8dd53f5 changed info->hardware_id from a static array to
a pointer. If hardware_id is non-NULL, it points to a NULL-terminated
string, so we don't need to terminate it explicitly. However, it may
be NULL; in that case, we *can't* add a NULL terminator.
This causes a NULL pointer dereference oops for devices without _HID.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Lin Ming <ming.m.lin@intel.com>
CC: Bob Moore <robert.moore@intel.com>
CC: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
I recently got a system where the DMAR table included a couple of RHSA
(remapping hardware static affinity) entries. Rather than printing a
message about an "Unknown DMAR structure," it would probably be more
useful to dump the RHSA structure (as other DMAR structures are dumped).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We might as well print the type of the DMAR structure we don't know how
to handle when skipping it. Then someone getting this message has a
chance of telling whether the structure is just bogus, or if there
really is something valid that the kernel doesn't know how to handle.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/iommu-2.6: (23 commits)
intel-iommu: Disable PMRs after we enable translation, not before
intel-iommu: Kill DMAR_BROKEN_GFX_WA option.
intel-iommu: Fix integer wrap on 32 bit kernels
intel-iommu: Fix integer overflow in dma_pte_{clear_range,free_pagetable}()
intel-iommu: Limit DOMAIN_MAX_PFN to fit in an 'unsigned long'
intel-iommu: Fix kernel hang if interrupt remapping disabled in BIOS
intel-iommu: Disallow interrupt remapping if not all ioapics covered
intel-iommu: include linux/dmi.h to use dmi_ routines
pci/dmar: correct off-by-one error in dmar_fault()
intel-iommu: Cope with yet another BIOS screwup causing crashes
intel-iommu: iommu init error path bug fixes
intel-iommu: Mark functions with __init
USB: Work around BIOS bugs by quiescing USB controllers earlier
ia64: IOMMU passthrough mode shouldn't trigger swiotlb init
intel-iommu: make domain_add_dev_info() call domain_context_mapping()
intel-iommu: Unify hardware and software passthrough support
intel-iommu: Cope with broken HP DC7900 BIOS
iommu=pt is a valid early param
intel-iommu: double kfree()
intel-iommu: Kill pointless intel_unmap_single() function
...
Fixed up trivial include lines conflict in drivers/pci/intel-iommu.c
The following 64 bit promotions are necessary to handle memory above the
4GiB boundary correctly.
[dwmw2: Fix the second part not to need 64-bit arithmetic at all]
Signed-off-by: Benjamin LaHaise <ben.lahaise@neterion.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If end_pfn is equal to (unsigned long)-1, then the loop will never end.
Seen on 32-bit kernel, but could have happened on 64-bit too once we get
hardware that supports 64-bit guest addresses.
Change both functions to a 'do {} while' loop with the test at the end,
and check for the PFN having wrapper round to zero.
Reported-by: Benjamin LaHaise <ben.lahaise@neterion.com>
Tested-by: Benjamin LaHaise <ben.lahaise@neterion.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Sheng Yang