There is no big difference at implementation for .suspend/.resume
between DAI driver and Component driver.
But because some driver is using DAI version, thus ALSA SoC needs
to keep supporting it, hence, framework becoming verbose.
If we can switch all DAI driver .suspend/.resume to Component driver,
we can remove verbose code from ALSA SoC.
Driver is getting its private data via dai->dev.
But dai->dev and component->dev are same dev, thus, we can convert
these. For same reason, we can convert dai->active to
component->active if necessary.
This patch moves DAI driver .suspend/.resume to Component driver
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87blqzym4w.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC PCM core deals the empty ioctl field now as default.
Let's kill the redundant lines.
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20191210145406.21419-5-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-50-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190727150738.54764-10-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes below issues reported by coccicheck
sound/soc/bcm/cygnus-pcm.c:642:5-8: Unneeded variable: "ret". Return "0"
on line 650
sound/soc/bcm/cygnus-pcm.c:671:5-8: Unneeded variable: "ret". Return "0"
on line 696
We cannot change return type of these functions as they are callback
functions of snd_pcm_ops
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Link: https://lore.kernel.org/r/20190709184236.GA7873@hari-Inspiron-1545
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now we have devm_snd_soc_register_component().
Let's use it instead of snd_soc_register_component().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Note:
- The various SND_SOC_LPASS_* symbols had to loose their dependencies
on HAS_DMA, as they are selected by SND_SOC_STORM and/or
SND_SOC_APQ8016_SBC.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pointer res is being initialized with a value that is never read
and re-assigned immediately after, hence the initialization is redundant
and can be removed.
Cleans up clang warning:
sound/soc/bcm/cygnus-ssp.c:1284:19: warning: Value stored to 'res'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If bcm2835 is configured as bitclock master calling hw_params()
after prepare() fails with EBUSY. This also makes it impossible to
use bcm2835 in full duplex mode.
The error is caused by the split clock setup: clk_set_rate
is called in hw_params, clk_prepare_enable in prepare. As hw_params
doesn't check if the clock was already enabled clk_set_rate
fails with EBUSY.
Fix this by moving clock startup from prepare to hw_params and
let hw_params properly deal with an already set up or enabled
clock.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP modes and left/right justified modes can be supported
on bcm2835 by configuring the frame sync polarity and
frame sync length registers and by adjusting the
channel data position registers.
Clock and frame sync polarity handling in hw_params has
been refactored to make the interaction between logical
rising/falling edge frame start and physical configuration
(changed by normal/inverted polarity modes) clearer.
Modes where the first active data bit is transmitted immediately
after frame start (eg DSP mode B with slot 0 active)
only work reliable if bcm2835 is configured as frame master.
In frame slave mode channel swap (or shift, this isn't quite
clear yet) can occur.
Currently the driver only warns if an unstable configuration
is detected but doensn't prevent using them.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
bcm2835's configuration registers can't be changed when a stream
is running, which means asymmetric configurations aren't supported.
Channel and rate symmetry are already enforced by constraints
but samplebits had been missed.
As hw_params doesn't check for symmetry constraints by itself
and just returns success if a stream is running this led to
situations where asymmetric configurations were seeming to
succeed but of course didn't work because the hardware wasn't
configured at all.
Fix this by adding the missing samplerate symmetry constraint.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sample rates are only restricted by the capabilities of the
clock driver, so use SNDRV_PCM_RATE_CONTINUOUS instead of
SNDRV_PCM_RATE_8000_192000.
Tests (eg with pcm5122) have shown that bcm2835 works fine
in 384kHz/32bit stereo mode, so change the maximum allowed
rate from 192kHz to 384kHz.
Signed-off-by: Matthias Reichl <hias@horus.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
bcm2835 supports arbitrary positioning of channel data within
a frame and thus is capable of supporting TDM modes. Since
the driver is limited to 2-channel operations only TDM setups
with exactly 2 active slots are supported.
Logical TDM slot numbering follows the usual convention:
For I2S-like modes, with a 50% duty-cycle frame clock,
slots 0, 2, ... are transmitted in the first half of a frame,
slots 1, 3, ... are transmitted in the second half.
For DSP modes slot numbering is ascending: 0, 1, 2, 3, ...
Channel position calculation has been refactored to use
TDM info and moved out of hw_params.
set_tdm_slot, set_bclk_ratio and hw_params now check more
strictly if the configuration is valid. Illegal configurations
like odd number of slots in I2S mode, data lengths exceeding
slot width or frame sizes larger than the hardware limit of
1024 are rejected. Also hw_params now properly checks for
errors from clk_set_rate.
Allowed PCM formats are already guarded by stream constraints,
thus the formats check in hw_params has been removed and
data_length is now retrieved via params_width().
Also standard functions like snd_soc_params_to_bclk are now
being used instead of manual calculations to make the code
more readable.
Special care has been taken to ensure that set_bclk_ratio works
as before. The bclk ratio is mapped to a 2-channel TDM config
with a slot width of half the ratio. In order to support odd ratios,
which can't be expressed via a TDM config, the ratio (frame length)
is stored and used by hw_params.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Variable active_slots is unsigned so checking whether it is less than
zero is not necessary.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These modes of operation were not working properly and it is
unclear if the hardware could fully support these modes properly.
There is little to be gained by enabling these modes, therefore,
we will just remove support.
Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPDIF port cannot modify its format so a set_fmt function is not
needed. Previously, we used a generic set_fmt for all ports and returned
an error code for the SPDIF port. It is cleaner to not populate the
set_fmt field.
Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The helper function cygnus_ssp_set_custom_fsync_width() is intended
to be called from an ASoC machine driver, need to export symbol
if using modules.
Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make this const as it is only used during a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
add depends on HAS_DMA to Kconfig. This fixes error reported
by kbuild test robot when building for ARCH=m32r:
ERROR: "bad_dma_ops" [sound/soc/bcm/snd-soc-cygnus.ko] undefined!
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Cygnus audio DMA driver. It supports playback
and capture modes and uses ringbuffers for data transfer.
Signed-off-by: Lori Hikichi <lhikichi@broadcom.com>
Signed-off-by: Simran Rai <ssimran@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Arun Parameswaran <arunp@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Cygnus audio DAI driver. It supports I2S, TDM
and SPDIF modes and uses three clocks derived from PLL.
This patchset has been tested on Cygnus wireless audio
bcm958305K board.
Signed-off-by: Lori Hikichi <lhikichi@broadcom.com>
Signed-off-by: Simran Rai <ssimran@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Arun Parameswaran <arunp@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bcm2835-i2s driver already has support for the S16_LE format but
that format hasn't been made available because dmaengine_pcm didn't
support packed data transfers.
bcm2835-i2s needs 16-bit left+right channel data to be packed into
a 32-bit word, the FIFO register is 32-bit only and doesn't support
16-bit access.
Now that dmaengine_pcm supports packed transfers the format can
be made available by setting the SND_DMAENGINE_PCM_DAI_FLAG_PACK flag.
No further configuration is necessary:
- snd_dmaengine_dai_dma_data.addr_width is already set to
DMA_SLAVE_BUSWIDTH_4_BYTES to force 32-bit DMA transfers
- dmaengine_pcm will pick up the S16_LE format from the DAI
configuration and make it available since it's no longer
masked out due to the PACK flag.
- there are no further corner cases to catch in hw_params,
since the channel count is fixed at 2 we always have two
16-bit stereo samples that can be transferred via 32-bit DMA
Signed-off-by: Matthias Reichl <hias@horus.com>
Tested-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We only need to enable the clock if we are a clock master.
Code ported from bcm2708-i2s driver in Raspberry Pi tree.
Original work by Zoltan Szenczi.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds 24 bit support to the I2S driver of the BCM2835
Code ported from bcm2708-i2s driver in Raspberry Pi tree.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the move to the new clock framework with commit 94cb7f76ca
("ARM: bcm2835: Switch to using the new clock driver support.")
this driver was no longer functional as it was manipulating the
clock registers locally without going true the framework.
This patch moves to use the new clock framework and also
moves away from the hardcoded address offsets for DMA getting
the dma-address directly from the device tree.
Note that the optimal bclk_ratio selection to avoid jitter
due to the use of fractional dividers, which is in the
current version has been removed, because not all devices
support these non power of 2 sized transfers, which resulted
in lots of (downstream) modules that use:
snd_soc_dai_set_bclk_ratio(cpu_dai, sample_bits * 2);
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cleanup of includes so that they are ordered alphabetically.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
These platform drivers have a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CONFIG_SND_SOC_DMAENGINE_PCM was renamed to CONFIG_SND_DMAENGINE_PCM
recently. And yet we don't have to select it since
CONFIG_SND_GENERIC_DMAENGINE_PCM selects the dependency by itself, so
just rip it off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver adds support for digital audio (I2S)
for the BCM2835 SoC that is used by the
Raspberry Pi. External audio codecs can be
connected to the Raspberry Pi via P5 header.
It relies on cyclic DMA engine support for BCM2835.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Kuninori Morimoto