When attaching a pollfunc iio_trigger_attach_poll_func will allocate a
virtual irq and call the driver's set_trigger_state function. Fix error
handling to undo previous steps if any fails.
In particular this fixes handling errors from a driver's
set_trigger_state function. When using triggered buffers a failure to
enable the trigger used to make the buffer unusable.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes odd behavior after reboot.
The fact that we set the device to powerdown mode is not sufficient to
prevent DRDY being active because we might still have an unread sample.
Even if powerdown was sufficient keeping DRDY disabled while trigger is
not active is a good idea.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes a possible race where an interrupt arrives before complete
initialization and crashes because iio_trigger_get_drvdata returns NULL.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
commit 98ad8b41f58dff6b30713d7f09ae3834b8df7ded
("iio: st_sensors: verify interrupt event to status") caused
a regression when reading ST sensors from a HRTimer trigger
rather than the intrinsic interrupts: the HRTimer may
trigger faster than the sensor provides new values, and
as the check against new values available as a cause of
the interrupt trigger was done in the poll function,
this would bail out of the HRTimer interrupt with
IRQ_NONE.
So clearly we need to only check the new values available
from the proper interrupt handler and not from the poll
function, which should rather just read the raw values
from the registers, put them into the buffer and be happy.
To achieve this: switch the ST Sensors over to using a true
threaded interrupt handler.
In the interrupt thread, check if new values are available,
else yield to the (potential) next device on the same
interrupt line to check the registers. If the interrupt
was ours, proceed to poll the values.
Instead of relying on iio_trigger_generic_data_rdy_poll() as
a top half to wake up the thread that polls the sensor for
new data, have the thread call iio_trigger_poll_chained()
after determining that is is the proper source of the
interrupt. This is modelled on drivers/iio/accel/mma8452.c
which is already using a properly threaded interrupt handler.
In order to get the same precision in timestamps as
previously, where samples would be timestamped in the
poll function pf->timestamp when calling
iio_trigger_generic_data_rdy_poll() we introduce a
local timestamp in the sensor data, set it in the top half
(fastpath) of the interrupt handler and provide that to the
core when calling iio_push_to_buffers_with_timestamp().
Additionally: if the active scanmask is not set for the
sensor no IRQs should be enabled and we need to bail out
with IRQ_NONE. This can happen if spurious IRQs fire when
installing the threaded interrupt handler.
Tested with hard interrupt triggers on LIS331DL, then also
tested with hrtimers on the same sensor by creating a 75Hz
HRTimer and using it to poll the sensor.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Reported-by: Crestez Dan Leonard <cdleonard@gmail.com>
Tested-by: Crestez Dan Leonard <cdleonard@gmail.com>
Tested-by: Jonathan Cameron <jic23@kernel.org>
Fixes: 97865fe413 ("iio: st_sensors: verify interrupt event to status")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
MODULE_ALIAS isn't needed since the module name is the same as the alias
defined.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
bmc150 driver supports also BMC156 and BMM150 chips.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Using the struct i2c_device->id field for naming the light sensor
is a bad idea: when booting from the pure device tree this is NULL
and that causes the device not to have the "name" property in
sysfs and that in turn confuses the "lsiio" command to stop listing
devices.
So instead of using the device .id, use the hard string "bh1780",
which works just fine.
Fixes: 1f0477f183 ("iio: light: new driver for the ROHM BH1780")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The code in runtime_[suspend|resume] was assuming that the
i2c client data was the bh1780 state container, but it contains
the IIO device. So first dereference the IIO device from the
i2c client, then get the state container using the iio_priv()
call.
Fixes: 1f0477f183 ("iio: light: new driver for the ROHM BH1780")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
IIO_TEMP channel was being incorrectly reported back as Celsius when it
should have been milliCelsius. This is via an incorrect scale value being
returned to userspace.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Driver was checking for direct mode but not locking it down.
Use iio_device_claim_direct_mode() to guarantee device stays
in direct mode.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Ensure failure to enable power regulators is properly handled.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use SMBus "block read" protocol only when supported by adapter.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Remove st_sensors_get_buffer_element symbol export since not explicitly
used outside of st_sensors driver.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Temperature channels report scaled samples in Celsius although expected as
milli degree Celsius in Documentation/ABI/testing/sysfs-bus-iio.
Gains are not implemented at all for LPS001WP pressure and temperature
channels.
This patch ensures that proper offsets and scales are exposed to userpace
for both pressure and temperature channels.
Also fix a NULL pointer exception when userspace reads content of sysfs
scale attribute when gains are not defined.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Initial support for ST LPS22HB pressure sensor. Datasheet:
http://www2.st.com/resource/en/datasheet/lps22hb.pdf
Features:
* pressure data and timestamping channels
* sampling frequency selection
* interrupt based trigger
* over I2C or SPI
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This structure has not been optional for a long time (if ever) but the
code implies that it is. As we then use it later in a fashion that would
crash if it was in fact NULL, it's inconsistent so fix it up by removing
unnecessary checks.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add datasheet names for ADC channels to allow iio consumers access.
Signed-off-by: Matt Ranostay <matt.ranostay@intel.com>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Buffer wasn't of a valid size to allow the timestamp, and correct padding.
This patchset also moves the buffer off the stack, and onto the heap.
Cc: george.mccollister@gmail.com
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Triggered buffers shouldn't return processed data, and the respective
conversion was overflowing the defined .realbits for the channel.
Cc: george.mccollister@gmail.com
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
IIO_CHAN_INFO_RAW was returning processed data which was incorrect.
This also adds the IIO_CHAN_INFO_SCALE value to convert to a processed value.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Enable humidity support for the BME280 part
Signed-off-by: Matt Ranostay <matt.ranostay@intel.com>
Acked-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is not implemented and doesn't really make sense because IIO
proximity is unit-less.
Remove IIO_CHAN_INFO_SCALE from info_mask because so that the _scale
sysfs entry won't appear. This fixes userspace tools like generic_buffer
which abort when reads returns an error.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This driver does not call i2c_smbus_read|write_byte_data(),
so remove the corresponding functionality test. It uses regmap
to handle byte transfers transparently.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Reviewed-by:Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Matt Ranostay <matt.ranostay@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Nuvoton NAU7802 ADC is able to adjust its gain but prior knowledge of
its possible values was required to adjust it. Users had to guess the
possible gain values based on the ADC datasheet or on this driver's code.
This exposes the possible values in the in_voltage_scale_available file of
each nau7802 ADC device. The gain is set for the whole ADC and is therefore
not configurable by channel. Thus, there exists only one
in_voltage_scale_available file for each nau7802 ADC device even if it has
two separate channels.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The I2C drivers have an i2c_device_id array but that information isn't
exported to the modules using the MODULE_DEVICE_TABLE() macro. So the
modules autoloading won't work if the I2C device is registered using
OF or legacy board files due missing alias information in the modules.
The issue was found using Kieran Bingham's coccinelle semantic patch:
https://lkml.org/lkml/2016/5/10/520
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
TI ADS1115 is a 16-bit resolution ADC that is register map
compatible with the ADS1015 device.
Signed-off-by: Matt Ranostay <matt.ranostay@intel.com>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Acked-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We haven't taken the lock yet so we don't need to unlock here.
Fixes: 0d96d5ead3 ('iio: humidity: Add triggered buffer support for AM2315')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
BMM150 is register compatible with magnetometer part of
BMC156.
Datasheet is at:
http://www.mouser.com/ds/2/783/BST-BMM150-DS001-01-786480.pdf
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Apply the correct mask to enable all available humidity integration
times. Currently, the driver defaults to 6500 and all is okay with that.
However, if 3850 is selected we get a stuck bit and can't change back
to 6500 or select 2500. (Verified with HDC1008)
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Matt Ranostay <mranostay@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Here's the big staging and iio driver update for 4.7-rc1.
I think we almost broke even with this release, only adding a few more
lines than we removed, which isn't bad overall given that there's a
bunch of new iio drivers added. The Lustre developers seem to have
woken up from their sleep and have been doing a great job in cleaning up
the code and pruning unused or old cruft, the filesystem is almost
readable :)
Other than that, just a lot of basic coding style cleanups in the churn.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/00QACgkQMUfUDdst+ynXYQCdG9oEsw4CCItbjGfQau5YVGbd
TOcAnA19tZz+Wcg3sLT8Zsm979dgVvDt
=9UG/
-----END PGP SIGNATURE-----
Merge tag 'staging-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver updates from Greg KH:
"Here's the big staging and iio driver update for 4.7-rc1.
I think we almost broke even with this release, only adding a few more
lines than we removed, which isn't bad overall given that there's a
bunch of new iio drivers added.
The Lustre developers seem to have woken up from their sleep and have
been doing a great job in cleaning up the code and pruning unused or
old cruft, the filesystem is almost readable :)
Other than that, just a lot of basic coding style cleanups in the
churn. All have been in linux-next for a while with no reported
issues"
* tag 'staging-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (938 commits)
Staging: emxx_udc: emxx_udc: fixed coding style issue
staging/gdm724x: fix "alignment should match open parenthesis" issues
staging/gdm724x: Fix avoid CamelCase
staging: unisys: rename misleading var ii with frag
staging: unisys: visorhba: switch success handling to error handling
staging: unisys: visorhba: main path needs to flow down the left margin
staging: unisys: visorinput: handle_locking_key() simplifications
staging: unisys: visorhba: fail gracefully for thread creation failures
staging: unisys: visornic: comment restructuring and removing bad diction
staging: unisys: fix format string %Lx to %llx for u64
staging: unisys: remove unused struct members
staging: unisys: visorchannel: correct variable misspelling
staging: unisys: visorhba: replace functionlike macro with function
staging: dgnc: Need to check for NULL of ch
staging: dgnc: remove redundant condition check
staging: dgnc: fix 'line over 80 characters'
staging: dgnc: clean up the dgnc_get_modem_info()
staging: lustre: lnet: enable configuration per NI interface
staging: lustre: o2iblnd: properly set ibr_why
staging: lustre: o2iblnd: remove last of kiblnd_tunables_fini
...
Here's the "big" driver core update for 4.7-rc1.
Mostly just debugfs changes, the long-known and messy races with removing
debugfs files should be fixed thanks to the great work of Nicolai Stange. We
also have some isa updates in here (the x86 maintainers told me to take it
through this tree), a new warning when we run out of dynamic char major
numbers, and a few other assorted changes, details in the shortlog.
All have been in linux-next for some time with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0mwACgkQMUfUDdst+ynjXACgjNxR5nMUiM8ZuuD0i4Xj7VXd
hnIAoM08+XDCv41noGdAcKv+2WZVZWMC
=i+0H
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the "big" driver core update for 4.7-rc1.
Mostly just debugfs changes, the long-known and messy races with
removing debugfs files should be fixed thanks to the great work of
Nicolai Stange. We also have some isa updates in here (the x86
maintainers told me to take it through this tree), a new warning when
we run out of dynamic char major numbers, and a few other assorted
changes, details in the shortlog.
All have been in linux-next for some time with no reported issues"
* tag 'driver-core-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (32 commits)
Revert "base: dd: don't remove driver_data in -EPROBE_DEFER case"
gpio: ws16c48: Utilize the ISA bus driver
gpio: 104-idio-16: Utilize the ISA bus driver
gpio: 104-idi-48: Utilize the ISA bus driver
gpio: 104-dio-48e: Utilize the ISA bus driver
watchdog: ebc-c384_wdt: Utilize the ISA bus driver
iio: stx104: Utilize the module_isa_driver and max_num_isa_dev macros
iio: stx104: Add X86 dependency to STX104 Kconfig option
Documentation: Add ISA bus driver documentation
isa: Implement the max_num_isa_dev macro
isa: Implement the module_isa_driver macro
pnp: pnpbios: Add explicit X86_32 dependency to PNPBIOS
isa: Decouple X86_32 dependency from the ISA Kconfig option
driver-core: use 'dev' argument in dev_dbg_ratelimited stub
base: dd: don't remove driver_data in -EPROBE_DEFER case
kernfs: Move faulting copy_user operations outside of the mutex
devcoredump: add scatterlist support
debugfs: unproxify files created through debugfs_create_u32_array()
debugfs: unproxify files created through debugfs_create_blob()
debugfs: unproxify files created through debugfs_create_bool()
...
Pull i2c updates from Wolfram Sang:
- Peter Rosin did some major rework on the locking of i2c muxes by
seperating parent-locked muxes and mux-locked muxes.
This avoids deadlocks/workarounds when the mux itself needs i2c
commands for muxing. And as a side-effect, other workarounds in the
media layer could be eliminated. Also, Peter stepped up as the i2c
mux maintainer and will keep an eye on these changes.
- major updates to the octeon driver
- add a helper to the core to generate the address+rw_bit octal and
make drivers use it
- quite a bunch of driver updates
* 'i2c/for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (84 commits)
i2c: rcar: add DMA support
i2c: st: Implement bus clear
i2c: only check scl functions when using generic recovery
i2c: algo-bit: declare i2c_bit_quirk_no_clk_stretch as static
i2c: tegra: disable clock before returning error
[media] rtl2832: regmap is aware of lockdep, drop local locking hack
[media] rtl2832_sdr: get rid of empty regmap wrappers
[media] rtl2832: change the i2c gate to be mux-locked
[media] si2168: change the i2c gate to be mux-locked
iio: imu: inv_mpu6050: change the i2c gate to be mux-locked
i2c: mux: document i2c muxes and elaborate on parent-/mux-locked muxes
i2c: mux: relax locking of the top i2c adapter during mux-locked muxing
i2c: muxes always lock the parent adapter
i2c: allow adapter drivers to override the adapter locking
i2c: uniphier: add "\n" at the end of error log
i2c: mv64xxx: remove CONFIG_HAVE_CLK conditionals
i2c: mv64xxx: use clk_{prepare_enable,disable_unprepare}
i2c: mv64xxx: handle probe deferral for the clock
i2c: mv64xxx: enable the driver on ARCH_MVEBU
i2c: octeon: Add workaround for broken irqs on CN3860
...
The bmp280 driver also supports BMP180 which has a different chip id
with BMP280. The probe routine verifies that the device reports the
correct chip id but the error message is confusing as if BMP280's chip
id is always expected.
Reported-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Matt Ranostay <mranostay@gmail.com>
Cc: Vlad Dogaru <vlad.dogaru@intel.com>
Cc: Christoph Mair <christoph.mair@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This commit adds basic support for the Bosch Sensortec BMA220
digital triaxial acceleration sensor.
The device datasheet can be found here:
http://www.mouser.com/pdfdocs/BSTBMA220DS00308.PDF
Includes:
- raw readings
- ACPI detection
- power management
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Actually I2C_FUNC_SMBUS_WORD_DATA isn't need for this device, and regmap
handles all single byte reads transparently.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The root i2c adapter lock is then no longer held by the i2c mux during
accesses behind the i2c gate, and such accesses need to take that lock
just like any other ordinary i2c accesses do.
So, declare the i2c gate mux-locked, and zap the code that makes the
unlocked i2c accesses and just use ordinary regmap_write accesses.
This also happens to fix the deadlock described in
http://patchwork.ozlabs.org/patch/584776/ authored by
Adriana Reus <adriana.reus@intel.com> and submitted by
Daniel Baluta <daniel.baluta@intel.com>
----------8<----------
iio: imu: inv_mpu6050: Fix deadlock between i2c adapter lock and mpu lock
This deadlock occurs if the accel/gyro and the sensor on the auxiliary
I2C (in my setup it's an ak8975) are working at the same time.
Scenario:
T1 T2
==== ====
inv_mpu6050_read_fifo aux sensor op (eg. ak8975_read_raw)
| |
mutex_lock(&indio_dev->mlock) i2c_transfer
| |
i2c transaction i2c adapter lock
| |
i2c adapter lock i2c_mux_master_xfer
|
inv_mpu6050_select_bypass
|
mutex_lock(&indio_dev->mlock)
When we operate on an mpu sensor the order of locking is mpu lock
followed by the i2c adapter lock. However, when we operate the auxiliary
sensor the order of locking is the other way around.
...
----------8<----------
The reason this patch fixes the deadlock is that T2 does not grab the
i2c adapter lock until the very end (and grabs the newfangled i2c mux
lock where it previously grabbed the i2c adapter lock).
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Tested-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This adds the following sysfs files according to the iio ABI:
-rw-r--r-- 4096 in_accel_oversampling_ratio
-r--r--r-- 4096 in_accel_oversampling_ratio_available
Internally, the device knows about 4 different power modes that differ
in oversampling ratio (and power consumption). We just show the user
what oversampling ratio(s) is/are available, depending on the current
frequency.
The referenced table in the datasheets makes it easier to understand.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We register a new device type named "dummy", this will create a
configfs entry under:
* /config/iio/devices/dummy.
Creating dummy devices is now as simple as:
$ mkdir /config/iio/devices/dummy/my_dummy_device
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is similar with support for creating triggers via configfs.
Devices will be hosted under:
* /config/iio/devices
We allow users to register "device types" under:
* /config/iio/devices/<device_types>/
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
These definitions are not currently used and if the functionality
they represent is needed the values should be added back to a table
for easy userspace use.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The current channel number for the LEDs should match the stage
number that they are active during, fix this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently the TIA gain settings are exported to userspace as sysfs
entries that do not clearly represent their internal relation to the
sampling stages. The gain settings are enabled on a per-stage basis,
this can be seen in figure 24 of the current AFE4404 datasheet.
These gain settings should therefore be tied to the channels that are
read during these stages. Make this change here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
These drivers can use regmap fields to access fields in registers, this
allows us to remove some macros/defines and simplify code, do this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
These AFEs have 4 ADC mesuring stages (called LED2, ALED2, LED1, and
ALED1 in the datasheet), we map these as channels, these stages can serve
different purposes depending on the application. For instance the AFE4404
has an additional LED (LED3), this LED can be timed to be active during
stage 2 (or anystage, but the datasheet describes this case and the name
of the stage reflects this use). This ability is used further in upcoming
parts that tie the front-end gain and the LED timings together. For these
reasons we remove explicit naming the channels.
Without channel names it is best that the index numbers are in order to
match the stage number, reorder the channel numbers.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Input channel LED3 is only an alias for stage ALED2, this virtual channel
does nothing for us, remove this channel.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
No channel in the afe4403 driver has IIO_CHAN_INFO_OFFSET set so
remove the handlers for this.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The LED channels are not scannable and so scan_index should
be negative, fix this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Locking the two gain stages to the same setting adds no value for us,
so initialize them as unlocked and remove the sysfs for unlocking them.
This also allows us to greatly simplify showing and setting the gain
registers.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The drivers set some register values during initialization that can be
set at runtime, these defaults were used in testing but are not
necessary, remove these.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The drivers DT tables are not built-in when OF is not enabled, this does
not save us enough to justify ugly ifdefs. Clean this up.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix kernel-doc formatting for structs, and while we are making little
fixes, clarify the module description and update the copywrite.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When writing a value using direct reg access from debugfs
we need to return and not fall through to reading the
value, lest we'll dereference a NULL pointer.
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The > here should be >= or we go beyond the end for the array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
mask and val parameters of regmap_update_bits were reveresed.
Fixes: 77c4ad2d6a ("iio: imu: Add initial support for Bosch BMI160")
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Format is INT_PLUS_MICRO and micro odr part of ODR should
be parts of a micro.
Also s/8000/800 this is obviously a typo.
Fixes: 77c4ad2d6a ("iio: imu: Add initial support for Bosch BMI160")
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Disabling of the touchscreen IRQs should be done in
mxs_lradc_disable_ts. So disable only the masked virtual channels
in mxs_lradc_hw_stop and finally remove the unused function
mxs_lradc_irq_en_mask.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
After using devm_input_allocate_device for registration
the function mxs_lradc_ts_unregister isn't necessary anymore
since mxs_lradc_ts_close already does the job.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch simplifies the TS registration of mxs-lradc by
using devm_input_allocate_device.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Minimal implementation of an IIO driver for the Freescale
MMA7660FC 3-axis accelerometer. Datasheet:
http://www.nxp.com/files/sensors/doc/data_sheet/MMA7660FC.pdf
Includes:
- ACPI support;
- read_raw for x,y,z axes;
- reading and setting the scale (range) parameter.
- power management
Signed-off-by: Constantin Musca <constantin.musca@intel.com>
Reviewed-by: Martin Klepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When using ACPI, id is NULL and the current code automatically
defaults name to NULL and chip id to 0. We should instead use
the data provided in the ACPI device table.
Fixes: c816d9e7a5 ("iio: imu: mpu6050: fix possible NULL dereferences")
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Reviewed-By: Matt Ranostay <matt.ranostay@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix possible null dereferencing of i2c and spi driver data.
Signed-off-by: Matt Ranostay <matt.ranostay@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Apex Embedded Systems STX104 DAC drivers does not do anything
special in module init/exit. This patch eliminates the module init/exit
boilerplate code by utilizing the module_isa_driver macro.
Additionally, the max_num_isa_dev macro is utilized to simplify the
determination of maximum possible STX104 devices in the system.
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Apex Embedded Systems STX104 DAC driver expects the STX104 device to
be I/O port-mapped addressable on an X86 platform. This patch adds an
explicit X86 dependency to the STX104 configuration option to prevent
building on non-X86 architectures.
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device has simple 8-bit registers but the driver incorrectly uses
block or word reads without checking functionality bits.
Fix by using i2c_smbus_read_i2c_block_data_or_emulated instead of
i2c_smbus_read_i2c_block_data or i2c_smbus_read_word_data. This will
check functionality bits and use the fastest available transfer method.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Bit of a bumper set for new drivers but plenty of other stuff here as well!
New device support
* ad5592R ADC/DAC
- new driver supporting ad5592r and ad5593r combined ADC/DAC and gpio chips.
* Aosong am2315 relative humidity
- new driver with triggered buffer support in follow up patch.
* bmi160 imu
- new driver
* bmp280
- bmp180 support - note there is support in the misc/bmp085 driver. Intent
is to remove that driver long term.
* invensense mpu6050
- cleanup leading to explicit support of mpu9150 with a good few cleanups
along the way.
* Hope RF hp03 pressure and temperature sensor.
- new driver
* maxim DS1803 potentiometer
- new driver
* maxim max44000 light and proximity sensor
- new driver built in a series of steps to support pretty much everything.
* ROHM BH1780 light sensor
- new driver. There is an existing driver in misc that this is pretty much
intended to replace. The discussion on whether to support the non standard
interface of that driver is some way is continuing.
* st-gyro
- lsm9ds0-gyro. The accel/magn side of this will take a while longer as
extensions to the st library are needed for cases where two types of sensor
share a single i2c address.
* ti-adc081c
- support the adc101c and adc121c
* Vishay VEML6070 UV sensor
- new driver.
New features
* core
- devm_ APIs for channel_get and channel_get_all. The first user of these
is the generic ADC based thermal driver. As it is going through the
thermal tree these will be picked up as a patch to that next cycle as that
is how the author preferred to do it.
- mounting matrix support. This new core support allows devices to provide
to userspace (typically from the device tree) allowing compensation for how
the sensor is mounted on the device. First examples are on UAVs but it
has a more mundane use on typical phone where the chip may be on the front
or the back of the circuit board and soldered at any angle. Includes
support for this ABI in ak8975 (which has an older interface, now
deprecated) and mpu6050.
* tools
- add a -a option to enable all available channels in generic_buffer sample.
Makes it somewhat easier to use.
* adis library and drivers
- support manual self test flag clearing. This has technically been broken
for a very long time - result is an offset on readings as the applied field
is on all the time.
* ak8975
- triggered buffer support
* bmc150
- spi support (including splitting the driver into core and i2c parts)
* bmp280
- oversampling support.
* dht11
- improved logging - useful to debug timing issues on this quirky device.
* st-sensors
- read each channel invidivually as not all support the optimization of
reading in bulk. This is technically a fix, but will need to be backported
if desired.
- support open drain and shared interrupts.
* ti-adc081c
- triggered buffer support.
Cleanups
* inkern
- white space fix.
* ad7606
- use the iio_device_claim_direct_mode call rather than open coding equiv.
* ad799x
- white space fix.
* ad9523
- unsigned -> unsigned int
* apds9660
- brace location tidying up.
- silence an uninitialized variable warning.
* ak8975
- else and brace on same line fix.
* at91_adc
- white space fixes.
* bmc150
- use regmap stored copy of the device pointer rather than having an
additional copy.
* bmg160
- use regmap stored copy of the device pointer rather than having an
additional copy.
* hid-sensors
- white space fixes.
* mcp3422
- white space fix.
* mma7455
- use regmap to retrieve the device struct rather than carrying another copy
in the private data.
* ms_sensors
- white space fix.
* mxs-lradc
- move current bindings out of staging - some will be shortly deprecated but
the reality is that we have device trees out there using them so they will
need to be supported for some time. They accidentally got left behind
when the driver graduated from staging.
- white space cleanup.
- set INPUT_PROP_DIRECT.
- move ts config into a better function.
- move the STMP reset out of the ADC init.
* vf610_adc
- case label indenting fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=zzV9
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.7b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing
Jonathan writes:
2nd set of new device support, features and cleanup for IIO in the 4.7 cycle.
Bit of a bumper set for new drivers but plenty of other stuff here as well!
New device support
* ad5592R ADC/DAC
- new driver supporting ad5592r and ad5593r combined ADC/DAC and gpio chips.
* Aosong am2315 relative humidity
- new driver with triggered buffer support in follow up patch.
* bmi160 imu
- new driver
* bmp280
- bmp180 support - note there is support in the misc/bmp085 driver. Intent
is to remove that driver long term.
* invensense mpu6050
- cleanup leading to explicit support of mpu9150 with a good few cleanups
along the way.
* Hope RF hp03 pressure and temperature sensor.
- new driver
* maxim DS1803 potentiometer
- new driver
* maxim max44000 light and proximity sensor
- new driver built in a series of steps to support pretty much everything.
* ROHM BH1780 light sensor
- new driver. There is an existing driver in misc that this is pretty much
intended to replace. The discussion on whether to support the non standard
interface of that driver is some way is continuing.
* st-gyro
- lsm9ds0-gyro. The accel/magn side of this will take a while longer as
extensions to the st library are needed for cases where two types of sensor
share a single i2c address.
* ti-adc081c
- support the adc101c and adc121c
* Vishay VEML6070 UV sensor
- new driver.
New features
* core
- devm_ APIs for channel_get and channel_get_all. The first user of these
is the generic ADC based thermal driver. As it is going through the
thermal tree these will be picked up as a patch to that next cycle as that
is how the author preferred to do it.
- mounting matrix support. This new core support allows devices to provide
to userspace (typically from the device tree) allowing compensation for how
the sensor is mounted on the device. First examples are on UAVs but it
has a more mundane use on typical phone where the chip may be on the front
or the back of the circuit board and soldered at any angle. Includes
support for this ABI in ak8975 (which has an older interface, now
deprecated) and mpu6050.
* tools
- add a -a option to enable all available channels in generic_buffer sample.
Makes it somewhat easier to use.
* adis library and drivers
- support manual self test flag clearing. This has technically been broken
for a very long time - result is an offset on readings as the applied field
is on all the time.
* ak8975
- triggered buffer support
* bmc150
- spi support (including splitting the driver into core and i2c parts)
* bmp280
- oversampling support.
* dht11
- improved logging - useful to debug timing issues on this quirky device.
* st-sensors
- read each channel invidivually as not all support the optimization of
reading in bulk. This is technically a fix, but will need to be backported
if desired.
- support open drain and shared interrupts.
* ti-adc081c
- triggered buffer support.
Cleanups
* inkern
- white space fix.
* ad7606
- use the iio_device_claim_direct_mode call rather than open coding equiv.
* ad799x
- white space fix.
* ad9523
- unsigned -> unsigned int
* apds9660
- brace location tidying up.
- silence an uninitialized variable warning.
* ak8975
- else and brace on same line fix.
* at91_adc
- white space fixes.
* bmc150
- use regmap stored copy of the device pointer rather than having an
additional copy.
* bmg160
- use regmap stored copy of the device pointer rather than having an
additional copy.
* hid-sensors
- white space fixes.
* mcp3422
- white space fix.
* mma7455
- use regmap to retrieve the device struct rather than carrying another copy
in the private data.
* ms_sensors
- white space fix.
* mxs-lradc
- move current bindings out of staging - some will be shortly deprecated but
the reality is that we have device trees out there using them so they will
need to be supported for some time. They accidentally got left behind
when the driver graduated from staging.
- white space cleanup.
- set INPUT_PROP_DIRECT.
- move ts config into a better function.
- move the STMP reset out of the ADC init.
* vf610_adc
- case label indenting fix.
This device is a package containing a MPU6050-like sensor and an AK8975
magnetometer. The magnetometer component is supported by the existing
ak8975 driver.
This patch also rephrases the Kconfig descriptions.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Acked-by: Ge Gao <ggao@invensense.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Acked-by: Ge Gao <ggao@invensense.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This can be used to distinguish mpu6500. This is a warning rather than
an error because the differences are mostly irrelevant and it's nice to
avoid breaking users with slightly incorrect ACPI/DT.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Acked-by: Ge Gao <ggao@invensense.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This field was unused and incorrect for mpu6500.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The hw_info array was indexed by enum inv_devices chip_type despite the
fact that the enumeration had more members than the array and was
ordered differently.
The patch cleans this up and adds explicit chip_types to i2c/spi/acpi
IDs. It also adds some stricter checks inside the driver core.
This happened to work so far because the differences between the
supported models are very minor.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Acked-by: Ge Gao <ggao@invensense.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds ability to control the oversampling ratio of the temperature
and pressure measurement for both bmp180 and bmp280.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Vlad Dogaru <vlad.dogaru@intel.com>
Cc: Christoph Mair <christoph.mair@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for the BMP180 to the bmp280 iio driver.
The BMP180 has already been supported by misc/bmp085 driver but it
doesn't use iio framework. This change adds the kconfig dependency
not to be selected both of them in order to avoid any issues.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Vlad Dogaru <vlad.dogaru@intel.com>
Cc: Christoph Mair <christoph.mair@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch exposes ALSTIM as illuminance_integration_time and ALSPGA as
illuminance_scale.
Changing ALSTIM also changes the number of bits available in the data
register. This is handled inside raw value reading because:
* It's very easy to shift a few bits
* It allows SCALE and INT_TIME to be completely independent controls
* Buffer support requires constant scan_type.realbits per-channel
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is exposed as an output channel with "led" as an extend_name.
Other sensors also have support for controlling an external LED. It's
not clear that simply exposing an undecorated output channel is the
correct approach.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The proximity sensor relies on sending pulses to an external IR led and
it is disabled by default on powerup. The driver will enable it with a
default power setting.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This just adds support for reporting illuminance with default settings.
Important default registers are written on probe because the device
otherwise lacks a reset function.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add basic support for the Aosong AM2315 relative humidity
and ambient temperature sensor.
Includes support for raw readings and ACPI detection.
Datasheet:
http://www.aosong.com/asp_bin/Products/en/AM2315.pdf
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for HopeRF pressure and temperature sensor.
This device uses two fixed I2C addresses, one for storing
calibration coefficients and another for accessing the ADC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Matt Ranostay <mranostay@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This device has an identical interface to other supported sensors and the patch
only adds IDs.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
It causes a static checker warning if we use "buf" on the failure path
so move that inside the if statement.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add a new rotation matrix sysfs attribute compliant with IIO core
mounting matrix API.
Matrix is retrieved from "in_anglvel_mount_matrix" and
"in_accel_mount_matrix" sysfs attributes. It is declared into mpu6050 DTS
entry as a "mount-matrix" property.
Old interface is kept for backward userspace compatibility and may be
retrieved from legacy platform_data mechanism only.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Expose a rotation matrix to indicate userspace the chip orientation with
respect to the overall hardware system.
Matrix is retrieved from "in_mount_matrix". It is declared into ak8975 DTS
entry as a "mount-matrix" property.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Expose a rotation matrix to indicate userspace the chip placement with
respect to the overall hardware system. This is needed to adjust
coordinates sampled from a sensor chip when its position deviates from the
main hardware system.
Final coordinates computation is delegated to userspace since:
* computation may involve floating point arithmetics ;
* it allows an application to combine adjustments with arbitrary
transformations.
This 3 dimentional space rotation matrix is expressed as 3x3 array of
strings to support floating point numbers. It may be retrieved from a
"[<dir>_][<type>_]mount_matrix" sysfs attribute file. It is declared into a
device / driver specific DTS property or platform data.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Tested-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Driver includes struct regmap and struct device in its global data.
Remove the struct device and use regmap API to retrieve device info.
Patch created using Coccinelle plus manual edits.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Driver includes struct regmap and struct device in its global data.
Remove the struct device and use regmap API to retrieve device info.
Patch created using Coccinelle plus manual edits.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Reviewed-by: Irina Tirdea <irina.tirdea@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
ultraviolet (UV) light sensor with I2C interface with a peak
sensitivity at 355 nm
strangely, chip uses two addresses 0x38 and 0x39 for LSB and
MSB data, resp.
datasheet: http://www.vishay.com/docs/84277/veml6070.pdf
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some of kernel driver uses the IIO framework to get the sensor
value via ADC or IIO HW driver. The client driver get iio channel
by iio_channel_get_all() and release it by calling
iio_channel_release_all().
Add resource managed version (devm_*) of these APIs so that if client
calls the devm_iio_channel_get_all() then it need not to release it
explicitly, it can be done by managed device framework when driver
get un-binded.
This reduces the code in error path and also need of .remove callback in
some cases.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some of kernel driver uses the IIO framework to get the sensor
value via ADC or IIO HW driver. The client driver get iio channel
by iio_channel_get() and release it by calling iio_channel_release().
Add resource managed version (devm_*) of these APIs so that if client
calls the devm_iio_channel_get() then it need not to release it explicitly,
it can be done by managed device framework when driver get un-binded.
This reduces the code in error path and also need of .remove callback in
some cases.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some types of ST Sensors can be connected to the same IRQ line
as other peripherals using open drain. Add a device tree binding
and a sensor data property to flip the right bit in the interrupt
control register to enable open drain mode on the INT line.
If the line is set to be open drain, also tag on IRQF_SHARED
to the IRQ flags when requesting the interrupt, as the whole
point of using open drain interrupt lines is to share them with
more than one peripheral (wire-or).
Cc: devicetree@vger.kernel.org
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Rob Herring <rob@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This makes all ST sensor drivers check that they actually have
new data available for the requested channel(s) before claiming
an IRQ, by reading the status register (which is conveniently
the same for all ST sensors) and check that the channel has new
data before proceeding to read it and fill the buffer.
This way sensors can share an interrupt line: it can be flaged
as shared and then the sensor that did not fire will return
NO_IRQ, and the sensor that fired will handle the IRQ and
return IRQ_HANDLED.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The current buffer read code tries to optimize reads from the
sensor data registers by issuing a single read operation across
all the indata registers.
This doesn't work: when the LIS331DL accelerometer sensor is
configured to open drain, active low interrupt mode, this will
just clear the XDA (X-axis data available) bit in the STATUS_REG
register (0x27), while YDA, ZDA and even ZYXDA remain set to 1,
and the internal logic of the sensor holds the DRDY (INT1) line
asserted (the value of the status register is 0xee).
If we instead issue one read operation per enabled channel
(X, Y, Z) things start working and we can use open drain and
active low interrupts.
Note that a backported patch fixing this issue will be heading
via the fixes branch but changes in this file already in staging-next
will make that patch 'look' rather different. The code in here
is the correct one when that clash hits.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch moves the STMP reset out of ADC init function so as to remove
the possiblity of an error return which will be necessary for PM ops support
patches to follow.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch moves the touchscreen type configuration into
a more suitable function. Btw this simplifies PM ops later.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is useful for easily adding SPI support in later patches.
Now bmc150_magn exports core functions to be used by I2C/SPI drivers
instances. For the moment only I2C driver is supported.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Acked-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
If i2c_device_id *id is NULL and acpi_match_device returns NULL too,
then chipset may be unitialized when accessing &ak_def_array[chipset] in
ak8975_probe. Therefore initialize chipset to AK_MAX_TYPE, which will
return an error when not changed.
This patch fixes the following maybe-uninitialized warning:
drivers/iio/magnetometer/ak8975.c: In function ‘ak8975_probe’:
drivers/iio/magnetometer/ak8975.c:788:14: warning: ‘chipset’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
data->def = &ak_def_array[chipset];
Signed-off-by: Richard Leitner <dev@g0hl1n.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In certain probe conditions the interrupt came right after registering
the handler causing a NULL pointer exception because of uninitialized
waitqueue:
$ udevadm trigger
i2c-gpio i2c-gpio-1: using pins 143 (SDA) and 144 (SCL)
i2c-gpio i2c-gpio-3: using pins 53 (SDA) and 52 (SCL)
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = e8b38000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in: snd_soc_i2s(+) i2c_gpio(+) snd_soc_idma snd_soc_s3c_dma snd_soc_core snd_pcm_dmaengine snd_pcm snd_timer snd soundcore ac97_bus spi_s3c64xx pwm_samsung dwc2 exynos_adc phy_exynos_usb2 exynosdrm exynos_rng rng_core rtc_s3c
CPU: 0 PID: 717 Comm: data-provider-m Not tainted 4.6.0-rc1-next-20160401-00011-g1b8d87473b9e-dirty #101
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
(...)
(__wake_up_common) from [<c0379624>] (__wake_up+0x38/0x4c)
(__wake_up) from [<c0a41d30>] (ak8975_irq_handler+0x28/0x30)
(ak8975_irq_handler) from [<c0386720>] (handle_irq_event_percpu+0x88/0x140)
(handle_irq_event_percpu) from [<c038681c>] (handle_irq_event+0x44/0x68)
(handle_irq_event) from [<c0389c40>] (handle_edge_irq+0xf0/0x19c)
(handle_edge_irq) from [<c0385e04>] (generic_handle_irq+0x24/0x34)
(generic_handle_irq) from [<c05ee360>] (exynos_eint_gpio_irq+0x50/0x68)
(exynos_eint_gpio_irq) from [<c0386720>] (handle_irq_event_percpu+0x88/0x140)
(handle_irq_event_percpu) from [<c038681c>] (handle_irq_event+0x44/0x68)
(handle_irq_event) from [<c0389a70>] (handle_fasteoi_irq+0xb4/0x194)
(handle_fasteoi_irq) from [<c0385e04>] (generic_handle_irq+0x24/0x34)
(generic_handle_irq) from [<c03860b4>] (__handle_domain_irq+0x5c/0xb4)
(__handle_domain_irq) from [<c0301774>] (gic_handle_irq+0x54/0x94)
(gic_handle_irq) from [<c030c910>] (__irq_usr+0x50/0x80)
The bug was reproduced on exynos4412-trats2 (with a max77693 device also
using i2c-gpio) after building max77693 as a module.
Cc: <stable@vger.kernel.org>
Fixes: 94a6d5cf7c ("iio:ak8975 Implement data ready interrupt handling")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Set INPUT_PROP_DIRECT to indicate that it is a touchscreen on the
device to help userspace classify it.
Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Using this requires software triggers like CONFIG_IIO_HRTIMER_TRIGGER.
The device can be configured to do internal periodic sampling but does not
offer some sort of interrupt on data ready. Interrupts can only trigger when
values get out of a specific range.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fix checkpatch warnings:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is a reimplementation of the old misc device driver for the
ROHM BH1780 ambient light sensor (drivers/misc/bh1780gli.c).
Differences from the old driver:
- Uses the IIO framework
- Uses runtime PM to idle the hardware after 5 seconds
- No weird custom power management from userspace
- No homebrewn values in sysfs
This uses the same (undocumented) device tree compatible-string
as the old driver ("rohm,bh1780gli").
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some variants of the devices from the ADIS family don't auto-clear the
self-test bit after the self-test has completed. Instead we have to
manually clear. Add support for this to the ADIS library.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the errors reported by checkpatch.pl:
ERROR: code indent should use tabs where possible
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the error reported by checkpatch.pl:
ERROR: else should follow close brace '}'
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the error reported by checkpatch.pl:
ERROR: code indent should use tabs where possible
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the error reported by checkpatch.pl:
ERROR: code indent should use tabs where possible
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the error reported by checkpatch.pl:
ERROR: space prohibited before that ',' (ctx:WxW)
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the errors reported by checkpatch.pl:
ERROR: space prohibited before that ',' (ctx:WxW)
ERROR: code indent should use tabs where possible
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the error reported by checkpatch.pl:
ERROR: space prohibited before that ',' (ctx:WxW)
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the error reported by checkpatch.pl:
ERROR: switch and case should be at the same indent
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the error reported by checkpatch.pl:
ERROR: space required before the open parenthesis '('
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the error reported by checkpatch.pl:
ERROR: that open brace { should be on the previous line
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
BMI160 is an Inertial Measurement Unit (IMU) which provides acceleration
and angular rate measurement. It also offers a secondary I2C interface
for connecting a magnetometer sensor (usually BMM160).
Current driver offers support for accelerometer and gyroscope readings
via sysfs or via buffer interface using an external trigger (e.g.
hrtimer). Data is retrieved from IMU via I2C or SPI interface.
Datasheet is at:
http://www.mouser.com/ds/2/783/BST-BMI160-DS000-07-786474.pdf
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This resolves a lot of merge issues with PAGE_CACHE_* changes, and an
iio driver merge issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Unify log messages
* Add more DEBUG messages
Apparently this driver is working unreliably on some platforms that I can't
test. Therefore I want an easy way for bug reporters to provide useful
information without making the driver too chatty by default.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Driver includes struct regmap and struct device in its global data.
Remove the struct device and use regmap API to retrieve device info.
Patch created using Coccinelle plus manual edits.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for the AD5592R (spi) and AD5593R (i2c)
ADC/DAC/GPIO devices.
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This will be used together with an external trigger (e.g hrtimer based
software trigger).
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The following functions are supported:
- write, read potentiometer value
- potentiometer scale
Datasheet: https://datasheets.maximintegrated.com/en/ds/DS1803.pdf
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This lot are either dependent on patches from the merge window or just came
in recently enough that they ended up in this tree.
* core
- The watermark for the buffers was given a value that meant that it was
impossible to actually set the watermark to anything sensible.
* at91_adc
- Fix a build config dependency on HAS_IOMEM
* bmc150
- Fix wrong output on big endian systems
* bmg160
- Fix wrong output on big endian systems
- Fix an issue in which the regmap return value was stored to the buffer
rather than the value actually being read in a bulk read.
* inv_mpu6050
- Fix an indirect build config dependency on HAS_IOMEM
* max30100
- Fix an error in fifo check condition that leads to a double read of the
final reading.
* st_magn
- Make sure ST_MAGN_TRIGGER_SET_STATE is always defined to avoid a build
error for relatively obscure config combinations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=j/qV
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.6b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 4.6 cycle.
This lot are either dependent on patches from the merge window or just came
in recently enough that they ended up in this tree.
* core
- The watermark for the buffers was given a value that meant that it was
impossible to actually set the watermark to anything sensible.
* at91_adc
- Fix a build config dependency on HAS_IOMEM
* bmc150
- Fix wrong output on big endian systems
* bmg160
- Fix wrong output on big endian systems
- Fix an issue in which the regmap return value was stored to the buffer
rather than the value actually being read in a bulk read.
* inv_mpu6050
- Fix an indirect build config dependency on HAS_IOMEM
* max30100
- Fix an error in fifo check condition that leads to a double read of the
final reading.
* st_magn
- Make sure ST_MAGN_TRIGGER_SET_STATE is always defined to avoid a build
error for relatively obscure config combinations.
Again I've ended up with two early fix sets, depending on whether they are
dependent on elements of the merge window or simply came in after I had
patches with that dependency already, vs older fixes that were just too
late for the last cycle. This first set is for the older ones.
- max1353
* Add a missing adc to max1363_id - the driver has supported the
max11644-11647 for a while, but as they weren't in the id table there
was no way of actually initializing it.
* Fix a wrong reference voltage for the above models. Given you couldn't
initialize the driver for these parts without patching, no one noticed
that the reference voltage used in computing the scaling was wrong.
- apds9960
* The fifo last enelement was read twice (and hence pushed out twice) due
to a small logic bug.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Bfg6
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into usb-linus
Jonathan writes:
First round of IIO fixes for the 4.6 cycle.
Again I've ended up with two early fix sets, depending on whether they are
dependent on elements of the merge window or simply came in after I had
patches with that dependency already, vs older fixes that were just too
late for the last cycle. This first set is for the older ones.
- max1353
* Add a missing adc to max1363_id - the driver has supported the
max11644-11647 for a while, but as they weren't in the id table there
was no way of actually initializing it.
* Fix a wrong reference voltage for the above models. Given you couldn't
initialize the driver for these parts without patching, no one noticed
that the reference voltage used in computing the scaling was wrong.
- apds9960
* The fifo last enelement was read twice (and hence pushed out twice) due
to a small logic bug.
New core support
* UV light modifier (for intensity)
* UV light index channel type.
New device support
* hp206c barometer and altimeter
- new driver.
* mcp4131 potentiometer
- new driver supporting lots of parts from Microchip.
* mma8452
- FXLS8471Q support
- NXP LPC18XX SOC ADC
- new driver.
- NXP LPC18XX SOC DAC
- new driver.
- rockchip_saradc
- support rk3399
* st accel
- h3lis331dl support
Staging driver removals
* adis16204
- obsolete part making it hard to get parts to test the driver in order
to clean it up.
* adis16220
- obsolete part making it hard to get the parts test the driver in order
to clean it up.
Features
* core
- convenience functions to claim / release direct access to the device.
Makes more consistent handling of this corner easier. Used in ad7192 driver.
* ak8975
- power regulator support.
* at91-sama5d2
- differential channel support.
* mma8452
- runtime pm support
- drop device specific autosleep and use the runtime pm one instead.
* ms5611
- DT bindings
- oversampling ratio support
Cleanups and minor fixes
* MAINTAINERS
- Peter got married - hence name change!
* Documentation
- Fix a typo in in_proximity_raw description.
- Add some missing docs for iio_buffer_access_funcs.
* Tools
- update iio_event_monitor names to match new stuff.
- make generic_buffer look for triggers ending in -trigger as we let these in
for a number of drivers a long time back and now it is a fairly common
option.
Drivers
* staging wide
- convert bare unsigned usage to unsigned int to comply with coding style.
* non staging wide:
- since boiler plate gpio handling of interrupts has been moved into the
ACPI core we don't need to include gpio/consumer.h in a load of drivers so
drop it.
* ad7606
- fix an endian casting sparse warning.
* ak8975
- fix a possible unitialized warning from gcc.
- drop and unused field left over from earlier cleanups
- fix a missing regulator_disable on exit.
* at91-sama5d2
- typo and indentation
- missing IOMEM dependency.
- cleanup mode register usage by avoidling erasing whole thing when changing
the sampling frequency.
* bmc150
- use the core demux and available_scan_masks to simplify buffer handling
- optimize the transfers in the trigger handler now we have a magic function
to emulate bulk reads (under circumstances met here). This matters with some
rather dumb i2c adapters in particular.
- use a single regmap_conf for all bus types as they were all the same.
* bmg160
- use the core demux and available_scan_masks to simplify the buffer handling
- optimize the transfers in the trigger handler now we have a magic funciton
to emulate bulk rads (under circumstances met here).
- drop gpio interrupt probing from the driver (ACPI) as now handled by the
ACPI core.
* ina2xx-adc
- update the CALIB register when RShunt changes.
- fix scale for VShunt - in reality this error canceled out when used.
* isl29028
- use regmap to retrieve the struct device instead of carrying a second
copy of it around.
* kxcjk-1013
- use core demux
- optimize i2c transfers in the trigger handler.
* mcp4531
- refactor to use a pointer to access model parameters instead of indexing
into the array each time.
* mma8452
- style fixes
- avoid swtiching to active whenever the config changes
- add missin i2c_device_id for mma8451
* mpu6050
- fix possible NULL dereference.
- fix the name / chip_id used when ACPI used (otherwise reports as NULL).
* ms5611
- fix a missing regulator_disable that left the regulator on during removal.
* mxc4005
- drop gpio interrupt handling for ACPI case from driver as the core now
handles this case.
* st-sensors
- note that there are only ever a maximum of 3 axis on current st-sensors
so just allocate a fixed sized buffer big enough for that.
* tpl0102
- change the i2c_check_functionality condition to bring it inline with other
IIO users as EOPNOTSUPP.
* tsl2563
- replace deprecated flush_scheduled_work
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=SgQo
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.7 cycle.
New core support
* UV light modifier (for intensity)
* UV light index channel type.
New device support
* hp206c barometer and altimeter
- new driver.
* mcp4131 potentiometer
- new driver supporting lots of parts from Microchip.
* mma8452
- FXLS8471Q support
- NXP LPC18XX SOC ADC
- new driver.
- NXP LPC18XX SOC DAC
- new driver.
- rockchip_saradc
- support rk3399
* st accel
- h3lis331dl support
Staging driver removals
* adis16204
- obsolete part making it hard to get parts to test the driver in order
to clean it up.
* adis16220
- obsolete part making it hard to get the parts test the driver in order
to clean it up.
Features
* core
- convenience functions to claim / release direct access to the device.
Makes more consistent handling of this corner easier. Used in ad7192 driver.
* ak8975
- power regulator support.
* at91-sama5d2
- differential channel support.
* mma8452
- runtime pm support
- drop device specific autosleep and use the runtime pm one instead.
* ms5611
- DT bindings
- oversampling ratio support
Cleanups and minor fixes
* MAINTAINERS
- Peter got married - hence name change!
* Documentation
- Fix a typo in in_proximity_raw description.
- Add some missing docs for iio_buffer_access_funcs.
* Tools
- update iio_event_monitor names to match new stuff.
- make generic_buffer look for triggers ending in -trigger as we let these in
for a number of drivers a long time back and now it is a fairly common
option.
Drivers
* staging wide
- convert bare unsigned usage to unsigned int to comply with coding style.
* non staging wide:
- since boiler plate gpio handling of interrupts has been moved into the
ACPI core we don't need to include gpio/consumer.h in a load of drivers so
drop it.
* ad7606
- fix an endian casting sparse warning.
* ak8975
- fix a possible unitialized warning from gcc.
- drop and unused field left over from earlier cleanups
- fix a missing regulator_disable on exit.
* at91-sama5d2
- typo and indentation
- missing IOMEM dependency.
- cleanup mode register usage by avoidling erasing whole thing when changing
the sampling frequency.
* bmc150
- use the core demux and available_scan_masks to simplify buffer handling
- optimize the transfers in the trigger handler now we have a magic function
to emulate bulk reads (under circumstances met here). This matters with some
rather dumb i2c adapters in particular.
- use a single regmap_conf for all bus types as they were all the same.
* bmg160
- use the core demux and available_scan_masks to simplify the buffer handling
- optimize the transfers in the trigger handler now we have a magic funciton
to emulate bulk rads (under circumstances met here).
- drop gpio interrupt probing from the driver (ACPI) as now handled by the
ACPI core.
* ina2xx-adc
- update the CALIB register when RShunt changes.
- fix scale for VShunt - in reality this error canceled out when used.
* isl29028
- use regmap to retrieve the struct device instead of carrying a second
copy of it around.
* kxcjk-1013
- use core demux
- optimize i2c transfers in the trigger handler.
* mcp4531
- refactor to use a pointer to access model parameters instead of indexing
into the array each time.
* mma8452
- style fixes
- avoid swtiching to active whenever the config changes
- add missin i2c_device_id for mma8451
* mpu6050
- fix possible NULL dereference.
- fix the name / chip_id used when ACPI used (otherwise reports as NULL).
* ms5611
- fix a missing regulator_disable that left the regulator on during removal.
* mxc4005
- drop gpio interrupt handling for ACPI case from driver as the core now
handles this case.
* st-sensors
- note that there are only ever a maximum of 3 axis on current st-sensors
so just allocate a fixed sized buffer big enough for that.
* tpl0102
- change the i2c_check_functionality condition to bring it inline with other
IIO users as EOPNOTSUPP.
* tsl2563
- replace deprecated flush_scheduled_work
bmc150_i2c_regmap_conf is defined three times (in bmc150-accel-core.c,
bmc150-accel-i2c.c and and bmc150-accel-spi.c), although the
definition is the same.
Use one common definition for bmc150_i2c_regmap_conf in all
included files.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When reading gyroscope axes using iio buffers, the values
returned are always 0. In the interrupt handler, the return
value of the read operation is returned to the user instead
of the value read. Return the value read to the user.
This is also fixed in commit 82d8e5da1a33 ("iio:
accel: bmg160: optimize transfers in trigger handler").
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
For big endian platforms, reading the axes will return
invalid values.
The device stores each axis value in a 16 bit little
endian register. The driver uses regmap_read_bulk to get
the axis value, resulting in a 16 bit little endian value.
This needs to be converted to cpu endianness to work
on big endian platforms.
Fix endianness for big endian platforms by converting
the values for the axes read from little endian to
cpu.
This is also partially fixed in commit 82d8e5da1a33 ("iio:
accel: bmg160: optimize transfers in trigger handler").
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
For big endian platforms, reading the axes will return
invalid values.
The device stores each axis value in a 16 bit little
endian register. The driver uses regmap_read_bulk to get
the axis value, resulting in a 16 bit little endian value.
This needs to be converted to cpu endianness to work
on big endian platforms.
Fix endianness for big endian platforms by converting
the values for the axes read from little endian to
cpu.
This is also partially fixed in commit b6fb9b6d6552 ("iio:
accel: bmc150: optimize transfers in trigger handler").
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
UV index indicating strength of sunburn-producing ultraviolet (UV) radiation
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The scale would result in uV instead of expected mV.
Mostly cosmetic, since the value of 'Power' was computed OK.
Signed-off-by: Marc Titinger <marc.titinger@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add signed differential channels and update the voltage scale for
differential conversions.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Do not erase previous configuration of the mode register when setting
the sampling frequency.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The following functionalities are supported:
- write, read from volatile memory
Datasheet: http://ww1.microchip.com/downloads/en/DeviceDoc/22060b.pdf
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Reviewed-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When CONFIG_IIO_TRIGGER is enabled but CONFIG_IIO_BUFFER is
not, we get a build error in the st_magn driver:
drivers/iio/magnetometer/st_magn_core.c:573:23: error: 'ST_MAGN_TRIGGER_SET_STATE' undeclared here (not in a function)
.set_trigger_state = ST_MAGN_TRIGGER_SET_STATE,
^~~~~~~~~~~~~~~~~~~~~~~~~
Apparently, this ST_MAGN_TRIGGER_SET_STATE macro was meant to
be set to NULL when the definition is not available because
st_magn_buffer.c is not compiled, but the alternative definition
was not included in the original patch. This adds it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 74f5683f35 ("iio: st_magn: Add irq trigger handling")
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Commit 845c877009 ("i2c / ACPI: Assign IRQ for devices that have
GpioInt automatically") automatically assigns the first ACPI GPIO
interrupt in client->irq, so we can remove the probing code from
drivers that use only one interrupt.
Commit 0f0796509c ("iio: remove gpio interrupt probing from drivers
that use a single interrupt") removes gpio interrupt probing from most
drivers. This patch cleans the remaining ones.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
GPIO handling code has been removed from the drivers (since
this is now handled by the ACPI core) in commit 0f0796509c ("iio:
remove gpio interrupt probing from drivers that use a single interrupt").
Remove the include for linux/gpio/consumer.h since it is no longer
used.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some i2c busses (e.g.: Synopsys DesignWare I2C adapter) need to
enable/disable the bus at each i2c transfer and must wait for
the enable/disable to happen before sending the data.
When reading data in the trigger handler, the kxcjk-1013 accel driver
does one i2c transfer for each axis. This has an impact on the
frequency of the accelerometer at high sample rates due to additional
delays introduced by the i2c bus at each transfer.
Reading all axis values in one i2c transfer reduces the delays
introduced by the i2c bus. Uses i2c_smbus_read_i2c_block_data_or_emulated
that will fallback to reading each axis as a separate word in case i2c
block read is not supported.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use available_scan_masks to allow the iio core to select
the data to send to userspace depending on which axes are
enabled, instead of doing this in the driver's interrupt
handler.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some i2c busses (e.g.: Synopsys DesignWare I2C adapter) need to
enable/disable the bus at each i2c transfer and must wait for
the enable/disable to happen before sending the data.
When reading data in the trigger handler, the bmg160 gyro driver does
one bus transfer for each axis. This has an impact on the frequency
of the accelerometer at high sample rates due to additional delays
introduced by the bus at each transfer.
Reading all axis values in one bus transfer reduces the delays
introduced by the bus.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use available_scan_masks to allow the iio core to select
the data to send to userspace depending on which axes are
enabled, instead of doing this in the driver's interrupt
handler.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some i2c busses (e.g.: Synopsys DesignWare I2C adapter) need to
enable/disable the bus at each i2c transfer and must wait for
the enable/disable to happen before sending the data.
When reading data in the trigger handler, the bmc150 accel driver does
one bus transfer for each axis. This has an impact on the frequency
of the accelerometer at high sample rates due to additional delays
introduced by the bus at each transfer.
Reading all axis values in one bus transfer reduces the delays
introduced by the bus.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use available_scan_masks to allow the iio core to select
the data to send to userspace depending on which axes are
enabled, instead of doing this in the driver's interrupt
handler.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use const pointer to element from model configuration array rather then array
index, as it will not change anyway.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
config structure is set to 0 when updating the buffers, so by
default config->watermark will be 0. When computing the minimum
between config->watermark and the buffer->watermark or
insert_buffer-watermark, this will always be 0 regardless of the
value set by the user for the buffer.
Set as initial value for config->watermark the maximum allowed
value so that the minimum value will always be set from one of the
buffers.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Fixes: f0566c0c40 ("iio: Set device watermark based on watermark of all
attached buffers")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Correct issue that the last entry in FIFO was being read twice due
to an incorrect decrement of entry count variable before condition
check.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Not all archs have io memory.
Instead of selecting I2C_MUX (and bypassing the HAS_IOMEM dependency)
depend directly on it.
Fixes the following kconfig warning:
warning: (MEDIA_SUBDRV_AUTOSELECT && VIDEO_CX231XX && INV_MPU6050_I2C) selects I2C_MUX which has unmet direct dependencies (I2C && HAS_IOMEM)
And this build error:
ERROR: "devm_ioremap_resource" [drivers/i2c/muxes/i2c-mux-reg.ko] undefined!
ERROR: "of_address_to_resource" [drivers/i2c/muxes/i2c-mux-reg.ko] undefined!
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The devres.o gets linked if HAS_IOMEM is present so on ARCH=um
allyesconfig (COMPILE_TEST) failed with:
drivers/built-in.o: In function `at91_adc_probe':
at91-sama5d2_adc.c:(.text+0x48f548): undefined reference to `devm_ioremap_resource'
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver goes to some length to dynamically allocate an array
to hold the channel addresses. However no ST sensor has more than
three channels (x, y, z at most). Instead of kmalloc():ing and
kfree():in the address array, just use a fixed array of three
elements.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The user (or an init script) may setup RShunt via sysfs after the
driver was initialized, for instance based on the EEPROM contents
of a modular probe. The calibration register must be set accordingly.
Signed-off-by: Marc Titinger <marc.titinger@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Ensure optional regulator is properly disabled when present.
Fixes: 63d5d525cb ("iio:magnetometer:ak8975: power regulator support")
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
flush_scheduled_work is scheduled for deprecation.
Replace cancel_delayed_work and flush_scheduled_work with
cancel_delayed_work_sync instead to ensure there is no pending or
running work item.
Since there is only one work item, chip->poweroff_work, there are
no further dependencies of flush_scheduled_work().
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Ensure optional regulator is properly disabled when present.
Fixes: 3145229f91 ("iio:pressure:ms5611: power regulator support")
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When using ACPI, id is NULL and the current code automatically
defaults name to NULL and chip id to 0. We should instead use
the data provided in the ACPI device table.
Fixes: c816d9e7a5 ("iio: imu: mpu6050: fix possible NULL dereferences")
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Reviewed-By: Matt Ranostay <matt.ranostay@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Correct issue that the last entry in FIFO was being read twice due
to an incorrect decrement of entry count variable before condition
check.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Swap max11644/max11645 and max 11646/max11647 reference voltages according
to datasheet.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
max11644-max11647 had an enum value but were not added to the max1363_id,
so they where not selectable in the devictree.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ADC is a 6-channel signal-ended 10-bit Successive
Approximation Register (SAR) A/D Converter.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
What is this autosleep?
-----------------------
It slows down the device after x seconds of inactivity. The thing is, we have
really achieved almost the same by runtime pm.
differnces are:
autosleep
* uses more power during inactivity
* the first read after inactivity slightly faster
* complicated to understand for the user
* no documented sysfs interface (afaik)
* complicated to read and maintain
runtime pm
* already merged in mma8452
* uses less power during inactivity
* first read after inactivity slower
* easy to use. well documented.
* easy to maintain and understand
The two approaches solve the same problem. runtime pm has more advantages
than autosleep and comes quite close to it's behaviour anyways. As I see it,
autosleep, even if somehow supported, would never be used anyways.
So resolve this issue by "ignoring" autosleep.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Reviewed-by: Martina Kepplinger <martina.novakovic@zoho.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This was forgotten about and is added for consistency now
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
- New Device Support
- Supply device PCI IDs for Intel Broxton
- Fix-ups
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
- Bug Fixes
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJW6+LJAAoJEFGvii+H/Hdh8kQP/2AKYzPZiw9fhLufsDPvXO5m
BVdLYVyA11oQjQk7/Bh+5Rjz8mR5Tfv4uAJUReC3FOIfC/oJNBfBxYJLDV/P8S0/
KaCEaZrpNmecKrsy+TjmFYtcRa51THAdjlWEUKRks/ZBjwP4YsNnh5reWe+wB7bS
NFbCNhpXFvYXaDGH8MRhKqdChzZkxi+lgOBcFCKvUYO5/o6g/ZRUD/0TXUItJDwh
F8ps5jImHC1imHeRIKWPNrrZqcYasKmObIhvOKMDcwNQPnjrAWq5QuFH4LFhGQ7d
7NMQrBpaGvZyUNBVtL7ZF1xCJ68wAg/ZvZUkKVkax9ubLbSgf6VXYLQEbq+lyFn7
H9A79xPAGN2nC9HsGnCqW0c0qgTOz0DIkbpuaxAGlzBt0zooc19i3cuUd7LX0NG8
ttLaIP1hX6rgvXSFnF0Ihe3iN5A90LTT3ldbn3A8awyS42vEAbUVL9ivRL21BUbB
ilSTO2W05a9HlIVe43o2euytaGvDYX7RbL/g3WcJLF1pA01RCIDQAI5usMpgF3bf
fJ7cszll0OVTTb5UzbfrNsxAn4oNtbwMIspMMFe17pbmxqh+4oomM3CkuTrMVQfB
pA7Uv0jh/mLCV6P52ZEsNiecn0/l0rID8d/DCHjunr2xBWIOrglzZ7n+vLTJMNJ6
72GVBkYRMLbRm+eph1Tp
=gTBA
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
New Device Support:
- Supply device PCI IDs for Intel Broxton
Fix-ups:
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
Bug Fixes:
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss"
* tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (53 commits)
mfd: intel-lpss: Pass I2C configuration via properties on BXT
mfd: imx6sx: Add PCIe register definitions for iomuxc gpr
mfd: ipaq-micro: Use __maybe_unused to hide pm functions
mfd: max77686: Add max77802 to I2C device ID table
mfd: max77686: Export OF module alias information
mfd: max77686: Allow driver to be built as a module
mfd: stmpe: Add the proper PWM resources
mfd: tps65090: Set regmap config reg counts properly
mfd: syscon: Return ENOTSUPP instead of ENOSYS when disabled
mfd: as3711: Set regmap config reg counts properly
mfd: rc5t583: Set regmap config reg counts properly
gpio: tps65086: Add GPO driver for the TPS65086 PMIC
mfd: mt6397: Add platform device ID table
mfd: da9063: Fix missing volatile registers in the core regmap_range volatile lists
mfd: mt6397: Add MT6323 support to MT6397 driver
mfd: mt6397: Add support for different Slave types
mfd: mt6397: int_con and int_status may vary in location
dt-bindings: mfd: Add bindings for the MediaTek MT6323 PMIC
mfd: da9062: Fix missing volatile registers in the core regmap_range volatile lists
mfd: Add documentation for ACT8945A DT bindings
...
Add base support for the 10-bit DAC peripheral found
on NXP LPC18xx/43xx SoCs.
This is a minimal driver that does not support DMA or
interrupts.
User manual with register description can be found on:
LPC18xx: www.nxp.com/documents/user_manual/UM10430.pdf
LPC43xx: www.nxp.com/documents/user_manual/UM10503.pdf
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add base support for the 10-bit SAR ADC peripheral found
on NXP LPC18xx/43xx SoCs.
This is a minimal driver that does not support burst mode,
interrupts, DMA or hardware triggers.
User manual with register description can be found on:
LPC18xx: www.nxp.com/documents/user_manual/UM10430.pdf
LPC43xx: www.nxp.com/documents/user_manual/UM10503.pdf
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
It is often the case that the driver wants to be sure a device stays
in direct mode while it is executing a task or series of tasks. To
accomplish this today, the driver performs this sequence: 1) take the
device state lock, 2) verify it is not in a buffered mode, 3) execute
some tasks, and 4) release that lock.
This patch introduces a pair of helper functions that simplify these
steps and make it more semantically expressive.
iio_device_claim_direct_mode()
If the device is not in any buffered mode it is guaranteed
to stay that way until iio_release_direct_mode() is called.
iio_device_release_direct_mode()
Release the claim. Device is no longer guaranteed to stay
in direct mode.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for Freescale's (now NXP's) FXLS8471Q accelerometer.
We use MMA8451Q's configuration because for what the driver supports,
FXLS8471Q is the same.
Support for FXLS8471Q's features (fast SPI interface and a larger FIFO,
among others) can be added to this driver anytime.
See it's datasheet for the details:
http://cache.nxp.com/files/sensors/doc/data_sheet/FXLS8471Q.pdf
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This commit adds support for STMicroelectronics h3lis331dl high-g
accelerometer. The datasheet for this device can be found here:
http://www.st.com/web/en/resource/technical/document/
datasheet/DM00053090.pdf
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Reviewed-by: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The newly added driver uses do_div() to device a 32-bit number, which now
provokes a warning:
drivers/iio/adc/fsl-imx25-gcq.c: In function 'mx25_gcq_setup_cfgs':
include/asm-generic/div64.h:207:28: warning: comparison of distinct pointer types lacks a cast
(void)(((typeof((n)) *)0) == ((uint64_t *)0)); \
This replaces the do_div() call with a straight division operator.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 6df2e98c3e ("iio: adc: Add imx25-gcq ADC driver")
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The devres.o gets linked if HAS_IOMEM is present so on ARCH=um
allyesconfig (COMPILE_TEST) failed with:
drivers/built-in.o: In function `at91_adc_probe':
at91-sama5d2_adc.c:(.text+0x48f548): undefined reference to `devm_ioremap_resource'
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix possible null dereferencing of i2c and spi driver data.
Signed-off-by: Matt Ranostay <matt.ranostay@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for runtime power management and, if configured, activates
automatic standby after 2 seconds of inactivity.
Inactivity means no read of acceleration values and no events triggered or
activated.
If CONFIG_PM is not set, this doesn't change anything for existing users.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The devices' config registers can only be changed in standby mode.
Up until now the driver just held the device *always* active, so for
changing a config it was *always* necessary to switch to standby.
For upcoming support for runtime pm, the device can as well be in standby
mode. Instead of putting runtime pm functions in there, just keep the
device in standby if it already is. This section is protected by a lock
after all.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
fix checkpatch issues like "space before tabs", too long lines or alignment.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for an optional regulator which, if found into device-tree,
will power on device at probing time.
The regulator is declared into ak8975 DTS entry as a "vdd-supply" property.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
ak_def_array bounds are not properly checked in case of ACPI matching
failure. GCC warns with the following message at line 799:
‘chipset’ may be used uninitialized in this function.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for setting and retrieving OverSampling Rate independently for
each of the temperature and pressure channels. This allows userspace to
fine tune hardware sampling process according to the following tradeoffs :
* the higher the OSR, the finer the resolution ;
* the higher the OSR, the lower the noise ;
BUT:
* the higher the OSR, the larger the drift ;
* the higher the OSR, the longer the response time, i.e. less samples per
unit of time.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add device-tree ID tables and document bindings.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Change i2c_check_functionality condition check return from ENOTSUPP to
EOPNOTSUPP which is now the standard return code.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Palmas gpadc IRQs are nested threaded and this flag is not required for nested
irqs anymore, since commit 3c646f2c6a ("genirq: Don't suspend nested_thread
irqs over system suspend") was merged.
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Previously most drivers that used a i2c_check_functionality() check
condition required various error codes on failure. This patchset
converts to a standard of -EOPNOTSUPP
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Allow setting of the x/y/z axes calibration offsets for the gyroscope
and accelerometer.
Signed-off-by: Matt Ranostay <matt.ranostay@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
replace msleep(INV_MPU6050_REG_UP_TIME) with usleep_range calls
due to fact the wait time is under 20 milliseconds.
Signed-off-by: Matt Ranostay <matt.ranostay@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add driver support for DAC peripheral on Vybrid SoC.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
These are generally for devlopment use only, remove these
from performance-critical code, convert to dev_dbg elswhere.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Group of probably overly rigorous whitespace and code cleanups.
- Alphabetize includes
- Assign to variables in the order they are defined
- Alignment issues
- Group alike statements together
- Use helper macros
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for the TI family of digital potentiometers.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
removed several trailing whitespaces before assignment operations
Signed-off-by: Matt Ranostay <matt.ranostay@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for an optional regulator which, if found into device-tree,
will power on device at probing time.
The regulator is declared into ms5611 DTS entry as a "vdd-supply" property.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use name of probed device instead of driver's one when registering device.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Computation of sens2 was wrong and is fixed by this patch, sens2 should be:
2 * (t - 2000)^2
See page 8 of ms5607 datasheet here:
http://www.meas-spec.com/product/pressure/MS5607-02BA03.aspx
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This makes code consistent around inv_mpu6050 driver and
fixes the following checkpatch.pl warning:
CHECK: Alignment should match open parenthesis
Note that there were few cases were it was not possible to
fix this due to making the line too long, but we can live with that.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the following checkpatch.pl warning:
WARNING: suspect code indent for conditional statements (8, 24)
+ if (kfifo_len(&st->timestamps) >
[...]
+ goto flush_fifo;
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the following checkpatch.pl warning:
ERROR: space prohibited before that ',' (ctx:WxE)
.shift = 0 ,
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fixes the following checkpatch warning:
CHECK: Unnecessary parentheses around cpm->package.elements[i]
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the following checkpatch.pl warnings:
* WARNING: Missing a blank line after declarations
* CHECK: Blank lines aren't necessary before a close brace '}'
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the following checkpatch warning:
* WARNING: Comparisons should place the constant
on the right side of the test
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Acked-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The preffered style for long (multi-line) comments is:
/*
* this is a multiline
* comment
*/
This also fixes checkpatch.pl warning:
WARNING: Block comments use * on subsequent lines
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replaced i2c_smbus_read_i2c_block_data() with regmap_bulk_read()
function call. This is to make the driver code more consistent.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch moves hmc5843 driver from staging/iio/magnetometer
to iio/magnetometer, updates the corresponding Makefiles and
moves the hmc5843* entries to the 'Industrial I/O support ->
Magnetometer sensors' menu.
Signed-off-by: Cristina Moraru <cristina.moraru09@gmail.com>
Cc: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
switch from using REGCACHE_FLAT to REGCACHE_RBTREE so initial hw values
are read from device. This also allows some volatile ranges to be
dropped.
Note that REGCACHE_FLAT is intended only for very low lag cases so doesn't
do nice things like read initial values from the device. Hence this change.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ms5611 driver started using the IIO_TRIGGERED_BUFFER infrastructure
which in turn depend on IIO_BUFFER, and it produces a build error now
if that is not enabled:
warning: (... && MS5611 && ...) selects IIO_TRIGGERED_BUFFER which has unmet direct dependencies (IIO && IIO_BUFFER)
buffer/industrialio-triggered-buffer.c: In function 'iio_triggered_buffer_setup':
buffer/industrialio-triggered-buffer.c:58:2: error: implicit declaration of function 'iio_device_attach_buffer' [-Werror=implicit-function-declaration]
pressure/ms5611_core.c: In function 'ms5611_trigger_handler':
pressure/ms5611_core.c:193:2: error: implicit declaration of function 'iio_push_to_buffers_with_timestamp' [-Werror=implicit-function-declaration]
This adds the second select.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 713bbb4efb ("iio: pressure: ms5611: Add triggered buffer support")
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The newly added afe4404 driver implements suspend/resume using the
SIMPLE_DEV_PM_OPS() macro, which leaves out references to the actual
functions when CONFIG_PM is disabled, causing a harmless warning:
health/afe4404.c:509:12: error: 'afe4404_suspend' defined but not used
health/afe4404.c:530:12: error: 'afe4404_resume' defined but not used
This marks the functions as __maybe_unused so we don't get those
warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 87aec56e27 ("iio: health: Add driver for the TI AFE4404 heart monitor")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The newly added afe4403 driver implements suspend/resume using the
SIMPLE_DEV_PM_OPS() macro, which leaves out references to the actual
functions when CONFIG_PM is disabled, causing a harmless warning:
health/afe4403.c:509:12: error: 'afe4403_suspend' defined but not used
health/afe4403.c:530:12: error: 'afe4403_resume' defined but not used
This marks the functions as __maybe_unused so we don't get those
warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: eec96d1e2d ("iio: health: Add driver for the TI AFE4403 heart monitor")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The newly added afe4403 driver uses the regmap facility to abstract
the I2C and SPI access. However, it fails to ensure that regmap_spi
is actually present:
drivers/iio/built-in.o: In function `afe4403_probe':
:(.text+0x9bf8): undefined reference to `__devm_regmap_init_spi'
This adds a Kconfig select statement like the afe4404 I2C driver
has.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: eec96d1e2d ("iio: health: Add driver for the TI AFE4403 heart monitor")
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New Device Support
* Apex stx104 DAC
- new driver for this PC104 board. Right now DAC support only.
* ADI ad5064
- Add support for ad5625, ad5627, ad5645, ad5665, ad5667 DACs.
- Add support for Linear Technology ltc2606, ltc2607, ltc2609, ltc2616,
ltc2617, ltc2619, ltc2626, ltc2627 and ltc2629.
* ADI ad7192
- add support for the ad7193
* Invensense mpu6050
- substantial rework of driver to use regmap allowing SPI support extending
the now split driver to cover the MPU6000.
* TI adc0832
- new driver supporting ADC0831, ADC0832, ADC0834 and ADC0838 ADCs.
* TI ads1015
- new driver, note that there is an existing hwmon driver. The long term
intention is to probably remove the hwmon driver but for now we just have
guards in place to ensure this driver is not built if that one is enabled.
* TI afe4403
- new driver for this heart rate monitor / pulse oximeter front end chip.
* TI afe4404
- new driver for this heart rate monitor / pulse oximeter front end chip.
Staging Graduations
* mxs-lradc
- A combined general purpose and touch screen (input) device driver.
Originally held in staging to allow reworking into and MFD but as
that wasn't happening and isn't an absolute requirement we are moving
it out of staging.
Driver new features
* ms5611
- triggered buffer support
- IIO_CHAN_INFO_SCALE to aid the triggered buffer support.
Driver cleanups / reworks / fixes
* ad5064
- Use an enum for the register map layout to allow support of additional
chips (precursor to the new support listed above).
- Structural driver changes to allow support of the slightly different
handling for the ltc parts above.
* ad5933
- drop an exceptional & unnecessary for a function pointer.
* ad7606
- Cleanup the repeated copies of pm ops.
- consolidate the various channels specs via a sport of rearranging so only
one version is needed.
* atlas ph sensor
- add select IRQ_WORK
* hmc8543 (soon to move out of staging)
- Comment style fixes
- functionality of suspend and resume was swapped.
* spear-adc
- use devm_clk_dev instead of managing the clk lifetime by hand.
Core
* Use new dmaengine_terminate_sync call to avoid a theoretical race.
* Fix docs for mlock in struct iio_dev as it is correctly taken in some
drivers (docs used to say for core only).
* Add a helper function for calculating the scan index storage size within
the core cutting out some cut and paste versions of the same code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=LIQe
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.6b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
2nd round of new IIO device support, features and cleanups for the 4.6 cycle.
New Device Support
* Apex stx104 DAC
- new driver for this PC104 board. Right now DAC support only.
* ADI ad5064
- Add support for ad5625, ad5627, ad5645, ad5665, ad5667 DACs.
- Add support for Linear Technology ltc2606, ltc2607, ltc2609, ltc2616,
ltc2617, ltc2619, ltc2626, ltc2627 and ltc2629.
* ADI ad7192
- add support for the ad7193
* Invensense mpu6050
- substantial rework of driver to use regmap allowing SPI support extending
the now split driver to cover the MPU6000.
* TI adc0832
- new driver supporting ADC0831, ADC0832, ADC0834 and ADC0838 ADCs.
* TI ads1015
- new driver, note that there is an existing hwmon driver. The long term
intention is to probably remove the hwmon driver but for now we just have
guards in place to ensure this driver is not built if that one is enabled.
* TI afe4403
- new driver for this heart rate monitor / pulse oximeter front end chip.
* TI afe4404
- new driver for this heart rate monitor / pulse oximeter front end chip.
Staging Graduations
* mxs-lradc
- A combined general purpose and touch screen (input) device driver.
Originally held in staging to allow reworking into and MFD but as
that wasn't happening and isn't an absolute requirement we are moving
it out of staging.
Driver new features
* ms5611
- triggered buffer support
- IIO_CHAN_INFO_SCALE to aid the triggered buffer support.
Driver cleanups / reworks / fixes
* ad5064
- Use an enum for the register map layout to allow support of additional
chips (precursor to the new support listed above).
- Structural driver changes to allow support of the slightly different
handling for the ltc parts above.
* ad5933
- drop an exceptional & unnecessary for a function pointer.
* ad7606
- Cleanup the repeated copies of pm ops.
- consolidate the various channels specs via a sport of rearranging so only
one version is needed.
* atlas ph sensor
- add select IRQ_WORK
* hmc8543 (soon to move out of staging)
- Comment style fixes
- functionality of suspend and resume was swapped.
* spear-adc
- use devm_clk_dev instead of managing the clk lifetime by hand.
Core
* Use new dmaengine_terminate_sync call to avoid a theoretical race.
* Fix docs for mlock in struct iio_dev as it is correctly taken in some
drivers (docs used to say for core only).
* Add a helper function for calculating the scan index storage size within
the core cutting out some cut and paste versions of the same code.
The driver has sysfs readings with runtime PM support for power saving.
It also offers buffer support that can be used together with IIO software
triggers.
Datasheet can be found here:
http://www.ti.com.cn/cn/lit/ds/symlink/ads1015.pdf
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Apex Embedded Systems STX104 is a 16-channel 16-bit analog input and
2-channel 16-bit analog output PC/104 card. The STX104 incorporates a
large one mega-sample FIFO.
This driver provides IIO support for the 2-channel DAC on the STX104.
The base port addresses for the devices may be configured via the "base"
module parameter array.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The only difference between the MPU6000 and the
MPU6050 is that the first also supports SPI.
Add SPI driver for this chip.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Separate this driver into core and i2c functionality.
This is in preparation for adding spi support.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use regmap instead of i2c specific functions.
This is in preparation of splitting this driver into core and
i2c specific functionality.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Acked-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The select/deselect_bypass duo writes the irq number into the interrupt
configuration register.
If there is a i2c slave device connected to the mpu (eg. a magnetometer)
then this can hinder interrupt delivery for the accelerometer and
gyroscope.
Set this register to the default configuration.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is a conversion queue driver for the mx25 SoC. It uses the central
ADC which is used by two seperate independent queues. This driver
prepares different conversion configurations for each possible input.
For a conversion it creates a conversionqueue of one item with the
correct configuration for the chosen channel. It then executes the queue
once and disables the conversion queue afterwards.
The reference voltages are configurable through devicetree subnodes,
depending on the connections of the ADC inputs.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds ADC0831/ADC0832/ADC0834/ADC0838 8-bit ADC driver.
I have tested with ADC0831 and ADC0832. The remaining ADC0834 and
ADC0838 are very similar to ADC0832.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The DMAengine framework gained support for synchronized transfer
termination. Use the new dmaengine_terminate_sync() function instead of
dmaengine_terminate_all(), this avoids a potential race condition when
disabling the buffer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The AD5625/AD5645/AD5665 are a family of 4 channel DACs with 12-bit, 14-bit
and 16-bit precision respectively. The devices come in 3 flavors in terms
of built-in reference, either no built-in reference, built-in 1.25V
reference or built-in 2.5V reference.
The AD5627/AD5647/AD5667 are similar to the AD5625/AD5645/AD5665 except
that they have 2 instead of 4 channels.
While these new devices are mostly register map compatible with the
existing devices support by the driver some offsets and register addresses
have been shuffled around. To accommodate this introduce a new register map
layout. For the lack of a better name we will just call it version 2.
Datasheets:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5625R_5645R_5665R_5625_5665.pdfhttp://www.analog.com/media/en/technical-documentation/data-sheets/AD5627R_5647R_5667R_5627_5667.pdf
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently the ad5064 only supports two different register map variations
and this is represented by a bool. This patch changes since to a enum so
we can support more variations in the future.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
List the newly support LTC devices in the Kconfig entry for the AD5064
driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Linear Technology LTC2606, LTC2607, LTC2609, LTC2616, LTC2617,
LTC2619, LTC2626, LTC2627 and LTC2629 devices are very similar
to the AD5064 device.
This patch adds support for those devices.
Datasheet for LTC devices:
LTC2606, LTC2616, LTC2626: http://www.linear.com/docs/6398
LTC2607, LTC2617, LTC2627: http://www.linear.com/docs/8977
LTC2709, LTC2619, LTC2629: http://www.linear.com/docs/8477
Signed-off-by: Marc Andre <marc.andre@netline.ch>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch makes minor structural changes to support specifics
for LTC2617 DAC. This DAC requires different handling of the
power down modes. The configuration to actually support the
DAC will be submitted in a secondary patch.
Adjust the DECLARE_AD5064_CHANNELS() macro to accept a new
ext_info parameter. This allows to use different power down
modes per DAC. (e.g. DAC only support 90kohm to ground)
Add the chip_info parameter "powerdown_ltc". This parameter is
used in the ad5064_sync_powerdown_mode() function to handle the
power down command for LTC diffently. For those devices the
power down command must be addressed to the channel.
Signed-off-by: Marc Andre <marc.andre@netline.ch>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add driver for the TI AFE4403 heart rate monitor and pulse oximeter.
This device detects reflected LED light fluctuations and presents an ADC
value to the user space for further signal processing.
Data sheet located here:
http://www.ti.com/product/AFE4403/datasheet
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add driver for the TI AFE4404 heart rate monitor and pulse oximeter.
This device detects reflected LED light fluctuations and presents an ADC
value to the user space for further signal processing.
Datasheet: http://www.ti.com/product/AFE4404/datasheet
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The newly added atlas-ph-sensor driver uses irq_work_queue, which
may not always be enabled:
ERROR: "irq_work_queue" [drivers/iio/chemical/atlas-ph-sensor.ko] undefined!
This adds a 'select' statement to Kconfig to ensure it's there
when we need it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 27dec00ecf ("iio: chemical: add Atlas pH-SM sensor support")
Reviewed-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We have the same code for computing the scan index storage size in bytes
all over the place. Factor this out into helper functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This will be used together with an external trigger (e.g hrtimer
based software trigger).
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This allows data exported via buffer interface to be converted
to standard units in userspace.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Device Support
* ad5761
- new driver
* at91_sama5d2 ADC.
- new driver and MAINTAINERS entry.
- minor cleanups followed.
* atlas pH-SM
- new driver (this has possibly the prettiest data sheet I've ever seen)
* mcp3422
- mcp3425 ADC added.
* mcp4725
- mcp4726 DAC added.
* mma8452
- mma8451q accelerometer added.
* mpl115
- mpl115a1 added (a lot bigger than it seems as this is an SPI part whereas
previous parts were i2c).
* si7005
- Hoperf th02 (seems to be a repackaged part)
* si7020
- Hoperf th06 (seems to be a repackaged part)
New features
* Core
- IIO_PH type. Does what it says on the tin.
* max30100
- LED current configuration support.
* mcp320x
- more differential measurement combinations.
* mma8452
- free fall deteciton
- opt3001
- enable operation without a IRQ line.
- device tree docs. Somehow the original docs have disappeared down
a rabbit hole, so here is a new set.
* st-sensors
- Support active-low interrupts.
Cleanups and minor / not so minor reworks
* Documentation
- drop some defunct ABI from the docs in staging.
* presure / Kconfig
- white space cleanup.
* ad7150
- BIT macro usage
- Alignment fixes
* ad7192
- false indent fixed.
* ak8975
- constify the ak_def structures
* axp288
- drop a redundant double const.
* dht11
- substantial reliability improvements by being more tolerant
of missing start bits.
- simplify the decoding algorithm
* mma8452
- whitespace cleanup
* mpl115
- don't bother setting i2c_client_data as nothing uses it.
* mpu6050
- drop unused function parameter.
* opt3001
- extract integration time as constants.
- trivial refactoring.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=fgTH
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new IIO device support, features and cleanups for the 4.6 cycle.
Device Support
* ad5761
- new driver
* at91_sama5d2 ADC.
- new driver and MAINTAINERS entry.
- minor cleanups followed.
* atlas pH-SM
- new driver (this has possibly the prettiest data sheet I've ever seen)
* mcp3422
- mcp3425 ADC added.
* mcp4725
- mcp4726 DAC added.
* mma8452
- mma8451q accelerometer added.
* mpl115
- mpl115a1 added (a lot bigger than it seems as this is an SPI part whereas
previous parts were i2c).
* si7005
- Hoperf th02 (seems to be a repackaged part)
* si7020
- Hoperf th06 (seems to be a repackaged part)
New features
* Core
- IIO_PH type. Does what it says on the tin.
* max30100
- LED current configuration support.
* mcp320x
- more differential measurement combinations.
* mma8452
- free fall deteciton
- opt3001
- enable operation without a IRQ line.
- device tree docs. Somehow the original docs have disappeared down
a rabbit hole, so here is a new set.
* st-sensors
- Support active-low interrupts.
Cleanups and minor / not so minor reworks
* Documentation
- drop some defunct ABI from the docs in staging.
* presure / Kconfig
- white space cleanup.
* ad7150
- BIT macro usage
- Alignment fixes
* ad7192
- false indent fixed.
* ak8975
- constify the ak_def structures
* axp288
- drop a redundant double const.
* dht11
- substantial reliability improvements by being more tolerant
of missing start bits.
- simplify the decoding algorithm
* mma8452
- whitespace cleanup
* mpl115
- don't bother setting i2c_client_data as nothing uses it.
* mpu6050
- drop unused function parameter.
* opt3001
- extract integration time as constants.
- trivial refactoring.
dependent on patches from the recent merge cycle.
* adc, imu and iio staging drivers
- !HAS_IOMEM dependency fixes
* dht11
- use boottime clock for time measurement to avoid incorrect measurements
due to clock updates.
* lidar
- correct a return value for short i2c transfers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=iF19
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.5b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 4.5 cycle. These ones are mostly
dependent on patches from the recent merge cycle.
* adc, imu and iio staging drivers
- !HAS_IOMEM dependency fixes
* dht11
- use boottime clock for time measurement to avoid incorrect measurements
due to clock updates.
* lidar
- correct a return value for short i2c transfers.
This set comprises those not dependent on patches in the 4.5 merge cycle.
A second set will follow shortly with ones that are.
* core in kernel interfaces
- fix a possible NULL dereference that is a theoretical possibility
via odd usage of iio_channel_release. Pretty much a hardening of
the interface, but observed in the wild with the twl4030_charger
driver.
* acpi-als
- report the data as processed as it is in lux. This fixes a wrong
use of the IIO ABI. However, old _raw version retained to avoid
breaking any userspace in the wild that is relying on that (none
known but it doesn't hurt us much to retain it)
* ade7753
- fix some error handling to avoid use of unitialized data.
* ltr501
- use a signed return type for ltr501_match_samp_freq so as to allow
returning of an error code.
* mcp4725
- set name field of struct iio_dev to ensure the sysfs name attribute
doesn't give NULL.
* mpl115
- temperature offset sign is wrong.
* stk8ba50
- IIO_TRIGGER dependency added
* ti_am335x_adc
- Label buffer as a software buffer. It's actually a hybrid of a
true hardware buffer feeding a kfifo, but the meaning of these fields
has changed a little recently and in this case it should be labeled
a software buffer ensure it is allowed to use the kfifo.
* vf610_adc
- HAS_IOMEM dependency
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=27Pv
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.5 cycle.
This set comprises those not dependent on patches in the 4.5 merge cycle.
A second set will follow shortly with ones that are.
* core in kernel interfaces
- fix a possible NULL dereference that is a theoretical possibility
via odd usage of iio_channel_release. Pretty much a hardening of
the interface, but observed in the wild with the twl4030_charger
driver.
* acpi-als
- report the data as processed as it is in lux. This fixes a wrong
use of the IIO ABI. However, old _raw version retained to avoid
breaking any userspace in the wild that is relying on that (none
known but it doesn't hurt us much to retain it)
* ade7753
- fix some error handling to avoid use of unitialized data.
* ltr501
- use a signed return type for ltr501_match_samp_freq so as to allow
returning of an error code.
* mcp4725
- set name field of struct iio_dev to ensure the sysfs name attribute
doesn't give NULL.
* mpl115
- temperature offset sign is wrong.
* stk8ba50
- IIO_TRIGGER dependency added
* ti_am335x_adc
- Label buffer as a software buffer. It's actually a hybrid of a
true hardware buffer feeding a kfifo, but the meaning of these fields
has changed a little recently and in this case it should be labeled
a software buffer ensure it is allowed to use the kfifo.
* vf610_adc
- HAS_IOMEM dependency
Wall time obtained from ktime_get_real_ns is susceptible to sudden jumps due to
user setting the time or due to NTP. Boot time is constantly increasing time
better suited for comparing two timestamps.
Signed-off-by: Abhilash Jindal <klock.android@gmail.com>
Reviewed-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Here are some small staging driver fixes for 4.5-rc2. One of them
predated 4.4-final, but I missed that merge window due to the holliday.
The others fix reported issues that have come up recently. The tty
change is needed for the speakup driver fix and has the ack of the tty
driver maintainer as well, i.e. myself :)
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlauWLoACgkQMUfUDdst+ynHbQCfWlGgQhtadfhtiaIKLwqy9NPG
PksAn3/z4mXX037sfm2kZrcqtcNlv9zf
=Vdai
-----END PGP SIGNATURE-----
Merge tag 'staging-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some small staging driver fixes for 4.5-rc2.
One of them predated 4.4-final, but I missed that merge window due to
the holliday. The others fix reported issues that have come up
recently. The tty change is needed for the speakup driver fix and has
the ack of the tty driver maintainer as well, i.e. myself :)
All have been in linux-next with no reported issues"
* tag 'staging-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Staging: speakup: fix read scrolled-back VT
Staging: speakup: Fix getting port information
Revert "Staging: panel: usleep_range is preferred over udelay"
iio: adis_buffer: Fix out-of-bounds memory access
The inv_check_and_setup_chip function does not use the i2c_device_id
parameter. Therefore remove it.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for the Atlas Scientific pH-SM chemical sensor that can
detect pH levels of solutions in the range of 0-14.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for Hoperf th06 humidity and
temperature sensor as it uses same register definitions
as si7020
th06 Datasheet: http://www.hoperf.com/upload/sensor/TH06.pdf
Signed-off-by: Cristina Moraru <cristina.moraru09@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for Hoperf th02 humidity and
temperature sensor as it uses same register definitions
as si7005
th02 Datasheet: http://www.anglia-live.com/netalogue/pdfs/hrf/datasheets/TH02_V1.1.pdf
Signed-off-by: Cristina Moraru <cristina.moraru09@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Clearly a high degree of cut and paste has gone on in this file, propogating
a particularly random combination of tabs and spaces. This patch at least
should make it all consistent going forward.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The new algorithm uses a 'one size fits em all' threshold, which should
be easier to understand and debug. I believe there are no regressions
compared to the old adaptive threshold algorithm. I don't remember why
I chose the old algorithm when I initially wrote the driver.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Instead of guessing where the data starts, we now just try to decode from
every possible start position. This causes no additional overhead if we
properly received the full preamble and only costs a few extra CPU cycles
in the case where the preamble is corrupted. This is much more efficient
than to return an error to userspace and start over again.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
mpl115 driver currently supports i2c interface (MPL115A2).
There is also SPI version (MPL115A1). The difference between them
is only physical transport so we can easily support both while sharing
most of the code.
Split the driver into a core support module and one module each for I2C
and SPI support.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
mpl115 sets i2c clientdata, but it is not used anywhere. So remove it.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Enable operation of the TI OPT3001 light sensor without having an
interrupt line available to connect the INT pin to.
In this operation mode, we issue a conversion request and simply wait
for the conversion time available as timeout value, determined from
integration time configuration and the worst-case time given in the data
sheet (sect. 6.5, table on p. 5):
short integration time (100ms): 110ms + 3ms = 113ms
long integration time (800ms): 880ms + 3ms = 883ms
This change is transparent as behaviour defaults to using the interrupt
method if an interrupt no. is configured via device tree. Interrupt-less
operation mode is performed when no valid interrupt no. is given.
Signed-off-by: Alexander Koch <mail@alexanderkoch.net>
Signed-off-by: Michael Hornung <mhornung.linux@gmail.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Change variable type of struct opt3001 members 'ok_to_ignore_lock' and
'result_ready' uint16-bitfield of length one to bool.
They are used as bool, let the compiler do the optimization.
Signed-off-by: Alexander Koch <mail@alexanderkoch.net>
Signed-off-by: Michael Hornung <mhornung.linux@gmail.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Extract integration times as #define constants. This prepares using them
for delay/timeout length determination.
Signed-off-by: Alexander Koch <mail@alexanderkoch.net>
Signed-off-by: Michael Hornung <mhornung.linux@gmail.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
According to the datasheet, the resolusion of temperature sensor is
-5.35 counts/C. Temperature ADC is 472 counts at 25C.
(https://www.sparkfun.com/datasheets/Sensors/Pressure/MPL115A1.pdf
NOTE: This is older revision, but this information is removed from the
latest datasheet from nxp somehow)
Temp [C] = (Tadc - 472) / -5.35 + 25
= (Tadc - 605.750000) * -0.186915888
So the correct offset is -605.750000.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Not every arch has io memory.
While the driver has correct dependencies the select statement
will bypass the HAS_IOMEM dependency.
So, unbreak the build by rendering it into a real dependency.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Not every arch has io memory.
So, unbreak the build by fixing the dependencies.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In twl4030_bci_probe() there are some failure paths where we call
iio_channel_release() with a NULL pointer. (Apparently, that driver can
opperate without a valid channel pointer). Let's fix it by adding a
NULL check in iio_channel_release().
Fixes: 2202e1fc5a ('drivers: power: twl4030_charger: fix link problems when building as module')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
ad5761 is a 1-channel DAC with configurable output range.
The driver uses the regulator interface for its voltage ref.
It shares its register layout with ad5761r, ad5721 and ad5721r.
Differences:
ad5761* are 16 bit, ad5721* are 12 bits.
ad57*1r have an internal reference.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
duplicate const can be removed, it is redundant. Found by static
analysis using smatch.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for this series' 14 bit accelerometer chip, MMA8451Q.
It's datasheet is available at the vendor's website:
https://cache.freescale.com/files/sensors/doc/data_sheet/MMA8451Q.pdf
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds freefall event detection to the supported devices. It adds
the in_accel_x&y&z_mag_falling_en iio event attribute, which activates
freefall mode.
In freefall mode, the current acceleration magnitude (AND combination
of all axis values) is compared to the specified threshold.
If it falls under the threshold (in_accel_mag_falling_value),
the appropriate IIO event code is generated.
This is what the sysfs "events" directory for these devices looks
like after this change:
-rw-r--r-- 4096 Oct 23 08:45 in_accel_mag_falling_period
-rw-r--r-- 4096 Oct 23 08:45 in_accel_mag_falling_value
-rw-r--r-- 4096 Oct 23 08:45 in_accel_mag_rising_period
-rw-r--r-- 4096 Oct 23 08:45 in_accel_mag_rising_value
-r--r--r-- 4096 Oct 23 08:45 in_accel_scale
-rw-r--r-- 4096 Oct 23 08:45 in_accel_x&y&z_mag_falling_en
-rw-r--r-- 4096 Oct 23 08:45 in_accel_x_mag_rising_en
-rw-r--r-- 4096 Oct 23 08:45 in_accel_y_mag_rising_en
-rw-r--r-- 4096 Oct 23 08:45 in_accel_z_mag_rising_en
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use var type for sizeof argument instead of the struct name.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
vref_uv has to be an int.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Merge third patch-bomb from Andrew Morton:
"I'm pretty much done for -rc1 now:
- the rest of MM, basically
- lib/ updates
- checkpatch, epoll, hfs, fatfs, ptrace, coredump, exit
- cpu_mask simplifications
- kexec, rapidio, MAINTAINERS etc, etc.
- more dma-mapping cleanups/simplifications from hch"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (109 commits)
MAINTAINERS: add/fix git URLs for various subsystems
mm: memcontrol: add "sock" to cgroup2 memory.stat
mm: memcontrol: basic memory statistics in cgroup2 memory controller
mm: memcontrol: do not uncharge old page in page cache replacement
Documentation: cgroup: add memory.swap.{current,max} description
mm: free swap cache aggressively if memcg swap is full
mm: vmscan: do not scan anon pages if memcg swap limit is hit
swap.h: move memcg related stuff to the end of the file
mm: memcontrol: replace mem_cgroup_lruvec_online with mem_cgroup_online
mm: vmscan: pass memcg to get_scan_count()
mm: memcontrol: charge swap to cgroup2
mm: memcontrol: clean up alloc, online, offline, free functions
mm: memcontrol: flatten struct cg_proto
mm: memcontrol: rein in the CONFIG space madness
net: drop tcp_memcontrol.c
mm: memcontrol: introduce CONFIG_MEMCG_LEGACY_KMEM
mm: memcontrol: allow to disable kmem accounting for cgroup2
mm: memcontrol: account "kmem" consumers in cgroup2 memory controller
mm: memcontrol: move kmem accounting code to CONFIG_MEMCG
mm: memcontrol: separate kmem code from legacy tcp accounting code
...
This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings several
of the more minor and older platforms we have closer to multiplatform
support. Among these are MMP, S3C64xx, Orion5x, mv78xx0 and realview
Much of this is moving around header files from old mach directories,
but there are also some cleanup patches of debug_ll (lowlevel debug
per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z1AW
-----END PGP SIGNATURE-----
Merge tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform code updates from Arnd Bergmann:
"This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings
several of the more minor and older platforms we have closer to
multiplatform support. Among these are MMP, S3C64xx, Orion5x, mv78xx0
and realview Much of this is moving around header files from old mach
directories, but there are also some cleanup patches of debug_ll
(lowlevel debug per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (75 commits)
ARM: realview: don't select SMP_ON_UP for UP builds
ARM: s3c: simplify s3c_irqwake_{e,}intallow definition
ARM: s3c64xx: fix pm-debug compilation
iio: exynos-adc: fix irqf_oneshot.cocci warnings
ARM: realview: build realview-dt SMP support only when used
ARM: realview: select apropriate targets
ARM: realview: clean up header files
ARM: realview: make all header files local
ARM: no longer make CPU targets visible separately
ARM: integrator: use explicit core module options
ARM: realview: enable multiplatform
ARM: make default platform work for NOMMU
ARM: debug-ll: move DEBUG_LL_UART_EFM32 to correct Kconfig location
ARM: defconfig: use correct debug_ll settings
ARM: versatile: convert to multi-platform
ARM: versatile: merge mach code into a single file
ARM: versatile: switch to DT only booting and remove legacy code
ARM: versatile: add DT based PCI detection
ARM: pxa: mark ezx structures as __maybe_unused
ARM: pxa: mark raumfeld init functions as __maybe_unused
...
Rewrite abs() so that its return type does not depend on the
architecture and no unexpected type conversion happen inside of it. The
only conversion is from unsigned to signed type. char is left as a
return type but treated as a signed type regradless of it's actual
signedness.
With the old version, int arguments were promoted to long and depending
on architecture a long argument might result in s64 or long return type
(which may or may not be the same).
This came after some back and forth with Nicolas. The current macro has
different return type (for the same input type) depending on
architecture which might be midly iritating.
An alternative version would promote to int like so:
#define abs(x) __abs_choose_expr(x, long long, \
__abs_choose_expr(x, long, \
__builtin_choose_expr( \
sizeof(x) <= sizeof(int), \
({ int __x = (x); __x<0?-__x:__x; }), \
((void)0))))
I have no preference but imagine Linus might. :] Nicolas argument against
is that promoting to int causes iconsistent behaviour:
int main(void) {
unsigned short a = 0, b = 1, c = a - b;
unsigned short d = abs(a - b);
unsigned short e = abs(c);
printf("%u %u\n", d, e); // prints: 1 65535
}
Then again, no sane person expects consistent behaviour from C integer
arithmetic. ;)
Note:
__builtin_types_compatible_p(unsigned char, char) is always false, and
__builtin_types_compatible_p(signed char, char) is also always false.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Whilst this part has a hardware buffer, the identifcation that IIO cares
about is the userspace facing end. It this case we push individual elements
from the hardware fifo into the software interface (specifically a kfifo)
rather than providing direct reads through to a hardware buffer
(as we still do in the sca3000 for example).
Technically the original specification as a hardware buffer could be
considered wrong, but it didn't matter until the patch listed below.
Result is that any attempt to enable the buffer will return -EINVAL
Fixes: 225d59adf1 ("iio: Specify supported modes for buffers")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
mcp320x driver supports the pseudo-differential mode by
in_voltage'IN+'-voltage'IN-'_raw where (IN+, IN-) = (0, 1), (2, 3), ...
mcp320x chips except MCP3X01 can also select swapped IN+ and IN-
pairs in the pseudo-differential mode.
i.e. in_voltage'IN+'-voltage'IN-'_raw where (IN+, IN-) = (1, 0),
(3, 2), ...
If the voltage level of IN+ is equal to or less than IN-, the
resultant code will be 000h. So it is useful to provide these, too.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Oskar Andero <oskar.andero@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
As per the ACPI specification (Revision 5.0) [1], the data coming
from the sensor represent the ambient light illuminance reading
expressed in lux. So use IIO_CHAN_INFO_PROCESSED to signify that
the data are pre-processed.
However, to keep backward ABI compatibility, the IIO_CHAN_INFO_RAW
bit is not removed.
[1] http://www.acpi.info/DOWNLOADS/ACPIspec50.pdf
This issue has also been responsible for at least one userspace bug
report hence marking what is a small semantic fix really for stable.
[2] https://github.com/hadess/iio-sensor-proxy/issues/46
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This driver supports the new version of the Atmel ADC device introduced
with the SAMA5D2 SoC family.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ak_def structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Most ST MEMS Sensors that support interrupts can also handle sending
an active low interrupt, i.e. going from high to low on data ready
(or other interrupt) and thus triggering on a falling edge to the
interrupt controller.
Set up logic to inspect the interrupt line we get for a sensor: if
it is triggering on rising edge, leave everything alone, but if it
triggers on falling edges, set up active low, and if unsupported
configurations appear: warn with errors and reconfigure the interrupt
to a rising edge, which all interrupt generating sensors support.
Create a local header for st_sensors_core.h to share functions
between the sensor core and the trigger setup code.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Without this change, the name entity for mcp4725 is missing in
/sys/bus/iio/devices/iio\:device*/name
With this change, name is reported correctly
Signed-off-by: Yong Li <sdliyong@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Ran into this on UML:
drivers/built-in.o: In function `vf610_adc_probe':
drivers/iio/adc/vf610_adc.c:744: undefined reference to `devm_ioremap_resource'
devm_ioremap_resource() is defined only when HAS_IOMEM is selected.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Ran into this on UML:
drivers/iio/accel/stk8ba50.c: In function ‘stk8ba50_data_rdy_trigger_set_state’:
drivers/iio/accel/stk8ba50.c:163:9: error: implicit declaration of function ‘iio_trigger_get_drvdata’ [-Werror=implicit-function-declaration]
iio_trigger_get_drvdata() is defined only when IIO_TRIGGER is selected.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Allow the current for both RED and IR LEDs to be set via an device tree
property setting.
This is an optional setting that is useful for applications that have a
known glass attenuation factor.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
lidar_i2c_xfer() function was never a non-positive value on error,
and this correct that with a -EIO return code.
Fixes: 366e65633c ("iio: proximity: lidar: optimize i2c transactions")
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
MCP4726 is a single channel 12-bit DAC. We can support MCP4726 with
a little changes to mcp4725 driver. In power-down mode, they have
different selection of VOUT pull-down registers.
MCP4726 also has features:
- Output gain options: 1x, 2x
- Voltage reference selection: VDD, VREF (Unbuffered or Buffered)
But these are not supported in this change. (1x gain, VDD is selected)
datasheet: http://ww1.microchip.com/downloads/en/DeviceDoc/22272C.pdf
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The MCP3425 is a single channel up to 16-bit A/D converter which has
features:
- On-Board Programmable Gain Amplifier (PGA):
- Gains of 1, 2, 4 or 8
- Programmable Data Rate Options:
- 15 SPS (16 bits), 60 SPS (14 bits), 240 SPS (12 bits)
The mcp3422 driver also supports the MCP3421 which is a single channel.
So we can support MCP3425 with a little changes to mcp3422 driver.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New driver features
- us5182
* Add interrupt support and rising / falling threshold events.
Cleanups / fixes to new stuff / minor additions
* Expose the IIO value formatting function for drivers to
make use of internally.
- ina2xx
* Fix wrong channel order
* Fix incorrect reporting of endianness
* Adding documentation of ABI unique to this device
- mma8452
* Drop an unused register description
* Use an enum for the channel index to aid readability
- sca3000
* Use standard NULL comparison style
- us5182
* fix an inconsistency in status of enable (a bug with no real effect until
above patches are applied)
* refactor the read_raw function to improve maintainability / readability.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=aiE2
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.5c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third set of new stuff for IIO in the 4.5 cycle.
New driver features
- us5182
* Add interrupt support and rising / falling threshold events.
Cleanups / fixes to new stuff / minor additions
* Expose the IIO value formatting function for drivers to
make use of internally.
- ina2xx
* Fix wrong channel order
* Fix incorrect reporting of endianness
* Adding documentation of ABI unique to this device
- mma8452
* Drop an unused register description
* Use an enum for the channel index to aid readability
- sca3000
* Use standard NULL comparison style
- us5182
* fix an inconsistency in status of enable (a bug with no real effect until
above patches are applied)
* refactor the read_raw function to improve maintainability / readability.
The big one here is the configfs support which has been a long time in the
works but should allow for cleaner ways to do instantiation of those elements
of IIO that aren't directly connected to specific hardware. Lots of cool new
stuff we can use this for in the works!
New core stuff (basically all configfs support related)
* Configfs support
- Core support (was waiting for a configfs patch that went in around 4.4rc2)
- A little fixlet to add a configfs.h to contain a reference to the
configfs_subsystem structure.
* Some infrastructure to simplify handling of software based triggers
(i.e. ones with no actual hardware associated with them)
* A high resolution timer based trigger. This has been around for years
but until the configfs support was ready we didn't have a sensible way
of instantiating instances of it (the method used for the sysfs_trigger
has never been really satisfactory)
New Device Support
* AMS iAQ Volatile Organic Compounds sensor support.
* Freescale imx7d ADC driver
* Maxim MAX30100 oximeter driver (note that for these devices most of the
smart stuff will be in userspace - effectively they are just light sensors
with some interesting led synchronization as far as the kernel is concerned).
* Microchip mcp3421 support added to the mcp3422 driver.
* TI adc124s021 support added to the adc128s052 driver.
* TI ina219, inda226 power monitors. Note that there is an existing hwmon driver
for these parts, the usecase is somewhat different so it is unclear at this
point if the hwmon driver will eventually be replaced by a bridge from
this driver. In the meantime the Kconfig dependencies should prevent both
from being built.
New driver functionality
* us8152d power management support.
Cleanups, fixups
* Use list_for_each_entry_safe instead of list_for_each_safe with the entry
bit coded longhand.
* Select IRQ_WORK for IIO_DUMMY_EVGEN. This is a fix that somehow got lost
when the driver was moved so lets do it again.
* st-accel - drop an unused define.
* vz89x, lidar - optimize i2c transactions by using a single i2c tranfers
instead of multiple calls where supported (fall back to smbus calls as
before if not).
* Use dev_get_platdata() in staging drivers: tsl2x7x, adcs and frequency
drivers instead of direct access to the structure element.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=54PR
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.5b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new drivers, functionality and cleanups for the 4.5 cycle.
The big one here is the configfs support which has been a long time in the
works but should allow for cleaner ways to do instantiation of those elements
of IIO that aren't directly connected to specific hardware. Lots of cool new
stuff we can use this for in the works!
New core stuff (basically all configfs support related)
* Configfs support
- Core support (was waiting for a configfs patch that went in around 4.4rc2)
- A little fixlet to add a configfs.h to contain a reference to the
configfs_subsystem structure.
* Some infrastructure to simplify handling of software based triggers
(i.e. ones with no actual hardware associated with them)
* A high resolution timer based trigger. This has been around for years
but until the configfs support was ready we didn't have a sensible way
of instantiating instances of it (the method used for the sysfs_trigger
has never been really satisfactory)
New Device Support
* AMS iAQ Volatile Organic Compounds sensor support.
* Freescale imx7d ADC driver
* Maxim MAX30100 oximeter driver (note that for these devices most of the
smart stuff will be in userspace - effectively they are just light sensors
with some interesting led synchronization as far as the kernel is concerned).
* Microchip mcp3421 support added to the mcp3422 driver.
* TI adc124s021 support added to the adc128s052 driver.
* TI ina219, inda226 power monitors. Note that there is an existing hwmon driver
for these parts, the usecase is somewhat different so it is unclear at this
point if the hwmon driver will eventually be replaced by a bridge from
this driver. In the meantime the Kconfig dependencies should prevent both
from being built.
New driver functionality
* us8152d power management support.
Cleanups, fixups
* Use list_for_each_entry_safe instead of list_for_each_safe with the entry
bit coded longhand.
* Select IRQ_WORK for IIO_DUMMY_EVGEN. This is a fix that somehow got lost
when the driver was moved so lets do it again.
* st-accel - drop an unused define.
* vz89x, lidar - optimize i2c transactions by using a single i2c tranfers
instead of multiple calls where supported (fall back to smbus calls as
before if not).
* Use dev_get_platdata() in staging drivers: tsl2x7x, adcs and frequency
drivers instead of direct access to the structure element.
This was extracted from a reposting of the driver after it had been applied
to the IIO tree. I have fast tracked it as the driver will be in 4.5 and
it would be nice to fix this trivial issue before it is.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A bit of refactoring for better readability.
Moved and slightly reorganized all the activity necessary for reading als
and proximity into a different function. This way the switch in read raw
becomes clearer and more compact.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Crestez Dan Leonard