While testing scsi_debug with these patches I found a
problem with the Block Limits VPD page function. The
length returned by the inquiry_evpd_b0() function was
too short. A patch to fix that and a cosmetic change
(that the form factor of scsi_debug is less than 1.8
inches) is attached.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This version fixes 64-bit modulo on 32-bit as well as inadvertent map
updates when TP was disabled.
Implement support for thin provisioning in scsi_debug. No actual memory
de-allocation is taking place. The intent is to emulate a thinly
provisioned storage device, not to be one.
There are four new module options:
- unmap_granularity specifies the granularity at which to track mapped
blocks (specified in number of logical blocks). 2048 (1 MB) is a
realistic value for disk arrays although some may have a finer
granularity.
- unmap_alignment specifies the first LBA which is naturally aligned on
an unmap_granularity boundary.
- unmap_max_desc specifies the maximum number of ranges that can be
unmapped using one UNMAP command. If this is 0, only WRITE SAME is
supported and UNMAP will cause a check condition.
- unmap_max_blocks specifies the maximum number of blocks that can be
unmapped using a single UNMAP command. Default is 0xffffffff.
These parameters are reported in the new and extended block limits VPD.
If unmap_granularity is specified the device is tagged as thin
provisioning capable in READ CAPACITY(16). A bitmap is allocated to
track whether blocks are mapped or not. A WRITE request will cause a
block to be mapped. So will WRITE SAME unless the UNMAP bit is set.
Blocks can be unmapped using either WRITE SAME or UNMAP. No accounting
is done to track partial blocks. This means that only whole blocks will
be marked free. This is how the array people tell me their firmwares
work.
GET LBA STATUS is also supported. This command reports whether a block
is mapped or not, and how long the adjoining mapped/unmapped extent is.
The block allocation bitmap can also be viewed from user space via:
/sys/bus/pseudo/drivers/scsi_debug/map
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add support for 32-byte READ/WRITE as well as DIF Type 2 protection.
Reject protected 10/12/16 byte READ/WRITE commands when Type 2 is
enabled.
Verify Type 2 reference tag according to Expected Initial LBA in 32-byte
CDB.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch adds support for setting the physical block exponent and
lowest aligned LBA in the READ CAPACITY(16) response.
The B0 VPD page is adjusted accordingly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds support for DIX and DIF in scsi_debug. A separate
buffer is allocated for the protection information.
- The dix parameter indicates whether the controller supports DIX
(protection information DMA)
- The dif parameter indicates whether the simulated storage device
supports DIF
- The guard parameter switches between T10 CRC(0) and IP checksum(1)
- The ato parameter indicates whether the application tag is owned by
the disk(0) or the OS(1)
- DIF and DIX errors can be triggered using the scsi_debug_opts mask
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
[jejb: limit ioctl to returning 20 characters to avoid overrun
on long device names and add a few more conversions]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
[jejb: fixed up a ton of missed conversions.
All of you are on notice this has happened, driver trees will now
need to be rebased]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: SCSI List <linux-scsi@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add support for VPD page b1 to scsi_debug
SCSI VPD page b1 reports the nominal rotation speed of the device.
Since scsi_debug is ram-based, claim to be a non-rotating medium.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Make scsi_debug sector size configurable at load time instead of being
a #define. Handy for testing 4KB sectors.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We can save some atomic ops in the IO path, if we clearly define
the rules of how to modify the queue flags.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch removes function declarations with moving some
functions. This cleans up them a bit to silence checkpatch.pl. There
is no functional change.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently, the maximum amount of RAM that scsi_debug can allocate is
4GB. This patch increases it to 2TB; scsi_debug can allocates 2TB
memory and export it as if it were 2TB scsi disk.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
resp_read and resp_write performs READ_* and WRITE_* commands
respectively. This sweeps up the similar code in them.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sdebug_capacity is calculated at five different places. This add a
helper function to calculate sdebug_capacity to sweep up the
duplicatated code.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sdebug_store_size doesn't need to be static global. It's used at
startup only.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch removes lots of function declarations with moving
scsi_debug_queuecommand. This cleans up scsi_debug_queuecommand a bit
to silence checkpatch.pl
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces list_for_each_safe and list_entry with
list_for_each_entry_safe.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
open_devip is always non NULL.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Two functions, sdebug_add_adapter and devInfoReg, creates new
scsi_debug devices. To simplify the code, this patch adds a new helper
function to create new scsi_debug devices (sdebug_device_create) and
converts both functions to use it.
I plan to add more to scsi_debug devices (e.g. using a thread for a
scsi_debug device for scalability testings). This patch enable me to
add such to just the new helper function instead of touching two
functions, sdebug_add_adapter and devInfoReg.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi_debug.h just incldues some function declarations. This patch removes it
with moving the scsi_host_template.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This converts scsi_debug to include header files in include/scsi/
instead of drivers/scsi/scsi.h.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Lots of drivers set it to 0. Remove that. Patch should be a nop.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi_debug does at several places:
for_each_sg(sdb->table.sgl, sg, sdb->table.nents, k) {
kaddr = (unsigned char *)
kmap_atomic(sg_page(sg), KM_USER0);
We cannot do something like that with the clustering enabled (or we
can use scsi_kmap_atomic_sg).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This enables fill_from_dev_buffer and fetch_to_dev_buffer to handle
bidi commands.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds get_data_transfer_info helper function that get lha and
sectors for READ_* and WRITE_* commands (and XDWRITEREAD_10 later).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
collapsed with fw-sbp2 patch "Drop cast to non-const char * in host
template initialization." from Kristian Høgsberg
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Correct the module info text for the default value of
"every_nth" to 0.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After discussions in the thread titled:
[PATCH] scsi_debug: illegal blocking memory allocation
here is a patch containing the discussed fix and some other
fixes and additions. The patch is against lk 2.6.20-rc3 .
The version is bumped to 1.81 .
ChangeLog:
- Change several GFP_KERNEL allocations to GFP_ATOMIC
as they can be called from queuecommand() context
- check above allocation returns and if out of memory
report DID_REQUEUE in two cases, DID_NO_CONNECT in
another, and fail slave configure() in another
- add support for WRITE BUFFER command
- add aborted_command error injection support
(opts mask 0x10), similar mechanism to
recovered_error injection.
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds support for REPORT TARGET PORT GROUPS. This is used
eg for the multipathing priority callout to determine the path
priority.
With this patch multipath-tools can use the existing mpath_prio_alua
callout to exercise the path priority grouping.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
See http://www.torque.net/sg/sdebug26.html for more
information on the scsi_debug driver.
ChangeLog:
- add 'vpd_use_hostno' parameter to allow simulated hosts
to see the same set of targets (and luns). For testing
multipath software.
- add 'fake_rw' parameter to ignore the data in READ and
WRITE commands
- add support for log subpages (new in SPC-4)
- yield appropriate block descriptor for MODE SENSE
commands (only for pdt=0 (i.e. disks))
- REQUEST SENSE response no longer shows the stopped
power condition (SAT changed to agree with SPC-3)
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Check all __must_check warnings in scsi_debug.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/nsp32.c
drivers/scsi/pcmcia/nsp_cs.c
Removal of randomness flag conflicts with SA_ -> IRQF_ global
replacement.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- add 'virtual_gb' parameter to simulate large storage
(by wrapping in dev_size_mb megabytes of actual ram)
- add 'no_lun_0' parameter to skip lun 0 on each target
(but still respond as required to INQUIRY + REPORT LUNS)
- add well know lu support
- add MODE SELECT commands support [pages: 0xa and 0x1c]
- add LOG SENSE command support [pages: 0xd and 0x2f]
- add READ CAPACITY (16) support
- increase number of mode pages supported (to read),
mainly transport specific (SAS) mode (sub)pages
- add more VPD pages and extend others, including
ATA information VPD page
- START STOP UNIT now maintains a state machine
- READ (16) and WRITE (16) cope with lbas larger
than 32 bits (needed for the 'virtual_gb' parameter)
- allow single command transfers up to 32 MB
- more precise error (sense data) messages
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Change the core SCSI code to use kzalloc rather than kmalloc+memset
where possible.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Douglas Gilbert