of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Timur Tabi <timur@tabi.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 343fda9548 ("serial: mxs-auart: properly handle mctrl_gpio
failing") introduced the following build error:
CC drivers/tty/serial/mxs-auart.o
drivers/tty/serial/mxs-auart.c: In function 'mxs_auart_probe':
drivers/tty/serial/mxs-auart.c:1282:3: error: unknown type name 'got'
Fix it by providing a proper return code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If mctrl_gpio_init returns an error code this value should be forwarded and
the driver must not simply ignore this failure.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to explicitly zero the 'ret' variable as it is properly
initialized in a few lines below as:
ret = serial_mxs_probe_dt(s, pdev);
Remove the unneeded zeroing of 'ret'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should check whether platform_get_irq() failed, and in the case of error
this needs to be propagated.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The irq number is only used inside the probe function, so there is no need
to keep it in the private mxs_auart_port structure.
Use a local 'irq' variable for storing the irq number instead.
Also make its type of 'int' as platform_get_irq() may fail and return a
negative number.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By using devm_request_irq() we can have a shorter and cleaner code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By using devm_clk_get() we can have a shorter and cleaner code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By using devm_kzalloc() we can have a shorter and cleaner code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of jumping to the 'out' label, let's return the error immediately, which
makes the code shorter and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
tx_empty() should test whether both the transmitter fifo and shifter
for the port is empty, ie. the whole last char was transmitted.
The shift register is empty if AUART_STAT_BUSY is cleared.
The patch fixes the function against the shift register.
According to i.MX23 and i.MX28 Reference Manual:
AUART_STAT_TXFE:
TX FIFO or transmit holding register is empty.
AUART_STAT_BUSY:
AUART still transmits bits.
The BUSY signal goes HIGH as soon as the data is written to the
transmit FIFO (that is, the FIFO is non-empty) and remains asserted
HIGH while data is being transmitted.
BUSY is negated only when the transmit FIFO is empty, and the last
character has been transmitted from the shift register, including
the stop bits.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mxs_auart_modem_status() did't detect gpio's state change
because s->mctrl_prev was modified before by mctrl_gpio_get().
The patch introduces mctrl_temp variable to fix the bug.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 732a84a037 ("serial: core: Pass termios to set_ldisc() notifications")
changed the set_ldisc prototype.
At the time of this commit the mxs_auart driver did not implement set_ldisc,
so that's why it has not been converted.
Adapt also mxs_auart_set_ldisc() so that the following build warning can be
fixed:
drivers/tty/serial/mxs-auart.c:962:2: warning: initialization from
incompatible pointer type
.set_ldisc = mxs_auart_set_ldisc,
^
drivers/tty/serial/mxs-auart.c:962:2: warning: (near initialization
for 'mxs_auart_ops.set_ldisc')
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enables PPS support in mxs-auart serial driver to make PPS API working.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dedicated CTS and RTS pins are unusable together with a lot of other
peripherals because they share the same line. Pinctrl is limited.
Moreover, the AUART controller doesn't handle DTR/DSR/DCD/RI signals,
so we have to control them via GPIO.
This patch permits to use GPIOs to control the CTS/RTS/DTR/DSR/DCD/RI
signals.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Reviewed-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King:
The only thing which the .get_mctrl method is supposed to do is
to return the state of the /input/ lines, which are CTS, DCD, DSR, RI.
The output line state is stored in port->mctrl, and is added to
the returned value by serial_core when it's required.
RTS output state should not be returned from the .get_mctrl method.
This patch removes ctrl variable from mxs_auart_port
and removes useless reading back RTS line.
The ctrl variable in mxs_auart_port duplicated mctrl,
member of uart_port structure in serial_core.h.
The removed code from mxs_auart_set_mctrl() and mxs_auart_get_mctrl
duplicated uart_update_mctrl() and uart_tiocmget()
in serial_core.c.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Reviewed-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using mxs-auart based console, sometime we need the sysrq function
to help debugging kernel. The sysrq code is basically there,
this patch just simply enable it.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core uses the tty port flags, ASYNC_CTS_FLOW and
ASYNC_CD_CHECK, to track whether CTS and DCD changes should be
ignored or handled. However, the tty port flags are not safe for
atomic bit operations and no lock provides serialized updates.
Introduce the struct uart_port status field to track CTS and DCD
enable states, and serialize access with uart port lock. Substitute
uart_cts_enabled() helper for tty_port_cts_enabled().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If IGNBRK is set without either BRKINT or PARMRK set, some uart
drivers send a 0x00 byte for BREAK without the TTYBREAK flag to the
line discipline, when it should send either nothing or the TTYBREAK flag
set. This happens because the read_status_mask masks out the BI
condition, which uart_insert_char() then interprets as a normal 0x00 byte.
SUS v3 is clear regarding the meaning of IGNBRK; Section 11.2.2, General
Terminal Interface - Input Modes, states:
"If IGNBRK is set, a break condition detected on input shall be ignored;
that is, not put on the input queue and therefore not read by any
process."
Fix read_status_mask to include the BI bit if IGNBRK is set; the
lsr status retains the BI bit if a BREAK is recv'd, which is
subsequently ignored in uart_insert_char() when masked with the
ignore_status_mask.
Affected drivers:
8250 - all
serial_txx9
mfd
amba-pl010
amba-pl011
atmel_serial
bfin_uart
dz
ip22zilog
max310x
mxs-auart
netx-serial
pnx8xxx_uart
pxa
sb1250-duart
sccnxp
serial_ks8695
sirfsoc_uart
st-asc
vr41xx_siu
zs
sunzilog
fsl_lpuart
sunsab
ucc_uart
bcm63xx_uart
sunsu
efm32-uart
pmac_zilog
mpsc
msm_serial
m32r_sio
Unaffected drivers:
omap-serial
rp2
sa1100
imx
icom
Annotated for fixes:
altera_uart
mcf
Drivers without break detection:
21285
xilinx-uartps
altera_jtaguart
apbuart
arc-uart
clps711x
max3100
uartlite
msm_serial_hs
nwpserial
lantiq
vt8500_serial
Unknown:
samsung
mpc52xx_uart
bfin_sport_uart
cpm_uart/core
Fixes: Bugzilla #71651, '8250_core.c incorrectly handles IGNBRK flag'
Reported-by: Ivan <athlon_@mail.ru>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DMA is enabled (with hardware flow control enabled) the FIFO size
must be set to the size of the DMA buffer, as this is the size the tty
subsystem can use.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MXS_AUART_DMA_CONFIG is originally used to check if the DT node
is configured with the DMA property.
But now, the MXS_AUART_DMA_CONFIG is set unconditionally in the
serial_mxs_probe_dt(), so the check in the mxs_auart_settermios() is
not necessary anymore. This patch removes this macro.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original DMA support works only when RTS/CTS is enabled.
(see the "e800163 serial: mxs-auart: add the DMA support for mx28")
But after several patches, DMA support has lost this limit.
(see the "bcc20f9 serial: mxs-auart: move to use generic DMA helper")
So an UART without the RTS/CTS lines may also enables the DMA support,
in which case the UART may gets unpredictable results.
This patch adds an optional property for the UART DT node
which indicates the UART has RTS and CTS lines, and it also means you
enable the DMA support for this UART.
This patch also adds a macro MXS_AUART_RTSCTS, and uses it to check
RTS/CTS before we enable the DMA for the UART.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this patch the driver waits ~1 ms for the UART to become idle. At
115200n8 this time is (theoretically) enough to transfer 11.5 characters
(= 115200 bits/s / (10 Bits/char) * 1ms). As the mxs-auart has a fifo size
of 16 characters the clock is gated too early. The problem is worse for
lower baud rates.
This only happens to really shut down the transmitter in the middle of a
transfer if /dev/ttyAPPx isn't opened in userspace (e.g. by a getty) but
was at least once (because the bootloader doesn't disable the transmitter).
So increase the timeout to 20 ms which should be enough for 9600n8, too.
Moreover skip gating the clock if the timeout is elapsed.
Cc: stable@vger.kernel.org # v2.6.39+
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The handler needs to ack the pending events before actually handling them.
Otherwise a new event might come in after it it considered non-pending or
handled and is acked then without being handled. So this event is only
noticed when the next interrupt happens.
Without this patch an i.MX28 based machine running an rt-patched kernel
regularly hangs during boot.
Cc: stable@vger.kernel.org # v2.6.39+
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These are mostly new device tree bindings for existing drivers, as well
as changes to the device tree source files to add support for those
devices, and a couple of new boards, most notably Samsung's Exynos5
based Chromebook.
The changes depend on earlier platform specific updates and touch
the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G60S
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.
The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."
* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...
Driver core already takes care of refcounting, no need to do this on
driver level again.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the generic DMA device tree helper supported by mxs-dma driver,
client devices only need to call dma_request_slave_channel() for
requesting a DMA channel from dmaengine.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_string this time.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Detected by cppcheck:
[others/linux/drivers/tty/serial/mxs-auart.c:553]: (style) Same expression on both sides of '||'.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following warning when building with W=1 option:
drivers/tty/serial/mxs-auart.c: In function 'mxs_auart_tx_chars':
drivers/tty/serial/mxs-auart.c:272:10: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the patch "serial: mxs-auart: fix the wrong RTS hardware flow control" the
mainline mxs-uart driver now sets RTSEN only when hardware flow control is
enabled via software. It is not possible any longer to set RTS manually via
software. However, the manual modification is a valid operation.
Regain the possibility to set RTS via software and only set RTSEN when hardware
flow control is explicitly enabled via settermios cflag CRTSCTS.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should first unmap the DMA scatter list for receiving data, and
then copy the data from the DMA buffer.
The old code misses unmap the scatter list for RX. This patch fixes it.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Tested-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the DMA is enabled, the Receive Timeout interrupt is very easy to be arised
in the 3M baud rate. The interrupt handler (aka mxs_auart_irq_handle) will call
mxs_auart_rx_chars() to handle the received data. This is not right, we can not
get the correct data from the RXFIFO now, the data have been moved to the
DMA buffer by the DMA engine.
This patch
(1) disables the Receive Timeout Interrupt when the DMA is enabled,
(2) and invoke the mxs_auart_rx_chars() only when the DMA is not enabled.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Tested-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only we meet the following conditions, we can enable the DMA support for
auart:
(1) We enable the DMA support in the dts file, such as
arch/arm/boot/dts/imx28.dtsi.
(2) We enable the hardware flow control.
(3) We use the mx28, not the mx23. Due to hardware bug(see errata: 2836),
we can not add the DMA support to mx23.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current mxs-auart driver is used for both mx23 and mx28.
But in mx23, the DMA has a bug(see errata:2836). We can not add the
DMA support in mx23, but we can add DMA support to auart in mx28.
So in order to add the DMA support for the auart in mx28, we should
distinguish the distinguish SOCs.
This patch adds a new platform_device_id table and a inline function
is_imx28_auart() to distinguish the mx23 and mx28.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mxs_auart_probe() gets the device by the get_device().
So we should put the device in the error path to balance the
device's reference counter.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fabian Frederick