Since we need multiple components for I915 for different purposes
(Audio & Mei_hdcp), we adopt the subcomponents methodology introduced
by the previous patch (mentioned below).
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Jan 28 17:08:20 2019 +0530
components: multiple components for a device
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by-by: Ramalingam C <ramalinagm.c@intel.com> (commit message)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (code)
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Russell King <rmk+kernel@arm.linux.org.uk>
cc: Rafael J. Wysocki <rafael@kernel.org>
cc: Jaroslav Kysela <perex@perex.cz>
cc: Takashi Iwai <tiwai@suse.com>
cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
cc: Jani Nikula <jani.nikula@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190207232759.14553-4-daniel.vetter@ffwll.ch
Platforms having multiple SORs and hdmi/dp sinks require higher
bandwidth to support simultaneous playbacks of higher resolution.
If hda controller supports multiple SDO lines, STRIPE can be used
to indicate how many of the SDO lines the stream should be striped
across.
During stream start stripe control bits are programmed to use given
number of sdo lines and the same is cleared during stream stop.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Mohan Kumar D <mkumard@nvidia.com>
Reviewed-by: Ravindra Lokhande <rlokhande@nvidia.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Controllers and codecs can support striping of audio out across
multiple SDO lines. The number of supported SDO lines can be
specific to chip. GCAP register can be read to know the maximum
supported SDO lines.
snd_hdac_get_stream_stripe_ctl() is exposed to program stripe bits
on controller and codec side.
stripe value: 0 for 1SDO, 1 for 2SDO, 2 for 4SDO lines, etc.,
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Mohan Kumar D <mkumard@nvidia.com>
Reviewed-by: Ravindra Lokhande <rlokhande@nvidia.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To enable SIE(Stream Interrupt Enable) in snd_hdac_stream_start(), we
should set both mask and value to be "1 << azx_dev->index" for register
update, the mask was 0, here fix it.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
E.g. for azx_int_enable(), we should set both mask and value to be
"AZX_INT_CTRL_EN | AZX_INT_GLOBAL_EN"(the mask was 0) to enable
controller CIE and GIE.
We have similar issues on setting AZX_GCTL_RESET and AZX_GCTL_UNSOL,
here try to correct all of them.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The SOF implementation does not rely on the hdac_bus library, however
for HDMI and HDaudio codec support it does need to deal with
unsolicited events. Instead of re-inventing the wheel, export this
symbol to reuse this part of the library directly.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After the recent refactoring, snd_hdac_display_power() doesn't return
any error, hence it can be defined to return void.
This makes many error checks redundant and allows us to reduce them
gracefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current HD-audio code manages the DRM audio power via too complex
redirections, and this seems even still unbalanced in a corner case as
Intel DRM CI has been intermittently reporting. This patch is a big
surgery for addressing the complexity and the possible unbalance.
Basically the patch changes the display PM in the following ways:
- Both HD-audio controller and codec drivers call a single helper,
snd_hdac_display_power(). (Formerly, the display power control from
a codec was done indirectly via link_power bus ops.)
- snd_hdac_display_power() receives the codec address index. For
turning on/off from the controller, pass HDA_CODEC_IDX_CONTROLLER.
- snd_hdac_display_power() doesn't manage refcounts any longer, but
keeps the power status in bitmap. If any of controller or codecs is
turned on, the function updates the DRM power state via get_power()
or put_power().
Also this refactor allows us more cleanup:
- The link_power bus ops is dropped, so there is no longer indirect
management, as mentioned in the above.
- hdac_device link_power_control flag is moved to hda_codec
display_power_control flag, as it's only for HDA legacy.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106525
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There have been little changes in ALSA core stuff, but ASoC core still
kept rolling for the continued restructuring. The rest are lots of
small driver-specific changes and some minor API updates.
Here are highlights:
General:
- Appropriate fall-through annotations everywhere
- Some code cleanup in memalloc code, handling non-cacahed pages more
commonly in the helper
- Deployment of SNDRV_PCM_INFO_SYNC_APPLPTR flag consistently
Drivers:
- More HD-audio CA0132 codec improvement for supporting other Creative
boards
- Plumbing legacy HD-audio codecs as ASoC BE on Intel SST; this will
give move support of existing HD-audio devices with DSP
- A few device-specific HD-audio quirks as usual
- New quirk for RME CC devices and correction for B&W PX for USB-audio
- FireWire: code refactoring including devres usages
ASoC Core:
- Continued componentization works; it's almost done!
- A bunch of new for_each_foo macros
- Cleanups and fixes in DAPM code
ASoC Drivers:
- MCLK support for several different devices, including CS42L51, STM32
SAI, and MAX98373
- Support for Allwinner A64 CODEC analog, Intel boards with DA7219 and
MAX98927, Meson AXG PDM inputs, Nuvoton NAU8822, Renesas R8A7744 and
TI PCM3060
-----BEGIN PGP SIGNATURE-----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=3LrT
-----END PGP SIGNATURE-----
Merge tag 'sound-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There have been little changes in ALSA core stuff, but ASoC core still
kept rolling for the continued restructuring. The rest are lots of
small driver-specific changes and some minor API updates. Here are
highlights:
General:
- Appropriate fall-through annotations everywhere
- Some code cleanup in memalloc code, handling non-cacahed pages more
commonly in the helper
- Deployment of SNDRV_PCM_INFO_SYNC_APPLPTR flag consistently
Drivers:
- More HD-audio CA0132 codec improvement for supporting other Creative
boards
- Plumbing legacy HD-audio codecs as ASoC BE on Intel SST; this will
give move support of existing HD-audio devices with DSP
- A few device-specific HD-audio quirks as usual
- New quirk for RME CC devices and correction for B&W PX for USB-audio
- FireWire: code refactoring including devres usages
ASoC Core:
- Continued componentization works; it's almost done!
- A bunch of new for_each_foo macros
- Cleanups and fixes in DAPM code
ASoC Drivers:
- MCLK support for several different devices, including CS42L51, STM32
SAI, and MAX98373
- Support for Allwinner A64 CODEC analog, Intel boards with DA7219 and
MAX98927, Meson AXG PDM inputs, Nuvoton NAU8822, Renesas R8A7744 and
TI PCM3060"
* tag 'sound-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (299 commits)
ASoC: stm32: sai: fix master clock naming
ASoC: stm32: add clock dependency for sai
ALSA: hda/ca0132 - Actually fix microphone issue
ASoC: sun4i-i2s: move code from startup/shutdown hooks into pm_runtime hooks
ASoC: wm2000: Remove wm2000_read helper function
ASoC: cs42l51: fix mclk support
ASoC: wm_adsp: Log addresses as 8 digits in wm_adsp_buffer_populate
ASoC: wm_adsp: Rename memory fields in wm_adsp_buffer
ASoC: cs42l51: add mclk support
ASoC: stm32: sai: set sai as mclk clock provider
ASoC: dt-bindings: add mclk support to cs42l51
ASoC: dt-bindings: add mclk provider support to stm32 sai
ASoC: soc-core: fix trivial checkpatch issues
ASoC: dapm: Add support for hw_free on CODEC to CODEC links
ASoC: Intel: kbl_da7219_max98927: minor white space clean up
ALSA: i2c/cs8427: Fix int to char conversion
ALSA: doc: Brush up the old writing-an-alsa-driver
ASoC: rsnd: tidyup SSICR::SWSP for TDM
ASoC: rsnd: enable TDM settings for SSI parent
ASoC: pcm3168a: add hw constraint for capture channel
...
E.g. for snd_hdac_ext_bus_link_power_up(), we should set mask to be
AZX_MLCTL_SPA(it was 0), and AZX_MLCTL_SPA as value to power up it,
here correct it and several similar mismatches.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The timeout of audio component binding was incorrectly specified in
msec, not in jiffies, which results in way too shorter timeout than
expected.
Along with fixing it, add the information print about the binding
failure to show the unexpected situation more clearly.
Fixes: a57942bfdd ("ALSA: hda: Make audio component support more generic")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is the usual set of small fixes scatterd around various drivers,
plus one fix for DAPM and a UAPI build fix. There's not a huge amount
that stands out here relative to anything else.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAluf2AQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0BojB/9ZpiRgSSjKTFSmGgu3OFI7Nvj63ruB
hxOnwOc8Bea8tZtpzgEcx/aLZ1sbWVT4uRUYZv0Tf6UJtuOQagbJDEUkUdRitKtX
1khSMyKFlAa7cIbv19ZOMCN0pjcs7hlHCPryT8AyCWCWN8yPdlUsDqWfyfUoq56r
qpdu/OQ4E9VvS8OcX1gPjcop3gE/fYEoU+mbUpr0KYUXaroEzJm85tOqpGYk4+XW
GCNUR19vNRJr5G6ANqIx96JOlgF5nRZu7aOfvLceiWH5BgPdW3iNRAJkPmKCIHwb
a1+X21eCC7Ec2/7bQmR5Aoxz1yqzhngrevSFNLrqXFZmMmNrEfkfdCrJ
=gVzO
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.19
This is the usual set of small fixes scatterd around various drivers,
plus one fix for DAPM and a UAPI build fix. There's not a huge amount
that stands out here relative to anything else.
Internally, skl_init_chip() calls snd_hdac_bus_init_chip() which
1) sets bus->chip_init to prevent multiple entrances before device
is stopped; 2) enables interrupt.
We shouldn't use it for the purpose of resetting device only because
1) when we really want to initialize device, we won't be able to do
so; 2) we are ready to handle interrupt yet, and kernel crashes when
interrupt comes in.
Rename azx_reset() to snd_hdac_bus_reset_link(), and use it to reset
device properly.
Fixes: 60767abcea ("ASoC: Intel: Skylake: Reset the controller in probe")
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In snd_hdac_bus_init_chip(), we enable interrupt before
snd_hdac_bus_init_cmd_io() initializing dma buffers. If irq has
been acquired and irq handler uses the dma buffer, kernel may crash
when interrupt comes in.
Fix the problem by postponing enabling irq after dma buffer
initialization. And warn once on null dma buffer pointer during the
initialization.
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Split regmap_config.use_single_rw into use_single_read and
use_single_write. This change enables drivers of devices which only
support bulk operations in one direction to use the regmap_bulk_*()
functions for both directions and have their bulk operation split into
single operations only when necessary.
Update all struct regmap_config instances where use_single_rw==true to
instead set both use_single_read and use_single_write. No attempt was
made to evaluate whether it is possible to set only one of
use_single_read or use_single_write.
Signed-off-by: David Frey <dpfrey@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
E.g. for snd_hdac_ext_link_clear_stream_id(), we should set (1 << stream)
as mask, and 0 as value, here correct it and several similar mismatches.
And, here also remove unreadable register_mask usage for those mask value
updating.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The BDL pointer used in snd_hdac_dsp_prepare() should be declared as
__le32, as warned by sparse:
sound/hda/hdac_stream.c:655:47: warning: incorrect type in argument 4 (different base types)
sound/hda/hdac_stream.c:655:47: expected restricted __le32 [usertype] **bdlp
sound/hda/hdac_stream.c:655:47: got unsigned int [usertype] **<noident>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM format type is defined with __bitwise, hence it can't be
passed as integer but needs an explicit cast. In this patch, instead
of the messy cast flood, define the format argument of
snd_hdac_calc_stream_format() to be the proper snd_pcm_format_t type.
This fixes sparse warnings like:
sound/hda/hdac_device.c:760:38: warning: incorrect type in argument 1 (different base types)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently HD-audio i915 audio binding doesn't support any delayed
binding, and supposes that the i915 driver registers the component
immediately. This has been OK, so far, but the work-in-progress
change in i915 may introduce the asynchronous binding, which
effectively delays the component registration.
For addressing it, implement a completion to be synced with the master
binding. The timeout is set to 10 seconds which should be long enough
and hopefully be not too annoying if anyone boots up a debugging
session with i915 KMS turned off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is the final step for more generic support of DRM audio
component. The generic audio component code is now moved to its own
file, and the symbols are renamed from snd_hac_i915_* to
snd_hdac_acomp_*, respectively. The generic code is enabled via the
new kconfig, CONFIG_SND_HDA_COMPONENT, while CONFIG_SND_HDA_I915 is
kept as the super-class.
Along with the split, three new callbacks are added to audio_ops:
pin2port is for providing the conversion between the pin number and
the widget id, and master_bind/master_unbin are called at binding /
unbinding the master component, respectively. All these are optional,
but used in i915 implementation and also other later implementations.
A note about the new snd_hdac_acomp_init() function: there is a slight
difference between this and the old snd_hdac_i915_init(). The latter
(still) synchronizes with the master component binding, i.e. it
assures that the relevant DRM component gets bound when it returns, or
gives a negative error. Meanwhile the new function doesn't
synchronize but just leaves as is. It's the responsibility by the
caller's side to synchronize, or the caller may accept the
asynchronous binding on the fly.
v1->v2: Fix missing NULL check in master_bind/unbind
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HD-audio i915 binding code contains a single pointer, hdac_acomp,
for allowing the access to audio component from the master bind/unbind
callbacks. This was needed because the callbacks pass only the device
pointer and we can't guarantee the object type assigned to the drvdata
(which is free for each controller driver implementation).
And this implementation will be a problem if we support multiple
components for different DRM drivers, not only i915.
As a solution, allocate the audio component object via devres and
associate it with the given device, so that the component callbacks
can refer to it via devres_find().
The removal of the object is still done half-manually via
devres_destroy() to make the code consistent (although it may work
without the explicit call).
Also, the snd_hda_i915_register_notifier() had the reference to
hdac_acomp as well. In this patch, the corresponding code is removed
by passing hdac_bus object to the function, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For allowing other drivers to use the DRM audio component, rename the
i915_audio_component_* with drm_audio_component_*, and split the
generic part into drm_audio_component.h. The i915 specific stuff
remains in struct i915_audio_component, which contains
drm_audio_component as the base.
The license of drm_audio_component.h is kept to MIT as same as the the
original i915_component.h.
This is a preliminary change for further development, and no
functional changes by this patch itself, merely code-split and
renames.
v1->v2: Use SPDX for drm_audio_component.h, fix remaining i915
argument in drm_audio_component.h
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add extended ops in the hdac_bus to allow calling the ASoC HDAC library
ops to reuse the legacy HDA codec drivers with ASoC framework.
Extended ops are used by the legacy codec drivers to call into
hdac_hda library, in the subsequent patches..
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove memory allocation within snd_hdac_ext_bus_device_init, to make
its behaviour identical to snd_hdac_bus_device_init. So that caller
can allocate the parent data structure containing hdac_device.
This API change helps in reusing the legacy HDA codec drivers with
ASoC platform drivers.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As per HDA spec section 4.3 - Codec Discovery, the software shall wait
for atleast 521usec for codec to respond after link reset.
With the multi-link capability each link is turned ON/OFF individually.
Link controller drives reset signal when it is turned ON.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch removes the hdac_ext_driver structure. The legacy and
enhanced HDaudio capabilities can be handled in a backward-compatible
way without separate definitions.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch removes the hdac_ext_bus structure. The legacy and
enhanced HDaudio capabilities can be handled in a backward-compatible
way without separate definitions.
Follow-up patches in this series handle the driver definition.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch removes the hdac_ext_device structure. The legacy and
enhanced HDaudio capabilities can be handled in a backward-compatible
way without separate definitions.
Follow-up patches in this series handle the bus and driver definitions.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce a new helper macro, snd_array_for_each(), to iterate for
each snd_array element. It slightly improves the readability than
lengthy open codes at each place.
Along with it, add const prefix to some obvious places.
There should be no functional changes by this.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current sync_power_state is local to hda code, moving it
core so that other users apart from hda legacy can use it.
The helper function ensures the actual state reaches the target state.
Signed-off-by: Abhijeet Kumar <abhijeet.kumar@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the commit 97cc2ed27e ("ALSA: hda - Fix yet another i915
pointer leftover in error path") cleared hdac_acomp pointer, the
WARN_ON() non-NULL check in snd_hdac_i915_register_notifier() may give
a false-positive warning, as the function gets called no matter
whether the component is registered or not. For fixing it, let's get
rid of the spurious WARN_ON().
Fixes: 97cc2ed27e ("ALSA: hda - Fix yet another i915 pointer leftover in error path")
Cc: <stable@vger.kernel.org>
Reported-by: Kouta Okamoto <kouta.okamoto@toshiba.co.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch renames all the variable instances of hdac_device with hdev
to prepare the code base to remove the usage of hdac_ext_device
data structures done in the following patches. Existing code uses hdev
and hdac as variable names for hdac_device as well as hdac_ext_device,
which creates confusion.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We got a regression report about the HD-audio HDMI chmap, where some
surround channels are reported as UNKNOWN. The git bisection pointed
the culprit at the commit 9b3dc8aa3f ("ALSA: hda - Register chmap
obj as priv data instead of codec"). The story behind scene is like
this:
- While moving the code out of the legacy HDA to the HDA common place,
the patch modifies the code to obtain the chmap array indirectly in
a byte array, and it expands it to kctl value array.
- At the latter operation, the size of the array is wrongly passed by
sizeof() to the pointer.
- It can be 4 on 32bit arch, thus too short for 6+ channels.
(And that's the reason why it didn't hit other persons; it's 8 on
64bit arch, thus it's usually enough.)
The code was further changed meanwhile, but the problem persisted.
Let's fix it by correctly evaluating the array size.
Fixes: 9b3dc8aa3f ("ALSA: hda - Register chmap obj as priv data instead of codec")
Reported-by: VDR User <user.vdr@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The biggest thing this release has been the conversion of the AC98 bus
to the driver model, that's been a long time coming so thanks to Robert
Jarzmik for his dedication there. Due to there being some AC97 MFD
there's a few fairly large changes in input and the MFD layer, mainly to
the wm97xx driver.
There's also some drivers/drm changes to support the new AMD Stoney
platform, these are shared with the DRM subsystem and should be being
merged via both.
Within the subsystem the overwhelming bulk of the changes is in the
Intel drivers which continue to need lots of cleanups and fixes, this
release they've also gained support for their open source firmware.
There's also some large changs in the core as Morimoto-san continues to
mirror operations into the component level in preparation for conversion
of drivers to that.
- The AC97 bus has finally caught up with the driver model thanks to
some dedicated and persistent work from Robert Jarzmik.
- Continued work from Morimoto-san on moving us towards being able to
use components for everything.
- Lots of cleanups for the Intel platform code, including support for
their open source audio firmware.
- Support for scaling MCLK with sample rate in simple-card.
- Support for AMD Stoney platform.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAloJhwMTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0KzbB/9tXryXYz3dnKVlm9rk+Cq0Xy4TrUNk
WY+Il+Di1b6CQJbAm9GSacJxR+siupZCjGC5roHznj/AA2l0RuxJXpxG40Db8ZX+
bDR7mIWtuTUJHazqXltafj9ydElRKVpOGPAi5YJhhW5bXQ3SR9fFy0D3mdcT02v4
SyMExhOMz+mdnuBhbWx9kqJ9LPzCs0ow+R4uoRgAQxpFXPBGtq06sMkK86lGfsl/
iRM36J6FIeIQQfSHG/dkkpoybVax43z4OH7G1IL2FOU7miwkjZh/TTh/xHTd86Mc
OOuGu4hB+MjvccSOa9HSrOqFjxtkZipstwqYVWoYQcUoIVpcg0YRk7TG
=5KBY
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.15
The biggest thing this release has been the conversion of the AC98 bus
to the driver model, that's been a long time coming so thanks to Robert
Jarzmik for his dedication there. Due to there being some AC97 MFD
there's a few fairly large changes in input and the MFD layer, mainly to
the wm97xx driver.
There's also some drivers/drm changes to support the new AMD Stoney
platform, these are shared with the DRM subsystem and should be being
merged via both.
Within the subsystem the overwhelming bulk of the changes is in the
Intel drivers which continue to need lots of cleanups and fixes, this
release they've also gained support for their open source firmware.
There's also some large changs in the core as Morimoto-san continues to
mirror operations into the component level in preparation for conversion
of drivers to that.
- The AC97 bus has finally caught up with the driver model thanks to
some dedicated and persistent work from Robert Jarzmik.
- Continued work from Morimoto-san on moving us towards being able to
use components for everything.
- Lots of cleanups for the Intel platform code, including support for
their open source audio firmware.
- Support for scaling MCLK with sample rate in simple-card.
- Support for AMD Stoney platform.
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On reading wrong capability pointer values driver may crash, so whenever
driver discovers unknown HDA capability, log it as error and stop traversing
the link list further.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The refresh of HD-audio widget sysfs kobjects via
snd_hdac_refresh_widget_sysfs() is slightly racy.
The driver recreates the whole tree from scratch after deleting the
whole. When CONFIG_DEBUG_KOBJECT_RELEASE option is used, kobject
release doesn't happen immediately but delayed, while the re-creation
of the same named kobject happens soon after invoking kobject_put().
This may end up with the conflicts of duplicated kobjects, as found in
the bug report below.
In this patch, we take another approach to refresh the tree: instead
of recreating the whole tree, just add the new nodes and delete the
non-existing nodes. Since the refresh happens only once at
initialization, no longer race would happen.
Along with the code change, merge snd_hdac_refresh_widget_sysfs() with
the existing snd_hdac_refresh_widgets() with an additional bool flag
for simplifying the code.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=197307
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The loop in snd_hdac_bus_parse_capabilities() may go to nirvana when
it hits an invalid register value read:
BUG: unable to handle kernel paging request at ffffad5dc41f3fff
IP: pci_azx_readl+0x5/0x10 [snd_hda_intel]
Call Trace:
snd_hdac_bus_parse_capabilities+0x3c/0x1f0 [snd_hda_core]
azx_probe_continue+0x7d5/0x940 [snd_hda_intel]
.....
This happened on a new Intel machine, and we need to check the value
and abort the loop accordingly.
[Note: the fixes tag below indicates only the commit where this patch
can be applied; the original problem was introduced even before that
commit]
Fixes: 6720b38420 ("ALSA: hda - move bus_parse_capabilities to core")
Cc: <stable@vger.kernel.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2610 304 8 2922 b6a sound/hda/hdac_i915.o
File size After adding 'const':
text data bss dec hex filename
2674 240 8 2922 b6a sound/hda/hdac_i915.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the codec device is unregistered / freed, it may release the
resource while being used in an unsolicited event like the jack
detection work. This leads to use-after-free.
The fix here is to unregister the device at first, i.e. removing the
codec from the list, then flushing the pending works to assure that
all unsol events are gone. After this point, we're free from
accessing the codec via unsol events, thus can release the resources
gracefully.
The issue was spotted originally by Intel CI, but it couldn't be
reproduced reliably by its nature. So let's hope this fix really
addresses the whole issues.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196045
Reported-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A quiet release for the core, but lots of new drivers this time around:
- A new, generalized, API for hooking up jacks which makes it easier to
write generic machine drivers for simple cases.
- Continuing fixes for issues with the x86 CPU drivers.
- New drivers for Cirrus CS35L35, DIO DIO2125, Everest ES7132,
HiSilicon hi6210, Maxim MAX98927, MT2701 systems with WM8960, Nuvoton
NAU8824, Odroid systems, ST STM32 SAI controllers and x86 systems with
DA7213
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlkH9Q4THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0D24B/4oQ67H01Tcq0ghrIsr/UNQnPi+ywx2
e5nkWNvWTM7gSUDOFjmD3ZM07Gf66IIyiFFSt6w93/lDQaOcGgsmBo9tnujR7ytQ
XXUiE1bvx7liZ09/2Rq7DyDXTpYcFAbxLdWt8uGs72misj0XrVToVFJhl5YcMRBE
qnbV1woxQwIvJ5m+GmbW2NZ8bRCnnsMQbBWCIWOtvSPhtZQlQ+m7waYTVn3/ieGR
cWIHwY4lSZycqaYDWZ+RPFipcAwzKTNt0MiXoCI02EX95275AbIHdWAgrVta04Al
muWP1XTkufO73NFqfvEF+Rrpi69pRCNhAS7TJY++d1moKCYgSpG8bAvD
=W3eF
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.12
A quiet release for the core, but lots of new drivers this time around:
- A new, generalized, API for hooking up jacks which makes it easier to
write generic machine drivers for simple cases.
- Continuing fixes for issues with the x86 CPU drivers.
- New drivers for Cirrus CS35L35, DIO DIO2125, Everest ES7132,
HiSilicon hi6210, Maxim MAX98927, MT2701 systems with WM8960, Nuvoton
NAU8824, Odroid systems, ST STM32 SAI controllers and x86 systems with
DA7213
This patch refines the definition of AZX_MLCTL_SPA and AZX_MLCTL_CPA
and add more definitions of ML registers
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The macros _snd_hdac_chip_read() and *_write() expand to different
types (b,w,l) per their argument. They were thought to be used only
internally for other snd_hdac_chip_*() macros, but in some situations
we need to call these directly, and they are way too ugly.
Instead of saving a few lines, we just write these macros explicitly
with the types, so that they can be used in a saner way.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
LLCH is a 16 bit register. Use readw instead of readl API.
Signed-off-by: B, Jayachandran <jayachandran.b@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check stream decoupled register value with requested value
before decoupling/coupling the stream.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
- first slice of the gvt device model (Zhenyu et al)
- compression support for gpu error states (Chris)
- sunset clause on gpu errors resulting in dmesg noise telling users
how to report them
- .rodata diet from Tvrtko
- switch over lots of macros to only take dev_priv (Tvrtko)
- underrun suppression for dp link training (Ville)
- lspcon (hmdi 2.0 on skl/bxt) support from Shashank Sharma, polish
from Jani
- gen9 wm fixes from Paulo&Lyude
- updated ddi programming for kbl (Rodrigo)
- respect alternate aux/ddc pins (from vbt) for all ddi ports (Ville)
* tag 'drm-intel-next-2016-10-24' of git://anongit.freedesktop.org/drm-intel: (227 commits)
drm/i915: Update DRIVER_DATE to 20161024
drm/i915: Stop setting SNB min-freq-table 0 on powersave setup
drm/i915/dp: add lane_count check in intel_dp_check_link_status
drm/i915: Fix whitespace issues
drm/i915: Clean up DDI DDC/AUX CH sanitation
drm/i915: Respect alternate_ddc_pin for all DDI ports
drm/i915: Respect alternate_aux_channel for all DDI ports
drm/i915/gen9: Remove WaEnableYV12BugFixInHalfSliceChicken7
drm/i915: KBL - Recommended buffer translation programming for DisplayPort
drm/i915: Move down skl/kbl ddi iboost and n_edp_entires fixup
drm/i915: Add a sunset clause to GPU hang logging
drm/i915: Stop reporting error details in dmesg as well as the error-state
drm/i915/gvt: do not ignore return value of create_scratch_page
drm/i915/gvt: fix spare warnings on odd constant _Bool cast
drm/i915/gvt: mark symbols static where possible
drm/i915/gvt: fix sparse warnings on different address spaces
drm/i915/gvt: properly access enabled intel_engine_cs
drm/i915/gvt: Remove defunct vmap_batch()
drm/i915/gvt: Use common mapping routines for shadow_bb object
drm/i915/gvt: Use common mapping routines for indirect_ctx object
...
DP MST provides the capability to send multiple video and audio streams
through a single port. This requires the API's between i915 and audio
drivers to distinguish between multiple audio capable displays that can be
connected to a port. Currently only the port identity is shared in the
APIs. This patch adds support for MST with an additional parameter
'int pipe'. The existing parameter 'port' does not change it's meaning.
pipe =
MST : display pipe that the stream originates from
Non-MST : -1
Affected APIs:
struct i915_audio_component_ops
- int (*sync_audio_rate)(struct device *, int port, int rate);
+ int (*sync_audio_rate)(struct device *, int port, int pipe,
+ int rate);
- int (*get_eld)(struct device *, int port, bool *enabled,
- unsigned char *buf, int max_bytes);
+ int (*get_eld)(struct device *, int port, int pipe,
+ bool *enabled, unsigned char *buf, int max_bytes);
struct i915_audio_component_audio_ops
- void (*pin_eld_notify)(void *audio_ptr, int port);
+ void (*pin_eld_notify)(void *audio_ptr, int port, int pipe);
This patch makes dummy changes in the audio drivers (thanks Libin) for
build to succeed. The audio side drivers will send the right 'pipe' values
for MST in patches that will follow.
v2:
Renamed the new API parameter from 'dev_id' to 'pipe'. (Jim, Ville)
Included Asoc driver API compatibility changes from Jeeja.
Added WARN_ON() for invalid pipe in get_saved_encoder(). (Takashi)
Added comment for av_enc_map[] definition. (Takashi)
v3:
Fixed logic error introduced while renaming 'dev_id' as 'pipe' (Ville)
Renamed get_saved_encoder() to get_saved_enc() to reduce line length
v4:
Rebased.
Parameter check for pipe < -1 values in get_saved_enc() (Ville)
Switched to for_each_pipe() in get_saved_enc() (Ville)
Renamed 'pipe' to 'dev_id' in audio side code (Takashi)
v5:
Included a comment for the dev_id arg. (Libin)
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474488168-2343-1-git-send-email-dhinakaran.pandiyan@intel.com
Trival fix, some dev_err messages are missing a \n, so add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the unused one as we have moved it up to hdac core.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that we have the bus parse capabilities moved to core, we need to
convert users.
The SKL driver and HDA extended lib needs to converted in single patch,
otherwise we regress on the functionality.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA capability introduced recently are move to hdac core so that it can
be used by legacy driver as well. Also move the capability pointers up
to hdac_bus object.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
krealloc() doesn't work always properly with __GFP_ZERO flag as
expected. For clearing the reallocated area, we need to clear
explicitly instead.
Reported-by: Joe Perches <joe@perches.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Call path:
1) snd_hdac_power_up_pm()
2) snd_hdac_power_up()
3) pm_runtime_get_sync()
4) __pm_runtime_resume()
5) rpm_resume()
The rpm_resume() returns 1 when the device is already active.
Because the return value is unmodified, the hdac regmap read/write
functions should allow this value for the retry I/O operation, too.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes some warnings from klockwork.
These warnings are not the real issues. The patch
adds the sanity check.
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The updates this time around are almost all driver code:
- Further slow progress on the topology code.
- Substantial updates and improvements for the da7219, es8328, fsl-ssi
Intel and rcar drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXOao7AAoJECTWi3JdVIfQ3EQH/1Z4nukvcOeZgVN/4K9b27t2
LYSyPH4+7XiDsi24UAyxZWls625t+1XRtolS0yHYY+IMObkeH/T+StTirDG4C1Mv
0uw/lEs5XmkSPFMad2fDcVXhf+D6EsvuLZ24qLKhoi8TyePv6GRvYapitE4dAI7Z
bBwjT+f9r1qSMJvfCmqit8zDneDFMKd7oqPmBW6NpFri5/ksn1KUnd/zOGu2SlSd
R01Oa2VbRDGj8/Zzu5MORvgLLucxTqtAFYeF3T52M5oc33IBWvbha4fk/BDOswbz
H9S3vHyakmbZgXnnGMTp4qz0bxA76YaHzjtqgGUEMbigHTsB0PP5TtII3i5LkaY=
=Zsr1
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.7
The updates this time around are almost all driver code:
- Further slow progress on the topology code.
- Substantial updates and improvements for the da7219, es8328, fsl-ssi
Intel and rcar drivers.
The HDA links can be switched off when not is use, similarly
command DMA can be stopped as well. This calls for a reference
counting mechanism on the link by it's users to manage the link
power. The DMA can be turned off when all links are off
For this we add two APIs
snd_hdac_ext_bus_link_get
snd_hdac_ext_bus_link_put
They help users to turn up/down link and manage the DMA as well
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the DMAs are not being quiesced properly, it may lead to
stability issues, so the recommendation is to wait till DMAs are
stopped.
After setting the stop bit of RIRB/CORB DMA, we should wait for
stop bit to be set.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ebus is a member of extended device and was never initialized, so
do this at device creation.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This helper is copied from legacy hda driver.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a fairly large collection of fixes but almost all driver
specific ones, especially to the new Intel drivers which have had a lot
of recent development. The one core fix is a change to the debugfs code
to avoid crashes in some relatively unusual configurations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXINZtAAoJECTWi3JdVIfQ+BwH/1eLqMfCSZM9nsDr1QMvOCDP
SO4ZoWqvYplBcS8pYKbJmqtuo8jMxT3VIQF+b5hPAVhgpLwMmy9qeFtatqCQ2WDC
GfCqW8LSKtrzwUwmoRrtHx7vfBLP1/z78F8ORQzwhrplTCBhvPLbUOrV51EFj6tf
Dfo2tW0uxww9iCZduYu4LadOhFOfuw+5shUrJk5A5f975Zbdgyke4CbRnlbDPXLq
d4i7bNfiISkSJiKMpdZFeiOQCd0+uXHh2WkMtVYSGVTA2Kf7d7HtX+JpEFFmaJgJ
8CndjgNJ1ZXtMHl1pMYmNqKJ5mEgmVtbGGJWY4QmQBva0EfQ+vLZt78BG3qvJwk=
=SXH2
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.6
This is a fairly large collection of fixes but almost all driver
specific ones, especially to the new Intel drivers which have had a lot
of recent development. The one core fix is a change to the debugfs code
to avoid crashes in some relatively unusual configurations.
The recent bug report suggests that BCLK setup for i915 HSW/BDW needs
to be updated at each HDMI hotplug, not only at initialization and
resume. That is, we need to update HSW_EM4 and HSW_EM5 registers at
ELD notification, too. Otherwise the HDMI audio may be out of sync
and played in a wrong pitch.
However, the HDA codec driver has no access to the controller
registers, and currently the code managing these registers is in
hda_intel.c, i.e. local to the controller driver. For allowing the
explicit BCLK update from the codec driver, as in this patch, the
former haswell_set_bclk() in hda_intel.c is moved to hdac_i915.c and
exposed as snd_hdac_i915_set_bclk(). This is called from both the HDA
controller driver and intel_pin_eld_notify() in HDMI codec driver.
Along with this change, snd_hdac_get_display_clk() gets dropped as
it's no longer used.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91410
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HD-audio driver uses regmap cache bypass feature for reading a raw
value without the cache. But this is racy since both the cached and
the uncached reads may occur concurrently. The former is done via the
normal control API access while the latter comes from the proc file
read.
Even though the regmap itself has the protection against the
concurrent accesses, the flag set/reset is done without the
protection, so it may lead to inconsistent state of bypass flag that
doesn't match with the current read and occasionally result in a
kernel WARNING like:
WARNING: CPU: 3 PID: 2731 at drivers/base/regmap/regcache.c:499 regcache_cache_only+0x78/0x93
One way to work around such a problem is to wrap with a mutex. But in
this case, the solution is simpler: for the uncached read, we just
skip the regmap and directly calls its accessor. The verb execution
there is protected by itself, so basically it's safe to call
individually.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=116171
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The existing TLV callback implementation copies all of the
cea_channel_speaker_allocation map table to the TLV container
irrespective of what is reported by sink. This is of little use
to the userspace application.
With this patch, it parses the spk_alloc block as queried from
the ELD, and copies only the corresponding mapping channel
allocation entries from the cea channel speaker allocation table.
Thus the user can parse the TLV container to identify sink's
capability and set the channel map accordingly.
It shouldn't impact the behavior in AMD chipset, as this makes
use of already parsed spk alloc block to calculate the channel
map.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On Skylake and onwards, the HD-audio controller driver needs to bind
with i915 for having the control of power well audio domain before
actually probing the codec. This leads to the load of i915 driver
from the audio driver side. But, there are systems that have no Intel
graphics but Nvidia or AMD GPU, although they still use HD-audio bus
for the onboard audio codecs. On these, loading the i915 driver is
nothing but a useless memory and CPU consumption.
A simple way to avoid it is just to look for the Intel graphics PCI
entry beforehand, and try to bind with i915 only when such an entry is
found. Currently, it assumes the PCI display class. If another class
appears, this needs to be extended (although it's very unlikely).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hdac_acomp object in hdac_i915.c is left as assigned even after
binding with i915 actually fails, and this leads to the WARN_ON() at
the next load of the module.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94736
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [d745f5e7b8b2: ALSA: hda - Add the pin / port mapping on
Intel ILK and VLV] introduced a WARN_ON() to check the pointer for
avoiding the double initializations. But hdac_acomp pointer wasn't
cleared at snd_hdac_i915_exit(), thus after reloading the HD-audio
driver, it may result in the false positive warning. This patch makes
sure to clear the leftover pointer at exit.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94736
Reported-by: Daniela Doras-prodan <daniela.doras-prodan@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Intel IronLake and ValleyView platforms have different HDMI widget pin
and digital port mapping from other newer ones. The recent ones
(HSW+) have NID 0x05 to 0x07 for port B to port D, while these chips
have NID 0x04 to 0x06.
For adapting this mapping, pass the codec object instead of the bus
object to snd_hdac_sync_audio_rate() and snd_hdac_acomp_get_eld() so
that they can check the codec ID and calculate the mapping properly.
The changes in the HDMI codec driver side will follow in the later
patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It is always better to use list_for_each_entry_safe() while doing
cleanup. So use this instead of open coding this in list in
snd_hdac_stream_free_all()
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is an implicit rule to map between pin NID and port number on
Intel HDMI/DP codec: the mapping is fixed only for NID 0x05, 0x06 and
0x07. For avoiding the possible memory corruption, add a sanity check
for the NID value and splat WARN_ON() for invalid accesses.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HD-audio driver has a mechanism to trigger the runtime resume
automatically at accessing the verbs. This auto-resume, however,
causes the mutex deadlock when invoked from the regmap handler since
the regmap keeps the mutex while auto-resuming. For avoiding that,
there is some tricky check in the HDA regmap handler to return -EAGAIN
error to back-off when the codec is powered down. Then the caller of
regmap r/w will retry after properly turning on the codec power.
This works in most cases, but there seems a slight race between the
codec power check and the actual on-demand auto-resume trigger. This
resulted in the lockdep splat, eventually leading to a real deadlock.
This patch tries to address the race window by getting the runtime PM
refcount at the check time using pm_runtime_get_if_in_use(). With
this call, we can keep the power on only when the codec has been
already turned on, and back off if not.
For keeping the code consistency, the code touching the runtime PM is
stored in hdac_device.c although it's used only locally in
hdac_regmap.c.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add slot and channel count programming to hdmi_chmap object and
move the chmap_ops to core. Use register_chmap_ops API to
register for default ops. Override specific chmap ops in the
driver.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the interrupt handler of HD-audio driver assumes that no irq
update is needed while processing the irq. But in reality, it has
been confirmed that the HW irq is issued even during the irq
handling. Since we clear the irq status at the beginning, process the
interrupt, then exits from the handler, the lately issued interrupt is
left untouched without being properly processed.
This patch changes the interrupt handler code to loop over the
check-and-process. The handler tries repeatedly as long as the IRQ
status are turned on, and either stream or CORB/RIRB is handled.
For checking the stream handling, snd_hdac_bus_handle_stream_irq()
returns a value indicating the stream indices bits. Other than that,
the change is only in the irq handler itself.
Reported-by: Libin Yang <libin.yang@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently HD-audio driver on Intel Skylake or Broxteon gives an error
message when binding with i915 audio component fails. However, this
isn't any serious error on a system without Intel graphics. Indeed
there are such systems, where a third-party codec (e.g. Creative) is
put on the mobo while using other discrete GPU (e.g. Nvidia).
Printing a kernel "error" message is overreaction in such a case.
This patch downgrades the print level for that message. For systems
that mandate the i915 binding (e.g. Haswell or Broadwell HDMI/DP),
another kernel error message is shown in addition to make clear what
went wrong.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111021
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A bunch more updates for v4.5, mainly driver work:
- More topology API enhancements from Mengdong Lin working towards
making everything more component based and being able to specify PCM
links via topology.
- Large sets driver updates from Cirrus, Intel (mainly more Skylake
support) and Renesas.
- New drivers for AMD ACP, Atmel PDMIC, Dialog DA7218, Imagination
Technologies SoC IPs, Rockchip RK3036 Inno CODEC and Texas Instruments
PCM3168A.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWk8EUAAoJECTWi3JdVIfQ+RwH/jid388X6x6YOa84Rs7InrIS
m2rVdjDAMAbK+smhalHzvLOGnHjpygegwZ/9/1DUiSPbcXdqMkzLoaweeVUXhu27
9G3zT0Xz1XVn/+5029oIlrsyPCtM5O9PlPOO7tiQSTBADjvl+I4hl6FHZ1LGT7Sr
tiOTAiOmIisELBzBF0L7fB18iBgE3VqkhG8obrMiTXVWgfZuRJL7kdH2WuHYFXpM
JxBcy9VrCp0JHxg+qCD7xYyFdKLE6eP96gpLi94JBqW8I3wrwmEmUqNKs+r8I7Vj
bh5/v6A2V0EaJWCKzWBARHE7BR3E2uJeoD0PcY59Kn7BKhKPjTe99g2ngTk1hIU=
=BvEm
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.4-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Last updates for v4.5
A bunch more updates for v4.5, mainly driver work:
- More topology API enhancements from Mengdong Lin working towards
making everything more component based and being able to specify PCM
links via topology.
- Large sets driver updates from Cirrus, Intel (mainly more Skylake
support) and Renesas.
- New driver for AMD ACP
- Rename PCM1792a driver to be generic pcm179x
We have an API for powering down all links, we need a similar one
for powering up links, so add for power up as well
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
HW recommends 180us for worst case values for link power up
delay, so change the current delay value from 50 (150us) to 150
(450us)
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
A stream is by default in coupled mode, in DSP operation we move
it to decoupled mode. On cleanup HW expects that we leave it back
to default state so couple the DMA on cleanup.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Skylake sports new capability of DMA resume, DRSM where we can
resume the DMA. This capability is defined by presence of
AZX_DRSM_CAP_ID.
If this capability is present, we use this capability.
So we add:
snd_hdac_ext_stream_drsm_enable() - DMA resume caps
snd_hdac_ext_stream_set_dpibr() - set the DMA position
snd_hdac_ext_stream_set_lpib() - set the lpib
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
A couple of i915_audio_component ops have been added and accessed
directly from patch_hdmi.c. Ideally all these should be factored out
into hdac_i915.c.
This patch does it, adds two new helper functions for setting N/CTS
and fetching ELD bytes. One bonus is that the hackish widget vs port
mapping is also moved to hdac_i915.c, so that it can be fixed /
enhanced more cleanly.
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Give some readable comment in kernel doc style for each exported
function, as I promised in the previous meetings. While we're at it,
fix the wrong comments, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
By setting the MODALIAS variable in uevents, userspace helpers will be
enabled to load modules via the module alias associated with a device.
This information is required to automatically load HDA codec drivers
instead of having to explicitly request the various modules in the HDA
core code.
[Note that currently the legacy HDA controller driver tries to bind
codec modules manually. It's for supporting the fallback generic
drivers. This new udev modalias support was added rather for ASoC
HDA ext drivers, since this addition itself won't hurt the legacy HDA
-- tiwai]
[Use the common helper function to generate the modalias -- tiwai]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch just adds modalias sysfs entry to each hdaudio bus entry.
[rewritten to call the common helper function by tiwai]
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch provide a new common helper function,
snd_hdac_codec_modalias(), to give the codec modalias name string.
This function will be used by multiple places in the later patches.
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For generating modalias entries automatically, move the definition of
struct hda_device_id to linux/mod_devicetable.h and add the handling
of this record in file2alias helper. The new modalias is represented
with combination of vendor id, device id, and api version as
"hdaudio:vNrNaN".
This patch itself doesn't convert the existing modaliases. Since they
were added manually, this patch won't give any regression by itself at
this point.
[Modified the modalias format to adapt the api_version field, and drop
invalid ANY_ID definition by tiwai]
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few multiple codec drivers do renaming the chip_name string but all
these are open-coded and some of them have even no error check. Let's
make common helpers to do it properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Compiling the hdac extended core on arm fails with below error:
sound/hda/ext/hdac_ext_bus.c: In function 'hdac_ext_writel':
>> sound/hda/ext/hdac_ext_bus.c:29:2: error: implicit declaration of
>> function
+'writel' [-Werror=implicit-function-declaration]
writel(value, addr);
^
sound/hda/ext/hdac_ext_bus.c: In function 'hdac_ext_readl':
>> sound/hda/ext/hdac_ext_bus.c:34:2: error: implicit declaration of
>> function
+'readl' [-Werror=implicit-function-declaration]
return readl(addr);
This is fixed by explicitly including io.h
Fixes: 99463b3a39 - ('ALSA: hda: provide default bus io ops extended hdac')
Reported-by: kbuild test robot <lkp@intel.com>
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current codec helpers are local to hda code and needs to be moved to
core so that other users can use it.
The helpers to read/write the codec and to check the
power state of widgets is copied
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
if the stream is decoupled and both link and host are used, while
releasing the stream, need to check if link and host stream are
not in use. This patch adds fix to check if the host/link stream
is in used before coupling it back when releasing the stream.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Bits in LOSIDV need to be set to map the stream id for specific link.
Fixing this by setting the required bits in the register.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This lets the interested codec be notified when an i915 pin/ELD
event happens.
[tiwai: Fixed a trivial build error for CONFIG_SND_HDA_I915=n]
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When snd_hdac_refresh_widget_sysfs() is called before the first
hda_widget_sysfs_init(), the next call overrides and eventually
fails. This results in unexpected Oops, something like:
BUG: unable to handle kernel NULL pointer dereference at 00000000000000c8
IP: [<ffffffff8180e2a3>] hdmi_chmap_ctl_info+0x23/0x40
The fix is to add a check of the existing sysfs tree. Also, for more
safety, this patch adds the checks of device_is_registered() in
snd-hdac_refresh_wdiget_sysfs(), too.
Fixes: fa4f18b4f4 ('ALSA: hda - Refresh widgets sysfs at probing Haswell+ HDMI codecs')
Bugizlla: https://bugzilla.kernel.org/show_bug.cgi?id=103431
Reported-by: Andreas Reis <andreas.reis@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a helper to find the stream using stream tag and direction.
This is useful for drivers to query stream based on stream tag
and direction, fox example while downloading FW thru DSP loader
code
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
spbmaxfifo API is actually a query function not a set function so
name it snd_hdac_ext_stream_get_spbmaxfifo()
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While creating hdac_ext_device, we used hdev for sizeof insteadof
edev, which resulted in eventual crash of the system Fix the size
here
Fixes: a512f56116 ('ALSA: hdac: add hdac extended device')
Reported-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdac_ext_stream assign doesn't require key mapping as in case of
hdac_stream. So for host stream, the key to device mapping needs
to be removed.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The drivers need to set the spib and maxfifios values, so add
these new APIs snd_hdac_ext_stream_set_spib() and
snd_hdac_ext_stream_set_spbmaxfifo() APIs
For these APIs we also need to have spib and fifos pointer, so
add these to hdac_ext_stream and initialize them at stream init
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
New HDA controllers like Skylake sport multiple HDA links, so we need a
helper to turn off all the links in one go while suspending the device so
add snd_hdac_ext_bus_link_power_down_all() API
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SPCAP and Mutilink register offset were incorrect as offset needs
to be based on capability offset. So correct the offset for
read/write of spcap/link register.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some codecs like Intel HDMI by default do not show up all the pins, they
have to be manually enabled, so we need to refresh the codec widgets and
then recreate the sysfs tree. So add new API snd_hdac_refresh_widget_sysfs()
to do this. It should be be used by codec driver after sending magic verbs
to codec
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds new extended driver objects and API for registering the
extended devices.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds based hdac extended device object which will be used by
ASoC HDAC codecs
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HDAC extended device objects are created by HDAC extended bus on probe.
When controller is removed they should be removed as well, so add API
snd_hdac_ext_bus_device_remove for this
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd_hdac_chip_readl return can never be less than zeros,
so no point in checking for the return value
This fixes following static checker warnings in
snd_hdac_ext_bus_parse_capabilities
sound/hda/ext/hdac_ext_controller.c:47
snd_hdac_ext_bus_parse_capabilities()
warn: unsigned 'offset' is never less than zero.
sound/hda/ext/hdac_ext_controller.c:54
snd_hdac_ext_bus_parse_capabilities()
warn: unsigned 'cur_cap' is never less than zero.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This fixes issue in assigning host stream in case of
decoupled mode. The check to verify if the stream is already
in use was wrong so fix that
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the controller is powered up but the HDMI codec is powered down
on Skylake, the power well is turned off. When the codec is then
powered up again, we need to poke the codec a little extra to make
sure it wakes up. Otherwise we'll get sad "no response from codec"
messages and broken audio.
This also changes azx_runtime_resume to actually call
snd_hdac_set_codec_wakeup for Skylake (before STATETS read).
(Otherwise it would only have been called for Haswell and Broadwell,
which both do not need it, so this probably was not the author's
intention.)
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes the return type of snd_hdac_power_up/down() and
variants to pass the error code from the underlying
pm_runtime_get/put() calls. Currently they are ignored, but in most
places, these should be handled properly.
As an example, the regmap handler is updated to check the return value
and accesses the register only when the wakeup succeeds.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The kobject_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A typical io ops use simple io accessors which can be common for most
drivers, so provide a default ops which will be used if driver doesn't
provide one
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In HDA extended bus the HDA link objects are created when multilink
capabilities are parsed. We need a routine which free up these link objects
for a bus. So add snd_hdac_link_free_all routine
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDAC extended core should create streams for an extended bus and also free
up those on cleanup. So introduce snd_hdac_ext_stream_init_all and
snd_hdac_stream_free_all routines
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since this is common option for HDA driver to specfiy pre-allocated
buffer, we should make this option availble to all HDA driver by
moving this to HDA core
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now we have the bus and controller code added to find and initialize
the extended capabilities. Now we need to use them in stream code to
decouple stream, manage links etc
So this patch adds the stream handling code for extended capabilities
introduced in preceding patches
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The controller needs to support the new capabilities and allow
reading, parsing and initializing of these capabilities, so this patch
does it
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new HDA controllers from Intel support new capabilities like
multilink, pipe processing, SPIB, GTS etc In order to use them we
create an extended HDA bus which embed the hdac bus and contains the
fields for extended configurations
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Yet another regression by the transition to regmap cache; for better
usability, we had the fake mute control using the zero amp value for
Conexant codecs, and this was forgotten in the new hda core code.
Since the bits 4-7 are unused for the amp registers (as we follow the
syntax of AMP_GET verb), the bit 4 is now used to indicate the fake
mute. For setting this flag, snd_hda_codec_amp_update() becomes a
function from a simple macro. The bonus is that it gained a proper
function description.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This merges and resolves the non-trivial conflicts with the recent fix
for hda-i915 binding fallback.
Conflicts:
sound/pci/hda/hda_intel.c
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the missing NULL checks so that snd_hdac_i915*() can be called
even after the binding with i915 failed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Along with the transition to regmap for managing the cached parameter
reads, the caps overwrite was also moved to regmap cache. The cache
change itself works, but it still tries to write the non-existing verb
(the HDA parameter is read-only) wrongly. It's harmless in most
cases, but some chips are picky and may result in the codec
communication stall.
This patch avoids it just by adding the missing flag check in
reg_write ops.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA codec drivers can be matched using vendor id and revision id typically.
So provide a match function which does this and is loaded when driver hasn't
provided one (default behaviour)
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The file is moved to hda core and renamed to hdac_i915.c, so can be used
by both legacy HDA driver and new Skylake audio driver.
- Add snd_hdac_ prefix to the public APIs.
- The i915 audio component is moved to core bus and dynamically allocated.
- A static pointer hdac_acomp is used to help bind/unbind callbacks to get
this component, because the sound card's private_data is used by the azx
chip pointer, which is a legacy structure. It could be removed if private
_data changes to some core structure which can be extended to find the
bus.
- snd_hdac_get_display_clk() is added to get the display core clock for
HSW/BDW.
- haswell_set_bclk() is moved to hda_intel.c because it needs to write the
controller registers EM4/EM5, and only legacy HD-A needs it for HSW/BDW.
- Move definition of HSW/BDW-specific registers EM4/EM5 to hda_register.h
and rename them to HSW_EM4/HSW_EM5, because other HD-A controllers have
different layout for the extended mode registers.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The CA0132 DSP loader leads to NULL deference since the recent
transition to HDA core code, as it unconditionally accesses
hdac_stream->substream->runtime. For DSP loading, the substream
shouldn't be assigned.
This patch addresses the NULL dereference above in addition to assure
the substream is cleared while DSP loading.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98151
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the trace of snd_hdac_stream_start and snd_hdac_stream_stop.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A flag "link_power_control" is added to indicate whether a codec needs to
control the link power. And a new bus ops link_power() is defined for the
codec to request to enable/disable the link power.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This will be used by hda controller driver to
setup stream params in prepare. This function will
setup the bdl and periods.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For fixing randconfig build errors like:
sound/hda/hdac_stream.c: In function 'azx_timecounter_init':
sound/hda/hdac_stream.c:365:2: error: implicit declaration of function 'CLOCKSOURCE_MASK' [-Werror=implicit-function-declaration]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Daniel Vetter