Make these const as they are only used in a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make these const as they are only stored in the algo field of
i2c_adapter structure, which is const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds the I2C controller driver for Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The structure cht_wc_i2c_adap_driver is local to the source
and does not need to be in global scope, so make it static.
Cleans up sparse warning:
symbol 'cht_wc_i2c_adap_driver' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In addition to the base, low and high clock configuration, the AC timing
register #1 on the AST2400 houses fields controlling:
1. tBUF: Minimum delay between Stop and Start conditions
2. tHDSTA: Hold time for the Start condition
3. tACST: Setup time for Start and Stop conditions, and hold time for the
Repeated Start condition
These values are defined in hardware on the AST2500 and therefore don't
need to be set.
aspeed_i2c_init_clk() was performing a direct write of the generated
clock values rather than a read/mask/modify/update sequence to retain
tBUF, tHDSTA and tACST, and therefore cleared the tBUF, tHDSTA and tACST
fields on the AST2400. This resulted in a delay/setup/hold time of 1
base clock, which in some configurations is not enough for some devices
(e.g. the MAX31785 fan controller, with an APB of 48MHz and a desired
bus speed of 100kHz).
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Sun, Yunying reported the following failure on Denverton micro-server:
EDAC DEBUG: pnd2_init:
EDAC DEBUG: pnd2_probe:
EDAC DEBUG: dnv_rd_reg: Read b_cr_tolud_pci=00000000_80000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_touud_lo_pci=00000000_80000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_touud_hi_pci=00000000_00000004
EDAC DEBUG: dnv_rd_reg: Read b_cr_asym_mem_region0_mchbar=00000000_00000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_asym_mem_region1_mchbar=00000000_00000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_mot_out_base_mchbar=00000000_00000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_mot_out_mask_mchbar=00000000_00000000
EDAC pnd2: Failed to register device with error -19.
On Denverton micro-server, the presence of the P2SB bridge PCI device is
enabled or disabled by the item 'RelaxSecConf' in BIOS setup menu. When
'RelaxSecConf' is enabled, the P2SB PCI device is present and the pnd2_edac
EDAC driver also uses it to get BAR. Hiding the P2SB PCI device caused the
pnd2_edac EDAC driver failed to get BAR then reported the above failure.
Therefor, store the presence state of P2SB PCI device before unhiding it
for reading BAR and restore the presence state after reading BAR.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Reported-by: Yunying Sun <yunying.sun@intel.com>
Tested-by: Yunying Sun <yunying.sun@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There seems to be no need for separate ones since all users include both
files anyhow. Merge them because include/linux/i2c is to be deprecated.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c driver can run into driver dependency issues if its loaded
before a clock driver it depends on. Therefore, EPROBE_DEFER may be
returned by devm_clk_get and should be returned in probe to allow the
kernel to reprobe the driver at a later time. This patch allows the error
value returned by devm_clk_get to be passed through and not overwritten.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add i2c compatible for MT7622. Compare to MT8173 i2c controller,
MT7622 limits message numbers to 255, and does not support 4GB
DMA mode.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Cherry Trail Whiskey Cove PMIC's IRQ line is attached to one of
the GPIOs of the Cherry Trail SoC. The CHT GPIO controller sometimes
fails to deliver IRQs (seen when there is an IRQ storm on another pin).
This commit works around this by reducing the long timeout which was
a poor attempt to workaround this from 3s to 30ms and after that
manually checking the status register for transfer completion by
calling the threaded IRQ handler directly.
This is safe todo as the entire threaded IRQ handler is protected
by a mutex.
Note 30ms should be more then long enough, at 100KHz any smbus single
byte transaction should be finished in 4ms.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Testing has shown that writing 1 to clear the read-complete irq does
not work until the data register has been read first.
This commit fixes the driver to read the data register first, halving the
amount of interrupts in most cases since we mostly read on this i2c bus.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Although unlikely without locking the smbux_xfer function may miss
the nack flag and further fixes in this patch-set add some more
complex constructions which need protection.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
24xx BMCs have larger clock divider granularity which can cause problems
when trying to set them as 25xx clock dividers; this adds clock setting
code specific to 24xx.
This also fixes a potential issue where clock dividers were rounded down
instead of up.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-i2c@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Intel Cherry Trail Whiskey Cove PMIC does not contain a builtin
battery charger, instead boards with this PMIC use an external TI
bq24292i charger IC, which is connected to a SMBUS controller built into
the PMIC.
This commit adds an i2c-bus driver for the PMIC's builtin SMBUS
controller. The probe function for this i2c-bus will also register an
i2c-client for the TI bq24292i charger after the i2c-bus has been
registered.
Note that several device-properties are set on the client-device to
tell the bq24190 power-supply driver to integrate the Whiskey Cove PMIC
and e.g. use the PMIC's BC1.2 detection (through extcon) to determine
the maximum input current.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Support for the i2c controller on rv1108 soc.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When resuming, set up registers that have been lost in the sleep state.
Also, add clock handling in the resume / suspend hooks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When resuming, set up registers that have been lost in the sleep state.
Also, add clock handling in the resume / suspend hooks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Check for i2c_algorithm and i2c_adapter_quirks structures that are only
stored in the algo and quirks fields of an i2c_adapter structure
correspondingly. These fields are declared const, so i2c_algorithm and
i2c_adapter_quirks structures that have this property can be declared
as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> (for designware)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Several drivers call to_platform_device() to get platform_device
and pass it to platform_get_drvdata(). In platform_get_drvdata(),
the platform_device is converted back to struct device again.
Use dev_get_drvdata() to avoid platform_device/device dance.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> (for DesignWare only)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The speed of sending i2c master code in high-speed mode depends on
source clock, clock-div and TIMING register. The source clock and
clock-div of different SoC are not all the same. In order to send
i2c master code at 400k in high-speed mode, a appropriate value
should be set to TIMING register for a certain source clock and
clock-div.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"This pull request contains:
- i2c core reorganization. One source file became too monolithic. It
is now split up, yet we still have the same named object as the
final output. This should ease maintenance.
- new drivers: ZTE ZX2967 family, ASPEED 24XX/25XX
- designware driver gained slave mode support
- xgene-slimpro driver gained ACPI support
- bigger overhaul for pca-platform driver
- the algo-bit module now supports messages with enforced STOP
- slightly bigger than usual set of driver updates and improvements
and with much appreciated quality assurance from Andy Shevchenko"
* 'i2c/for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (51 commits)
i2c: Provide a stub for i2c_detect_slave_mode()
i2c: designware: Let slave adapter support be optional
i2c: designware: Make HW init functions static
i2c: designware: fix spelling mistakes
i2c: pca-platform: propagate error from i2c_pca_add_numbered_bus
i2c: pca-platform: correctly set algo_data.reset_chip
i2c: acpi: Do not create i2c-clients for LNXVIDEO ACPI devices
i2c: designware: enable SLAVE in platform module
i2c: designware: add SLAVE mode functions
i2c: zx2967: drop COMPILE_TEST dependency
i2c: zx2967: always use the same device when printing errors
i2c: pca-platform: use dev_warn/dev_info instead of printk
i2c: pca-platform: use device managed allocations
i2c: pca-platform: add devicetree awareness
i2c: pca-platform: switch to struct gpio_desc
dt-bindings: add bindings for i2c-pca-platform
i2c: cadance: fix ctrl/addr reg write order
i2c: zx2967: add i2c controller driver for ZTE's zx2967 family
dt: bindings: add documentation for zx2967 family i2c controller
i2c: algo-bit: add support for I2C_M_STOP
...
Only certain system configurations may use the I2C slave mode so let the
support be optional. This allow reducing module size if needed:
text data bss dec hex filename
10328 1336 16 11680 2da0 drivers/i2c/busses/i2c-designware-core.ko
7222 1136 8 8366 20ae drivers/i2c/busses/i2c-designware-core.ko
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Luis Oliveira <lolivei@synopsys.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Recent i2c-designware slave support patches use master or slave HW init
functions through the function pointer so we can declare them static.
While at it, rename i2c_dw_init() as i2c_dw_init_master().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Luis Oliveira <lolivei@synopsys.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Trivial fixes to spelling mistakes in dev_dbg message
"STAUTS" -> "STATUS"
"SLAVE_ACTTVITY" -> "SLAVE_ACTIVITY"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rather than returning -ENODEV if i2c_pca_add_numbered_bus() fails,
propagate the error to aid debugging.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When device tree support was added the setting of algo_data.reset_chip
was moved. There were two problems with this. The first being that
i2c_pca_pf_resetchip was only used if platform data was provided. The
second that it was unconditionally overridden with
i2c_pca_pf_dummyreset. Ensure that however the reset gpio is defined the
correct reset_chip function is used.
Fixes: commit 4cc7229daa ("i2c: pca-platform: switch to struct gpio_desc")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- Slave mode selected in platform module if the support is detected in
the DT.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- Changes in Kconfig to enable I2C_DESIGNWARE_SLAVE support
- Slave functions added to core library file
- Slave abort sources added to common source file
- New driver: i2c-designware-slave added
- Changes in the Makefile to compile the I2C_DESIGNWARE_SLAVE module
when supported by the architecture.
All the SLAVE flow is added but it is not enabled via platform
driver.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: made a function static and one-lined a message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
0-DAY kernel test reports the following build issue on IA64 architecture
with allmodconfig.
drivers/i2c/busses/i2c-zx2967.c: In function 'zx2967_i2c_writesb':
>> drivers/i2c/busses/i2c-zx2967.c:87:2: error: implicit declaration of function 'writesb' [-Werror=implicit-function-declaration]
writesb(i2c->reg_base + reg, data, len);
^~~~~~~
drivers/i2c/busses/i2c-zx2967.c: In function 'zx2967_i2c_readsb':
>> drivers/i2c/busses/i2c-zx2967.c:93:2: error: implicit declaration of function 'readsb' [-Werror=implicit-function-declaration]
readsb(i2c->reg_base + reg, data, len);
^~~~~~
cc1: some warnings being treated as errors
It's caused by that writesb/readsb are unavailable on IA64 architecture.
Let's drop COMPILE_TEST dependency to avoid the build issue.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Let's always use the platform device for dev_* and not sometimes the
adapter device as well. Also fix this checkpatch check:
CHECK: Macro argument 'i2c' may be better as '(i2c)' to avoid precedence issues
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch to using the devm_ APIs and remove the now unnecessary error
handling and most of the device removal code.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[wsa: adapted error handling I added in previous patch]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow devices that use this driver to be registered via a
devicetree.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[wsa: fixed leakage when registering GPIO failed]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make use of struct gpio_desc which allows us to specify the active state
of the reset pin.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver was clearing the hold bit in the control register before
writing to the address register which resulted in a stop condition
being generated rather than a repeated start.
This issue was only observed when a system was running much
slower than a normal processor would execute. The IP data sheet
mentions a ordering of writing to the address register before
clearing the hold.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Paresh Chaudhary <paresh.chaudhary@rockwellcollins.com>
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds i2c controller driver for ZTE's zx2967 family.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Added slave support for Aspeed I2C controller. Supports fourteen busses
present in AST24XX and AST25XX BMC SoCs by Aspeed.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Added initial master support for Aspeed I2C controller. Supports
fourteen busses present in AST24XX and AST25XX BMC SoCs by Aspeed.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add recent findings (IGNORE_NAK) and document in a bit more detail why
the feature is not possible.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-imx driver incorrectly uses readb()/writeb() to read and
write to the appropriate registers when performing a repeated start.
The appropriate imx_i2c_read_reg()/imx_i2c_write_reg() functions
should be used instead. Performing a repeated start results in
a kernel panic. The platform is imx.
Signed-off-by: Michail G Etairidis <m.etairidis@beck-ipc.com>
Fixes: ce1a78840f ("i2c: imx: add DMA support for freescale i2c driver")
Fixes: 054b62d9f2 ("i2c: imx: fix the i2c bus hang issue when do repeat restart")
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- Definitions were added to core library
- A example was added to designware-core.txt Documentation that shows
how the slave can be setup using DTS
SLAVE related definitions were added to the core of the controller.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Bhumika Goyal