There is no point inlining the 32-bit direct register read/write part,
just infer it from the existing macro. This will make it easier to
centralize the address rewriting that we are going to introduce later
on.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add supporf for the SYSTEMPORT Lite Ethernet controller, this piece of hardware
is largely based on the full-blown SYSTEMPORT and differs in the following:
- no full-blown UniMAC, instead we have the MagicPacket matching from UniMAC at
same offset, and a GMII Interface Block (GIB) for the MAC-level stuff, since
we are always interfaced to an Ethernet switch which is fully Ethernet compliant
shortcuts could be made
- 16 transmit queues, whose interrupts are moved into the first Level-2 interrupt
controller bank
- slight TDMA offset change (a register was inserted after TDMA_STATUS, *sigh*)
- 256 RX descriptors (512 words) and 256 TX descriptors (not visible)
As a consequence of these two things, update the code paths accordingly to
differentiate the full-blown from the light version.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding SYSTEMPORT Lite, which has twice as less transmit
queues than SYSTEMPORT make sure we do allocate TX rings based on the
systemport,txq property to get an appropriate memory footprint.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the LS mask when setting EEE timer.
LS field is 10 bits long and not 11 as currently.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Reported-By: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make the code clearer, use rb_entry() instead of container_of() to
deal with rbtree.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the Marvell mv88e6xxx DSA driver made use of the HWMON support in
DSA. The temperature sensor registers are actually in the embedded
PHYs, and the PHY driver now supports it. So remove all HWMON support
from DSA and drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell PHYs have an inbuilt temperature sensor. Add hwmon
support for this sensor.
There are two different variants. The simpler, older chips have a 5
degree accuracy. The newer devices have 1 degree accuracy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes some updates for mlx5 core and mlx5e netdevice driver.
From Leon, a small fix that remove an unnecessary print.
From Eli Cohen, a fix to the FW version printout in case of internal error.
From Eugenia Emantayev, two patches, the 1st adds mlx5 1pps (pulse per
second) mlx5 infrastructure support and the 2nd adds the necessary bits
for mlx5e ptp logic and structures.
From Mohamad, add support for s-tagged packet receive when in promiscuous
mode.
Form Gal Pressman, MCAM (Management capabilities mask register) and PCAM
(Ports capabilities mask register) registers infrastructure, those
registers are needed in order to query the different statistics registers
support in FW, in order for the driver to enable/disable query and
reporting them back to user. On top of this infrastructure we've exposed
new set of statistics groups:
- MPCNT: Physical layer statistical counters (For symbol errors)
- PPCNT: PCIe performance counters
In addition to the statistics capabilities series we've moved the mlx5 HCA
capabilities fields to a dedicated struct under the driver private data.
At the end a small patch to update & query statistics in the most desired
order.
Thanks,
Saeed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYgT2XAAoJEEg/ir3gV/o++x8H/2adUTYToQVH9T9KdeHYcpYj
LtN36/8WFL5MliMpK0DcmuKe9k45ukN5bJGUDhwndJBsHJledBoFw3C6k4vZl0Qw
NiP4t165xmwYQrqI75KVeeGqNWl6LanozZzJVsOM48mSjOXClPnz5BFR4UgL5gTh
q60VmqpSeBjT0EQfT18s1DZCdUY6UUK1XgmgNnFsHUhO/iWVPlNEwItblC2N/YWA
p7lGUAJmAQvDN2sejzz0ElcCieY8yA+cZHgalW0KZK961RCwIl1GECw5xEcLLGxN
O88jaDvTuJpZtl0IOsBi9dwZHx64dx1a+wkFGv+GA6eTgiQ5kPgb2Jdhy26jf9g=
=Hy/5
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-01-19' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 and mlx5e updates 2017-01-19
This series includes some updates for mlx5 core and mlx5e netdevice driver.
From Leon, a small fix that remove an unnecessary print.
From Eli Cohen, a fix to the FW version printout in case of internal error.
From Eugenia Emantayev, two patches, the 1st adds mlx5 1pps (pulse per
second) mlx5 infrastructure support and the 2nd adds the necessary bits
for mlx5e ptp logic and structures.
From Mohamad, add support for s-tagged packet receive when in promiscuous
mode.
Form Gal Pressman, MCAM (Management capabilities mask register) and PCAM
(Ports capabilities mask register) registers infrastructure, those
registers are needed in order to query the different statistics registers
support in FW, in order for the driver to enable/disable query and
reporting them back to user. On top of this infrastructure we've exposed
new set of statistics groups:
- MPCNT: Physical layer statistical counters (For symbol errors)
- PPCNT: PCIe performance counters
In addition to the statistics capabilities series we've moved the mlx5 HCA
capabilities fields to a dedicated struct under the driver private data.
At the end a small patch to update & query statistics in the most desired
order.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After adding cpsw_set_ringparam ethtool op, better to carry out
common parts of similar ops splitting descriptors in runtime. It
allows to reuse these parts and shows what the ops actually do.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to duplicate the same function in rx handler to get info
if any interface is running.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to create additional vars to identify if interface is running.
So simplify code by removing redundant var and checking usage counter
instead.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to disable interrupts if no open devices,
they are disabled anyway.
Even no need to disable interrupts if some ndev is opened, In this
case shared resources are not touched, only parameters of ndev shell,
so no reason to disable them also. Removed lines have proved it.
So, no need in redundant check and interrupt disable.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Common res usage is possible only in case an interface is
running. In case of not dual emac here can be only one interface,
so while ndo_open and switch mode, only one interface can be opened,
thus if open is called no any interface is running ... and no common
res are used. So remove check on dual emac, it will simplify
code/understanding and will match the name it's called.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_is_rx_handler_busy() check is a superset of netif_is_ipvlan_port()
check and hence should be preferred.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPvlan checks if the master device is already used by checking a
specific device (here it's macvlan device). This is technically not
sufficient and it should just ensure the rx_handler is busy or not.
This would be a super check that includes macvlan and any other that
has already registered rx-handler.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate sparse warning by maintaining type of dst_port
as __be16.
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two new variables are only used inside of an #ifdef and cause
harmless warnings when that is disabled:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c: In function 'init_one':
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4646:9: error: unused variable 'port_vec' [-Werror=unused-variable]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4646:6: error: unused variable 'v' [-Werror=unused-variable]
This adds another #ifdef around the declarations.
Fixes: 96fe11f27b ("cxgb4: Implement ndo_get_phys_port_id for mgmt dev")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 04aeb56a17 ("net/mlx4_en: allocate non 0-order pages for RX
ring with __GFP_NOMEMALLOC") added code that appears to be not needed at
that time, since mlx4 never used __GFP_MEMALLOC allocations anyway.
As using memory reserves is a must in some situations (swap over NFS or
iSCSI), this patch adds this flag.
Note that this driver does not reuse pages (yet) so we do not have to
add anything else.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3e88449344.
With commit 529ed12752 ("net: phy: phy drivers should not set
SUPPORTED_[Asym_]Pause"), phylib now handles automatically enabling
pause frame support in the PHY, and the MAC driver should follow suit.
Since the EMAC driver driver does this, we no longer need to force
pause frames support.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reorder update stats flow to update most important counters last,
to get more accurate results.
New update order:
- PCIe counters
- Port counters
- Vport counters
- Queue counters
- Software counters
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Gal Pressman <galp@mellanox.com>
The caps structure consists of hca caps and port/management caps,
all under one roof.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use ethtool -S to query physical layer statistical counters including:
- rx_symbol_errors_phy: Number of symbol errors that were not corrected
by FEC correction algorithm or that FEC was not active on this interface.
- rx_corrected_bits_phy: Number of corrected bits according to active
FEC (RS/FC).
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On load_one, we now cache our capabilities registers internally, similar
to QUERY_HCA_CAP. Capabilities can later be queried using macros
introduced in this patch.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduced registers will expose capabilities of new registers and
features related to port/management.
Driver will query MCAM and PCAM in order to avoid failing on old
firmwares with lack of support.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Today when the driver enter to promiscuous mode or vlan
filter is disabled, we add flow rule to receive any c-taggd
packets, therefore s-tagged packets are dropped.
In order to receive s-tagged packets as well we need to add
flow rule to receive any s-tagged packet.
Fixes: 7cb21b794b ('net/mlx5e: Rename en_flow_table.c to en_fs.c')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch enables the 1PPS IN and 1PPS OUT support according
to the advertised HCA capability. Single pin may be configured
to one of the above mutual exclusive functions via standard
Linux tools and APIs. For example, testptp open source application.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Implement query and set functionality for MTPPS and MTPPSE registers.
MTPPS (Management Pulse Per Second) provides the device PPS capabilities,
configures the PPS in and out modules and holds the PPS in time stamp.
Query MTPPS is supported only when HCA_CAP.pps is set and modify is supported
when HCA_CAP.pps_modify is set.
MTPPSE (Management Pulse Per Second Event) configures the different event
generation modes for PPS. Supported when HCA_CAP.pps is set.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Firmware representation of the firmware version on the health buffer has
changed for newer device. The representation in the initialization
segment does not and will not change. In addition, we print the health
buffer firmware version as a raw hex number.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Infiniband part of mlx5 driver can be compiled as a module
or as a part of bzImage (compiled in). In the second case,
the call to request_module will return an error -ENOENT.
It will cause to a misleading print "failed request module
on mlx5_ib".
This patch removes this print, In order to comply with mlx4.
Fixes: f66f049fb7 ("net/mlx5_core: Request the mlx5 IB module on driver load")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch does the following:
- MACB/GEM-PTP interface
- registers and bitfields for TSU
- capability flags to enable PTP per platform basis
Signed-off-by: Andrei Pistirica <andrei.pistirica@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network stack no longer uses the last_rx member of struct net_device
since the bonding driver switched to use its own private last_rx in
commit 9f24273837 ("bonding: use last_arp_rx in slave_last_rx()").
However, some drivers still (ab)use the field for their own purposes and
some driver just update it without actually using it.
Previously, there was an accompanying comment for the last_rx member
added in commit 4dc89133f4 ("net: add a comment on netdev->last_rx")
which asked drivers not to update is, unless really needed. However,
this commend was removed in commit f8ff080dac ("bonding: remove
useless updating of slave->dev->last_rx"), so some drivers added later
on still did update last_rx.
Remove all usage of last_rx and switch three drivers (sky2, atp and
smc91c92_cs) which actually read and write it to use their own private
copy in netdev_priv.
Compile-tested with allyesconfig and allmodconfig on x86 and arm.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check "ch" on NULL first, then get ctlr.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can only process 1 packet at one time during sendmsg(). This often
lead bad cache utilization under heavy load. So this patch tries to do
some batching during rx before submitting them to host network
stack. This is done through accepting MSG_MORE as a hint from
sendmsg() caller, if it was set, batch the packet temporarily in a
linked list and submit them all once MSG_MORE were cleared.
Tests were done by pktgen (burst=128) in guest over mlx4(noqueue) on host:
Mpps -+%
rx-frames = 0 0.91 +0%
rx-frames = 4 1.00 +9.8%
rx-frames = 8 1.00 +9.8%
rx-frames = 16 1.01 +10.9%
rx-frames = 32 1.07 +17.5%
rx-frames = 48 1.07 +17.5%
rx-frames = 64 1.08 +18.6%
rx-frames = 64 (no MSG_MORE) 0.91 +0%
User were allowed to change per device batched packets through
ethtool -C rx-frames. NAPI_POLL_WEIGHT were used as upper limitation
to prevent bh from being disabled too long.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Relax ordering(RO) is one feature of 82599 NIC, to enable this feature can
enhance the performance for some cpu architecure, such as SPARC and so on.
Currently it only supports one special cpu architecture(SPARC) in 82599
driver to enable RO feature, this is not very common for other cpu architecture
which really needs RO feature.
This patch add one common config CONFIG_ARCH_WANT_RELAX_ORDER to set RO feature,
and should define CONFIG_ARCH_WANT_RELAX_ORDER in sparc Kconfig firstly.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Alexander Duyck <alexander.duyck@gmail.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds more info to stmicro' Kconfig files in order to be clearer
that the driver can be used by ethernet cards based on 10/100/1000/EQOS
Synopsys IP Cores.
EQOS was also added stmmac/Kconfig Kconfig, since dwmac4 is in fact EQoS,
one of Synopsys Ethernet IPs. More info at:
https://www.synopsys.com/dw/ipdir.php?ds=dwc_ether_qos
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds bpf_xdp_adjust_head() support to mlx5e.
1. rx_headroom is added to struct mlx5e_rq. It uses
an existing 4 byte hole in the struct.
2. The adjusted data length is checked against
MLX5E_XDP_MIN_INLINE and MLX5E_SW2HW_MTU(rq->netdev->mtu).
3. The macro MLX5E_SW2HW_MTU is moved from en_main.c to en.h.
MLX5E_HW2SW_MTU is also moved to en.h for symmetric reason
but it is not a must.
v2:
- Keep the xdp specific logic in mlx5e_xdp_handle()
- Update dma_len after the sanity checks in mlx5e_xmit_xdp_frame()
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the needlessly global struct ethtool_ops ethoc_ethtool_ops static
to fix a sparse warning.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensures that we report the key and indirection table the NIC is using,
rather than (if setting them failed earlier) what we wanted it to use.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_zero_addr to assign zero address to the given address array
instead of memset when the second argument in memset is address
of zero. Also, it makes the code clearer
Signed-off-by: Shyam Saini <mayhs11saini@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function stmmac_dt_phy provides several possibilities for initializing
plat->mdio_node, all of which have the effect of increasing the reference
count of the assigned value. This field is not updated elsewhere, so the
value is live until the end of the lifetime of plat (devm_allocated), just
after the end of stmmac_remove_config_dt. Thus, add an of_node_put on
plat->mdio_node in stmmac_remove_config_dt. It is possible that the field
mdio_node is never initialized, but of_node_put is NULL-safe, so it is also
safe to call of_node_put in that case.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
The callback set_link_ksettings no longer update the value
of advertising, as the struct ethtool_link_ksettings is
defined as const.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tests showed that when whole bandwidth is consumed, the latency for
various kind of traffic can reach high values. With saturated
link (e.g. with iperf from target to host) simple ping could take
significant amount of time. BQL proved to improve this situation
when implemented in mvneta driver. Measurements of ping latency
for 3 link speeds:
Speed | Latency w/o BQL | Latency with BQL
10 | 7-14 ms | 3.5 ms
100 | 2-12 ms | 0.6 ms
1000 | often timeout | up to 2ms
Decreasing latency as above result in sligt performance cost - 4kpps
(-1.4%) when pushing 64B packets via two bridged interfaces of Armada 38x.
For 1500B packets in the same setup, the mpstat tool showed +8% of
CPU occupation (default affinity, second CPU idle). Even though this
cost seems reasonable to take, considering other improvements.
This commit adds byte queue limit mechanism for the mvneta driver.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli