This patch adds a check in chap_server_compute_md5() to enforce a
1024 byte maximum for the CHAP_C key value following the requirement
in RFC-3720 Section 11.1.4:
"..., C and R are large-binary-values and their binary length (not
the length of the character string that represents them in encoded
form) MUST not exceed 1024 bytes."
Reported-by: rahul.rane <rahul.rane@calsoftinc.com>
Tested-by: rahul.rane <rahul.rane@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts chap_server_compute_md5() from simple_strtoul() to
kstrtoul usage().
This addresses the case where a empty 'CHAP_I=' key value received during
mutual authentication would be converted to a '0' by simple_strtoul(),
instead of failing the login attempt.
Reported-by: Tejas Vaykole <tejas.vaykole@calsoftinc.com>
Tested-by: Tejas Vaykole <tejas.vaykole@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Add support for T10 PI pass-through between vhost-scsi +
virtio-scsi (MST + Paolo + MKP + nab)
- Add support for T10 PI in qla2xxx target mode (Quinn + MKP + hch +
nab, merged through scsi.git)
- Add support for percpu-ida pre-allocation in qla2xxx target code
(Quinn + nab)
- A number of iser-target fixes related to hardening the network
portal shutdown path (Sagi + Slava)
- Fix response length residual handling for a number of control CDBs
(Roland + Christophe V.)
- Various iscsi RFC conformance fixes in the CHAP authentication path
(Tejas and Calsoft folks + nab)
- Return TASK_SET_FULL status for tcm_fc(FCoE) DataIn + Response
failures (Vasu + Jun + nab)
- Fix long-standing ABORT_TASK + session reset hang (nab)
- Convert iser-initiator + iser-target to include T10 bytes into EDTL
(Sagi + Or + MKP + Mike Christie)
- Fix NULL pointer dereference regression related to XCOPY introduced
in v3.15 + CC'ed to v3.12.y (nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (34 commits)
target: Fix NULL pointer dereference for XCOPY in target_put_sess_cmd
vhost-scsi: Include prot_bytes into expected data transfer length
TARGET/sbc,loopback: Adjust command data length in case pi exists on the wire
libiscsi, iser: Adjust data_length to include protection information
scsi_cmnd: Introduce scsi_transfer_length helper
target: Report correct response length for some commands
target/sbc: Check that the LBA and number of blocks are correct in VERIFY
target/sbc: Remove sbc_check_valid_sectors()
Target/iscsi: Fix sendtargets response pdu for iser transport
Target/iser: Fix a wrong dereference in case discovery session is over iser
iscsi-target: Fix ABORT_TASK + connection reset iscsi_queue_req memory leak
target: Use complete_all for se_cmd->t_transport_stop_comp
target: Set CMD_T_ACTIVE bit for Task Management Requests
target: cleanup some boolean tests
target/spc: Simplify INQUIRY EVPD=0x80
tcm_fc: Generate TASK_SET_FULL status for response failures
tcm_fc: Generate TASK_SET_FULL status for DataIN failures
iscsi-target: Reject mutual authentication with reflected CHAP_C
iscsi-target: Remove no-op from iscsit_tpg_del_portal_group
iscsi-target: Fix CHAP_A parameter list handling
...
This patch fixes a NULL pointer dereference regression bug that was
introduced with:
commit 1e1110c43b
Author: Mikulas Patocka <mpatocka@redhat.com>
Date: Sat May 17 06:49:22 2014 -0400
target: fix memory leak on XCOPY
Now that target_put_sess_cmd() -> kref_put_spinlock_irqsave() is
called with a valid se_cmd->cmd_kref, a NULL pointer dereference
is triggered because the XCOPY passthrough commands don't have
an associated se_session pointer.
To address this bug, go ahead and checking for a NULL se_sess pointer
within target_put_sess_cmd(), and call se_cmd->se_tfo->release_cmd()
to release the XCOPY's xcopy_pt_cmd memory.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # 3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In various areas of the code, it is assumed that
se_cmd->data_length describes pure data. In case
that protection information exists over the wire
(protect bits is are on) the target core re-calculates
the data length from the CDB and the backed device
block size (instead of each transport peeking in the cdb).
Modify loopback device to include protection information
in the transferred data length (like other scsi transports).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: stable@vger.kernel.org # 3.15+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When an initiator sends an allocation length bigger than what its
command consumes, the target should only return the actual response data
and set the residual length to the unused part of the allocation length.
Add a helper function that command handlers (INQUIRY, READ CAPACITY,
etc) can use to do this correctly, and use this code to get the correct
residual for commands that don't use the full initiator allocation in the
handlers for READ CAPACITY, READ CAPACITY(16), INQUIRY, MODE SENSE and
REPORT LUNS.
This addresses a handful of failures as reported by Christophe with
the Windows Certification Kit:
http://permalink.gmane.org/gmane.linux.scsi.target.devel/6515
Signed-off-by: Roland Dreier <roland@purestorage.com>
Tested-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch extracts LBA + sectors for VERIFY, and adds a goto check_lba
to perform the end-of-device checking.
(Update patch to drop lba_check usage - nab)
Signed-off-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
A similar check is performed at the end of sbc_parse_cdb() and is now
enforced if the SYNCHRONIZE CACHE command's backend supports
->execute_sync_cache().
(Add check_lba goto to avoid *_max_sectors checks - nab)
Signed-off-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case the transport is iser we should not include the
iscsi target info in the sendtargets text response pdu.
This causes sendtargets response to include the target
info twice.
Modify iscsit_build_sendtargets_response to filter
transport types that don't match.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reported-by: Slava Shwartsman <valyushash@gmail.com>
Cc: stable@vger.kernel.org # 3.11+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull block layer fixes from Jens Axboe:
"Final small batch of fixes to be included before -rc1. Some general
cleanups in here as well, but some of the blk-mq fixes we need for the
NVMe conversion and/or scsi-mq. The pull request contains:
- Support for not merging across a specified "chunk size", if set by
the driver. Some NVMe devices perform poorly for IO that crosses
such a chunk, so we need to support it generically as part of
request merging avoid having to do complicated split logic. From
me.
- Bump max tag depth to 10Ki tags. Some scsi devices have a huge
shared tag space. Before we failed with EINVAL if a too large tag
depth was specified, now we truncate it and pass back the actual
value. From me.
- Various blk-mq rq init fixes from me and others.
- A fix for enter on a dying queue for blk-mq from Keith. This is
needed to prevent oopsing on hot device removal.
- Fixup for blk-mq timer addition from Ming Lei.
- Small round of performance fixes for mtip32xx from Sam Bradshaw.
- Minor stack leak fix from Rickard Strandqvist.
- Two __init annotations from Fabian Frederick"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: add __init to blkcg_policy_register
block: add __init to elv_register
block: ensure that bio_add_page() always accepts a page for an empty bio
blk-mq: add timer in blk_mq_start_request
blk-mq: always initialize request->start_time
block: blk-exec.c: Cleaning up local variable address returnd
mtip32xx: minor performance enhancements
blk-mq: ->timeout should be cleared in blk_mq_rq_ctx_init()
blk-mq: don't allow queue entering for a dying queue
blk-mq: bump max tag depth to 10K tags
block: add blk_rq_set_block_pc()
block: add notion of a chunk size for request merging
This patch fixes a iscsi_queue_req memory leak when ABORT_TASK response
has been queued by TFO->queue_tm_rsp() -> lio_queue_tm_rsp() after a
long standing I/O completes, but the connection has already reset and
waiting for cleanup to complete in iscsit_release_commands_from_conn()
-> transport_generic_free_cmd() -> transport_wait_for_tasks() code.
It moves iscsit_free_queue_reqs_for_conn() after the per-connection command
list has been released, so that the associated se_cmd tag can be completed +
released by target-core before freeing any remaining iscsi_queue_req memory
for the connection generated by lio_queue_tm_rsp().
Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Charalampos Pournaris <charpour@gmail.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug where multiple waiters on ->t_transport_stop_comp
occurs due to a concurrent ABORT_TASK and session reset both invoking
transport_wait_for_tasks(), while waiting for the associated se_cmd
descriptor backend processing to complete.
For this case, complete_all() should be invoked in order to wake up
both waiters in core_tmr_abort_task() + transport_generic_free_cmd()
process contexts.
Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Charalampos Pournaris <charpour@gmail.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug where se_cmd descriptors associated with a
Task Management Request (TMR) where not setting CMD_T_ACTIVE before
being dispatched into target_tmr_work() process context.
This is required in order for transport_generic_free_cmd() ->
transport_wait_for_tasks() to wait on se_cmd->t_transport_stop_comp
if a session reset event occurs while an ABORT_TASK is outstanding
waiting for another I/O to complete.
Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Charalampos Pournaris <charpour@gmail.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that 3.15 is released, this merges the 'next' branch into 'master',
bringing us to the normal situation where my 'master' branch is the
merge window.
* accumulated work in next: (6809 commits)
ufs: sb mutex merge + mutex_destroy
powerpc: update comments for generic idle conversion
cris: update comments for generic idle conversion
idle: remove cpu_idle() forward declarations
nbd: zero from and len fields in NBD_CMD_DISCONNECT.
mm: convert some level-less printks to pr_*
MAINTAINERS: adi-buildroot-devel is moderated
MAINTAINERS: add linux-api for review of API/ABI changes
mm/kmemleak-test.c: use pr_fmt for logging
fs/dlm/debug_fs.c: replace seq_printf by seq_puts
fs/dlm/lockspace.c: convert simple_str to kstr
fs/dlm/config.c: convert simple_str to kstr
mm: mark remap_file_pages() syscall as deprecated
mm: memcontrol: remove unnecessary memcg argument from soft limit functions
mm: memcontrol: clean up memcg zoneinfo lookup
mm/memblock.c: call kmemleak directly from memblock_(alloc|free)
mm/mempool.c: update the kmemleak stack trace for mempool allocations
lib/radix-tree.c: update the kmemleak stack trace for radix tree allocations
mm: introduce kmemleak_update_trace()
mm/kmemleak.c: use %u to print ->checksum
...
Convert "x == true" to "x" and "x == false" to "!x".
Signed-off-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes ft_queue_status() to set SAM_STAT_TASK_SET_FULL
status upon lport->tt.seq_send( failure, and return -EAGAIN to notify
target-core to attempt to requeue the response.
It also does the same for a fc_frame_alloc() failures, in order to
signal the initiator that it should try to reduce it's current
queue_depth, to lower the number of outstanding I/Os on the wire.
Reported-by: Vasu Dev <vasu.dev@linux.intel.com>
Reviewed-by: Vasu Dev <vasu.dev@linux.intel.com>
Cc: Jun Wu <jwu@stormojo.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes ft_queue_data_in() to set SAM_STAT_TASK_SET_FULL
status upon a lport->tt.seq_send() failure, where it will now stop
sending subsequent DataIN, and immediately attempt to send the
response with exception status.
Sending a response with SAM_STAT_TASK_SET_FULL status is useful in
order to signal the initiator that it should try to reduce it's
current queue_depth, to lower the number of outstanding I/Os on
the wire.
Also, add a check to skip sending DataIN if TASK_SET_FULL status
has already been set due to a response lport->tt.seq_send()
failure, that has asked target-core to requeue a response.
Reported-by: Vasu Dev <vasu.dev@linux.intel.com>
Reviewed-by: Vasu Dev <vasu.dev@linux.intel.com>
Cc: Jun Wu <jwu@stormojo.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
With the optimizations around not clearing the full request at alloc
time, we are leaving some of the needed init for REQ_TYPE_BLOCK_PC
up to the user allocating the request.
Add a blk_rq_set_block_pc() that sets the command type to
REQ_TYPE_BLOCK_PC, and properly initializes the members associated
with this type of request. Update callers to use this function instead
of manipulating rq->cmd_type directly.
Includes fixes from Christoph Hellwig <hch@lst.de> for my half-assed
attempt.
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch fixes a OOPs where an attempt to write to the per-device
alua_access_state configfs attribute at:
/sys/kernel/config/target/core/$HBA/$DEV/alua/$TG_PT_GP/alua_access_state
results in an NULL pointer dereference when the backend device has not
yet been configured.
This patch adds an explicit check for DF_CONFIGURED, and fails with
-ENODEV to avoid this case.
Reported-by: Chris Boot <crb@tiger-computing.co.uk>
Reported-by: Philip Gaw <pgaw@darktech.org.uk>
Cc: Chris Boot <crb@tiger-computing.co.uk>
Cc: Philip Gaw <pgaw@darktech.org.uk>
Cc: stable@vger.kernel.org # 3.8+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch allows READ_CAPACITY + SAI_READ_CAPACITY_16 opcode
processing to occur while the associated ALUA group is in Standby
access state.
This is required to avoid host side LUN probe failures during the
initial scan if an ALUA group has already implicitly changed into
Standby access state.
This addresses a bug reported by Chris + Philip using dm-multipath
+ ESX hosts configured with ALUA multipath.
Reported-by: Chris Boot <crb@tiger-computing.co.uk>
Reported-by: Philip Gaw <pgaw@darktech.org.uk>
Cc: Chris Boot <crb@tiger-computing.co.uk>
Cc: Philip Gaw <pgaw@darktech.org.uk>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds an explicit check in chap_server_compute_md5() to ensure
the CHAP_C value received from the initiator during mutual authentication
does not match the original CHAP_C provided by the target.
This is in line with RFC-3720, section 8.2.1:
Originators MUST NOT reuse the CHAP challenge sent by the Responder
for the other direction of a bidirectional authentication.
Responders MUST check for this condition and close the iSCSI TCP
connection if it occurs.
Reported-by: Tejas Vaykole <tejas.vaykole@calsoftinc.com>
Cc: stable@vger.kernel.org # 3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes a no-op iscsit_clear_tpg_np_login_threads() call
in iscsit_tpg_del_portal_group(), which is unnecessary because
iscsit_tpg_del_portal_group() can only ever be removed from configfs
once all of the child network portals have been released.
Also, go ahed and make iscsit_clear_tpg_np_login_threads() declared
as static.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The target is failing to handle list of CHAP_A key-value pair form
initiator.The target is expecting CHAP_A=5 always. In other cases,
where initiator sends list (for example) CHAP_A=6,5 target is failing
the security negotiation. Which is incorrect.
This patch handles the case (RFC 3720 section 11.1.4).
where in the initiator may send list of CHAP_A values and target replies
with appropriate CHAP_A value in response
(Drop whitespaces + rename to chap_check_algorithm + save original
pointer + add explicit check for CHAP_A key - nab)
Signed-off-by: Tejas Vaykole <tejas.vaykole@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If the message "Unable to allocate…" pops up, it's useful to know
whether the problem is that the system is genuinely out of memory, or
that some bug has led to a crazy allocation length.
In particular this helped debug a corruption of login headers in
iscsi_login_non_zero_tsih_s1().
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes iscsi_target_handle_csg_zero() to explicitly
reject login requests in SecurityNegotiation with a zero-length
payload, following the language in RFC-3720 Section 8.2:
Whenever an iSCSI target gets a response whose keys, or their
values, are not according to the step definition, it MUST answer
with a Login reject with the "Initiator Error" or "Missing Parameter"
status.
Previously when a zero-length login request in CSG=0 was received,
the target would send a login response with CSG=0 + T_BIT=0 asking
the initiator to complete authentication, and not fail the login
until MAX_LOGIN_PDUS was reached. This change will now immediately
fail the login attempt with ISCSI_STATUS_CLS_INITIATOR_ERR status.
Reported-by: Tejas Vaykole <tejas.vaykole@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a iser-target specific regression introduced in
v3.15-rc6 with:
commit 14f4b54fe3
Author: Sagi Grimberg <sagig@mellanox.com>
Date: Tue Apr 29 13:13:47 2014 +0300
Target/iscsi,iser: Avoid accepting transport connections during stop stage
where the change to set iscsi_np->enabled = false within
iscsit_clear_tpg_np_login_thread() meant that a iscsi_np with
two iscsi_tpg_np exports would have it's parent iscsi_np set
to a disabled state, even if other iscsi_tpg_np exports still
existed.
This patch changes iscsit_clear_tpg_np_login_thread() to only
set iscsi_np->enabled = false when shutdown = true, and also
changes iscsit_del_np() to set iscsi_np->enabled = true when
iscsi_np->np_exports is non zero.
Cc: Sagi Grimberg <sagig@dev.mellanox.co.il>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In non-leading connection login, iscsi_login_non_zero_tsih_s1() calls
iscsi_change_param_value() with the buffer it uses to hold the login
PDU, not a temporary buffer. This leads to the login header getting
corrupted and login failing for non-leading connections in MC/S.
Fix this by adding a wrapper iscsi_change_param_sprintf() that handles
the temporary buffer itself to avoid confusion. Also handle sending a
reject in case of failure in the wrapper, which lets the calling code
get quite a bit smaller and easier to read.
Finally, bump the size of the temporary buffer from 32 to 64 bytes to be
safe, since "MaxRecvDataSegmentLength=" by itself is 25 bytes; with a
trailing NUL, a value >= 1M will lead to a buffer overrun. (This isn't
the default but we don't need to run right at the ragged edge here)
Reported-by: Santosh Kulkarni <santosh.kulkarni@calsoftinc.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
On each processed XCOPY command, two "kmalloc-512" memory objects are
leaked. These represent two allocations of struct xcopy_pt_cmd in
target_core_xcopy.c.
The reason for the memory leak is that the cmd_kref field is not
initialized (thus, it is zero because the allocations were done with
kzalloc). When we decrement zero kref in target_put_sess_cmd, the result
is not zero, thus target_release_cmd_kref is not called.
This patch fixes the bug by moving kref initialization from
target_get_sess_cmd to transport_init_se_cmd (this function is called from
target_core_xcopy.c, so it will correctly initialize cmd_kref). It can be
easily verified that all code that calls target_get_sess_cmd also calls
transport_init_se_cmd earlier, thus moving kref_init shouldn't introduce
any new problems.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # 3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Just like for pSCSI, if the transport sets get_write_cache, then it is
not valid to enable write cache emulation for it. Return an error.
see https://bugzilla.redhat.com/show_bug.cgi?id=1082675
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch explicitly disables Immediate + Unsolicited Data for ISER
connections during login in iscsi_login_zero_tsih_s2() when protection
has been enabled for the session by the underlying hardware.
This is currently required because protection / signature memory regions
(MRs) expect T10 PI to occur on RDMA READs + RDMA WRITEs transfers, and
not on a immediate data payload associated with ISCSI_OP_SCSI_CMD, or
unsolicited data-out associated with a ISCSI_OP_SCSI_DATA_OUT.
v2 changes:
- Add TARGET_PROT_DOUT_INSERT check (Sagi)
- Add pr_debug noisemaker (Sagi)
- Add goto to avoid early return from MRDSL check (nab)
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a free-after-use regression in ft_free_cmd(), where
ft_sess_put() is called with cmd->sess after percpu_ida_free() has
already released the tag.
Fix this bug by saving the ft_sess pointer ahead of percpu_ida_free(),
and pass it directly to ft_sess_put().
The regression was originally introduced in v3.13-rc1 commit:
commit 5f544cfac9
Author: Nicholas Bellinger <nab@daterainc.com>
Date: Mon Sep 23 12:12:42 2013 -0700
tcm_fc: Convert to per-cpu command map pre-allocation of ft_cmd
Reported-by: Jun Wu <jwu@stormojo.com>
Cc: Mark Rustad <mark.d.rustad@intel.com>
Cc: Robert Love <robert.w.love@intel.com>
Cc: <stable@vger.kernel.org> #3.13+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes an incorrect use of BUG_ON to instead generate a
REJECT + PROTOCOL_ERROR in iscsit_process_nop_out() code. This case
can occur with traditional TCP where a flood of zeros in the data
stream can reach this block for what is presumed to be a NOP-OUT with
a solicited reply, but without a valid iscsi_cmd pointer.
This incorrect BUG_ON was introduced during the v3.11-rc timeframe
with the following commit:
commit 778de36896
Author: Nicholas Bellinger <nab@linux-iscsi.org>
Date: Fri Jun 14 16:07:47 2013 -0700
iscsi/isert-target: Refactor ISCSI_OP_NOOP RX handling
Reported-by: Arshad Hussain <arshad.hussain@calsoftinc.com>
Cc: stable@vger.kernel.org # 3.11+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When the target is in stop stage, iSER transport initiates RDMA disconnects.
The iSER initiator may wish to establish a new connection over the
still existing network portal. In this case iSER transport should not
accept and resume new RDMA connections. In order to learn that, iscsi_np
is added with enabled flag so the iSER transport can check when deciding
weather to accept and resume a new connection request.
The iscsi_np is enabled after successful transport setup, and disabled
before iscsi_np login threads are cleaned up.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Userspace tools assume if a value is read from configfs, it is valid
and will not cause an error if the same value is written back. The only
valid value for pi_prot_type for backends not supporting DIF is 0, so allow
this particular value to be set without returning an error.
Reported-by: Krzysztof Chojnowski <frirajder@gmail.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull yet more networking updates from David Miller:
1) Various fixes to the new Redpine Signals wireless driver, from
Fariya Fatima.
2) L2TP PPP connect code takes PMTU from the wrong socket, fix from
Dmitry Petukhov.
3) UFO and TSO packets differ in whether they include the protocol
header in gso_size, account for that in skb_gso_transport_seglen().
From Florian Westphal.
4) If VLAN untagging fails, we double free the SKB in the bridging
output path. From Toshiaki Makita.
5) Several call sites of sk->sk_data_ready() were referencing an SKB
just added to the socket receive queue in order to calculate the
second argument via skb->len. This is dangerous because the moment
the skb is added to the receive queue it can be consumed in another
context and freed up.
It turns out also that none of the sk->sk_data_ready()
implementations even care about this second argument.
So just kill it off and thus fix all these use-after-free bugs as a
side effect.
6) Fix inverted test in tcp_v6_send_response(), from Lorenzo Colitti.
7) pktgen needs to do locking properly for LLTX devices, from Daniel
Borkmann.
8) xen-netfront driver initializes TX array entries in RX loop :-) From
Vincenzo Maffione.
9) After refactoring, some tunnel drivers allow a tunnel to be
configured on top itself. Fix from Nicolas Dichtel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
vti: don't allow to add the same tunnel twice
gre: don't allow to add the same tunnel twice
drivers: net: xen-netfront: fix array initialization bug
pktgen: be friendly to LLTX devices
r8152: check RTL8152_UNPLUG
net: sun4i-emac: add promiscuous support
net/apne: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
net: ipv6: Fix oif in TCP SYN+ACK route lookup.
drivers: net: cpsw: enable interrupts after napi enable and clearing previous interrupts
drivers: net: cpsw: discard all packets received when interface is down
net: Fix use after free by removing length arg from sk_data_ready callbacks.
Drivers: net: hyperv: Address UDP checksum issues
Drivers: net: hyperv: Negotiate suitable ndis version for offload support
Drivers: net: hyperv: Allocate memory for all possible per-pecket information
bridge: Fix double free and memory leak around br_allowed_ingress
bonding: Remove debug_fs files when module init fails
i40evf: program RSS LUT correctly
i40evf: remove open-coded skb_cow_head
ixgb: remove open-coded skb_cow_head
igbvf: remove open-coded skb_cow_head
...
Because it doesn't always create, if there's an existing one it just
returns it.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
These functions are not adding or deleting an lport. They are adding a
wwn that may match with an lport that is present on the system.
Renaming ft_del_lport also means we won't have functions named
both ft_del_lport and ft_lport_del any more.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Rename struct ft_lport_acl to ft_lport_wwn. "acl" is associated with
something different in LIO terms. Really, ft_lport_wwn is the
fabric-specific wrapper for the struct se_wwn.
Rename "lacl" local variables to "ft_wwn" as well.
Rename list_heads used as list members to make it clear they're nodes, not
heads.
Rename lport_node to ft_wwn_node.
Rename ft_lport_list to ft_wwn_list
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
tcm_fc doesn't support multiple TPGs per wwn. For proof, see
ft_lport_find_tpg. Enforce this in the code.
Replace ft_lport_wwn.tpg_list with a single pointer. We can't fold ft_tpg
into ft_lport_wwn because they can have different lifetimes.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
ft_del_tpg checks tpg->tport is set before unlinking the tpg from the
tport when the tpg is being removed. Set this pointer in ft_tport_create,
or the unlinking won't happen in ft_del_tpg and tport->tpg will reference
a deleted object.
This patch sets tpg->tport in ft_tport_create, because that's what
ft_del_tpg checks, and is the only way to get back to the tport to
clear tport->tpg.
The bug was occuring when:
- lport created, tport (our per-lport, per-provider context) is
allocated.
tport->tpg = NULL
- tpg created
- a PRLI is received. ft_tport_create is called, tpg is found and
tport->tpg is set
- tpg removed. ft_tpg is freed in ft_del_tpg. Since tpg->tport was not
set, tport->tpg is not cleared and points at freed memory
- Future calls to ft_tport_create return tport via first conditional,
instead of searching for new tpg by calling ft_lport_find_tpg.
tport->tpg is still invalid, and will access freed memory.
see https://bugzilla.redhat.com/show_bug.cgi?id=1071340
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses an issue that occurs when an ABTS is received
for an se_cmd that completes just before the sess_cmd_list is searched
in core_tmr_abort_task(). When the sess_cmd_list is searched, since
the ABTS and the FCP_CMND being aborted (that just completed) both
have the same OXID, TFO->get_task_tag(TMR) returns a value that
matches tmr->ref_task_tag (from TFO->get_task_tag(FCP_CMND)), and
the Abort Task tries to abort itself. When this occurs,
transport_wait_for_tasks() hangs forever since the TMR is waiting
for itself to finish.
This patch adds a check to core_tmr_abort_task() to make sure the
TMR does not attempt to abort itself.
Signed-off-by: Alex Leung <alex.leung@emulex.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Several spots in the kernel perform a sequence like:
skb_queue_tail(&sk->s_receive_queue, skb);
sk->sk_data_ready(sk, skb->len);
But at the moment we place the SKB onto the socket receive queue it
can be consumed and freed up. So this skb->len access is potentially
to freed up memory.
Furthermore, the skb->len can be modified by the consumer so it is
possible that the value isn't accurate.
And finally, no actual implementation of this callback actually uses
the length argument. And since nobody actually cared about it's
value, lots of call sites pass arbitrary values in such as '0' and
even '1'.
So just remove the length argument from the callback, that way there
is no confusion whatsoever and all of these use-after-free cases get
fixed as a side effect.
Based upon a patch by Eric Dumazet and his suggestion to audit this
issue tree-wide.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the use of READ_STRIP software emulation in
target_complete_ok_work() code for I/O READs.
This is useful when the fabric does not support READ_STRIP hardware
offload, but would still like to interact with backend device
that have T10 PI enabled.
v2 changes:
- Move TARGET_PROT_DIN_STRIP check from target_check_read_strip()
into target_complete_ok_work() (Sagi)
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Split up __sbc_dif_verify_read() so that VERIFY READ emulation can
perform target-core specific READ_STRIP, seperate from the existing
FILEIO/RAMDISK backend emulation code.
Also add sbc_dif_read_strip() in order to determine number of sectors
using cmd->prot_length, and skip the extra sbc_dif_copy_prot().
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch enables WRITE_INSERT emulation in target_execute_cmd()
in order to locally generate DIF PI before submitting the WRITE
to the underlying backend device.
This is required for fabric drivers that currently don't support
DIF over-the-wire, in order to inact with backend devices that
have hardware (IBLOCK) or software (FILEIO + RAMDISK) support
for handling T10 PI.
v2 changes:
- Convert to sbc_dif_generate() usage (Sagi)
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds WRITE_INSERT emulation within target-core
using TYPE1 / TYPE3 PI modes in sbc_dif_generate() code.
This is useful in order for existing legacy fabrics that do not
support protection offloads to interact with backend devices that
currently have T10 PI enabled.
v2 changes:
- Rename to sbc_dif_generate() (Sagi)
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Only expose the PI protection type bits in READ_CAPACITY_16
if the session + fabric support DIX PASS operations.
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Only expose the control modepage bit for Application Tag Owner (ATO)
if the session + fabric support DIX PASS operations.
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Only expose standard INQUIRY PROTECT=1 and EVPD=0x86 TYPE1/TYPE3
PI control bits if the session + fabric support DIX PASS operations.
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In order to support local WRITE_INSERT + READ_STRIP operations for
non PI enabled fabrics, the fabric driver needs to be able signal
what protection offload operations are supported.
This is done at session initialization time so the modes can be
signaled by individual se_wwn + se_portal_group endpoints, as well
as optionally across different transports on the same endpoint.
For iser-target, set TARGET_PROT_ALL if the underlying ib_device
has already signaled PI offload support, and allow this to be
exposed via a new iscsit_transport->iscsit_get_sup_prot_ops()
callback.
For loopback, set TARGET_PROT_ALL to signal SCSI initiator mode
operation.
For all other drivers, set TARGET_PROT_NORMAL to disable fabric
level PI.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a double free bug during IBLOCK backend shutdown
where bioset_integrity_free() was incorrectly called ahead of
bioset_free(), who is already making the same call directly.
This bug was introduced with commit ecebbf6cc, and will end up
triggering a general protection fault in iblock_free_device()
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: <stable@vger.kernel.org> #3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When compiled with CONFIG_DEBUG_SG set, uninitialized SGL leads
to BUG() in compare_and_write_callback().
Signed-off-by: Martin Svec <martin.svec@zoner.cz>
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Ram disk is allocating 8x more space than required for diff data.
For large RAM disk test, there is small potential for memory
starvation.
(Use block_size when calculating total_sg_needed - sagi + nab)
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Cc: <stable@vger.kernel.org> #3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a long-standing bug in iscsit_build_conn_drop_async_message()
where during ERL=2 connection recovery, a bogus conn_p pointer could
end up being used to send the ISCSI_OP_ASYNC_EVENT + DROPPING_CONNECTION
notifying the initiator that cmd->logout_cid has failed.
The bug was manifesting itself as an OOPs in iscsit_allocate_cmd() with
a bogus conn_p pointer in iscsit_build_conn_drop_async_message().
Reported-by: Arshad Hussain <arshad.hussain@calsoftinc.com>
Reported-by: santosh kulkarni <santosh.kulkarni@calsoftinc.com>
Cc: <stable@vger.kernel.org> #3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that TASK_ABORTED status is not generated for all cases by
TMR ABORT_TASK + LUN_RESET, a new TFO->abort_task() caller is
necessary in order to give fabric drivers a chance to unmap
hardware / software resources before the se_cmd descriptor is
released via the normal TFO->release_cmd() codepath.
This patch adds TFO->aborted_task() in core_tmr_abort_task()
in place of the original transport_send_task_abort(), and
also updates all fabric drivers to implement this caller.
The fabric drivers that include changes to perform cleanup
via ->aborted_task() are:
- iscsi-target
- iser-target
- srpt
- tcm_qla2xxx
The fabric drivers that currently set ->aborted_task() to
NOPs are:
- loopback
- tcm_fc
- usb-gadget
- sbp-target
- vhost-scsi
For the latter five, there appears to be no additional cleanup
required before invoking TFO->release_cmd() to release the
se_cmd descriptor.
v2 changes:
- Move ->aborted_task() call into transport_cmd_finish_abort (Alex)
Cc: Alex Leung <amleung21@yahoo.com>
Cc: Mark Rustad <mark.d.rustad@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Vu Pham <vu@mellanox.com>
Cc: Chris Boot <bootc@bootc.net>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses three of long standing issues wrt to Task
Aborted Status (TAS) handling.
The first is the incorrect assumption in core_tmr_handle_tas_abort()
that TASK_ABORTED status is sent for the task referenced by TMR
ABORT_TASK, and sending TASK_ABORTED status for TMR LUN_RESET on
the same nexus the LUN_RESET was received.
The second is to ensure the lun reference count is dropped within
transport_cmd_finish_abort() by calling transport_lun_remove_cmd()
before invoking transport_cmd_check_stop_to_fabric().
The last is to fix the delayed TAS handling to allow outstanding
WRITEs to complete before sending the TASK_ABORTED status. This
includes changing transport_check_aborted_status() to avoid
processing when SCF_SEND_DELAYED_TAS has not be set, and updating
transport_send_task_abort() to drop the SCF_SENT_DELAYED_TAS
check.
Signed-off-by: Alex Leung <amleung21@yahoo.com>
Cc: Alex Leung <amleung21@yahoo.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds check for NopOUT->flag (LMB) which is a mandatory
as per RFC 3720 Section 10.18.
(Fix up context changes for v3.14-rc code - nab)
Signed-off-by: Arshad Hussain <arshad.hussain@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
User may enable T10-PI support per network portal group. any connection
established on top of it, will be required to serve protected transactions.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case an iscsi portal group will be defined as t10_pi enabled,
all connections on top of it will support protected transactions.
T10-PI support may require extra reource allocation and maintenance by
the transport layer, so we don't want to apply them on non-t10_pi network
portals. This is a hook for the iscsi target layer to signal the transport
at connection establishment that this connection will carry protected
transactions.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This is not going to be supported soon - so drop it.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Some transports (iSCSI/iSER/SRP/FC) support hardware INSERT/STRIP
capabilities while other transports like loopback/vhost-scsi need
perform this is software.
This patch allows fabrics using SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC
to signal the early LUN scan handling case where PROTECT CDB bits
are set, but no fabric buffer has been provided.
For transports which use generic new command these buffers have yet
to be allocated.
Also this way, target may support protection information
against legacy initiators (writes are inserted and reads
are stripped).
(Only set prot_pto for loopback during early special case - nab)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
No need to actually compute protection information when formatting
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
SBC-3 mandates the protection checks that must be
performed in the rdprotect/wrprotect field. Use them.
According to backstore device pi_attributes and
cdb rdprotect/wrprotect field.
(Fix incorrect se_cmd->prot_type -> TARGET_PROT_NORMAL
comparision in transport_generic_new_cmd - nab)
(Fix missing break in sbc_set_prot_op_checks - DanC + Sagi)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case protection information is involved, allocate
protection SG-list for transport.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Building target_core_alua.o triggers a GCC warning:
drivers/target/target_core_alua.c: In function ‘target_alua_state_check’:
drivers/target/target_core_alua.c:773:18: warning: ‘alua_ascq’ may be used uninitialized in this function [-Wmaybe-uninitialized]
cmd->scsi_ascq = alua_ascq;
^
This is a false positive. A little trial and error shows it is
apparently caused by core_alua_state_lba_dependent(). It must be hard
for GCC to track the branches of a switch statement, inside a
list_for_each_entry loop, inside a while loop.
But if we add a small (inline) helper function we can reorganize the
code a bit. That also allows to drop alua_ascq which, obviously, gets
rid of this warning.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When copying between device and command protection scatters
we must take into account that device scatters might be offset
and we might copy outside scatter range. Thus for each cmd prot
scatter we must take the min between cmd prot scatter, dev prot
scatter, and whats left (and loop in case we havn't copied enough
from/to cmd prot scatter).
Example (single t_prot_sg of len 2048):
kernel: sbc_dif_copy_prot: se_cmd=ffff880380aaf970, left=2048, len=2048, dev_prot_sg_offset=3072, dev_prot_sg_len=4096
kernel: isert: se_cmd=ffff880380aaf970 PI error found type 0 at sector 0x2600 expected 0x0 vs actual 0x725f, lba=2580
Instead of copying 2048 from offset 3072 (copying junk outside sg
limit 4096), we must to copy 1024 and continue to next sg until
we complete cmd prot scatter.
This issue was found using iSER T10-PI offload over rd_mcp (wasn't
discovered with fileio since file_dev prot sglists are never offset).
Changes from v1:
- Fix sbc_copy_prot copy length miss-calculation
Changes from v0:
- Removed psg->offset consideration for psg_len computation
- Removed sg->offset consideration for offset condition
- Added copied consideraiton for len computation
- Added copied offset to paddr when doing memcpy
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a couple of different hug shutdown issues
related to wait_event() + isert_conn->state. First, it changes
isert_conn->conn_wait + isert_conn->conn_wait_comp_err from
waitqueues to completions, and sets ISER_CONN_TERMINATING from
within isert_disconnect_work().
Second, it splits isert_free_conn() into isert_wait_conn() that
is called earlier in iscsit_close_connection() to ensure that
all outstanding commands have completed before continuing.
Finally, it breaks isert_cq_comp_err() into seperate TX / RX
related code, and adds logic in isert_cq_rx_comp_err() to wait
for outstanding commands to complete before setting ISER_CONN_DOWN
and calling complete(&isert_conn->conn_wait_comp_err).
Acked-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There are a handful of uses of list_empty() for cmd->i_conn_node
within iser-target code that expect to return false once a cmd
has been removed from the per connect list.
This patch changes all uses of list_del -> list_del_init in order
to ensure that list_empty() returns false as expected.
Acked-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in iscsit_get_tpg_from_np() where the
tpg->tpg_state sanity check was looking for TPG_STATE_FREE,
instead of != TPG_STATE_ACTIVE.
The latter is expected during a normal TPG shutdown once the
tpg_state goes into TPG_STATE_INACTIVE in order to reject any
new incoming login attempts.
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Because then this sg is passed to sbc_copy_prot which will
hit a protection fault in cases we have more than a single sg.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds the three missing DIF related sense codes within
transport_generic_request_failure(), which are required to ensure
that the correct ASC/ASQC is generated by the subsequent call to
transport_send_check_condition_and_sense().
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in sbc_dif_copy_prot() where the updated addr
offset did not take into account the case where the associated
scatterlist had not been incremented.
This addresses the case where incoming protection scatterlists may
contain a length smaller than PAGE_SIZE across multiple entires,
when the target protection scatterlists are always being explicitly
filled up to PAGE_SIZE before adding another entry.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Need to take into account that protection sg_list
(copy-buffer) may consist of multiple entries.
Changes from v0:
- Changed commit description
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The CMD_T_FAILED flag is set used in one place to record the result of a
trivial test, and it is only tested once, few lines later. We might as
well make the code simpler and easier to read by directly doing the test
of "success" where we want to use it.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes Status SNACK handling of BegRun=0 to allow
for all unacknowledged respones to be resent, instead of
always assuming that BegRun would be an explicit value less
than the current ExpStatSN.
Reported-by: santosh kulkarni <santosh.kulkarni@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Commit fbfe858fea ("target_core_spc: Include target device
descriptor in VPD page 83") added a new length variable, but (due to a
cut and paste mistake?) just checks scsi_name_len against 256 twice.
Fix this to check scsi_target_len for overflow too.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes core_alua_state_lba_dependent() to use do_div()
instead sector_div() to avoid the following link error on 32-bit
with CONFIG_LBDAF=n as reported by Jim:
buildlog-1391099072.txt-drivers/built-in.o: In function `target_alua_state_check':
buildlog-1391099072.txt-(.text+0x928d93): undefined reference to `__umoddi3'
buildlog-1391099072.txt:make: *** [vmlinux] Error 1 --
buildlog-1391101753.txt- CC init/version.o
buildlog-1391101753.txt- LD init/built-in.o
buildlog-1391101753.txt-drivers/built-in.o: In function `core_alua_state_lba_dependent':
buildlog-1391101753.txt-/home/jim/linux/drivers/target/target_core_alua.c:503: undefined reference to `__umoddi3'
buildlog-1391101753.txt:make: *** [vmlinux] Error 1
Reported-by: Jim Davis <jim.epost@gmail.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a >= v3.11 free-after-use regression
in core_scsi3_emulate_pro_register() that was introduced
in the following commit:
commit bc118fe4c4
Author: Andy Grover <agrover@redhat.com>
Date: Thu May 16 10:41:04 2013 -0700
target: Further refactoring of core_scsi3_emulate_pro_register()
To avoid the free-after-use, save an type value before hand, and
only call core_scsi3_put_pr_reg() with a valid *pr_reg.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: <stable@vger.kernel.org> #3.11+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- add support for SCSI Referrals (Hannes)
- add support for T10 DIF into target core (nab + mkp)
- add support for T10 DIF emulation in FILEIO + RAMDISK backends (Sagi + nab)
- add support for T10 DIF -> bio_integrity passthrough in IBLOCK backend (nab)
- prep changes to iser-target for >= v3.15 T10 DIF support (Sagi)
- add support for qla2xxx N_Port ID Virtualization - NPIV (Saurav + Quinn)
- allow percpu_ida_alloc() to receive task state bitmask (Kent)
- fix >= v3.12 iscsi-target session reset hung task regression (nab)
- fix >= v3.13 percpu_ref se_lun->lun_ref_active race (nab)
- fix a long-standing network portal creation race (Andy)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (51 commits)
target: Fix percpu_ref_put race in transport_lun_remove_cmd
target/iscsi: Fix network portal creation race
target: Report bad sector in sense data for DIF errors
iscsi-target: Convert gfp_t parameter to task state bitmask
iscsi-target: Fix connection reset hang with percpu_ida_alloc
percpu_ida: Make percpu_ida_alloc + callers accept task state bitmask
iscsi-target: Pre-allocate more tags to avoid ack starvation
qla2xxx: Configure NPIV fc_vport via tcm_qla2xxx_npiv_make_lport
qla2xxx: Enhancements to enable NPIV support for QLOGIC ISPs with TCM/LIO.
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
IB/isert: pass scatterlist instead of cmd to fast_reg_mr routine
IB/isert: Move fastreg descriptor creation to a function
IB/isert: Avoid frwr notation, user fastreg
IB/isert: seperate connection protection domains and dma MRs
tcm_loop: Enable DIF/DIX modes in SCSI host LLD
target/rd: Add DIF protection into rd_execute_rw
target/rd: Add support for protection SGL setup + release
target/rd: Refactor rd_build_device_space + rd_release_device_space
target/file: Add DIF protection support to fd_execute_rw
target/file: Add DIF protection init/format support
...
This patch fixes a percpu_ref_put race for se_lun->lun_ref in
transport_lun_remove_cmd() where ->lun_ref could end up being
put more than once per command via different target completion
and fabric release contexts.
It adds a cmpxchg() for se_cmd->lun_ref_active to ensure that
percpu_ref_put() is only ever called once per se_cmd.
This bug was manifesting itself as a LUN shutdown regression
bug in >= v3.13 code, where percpu_ref_kill() would end up
hanging indefinately due to the incorrect percpu_ref count.
(Change se_cmd->lun_ref_active from bool -> int to force at
least a 4-byte cmpxchg with MIPS ll/sc ins. - Fengguang)
Reported-by: Tommy Apel <tommyapeldk@gmail.com>
Cc: Tommy Apel <tommyapeldk@gmail.com>
Cc: <stable@vger.kernel.org> #3.13+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When creating network portals rapidly, such as when restoring a
configuration, LIO's code to reuse existing portals can return a false
negative if the thread hasn't run yet and set np_thread_state to
ISCSI_NP_THREAD_ACTIVE. This causes an error in the network stack
when attempting to bind to the same address/port.
This patch sets NP_THREAD_ACTIVE before the np is placed on g_np_list,
so even if the thread hasn't run yet, iscsit_get_np will return the
existing np.
Also, convert np_lock -> np_mutex + hold across adding new net portal
to g_np_list to prevent a race where two threads may attempt to create
the same network portal, resulting in one of them failing.
(nab: Add missing mutex_unlocks in iscsit_add_np failure paths)
(DanC: Fix incorrect spin_unlock -> spin_unlock_bh)
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: <stable@vger.kernel.org> #3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
SPC-4 states that data-integrity errors shall also report
the failed sector in CHECK_CONDITION response sense data
information field.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch propigates the use of task state bitmask now used by
percpu_ida_alloc() up the iscsi-target callchain, replacing the
use of GFP_ATOMIC for TASK_RUNNING, and GFP_KERNEL for
TASK_INTERRUPTIBLE.
Also, drop the unnecessary gfp_t parameter to isert_allocate_cmd(),
and just pass TASK_INTERRUPTIBLE into iscsit_allocate_cmd().
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a bug where connection reset would hang
indefinately once percpu_ida_alloc() was starved for tags, due
to the fact that it always assumed uninterruptible sleep mode.
So now make percpu_ida_alloc() check for signal_pending_state() for
making interruptible sleep optional, and convert iscsit_allocate_cmd()
to set TASK_INTERRUPTIBLE for GFP_KERNEL, or TASK_RUNNING for
GFP_ATOMIC.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes percpu_ida_alloc() + callers to accept task state
bitmask for prepare_to_wait() for code like target/iscsi that needs
it for interruptible sleep, that is provided in a subsequent patch.
It now expects TASK_UNINTERRUPTIBLE when the caller is able to sleep
waiting for a new tag, or TASK_RUNNING when the caller cannot sleep,
and is forced to return a negative value when no tags are available.
v2 changes:
- Include blk-mq + tcm_fc + vhost/scsi + target/iscsi changes
- Drop signal_pending_state() call
v3 changes:
- Only call prepare_to_wait() + finish_wait() when != TASK_RUNNING
(PeterZ)
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses an traditional iscsi-target fabric ack starvation
issue where iscsit_allocate_cmd() -> percpu_ida_alloc_state() ends up
hitting slow path percpu-ida code, because iscsit_ack_from_expstatsn()
is expected to free ack'ed tags after tag allocation.
This is done to take into account the tags waiting to be acknowledged
and released in iscsit_ack_from_expstatsn(), but who's number are not
directly limited by the CmdSN Window queue_depth being enforced by
the target.
So that said, this patch bumps up the pre-allocated number of
per session tags to:
(max(queue_depth, ISCSIT_MIN_TAGS) * 2) + ISCSIT_EXTRA_TAGS
for good measure to avoid the percpu_ida_alloc_state() slow path.
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch updates tcm_loop_driver_probe() to set protection
information using scsi_host_set_prot() and scsi_host_set_guard(),
which currently enabled all modes of DIF/DIX protection, minus
DIX TYPE0.
Also, update tcm_loop_submission_work() to pass struct scsi_cmnd
related protection into target_submit_cmd_map_sgls() during CDB
dispatch.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for DIF protection into rd_execute_rw() code
for WRITE/READ I/O using sbc_dif_verify_[write,read]() logic.
It also adds rd_get_prot_table() for locating protection SGLs
assoicated with the ramdisk backend device.
v2 changes:
- Make rd_execute_rw() to u32 sectors count instead of sector_t
- Drop SCF_PROT usage
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds rd_build_prot_space() + rd_release_prot_space() logic
to setup + release protection information scatterlists.
It also adds rd_init_prot() + rd_free_prot() se_subsystem_api
callbacks used by target core code for setup + release of
protection information.
v2 changes:
- Drop unused sg_table from rd_release_prot_space (Wei)
- Drop rd_release_prot_space call from rd_free_device
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch refactors rd_build_device_space() + rd_release_device_space()
into rd_allocate_sgl_table() + rd_release_device_space() so that they
may be used seperatly for setup + release of protection information
scatterlists.
Also add explicit memset of pages within rd_allocate_sgl_table() based
upon passed 'init_payload' value.
v2 changes:
- Drop unused sg_table from rd_release_device_space (Wei)
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for DIF protection into fd_execute_rw() code
for WRITE/READ I/O using sbc_dif_verify_[write,read]() logic.
It adds fd_do_prot_rw() for handling interface with FILEIO PI, and
uses a locally allocated fd_prot->prot_buf + fd_prot->prot_sg for
interacting with SBC DIF verify emulation code.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for DIF protection init/format support into
the FILEIO backend.
It involves using a seperate $FILE.protection for storing PI that is
opened via fd_init_prot() using the common pi_prot_type attribute.
The actual formatting of the protection is done via fd_format_prot()
using the common pi_prot_format attribute, that will populate the
initial PI data based upon the currently configured pi_prot_type.
Based on original FILEIO code from Sagi.
v1 changes:
- Fix sparse warnings in fd_init_format_buf (Fengguang)
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds blk_integrity passthrough support for block_device
backends using IBLOCK.
This includes iblock_alloc_bip() + setup of bio_integrity_payload
information that attaches to the leading struct bio once bio_list
is populated during fast-path iblock_execute_rw() I/O dispatch.
It also updates setup in iblock_configure_device() to detect modes
of protection + se dev->dev_attrib.pi_prot_type accordingly, along
with creating required bio_set integrity mempools.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support to target_submit_cmd_map_sgls() for
accepting 'sgl_prot' + 'sgl_prot_count' parameters for
DIF protection information.
Note the passed parameters are stored at se_cmd->t_prot_sg
and se_cmd->t_prot_nents respectively.
Also, update tcm_loop and vhost-scsi fabrics usage of
target_submit_cmd_map_sgls() to take into account the
new parameters.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for exposing DIF protection device
attributes via configfs. This includes:
pi_prot_type: Protection Type (0, 1, 3 currently support)
pi_prot_format: Protection Format Operation (FILEIO only)
Within se_dev_set_pi_prot_type() it also adds the se_subsystem_api
device callbacks to setup per device protection information.
v2 changes:
- Drop pi_guard_type + pi_prot_version related code (MKP)
- Add pi_prot_format logic (Sagi)
- Add ->free_prot callback in target_free_device
- Add hw_pi_prot_type read-only attribute
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch updates spc_modesense_control() to set the Application
Tag Owner (ATO) bit when when DIF emulation is enabled by the
backend device.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch updates sbc_emulate_readcapacity_16() to set
P_TYPE and PROT_EN bits when DIF emulation is enabled by
the backend device.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch updates spc_emulate_evpd_86() (extended INQUIRY) to
report GRD_CHK (Guard Check) and REF_CHK (Reference Check) bits
when DIF emulation is enabled by the backend device.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch updates spc_emulate_inquiry_std() to set the
PROTECT bit when DIF emulation is enabled by the backend
device.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for DIF read/write verify emulation
for TARGET_DIF_TYPE1_PROT + TARGET_DIF_TYPE3_PROT operation.
This includes sbc_dif_verify_write() + sbc_dif_verify_read()
calls accessable by backend drivers to perform DIF verify
for SGL based data and protection information.
Also included is sbc_dif_copy_prot() logic to copy protection
information to/from backend provided protection SGLs.
Based on scsi_debug.c DIF TYPE1+TYPE3 emulation.
v2 changes:
- Select CRC_T10DIF for TARGET_CORE in Kconfig (Fengguang)
- Drop IP checksum logic from sbc_dif_v1_verify (MKP)
- Fix offset on app_tag = 0xffff in sbc_dif_verify_read()
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds sbc_check_prot() for performing various DIF
related CDB sanity checks, along with setting cmd->prot_type
once sanity checks have passed.
Also, add calls in sbc_parse_cdb() for READ_[10,12,16] +
WRITE_[10,12,16] to perform DIF sanity checking.
v2 changes:
- Make sbc_check_prot defined as static (Fengguang + Wei)
- Remove unprotected READ/WRITE warning (mkp)
- Populate cmd->prot_type + friends (Sagi)
- Drop SCF_PROT usage
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for DIF related CHECK_CONDITION ASC/ASCQ
exception cases into transport_send_check_condition_and_sense().
This includes:
LOGICAL BLOCK GUARD CHECK FAILED
LOGICAL BLOCK APPLICATION TAG CHECK FAILED
LOGICAL BLOCK REFERENCE TAG CHECK FAILED
that used by DIF TYPE1 and TYPE3 failure cases.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts the temporary buffer in spc_emulate_inquiry() to
use dynamically allocated memory, instead of local stack memory.
Also bump SE_INQUIRY_BUF up to 1024 bytes to be safe when handling
multiple large SCSI name descriptors for EVPD=0x83.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When a writing to a command-provided buffer we need to ensure
that we're not writing past the end of it.
At the same time we need to continue processing as typically
the final data length (ie the required size of the buffer)
need to be returned.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Mark functions ft_tpg_alloc_fabric_acl(), ft_register_configfs() and
ft_deregister_configfs() as static in tcm_fc/tfc_conf.c because they are
not used outside this file.
This eliminates the following warnings in tcm_fc/tfc_conf.c:
drivers/target/tcm_fc/tfc_conf.c:270:21: warning: no previous prototype for ‘ft_tpg_alloc_fabric_acl’ [-Wmissing-prototypes]
drivers/target/tcm_fc/tfc_conf.c:555:5: warning: no previous prototype for ‘ft_register_configfs’ [-Wmissing-prototypes]
drivers/target/tcm_fc/tfc_conf.c:602:6: warning: no previous prototype for ‘ft_deregister_configfs’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Mark functions tcm_loop_make_naa_tpg(), tcm_loop_drop_naa_tpg(),
tcm_loop_make_scsi_hba() and tcm_loop_drop_scsi_hba() as static in
loopback/tcm_loop.c because they are not used outside this file.
This eliminates the following warning in loopback/tcm_loop.c:
drivers/target/loopback/tcm_loop.c:1231:25: warning: no previous prototype for ‘tcm_loop_make_naa_tpg’ [-Wmissing-prototypes]
drivers/target/loopback/tcm_loop.c:1276:6: warning: no previous prototype for ‘tcm_loop_drop_naa_tpg’ [-Wmissing-prototypes]
drivers/target/loopback/tcm_loop.c:1308:16: warning: no previous prototype for ‘tcm_loop_make_scsi_hba’ [-Wmissing-prototypes]
drivers/target/loopback/tcm_loop.c:1378:6: warning: no previous prototype for ‘tcm_loop_drop_scsi_hba’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Mark function iblock_get_write_cache() as static in target_core_iblock.c
because it is not used outside this file.
This eliminates the following warning in target_core_iblock.c:
drivers/target/target_core_iblock.c:766:6: warning: no previous prototype for ‘iblock_get_write_cache’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Move prototype declaration of function
spc_parse_naa_6h_vendor_specific() from target_core_xcopy.c to header
file target_core_pr.h because it is used by more than one file.
This eliminates the following warning in target_core_spc.c:
drivers/target/target_core_spc.c:138:6: warning: no previous prototype for ‘spc_parse_naa_6h_vendor_specific’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Referrals need an LBA map, which needs to be kept
consistent across all target port groups. So
instead of tying the map to the target port groups
I've implemented a single attribute containing the
entire map.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add infrastructure for referrals.
v2 changes:
- Fix unsigned long long division in core_alua_state_lba_dependent on
32-bit (Fengguang + Chen + Hannes)
- Fix compile warning in core_alua_state_lba_dependent (nab)
- Convert segment_* + sectors variables in core_alua_state_lba_dependent
to u64 (Hannes)
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJSwLfoAAoJEHm+PkMAQRiGi6QH/1U1B7lmHChDTw3jj1lfm9gA
189Si4QJlnxFWCKHvKEL+pcaVuACU+aMGI8+KyMYK4/JfuWVjjj5fr/SvyHH2/8m
LdSK8aHMhJ46uBS4WJ/l6v46qQa5e2vn8RKSBAyKm/h4vpt+hd6zJdoFrFai4th7
k/TAwOAEHI5uzexUChwLlUBRTvbq4U8QUvDu+DeifC8cT63CGaaJ4qVzjOZrx1an
eP6UXZrKDASZs7RU950i7xnFVDQu4PsjlZi25udsbeiKcZJgPqGgXz5ULf8ZH8RQ
YCi1JOnTJRGGjyIOyLj7pyB01h7XiSM2+eMQ0S7g54F2s7gCJ58c2UwQX45vRWU=
=/4/R
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc6' into for-3.14/core
Needed to bring blk-mq uptodate, since changes have been going in
since for-3.14/core was established.
Fixup merge issues related to the immutable biovec changes.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Conflicts:
block/blk-flush.c
fs/btrfs/check-integrity.c
fs/btrfs/extent_io.c
fs/btrfs/scrub.c
fs/logfs/dev_bdev.c
lun->lun_ref is also initialized in core_tpg_post_addlun, so it doesn't
need to be done in core_tpg_setup_virtual_lun0.
(nab: Drop left-over percpu_ref_cancel_init in failure path)
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch allows FILEIO to update hw_max_sectors based on the current
max_bytes_per_io. This is required because vfs_[writev,readv]() can accept
a maximum of 2048 iovecs per call, so the enforced hw_max_sectors really
needs to be calculated based on block_size.
This addresses a >= v3.5 bug where block_size=512 was rejecting > 1M
sized I/O requests, because FD_MAX_SECTORS was hardcoded to 2048 for
the block_size=4096 case.
(v2: Use max_bytes_per_io instead of ->update_hw_max_sectors)
Reported-by: Henrik Goldman <hg@x-formation.com>
Cc: <stable@vger.kernel.org> #3.5+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When shutting down a target there is a race condition between
iscsit_del_np() and __iscsi_target_login_thread().
The latter sets the thread pointer to NULL, and the former
tries to issue kthread_stop() on that pointer without any
synchronization.
This patch moves the np->np_thread NULL assignment into
iscsit_del_np(), after kthread_stop() has completed. It also
removes the signal_pending() + np_state check, and only
exits when kthread_should_stop() is true.
Reported-by: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We should be including a descriptor referring to the target device
to allow identification of different TCM instances.
(nab: Bump SE_INQUIRY_BUF to 1024 bytes to handle 2x 256 byte SCSI names)
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
scsi_name_len in spc_emulate_evpd_83 is calculated twice, with
the results of the first calculation discarded. So remove it.
And check for the maximum allowed length, too.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use a workqueue for processing ALUA state transitions; this allows
us to process implicit delay properly.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
During state transition we should be storing both the original
and the pending state.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We should only allocate ALUA metadata if we're actually going
to write them.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
As we now can modify the list of supported states we need to
validate the requested ALUA state when doing a state transition.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
"pre" is really an allocation function. The only time it isn't called is
for virtual_lun0, which is statically allocated. Renaming that to "alloc"
lets the other function not need to be "post", and just be called
core_tpg_add_lun.
(nab: fix minor applying fuzz in core_tpg_setup_virtual_lun0)
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It's clearer to refer to pointers to the struct se_lun as "lun" and the
actual number itself as "unpacked_lun".
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Allocating an array of pointers, not the objects themselves. These two
sites now match all the other sites.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
See target_stat_setup_port_default_groups, we need a 4 element array.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes special case handling for ISCSI_OP_SCSI_CMD
where an initiator sends a zero length Expected Data Transfer
Length (EDTL), but still sets the WRITE and/or READ flag bits
when no payload transfer is requested.
Many, many moons ago two special cases where added for an ancient
version of ESX that has long since been fixed, so instead of adding
a new special case for the reported bug with a Broadcom 57800 NIC,
go ahead and always strip off the incorrect WRITE + READ flag bits.
Also, avoid sending a reject here, as RFC-3720 does mandate this
case be handled without protocol error.
Reported-by: Witold Bazakbal <865perl@wp.pl>
Tested-by: Witold Bazakbal <865perl@wp.pl>
Cc: <stable@vger.kernel.org> #3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Commit 04f3b31bff ("iscsi-target: Convert iscsi_session statistics to
atomic_long_t") removed the updating of these fields in iscsi (the only
fabric driver that ever touched these counters), and the core has no way
to report or otherwise use the values. Remove the last remnants of
these counters.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The iSCSI CHAP auth parameters are already copied with respect for
the destination buffer size. Return -EINVAL instead of silently
truncating the input.
Signed-off-by: Eric Seppanen <eric@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"Things have been quiet this round with mostly bugfixes, percpu
conversions, and other minor iscsi-target conformance testing changes.
The highlights include:
- Add demo_mode_discovery attribute for iscsi-target (Thomas)
- Convert tcm_fc(FCoE) to use percpu-ida pre-allocation
- Add send completion interrupt coalescing for ib_isert
- Convert target-core to use percpu-refcounting for se_lun
- Fix mutex_trylock usage bug in iscsit_increment_maxcmdsn
- tcm_loop updates (Hannes)
- target-core ALUA cleanups + prep for v3.14 SCSI Referrals support (Hannes)
v3.14 is currently shaping to be a busy development cycle in target
land, with initial support for T10 Referrals and T10 DIF currently on
the roadmap"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (40 commits)
iscsi-target: chap auth shouldn't match username with trailing garbage
iscsi-target: fix extract_param to handle buffer length corner case
iscsi-target: Expose default_erl as TPG attribute
target_core_configfs: split up ALUA supported states
target_core_alua: Make supported states configurable
target_core_alua: Store supported ALUA states
target_core_alua: Rename ALUA_ACCESS_STATE_OPTIMIZED
target_core_alua: spellcheck
target core: rename (ex,im)plict -> (ex,im)plicit
percpu-refcount: Add percpu-refcount.o to obj-y
iscsi-target: Do not reject non-immediate CmdSNs exceeding MaxCmdSN
iscsi-target: Convert iscsi_session statistics to atomic_long_t
target: Convert se_device statistics to atomic_long_t
target: Fix delayed Task Aborted Status (TAS) handling bug
iscsi-target: Reject unsupported multi PDU text command sequence
ib_isert: Avoid duplicate iscsit_increment_maxcmdsn call
iscsi-target: Fix mutex_trylock usage in iscsit_increment_maxcmdsn
target: Core does not need blkdev.h
target: Pass through I/O topology for block backstores
iser-target: Avoid using FRMR for single dma entry requests
...
In iSCSI negotiations with initiator CHAP enabled, usernames with
trailing garbage are permitted, because the string comparison only
checks the strlen of the configured username.
e.g. "usernameXXXXX" will be permitted to match "username".
Just check one more byte so the trailing null char is also matched.
Signed-off-by: Eric Seppanen <eric@purestorage.com>
Cc: <stable@vger.kernel.org> #3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
extract_param() is called with max_length set to the total size of the
output buffer. It's not safe to allow a parameter length equal to the
buffer size as the terminating null would be written one byte past the
end of the output buffer.
Signed-off-by: Eric Seppanen <eric@purestorage.com>
Cc: <stable@vger.kernel.org> #3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch exposes default_erl as a TPG attribute so that it may be
set TPG wide in demo-mode, but still allow the existing NodeACL
attribute to be overridden on a per initiator basis.
Reported-by: Arshad Hussain <arshad.hussain@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Split up the various ALUA states into individual attributes to
make parsing easier and adhere to the one value per attribute
sysfs principle.
(nab: Convert strict_strtoul -> kstrtoul usage)
Signed-off-by: Hannes Reinecke <hare@suse.de>
The supported ALUA states might be different for individual
devices, so store it in a separate field.
(nab: Remove unnecessary line continuation)
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Rename ALUA_ACCESS_STATE_OPTMIZED to
ALUA_ACCESS_STATE_OPTIMIZED.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes iscsit_sequence_cmd() logic to no longer reject
non-immediate CmdSNs that exceed MaxCmdSN with a protocol error,
but instead silently ignore them.
This is done to correctly follow RFC-3720 Section 3.2.2.1:
For non-immediate commands, the CmdSN field can take any
value from ExpCmdSN to MaxCmdSN inclusive. The target MUST silently
ignore any non-immediate command outside of this range or non-
immediate duplicates within the range.
Reported-by: Santosh Kulkarni <santosh.kulkarni@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts a handful of iscsi_session statistics to type
atomic_long_t, instead of using iscsi_session->session_stats_lock
when incrementing these values.
More importantly, go ahead and drop the spinlock usage within
iscsit_setup_scsi_cmd(), iscsit_check_dataout_hdr(),
iscsit_send_datain(), and iscsit_build_rsp_pdu() fast-path code.
(Squash in Roland's target: Remove write-only stats fields and lock
from struct se_node_acl)
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts the handful of se_device statistics to type
atomic_long_t, instead of using se_device->stats_lock when
incrementing these values.
More importantly, go ahead and drop the spinlock usage within
transport_lookup_cmd_lun() fast-path code.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in delayed Task Aborted Status (TAS) handling,
where transport_send_task_abort() was not returning for the case
when the se_tfo->write_pending() callback indicated that last fabric
specific WRITE PDU had not yet been received.
It also adds an explicit cmd->scsi_status = SAM_STAT_TASK_ABORTED
assignment within transport_check_aborted_status() to avoid the case
where se_tfo->queue_status() is called when the SAM_STAT_TASK_ABORTED
assignment + ->queue_status() in transport_send_task_abort() does not
occur once SCF_SENT_DELAYED_TAS has been set.
Cc: <stable@vger.kernel.org> #3.2+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a check to reject text commands with F_BIT=0 ||
C_BIT=1, as multi PDU text command sequences are currently
unsupported.
This avoids the case where a text command received with F_BIT=0,
was generating a text response with F_BIT=1 which is a protocol
error according to RFC-3720 Section 10.11.1.
Reported-by: Arshad Hussain <arshad.hussain@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Nicholas Bellinger