The second word of key->payload does not get initialised in key_alloc(), but
the big_key type is relying on it having been cleared. The problem comes when
big_key fails to instantiate a large key and doesn't then set the payload. The
big_key_destroy() op is called from the garbage collector and this assumes that
the dentry pointer stored in the second word will be NULL if instantiation did
not complete.
Therefore just pre-clear the entire struct key on allocation rather than trying
to be clever and only initialising to 0 only those bits that aren't otherwise
initialised.
The lack of initialisation can lead to a bug report like the following if
big_key failed to initialise its file:
general protection fault: 0000 [#1] SMP
Modules linked in: ...
CPU: 0 PID: 51 Comm: kworker/0:1 Not tainted 3.10.0-53.el7.x86_64 #1
Hardware name: Dell Inc. PowerEdge 1955/0HC513, BIOS 1.4.4 12/09/2008
Workqueue: events key_garbage_collector
task: ffff8801294f5680 ti: ffff8801296e2000 task.ti: ffff8801296e2000
RIP: 0010:[<ffffffff811b4a51>] dput+0x21/0x2d0
...
Call Trace:
[<ffffffff811a7b06>] path_put+0x16/0x30
[<ffffffff81235604>] big_key_destroy+0x44/0x60
[<ffffffff8122dc4b>] key_gc_unused_keys.constprop.2+0x5b/0xe0
[<ffffffff8122df2f>] key_garbage_collector+0x1df/0x3c0
[<ffffffff8107759b>] process_one_work+0x17b/0x460
[<ffffffff8107834b>] worker_thread+0x11b/0x400
[<ffffffff81078230>] ? rescuer_thread+0x3e0/0x3e0
[<ffffffff8107eb00>] kthread+0xc0/0xd0
[<ffffffff8107ea40>] ? kthread_create_on_node+0x110/0x110
[<ffffffff815c4bec>] ret_from_fork+0x7c/0xb0
[<ffffffff8107ea40>] ? kthread_create_on_node+0x110/0x110
Reported-by: Patrik Kis <pkis@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Stephen Gallagher <sgallagh@redhat.com>
Add KEY_FLAG_TRUSTED to indicate that a key either comes from a trusted source
or had a cryptographic signature chain that led back to a trusted key the
kernel already possessed.
Add KEY_FLAGS_TRUSTED_ONLY to indicate that a keyring will only accept links to
keys marked with KEY_FLAGS_TRUSTED.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Expand the capacity of a keyring to be able to hold a lot more keys by using
the previously added associative array implementation. Currently the maximum
capacity is:
(PAGE_SIZE - sizeof(header)) / sizeof(struct key *)
which, on a 64-bit system, is a little more 500. However, since this is being
used for the NFS uid mapper, we need more than that. The new implementation
gives us effectively unlimited capacity.
With some alterations, the keyutils testsuite runs successfully to completion
after this patch is applied. The alterations are because (a) keyrings that
are simply added to no longer appear ordered and (b) some of the errors have
changed a bit.
Signed-off-by: David Howells <dhowells@redhat.com>
Drop the permissions argument from __keyring_search_one() as the only caller
passes 0 here - which causes all checks to be skipped.
Signed-off-by: David Howells <dhowells@redhat.com>
Define a __key_get() wrapper to use rather than atomic_inc() on the key usage
count as this makes it easier to hook in refcount error debugging.
Signed-off-by: David Howells <dhowells@redhat.com>
Consolidate the concept of an 'index key' for accessing keys. The index key
is the search term needed to find a key directly - basically the key type and
the key description. We can add to that the description length.
This will be useful when turning a keyring into an associative array rather
than just a pointer block.
Signed-off-by: David Howells <dhowells@redhat.com>
Pull security subsystem updates from James Morris:
"A quiet cycle for the security subsystem with just a few maintenance
updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
Smack: create a sysfs mount point for smackfs
Smack: use select not depends in Kconfig
Yama: remove locking from delete path
Yama: add RCU to drop read locking
drivers/char/tpm: remove tasklet and cleanup
KEYS: Use keyring_alloc() to create special keyrings
KEYS: Reduce initial permissions on keys
KEYS: Make the session and process keyrings per-thread
seccomp: Make syscall skipping and nr changes more consistent
key: Fix resource leak
keys: Fix unreachable code
KEYS: Add payload preparsing opportunity prior to key instantiate or update
Pull module signing support from Rusty Russell:
"module signing is the highlight, but it's an all-over David Howells frenzy..."
Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG.
* 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits)
X.509: Fix indefinite length element skip error handling
X.509: Convert some printk calls to pr_devel
asymmetric keys: fix printk format warning
MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking
MODSIGN: Make mrproper should remove generated files.
MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs
MODSIGN: Use the same digest for the autogen key sig as for the module sig
MODSIGN: Sign modules during the build process
MODSIGN: Provide a script for generating a key ID from an X.509 cert
MODSIGN: Implement module signature checking
MODSIGN: Provide module signing public keys to the kernel
MODSIGN: Automatically generate module signing keys if missing
MODSIGN: Provide Kconfig options
MODSIGN: Provide gitignore and make clean rules for extra files
MODSIGN: Add FIPS policy
module: signature checking hook
X.509: Add a crypto key parser for binary (DER) X.509 certificates
MPILIB: Provide a function to read raw data into an MPI
X.509: Add an ASN.1 decoder
X.509: Add simple ASN.1 grammar compiler
...
Give the key type the opportunity to preparse the payload prior to the
instantiation and update routines being called. This is done with the
provision of two new key type operations:
int (*preparse)(struct key_preparsed_payload *prep);
void (*free_preparse)(struct key_preparsed_payload *prep);
If the first operation is present, then it is called before key creation (in
the add/update case) or before the key semaphore is taken (in the update and
instantiate cases). The second operation is called to clean up if the first
was called.
preparse() is given the opportunity to fill in the following structure:
struct key_preparsed_payload {
char *description;
void *type_data[2];
void *payload;
const void *data;
size_t datalen;
size_t quotalen;
};
Before the preparser is called, the first three fields will have been cleared,
the payload pointer and size will be stored in data and datalen and the default
quota size from the key_type struct will be stored into quotalen.
The preparser may parse the payload in any way it likes and may store data in
the type_data[] and payload fields for use by the instantiate() and update()
ops.
The preparser may also propose a description for the key by attaching it as a
string to the description field. This can be used by passing a NULL or ""
description to the add_key() system call or the key_create_or_update()
function. This cannot work with request_key() as that required the description
to tell the upcall about the key to be created.
This, for example permits keys that store PGP public keys to generate their own
name from the user ID and public key fingerprint in the key.
The instantiate() and update() operations are then modified to look like this:
int (*instantiate)(struct key *key, struct key_preparsed_payload *prep);
int (*update)(struct key *key, struct key_preparsed_payload *prep);
and the new payload data is passed in *prep, whether or not it was preparsed.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reduce the initial permissions on new keys to grant the possessor everything,
view permission only to the user (so the keys can be seen in /proc/keys) and
nothing else.
This gives the creator a chance to adjust the permissions mask before other
processes can access the new key or create a link to it.
To aid with this, keyring_alloc() now takes a permission argument rather than
setting the permissions itself.
The following permissions are now set:
(1) The user and user-session keyrings grant the user that owns them full
permissions and grant a possessor everything bar SETATTR.
(2) The process and thread keyrings grant the possessor full permissions but
only grant the user VIEW. This permits the user to see them in
/proc/keys, but not to do anything with them.
(3) Anonymous session keyrings grant the possessor full permissions, but only
grant the user VIEW and READ. This means that the user can see them in
/proc/keys and can list them, but nothing else. Possibly READ shouldn't
be provided either.
(4) Named session keyrings grant everything an anonymous session keyring does,
plus they grant the user LINK permission. The whole point of named
session keyrings is that others can also subscribe to them. Possibly this
should be a separate permission to LINK.
(5) The temporary session keyring created by call_sbin_request_key() gets the
same permissions as an anonymous session keyring.
(6) Keys created by add_key() get VIEW, SEARCH, LINK and SETATTR for the
possessor, plus READ and/or WRITE if the key type supports them. The used
only gets VIEW now.
(7) Keys created by request_key() now get the same as those created by
add_key().
Reported-by: Lennart Poettering <lennart@poettering.net>
Reported-by: Stef Walter <stefw@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Pull user namespace changes from Eric Biederman:
"This is a mostly modest set of changes to enable basic user namespace
support. This allows the code to code to compile with user namespaces
enabled and removes the assumption there is only the initial user
namespace. Everything is converted except for the most complex of the
filesystems: autofs4, 9p, afs, ceph, cifs, coda, fuse, gfs2, ncpfs,
nfs, ocfs2 and xfs as those patches need a bit more review.
The strategy is to push kuid_t and kgid_t values are far down into
subsystems and filesystems as reasonable. Leaving the make_kuid and
from_kuid operations to happen at the edge of userspace, as the values
come off the disk, and as the values come in from the network.
Letting compile type incompatible compile errors (present when user
namespaces are enabled) guide me to find the issues.
The most tricky areas have been the places where we had an implicit
union of uid and gid values and were storing them in an unsigned int.
Those places were converted into explicit unions. I made certain to
handle those places with simple trivial patches.
Out of that work I discovered we have generic interfaces for storing
quota by projid. I had never heard of the project identifiers before.
Adding full user namespace support for project identifiers accounts
for most of the code size growth in my git tree.
Ultimately there will be work to relax privlige checks from
"capable(FOO)" to "ns_capable(user_ns, FOO)" where it is safe allowing
root in a user names to do those things that today we only forbid to
non-root users because it will confuse suid root applications.
While I was pushing kuid_t and kgid_t changes deep into the audit code
I made a few other cleanups. I capitalized on the fact we process
netlink messages in the context of the message sender. I removed
usage of NETLINK_CRED, and started directly using current->tty.
Some of these patches have also made it into maintainer trees, with no
problems from identical code from different trees showing up in
linux-next.
After reading through all of this code I feel like I might be able to
win a game of kernel trivial pursuit."
Fix up some fairly trivial conflicts in netfilter uid/git logging code.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (107 commits)
userns: Convert the ufs filesystem to use kuid/kgid where appropriate
userns: Convert the udf filesystem to use kuid/kgid where appropriate
userns: Convert ubifs to use kuid/kgid
userns: Convert squashfs to use kuid/kgid where appropriate
userns: Convert reiserfs to use kuid and kgid where appropriate
userns: Convert jfs to use kuid/kgid where appropriate
userns: Convert jffs2 to use kuid and kgid where appropriate
userns: Convert hpfs to use kuid and kgid where appropriate
userns: Convert btrfs to use kuid/kgid where appropriate
userns: Convert bfs to use kuid/kgid where appropriate
userns: Convert affs to use kuid/kgid wherwe appropriate
userns: On alpha modify linux_to_osf_stat to use convert from kuids and kgids
userns: On ia64 deal with current_uid and current_gid being kuid and kgid
userns: On ppc convert current_uid from a kuid before printing.
userns: Convert s390 getting uid and gid system calls to use kuid and kgid
userns: Convert s390 hypfs to use kuid and kgid where appropriate
userns: Convert binder ipc to use kuids
userns: Teach security_path_chown to take kuids and kgids
userns: Add user namespace support to IMA
userns: Convert EVM to deal with kuids and kgids in it's hmac computation
...
- Replace key_user ->user_ns equality checks with kuid_has_mapping checks.
- Use from_kuid to generate key descriptions
- Use kuid_t and kgid_t and the associated helpers instead of uid_t and gid_t
- Avoid potential problems with file descriptor passing by displaying
keys in the user namespace of the opener of key status proc files.
Cc: linux-security-module@vger.kernel.org
Cc: keyrings@linux-nfs.org
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Give the key type the opportunity to preparse the payload prior to the
instantiation and update routines being called. This is done with the
provision of two new key type operations:
int (*preparse)(struct key_preparsed_payload *prep);
void (*free_preparse)(struct key_preparsed_payload *prep);
If the first operation is present, then it is called before key creation (in
the add/update case) or before the key semaphore is taken (in the update and
instantiate cases). The second operation is called to clean up if the first
was called.
preparse() is given the opportunity to fill in the following structure:
struct key_preparsed_payload {
char *description;
void *type_data[2];
void *payload;
const void *data;
size_t datalen;
size_t quotalen;
};
Before the preparser is called, the first three fields will have been cleared,
the payload pointer and size will be stored in data and datalen and the default
quota size from the key_type struct will be stored into quotalen.
The preparser may parse the payload in any way it likes and may store data in
the type_data[] and payload fields for use by the instantiate() and update()
ops.
The preparser may also propose a description for the key by attaching it as a
string to the description field. This can be used by passing a NULL or ""
description to the add_key() system call or the key_create_or_update()
function. This cannot work with request_key() as that required the description
to tell the upcall about the key to be created.
This, for example permits keys that store PGP public keys to generate their own
name from the user ID and public key fingerprint in the key.
The instantiate() and update() operations are then modified to look like this:
int (*instantiate)(struct key *key, struct key_preparsed_payload *prep);
int (*update)(struct key *key, struct key_preparsed_payload *prep);
and the new payload data is passed in *prep, whether or not it was preparsed.
Signed-off-by: David Howells <dhowells@redhat.com>
system_nrt[_freezable]_wq are now spurious. Mark them deprecated and
convert all users to system[_freezable]_wq.
If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant, so there's no reason to use system_nrt[_freezable]_wq.
Please use system[_freezable]_wq instead.
This patch doesn't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-By: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: David Howells <dhowells@redhat.com>
Pull user namespace enhancements from Eric Biederman:
"This is a course correction for the user namespace, so that we can
reach an inexpensive, maintainable, and reasonably complete
implementation.
Highlights:
- Config guards make it impossible to enable the user namespace and
code that has not been converted to be user namespace safe.
- Use of the new kuid_t type ensures the if you somehow get past the
config guards the kernel will encounter type errors if you enable
user namespaces and attempt to compile in code whose permission
checks have not been updated to be user namespace safe.
- All uids from child user namespaces are mapped into the initial
user namespace before they are processed. Removing the need to add
an additional check to see if the user namespace of the compared
uids remains the same.
- With the user namespaces compiled out the performance is as good or
better than it is today.
- For most operations absolutely nothing changes performance or
operationally with the user namespace enabled.
- The worst case performance I could come up with was timing 1
billion cache cold stat operations with the user namespace code
enabled. This went from 156s to 164s on my laptop (or 156ns to
164ns per stat operation).
- (uid_t)-1 and (gid_t)-1 are reserved as an internal error value.
Most uid/gid setting system calls treat these value specially
anyway so attempting to use -1 as a uid would likely cause
entertaining failures in userspace.
- If setuid is called with a uid that can not be mapped setuid fails.
I have looked at sendmail, login, ssh and every other program I
could think of that would call setuid and they all check for and
handle the case where setuid fails.
- If stat or a similar system call is called from a context in which
we can not map a uid we lie and return overflowuid. The LFS
experience suggests not lying and returning an error code might be
better, but the historical precedent with uids is different and I
can not think of anything that would break by lying about a uid we
can't map.
- Capabilities are localized to the current user namespace making it
safe to give the initial user in a user namespace all capabilities.
My git tree covers all of the modifications needed to convert the core
kernel and enough changes to make a system bootable to runlevel 1."
Fix up trivial conflicts due to nearby independent changes in fs/stat.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (46 commits)
userns: Silence silly gcc warning.
cred: use correct cred accessor with regards to rcu read lock
userns: Convert the move_pages, and migrate_pages permission checks to use uid_eq
userns: Convert cgroup permission checks to use uid_eq
userns: Convert tmpfs to use kuid and kgid where appropriate
userns: Convert sysfs to use kgid/kuid where appropriate
userns: Convert sysctl permission checks to use kuid and kgids.
userns: Convert proc to use kuid/kgid where appropriate
userns: Convert ext4 to user kuid/kgid where appropriate
userns: Convert ext3 to use kuid/kgid where appropriate
userns: Convert ext2 to use kuid/kgid where appropriate.
userns: Convert devpts to use kuid/kgid where appropriate
userns: Convert binary formats to use kuid/kgid where appropriate
userns: Add negative depends on entries to avoid building code that is userns unsafe
userns: signal remove unnecessary map_cred_ns
userns: Teach inode_capable to understand inodes whose uids map to other namespaces.
userns: Fail exec for suid and sgid binaries with ids outside our user namespace.
userns: Convert stat to return values mapped from kuids and kgids
userns: Convert user specfied uids and gids in chown into kuids and kgid
userns: Use uid_eq gid_eq helpers when comparing kuids and kgids in the vfs
...
Add support for invalidating a key - which renders it immediately invisible to
further searches and causes the garbage collector to immediately wake up,
remove it from keyrings and then destroy it when it's no longer referenced.
It's better not to do this with keyctl_revoke() as that marks the key to start
returning -EKEYREVOKED to searches when what is actually desired is to have the
key refetched.
To invalidate a key the caller must be granted SEARCH permission by the key.
This may be too strict. It may be better to also permit invalidation if the
caller has any of READ, WRITE or SETATTR permission.
The primary use for this is to evict keys that are cached in special keyrings,
such as the DNS resolver or an ID mapper.
Signed-off-by: David Howells <dhowells@redhat.com>
Announce the (un)registration of a key type in the core key code rather than
in the callers.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Mimi Zohar <zohar@us.ibm.com>
Optimize performance and prepare for the removal of the user_ns reference
from user_struct. Remove the slow long walk through cred->user->user_ns and
instead go straight to cred->user_ns.
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
The keyctl_set_timeout function isn't exported to other parts of the
kernel, but I want to use it for the NFS idmapper. I already have the
key, but I wanted a generic way to set the timeout.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
For CIFS, we want to be able to store NTLM credentials (aka username
and password) in the keyring. We do not, however want to allow users
to fetch those keys back out of the keyring since that would be a
security risk.
Unfortunately, due to the nuances of key permission bits, it's not
possible to do this. We need to grant search permissions so the kernel
can find these keys, but that also implies permissions to read the
payload.
Resolve this by adding a new key_type. This key type is essentially
the same as key_type_user, but does not define a .read op. This
prevents the payload from ever being visible from userspace. This
key type also vets the description to ensure that it's "qualified"
by checking to ensure that it has a ':' in it that is preceded by
other characters.
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Give keys their own lockdep class to differentiate them from each other in case
a key of one type has to refer to a key of another type.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
unregister_key_type() has code to mark a key as dead and make it unavailable in
one loop and then destroy all those unavailable key payloads in the next loop.
However, the loop to mark keys dead renders the key undetectable to the second
loop by changing the key type pointer also.
Fix this by the following means:
(1) The key code has two garbage collectors: one deletes unreferenced keys and
the other alters keyrings to delete links to old dead, revoked and expired
keys. They can end up holding each other up as both want to scan the key
serial tree under spinlock. Combine these into a single routine.
(2) Move the dead key marking, dead link removal and dead key removal into the
garbage collector as a three phase process running over the three cycles
of the normal garbage collection procedure. This is tracked by the
KEY_GC_REAPING_DEAD_1, _2 and _3 state flags.
unregister_key_type() then just unlinks the key type from the list, wakes
up the garbage collector and waits for the third phase to complete.
(3) Downgrade the key types sem in unregister_key_type() once it has deleted
the key type from the list so that it doesn't block the keyctl() syscall.
(4) Dead keys that cannot be simply removed in the third phase have their
payloads destroyed with the key's semaphore write-locked to prevent
interference by the keyctl() syscall. There should be no in-kernel users
of dead keys of that type by the point of unregistration, though keyctl()
may be holding a reference.
(5) Only perform timer recalculation in the GC if the timer actually expired.
If it didn't, we'll get another cycle when it goes off - and if the key
that actually triggered it has been removed, it's not a problem.
(6) Only garbage collect link if the timer expired or if we're doing dead key
clean up phase 2.
(7) As only key_garbage_collector() is permitted to use rb_erase() on the key
serial tree, it doesn't need to revalidate its cursor after dropping the
spinlock as the node the cursor points to must still exist in the tree.
(8) Drop the spinlock in the GC if there is contention on it or if we need to
reschedule. After dealing with that, get the spinlock again and resume
scanning.
This has been tested in the following ways:
(1) Run the keyutils testsuite against it.
(2) Using the AF_RXRPC and RxKAD modules to test keytype removal:
Load the rxrpc_s key type:
# insmod /tmp/af-rxrpc.ko
# insmod /tmp/rxkad.ko
Create a key (http://people.redhat.com/~dhowells/rxrpc/listen.c):
# /tmp/listen &
[1] 8173
Find the key:
# grep rxrpc_s /proc/keys
091086e1 I--Q-- 1 perm 39390000 0 0 rxrpc_s 52:2
Link it to a session keyring, preferably one with a higher serial number:
# keyctl link 0x20e36251 @s
Kill the process (the key should remain as it's linked to another place):
# fg
/tmp/listen
^C
Remove the key type:
rmmod rxkad
rmmod af-rxrpc
This can be made a more effective test by altering the following part of
the patch:
if (unlikely(gc_state & KEY_GC_REAPING_DEAD_2)) {
/* Make sure everyone revalidates their keys if we marked a
* bunch as being dead and make sure all keyring ex-payloads
* are destroyed.
*/
kdebug("dead sync");
synchronize_rcu();
To call synchronize_rcu() in GC phase 1 instead. That causes that the
keyring's old payload content to hang around longer until it's RCU
destroyed - which usually happens after GC phase 3 is complete. This
allows the destroy_dead_key branch to be tested.
Reported-by: Benjamin Coddington <bcodding@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Make the key reaper non-reentrant by sticking it on the appropriate system work
queue when we queue it. This will allow it to have global state and drop
locks. It should probably be non-reentrant already as it may spend a long time
holding the key serial spinlock, and so multiple entrants can spend long
periods of time just sitting there spinning, waiting to get the lock.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Move the unreferenced key reaper function to the keys garbage collector file
as that's a more appropriate place with the dead key link reaper.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Add a new keyctl op to reject a key with a specified error code. This works
much the same as negating a key, and so keyctl_negate_key() is made a special
case of keyctl_reject_key(). The difference is that keyctl_negate_key()
selects ENOKEY as the error to be reported.
Typically the key would be rejected with EKEYEXPIRED, EKEYREVOKED or
EKEYREJECTED, but this is not mandatory.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Add a key type operation to permit the key type to vet the description of a new
key that key_alloc() is about to allocate. The operation may reject the
description if it wishes with an error of its choosing. If it does this, the
key will not be allocated.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Fix __key_link_end()'s attempt to fix up the quota if an error occurs.
There are two erroneous cases: Firstly, we always decrease the quota if
the preallocated replacement keyring needs cleaning up, irrespective of
whether or not we should (we may have replaced a pointer rather than
adding another pointer).
Secondly, we never clean up the quota if we added a pointer without the
keyring storage being extended (we allocate multiple pointers at a time,
even if we're not going to use them all immediately).
We handle this by setting the bottom bit of the preallocation pointer in
__key_link_begin() to indicate that the quota needs fixing up, which is
then passed to __key_link() (which clears the whole thing) and
__key_link_end().
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up comments in the key management code. No functional changes.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do a bit of a style clean up in the key management code. No functional
changes.
Done using:
perl -p -i -e 's!^/[*]*/\n!!' security/keys/*.c
perl -p -i -e 's!} /[*] end [a-z0-9_]*[(][)] [*]/\n!}\n!' security/keys/*.c
sed -i -s -e ": next" -e N -e 's/^\n[}]$/}/' -e t -e P -e 's/^.*\n//' -e "b next" security/keys/*.c
To remove /*****/ lines, remove comments on the closing brace of a
function to name the function and remove blank lines before the closing
brace of a function.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do preallocation for __key_link() so that the various callers in request_key.c
can deal with any errors from this source before attempting to construct a key.
This allows them to assume that the actual linkage step is guaranteed to be
successful.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Fix a number of problems with the new key garbage collector:
(1) A rogue semicolon in keyring_gc() was causing the initial count of dead
keys to be miscalculated.
(2) A missing return in keyring_gc() meant that under certain circumstances,
the keyring semaphore would be unlocked twice.
(3) The key serial tree iterator (key_garbage_collector()) part of the garbage
collector has been modified to:
(a) Complete each scan of the keyrings before setting the new timer.
(b) Only set the new timer for keys that have yet to expire. This means
that the new timer is now calculated correctly, and the gc doesn't
get into a loop continually scanning for keys that have expired, and
preventing other things from happening, like RCU cleaning up the old
keyring contents.
(c) Perform an extra scan if any keys were garbage collected in this one
as a key might become garbage during a scan, and (b) could mean we
don't set the timer again.
(4) Made key_schedule_gc() take the time at which to do a collection run,
rather than the time at which the key expires. This means the collection
of dead keys (key type unregistered) can happen immediately.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Add garbage collection for dead, revoked and expired keys. This involved
erasing all links to such keys from keyrings that point to them. At that
point, the key will be deleted in the normal manner.
Keyrings from which garbage collection occurs are shrunk and their quota
consumption reduced as appropriate.
Dead keys (for which the key type has been removed) will be garbage collected
immediately.
Revoked and expired keys will hang around for a number of seconds, as set in
/proc/sys/kernel/keys/gc_delay before being automatically removed. The default
is 5 minutes.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Set the KEY_FLAG_DEAD flag on keys for which the type has been removed. This
causes the key_permission() function to return EKEYREVOKED in response to
various commands. It does not, however, prevent unlinking or clearing of
keyrings from detaching the key.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Allow keys for which the key type has been removed to be unlinked. Currently
dead-type keys can only be disposed of by completely clearing the keyrings
that point to them.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
per-uid keys were looked by uid only. Use the user namespace
to distinguish the same uid in different namespaces.
This does not address key_permission. So a task can for instance
try to join a keyring owned by the same uid in another namespace.
That will be handled by a separate patch.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Inaugurate copy-on-write credentials management. This uses RCU to manage the
credentials pointer in the task_struct with respect to accesses by other tasks.
A process may only modify its own credentials, and so does not need locking to
access or modify its own credentials.
A mutex (cred_replace_mutex) is added to the task_struct to control the effect
of PTRACE_ATTACHED on credential calculations, particularly with respect to
execve().
With this patch, the contents of an active credentials struct may not be
changed directly; rather a new set of credentials must be prepared, modified
and committed using something like the following sequence of events:
struct cred *new = prepare_creds();
int ret = blah(new);
if (ret < 0) {
abort_creds(new);
return ret;
}
return commit_creds(new);
There are some exceptions to this rule: the keyrings pointed to by the active
credentials may be instantiated - keyrings violate the COW rule as managing
COW keyrings is tricky, given that it is possible for a task to directly alter
the keys in a keyring in use by another task.
To help enforce this, various pointers to sets of credentials, such as those in
the task_struct, are declared const. The purpose of this is compile-time
discouragement of altering credentials through those pointers. Once a set of
credentials has been made public through one of these pointers, it may not be
modified, except under special circumstances:
(1) Its reference count may incremented and decremented.
(2) The keyrings to which it points may be modified, but not replaced.
The only safe way to modify anything else is to create a replacement and commit
using the functions described in Documentation/credentials.txt (which will be
added by a later patch).
This patch and the preceding patches have been tested with the LTP SELinux
testsuite.
This patch makes several logical sets of alteration:
(1) execve().
This now prepares and commits credentials in various places in the
security code rather than altering the current creds directly.
(2) Temporary credential overrides.
do_coredump() and sys_faccessat() now prepare their own credentials and
temporarily override the ones currently on the acting thread, whilst
preventing interference from other threads by holding cred_replace_mutex
on the thread being dumped.
This will be replaced in a future patch by something that hands down the
credentials directly to the functions being called, rather than altering
the task's objective credentials.
(3) LSM interface.
A number of functions have been changed, added or removed:
(*) security_capset_check(), ->capset_check()
(*) security_capset_set(), ->capset_set()
Removed in favour of security_capset().
(*) security_capset(), ->capset()
New. This is passed a pointer to the new creds, a pointer to the old
creds and the proposed capability sets. It should fill in the new
creds or return an error. All pointers, barring the pointer to the
new creds, are now const.
(*) security_bprm_apply_creds(), ->bprm_apply_creds()
Changed; now returns a value, which will cause the process to be
killed if it's an error.
(*) security_task_alloc(), ->task_alloc_security()
Removed in favour of security_prepare_creds().
(*) security_cred_free(), ->cred_free()
New. Free security data attached to cred->security.
(*) security_prepare_creds(), ->cred_prepare()
New. Duplicate any security data attached to cred->security.
(*) security_commit_creds(), ->cred_commit()
New. Apply any security effects for the upcoming installation of new
security by commit_creds().
(*) security_task_post_setuid(), ->task_post_setuid()
Removed in favour of security_task_fix_setuid().
(*) security_task_fix_setuid(), ->task_fix_setuid()
Fix up the proposed new credentials for setuid(). This is used by
cap_set_fix_setuid() to implicitly adjust capabilities in line with
setuid() changes. Changes are made to the new credentials, rather
than the task itself as in security_task_post_setuid().
(*) security_task_reparent_to_init(), ->task_reparent_to_init()
Removed. Instead the task being reparented to init is referred
directly to init's credentials.
NOTE! This results in the loss of some state: SELinux's osid no
longer records the sid of the thread that forked it.
(*) security_key_alloc(), ->key_alloc()
(*) security_key_permission(), ->key_permission()
Changed. These now take cred pointers rather than task pointers to
refer to the security context.
(4) sys_capset().
This has been simplified and uses less locking. The LSM functions it
calls have been merged.
(5) reparent_to_kthreadd().
This gives the current thread the same credentials as init by simply using
commit_thread() to point that way.
(6) __sigqueue_alloc() and switch_uid()
__sigqueue_alloc() can't stop the target task from changing its creds
beneath it, so this function gets a reference to the currently applicable
user_struct which it then passes into the sigqueue struct it returns if
successful.
switch_uid() is now called from commit_creds(), and possibly should be
folded into that. commit_creds() should take care of protecting
__sigqueue_alloc().
(7) [sg]et[ug]id() and co and [sg]et_current_groups.
The set functions now all use prepare_creds(), commit_creds() and
abort_creds() to build and check a new set of credentials before applying
it.
security_task_set[ug]id() is called inside the prepared section. This
guarantees that nothing else will affect the creds until we've finished.
The calling of set_dumpable() has been moved into commit_creds().
Much of the functionality of set_user() has been moved into
commit_creds().
The get functions all simply access the data directly.
(8) security_task_prctl() and cap_task_prctl().
security_task_prctl() has been modified to return -ENOSYS if it doesn't
want to handle a function, or otherwise return the return value directly
rather than through an argument.
Additionally, cap_task_prctl() now prepares a new set of credentials, even
if it doesn't end up using it.
(9) Keyrings.
A number of changes have been made to the keyrings code:
(a) switch_uid_keyring(), copy_keys(), exit_keys() and suid_keys() have
all been dropped and built in to the credentials functions directly.
They may want separating out again later.
(b) key_alloc() and search_process_keyrings() now take a cred pointer
rather than a task pointer to specify the security context.
(c) copy_creds() gives a new thread within the same thread group a new
thread keyring if its parent had one, otherwise it discards the thread
keyring.
(d) The authorisation key now points directly to the credentials to extend
the search into rather pointing to the task that carries them.
(e) Installing thread, process or session keyrings causes a new set of
credentials to be created, even though it's not strictly necessary for
process or session keyrings (they're shared).
(10) Usermode helper.
The usermode helper code now carries a cred struct pointer in its
subprocess_info struct instead of a new session keyring pointer. This set
of credentials is derived from init_cred and installed on the new process
after it has been cloned.
call_usermodehelper_setup() allocates the new credentials and
call_usermodehelper_freeinfo() discards them if they haven't been used. A
special cred function (prepare_usermodeinfo_creds()) is provided
specifically for call_usermodehelper_setup() to call.
call_usermodehelper_setkeys() adjusts the credentials to sport the
supplied keyring as the new session keyring.
(11) SELinux.
SELinux has a number of changes, in addition to those to support the LSM
interface changes mentioned above:
(a) selinux_setprocattr() no longer does its check for whether the
current ptracer can access processes with the new SID inside the lock
that covers getting the ptracer's SID. Whilst this lock ensures that
the check is done with the ptracer pinned, the result is only valid
until the lock is released, so there's no point doing it inside the
lock.
(12) is_single_threaded().
This function has been extracted from selinux_setprocattr() and put into
a file of its own in the lib/ directory as join_session_keyring() now
wants to use it too.
The code in SELinux just checked to see whether a task shared mm_structs
with other tasks (CLONE_VM), but that isn't good enough. We really want
to know if they're part of the same thread group (CLONE_THREAD).
(13) nfsd.
The NFS server daemon now has to use the COW credentials to set the
credentials it is going to use. It really needs to pass the credentials
down to the functions it calls, but it can't do that until other patches
in this series have been applied.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: James Morris <jmorris@namei.org>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Make the keyring quotas controllable through /proc/sys files:
(*) /proc/sys/kernel/keys/root_maxkeys
/proc/sys/kernel/keys/root_maxbytes
Maximum number of keys that root may have and the maximum total number of
bytes of data that root may have stored in those keys.
(*) /proc/sys/kernel/keys/maxkeys
/proc/sys/kernel/keys/maxbytes
Maximum number of keys that each non-root user may have and the maximum
total number of bytes of data that each of those users may have stored in
their keys.
Also increase the quotas as a number of people have been complaining that it's
not big enough. I'm not sure that it's big enough now either, but on the
other hand, it can now be set in /etc/sysctl.conf.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: <kwc@citi.umich.edu>
Cc: <arunsr@cse.iitk.ac.in>
Cc: <dwalsh@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't generate the per-UID user and user session keyrings unless they're
explicitly accessed. This solves a problem during a login process whereby
set*uid() is called before the SELinux PAM module, resulting in the per-UID
keyrings having the wrong security labels.
This also cures the problem of multiple per-UID keyrings sometimes appearing
due to PAM modules (including pam_keyinit) setuiding and causing user_structs
to come into and go out of existence whilst the session keyring pins the user
keyring. This is achieved by first searching for extant per-UID keyrings
before inventing new ones.
The serial bound argument is also dropped from find_keyring_by_name() as it's
not currently made use of (setting it to 0 disables the feature).
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: <kwc@citi.umich.edu>
Cc: <arunsr@cse.iitk.ac.in>
Cc: <dwalsh@redhat.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The key_create_or_update() function provided by the keyring code has a default
set of permissions that are always applied to the key when created. This
might not be desirable to all clients.
Here's a patch that adds a "perm" parameter to the function to address this,
which can be set to KEY_PERM_UNDEF to revert to the current behaviour.
Signed-off-by: Arun Raghavan <arunsr@cse.iitk.ac.in>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Satyam Sharma <ssatyam@cse.iitk.ac.in>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make request_key() and co fundamentally asynchronous to make it easier for
NFS to make use of them. There are now accessor functions that do
asynchronous constructions, a wait function to wait for construction to
complete, and a completion function for the key type to indicate completion
of construction.
Note that the construction queue is now gone. Instead, keys under
construction are linked in to the appropriate keyring in advance, and that
anyone encountering one must wait for it to be complete before they can use
it. This is done automatically for userspace.
The following auxiliary changes are also made:
(1) Key type implementation stuff is split from linux/key.h into
linux/key-type.h.
(2) AF_RXRPC provides a way to allocate null rxrpc-type keys so that AFS does
not need to call key_instantiate_and_link() directly.
(3) Adjust the debugging macros so that they're -Wformat checked even if
they are disabled, and make it so they can be enabled simply by defining
__KDEBUG to be consistent with other code of mine.
(3) Documentation.
[alan@lxorguk.ukuu.org.uk: keys: missing word in documentation]
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the key serial number collision avoidance code in key_alloc_serial().
This didn't use to be so much of a problem as the key serial numbers were
allocated from a simple incremental counter, and it would have to go through
two billion keys before it could possibly encounter a collision. However, now
that random numbers are used instead, collisions are much more likely.
This is fixed by finding a hole in the rbtree where the next unused serial
number ought to be and using that by going almost back to the top of the
insertion routine and redoing the insertion with the new serial number rather
than trying to be clever and attempting to work out the insertion point
pointer directly.
This fixes kernel BZ #7727.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_KERNEL is an alias of GFP_KERNEL.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Howells