Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
System workqueues have been able to handle high level of concurrency
for a long time now and there's no reason to use dedicated workqueues
just to gain concurrency. Replace dedicated xen_pcibk_wq with the
use of system_wq.
Unlike a dedicated per-cpu workqueue created with create_workqueue(),
system_wq allows multiple work items to overlap executions even on
the same CPU; however, a per-cpu workqueue doesn't have any CPU
locality or global ordering guarantees unless the target CPU is
explicitly specified and thus the increase of local concurrency shouldn't
make any difference.
Since the work items could be pending, flush_work() has been used in
xen_pcibk_disconnect(). xen_pcibk_xenbus_remove() calls free_pdev()
which in turn calls xen_pcibk_disconnect() for every pdev to ensure that
there is no pending task while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
- Make earlyprintk=xen work for HVM guests.
- Remove module support for things never built as modules.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW8YhlAAoJEFxbo/MsZsTRiCgH/3GnL93s/BsRTrA/DYykYqA4
rPPkDd6WMlEbrko6FY7o4IxUAZ50LWU8wjmDNVTT+R/VKlWCVh2+ksxjbH8e0nzr
0QohAYTdG1VGmhkrwTjKj0wC3Nr8vaDqoBXAFRz4DiQdbobn12wzXjaVrbl8RRNc
oHDqR+DfZj6ontqx8oFkkTk7CFKIGEOtm/uBhCAV2fNkQSUCzuQyKLlarxM6jq/2
EnLR1bhnyoy5zNFzXxmaJgZOit8QFMKvPdDRknlp9yDHYJ5zolJkv+6FPiAG6SZs
A8yAUPQoAD+ekAiV2DIhb8qoNNNdZXdRCFBpoudwX3GyyU4O2P5Intl0xEg17Nk=
=L8S4
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.6-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from David Vrabel:
"Features and fixes for 4.6:
- Make earlyprintk=xen work for HVM guests
- Remove module support for things never built as modules"
* tag 'for-linus-4.6-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
drivers/xen: make platform-pci.c explicitly non-modular
drivers/xen: make sys-hypervisor.c explicitly non-modular
drivers/xen: make xenbus_dev_[front/back]end explicitly non-modular
drivers/xen: make [xen-]ballon explicitly non-modular
xen: audit usages of module.h ; remove unnecessary instances
xen/x86: Drop mode-selecting ifdefs in startup_xen()
xen/x86: Zero out .bss for PV guests
hvc_xen: make early_printk work with HVM guests
hvc_xen: fix xenboot for DomUs
hvc_xen: add earlycon support
Code that uses no modular facilities whatsoever should not be
sourcing module.h at all, since that header drags in a bunch
of other headers with it.
Similarly, code that is not explicitly using modular facilities
like module_init() but only is declaring module_param setup
variables should be using moduleparam.h and not the larger
module.h file for that.
In making this change, we also uncover an implicit use of BUG()
in inline fcns within arch/arm/include/asm/xen/hypercall.h so
we explicitly source <linux/bug.h> for that file now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Commit 8135cf8b09 (xen/pciback: Save
xen_pci_op commands before processing it) broke enabling MSI-X because
it would never copy the resulting vectors into the response. The
number of vectors requested was being overwritten by the return value
(typically zero for success).
Save the number of vectors before processing the op, so the correct
number of vectors are copied afterwards.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Commit 408fb0e5aa (xen/pciback: Don't
allow MSI-X ops if PCI_COMMAND_MEMORY is not set) prevented enabling
MSI-X on passed-through virtual functions, because it checked the VF
for PCI_COMMAND_MEMORY but this is not a valid bit for VFs.
Instead, check the physical function for PCI_COMMAND_MEMORY.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
commit f598282f51 ("PCI: Fix the NIU MSI-X problem in a better way")
teaches us that dealing with MSI-X can be troublesome.
Further checks in the MSI-X architecture shows that if the
PCI_COMMAND_MEMORY bit is turned of in the PCI_COMMAND we
may not be able to access the BAR (since they are memory regions).
Since the MSI-X tables are located in there.. that can lead
to us causing PCIe errors. Inhibit us performing any
operation on the MSI-X unless the MEMORY bit is set.
Note that Xen hypervisor with:
"x86/MSI-X: access MSI-X table only after having enabled MSI-X"
will return:
xen_pciback: 0000:0a:00.1: error -6 enabling MSI-X for guest 3!
When the generic MSI code tries to setup the PIRQ without
MEMORY bit set. Which means with later versions of Xen
(4.6) this patch is not neccessary.
This is part of XSA-157
CC: stable@vger.kernel.org
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Otherwise just continue on, returning the same values as
previously (return of 0, and op->result has the PIRQ value).
This does not change the behavior of XEN_PCI_OP_disable_msi[|x].
The pci_disable_msi or pci_disable_msix have the checks for
msi_enabled or msix_enabled so they will error out immediately.
However the guest can still call these operations and cause
us to disable the 'ack_intr'. That means the backend IRQ handler
for the legacy interrupt will not respond to interrupts anymore.
This will lead to (if the device is causing an interrupt storm)
for the Linux generic code to disable the interrupt line.
Naturally this will only happen if the device in question
is plugged in on the motherboard on shared level interrupt GSI.
This is part of XSA-157
CC: stable@vger.kernel.org
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Otherwise an guest can subvert the generic MSI code to trigger
an BUG_ON condition during MSI interrupt freeing:
for (i = 0; i < entry->nvec_used; i++)
BUG_ON(irq_has_action(entry->irq + i));
Xen PCI backed installs an IRQ handler (request_irq) for
the dev->irq whenever the guest writes PCI_COMMAND_MEMORY
(or PCI_COMMAND_IO) to the PCI_COMMAND register. This is
done in case the device has legacy interrupts the GSI line
is shared by the backend devices.
To subvert the backend the guest needs to make the backend
to change the dev->irq from the GSI to the MSI interrupt line,
make the backend allocate an interrupt handler, and then command
the backend to free the MSI interrupt and hit the BUG_ON.
Since the backend only calls 'request_irq' when the guest
writes to the PCI_COMMAND register the guest needs to call
XEN_PCI_OP_enable_msi before any other operation. This will
cause the generic MSI code to setup an MSI entry and
populate dev->irq with the new PIRQ value.
Then the guest can write to PCI_COMMAND PCI_COMMAND_MEMORY
and cause the backend to setup an IRQ handler for dev->irq
(which instead of the GSI value has the MSI pirq). See
'xen_pcibk_control_isr'.
Then the guest disables the MSI: XEN_PCI_OP_disable_msi
which ends up triggering the BUG_ON condition in 'free_msi_irqs'
as there is an IRQ handler for the entry->irq (dev->irq).
Note that this cannot be done using MSI-X as the generic
code does not over-write dev->irq with the MSI-X PIRQ values.
The patch inhibits setting up the IRQ handler if MSI or
MSI-X (for symmetry reasons) code had been called successfully.
P.S.
Xen PCIBack when it sets up the device for the guest consumption
ends up writting 0 to the PCI_COMMAND (see xen_pcibk_reset_device).
XSA-120 addendum patch removed that - however when upstreaming said
addendum we found that it caused issues with qemu upstream. That
has now been fixed in qemu upstream.
This is part of XSA-157
CC: stable@vger.kernel.org
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The guest sequence of:
a) XEN_PCI_OP_enable_msix
b) XEN_PCI_OP_enable_msix
results in hitting an NULL pointer due to using freed pointers.
The device passed in the guest MUST have MSI-X capability.
The a) constructs and SysFS representation of MSI and MSI groups.
The b) adds a second set of them but adding in to SysFS fails (duplicate entry).
'populate_msi_sysfs' frees the newly allocated msi_irq_groups (note that
in a) pdev->msi_irq_groups is still set) and also free's ALL of the
MSI-X entries of the device (the ones allocated in step a) and b)).
The unwind code: 'free_msi_irqs' deletes all the entries and tries to
delete the pdev->msi_irq_groups (which hasn't been set to NULL).
However the pointers in the SysFS are already freed and we hit an
NULL pointer further on when 'strlen' is attempted on a freed pointer.
The patch adds a simple check in the XEN_PCI_OP_enable_msix to guard
against that. The check for msi_enabled is not stricly neccessary.
This is part of XSA-157
CC: stable@vger.kernel.org
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The guest sequence of:
a) XEN_PCI_OP_enable_msi
b) XEN_PCI_OP_enable_msi
c) XEN_PCI_OP_disable_msi
results in hitting an BUG_ON condition in the msi.c code.
The MSI code uses an dev->msi_list to which it adds MSI entries.
Under the above conditions an BUG_ON() can be hit. The device
passed in the guest MUST have MSI capability.
The a) adds the entry to the dev->msi_list and sets msi_enabled.
The b) adds a second entry but adding in to SysFS fails (duplicate entry)
and deletes all of the entries from msi_list and returns (with msi_enabled
is still set). c) pci_disable_msi passes the msi_enabled checks and hits:
BUG_ON(list_empty(dev_to_msi_list(&dev->dev)));
and blows up.
The patch adds a simple check in the XEN_PCI_OP_enable_msi to guard
against that. The check for msix_enabled is not stricly neccessary.
This is part of XSA-157.
CC: stable@vger.kernel.org
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Double fetch vulnerabilities that happen when a variable is
fetched twice from shared memory but a security check is only
performed the first time.
The xen_pcibk_do_op function performs a switch statements on the op->cmd
value which is stored in shared memory. Interestingly this can result
in a double fetch vulnerability depending on the performed compiler
optimization.
This patch fixes it by saving the xen_pci_op command before
processing it. We also use 'barrier' to make sure that the
compiler does not perform any optimization.
This is part of XSA155.
CC: stable@vger.kernel.org
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
There is a missing curly brace here so we might print some extra debug
information.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Convert printks to pr_<level> (excludes printk(KERN_DEBUG...)
to be more consistent throughout the xen subsystem.
Add pr_fmt with KBUILD_MODNAME or "xen:" KBUILD_MODNAME
Coalesce formats and add missing word spaces
Add missing newlines
Align arguments and reflow to 80 columns
Remove DRV_NAME from formats as pr_fmt adds the same content
This does change some of the prefixes of these messages
but it also does make them more consistent.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
... as being guest triggerable (e.g. by invoking
XEN_PCI_OP_enable_msi{,x} on a device not being MSI/MSI-X capable).
This is CVE-2013-0231 / XSA-43.
Also make the two messages uniform in both their wording and severity.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Prior to 2.6.19 and as of 2.6.31, pci_enable_msix() can return a
positive value to indicate the number of vectors (less than the amount
requested) that can be set up for a given device. Returning this as an
operation value (secondary result) is fine, but (primary) operation
results are expected to be negative (error) or zero (success) according
to the protocol. With the frontend fixed to match the XenoLinux
behavior, the backend can now validly return zero (success) here,
passing the upper limit on the number of vectors in op->value.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This is a minor bugfix and a set of small cleanups; as it is not clear
whether this needs splitting into pieces (and if so, at what
granularity), it is a single combined patch.
- add a missing return statement to an error path in
kill_domain_by_device()
- use pci_is_enabled() rather than raw atomic_read()
- remove a bogus attempt to zero-terminate an already zero-terminated
string
- #define DRV_NAME once uniformly in the shared local header
- make DRIVER_ATTR() variables static
- eliminate a pointless use of list_for_each_entry_safe()
- add MODULE_ALIAS()
- a little bit of constification
- adjust a few messages
- remove stray semicolons from inline function definitions
Signed-off-by: Jan Beulich <jbeulich@suse.com>
[v1: Dropped the resource_size fix, altered the description]
[v2: Fixed cleanpatch.pl comments]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
- Remove the slot and controller controller backend as they
are not used.
- Document the find pciback_[read|write]_config_[byte|word|dword]
to make it easier to find.
- Collapse the code from conf_space_capability_msi into pciback_ops.c
- Collapse conf_space_capability_[pm|vpd].c in conf_space_capability.c
[and remove the conf_space_capability.h file]
- Rename all visible functions from pciback to xen_pcibk.
- Rename all the printk/pr_info, etc that use the "pciback" to say
"xen-pciback".
- Convert functions that are not referenced outside the code to be
static to save on name space.
- Do the same thing for structures that are internal to the driver.
- Run checkpatch.pl after the renames and fixup its warnings and
fix any compile errors caused by the variable rename
- Cleanup any structs that checkpath.pl commented about or just
look odd.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If we try to setup an fake IRQ handler for legacy interrupts
for devices that only have MSI-X (most if not all SR-IOV cards),
we will fail with this:
pciback[0000:01:10.0]: failed to install fake IRQ handler for IRQ 0! (rc:-38)
Since those cards don't have anything in dev->irq.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If the device that is to be shared with a guest is a level device and
the IRQ is shared with the initial domain we need to take actions.
Mainly we install a dummy IRQ handler that will ACK on the interrupt
line so as to not have the initial domain disable the interrupt line.
This dummy IRQ handler is not enabled when the device MSI/MSI-X lines
are set, nor for edge interrupts. And also not for level interrupts
that are not shared amongst devices. Lastly, if the user passes
to the guest all of the PCI devices on the shared line the we won't
install the dummy handler either.
There is also SysFS instrumentation to check its state and turn
IRQ ACKing on/off if necessary.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In cases where the guest is abruptly killed and has not disabled
MSI/MSI-X interrupts we want to do it for it.
Otherwise when the guest is started up and enables MSI, we would
get a WARN() that the device already had been enabled.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This is the host side counterpart to the frontend driver in
drivers/pci/xen-pcifront.c. The PV protocol is also implemented by
frontend drivers in other OSes too, such as the BSDs.
The PV protocol is rather simple. There is page shared with the guest,
which has the 'struct xen_pci_sharedinfo' embossed in it. The backend
has a thread that is kicked every-time the structure is changed and
based on the operation field it performs specific tasks:
XEN_PCI_OP_conf_[read|write]:
Read/Write 0xCF8/0xCFC filtered data. (conf_space*.c)
Based on which field is probed, we either enable/disable the PCI
device, change power state, read VPD, etc. The major goal of this
call is to provide a Physical IRQ (PIRQ) to the guest.
The PIRQ is Xen hypervisor global IRQ value irrespective of the IRQ
is tied in to the IO-APIC, or is a vector. For GSI type
interrupts, the PIRQ==GSI holds. For MSI/MSI-X the
PIRQ value != Linux IRQ number (thought PIRQ==vector).
Please note, that with Xen, all interrupts (except those level shared ones)
are injected directly to the guest - there is no host interaction.
XEN_PCI_OP_[enable|disable]_msi[|x] (pciback_ops.c)
Enables/disables the MSI/MSI-X capability of the device. These operations
setup the MSI/MSI-X vectors for the guest and pass them to the frontend.
When the device is activated, the interrupts are directly injected in the
guest without involving the host.
XEN_PCI_OP_aer_[detected|resume|mmio|slotreset]: In case of failure,
perform the appropriate AER commands on the guest. Right now that is
a cop-out - we just kill the guest.
Besides implementing those commands, it can also
- hide a PCI device from the host. When booting up, the user can specify
xen-pciback.hide=(1:0:0)(BDF..) so that host does not try to use the
device.
The driver was lifted from linux-2.6.18.hg tree and fixed up
so that it could compile under v3.0. Per suggestion from Jesse Barnes
moved the driver to drivers/xen/xen-pciback.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Greg Kroah-Hartman