Fix the following warning:
CC arch/arm/mach-mx5/board-mx53_loco.o
arch/arm/mach-mx5/board-mx53_loco.c:203: warning: initialization discards qualifiers from pointer target type
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The GART can only map physical memory below 1TB. Make sure
the gart driver in the kernel does not try to map memory
above 1TB.
Cc: <stable@kernel.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Link: http://lkml.kernel.org/r/1303134346-5805-5-git-send-email-joerg.roedel@amd.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The DISTLBWALKPRB bit must be set for the GART because the
gatt table is mapped UC. But the current code does not set
the bit at boot when the BIOS setup the aperture correctly.
Fix that by setting this bit when enabling the GART instead
of the other places.
Cc: <stable@kernel.org>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Link: http://lkml.kernel.org/r/1303134346-5805-4-git-send-email-joerg.roedel@amd.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Because of speculative event roll back, it is possible for some event coutners
to decrease between reads on POWER7. This causes a problem with the way that
counters are updated. Delta calues are calculated in a 64 bit value and the
top 32 bits are masked. If the register value has decreased, this leaves us
with a very large positive value added to the kernel counters. This patch
protects against this by skipping the update if the delta would be negative.
This can lead to a lack of precision in the coutner values, but from my testing
the value is typcially fewer than 10 samples at a time.
Signed-off-by: Eric B Munson <emunson@mgebm.net>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This problem was noticed on an MPC855T platform. Ftrace did oops
when trying to write to the kernel text segment.
Many thanks to Joakim for finding the root cause of this problem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We currently enable interrupts before the dispatch log for the boot
cpu is setup. If a timer interrupt comes in early enough we oops in
scan_dispatch_log:
Unable to handle kernel paging request for data at address 0x00000010
...
.scan_dispatch_log+0xb0/0x170
.account_system_vtime+0xa0/0x220
.irq_enter+0x88/0xc0
.do_IRQ+0x48/0x230
The patch below adds a check to scan_dispatch_log to ensure the
dispatch log has been allocated.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PAPR specifies that DTL buffers can not cross AMS environments (aka CMO
in the PAPR) and can not cross a memory entitlement granule boundary
(4k). This is found in section 14.11.3.2 H_REGISTER_VPA of the PAPR.
kmalloc does not guarantee an alignment of the allocation, though,
beyond 8 bytes (at least in my understanding). Create a special kmem
cache for DTL buffers with the alignment requirement.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Recent commit b987812b3f caused
a compile failure on UP because a considerably large block
of the file was included within CONFIG_SMP, hence making a stub
function not exposed on UP builds when it needed to be.
Relocate the stub to the #else /* ! CONFIG_SMP */ section
and also annotate the relevant else/endif so that nobody
else falls into the same trap I did.
Reported-by: Michael Guntsche <mike@it-loops.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: Fix warning 's3c_pm_show_resume_irqs' defined but not used
ARM: SAMSUNG: Fix build failure in PM CRC check code
ARM: S5P: Remove unused s3c_pm_check_resume_pin
Following commit 091738a266 ("genirq: Remove real old transition
functions") we removed an automatic conversion of no_irq_chip to
dummy_irq_chip. This change needs to be propagated back into the alpha
backend.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a new warning in gcc 4.6. Several of these variables are
used within #if 0 code, which probably ought to be removed. Most
of the changes are legitimate cleanups.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are outstanding gcc 4.6 warnings that need to be cleaned up
in the subdirectory. No sense forcing the issue immediately.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Issue manifests as:
In file included from arch/arm/mach-pxa/include/mach/hardware.h:62,
from arch/arm/mach-pxa/include/mach/gpio.h:28,
from /home/jic23/src/kernel/temp-remove/arch/arm/include/asm/gpio.h:5,
from include/linux/gpio.h:7,
from drivers/staging/iio/gyro/adis16080_core.c:8:
/home/jic23/src/kernel/temp-remove/arch/arm/include/asm/cputype.h:57: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'read_cpuid_id'
...
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (43 commits)
Revert "USB: isp1760-hcd: move imask clear after pending work is done"
xHCI: Implement AMD PLL quirk
xhci: Tell USB core both roothubs lost power.
usbcore: Bug fix: system can't suspend with USB3.0 device connected to USB3.0 hub
USB: Fix unplug of device with active streams
USB: xhci - also free streams when resetting devices
xhci: Fix NULL pointer deref in handle_port_status()
USB: xhci - fix math in xhci_get_endpoint_interval()
USB: xhci: simplify logic of skipping missed isoc TDs
USB: xhci - remove excessive 'inline' markings
USB: xhci: unsigned char never equals -1
USB: xhci - fix unsafe macro definitions
USB: fix formatting of SuperSpeed endpoints in /proc/bus/usb/devices
USB: isp1760-hcd: move imask clear after pending work is done
USB: fsl_qe_udc: send ZLP when zero flag and length % maxpacket == 0
usb: qcserial add missing errorpath kfrees
usb: qcserial avoid pointing to freed memory
usb: Fix qcserial memory leak on rmmod
USB: ftdi_sio: add ids for Hameg HO720 and HO730
USB: option: Added support for Samsung GT-B3730/GT-B3710 LTE USB modem.
...
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
futex: Set FLAGS_HAS_TIMEOUT during futex_wait restart setup
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_event: Fix cgrp event scheduling bug in perf_enable_on_exec()
perf: Fix a build error with some GCC versions
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix erroneous all_pinned logic
sched: Fix sched-domain avg_load calculation
* 'timer-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
RTC: rtc-mrst: follow on to the change of rtc_device_register()
RTC: add missing "return 0" in new alarm func for rtc-bfin.c
RTC: Fix s3c compile error due to missing s3c_rtc_setpie
RTC: Fix early irqs caused by calling rtc_set_alarm too early
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, amd: Disable GartTlbWlkErr when BIOS forgets it
x86, NUMA: Fix fakenuma boot failure
x86/mrst: Fix boot crash caused by incorrect pin to irq mapping
x86/ce4100: Add reg property to bridges
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6879/1: fix personality test wrt usage of domain handlers
ARM: 6878/1: fix personality flag propagation across an exec
ARM: 6877/1: the ADDR_NO_RANDOMIZE personality flag should be honored with mmap()
ARM: 6876/1: Kconfig.debug: Remove unused CONFIG_DEBUG_ERRORS
ARM: pxa: convert incorrect IRQ_TO_IRQ() to irq_to_gpio()
ARM: mmp: align NR_BUILTIN_GPIO with gpio interrupt number
ARM: pxa: align NR_BUILTIN_GPIO with GPIO interrupt number
ARM: pxa: always clear LPM bits for PXA168 MFPR
pcmcia: limit pxa2xx_trizeps4 subdriver to trizeps4 platform
pcmcia: limit pxa2xx_balloon3 subdriver to balloon3 platform
ARM: pxafb: Fix access to nonexistent member of pxafb_info
ARM: 6872/1: arch:common:Makefile Remove unused config in the Makefile.
ARM: 6868/1: Preserve the VFP state during fork
ARM: 6867/1: Introduce THREAD_NOTIFY_COPY for copy_thread() hooks
ARM: 6866/1: Do not restrict HIGHPTE to !OUTER_CACHE
ARM: 6865/1: perf: ensure pass through zero is counted on overflow
ARM: 6864/1: hw_breakpoint: clear DBGVCR out of reset
ARM: Only allow PM_SLEEP with CPUs which support suspend
ARM: Make consolidated PM sleep code depend on PM_SLEEP
This patch disables GartTlbWlk errors on AMD Fam10h CPUs if
the BIOS forgets to do is (or is just too old). Letting
these errors enabled can cause a sync-flood on the CPU
causing a reboot.
The AMD BKDG recommends disabling GART TLB Wlk Error completely.
This patch is the fix for
https://bugzilla.kernel.org/show_bug.cgi?id=33012
on my machine.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Link: http://lkml.kernel.org/r/20110415131152.GJ18463@8bytes.org
Tested-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Currently, numa=fake boot parameter is broken. If it's used,
kernel may panic due to devide by zero error depending on CPU
configuration
Call Trace:
[<ffffffff8104ad4c>] find_busiest_group+0x38c/0xd30
[<ffffffff81086aff>] ? local_clock+0x6f/0x80
[<ffffffff81050533>] load_balance+0xa3/0x600
[<ffffffff81050f53>] idle_balance+0xf3/0x180
[<ffffffff81550092>] schedule+0x722/0x7d0
[<ffffffff81550538>] ? wait_for_common+0x128/0x190
[<ffffffff81550a65>] schedule_timeout+0x265/0x320
[<ffffffff81095815>] ? lock_release_holdtime+0x35/0x1a0
[<ffffffff81550538>] ? wait_for_common+0x128/0x190
[<ffffffff8109bb6c>] ? __lock_release+0x9c/0x1d0
[<ffffffff815534e0>] ? _raw_spin_unlock_irq+0x30/0x40
[<ffffffff815534e0>] ? _raw_spin_unlock_irq+0x30/0x40
[<ffffffff81550540>] wait_for_common+0x130/0x190
[<ffffffff81051920>] ? try_to_wake_up+0x510/0x510
[<ffffffff8155067d>] wait_for_completion+0x1d/0x20
[<ffffffff8107f36c>] kthread_create_on_node+0xac/0x150
[<ffffffff81077bb0>] ? process_scheduled_works+0x40/0x40
[<ffffffff8155045f>] ? wait_for_common+0x4f/0x190
[<ffffffff8107a283>] __alloc_workqueue_key+0x1a3/0x590
[<ffffffff81e0cce2>] cpuset_init_smp+0x6b/0x7b
[<ffffffff81df3d07>] kernel_init+0xc3/0x182
[<ffffffff8155d5e4>] kernel_thread_helper+0x4/0x10
[<ffffffff81553cd4>] ? retint_restore_args+0x13/0x13
[<ffffffff81df3c44>] ? start_kernel+0x400/0x400
[<ffffffff8155d5e0>] ? gs_change+0x13/0x13
The divede by zero is caused by the following line,
group->cpu_power==0:
kernel/sched_fair.c::update_sg_lb_stats()
/* Adjust by relative CPU power of the group */
sgs->avg_load = (sgs->group_load * SCHED_LOAD_SCALE) / group->cpu_power;
This regression was caused by commit e23bba6044 ("x86-64, NUMA: Unify
emulated distance mapping") because it changes cpu -> node
mapping in the process of dropping fake_physnodes().
old) all cpus are assinged node 0
now) cpus are assigned round robin
(the logic is implemented by numa_init_array())
Note: The change in behavior only happens if the system doesn't
have neither ACPI SRAT table nor AMD northbridge NUMA
information.
Round robin assignment doesn't work because init_numa_sched_groups_power()
assumes all logical cpus in the same physical cpu share the same node
(then it only accounts for group_first_cpu()), and the simple round robin
breaks the above assumption.
Thus, this patch implements a reassignment of node-ids if buggy firmware
or numa emulation makes wrong cpu node map. Tt enforce all logical cpus
in the same physical cpu share the same node.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Shaohui Zheng <shaohui.zheng@intel.com>
Cc: David Rientjes <rientjes@google.com>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/20110415203928.1303.A69D9226@jp.fujitsu.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 8a5ec0ba "Lockless (and preemptless) fastpaths for slub" makes use
of this_cpu_cmpxchg_double() which needs this_cpu_cmpxchg16b_emu() on
x86_64. Implementing cmpxchg16b emulation for UML would introduce too
much complexity. So just disable it.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reported-by: Sergei Trofimovich <slyich@gmail.com>
Acked-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 1de1502c ("x86, um: now we can get rid of trivial uml headers")
removed accidentally bug.h which broke UML's call tracer and bug
handler.
Without asm-generic/bug.h UML uses BUG() from arch/x86/ which makes use
of ud2. UML cannot use ud2, it raises SIGILL in user mode. As UML has
a different stack for handling signals the call trace will be cut off.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reported-by: Sergei Trofimovich <slyich@gmail.com>
Tested-by: Sergei Trofimovich <slyich@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a possible problem with mport registration left non-cleared after
fsl_rio_setup() exits on link error. Abort mport initialization if
registration failed.
This patch is applicable to 2.6.39-rc1 only. The problem does not exist
for earlier versions.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are optional bits that may complement a personality ID. It is
therefore wrong to simply test against the absolute current->personality
value to determine the effective personality. The PER_LINUX_32BIT is
itself just PER_LINUX with one of those optional bits set.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Our SET_PERSONALITY() implementation was overwriting all existing
personality flags, including ADDR_NO_RANDOMIZE, making them unavailable
to processes being exec'd after a call to personality() in user space.
This prevents the gdb test suite from running successfully.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This config option isn't actually used anywhere and can be safely
removed. The last user was traps.c before commit 082f47a ([ARM]
always allow dump_stack() to produce a backtrace, 2007-07-05).
Reviewed-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
s3c_pm_show_resume_irqs() is used by some s3c_pm_arch_show_resume_irqs()
implementations, which get included through mach/pm-core.h. Add __maybe_unused
to silence warnings when it isn't used (e.g. on S3C64XX platforms).
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes build error that occurs on enabling the Samsung
specific PM CRC check code. Missed removing this reference of
s3c_sleep_save_phys during move to generic cpu suspend/resume
support.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The s3c_pm_check_resume_pin() is not being used and can be safely
removed to fix the build warning.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The recent commit (10774912647781) wasn't entirely correct. While
it fixed some issues, it introduced others. So pull in the fixes
from the public cache flush functions, and document why we need to
call things directly ourselves.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If the period of a gptimer is fairly low, we might miss an interrupt
by acking it too late (we end up acking the new int as well).
Reported-by: Isabelle Leonardi <i.leonardi@detracom.fr>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We only want to clear the run bit for this one timer, not all status bits.
So don't read the whole reg and then write all the bits back out.
Reported-by: Isabelle Leonardi <i.leonardi@detracom.fr>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When suspending/resuming, the common task freezing code will run in
parallel and freeze processes on each core. This is because the code
uses the non-smp version of memory barriers (as well it should).
The Blackfin smp barrier logic at the moment contains the cache sync
logic, but the non-smp barriers do not. This is incorrect as Rafel
summarized:
> ...
> The existing memory barriers are SMP barriers too, but they are more
> than _just_ SMP barriers. At least that's how it is _supposed_ to be
> (eg. rmb() is supposed to be stronger than smp_rmb()).
> ...
> However, looking at the blackfin's definitions of SMP barriers I see
> that it uses extra stuff that should _also_ be used in the definitions
> of the mandatory barriers.
> ...
URL: http://lkml.org/lkml/2011/4/13/11
LKML-Reference: <BANLkTi=F-C-vwX4PGGfbkdTBw3OWL-twfg@mail.gmail.com>
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Disable USB_ARCH_HAS_EHCI in arch Kconfig and enable it in usb Kconfig
Warning log:
warning: (MICROBLAZE) selects USB_ARCH_HAS_EHCI which has unmet
direct dependencies (USB_SUPPORT)
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Register the dfbmcs320 device which provides the PCM DAI for the bluetooth
module.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/avr32-2.6:
avr32: add ATAG_BOARDINFO
don't check platform_get_irq's return value against zero
avr32: init cannot ignore signals sent by force_sig_info()
avr32: fix deadlock when reading clock list in debugfs
avr32: Fix .size directive for cpu_enter_idle
avr32: At32ap: pio fix typo "))" on gpio_irq_unmask prototype
fix the wrong argument of the functions definition
The ATAG_BOARDINFO is intended to hand over the information
bd->bi_board_number from u-boot to the kernel.
This piece of information can be used to implement some kind of board
identification while booting the kernel. Therefore it is placed in .initdata
section and can be accessed via the new symbol board_number only while
initializing the kernel.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
platform_get_irq returns -ENXIO on failure, so !int_irq was probably
always true. Better use (int)int_irq <= 0. Note that a return value of
zero is still handled as error even though this could mean irq0.
This is a followup to 305b3228f9 that
changed the return value of platform_get_irq from 0 to -ENXIO on error.
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
We can delete the code that checks to see if we're sending an ignored
signal to init because force_sig_info() already handles this case.
force_sig_info() will kill init even if the signal handler is SIG_DFL
and the scenario described in the comment where init might "generate
the same exception over and over again" cannot occur (force_sig_info()
clears SIGNAL_UNKILLABLE to ensure that init will die).
Also, the use of is_global_init() is not correct in the multhreaded
case, as Oleg Nesterov explains,
"is_global_init() is not right in theory, /sbin/init can be
multithreaded. And, this doesn't cover the sub-namespace
inits... I'd suggest to check SIGNAL_UNKILLABLE, but looking
closer I think you can simply remove this code."
It seems this code was copied from arch/powerpc in March 2007 in commit
623b0355d5 "[AVR32] Clean up exception handling code"
but the code was deleted from arch/powerpc in November 2009 in commit
a0592d42fe "powerpc: kill the obsolete code under is_global_init()"
So catch up with powerpc and delete the bogus code.
Signed-off-by: Matt Fleming <matt.fleming@linux.intel.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
When writing out /sys/kernel/debug/at32ap_clk, clock list lock is being
held while clk_get() is called. clk_get() attempts to take the same
lock, which results in deadlock. Introduce and call lock free version,
__clk_get(), instead.
Signed-off-by: Ole Henrik Jahren <olehenja@alumni.ntnu.no>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
gas used to accept (and ignore?) .size directives which referred to
undefined symbols, as this does. In binutils 2.21 these are treated
as errors.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
The functions of eic_chip's memebers use the wrong argument .
Signed-off-by: Wanlong Gao <wanlong.gao@gmail.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
This fixes the failure to register the IRQ_RTCAlrm alarm as a wakeup
event. It is misinterpreted as a gpio irq not a PWER bitmask. Fixed
this by converting the incorrect IRQ_TO_IRQ() to a correct version of
irq_to_gpio().
Reported-by: Nick Bane <nickbane1@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Avoid to mismatch between NR_BUILTIN_GPIO and gpio interrupt number.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Avoid to mismatch between NR_BUILTIN_GPIO and GPIO interrupt number
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
We currently dont have CPU Hotplug support working on 85xx so we need to
disable Suspsend support as it will force enabling of CPU Hotplug.
arch/powerpc/kernel/built-in.o: In function `cpu_die': arch/powerpc/kernel/smp.c:702: undefined reference to `start_secondary_resume'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
e500mc does not support the HID0/MSR mechanism that is used by e500_idle
(and there are also issues with waking on certain types of interrupts).
Further, even if napping is never actually enabled, just having
CPU_FTR_CAN_NAP will cause machine_init() to overwrite the board's supplied
ppc_md.power_save().
We drop CPU_FTR_MAYBE_CAN_DOZE becuase we should use 'wait' instead on
e500mc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The CPU_FTRS_POSSIBLE and CPU_FTRS_ALWAYS defines did not encompass
e5500 CPU features when built for 64-bit. This causes issues with
cpu_has_feature() as it utilizes the POSSIBLE & ALWAYS defines as part
of its check.
Create a unique CPU_FTRS_E5500 (as its different from CPU_FTRS_E500MC),
created a new group for 64-bit Book3e based CPUs and add CPU_FTRS_E5500
to that group.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
serial port nodes with the property status="disabled" are not usable and so
avoid adding "disabled" port with the system.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PCIe nodes with the property status="disabled" are not usable and so
avoid adding "disabled" PCIe bridge with the system.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The irq_set_wake() function of the gpio irq_chip calls
enable/disable_irq_wake() on the demultiplex interrupt. That leads to
a lockdep warning "INFO: possible recursive locking detected" because
irq_set_type() is called under irq_desc->lock and the *_irq_wake()
calls take irq_desc->lock of the demux interrupt.
Tell lockdep that the gpio irqs are in a different lock class.
Documentation/SubmitChecklist:
15: All codepaths have been exercised with all lockdep features enabled.
That's a non-optional requirement, AFAICT.
Reported-and-tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LAKML-Reference: alpine.LFD.2.00.1104041416290.19945@localhost6.localdomain6
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a
result, using these directives in code sections can result in
misaligned data words when building a Thumb-2 kernel
(CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to
assume that fundamental types of word size or above are word-
aligned when accessing them from C. If the data is not really
word-aligned, this can cause impaired performance and stray
alignment faults in some circumstances.
In general, the following rules should be applied when using
data word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
LAKML-Reference: 1289913217-8672-1-git-send-email-dave.martin@linaro.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For the lcdif clock get_rate looks as follows:
read div from HW_CLKCTRL_DIS_LCDIF.DIV
return clk_get_rate(clk->parent) / div
with clk->parent being ref_pix_clk on my system.
ref_pix_clk's rate depends on HW_CLKCTRL_FRAC1.PIXFRAC.
The set_rate function for lcdif does:
parent_rate = clk_get_rate(clk->parent);
based on that calculate frac and div such that
parent_rate * 18 / frac / div is near the requested rate.
HW_CLKCTRL_FRAC1.PIXFRAC is updated with frac
HW_CLKCTRL_DIS_LCDIF.DIV is updated with div
For this calculation to be correct parent_rate needs to be
initialized not with the clock rate of lcdif's parent (i.e. ref_pix) but
that of its grandparent (i.e. ref_pix' parent == pll0_clk).
The obvious downside of this patch is that now set_rate(lcdif) changes
its parent's rate, too. Still this is better than a wrong rate.
Acked-by: Shawn Guo <shawn.guo@freescale.com>
LAKML-Reference: 20110225084950.GA13684@S2101-09.ap.freescale.net
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This was broken by
4bd597b (ARM i.MX ehci: do ehci init in board specific functions)
and fixes:
CC arch/arm/mach-mx3/mach-vpr200.o
arch/arm/mach-mx3/mach-vpr200.c:263: error: unknown field 'flags' specified in initializer
arch/arm/mach-mx3/mach-vpr200.c:264: warning: initialization makes pointer from integer without a cast
by just applying the change to mach-vpr200.c that the other machine files
got by 4bd597b.
LAKML-Reference: 1302257029-17397-1-git-send-email-u.kleine-koenig@pengutronix.de
Acked-by: Marc Reilly <marc@cpdesign.com.au>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Moorestown systems crash on boot because the secondary CPU
clockevent (apbt1) will fail to request irq#1, which does not
have ioapic chip in its irq_desc[] entry.
Background:
Moorestown platform does not have ISA bus nor legacy IRQs. It
reuses the range of legacy IRQs for regular device interrupts.
The routing information of early system device IRQs (timers) are
obtained from firmware provided SFI tables. We reuse/fake MP
configuration table to facilitate IRQ setup with IOAPIC.
Maintaining a 1:1 mapping of IOAPIC pin (RTE entry) and IRQ#
makes routing information clean and easy to understand on
Moorestown. Though optional.
This patch allows SFI timer and vRTC IRQ to be treated as ISA
IRQ so that pin2irq mapping will be 1:1.
Also fixed MP table type and use macros to clearly set MP IRQ
entries. As a result, apbt timer and RTC interrupts on
Moorestown are within legacy IRQ range:
# cat /proc/interrupts
CPU0 CPU1
0: 11249 0 IO-APIC-edge apbt0
1: 0 12271 IO-APIC-edge apbt1
8: 887 0 IO-APIC-fasteoi dw_spi
13: 0 0 IO-APIC-fasteoi INTEL_MID_DMAC2
14: 0 0 IO-APIC-fasteoi rtc0
Further discussion of this patch can be found at:
https://lkml.org/lkml/2010/6/10/70
Suggested-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Link: http://lkml.kernel.org/r/1302286980-21139-1-git-send-email-jacob.jun.pan@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'stable/bug-fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: Allow PV-OPS kernel to detect whether XSAVE is supported
xen: just completely disable XSAVE
xen/debug: Don't be so verbose with WARN on 1-1 mapping errors.
xen: events: fix error checks in bind_*_to_irqhandler()
Make XEN_SAVE_RESTORE select HIBERNATE_CALLBACKS.
Remove XEN_SAVE_RESTORE dependency from PM_SLEEP.
Signed-off-by: Shriram Rajagopalan <rshriram@cs.ubc.ca>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Xen save/restore is going to use hibernate device callbacks for
quiescing devices and putting them back to normal operations and it
would need to select CONFIG_HIBERNATION for this purpose. However,
that also would cause the hibernate interfaces for user space to be
enabled, which might confuse user space, because the Xen kernels
don't support hibernation. Moreover, it would be wasteful, as it
would make the Xen kernels include a substantial amount of code that
they would never use.
To address this issue introduce new power management Kconfig option
CONFIG_HIBERNATE_CALLBACKS, such that it will only select the code
that is necessary for the hibernate device callbacks to work and make
CONFIG_HIBERNATION select it. Then, Xen save/restore will be able to
select CONFIG_HIBERNATE_CALLBACKS without dragging the entire
hibernate code along with it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Shriram Rajagopalan <rshriram@cs.ubc.ca>
without the reg property Ben's new code won't find the PCI & ISA
bridge and the devices won't get the DT-node attached.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: monstr@monstr.eu
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Link: http://lkml.kernel.org/r/20110407121315.GA9204@linutronix.de
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The patch below removes an unused config variable found by using a kernel
cleanup script.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
VFP registers d16-d31 are callee saved registers and must be preserved
during function calls, including fork(). The VFP configuration should
also be preserved. The patch copies the full VFP state to the child
process.
Reported-by: Paul Wright <paul.wright@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds THREAD_NOTIFY_COPY for calling registered handlers
during the copy_thread() function call. It also changes the VFP handler
to use a switch statement rather than if..else and ignore this event.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The HIGHPTE config option depends on !OUTER_CACHE. However, there is no
set_pte_ext() function that does outer cache maintenance by physical
address, hence no need for such restriction.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit a737823d ("ARM: perf: ensure overflows aren't missed due to IRQ
latency") changed the way that event deltas are calculated on overflow
so that we don't miss events when the new count value overtakes the
previous one.
Unfortunately, we forget to count the event that passes through zero so
we end up being off by 1. This patch adds on the correction.
Reported-by: Chris Moore <moore@free.fr>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DBGVCR, used for configuring vector catch debug events, is UNKNOWN
out of reset on ARMv7. When enabling monitor mode, this must be zeroed
to avoid UNPREDICTABLE behaviour.
This patch adds the zeroing code to the debug reset path.
Cc: stable <stable@kernel.org>
Reported-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
efifb: Add override for 11" Macbook Air 3,1
efifb: Support overriding fields FW tells us with the DMI data.
fb: Reduce priority of resource conflict message
savagefb: Remove obsolete else clause in savage_setup_i2c_bus
savagefb: Set up I2C based on chip family instead of card id
savagefb: Replace magic register address with define
drivers/video/bfin-lq035q1-fb.c: introduce missing kfree
video: s3c-fb: fix checkpatch errors and warning
efifb: support AMD Radeon HD 6490
s3fb: fix Virge/GX2
fbcon: Remove unused 'display *p' variable from fb_flashcursor()
fbdev: sh_mobile_lcdcfb: fix module lock acquisition
fbdev: sh_mobile_lcdcfb: add blanking support
viafb: initialize margins correct
viafb: refresh rate bug collection
sh: mach-ap325rxa: move backlight control code
sh: mach-ecovec24: support for main lcd backlight
* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
ARM: arch-shmobile: only run FSI init on respective boards
ARM: arch-shmobile: only run HDMI init on respective boards
ARM: mach-shmobile: Correctly check for CONFIG_MACH_MACKEREL
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, fpu: Fix FPU exception handling on non-SSE systems
x86, hibernate: Initialize mmu_cr4_features during boot
x86-32, NUMA: Fix ACPI NUMA init broken by recent x86-64 change
x86: visws: Fixup irq overhaul fallout
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Clean up rebalance_domains() load-balance interval calculation
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/mrst/vrtc: Fix boot crash in mrst_rtc_init()
rtc, x86/mrst/vrtc: Fix boot crash in rtc_read_alarm()
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Fix cpumask leak in __setup_irq()
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf probe: Fix listing incorrect line number with inline function
perf probe: Fix to find recursively inlined function
perf probe: Fix multiple --vars options behavior
perf probe: Fix to remove redundant close
perf probe: Fix to ensure function declared file
The sfi_mrtc_array[] only gets initialized when the sfi mrtc
table is parsed, so the vrtc_paddr should be initalized after it
too.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1302140389-27603-1-git-send-email-feng.tang@intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Restore the initialization of mmu_cr4_features during boot, which was
removed without comment in checkin e5f15b45dd
x86: Cleanup highmap after brk is concluded
thereby breaking resume from hibernate. This restores previous
functionality in approximately the same place, and corrects the
reading of %cr4 on pre-CPUID hardware (%cr4 exists if and only if
CPUID is supported.)
However, part of the problem is that the hibernate suspend/resume
sequence should manage the save/restore of %cr4 explicitly.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <201104020154.57136.rjw@sisk.pl>
Now that everything that was using these interfaces has been converted to
the syscore ops, prevent new code from using the old API.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If several boards are enabled in the kernel configuration,
fsi_init_pm_clock() functions from board-ap4evb.c
will run on any of them. Prevent this by calling these functions from the
.init_machine() callback instead of using device_initcall().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If several boards are enabled in the kernel configuration,
hdmi_init_pm_clock() functions from board-ap4evb.c and board-mackerel.c
will run on any of them. Prevent this by calling these functions from the
.init_machine() callback instead of using device_initcall().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
I made a bit of a thinko when adding Mackerel to the boards
that support zboot using MMCIF.
Reported-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Xen fails to mask XSAVE from the cpuid feature, despite not historically
supporting guest use of XSAVE. However, now that XSAVE support has been
added to Xen, we need to reliably detect its presence.
The most reliable way to do this is to look at the OSXSAVE feature in
cpuid which is set iff the OS (Xen, in this case), has set
CR4.OSXSAVE.
[ Cleaned up conditional a bit. - Jeremy ]
Signed-off-by: Shan Haitao <haitao.shan@intel.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Some (old) versions of Xen just kill the domain if it tries to set any
unknown bits in CR4, so we can't reliably probe for OSXSAVE in
CR4.
Since Xen doesn't support XSAVE for guests at the moment, and no such
support is being worked on, there's no downside in just unconditionally
masking XSAVE support.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If KVM cannot find an exact match for a requested CPUID leaf, the
code will try to find the closest match instead of simply confessing
it's failure.
The implementation was meant to satisfy the CPUID specification, but
did not properly check for extended and standard leaves and also
didn't account for the index subleaf.
Beside that this rule only applies to CPUID intercepts, which is not
the only user of the kvm_find_cpuid_entry() function.
So fix this algorithm and call it from kvm_emulate_cpuid().
This fixes a crash of newer Linux kernels as KVM guests on
AMD Bulldozer CPUs, where bogus values were returned in response to
a CPUID intercept.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
When KVM scans the 0xD CPUID leaf for propagating the XSAVE save area
leaves, it assumes that the leaves are contigious and stops at the
first zero one. On AMD hardware there is a gap, though, as LWP uses
leaf 62 to announce it's state save area.
So lets iterate through all 64 possible leaves and simply skip zero
ones to also cover later features.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Commit b3df895aeb "powerpc/kexec: Add support for FSL-BookE"
introduced the original PPC_STD_MMU_64 checks around the function
crash_kexec_wait_realmode(). Then commit c2be05481f
"powerpc: Fix default_machine_crash_shutdown #ifdef botch" changed
the ifdef around the calling site to add a check on SMP, but the
ifdef around the function itself was left unchanged, leaving an
unused function for PPC_STD_MMU_64=y and SMP=n
Rather than have two ifdefs that can get out of sync like this,
simply put the corrected conditional around the function and use
a stub to get rid of one set of ifdefs completely.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix some minor typos:
* informations => information
* there own => their own
* these => this
Signed-off-by: Sylvestre Ledru <sylvestre.ledru@scilab.org>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are valid situations in which this error is not
a warning. Mainly when QEMU maps a guest memory and uses
the VM_IO flag to set the MFNs. For right now make the
WARN be WARN_ONCE. In the future we will:
1). Remove the VM_IO code handling..
2). .. which will also remove this debug facility.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, UV: Fix kdump reboot
x86, amd-nb: Rename CPU PCI id define for F4
sound: Add delay.h to sound/soc/codecs/sn95031.c
x86, mtrr, pat: Fix one cpu getting out of sync during resume
x86, microcode: Unregister syscore_ops after microcode unloaded
x86: Stop including <linux/delay.h> in two asm header files
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: create new rcu_access_index() and use in mce
WARN_ON_SMP(): Add comment to explain ({0;})
* 'unicore32' of git://git.kernel.org/pub/scm/linux/kernel/git/epip/linux-2.6-unicore32:
unicore32 framebuffer fix: get videomemory by __get_free_pages() and make it floatable
unicore32 core architecture: remove duplicated #include
unicore32 rtc driver fix: cleanup irq_set_freq and irq_set_state
unicore32 fix: remove arch-specific futex support
unicore32 ldscript fix: add cacheline parameter to PERCPU() macro
Commit d8fc3afc49 (x86, NUMA: Move *_numa_init() invocations
into initmem_init()) moved acpi_numa_init() call into NUMA
initmem_init() but forgot to update 32bit NUMA init breaking ACPI
NUMA configuration for 32bit.
acpi_numa_init() call was later moved again to srat_64.c. Match
it by adding the call to get_memcfg_from_srat() in srat_32.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Cc: H. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <20110404100645.GE1420@mtj.dyndns.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
PCIe memory address space is 1:1 mapped with u-boot.
Update dts of Px020RDB i.e. P1020RDB and P2020RDB to match the address map
changes in u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The latest binutils won't accept the stfl instruction with march=g5
which is the correct behaviour. Unfortunately head.S is assembled
with -march=g5 even if the target cpu is z900 or later. To get
31-bit kernels compiled again the easiest fix is to use the .insn
notation for the stfl instruction in head.S.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After the execution has been switched to the destination CPU, the target
function is called with the wrong parameter. According to the C calling
convention on s390, the first parameter should be loaded into register 2.
Currently in smp_restart_cpu() it is stored in register 3. To fix this, we
load the parameter into the correct register 2.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Prevent stack corruption by memcpy which copies more bytes then
available at the destination. While at it use the new test_facility
to test for the facility bit.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Offering CONFIG_PM_SLEEP for CPUs which do not support suspend leads to
build errors, so only set CONFIG_ARCH_SUSPEND_POSSIBLE if we have a CPU
selected which supports suspend.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CONFIG_PM is now set whenever we support either runtime PM in addition
to suspend and hibernate. This causes build errors when runtime PM is
enabled on a platform, but the CPU does not have the appropriate support
for suspend.
So, switch this code to use CONFIG_PM_SLEEP rather than CONFIG_PM to
allow runtime PM to be enabled without causing build errors.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The futex functions in unicore32 are not used and verified,
so just replaced by asm-generic version.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Checking 'rate < 0' doesn't work because 'rate' is unsigned.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Colin Cross <ccross@android.com>
In commit f5e5bf088b
ia64: Use irqd_irq_disabled() instead of desc->status access
Thomas forgot to convert from irq to *irq_data.
Add a call to irq_get_irq_data() to fix that.
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
kdump: Allow shrinking of kdump region to be overridden
powerpc/pmac/smp: Remove no-longer needed preempt workaround
powerpc/smp: Increase vdso_data->processorCount, not just decrease it
powerpc/smp: Create idle threads on demand and properly reset them
powerpc/smp: Don't expose per-cpu "cpu_state" array
powerpc/pmac/smp: Fix CPU hotplug crashes on some machines
powerpc/smp: Add a smp_ops->bringup_up() done callback
powerpc/pmac: Rename cpu_state in therm_pm72 to avoid collision
powerpc/pmac/smp: Properly NAP offlined CPU on G5
powerpc/pmac/smp: Remove HMT changes for PowerMac offline code
powerpc/pmac/smp: Consolidate 32-bit and 64-bit PowerMac cpu_die in one file
powerpc/pmac/smp: Fixup smp_core99_cpu_disable() and use it on 64-bit
powerpc/pmac/smp: Rename fixup_irqs() to migrate_irqs() and use it on ppc32
powerpc/pmac/smp: Fix 32-bit PowerMac cpu_die
powerpc/smp: Remove unused smp_ops->cpu_enable()
powerpc/smp: Remove unused generic_cpu_enable()
powerpc/smp: Fix generic_mach_cpu_die()
powerpc/smp: soft-replugged CPUs must go back to start_secondary
powerpc: Make decrementer interrupt robust against offlined CPUs
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc32: Pass task_struct to schedule_tail() in ret_from_fork
apbuart: Depend upon sparc.
sparc64: Fix section mis-match errors.
sparc32,leon: Fixed APBUART frequency detection
sparc32, leon: APBUART driver must use archdata to get IRQ number
sparc: Hook up syncfs system call.
The MCE subsystem needs to sample an RCU-protected index outside of
any protection for that index. If this was a pointer, we would use
rcu_access_pointer(), but there is no corresponding rcu_access_index().
This commit therefore creates an rcu_access_index() and applies it
to MCE.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Zdenek Kabelac <zkabelac@redhat.com>
- Do not trace idle loop which takes a lot time
- Fix cache handling in generic ftrace code
- Do not trace lib functions ashldi3, ashrdi3, lshrdi3
Functions are called from generic ftrace code which
can't be traced
Signed-off-by: Michal Simek <monstr@monstr.eu>
Instead of creating idle threads at boot for all possible CPUs, we
create them on demand, like x86 or ARM, and we properly call init_idle
to re-initialize an idle thread when a CPU was unplugged and is now
re-plugged.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Instead, keep it static, expose an accessor and use that from
the PowerMac code. Avoids easy namespace collisions and will
make it easier to consolidate with other implementations.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On some machines that use i2c to synchronize the timebases (such
as PowerMac7,2/7,3 G5 machines), hotplug CPU would crash when
putting back a new CPU online due to the underlying i2c bus being
closed.
This uses the newly added bringup_done() callback to move the close
along with other housekeeping calls, and adds a CPU notifier to
re-open the i2c bus around subsequent hotplug operations
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This allows us to stop abusing smp_ops->setup_cpu() for cleanup
tasks that have to take place after the initial boot time CPU
bringup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current code soft-disables, and then goes to NAP mode which
turns interrupts on. That means that if an interrupt occurs, we
will hit the masked interrupt code path which isn't what we want,
as it will return with EE off, which will either get us out of
NAP mode, or fail to enter it (according to spec).
Instead, let's just rely on the fact that it is safe to take
decrementer interrupts on an offline CPU and leave interrupts
enabled. We can also get rid of the special case in asm for
power4_cpu_offline_powersave() and just use power4_idle().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Those instructions do nothing on non-threaded processors such
as 970's used on those machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the generic code, just add the MPIC priority setting,
I don't see any use in mucking around with the decrementer,
as 32-bit will have EE off all along, and 64-bit will be able
to deal with it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use generic cpu_state, call idle_task_exit() properly, and
remove smp_core99_cpu_die() which isn't useful, the generic
function does the job just fine.
Remove the last remnants of cpu_enable(), everybody uses the normal
__cpu_up() path now
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is used by some "soft" hotplug implementations. I needs to
call idle_task_exit() when the CPU is going away, and we remove
the now no-longer needed set_cpu_online() and local_irq_enable()
which are handled by the return to start_secondary
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Various thing are torn down when a CPU is hot-unplugged. That CPU
is expected to go back to start_secondary when re-plugged to re
initialize everything, such as clock sources, maps, ...
Some implementations just return from cpu_die() callback
in the idle loop when the CPU is "re-plugged". This is not enough.
We fix it using a little asm trampoline which resets the stack
and calls back into start_secondary as if we were all fresh from
boot. The trampoline already existed on ppc64, but we add it for
ppc32
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With some implementations, it is possible that a timer interrupt
occurs every few seconds on an offline CPU. In this case, just
re-arm the decrementer and return immediately
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Change af90f10d38 "ARM: 6759/1: smp: Select local timers vs broadcast
timer support runtime" missed a return statement, causing a compile
warning:
arch/arm/mach-msm/timer.c:272: warning: 'return' with no value, in
function returning non-void
Trivially return 0 for success when running on cpu 0 (to match the
comment and previous behavior).
Signed-off-by: David Brown <davidb@codeaurora.org>
The qsd8x50 board file contains a few references to machine_is_...
macros that are otherwise unused, and contain no machine definition.
The recent purge of unused machine definitions breaks the compilation
of this target.
Since the machine cannot ever be used, just remove the bogus checks.
Signed-off-by: David Brown <davidb@codeaurora.org>
After a crash dump on an SGI Altix UV system the crash kernel
fails to cause a reboot. EFI mode is disabled in the kdump
kernel, so only the reboot_type of BOOT_ACPI works.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: rja@sgi.com
LKML-Reference: <E1Q5Iuo-00013b-UK@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We have to pass task_struct of previous process to function
schedule_tail(). Currently in ret_from_fork previous thread_info
is passed:
switch_to: mov %g6, %g3 /* previous thread_info in g6 */
ret_from_fork: call schedule_tail
mov %g3, %o0 /* previous thread_info is passed */
void schedule_tail(struct task_struct *prev);
Signed-off-by: Tkhai Kirill <tkhai@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
With increasing number of PCI function ids, add the PCI function
id in the define name instead of its symbolic name in the BKDG
for more clarity. This renames function 4 define.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <20110330183447.GA3668@aftab>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix the problem that the sh_mobile_sdhi.h changed the directory from
"linux/mfd/" to "linux/mmc/".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix all of the problems spotted by CONFIG_DEBUG_SECTION_MISMATCH under
arch/sparc during a 64-bit defconfig build.
They fall into two categorites:
1) of_device_id is marked as __initdata, and we can never do this
since these objects sit in the device core data structures way
past boot. So even if a driver will never be reloaded, we have
to keep the device ID table around.
Mark such cases const instead.
2) The bootmem alloc/free handling code in mdesc.c was not fully
marked __init as it should be, thus generating a reference
to free_bootmem_late() (which is __init) from non-__init code.
Signed-off-by: David S. Miller <davem@davemloft.net>
Change b0f18edaf6
(arm: tegra: Remove unused bogus irq enable/disable magic)
introduces warnings:
arch/arm/mach-tegra/gpio.c: In function 'tegra_gpio_resume':
arch/arm/mach-tegra/gpio.c:260: warning: unused variable 'i'
arch/arm/mach-tegra/gpio.c: In function 'tegra_gpio_suspend':
arch/arm/mach-tegra/gpio.c:283: warning: unused variable 'i'
Fix them, and fix a coding style issue on the same lines.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Erik Gilling <konkers@konkers.net>
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
avr32: Fix missing irq namespace conversion
powerpc: qe_ic: Rename get_irq_desc_data and get_irq_desc_chip
genirq: Remove the now obsolete config options and select statements
arm: versatile : Fix typo introduced in irq namespace cleanup
sound: Fixup the last user of the old irq functions
genirq: Remove obsolete comment
genirq: Remove now obsolete set_irq_wake()
sh: Fix irq cleanup fallout
x86: apb_timer: Fixup genirq fallout
genirq: Fix misnamed label in handle_edge_eoi_irq
Fix up crazy conflict in arch/powerpc/include/asm/qe_ic.h:
- commit eead4d5c63 ("powerpc: qe_ic: Rename get_irq_desc_data and
get_irq_desc_chip") made the helper functions use
irq_desc_get_handler_data() instead of the legacy (and no longer
existing) get_irq_desc_data.
- commit d4db35e8dc ("powerpc/qe_ic: Fix another breakage from the
irq_data conversion") used irq_desc_get_chip_data() instead.
According to Thomas, the former is the correct direct conversion, but it
does look like both should work (arch/powerpc/sysdev/qe_lib/qe_ic.c
seems to initialize both to the same thing), and the chip data in some
ways is the more logical. Somebody should really decide on one of the
other.
This merge picks irq_desc_get_handler_data() as the straightforward pure
conversion to new names, as per Thomas.
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/qe_ic: Fix another breakage from the irq_data conversion
powerpc/8xx: Fix another breakage from the irq_data conversion
powerpc/cell: Use handle_edge_eoi_irq for real
powerpc/pseries: Enable Chelsio network and iWARP drivers
powerpc/mm: Move the STAB0 location to 0x8000 to make room in low memory
powerpc: Fix accounting of softirq time when idle
powerpc/pseries/smp: query-cpu-stopped-state support won't change
powerpc/xics: Use hwirq for xics domain irq number
powerpc/xics: Fix numberspace mismatch from irq_desc conversion
powerpc: Wire up new syscalls
powerpc/booke: Correct the SPRN_MAS5 definition.
powerpc: ARCH_PFN_OFFSET should be unsigned long
powerpc: Implement dma_mmap_coherent()
powerpc/nvram: Don't overwrite oops/panic report on normal shutdown
powerpc: Restore some misc devices to our configs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
Blackfin: bitops: fix include order after little endian inclusion
Blackfin: defconfigs: update after misc devices defaulted to N
Blackfin: use more standard pr_fmt in the module loader
These two functions disappeared in commit
0c6f8a8b91
"genirq: Remove compat code"
but they still exist in qe_ic.h.
This patch renames the function to their new names.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
LKML-Reference: <20110330132504.GA31832@riccoc20.at.omicron.at>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 6845664(arm: Cleanup the irq namespace) introduces a typo
causing a build failure for the versatile platform.
[ tglx: Sorry, my bad. Have no idea how I fatfingered that ]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
LKML-Reference: <20110330060229.27397.7628.stgit@ponder>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Latest irq changes removed the need for this forcing flag, and the
definition - but missed the code that allowed it to be tweaked via
/proc. Delete accessor functions too.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Ensure the Chelsio T3/T4 network drivers and iWARP drivers are
enabled in the pseries config.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Recent upstream builds with allmodconfig fail due to lack of space
between 0x3000 and 0x6000. We have a hard block at 0x7000 but we can
spare a page by moving the STAB0 from 0x6000 to 0x8000.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit cf9efce0ce (powerpc: Account time using timebase rather
than PURR) used in_irq() to detect if the time was spent in
interrupt processing. This only catches hardirq context so if we
are in softirq context and in the idle loop we end up accounting it
as idle time. If we instead use in_interrupt() we catch both softirq
and hardirq time.
The issue was found when running a network intensive workload. top
showed the following:
0.0%us, 1.1%sy, 0.0%ni, 85.7%id, 0.0%wa, 9.9%hi, 3.3%si, 0.0%st
85.7% idle. But this was wildly different to the perf events data.
To confirm the suspicion I ran something to keep the core busy:
# yes > /dev/null &
8.2%us, 0.0%sy, 0.0%ni, 0.0%id, 0.0%wa, 10.3%hi, 81.4%si, 0.0%st
We only got 8.2% of the CPU for the userspace task and softirq has
shot up to 81.4%.
With the patch below top shows the correct stats:
0.0%us, 0.0%sy, 0.0%ni, 5.3%id, 0.0%wa, 13.3%hi, 81.3%si, 0.0%st
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If a given firmware doesn't have a token to support query-cpu-stopped-state,
its not likely to change during the lifetime of the kernel.
Only print this information once, not once per secondary thread.
While here, make the line wrap grep friendly.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To try to avoid future confusion, rename irq to hwirq when it refers
to a xics domain number instead of a linux irq number.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit 79f26c268e (powerpc:
platforms/pseries irq_data conversion) pushed irq_desc down into many
functions, dererencing the descriptor irq field as late as possible.
But it incorrectly passed a linix virtural irq number to RTAS,
resulting in the interrupt not being disabled and possibly
other bad things, such as another interrupt being disabled and/or
a checkstop.
In addition this missed the point of xics_mask_unknown_vec and
the seperation of xics_mask_real_irq from xics_mask_irq. When
xics_mask_unknown_vec is called it's because the hardware delivered an
irq source for which we have no linux irq allocated, and thefore we can
not have an irq_desc allocated.
Revert xics_mask_real_irq to its prior version, naming the argument
hwirq to highlight the difference.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These syscalls have been added recently:
name_to_handle_at
open_by_handle_at
clock_adjtime
syncfs
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
339 is the SPR number for MAS5 documented by Power ISA 2.06, and
implemented by e500mc. It is not yet used anywhere in the kernel,
so nothing should be relying on the wrong number.
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pfns are unsigned long, but MEMORY_START is phys_addr_t. This leads
to page_to_pfn() returning phys_addr_t, and thus type mismatches in a few
print statements.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is used by Alsa to mmap buffers allocated with dma_alloc_coherent()
into userspace. We need a special variant to handle machines with
non-coherent DMAs as those buffers have "special" virt addresses and
require non-cachable mappings
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For normal halt, reboot, and poweroff events, refrain from overwriting
the lnx,oops-log partition. Also, don't save the dmesg buffer on an
emergency-restart event if we've already saved it earlier in panic().
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Uwe Kleine-König reported:
while working on an defconfig (arm/mx27) I noticed that just updating
it[1] results in removing CONFIG_EEPROM_AT24=y. The reason is that
since commit
v2.6.36-5965-g5f2365d (misc devices: do not enable by default)
MISC_DEVICES isn't enabled anymore by default. So all defconfigs that
have CONFIG_SOME_SYMBOL=y (or =m) (with SOME_SYMBOL depending on
MISC_DEVICES) but not CONFIG_MISC_DEVICES=y suffer from the same
problem.
This restores those misc devices to the powerpc defconfigs.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Uwe Kleine-König
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On laptops with core i5/i7, there were reports that after resume
graphics workloads were performing poorly on a specific AP, while
the other cpu's were ok. This was observed on a 32bit kernel
specifically.
Debug showed that the PAT init was not happening on that AP
during resume and hence it contributing to the poor workload
performance on that cpu.
On this system, resume flow looked like this:
1. BP starts the resume sequence and we reinit BP's MTRR's/PAT
early on using mtrr_bp_restore()
2. Resume sequence brings all AP's online
3. Resume sequence now kicks off the MTRR reinit on all the AP's.
4. For some reason, between point 2 and 3, we moved from BP
to one of the AP's. My guess is that printk() during resume
sequence is contributing to this. We don't see similar
behavior with the 64bit kernel but there is no guarantee that
at this point the remaining resume sequence (after AP's bringup)
has to happen on BP.
5. set_mtrr() was assuming that we are still on BP and skipped the
MTRR/PAT init on that cpu (because of 1 above)
6. But we were on an AP and this led to not reprogramming PAT
on this cpu leading to bad performance.
Fix this by doing unconditional mtrr_if->set_all() in set_mtrr()
during MTRR/PAT init. This might be unnecessary if we are still
running on BP. But it is of no harm and will guarantee that after
resume, all the cpu's will be in sync with respect to the
MTRR/PAT registers.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1301438292-28370-1-git-send-email-eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Keith Packard <keithp@keithp.com>
Cc: stable@kernel.org [v2.6.32+]
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The lonely user of the internal interface was not in the coccinelle
script.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (26 commits)
mmc: SDHI should depend on SUPERH || ARCH_SHMOBILE
mmc: tmio_mmc: Move some defines into a shared header
mmc: tmio: support aggressive clock gating
mmc: tmio: fix power-mode interpretation
mmc: tmio: remove work-around for unmasked SDIO interrupts
sh: fix SDHI IO address-range
ARM: mach-shmobile: fix SDHI IO address-range
mmc: tmio: only access registers above 0xff, if available
mfd: remove now redundant sh_mobile_sdhi.h header
sh: convert boards to use linux/mmc/sh_mobile_sdhi.h
ARM: mach-shmobile: convert boards to use linux/mmc/sh_mobile_sdhi.h
mmc: tmio: convert the SDHI MMC driver from MFD to a platform driver
sh: ecovec: use the CONFIG_MMC_TMIO symbols instead of MFD
mmc: tmio: split core functionality, DMA and MFD glue
mmc: tmio: use PIO for short transfers
mmc: tmio-mmc: Improve DMA stability on sh-mobile
mmc: fix mmc_app_send_scr() for dma transfer
mmc: sdhci-esdhc: enable esdhc on imx53
mmc: sdhci-esdhc: use writel/readl as general APIs
mmc: sdhci: add the abort CMDTYPE bits definition
...
* 'frv' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-frv:
FRV: Use generic show_interrupts()
FRV: Convert genirq namespace
frv: Select GENERIC_HARDIRQS_NO_DEPRECATED
frv: Convert cpu irq_chip to new functions
frv: Convert mb93493 irq_chip to new functions
frv: Convert mb93093 irq_chip to new function
frv: Convert mb93091 irq_chip to new functions
frv: Fix typo from __do_IRQ overhaul
frv: Remove stale irq_chip.end
FRV: Do some cleanups
FRV: Missing node arg in alloc_thread_info_node() macro
NOMMU: implement access_remote_vm
NOMMU: support SMP dynamic percpu_alloc
NOMMU: percpu should use is_vmalloc_addr().
Fix section mismatch warnings:
set_phys_range_identity() is called by __init xen_set_identity(),
so also mark set_phys_range_identity() as __init.
then:
__early_alloc_p2m() is called set_phys_range_identity(), so also mark
__early_alloc_p2m() as __init.
WARNING: arch/x86/built-in.o(.text+0x7856): Section mismatch in reference from the function __early_alloc_p2m() to the function .init.text:extend_brk()
The function __early_alloc_p2m() references
the function __init extend_brk().
This is often because __early_alloc_p2m lacks a __init
annotation or the annotation of extend_brk is wrong.
WARNING: arch/x86/built-in.o(.text+0x7967): Section mismatch in reference from the function set_phys_range_identity() to the function .init.text:extend_brk()
The function set_phys_range_identity() references
the function __init extend_brk().
This is often because set_phys_range_identity lacks a __init
annotation or the annotation of extend_brk is wrong.
[v2: Per Stephen Hemming recommonedation made __early_alloc_p2m static]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Convert to new function names. Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Howells <dhowells@redhat.com>
irq_chip.end got obsolete with the removal of __do_IRQ().
irq-mb93093.c even lacks an implementation, but nobody noticed that
it's broken since commit 88d6e1 in 2006.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Howells <dhowells@redhat.com>
1. frv doesn't support SMP, remove the useless SMP bits.
2. frv has its own alloc_task_struct, so define __HAVE_ARCH_TASK_STRUCT_ALLOCATOR
(I am not sure if frv should use generic alloc_task_struct().)
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
There are two alloc_thread_info_node() macros defined (one for debugging and
one for normal). The commit that changed them most recently:
commit b6a84016bd
Author: Eric Dumazet <eric.dumazet@gmail.com>
Date: Tue Mar 22 16:30:42 2011 -0700
Subject: mm: NUMA aware alloc_thread_info_node()
didn't add the node argument into the macro argument list for the normal macro.
This results in the following error:
kernel/fork.c:267:39: error: macro "alloc_thread_info_node" passed 2 arguments, but takes just 1
kernel/fork.c: In function 'dup_task_struct':
kernel/fork.c:267: error: 'alloc_thread_info_node' undeclared (first use in this function)
kernel/fork.c:267: error: (Each undeclared identifier is reported only once
kernel/fork.c:267: error: for each function it appears in.)
Signed-off-by: David Howells <dhowells@redhat.com>
All chips converted
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <20110206192106.601290592@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <20110206192106.501651128@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <20110206192106.401266547@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <20110206192106.300303769@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <20110206192106.203431646@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Compiles way better.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <20110206192106.109992056@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
irq_chip.end got obsolete with the removal of __do_IRQ().
irq-mb93093.c even lacks an implementation, but nobody noticed that
it's broken since commit 88d6e1 in 2006.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <20110206192106.011224503@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make use of the new features in genirq:
1) Set the chip flag IRCHIP_EOI_IF_HANDLED, which ensures in the
core code that irq_eoi() is only called when the interrupt was
handled. That removes the extra status check in the callback.
2) Use the preflow handler, which is called from the fasteoi core code
before the device handler. That avoids another status check and the
open coded handler redirection.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: sparclinux@vger.kernel.org
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus. The core also
updates the LEVEL flag.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus. The core also
updates IRQ_LEVEL.
Use irq_data to get the level type information in the chip functions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus.
The new core code allows to update the type in irq_data and return
IRQ_SET_MASK_OK_NOCOPY, so the core code will not touch it, except for
setting the IRQ_LEVEL flag.
Retrieve the IRQ_LEVEL information from irq_data which avoids a
redundant sparse irq lookup as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus. The level flag is
updated in the core as well.
Use the proper accessors for setting the irq handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus.
The new core code allows to update the type in irq_data and return
IRQ_SET_MASK_OK_NOCOPY, so the core code will not touch it, except for
setting the IRQ_LEVEL flag.
Use the proper accessors for setting the irq handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core code provides the same functionality when the
IRQCHIP_EOI_IF_HANDLED flag is set for the irq chip.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus.
The new core code allows to update the type in irq_data and return
IRQ_SET_MASK_OK_NOCOPY, so the core code will not touch it, except for
setting the IRQ_LEVEL flag.
Use the proper accessors for setting the irq handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core irq_set_type() function updates the flow type when the chip
callback returns 0. It also updates irq_data, so this can be used in
irq_ack() to check for the level bit. That avoids a redundant sparse
irq lookup.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The irq chip has no irq_set_type() callback. So calling the call is
pointless. Set IRQ_LEVEL via the proper accessor.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Convert to the new function names. Scripted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: linux-parisc@vger.kernel.org
1) As promised in the comment, the core does not copy cpumask anymore
when the arch code returns -EINVAL
2) Get the per cpu information from irq_data
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: linux-parisc@vger.kernel.org
Make use of the IRQCHIP_ONOFFLINE_ENABLED flag and remove the
wrappers. Use irqd_irq_disabled() instead of desc->status, which will
go away.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: David Daney <ddaney@caviumnetworks.com>
This includes conversion to new style irq_chip functions, and
correctly enabling/disabling per-CPU interrupts.
The hardware interrupt bit to irq number mapping is now done with a
flexible map, instead of by bit twiddling the irq number.
[ tglx: Adjusted to new irq_cpu_on/offline callbacks and
__irq_set_affinity_lock ]
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Cc: ralf@linux-mips.org
LKML-Reference: <1301081931-11240-5-git-send-email-ddaney@caviumnetworks.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fabio Estevam