This commit fixes the following issues:
1. The 9th bit of buf was believed to be the LSB of divisor's
exponent, but the hardware interprets it as MSB (9th bit) of the
mantissa. The exponent is actually one bit shorter and applies
to base 4, not 2 as previously believed.
2. Loop iterations doubled the exponent instead of incrementing.
3. The exponent wasn't checked for overflow.
4. The function returned requested rate instead of actual rate.
Due to issue #2, the old code deviated from the wrong formula
described in #1 and actually yielded correct rates when divisor
was lower than 4096 by using exponents of 0, 2 or 4 base-2,
interpreted as 0, 1, 2 base-4 with the 9th mantissa bit clear.
However, at 93.75 kbaud or less the rate turned out too slow
due to #2 or too fast due to #2 and #3.
I tested this patch by sending and validating 0x00,0x01,..,0xff
to an FTDI dongle at 234, 987, 2401, 9601, 31415, 115199, 250k,
500k, 750k, 1M, 1.5M, 3M+1 baud. All rates passed.
I also used pv to check speed at some rates unsupported by FTDI:
45 (the lowest possible), 2M, 4M, 5M and 6M-1. Looked sane.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Fixes: 399aa9a75a ("USB: pl2303: use divisors for unsupported baud
rates")
Cc: stable <stable@vger.kernel.org> # v3.18
[johan: update summary ]
Signed-off-by: Johan Hovold <johan@kernel.org>
This phone is already supported by the visor driver.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Currently an enabled break state is not disabled on final close nor on
re-open and has to be disabled manually.
Fix this by disabling break on port shutdown.
Reported-by: Jari Ruusu <jariruusu@users.sourceforge.net>
Tested-by: Jari Ruusu <jariruusu@users.sourceforge.net>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use direct method for supported baud rates, otherwise use divisors.
Limit baud rate to 12 Mbaud with HX type.
This change has been tested to work with PL-2303HX at 115200, 500000,
1000000, 2000000, 2500000, 3000000 and 4000000 baud rates.
Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
This adds a new device id to the pl2303 driver for the ZTEK device.
Reported-by: Mike Chu <Mike-Chu@prolific.com.tw>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation which does not suffer
from the races involved when using the deprecated sleep_on functions.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only wake up MSR wait queue on actual modem-status changes.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up line-status handling somewhat.
Get tty-reference only when actually needed.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Declare constant device-type data as const.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new C_CMSPAR macro for consistency.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use direct baud-rate encoding rather than divisors for supported baud
rates.
This restores the way baud rates were set prior to commit 8d48fdf689
("USB: PL2303: correctly handle baudrates above 115200") which added
divisor encoding, but also switched to the new encoding method for all
baudrates above 115200.
As noted by Frank Schäfer <fschaefer.oss@googlemail.com>, baud rate 500k
was later errounously added to the supported baud-rate table although
it can only be set using divisors.
Note that the current implementation could easily be extended to support
arbitrary non-standard baud rates using divisors (e.g. by falling back
to divisors when the table lookup fails).
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add helper function for direct baud-rate encoding.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename baud-rate encoding function to match tty naming.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Encode all device-type specifics in a struct rather than testing for
device type and spreading such information throughout the driver.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add quirk for legacy devices (type 0 and 1) rather than testing on
device type throughout the driver.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge types 0 and 1, whose differences are unknown and have always been
treated the same.
Add TYPE_-prefix to both types.
Test for TYPE_01 (rather than !TYPE_HX) for legacy device quirks.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement line-status handling for Siemens phones as a quirk rather than
spreading such information all over the driver by matching on vendor and
and product ids.
Note that the SIEMENS_PRODUCT_ID_EF81, which was added after the
line-status handling for the other Siemens phones was fixed, might also
need this quirk.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant get_line_request (the read back settings are never
used).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor and add error handling to line requests.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add error handling and clean up vendor read and write functions.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use u16 rather than __u16.
Fix multi-line comment style.
Remove some comments.
Remove unnecessary whitespace and add some where appropriate.
Drop DRIVER_DESC define.
Merge and simplify multi-line error message.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus MSR wait-queue wake up from process_read_urb which never
updates the MSR flags.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant error messages on allocation failures, which have
already been logged.
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant ioctl debugging from subdrivers. The ioctl request code
has already been logged by usb-serial core.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some PL2303 devices are known to lose bytes if you change serial
settings even to the same values as before. Avoid this by comparing the
encoded settings with the previsouly used ones before configuring the
device.
The common case was fixed by commit bf5e5834bf ("pl2303: Fix mode
switching regression"), but this problem was still possible to trigger,
for instance, by using the TCSETS2-interface to repeatedly request
115201 baud, which gets mapped to 115200 and thus always triggers a
settings update.
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the CS5 setting on the PL2303 USB-to-serial devices. CS5 has a
value of 0 and the CSIZE setting has been skipped altogether by the enclosing
if. Tested on 3.11.6 and the scope shows the correct output after the fix has
been applied.
Tagged to be added to stable, because it fixes a user visible driver bug and is
simple enough to backport easily.
Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b8bdad6082.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 57ce61aad7.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 75417d9f99.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b9208c721c.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e917ba01d6.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b5c16c6a03.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 61fa8d694b.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c23bda365d.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 73b583af59.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a77a8c23e4.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 034d1527ad.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 7d26a78f62.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Prolific, several (unauthorized) cheap and less functional
clones of the PL2303HX chip are in circulation. [1]
I've had the chance to test such a cloned device and it turned out that
it doesn't support any baud rates above 115200 baud (original: 6 Mbaud)
It also doesn't support the divisior based baud rate encoding method,
so no continuous baud rate adjustment is possible.
Nevertheless, these devices have been working (unintentionally) with
the driver up to commit 61fa8d694b ("pl2303: also use the divisor based
baud rate encoding method for baud rates < 115200 with HX chips"), and
this commit broke support for them.
Fortunately, it is pretty simple to distinguish between the original
and the cloned HX chips, so I've added a check and an extra chip type
to keep the clones working.
The same check is used by the latest Prolific Windows driver, so it
should be solid.
[1] http://www.prolific.com.tw/US/ShowProduct.aspx?p_id=225&pcid=41
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver currently knows about 3 different PL2303 chip types:
The two legacy chip types type_0 and type_1 (PL2303H ?) and the HX
type.
The device distinction is currently completely based on the examination
of the USB descriptors.
During the last years, Prolific has introduced further PL2303 chips,
such as the HXD (HX rev. D), TA (which replaced the X/HX chips), SA,
RA, EA and TB variants.
Unfortunately, all these new chips are currently detected as HX chips,
because they are all using the same bMaxPacketSize0 = 0x40 value in the
USB device descriptor.
At this point it is not clear if these chips are really working with
the driver, there are just some positive indicators (like device
manufacturers claiming Linux support for these devices or commit
8d48fdf689 "correctly handle baudrates above 115200" which should only
be necessary for newer devices, ...)
For a complete support of all devices, we need to distinguish between
them, because they differ in several functional aspects, such as the
maximum supported baud rate (HXD, TB, EA: 12Mbps, HX, TA: 6Mbps,
RA: 1Mbps, SA: 115.2kbps), handshaking line support, RS422/485 and
GPIO ports support (currently not supported by the driver).
And there might be further differences that we don't know yet.
This patch improves the chip type detection by evaluating the bcdDevice
value of the device descriptor. The values are taken from the
datasheets and are safe to use because manufacturers can't change them:
3.00: X/HX, TA
4.00: HXD, EA, RA, SA
5.00: TB
The rest of the device descriptors is completely identical, so no
further distinction is possible this way.
Anyway, Prolifics "checkChipVersion.exe"-tool is definitely able to
distinguish for example between the X/HX and the TA chips, so there
must be a possibility to improve the distinction further...
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chip type distinction is getting more and more relevant and
complicating, so always print the chip type.
Printing a name string is also much better than just printing an
internal index number.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need for two else-if constructs for the type_1 chip
detection in pl2303_startup(), so merge them.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I've found some new datasheets which describe some additionally
supported standard baud rates and I've verified them with my HX
(rev. 3A) device. But adding support for individual (chip type
specific) baud rates would add a good amount of extra code (especially
when support for further chips will be added to the driver one day),
which makes no sense as long as we are not using the direct baud rate
encoding method for newer chips.
So for now, just drop a comment about these additionally supported baud
rates.
The second comment is about the baud rate differences between the two
encoding methods. In theory, we could optimize the code a bit by
comparing the resulting baud rates of both methods and selecting the
one which is closer to the requested baud rate. But that seems to be a
bit overkill, because the differences are very small and the device
likely uses the same baud rate generator for both methods so that the
resulting baud rate would be the same.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michał Pecio