The generic phy_ethtool_set_link_ksettings() function from phylib can
be used instead of in-house sh_eth_set_link_ksettings().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic phy_ethtool_get_link_ksettings() function from phylib can be
used instead of in-house sh_eth_get_link_ksettings().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_ethtool_ksettings_get() call does not modify device state or device
driver state, hence there is no need to utilize a driver specific
spinlock.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic phy_ethtool_nway_reset() function from phylib can be used
instead of in-house sh_eth_nway_reset().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to call a heavyweight phy_start_aneg() for phy
auto-negotiation by ethtool, the phy is already initialized and
link auto-negotiation is started by calling phy_start() from
sh_eth_phy_start() when a network device is opened.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change fixes sleep in atomic context bug, which is encountered
every time when link settings are changed by ethtool.
Since commit 35b5f6b1a8 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however that helper function is
called in atomic context under a grabbed spinlock, because
phy_start_aneg() is called by phy_ethtool_ksettings_set() and by
replaced phy_ethtool_sset() helpers from phylib.
Now duplex mode setting is enforced in sh_eth_adjust_link() only,
also now RX/TX is disabled when link is put down or modifications
to E-MAC registers ECMR and GECMR are expected for both cases of
checked and ignored link status pin state from E-MAC interrupt handler.
For reference the change is a partial rework of commit 1e1b812bbe
("sh_eth: fix handling of no LINK signal").
Fixes: dc19e4e5e0 ("sh: sh_eth: Add support ethtool")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 35b5f6b1a8 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however the helper function is
called in atomic context.
The bug can be reproduced by running "ethtool -r" command, the bug
is reported if CONFIG_DEBUG_ATOMIC_SLEEP build option is enabled.
Fixes: dc19e4e5e0 ("sh: sh_eth: Add support ethtool")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing 'maxp' in sh_eth_soft_swap(), the buffer length needs
to be rounded up -- that's just asking for DIV_ROUND_UP()!
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_tsu_soft_swap() is called twice by the driver, remove *inline* and
move that function from the header to the driver itself to let gcc decide
whether to expand it inline or not...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon has noticed a typo in the comment accompaining the BCULR write --
fix it and move the comment before the write (following the style of
the other comments), while at it...
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct name of the EESR bit 8 is TRO (transmit retry over), not RTO.
Note that EESIPR bit 8, TROIP remained correct...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finally, add support for the DT probing of the R-Car V3H (AKA R8A77980) --
it's the only R-Car gen3 SoC having the GEther controller -- others have
only EtherAVB...
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The R-Car V3H (AKA R8A77980) GEther controller adds the DMA burst mode bit
(NBST) in EDMR and the manual tells to always set it before doing any DMA.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The R-Car V3H (AKA R8A77980) GEther controller adds support for the RGMII
PHY interface mode as a new value for the RMII_MII register.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers have the following pattern:
if (np)
of_mdiobus_register()
else
mdiobus_register()
which the implementation of of_mdiobus_register() now takes care of.
Remove that pattern in drivers that strictly adhere to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3365711df0 ("sh_eth: WARN on access to a register not implemented
in a particular chip") added WARN_ON() to sh_eth_{read|write}() but not
to sh_eth_tsu_{read|write}(). Now that we've routed almost all TSU register
accesses (except TSU_ADR{H|L}<n> -- which are special) thru the latter
pair of accessors, it makes sense to check for the unimplemented TSU
registers as well...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no particularly good reason TSU_POST<n> registers get accessed
circumventing sh_eth_tsu_{read|write}() -- start using those, removing
(badly named) sh_eth_tsu_get_post_reg_offset(), while at it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Iff TSU registers exist on a given [G]Ether controller, they always include
the CAM entry table registers (TSU_ADR{H|L}<n>), thus the check for invalid
TSU_ADRH0 offset in __sh_eth_get_regs() is useless...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 6ded286555 ("sh_eth: Fix RX recovery on R-Car in case of RX
ring underrun") added a check for an bad RDFAR offset in sh_eth_rx(), so
that the code could work on the R-Car Ether controllers which don't have
this register (and TDFAR), then the commit 3365711df0 ("sh_eth: WARN on
access to a register not implemented in a particular chip") replaced
offset 0 with 0xffff. Adding/checking the 'no_xdfar' bit field in the
'struct sh_eth_cpu_data' instead results in less object code...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GEther controllers have CERCR/CEECR instead of CNDCR on the others.
Currently we are calling sh_eth_is_gether() in order to check for this,
however it would be simpler to check the new 'cexcr' bitfield in the
'struct sh_eth_cpu_data'; then we'd be able to remove sh_eth_is_gether()
as there would be no callers left...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RZ/A1H (R7S72100) Ether controller doesn't seem to have the TX counter
registers like TROCR/CDCR/LCCR (or at least they are still undocumented
like some TSU registers), so we bail out of sh_eth_get_stats() early in
this case. Currently we are calling sh_eth_is_rz_fast_ether() in order
to check for this, but it would be simpler to check the new 'no_tx_cntrs'
bitfield in the 'struct sh_eth_cpu_data'; then we'd be able to remove
sh_eth_is_rz_fast_ether() as there would be no callers left...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GEther-like controllers have writeable RDFAR/TDFAR, on the others
they are read-only or just absent (on R-Car). Currently we are calling
sh_eth_is_{gether|rz_fast_ether}() in order to check if these registers
can be written to, however it would be simpler to check the new 'xdfar_rw'
bitfield in the 'struct sh_eth_cpu_data'...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_get_edtrr_trns() returns the value to be written to EDTRR in order
to start TX DMA -- this value is different between the GEther-like and
the other controllers. We can replace this function (and thus get rid of
the calls to sh_eth_is_{gether|rz_fast_ether}() by it) with a new field
'edtrr_trns' in the 'struct sh_eth_cpu_data'.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_reset() performs a software reset which is implemented in a
completely different way for the GEther-like controllers vs the other
controllers due to a different layout of EDMR (and other factors) --
it therefore makes sense to convert this function to a mandatory
sh_eth_cpu_data::soft_reset() method and thus get rid of the runtime
controller type check via sh_eth_is_{gether|rz_fast_ether}().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
We have uninlined the sh_eth_{read|write}() functions introduced in the
commit 4a55530f38 ("net: sh_eth: modify the definitions of register").
Now remove *inline* from sh_eth_tsu_{read|write}() as well and move
these functions from the header to the driver itself. This saves 684
more bytes of object code (ARM gcc 4.8.5)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It appears that the single port Ether controllers having TSU (like SH7734/
R8A7740) need the same kind of treating in sh_eth_tsu_init() as R7S72100
currently has -- they also don't have the TSU registers related e.g. to
passing the frames between ports. Add the 'sh_eth_cpu_data::dual_port'
flag and use it as a new criterion for taking a "short path" in the TSU
init sequence in order to avoid writing to the non-existent registers...
Fixes: f0e81fecd4 ("net: sh_eth: Add support SH7734")
Fixes: 73a0d90730 ("net: sh_eth: add support R8A7740")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSU_QTAG0/1 registers found in the Gigabit Ether controllers actually
have the same long name as the TSU_QTAGM0/1 registers in the early Ether
controllers: Qtag Addition/Deletion Set Register (Port 0/1 to 1/0); thus
there's no need to make a difference in sh_eth_tsu_init() between those
controllers. Unfortunately, we can't just remove TSU_QTAG0/1 from the
register *enum* because that would break the ethtool register dump...
Fixes: b0ca2a21f7 ("sh_eth: Add support of SH7763 to sh_eth")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The *while* loop in this function can be turned into a normal *for* loop.
And getting rid of the single return point saves us a few more LoCs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if Wake-on-LAN is enabled, the SH-ETH device's module clock
is manually kept running during system suspend, to make sure the device
stays active.
Since commits 91c719f5ec ("soc: renesas: rcar-sysc: Keep wakeup
sources active during system suspend") and 744dddcae8 ("clk:
renesas: mstp: Keep wakeup sources active during system suspend"), this
workaround is no longer needed. Hence remove all explicit clock
handling to keep the device active.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dual-port Ether configurations always have a shared TSU to e.g. pass
the packets between those ports. With the TSU init. code gathered under
the single *if*, we now can only get the port # from 'platform_device::id'
only when we actually need it (and not recalculate it each time)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sh_eth_cpu_data::chip_reset() method always resets using ARSTR and
this register is always located at the start of the TSU register region.
Therefore, we can only call this method if we know TSU is there and thus
simplify the probing code a bit...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARSTR is always located at the start of the TSU register region, thus
using add_reg() instead of add_tsu_reg() in __sh_eth_get_regs() to dump it
causes EDMR or EDSR (depending on the register layout) to be dumped instead
of ARSTR. Use the correct condition/macro there...
Fixes: 6b4b4fead3 ("sh_eth: Implement ethtool register dump operations")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TXALCR1 offsets are incorrect in the register offset tables, most
probably due to copy&paste error. Luckily, the driver never uses this
register. :-)
Fixes: 4a55530f38 ("net: sh_eth: modify the definitions of register")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renesas SH7757 has 2 Fast and 2 Gigabit Ether controllers, while the
'sh_eth' driver can only reset and initialize TSU of the first controller
pair. Shimoda-san tried to solve that adding the 'needs_init' member to the
'struct sh_eth_plat_data', however the platform code still never sets this
flag. I think that we can infer this information from the 'devno' variable
(set to 'platform_device::id') and reset/init the Ether controller pair
only for an even 'devno'; therefore 'sh_eth_plat_data::needs_init' can be
removed...
Fixes: 150647fb2c ("net: sh_eth: change the condition of initialization")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When switching the driver to the managed device API, I managed to break
the case of a dual Ether devices sharing a single TSU: the 2nd Ether port
wouldn't probe. Iwamatsu-san has tried to fix this but his patch was buggy
and he then dropped the ball...
The solution is to limit calling devm_request_mem_region() to the first
of the two ports sharing the same TSU, so devm_ioremap_resource() can't
be used anymore for the TSU resource...
Fixes: d5e07e6921 ("sh_eth: use managed device API")
Reported-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Browsing thru the driver disassembly, I noticed that gcc was able to
figure out that the 'ndev' pointer is always non-NULL when calling
free_netdev() on the probe() method's error path and thus skip that
redundant NULL check... gcc is smart, be like gcc! :-)
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all variants of the sh_eth hardware have Gigabit
support. Unfortunately, the current driver doesn't tell the PHY about
the limited MAC capabilities. Due to this, if you have a Gigabit
capable PHY, the PHY will advertise its Gigabit capability and
establish a link at 1Gbit/s, even though the MAC doesn't support it.
In order to avoid this, we use the recently introduced
phy_set_max_speed() to tell the PHY to not advertise speed higher than
100 MBit/s.
Tested on a SH7786 platform, with a Gigabit PHY.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using NULL as argument for the DMA mapping API is bogus, as the DMA
mapping API may use information from the "struct device" to perform
the DMA mapping operation. Therefore, pass the appropriate "struct
device".
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two types of "struct device": the one representing the
physical device on its physical bus (platform, SPI, PCI, etc.), and
the one representing the logical device in its device class (net,
etc.).
The DMA mapping API expects to receive as argument a "struct device"
representing the physical device, as the "struct device" contains
information about the bus that the DMA API needs.
However, the sh_eth driver mistakenly uses the "struct device"
representing the logical device (embedded in "struct net_device")
rather than the "struct device" representing the physical device on
its bus.
This commit fixes that by adjusting all calls to the DMA mapping API.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement fallback compatibility strings for R-Car Gen 1 and 2.
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, f.e. Gen 1 and 2. But beyond that its not clear what the relationship
between IP blocks might be. For example, I believe that r8a7790 is older
than r8a7791 but that doesn't imply that the latter is a descendant of the
former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme is being adopted for
drivers for Renesas SoCs.
Note that R-Car Gen2 and RZ/G1 have many compatible IP blocks. The
approach that has been consistently taken for other IP blocks is to name
common code, compatibility strings and so on after R-Car Gen2.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename structures describing R-Car SoCs as rcar_gen[12]_*
rather than r8a77[79]x_*. This seems a little easier on the
eyes. And will make things slightly cleaner in a follow-up
patch that adds fallback-compatibility strings for these SoCs.
Note that R-Car Gen2 and RZ/G1 have many compatible IP blocks. The
approach that has been consistently taken for other IP blocks is to name
common code, compatibility strings and so on after R-Car Gen2.
Also rename sh_eth_set_rate_r8a777x as sh_eth_set_rate_rcar as
it it is used by the R-Car generations supported by the driver.
This patch should have no run-time effect and
is compile-tested only.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_device_id are not supposed to change at runtime. All functions
working with platform_device_id provided by <linux/platform_device.h>
work with const platform_device_id. So mark the non-const structs as
const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make return value void since function never return meaningfull value
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware supports the MTU to be changed and the driver it self is
somewhat prepared to support this. This patch hooks up the callbacks to
be able to change the MTU from user-space.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EPROBE_DEFER is not an error, hence printing an error message like
sh-eth ee700000.ethernet: failed to initialise MDIO
may confuse the user.
To fix this, suppress the error message in case of probe deferral.
While at it, shorten the message, and add the actual error code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO initialization failure message is printed using the network
device, before it has been registered, leading to:
(null): failed to initialise MDIO
Use the platform device instead to fix this:
sh-eth ee700000.ethernet: failed to initialise MDIO
Fixes: daacf03f0b ("sh_eth: Register MDIO bus before registering the network device")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Zapolskiy