The Nomadik variant has a few special quirks that need to be respected
to make the driver work:
- The block need to be clocked during writing of the TIMn registers
or the bus will stall.
- Special bits in the control register select how many of the output
display lines get activated.
- Special bits in the control register select how to manage the
different 565 and 5551 modes.
- There is a packed 24bit graphics mode, i.e 888 pixels can be stored
in memory is three consecutive bytes, not evenly aligned to a 32bit
word.
This patch uses the vendor data pointer from the AMBA matching mechanism
to track the quirks for this variant, and adds two hooks that variants
can use to initialize boards and panels during start-up. These will
later be used to adopt a Nomadik board profile.
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There are CLCDs connected with the pads in BGR rather than RGB
order. It really doesn't matter since the CLCD has a flag and
a bit to switch the position of the RGB and BGR components.
This is needed to put something logical into the
arm,pl11x,tft-r0g0b0-pads property of the device tree on the
Nomadik which will then be <16 8 0>.
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The device tree bindings from display-timing.txt allows us to
specify if data enable, hsync, vsync or the pixed clock should be
inverted on the way to the display. The driver does not currently
handle this so add support for those flags as it is needed for
the Versatile Sanyo LCD display.
Note that the previous behaviour was to invert the pixel clock
for all displays, so unless the pixel clock polarity is
explicitly defined in the device tree (i.e. the timings node
has the "pixelclk-active" property) we fall back to inverting
the pixel clock. This needs some extra compatibility code.
Since the timing flags have to be set up inside the struct
clcd_panel, we need to refactor the code a bit to pass around
the panel rather than just the mode.
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If the device is probed from device tree, we can support
backlight. This is used with some systems such as the
ST Microelectronics Nomadik.
We have to add HAS_IOMEM to the dependencies of CLCD since
the backlight class device will now be selected, and if it
gets selected on an arch that does not have IOMEM,
compilation will fail.
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The voltage changing code in this driver is broken and should be
removed. The driver sets a single, exact voltage on probe. Unless
there is a very good reason for this (which should be documented in
comments) constraints like this need to be set via the machine
constraints, voltage setting in a driver is expected to be used in cases
where the voltage varies at runtime.
In addition client drivers should almost never be calling
regulator_can_set_voltage(), if the device needs to set a voltage it
needs to set the voltage and the regulator core will handle the case
where the regulator is fixed voltage. If the driver can skip setting
the voltage it should just never set the voltage.
Signed-off-by: Mark Brown <broonie@kernel.org>
[tomi.valkeinen@ti.com: fix abuse in hdmi5.c too]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer. Thus the pointer can point to const data.
However the attributes do not have to be a bitfield. Instead unsigned
long will do fine:
1. This is just simpler. Both in terms of reading the code and setting
attributes. Instead of initializing local attributes on the stack
and passing pointer to it to dma_set_attr(), just set the bits.
2. It brings safeness and checking for const correctness because the
attributes are passed by value.
Semantic patches for this change (at least most of them):
virtual patch
virtual context
@r@
identifier f, attrs;
@@
f(...,
- struct dma_attrs *attrs
+ unsigned long attrs
, ...)
{
...
}
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
and
// Options: --all-includes
virtual patch
virtual context
@r@
identifier f, attrs;
type t;
@@
t f(..., struct dma_attrs *attrs);
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the DRIVER_NAME macro definition before the first usage site and
fix build error.
Link: http://lkml.kernel.org/r/20160801163937.GA28119@nazgul.tnic
Signed-off-by: Borislav Petkov <bp@suse.de>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge drm updates from Dave Airlie:
"This is the main drm pull request for 4.8.
I'm down with a cold at the moment so hopefully this isn't in too bad
a state, I finished pulling stuff last week mostly (nouveau fixes just
went in today), so only this message should be influenced by illness.
Apologies to anyone who's major feature I missed :-)
Core:
Lockless GEM BO freeing
Non-blocking atomic work
Documentation changes (rst/sphinx)
Prep for new fencing changes
Simple display helpers
Master/auth changes
Register/unregister rework
Loads of trivial patches/fixes.
New stuff:
ARM Mali display driver (not the 3D chip)
sii902x RGB->HDMI bridge
Panel:
Support for new panels
Improved backlight support
Bridge:
Convert ADV7511 to bridge driver
ADV7533 support
TC358767 (DSI/DPI to eDP) encoder chip support
i915:
BXT support enabled by default
GVT-g infrastructure
GuC command submission and fixes
BXT workarounds
SKL/BKL workarounds
Demidlayering device registration
Thundering herd fixes
Missing pci ids
Atomic updates
amdgpu/radeon:
ATPX improvements for better dGPU power control on PX systems
New power features for CZ/BR/ST
Pipelined BO moves and evictions in TTM
GPU scheduler improvements
GPU reset improvements
Overclocking on dGPUs with amdgpu
Polaris powermanagement enabled
nouveau:
GK20A/GM20B volt and clock improvements.
Initial support for GP100/GP104 GPUs, GP104 will not yet support
acceleration due to NVIDIA having not released firmware for them as of yet.
exynos:
Exynos5433 SoC with IOMMU support.
vc4:
Shader validation for branching
imx-drm:
Atomic mode setting conversion
Reworked DMFC FIFO allocation
External bridge support
analogix-dp:
RK3399 eDP support
Lots of fixes.
rockchip:
Lots of small fixes.
msm:
DT bindings cleanups
Shrinker and madvise support
ASoC HDMI codec support
tegra:
Host1x driver cleanups
SOR reworking for DP support
Runtime PM support
omapdrm:
PLL enhancements
Header refactoring
Gamma table support
arcgpu:
Simulator support
virtio-gpu:
Atomic modesetting fixes.
rcar-du:
Misc fixes.
mediatek:
MT8173 HDMI support
sti:
ASOC HDMI codec support
Minor fixes
fsl-dcu:
Suspend/resume support
Bridge support
amdkfd:
Minor fixes.
etnaviv:
Enable GPU clock gating
hisilicon:
Vblank and other fixes"
* tag 'drm-for-v4.8' of git://people.freedesktop.org/~airlied/linux: (1575 commits)
drm/nouveau/gr/nv3x: fix instobj write offsets in gr setup
drm/nouveau/acpi: fix lockup with PCIe runtime PM
drm/nouveau/acpi: check for function 0x1B before using it
drm/nouveau/acpi: return supported DSM functions
drm/nouveau/acpi: ensure matching ACPI handle and supported functions
drm/nouveau/fbcon: fix font width not divisible by 8
drm/amd/powerplay: remove enable_clock_power_gatings_tasks from initialize and resume events
drm/amd/powerplay: move clockgating to after ungating power in pp for uvd/vce
drm/amdgpu: add query device id and revision id into system info entry at CGS
drm/amdgpu: add new definition in bif header
drm/amd/powerplay: rename smum header guards
drm/amdgpu: enable UVD context buffer for older HW
drm/amdgpu: fix default UVD context size
drm/amdgpu: fix incorrect type of info_id
drm/amdgpu: make amdgpu_cgs_call_acpi_method as static
drm/amdgpu: comment out unused defaults_staturn_pro static const structure to fix the build
drm/amdgpu: enable UVD VM only on polaris
drm/amdgpu: increase timeout of IB test
drm/amdgpu: add destroy session when generate VCE destroy msg.
drm/amd: fix deadlock of job_list_lock V2
...
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
When building with "make W=1", we get a warning about an empty stub
function that does nothing but reassign its one of its arguments:
drivers/video/fbdev/core/fbmon.c: In function 'fb_edid_to_monspecs':
drivers/video/fbdev/core/fbmon.c:1497:67: error: parameter 'specs' set but not used [-Werror=unused-but-set-parameter]
We can simply make that function completely empty to avoid the warning.
This prevents a warning which everyone will see after "CFLAGS: add
-Wunused-but-set-parameter" is merged.
Link: http://lkml.kernel.org/r/20160715203229.1771162-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes the compatibility string to match with the smallest
supported chip (EP7209). Since the DT-support for this CPU is not yet
announced, this change is safe.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Copy the content of video/omapdss.h to a new (video/omapfb_dss.h) header
file and convert the omapfb drivers to use this new file.
The new header file is needed to complete the separation of omapdrm and
omapfb implementation of DSS.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Clean up the header files regarding to hdmi audio so the omap-hdmi-audio.h
file will only need to include the platform_data/omapdss.h file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Mark Brown <broonie@kernel.org>
CC: Jyri Sarha <jsarha@ti.com>
CC: Liam Girdwood <liam.r.girdwood@linux.intel.com>
The default_device is no longer used, it is a leftower from legacy. The
else if (pdata->default_device) is always going to be false.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
In legacy mode (non DT mode) support only composite connector type. The
only user for this is rx51, using composite type.
Dropping the connector_type selection via pdata will allow cleanups in
omapdss (drm vs fbdev).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
The panel is not used by any legacy board files so the legacy (pdata) boot
support can be dropped.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
The panel is not used by any legacy board files so the legacy (pdata) boot
support can be dropped.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
The panel is not used by any legacy board files so the legacy (pdata) boot
support can be dropped.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
The panel is not used by any legacy board files so the legacy (pdata) boot
support can be dropped.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
The panel is not used by any legacy board files so the legacy (pdata) boot
support can be dropped.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
The panel is not used by any legacy board files so the legacy (pdata) boot
support can be dropped.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
The panel is not used by any legacy board files so the legacy (pdata) boot
support can be dropped.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
The panel is not used by any legacy board files so the legacy (pdata) boot
support can be dropped.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
The panel is not used by any legacy board files so the legacy (pdata) boot
support can be dropped.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
The DDC scl high and low times were set to the minimum values
from the i2c specification, but the i2c specification takes into
account the rise time and fall time to calculate the frequency.
To pass HDMI certification DDC can not exceed 100kHz therefore in
a system where the rise times and fall times are negligible the high
and low times for scl need to be 10us.
Signed-off-by: Jim Lodes <jim.lodes@garmin.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The AVI infoframe R0-R3 in the 2nd data byte represents the
Active Format Aspect Ratio. It is four bits long not two bits.
This fixes that mask used to extract the bits before writing the
bits to the hardware registers.
Signed-off-by: Jim Lodes <jim.lodes@garmin.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This set of changes introduces an atomic API to the PWM subsystem. This
is influenced by the DRM atomic API that was introduced a while back,
though it is obviously a lot simpler. The fundamental idea remains the
same, though: drivers provide a single callback to implement the atomic
configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware. Many
use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are postponed
to v4.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sxT9
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes introduces an atomic API to the PWM subsystem.
This is influenced by the DRM atomic API that was introduced a while
back, though it is obviously a lot simpler. The fundamental idea
remains the same, though: drivers provide a single callback to
implement the atomic configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware.
Many use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are
postponed to v4.8"
* tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
pwm: Add information about polarity, duty cycle and period to debugfs
pwm: Switch to the atomic API
pwm: Update documentation
pwm: Add core infrastructure to allow atomic updates
pwm: Add hardware readout infrastructure
pwm: Move the enabled/disabled info into pwm_state
pwm: Introduce the pwm_state concept
pwm: Keep PWM state in sync with hardware state
ARM: Explicitly apply PWM config extracted from pwm_args
drm: i915: Explicitly apply PWM config extracted from pwm_args
input: misc: pwm-beeper: Explicitly apply PWM config extracted from pwm_args
input: misc: max8997: Explicitly apply PWM config extracted from pwm_args
backlight: lm3630a: explicitly apply PWM config extracted from pwm_args
backlight: lp855x: Explicitly apply PWM config extracted from pwm_args
backlight: lp8788: Explicitly apply PWM config extracted from pwm_args
backlight: pwm_bl: Use pwm_get_args() where appropriate
fbdev: ssd1307fb: Use pwm_get_args() where appropriate
regulator: pwm: Use pwm_get_args() where appropriate
leds: pwm: Use pwm_get_args() where appropriate
input: misc: max77693: Use pwm_get_args() where appropriate
...
Pull drm updates from Dave Airlie:
"Here's the main drm pull request for 4.7, it's been a busy one, and
I've been a bit more distracted in real life this merge window. Lots
more ARM drivers, not sure if it'll ever end. I think I've at least
one more coming the next merge window.
But changes are all over the place, support for AMD Polaris GPUs is in
here, some missing GM108 support for nouveau (found in some Lenovos),
a bunch of MST and skylake fixes.
I've also noticed a few fixes from Arnd in my inbox, that I'll try and
get in asap, but I didn't think they should hold this up.
New drivers:
- Hisilicon kirin display driver
- Mediatek MT8173 display driver
- ARC PGU - bitstreamer on Synopsys ARC SDP boards
- Allwinner A13 initial RGB output driver
- Analogix driver for DisplayPort IP found in exynos and rockchip
DRM Core:
- UAPI headers fixes and C++ safety
- DRM connector reference counting
- DisplayID mode parsing for Dell 5K monitors
- Removal of struct_mutex from drivers
- Connector registration cleanups
- MST robustness fixes
- MAINTAINERS updates
- Lockless GEM object freeing
- Generic fbdev deferred IO support
panel:
- Support for a bunch of new panels
i915:
- VBT refactoring
- PLL computation cleanups
- DSI support for BXT
- Color manager support
- More atomic patches
- GEM improvements
- GuC fw loading fixes
- DP detection fixes
- SKL GPU hang fixes
- Lots of BXT fixes
radeon/amdgpu:
- Initial Polaris support
- GPUVM/Scheduler/Clock/Power improvements
- ASYNC pageflip support
- New mesa feature support
nouveau:
- GM108 support
- Power sensor support improvements
- GR init + ucode fixes.
- Use GPU provided topology information
vmwgfx:
- Add host messaging support
gma500:
- Some cleanups and fixes
atmel:
- Bridge support
- Async atomic commit support
fsl-dcu:
- Timing controller for LCD support
- Pixel clock polarity support
rcar-du:
- Misc fixes
exynos:
- Pipeline clock support
- Exynoss4533 SoC support
- HW trigger mode support
- export HDMI_PHY clock
- DECON5433 fixes
- Use generic prime functions
- use DMA mapping APIs
rockchip:
- Lots of little fixes
vc4:
- Render node support
- Gamma ramp support
- DPI output support
msm:
- Mostly cleanups and fixes
- Conversion to generic struct fence
etnaviv:
- Fix for prime buffer handling
- Allow hangcheck to be coalesced with other wakeups
tegra:
- Gamme table size fix"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1050 commits)
drm/edid: add displayid detailed 1 timings to the modelist. (v1.1)
drm/edid: move displayid validation to it's own function.
drm/displayid: Iterate over all DisplayID blocks
drm/edid: move displayid tiled block parsing into separate function.
drm: Nuke ->vblank_disable_allowed
drm/vmwgfx: Report vmwgfx version to vmware.log
drm/vmwgfx: Add VMWare host messaging capability
drm/vmwgfx: Kill some lockdep warnings
drm/nouveau/gr/gf100-: fix race condition in fecs/gpccs ucode
drm/nouveau/core: recognise GM108 chipsets
drm/nouveau/gr/gm107-: fix touching non-existent ppcs in attrib cb setup
drm/nouveau/gr/gk104-: share implementation of ppc exception init
drm/nouveau/gr/gk104-: move rop_active_fbps init to nonctx
drm/nouveau/bios/pll: check BIT table version before trying to parse it
drm/nouveau/bios/pll: prevent oops when limits table can't be parsed
drm/nouveau/volt/gk104: round up in gk104_volt_set
drm/nouveau/fb/gm200: setup mmu debug buffer registers at init()
drm/nouveau/fb/gk20a,gm20b: setup mmu debug buffer registers at init()
drm/nouveau/fb/gf100-: allocate mmu debug buffers
drm/nouveau/fb: allow chipset-specific actions for oneinit()
...
Here's the big char and misc driver update for 4.7-rc1.
Lots of different tiny driver subsystems have updates here with new
drivers and functionality. Details in the shortlog.
All have been in linux-next with no reported issues for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0YYACgkQMUfUDdst+ynmtACeLpLLKZsy1v7WfkW92cLSOPBD
2C8AoLFPKoh55rlOJrNz3bW9ANAaOloX
=/nsL
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here's the big char and misc driver update for 4.7-rc1.
Lots of different tiny driver subsystems have updates here with new
drivers and functionality. Details in the shortlog.
All have been in linux-next with no reported issues for a while"
* tag 'char-misc-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (125 commits)
mcb: Delete num_cells variable which is not required
mcb: Fixed bar number assignment for the gdd
mcb: Replace ioremap and request_region with the devm version
mcb: Implement bus->dev.release callback
mcb: export bus information via sysfs
mcb: Correctly initialize the bus's device
mei: bus: call mei_cl_read_start under device lock
coresight: etb10: adjust read pointer only when needed
coresight: configuring ETF in FIFO mode when acting as link
coresight: tmc: implementing TMC-ETF AUX space API
coresight: moving struct cs_buffers to header file
coresight: tmc: keep track of memory width
coresight: tmc: make sysFS and Perf mode mutually exclusive
coresight: tmc: dump system memory content only when needed
coresight: tmc: adding mode of operation for link/sinks
coresight: tmc: getting rid of multiple read access
coresight: tmc: allocating memory when needed
coresight: tmc: making prepare/unprepare functions generic
coresight: tmc: splitting driver in ETB/ETF and ETR components
coresight: tmc: cleaning up header file
...
* imxfb: fix lcd power up
* small fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iHUZ
-----END PGP SIGNATURE-----
Merge tag 'fbdev-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
- imxfb: fix lcd power up
- small fixes and cleanups
* tag 'fbdev-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
fbdev: Use IS_ENABLED() instead of checking for built-in or module
efifb: Don't show the mapping VA
video: AMBA CLCD: Remove unncessary include in amba-clcd.c
fbdev: ssd1307fb: Fix charge pump setting
Documentation: fb: fix spelling mistakes
fbdev: fbmem: implement error handling in fbmem_init()
fbdev: sh_mipi_dsi: remove driver
video: fbdev: imxfb: add some error handling
video: fbdev: imxfb: fix semantic of .get_power and .set_power
video: fbdev: omap2: Remove deprecated regulator_can_change_voltage() usage
At the moment 'enum omap_dss_clk_source' is in omapdss.h, shared by
omapdrm and omapfb. We're about to improve the omapdrm clock code, so we
need to make a separate copy of the enum for each driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The PWM framework has clarified the concept of reference PWM config (the
platform dependent config retrieved from the DT or the PWM lookup table)
and real PWM state.
Use pwm_get_args() when the PWM user wants to retrieve this reference
config and not the current state.
This is part of the rework allowing the PWM framework to support
hardware readout and expose real PWM state even when the PWM has just
been requested (before the user calls pwm_config/enable/disable()).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The framebuffer mapping virtual address leaks information about the
kernel memory layout. Stop logging it.
Cc: Peter Jones <pjones@redhat.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The header file asm/sizes.h is unnecessary.
And it can also be compiled under X86 arch after the removal.
Signed-off-by: Wang Hongcheng <annie.wang@amd.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Make sure bit 4 is set for the charge pump setting. It is required according
to SSD1306 App Note.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
fbmem_init() ignores all errors, while fbmem_exit() does not
check if deallocating resources are valid.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove the sh_mipi_dsi driver as it appears to be unused since
c0bb9b3027 ("ARCH: ARM: shmobile: Remove ag5evm board support").
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
clk_prepare_enable can fail and if it does the controller must not be
considered enabled. So check for errors, properly unwind and give the
error code back to the caller.
While touching the clock code also enable the clocks in the same
direction and disable in reverse order.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
.set_power gets passed an FB_BLANK_XXX value, not a bool. So 0 signals
on; and >1 means off. The same applies for return values of .get_power.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXL7HfAAoJEHm+PkMAQRiGYe8IAJBGaPUq38EJh2YOV+AQf9v6
t/alhwB3DUE1E0zjLy7I7JJ+xDXtKjZh9fS6OFuIS8Q3RIrBteIJ/oH8TPpt7yZ/
SnP6rYPvYD6CImTyrh7+ORL/udEwJX8+YqFYAgUAq167gvpDjYj8r26VzdIaIN4/
oBbL8NrQNWfODieywYyhUoitVhwMz09zmBfLtGVks4vd2jUJk2Fdd9cOtGV5tRfk
DPndPgyQtbr8W0mKovV8sT9WkQeV5TsUr4MLgf7hjnAGYQ8+0KamkzzVVLBeBiiw
uazyrOCFkddZp+N7KbmbOmazV/yULRuLGgDjVKazoCsOaKOvoGCzrCk7daOPy6Q=
=CegX
-----END PGP SIGNATURE-----
Merge tag 'v4.6-rc7' into drm-next
Merge this back as we've built up a fair few conflicts, and I have
some newer trees to pull in.
Export fb_deferred_io_mmap so drivers can change vma->vm_page_prot.
When the framebuffer memory is allocated using dma_alloc_writecombine()
instead of vmalloc(), I get cache syncing problems on ARM.
This solves it:
static int drm_fbdev_cma_deferred_io_mmap(struct fb_info *info,
struct vm_area_struct *vma)
{
fb_deferred_io_mmap(info, vma);
vma->vm_page_prot = pgprot_writecombine(vma->vm_page_prot);
return 0;
}
Could this have been done in the core?
Drivers that don't set (struct fb_ops *)->fb_mmap, gets a call to
fb_pgprotect() at the end of the default fb_mmap implementation
(drivers/video/fbdev/core/fbmem.c). This is an architecture specific
function that on many platforms uses pgprot_writecombine(), but not on
all. And looking at some of the fb_mmap implementations, some of them
sets vm_page_prot to nocache for instance, so I think the safest bet is
to do this in the driver and not in the fbdev core. And we can't call
fb_pgprotect() from fb_deferred_io_mmap() either because we don't have
access to the file pointer that powerpc needs.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1461856717-6476-5-git-send-email-noralf@tronnes.org
This patch modifies all the callers of vmbus_mmio_allocate()
to call vmbus_mmio_free() instead of release_mem_region().
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
regulator_can_change_voltage() is deprecated and it's use is not necessary
as commit:
6a0028b3dd regulator: Deprecate regulator_can_change_voltage()
describers it clearly.
As there is no practical use of it it can be removed.
At this point the regulator_set_voltage() calls can not be removed as the
DT data need to be fixed first.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Allows the efifb driver to be built for ARM and arm64. This simply involves
updating the Kconfig dependency expression, and supplying dummy versions of
efifb_setup_from_dmi().
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1461614832-17633-25-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since efifb can only be built directly into the kernel, drop the module
specific includes and definitions. Drop some other includes we don't need
as well.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Peter Jones <pjones@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1461614832-17633-20-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The efifb quirks handling based on DMI identification of the platform is
specific to x86, so move it to x86 arch code.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Peter Jones <pjones@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1461614832-17633-19-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The change fixes a check of gpio_to_desc() return value, the function
returns either a valid pointer to struct gpio_desc or NULL, this makes
IS_ERR() check invalid and may lead to a NULL pointer dereference in
runtime.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The current compile-time check for inversed IENB/CNTL does not
work in multiplatform boots: as soon as versatile is included
in the build, the IENB/CNTL is switched and breaks graphics.
Convert this to a runtime switch.
Cc: stable@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Fixes: a29da136de ("ARM: versatile: convert to multi-platform")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
new device support in terms of LoC, but there has been some cleanup
in the core as well as the usual minor clk additions to various
drivers.
Core:
- parent tracking has been simplified
- CLK_IS_ROOT is now a no-op flag, cleaning up drivers has started
- of_clk_init() doesn't consider disabled DT nodes anymore
- clk_unregister() had an error path bug squashed
- of_clk_get_parent_count() has been fixed to only return unsigned ints
- HAVE_MACH_CLKDEV is removed now that the last arch user (ARM) is gone
New Drivers:
- NXP LPC18xx creg
- QCOM IPQ4019 GCC
- TI dm814x ADPLL
- i.MX6QP
Updates:
- Cyngus audio clks found on Broadcom iProc devices
- Non-critical fixes for BCM2385 PLLs
- Samsung exynos5433 updates for clk id errors, HDMI support,
suspend/resume simplifications
- USB, CAN, LVDS, and FCP clks on shmobile devices
- sunxi got support for more clks on new SoCs and went through a minor
refactoring/rewrite to use a simpler factor clk construct
- rockchip added some more clk ids and added suport for fraction dividers
- QCOM GDSCs in msm8996
- A new devm helper to make adding custom actions simpler (acked by Greg)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bZFY
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The clk changes for this release cycle are mostly dominated by new
device support in terms of LoC, but there has been some cleanup in the
core as well as the usual minor clk additions to various drivers.
Core:
- parent tracking has been simplified
- CLK_IS_ROOT is now a no-op flag, cleaning up drivers has started
- of_clk_init() doesn't consider disabled DT nodes anymore
- clk_unregister() had an error path bug squashed
- of_clk_get_parent_count() has been fixed to only return unsigned ints
- HAVE_MACH_CLKDEV is removed now that the last arch user (ARM) is gone
New Drivers:
- NXP LPC18xx creg
- QCOM IPQ4019 GCC
- TI dm814x ADPLL
- i.MX6QP
Updates:
- Cyngus audio clks found on Broadcom iProc devices
- Non-critical fixes for BCM2385 PLLs
- Samsung exynos5433 updates for clk id errors, HDMI support,
suspend/resume simplifications
- USB, CAN, LVDS, and FCP clks on shmobile devices
- sunxi got support for more clks on new SoCs and went through a
minor refactoring/rewrite to use a simpler factor clk construct
- rockchip added some more clk ids and added suport for fraction
dividers
- QCOM GDSCs in msm8996
- A new devm helper to make adding custom actions simpler (acked by Greg)"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (197 commits)
clk: bcm2835: fix check of error code returned by devm_ioremap_resource()
clk: renesas: div6: use RENESAS for #define
clk: renesas: Rename header file renesas.h
clk: max77{686,802}: Remove CLK_IS_ROOT
clk: versatile: Remove CLK_IS_ROOT
clk: sunxi: Remove use of variable length array
clk: fixed-rate: Remove CLK_IS_ROOT
clk: qcom: Remove CLK_IS_ROOT
doc: dt: add documentation for lpc1850-creg-clk driver
clk: add lpc18xx creg clk driver
clk: lpc32xx: fix compilation warning
clk: xgene: Add missing parenthesis when clearing divider value
clk: mb86s7x: Remove CLK_IS_ROOT
clk: x86: Remove clkdev.h and clk.h includes
clk: x86: Remove CLK_IS_ROOT
clk: mvebu: Remove CLK_IS_ROOT
clk: renesas: move drivers to renesas directory
clk: si5{14,351,70}: Remove CLK_IS_ROOT
clk: scpi: Remove CLK_IS_ROOT
clk: s2mps11: Remove CLK_IS_ROOT
...
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.6 kernel.
Overall the coolest thing here for me is the nouveau maxwell signed
firmware support from NVidia, it's taken a long while to extract this
from them.
I also wish the ARM vendors just designed one set of display IP, ARM
display block proliferation is definitely increasing.
Core:
- drm_event cleanups
- Internal API cleanup making mode_fixup optional.
- Apple GMUX vga switcheroo support.
- DP AUX testing interface
Panel:
- Refactoring of DSI core for use over more transports.
New driver:
- ARM hdlcd driver
i915:
- FBC/PSR (framebuffer compression, panel self refresh) enabled by default.
- Ongoing atomic display support work
- Ongoing runtime PM work
- Pixel clock limit checks
- VBT DSI description support
- GEM fixes
- GuC firmware scheduler enhancements
amdkfd:
- Deferred probing fixes to avoid make file or link ordering.
amdgpu/radeon:
- ACP support for i2s audio support.
- Command Submission/GPU scheduler/GPUVM optimisations
- Initial GPU reset support for amdgpu
vmwgfx:
- Support for DX10 gen mipmaps
- Pageflipping and other fixes.
exynos:
- Exynos5420 SoC support for FIMD
- Exynos5422 SoC support for MIPI-DSI
nouveau:
- GM20x secure boot support - adds acceleration for Maxwell GPUs.
- GM200 support
- GM20B clock driver support
- Power sensors work
etnaviv:
- Correctness fixes for GPU cache flushing
- Better support for i.MX6 systems.
imx-drm:
- VBlank IRQ support
- Fence support
- OF endpoint support
msm:
- HDMI support for 8996 (snapdragon 820)
- Adreno 430 support
- Timestamp queries support
virtio-gpu:
- Fixes for Android support.
rockchip:
- Add support for Innosilicion HDMI
rcar-du:
- Support for 4 crtcs
- R8A7795 support
- RCar Gen 3 support
omapdrm:
- HDMI interlace output support
- dma-buf import support
- Refactoring to remove a lot of legacy code.
tilcdc:
- Rewrite of pageflipping code
- dma-buf support
- pinctrl support
vc4:
- HDMI modesetting bug fixes
- Significant 3D performance improvement.
fsl-dcu (FreeScale):
- Lots of fixes
tegra:
- Two small fixes
sti:
- Atomic support for planes
- Improved HDMI support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1063 commits)
drm/amdgpu: release_pages requires linux/pagemap.h
drm/sti: restore mode_fixup callback
drm/amdgpu/gfx7: add MTYPE definition
drm/amdgpu: removing BO_VAs shouldn't be interruptible
drm/amd/powerplay: show uvd/vce power gate enablement for tonga.
drm/amd/powerplay: show uvd/vce power gate info for fiji
drm/amdgpu: use sched fence if possible
drm/amdgpu: move ib.fence to job.fence
drm/amdgpu: give a fence param to ib_free
drm/amdgpu: include the right version of gmc header files for iceland
drm/radeon: fix indentation.
drm/amd/powerplay: add uvd/vce dpm enabling flag to fix the performance issue for CZ
drm/amdgpu: switch back to 32bit hw fences v2
drm/amdgpu: remove amdgpu_fence_is_signaled
drm/amdgpu: drop the extra fence range check v2
drm/amdgpu: signal fences directly in amdgpu_fence_process
drm/amdgpu: cleanup amdgpu_fence_wait_empty v2
drm/amdgpu: keep all fences in an RCU protected array v2
drm/amdgpu: add number of hardware submissions to amdgpu_fence_driver_init_ring
drm/amdgpu: RCU protected amd_sched_fence_release
...
Pull x86 protection key support from Ingo Molnar:
"This tree adds support for a new memory protection hardware feature
that is available in upcoming Intel CPUs: 'protection keys' (pkeys).
There's a background article at LWN.net:
https://lwn.net/Articles/643797/
The gist is that protection keys allow the encoding of
user-controllable permission masks in the pte. So instead of having a
fixed protection mask in the pte (which needs a system call to change
and works on a per page basis), the user can map a (handful of)
protection mask variants and can change the masks runtime relatively
cheaply, without having to change every single page in the affected
virtual memory range.
This allows the dynamic switching of the protection bits of large
amounts of virtual memory, via user-space instructions. It also
allows more precise control of MMU permission bits: for example the
executable bit is separate from the read bit (see more about that
below).
This tree adds the MM infrastructure and low level x86 glue needed for
that, plus it adds a high level API to make use of protection keys -
if a user-space application calls:
mmap(..., PROT_EXEC);
or
mprotect(ptr, sz, PROT_EXEC);
(note PROT_EXEC-only, without PROT_READ/WRITE), the kernel will notice
this special case, and will set a special protection key on this
memory range. It also sets the appropriate bits in the Protection
Keys User Rights (PKRU) register so that the memory becomes unreadable
and unwritable.
So using protection keys the kernel is able to implement 'true'
PROT_EXEC on x86 CPUs: without protection keys PROT_EXEC implies
PROT_READ as well. Unreadable executable mappings have security
advantages: they cannot be read via information leaks to figure out
ASLR details, nor can they be scanned for ROP gadgets - and they
cannot be used by exploits for data purposes either.
We know about no user-space code that relies on pure PROT_EXEC
mappings today, but binary loaders could start making use of this new
feature to map binaries and libraries in a more secure fashion.
There is other pending pkeys work that offers more high level system
call APIs to manage protection keys - but those are not part of this
pull request.
Right now there's a Kconfig that controls this feature
(CONFIG_X86_INTEL_MEMORY_PROTECTION_KEYS) that is default enabled
(like most x86 CPU feature enablement code that has no runtime
overhead), but it's not user-configurable at the moment. If there's
any serious problem with this then we can make it configurable and/or
flip the default"
* 'mm-pkeys-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (38 commits)
x86/mm/pkeys: Fix mismerge of protection keys CPUID bits
mm/pkeys: Fix siginfo ABI breakage caused by new u64 field
x86/mm/pkeys: Fix access_error() denial of writes to write-only VMA
mm/core, x86/mm/pkeys: Add execute-only protection keys support
x86/mm/pkeys: Create an x86 arch_calc_vm_prot_bits() for VMA flags
x86/mm/pkeys: Allow kernel to modify user pkey rights register
x86/fpu: Allow setting of XSAVE state
x86/mm: Factor out LDT init from context init
mm/core, x86/mm/pkeys: Add arch_validate_pkey()
mm/core, arch, powerpc: Pass a protection key in to calc_vm_flag_bits()
x86/mm/pkeys: Actually enable Memory Protection Keys in the CPU
x86/mm/pkeys: Add Kconfig prompt to existing config option
x86/mm/pkeys: Dump pkey from VMA in /proc/pid/smaps
x86/mm/pkeys: Dump PKRU with other kernel registers
mm/core, x86/mm/pkeys: Differentiate instruction fetches
x86/mm/pkeys: Optimize fault handling in access_error()
mm/core: Do not enforce PKEY permissions on remote mm access
um, pkeys: Add UML arch_*_access_permitted() methods
mm/gup, x86/mm/pkeys: Check VMAs and PTEs for protection keys
x86/mm/gup: Simplify get_user_pages() PTE bit handling
...
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model. We now finally make GPIO chips
devices. The gpio_chip will create a gpio_device which contains
a struct device, and this gpio_device struct is kept private.
Anything that needs to be kept private from the rest of the kernel
will gradually be moved over to the gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step
of a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices. We can now discover GPIOs properly from
userspace. We still have not come up with a way to actually *use*
GPIOs from userspace.
- To encourage people to use the character device for the future,
we have it always-enabled when using GPIO. The old sysfs ABI is
still opt-in (and can be used in parallel), but is marked as
deprecated. We will keep it around for the foreseeable future,
but it will not be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes. This dates back to when GPIO was an opt-in feature and
no shared library even existed: just a header file with proper
prototypes was provided and all semantics were up to the arch to
implement. These patches make the GPIO chip even more a proper
device and cleans out leftovers of the old in-kernel API here
and there. Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going
on, but we now return sane values in the vast majority of drivers
and the errorpath is sanitized. Some patches for powerpc, blackfin
and unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected
to SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9AJ4
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel v4.6. There is quite a
lot of interesting stuff going on.
The patches to other subsystems and arch-wide are ACKed as far as
possible, though I consider things like per-arch <asm/gpio.h> as
essentially a part of the GPIO subsystem so it should not be needed.
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model.
We now finally make GPIO chips devices. The gpio_chip will create
a gpio_device which contains a struct device, and this gpio_device
struct is kept private. Anything that needs to be kept private
from the rest of the kernel will gradually be moved over to the
gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step of
a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices.
We can now discover GPIOs properly from userspace. We still have
not come up with a way to actually *use* GPIOs from userspace.
- To encourage people to use the character device for the future, we
have it always-enabled when using GPIO. The old sysfs ABI is still
opt-in (and can be used in parallel), but is marked as deprecated.
We will keep it around for the foreseeable future, but it will not
be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes.
This dates back to when GPIO was an opt-in feature and no shared
library even existed: just a header file with proper prototypes was
provided and all semantics were up to the arch to implement. These
patches make the GPIO chip even more a proper device and cleans out
leftovers of the old in-kernel API here and there.
Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going on,
but we now return sane values in the vast majority of drivers and
the errorpath is sanitized. Some patches for powerpc, blackfin and
unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected to
SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller"
* tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (194 commits)
Revert "Share upstreaming patches"
gpio: mcp23s08: Fix clearing of interrupt.
gpiolib: Fix comment referring to gpio_*() in gpiod_*()
gpio: pca953x: Fix pca953x_gpio_set_multiple() on 64-bit
gpio: xgene: Fix kconfig for standby GIPO contoller
gpio: Add generic serializer DT binding
gpio: uapi: use 0xB4 as ioctl() major
gpio: tps65912: fix bad merge
Revert "gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free"
gpio: omap: drop dev field from gpio_bank structure
gpio: mpc8xxx: Slightly update the code for better readability
gpio: mpc8xxx: Remove *read_reg and *write_reg from struct mpc8xxx_gpio_chip
gpio: mpc8xxx: Fixup setting gpio direction output
gpio: mcp23s08: Add support for mcp23s18
dt-bindings: gpio: altera: Fix altr,interrupt-type property
gpio: add driver for MEN 16Z127 GPIO controller
gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free
gpio: timberdale: Switch to devm_ioremap_resource()
gpio: ts4800: Add IMX51 dependency
gpiolib: rewrite gpiodev_add_to_list
...
The Xen framebuffer driver selects the xen keyboard driver, so the latter
will be built-in if XEN_FBDEV_FRONTEND=y. However, when CONFIG_INPUT
is a loadable module, this configuration cannot work. On mainline kernels,
the symbol will be enabled but not used, while in combination with
a patch I have to detect such useless configurations, we get the
expected link failure:
drivers/input/built-in.o: In function `xenkbd_remove':
xen-kbdfront.c:(.text+0x2f0): undefined reference to `input_unregister_device'
xen-kbdfront.c:(.text+0x30e): undefined reference to `input_unregister_device'
This removes the extra "select", as it just causes more trouble than
it helps. In theory, some defconfig file might break if it has
XEN_FBDEV_FRONTEND in it but not INPUT_XEN_KBDDEV_FRONTEND. The Kconfig
fragment we ship in the kernel (kernel/configs/xen.config) however
already enables both, and anyone using an old .config file would
keep having both enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: David Vrabel <david.vrabel@citrix.com>
Fixes: 36c1132e34 ("xen kconfig: fix select INPUT_XEN_KBDDEV_FRONTEND")
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Rename dma_*_writecombine() to dma_*_wc(), so that the naming
is coherent across the various write-combining APIs. Keep the
old names for compatibility for a while, these can be removed
at a later time. A guard is left to enable backporting of the
rename, and later remove of the old mapping defines seemlessly.
Build tested successfully with allmodconfig.
The following Coccinelle SmPL patch was used for this simple
transformation:
@ rename_dma_alloc_writecombine @
expression dev, size, dma_addr, gfp;
@@
-dma_alloc_writecombine(dev, size, dma_addr, gfp)
+dma_alloc_wc(dev, size, dma_addr, gfp)
@ rename_dma_free_writecombine @
expression dev, size, cpu_addr, dma_addr;
@@
-dma_free_writecombine(dev, size, cpu_addr, dma_addr)
+dma_free_wc(dev, size, cpu_addr, dma_addr)
@ rename_dma_mmap_writecombine @
expression dev, vma, cpu_addr, dma_addr, size;
@@
-dma_mmap_writecombine(dev, vma, cpu_addr, dma_addr, size)
+dma_mmap_wc(dev, vma, cpu_addr, dma_addr, size)
We also keep the old names as compatibility helpers, and
guard against their definition to make backporting easier.
Generated-by: Coccinelle SmPL
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: airlied@linux.ie
Cc: akpm@linux-foundation.org
Cc: benh@kernel.crashing.org
Cc: bhelgaas@google.com
Cc: bp@suse.de
Cc: dan.j.williams@intel.com
Cc: daniel.vetter@ffwll.ch
Cc: dhowells@redhat.com
Cc: julia.lawall@lip6.fr
Cc: konrad.wilk@oracle.com
Cc: linux-fbdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: luto@amacapital.net
Cc: mst@redhat.com
Cc: tomi.valkeinen@ti.com
Cc: toshi.kani@hp.com
Cc: vinod.koul@intel.com
Cc: xen-devel@lists.xensource.com
Link: http://lkml.kernel.org/r/1453516462-4844-1-git-send-email-mcgrof@do-not-panic.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch continues the work to create private versions of the
omapdss.h header for omapdrm and omapfb. This one moves the dss_mgr_*
function declarations.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch continues the work to create private versions of the
omapdss.h header for omapdrm and omapfb. This one moves 'struct dss_mgr_ops'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdrm and omapfb still share the same include/video/omapdss.h. We need
to change that so that we can proceed with omapdrm work.
However, it's not trivial to make separate omapfb and omapdrm versions
of omapdss.h, as that file is also included in other places like arch
code, audio code and omap_vout code. So we'll do it piece by piece.
This patch makes private versions of all the dispc function declarations
that are in omapdss.h. For omapdrm we create a new file,
drivers/gpu/drm/omapdrm/dss/omapdss.h, which will contain headers meant
to be visible outside omapdss.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The variables modeflag and resinfo were only assigned some value but
were never used.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The Kconfig currently controlling compilation of this code is:
config FB_XVR2500
bool "Sun XVR-2500 3DLABS Wildcat support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
We don't replace module.h with init.h since the file already has that.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The Kconfig currently controlling compilation of this code is:
config FB_XVR1000
bool "Sun XVR-1000 support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
We don't replace module.h with init.h since the file already has that.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The Kconfig currently controlling compilation of this code is:
config FB_XVR500
bool "Sun XVR-500 3DLABS Wildcat support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't replace module.h with init.h since the file already has that.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The s6e8ax0 driver has a dependency on BACKLIGHT_CLASS_DEVICE,
which can be configured as a loadable module, so we have to
make the driver a tristate symbol as well, to avoid this error:
drivers/built-in.o: In function `s6e8ax0_probe':
:(.text+0x23a48): undefined reference to `devm_backlight_device_register'
This also means we get another error from a missing export, which
this fixes as well:
ERROR: "exynos_mipi_dsi_register_lcd_driver" [drivers/video/fbdev/exynos/s6e8ax0.ko] undefined!
The drivers are all written to be loadable modules already,
except the Kconfig options for that are missing, which makes
the patch really easy.
Finally, the EXYNOS_VIDEO option is turned into tristate as well
for good measure, as all framebuffer drivers should be configurable
as modules, though this change is not strictly necessary.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit 028cd86b79 ("video: da8xx-fb: fix the polarities of the
hsync/vsync pulse") fixes polarities of HSYNC/VSYNC pulse but
forgot to update known_lcd_panels[] which had sync values
according to old logic. This breaks LCD at least on DA850 EVM.
This patch fixes this issue and I have tested this for panel
"Sharp_LK043T1DG01" using DA850 EVM board.
Fixes: 028cd86b79 ("video: da8xx-fb: fix the polarities of the hsync/vsync pulse")
Signed-off-by: Sushaanth Srirangapathi <sushaanth.s@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The check for < 0 is impossible now that
of_clk_get_parent_count() returns an unsigned int. Simplify the
code and update the types.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: <linux-fbdev@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The fb_rotate method in struct fb_ops is never actually invoked, and
it's been that way in the entire history of git (in fact, the last
occurrence of the string '->fb_rotate' vanished over 10 years ago,
with b4d8aea6d6, and that merely tested whether the callback
existed). So remove some dead code and make struct fb_obs a little
smaller.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The Bt431 cursor generator supports simultaneous generation of a 64 x 64
and a cross hair cursor in which the cursor format control bit (bit D4)
of the command register "specifies whether the contents of the cursor
RAM are to be logically exclusive-ORed (logical zero) or ORed (logical
one) with the cross hair cursor". Rename the relevant macro accordingly.
References:
[1] "Bt431 Monolithic CMOS 64 x 64 Pixel Cursor Generator", Brooktree
Corporation, Document Number: L431001, Rev. J
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the address autoincrement feature when accessing successive palette
entries and also skip loading a palette address in overlay register
assesses which do not use that address. Provide a red/green/blue
register sequencer reset helper for use in overlay register assesses
where the state of the sequencer is not known.
References:
[1] "Bt454 Bt455 170 MHz Monolithic CMOS 16 Color Palette RAMDAC",
Brooktree Corporation, Document Number: L454001, Rev. I
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The Bt455 is a greyscale RAMDAC, using the green color palette entries
only while still providing registers for the red and blue components,
all the three of which have to be loaded on palette updates. Chip
documentation [1] mandates that the unused red and blue registers are
written with 0.
Therefore update code to follow this requirement and given that it makes
the red and blue components unusable remove them from internal API calls
altogether.
References:
[1] "Bt454 Bt455 170 MHz Monolithic CMOS 16 Color Palette RAMDAC",
Brooktree Corporation, Document Number: L454001, Rev. I
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The board uses hardwired timings compatible with 72Hz DEC VR319-DA and
VRM17-AA monitors, according to the board owner's manual[1]. These
timings are accordingly taken from the VR319 manual[2].
References:
[1] "The Monochrome Frame Buffer TURBOchannel Module", Digital Equipment
Corporation, Order Number: EK-MFBOM-TC-001, December 1991
[2] "Installing and Using the VR319 Monochrome Monitor", Digital
Equipment Corporation, Order Number: EK-VR319-IN-001, First Edition,
January 1990, Table 6-1 "Video Timing--1280 x 1024 Resolution"
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With the current TURBOchannel API support is automagical.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Rework the driver to use the current frambuffer and TURBOchannel APIs,
including proper resource management and using the new framework for
hardware cursor support.
NB two Bt431 cursor generators are included onboard, both responding at
the same TURBOchannel bus addresses and with their host data buses wired
to byte lanes #0 and #1 respectively of the 32-bit bus. Therefore both
can be accessed simultaneously with 16-bit data transfers. Cursor
outputs of the chip wired to lane #0 drive the respective overlay select
inputs of the Bt455 RAMDAC, whereas cursor outputs of the chip wired to
lane #1 drive the respective P3 pixel select inputs of the RAMDAC.
So 5 (out of 17) Bt455 color registers are usable with this board:
palette entries #0 and #1 for frame buffer pixel data driven while
neither cursor generator is active, palette entries #8 and #9 for frame
buffer pixel data driven while cursor generator #1 is active only and
the overlay entry while cursor generator #0 is active.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
According to the board specification[1] the width of the vertical sync
front porch is 12 pixels or the same as the width of the horizontal sync
front porch. This in turn means the size of the lower margin is 0,
because the vertical sync starts as soon as the start of the horizontal
sync terminates the last line.
References:
[1] "PMAG-BA TURBOchannel Color Frame Buffer Functional Specification",
Revision 1.2, Workstation Systems Engineering, Digital Equipment
Corporation, August 27, 1990, Table 3-5: "Video Timing"
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We were not checking the return value of platform_device_add_data()
which can fail.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As the function name already indicates that get_opt_bool() parses
for a bool. It is not a surprise that compiler is complaining
about it when -Werror=incompatible-pointer-types is used:
drivers/video/fbdev/intelfb/intelfbdrv.c: In function ‘intelfb_setup’:
drivers/video/fbdev/intelfb/intelfbdrv.c:353:39: error: passing argument 3 of ‘get_opt_bool’ from incompatible pointer type [-Werror=incompatible-pointer-types]
if (get_opt_bool(this_opt, "accel", &accel))
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
par->metromem_cmd->args[] is an array of 31 elements of size u16. Here
we have initialized the first "i" elements and want to set the rest to
zero.
The issue here is that ARRAY_SIZE(par->metromem_cmd->args) is 31 and not
32 as in the original code. It means that we set ->csum to zero, but
that is harmless because we immediately set it to the correct value on
the next line.
Still, the buffer overflow upsets static checkers so let's correct the
math.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We will soon modify the vanilla get_user_pages() so it can no
longer be used on mm/tasks other than 'current/current->mm',
which is by far the most common way it is called. For now,
we allow the old-style calls, but warn when they are used.
(implemented in previous patch)
This patch switches all callers of:
get_user_pages()
get_user_pages_unlocked()
get_user_pages_locked()
to stop passing tsk/mm so they will no longer see the warnings.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: jack@suse.cz
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20160212210156.113E9407@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Most arches have an asm/gpio.h that merely includes linux/gpio.h. The
others select ARCH_HAVE_CUSTOM_GPIO_H, and when that's selected,
linux/gpio.h includes asm/gpio.h.
Therefore, code should include linux/gpio.h instead of including asm/gpio.h
directly.
Remove includes of asm/gpio.h, adding an include of linux/gpio.h when
necessary.
This is a follow-on to 7563bbf89d ("gpiolib/arches: Centralise
bolierplate asm/gpio.h").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drivers should include asm/pci-bridge.h only when they need the arch-
specific things provided there. Outside of the arch/ directories, the only
drivers that actually need things provided by asm/pci-bridge.h are the
powerpc RPA hotplug drivers in drivers/pci/hotplug/rpa*.
Remove the includes of asm/pci-bridge.h from the other drivers, adding an
include of linux/pci.h if necessary.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently when we boot the kernel on a mx25pdk the LCDC controller
does not show the Linux logo on boot.
This problem is well explained by Sascha Hauer:
"Unfortunately this LCD controller does not have an enable bit. The
controller starts directly when the clocks are enabled. If the clocks
are enabled when the controller is not yet programmed with proper
register values then it just goes into some undefined state. What I
suspect is that the clocks already were enabled before driver probe,
presumably by the bootloader, so the controller is already in undefined
state when entering Linux. Now by dis/enabling the ipg clock you
effectively reset the controller. Since you have programmed it with
valid register values in the mean time it starts working after this
reset."
So do as suggested and force a reset of the LCDC hardware by
enabling and disabling the IPG clock.
With this change the Linux logo can be seen on boot on a mx25pdk.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
resource_size_t cannot be printed using the %x format string
when we it is defined as u64:
drivers/video/fbdev/mmp/hw/mmp_ctrl.c: In function 'mmphw_probe':
drivers/video/fbdev/mmp/hw/mmp_ctrl.c:506:22: error: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t {aka long long unsigned int}' [-Werror=format=]
dev_err(ctrl->dev, "%s: res %x - %x map failed\n", __func__,
^
drivers/video/fbdev/mmp/hw/mmp_ctrl.c:506:22: error: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'resource_size_t {aka long long unsigned int}' [-Werror=format=]
This changes the format string to %pR, which is interpreted
by the printk implementation to pretty-print a resource
structure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The probe function correct passes a dma_addr_t pointer into
dma_alloc_coherent(), but has a cast to resource_size_t, which
might be different from dma_addr_t:
drivers/video/fbdev/da8xx-fb.c: In function 'fb_probe':
drivers/video/fbdev/da8xx-fb.c:1431:10: error: passing argument 3 of 'dma_alloc_coherent' from incompatible pointer type [-Werror=incompatible-pointer-types]
This removes the cast, which avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The s6e8ax0 suspend/resume functions are hidden inside of an #ifdef
when CONFIG_PM is set to avoid unused function warnings, but they
call some other functions that nothing else calls, and we get warnings
about those:
drivers/video/fbdev/exynos/s6e8ax0.c:449:13: error: 's6e8ax0_sleep_in' defined but not used [-Werror=unused-function]
drivers/video/fbdev/exynos/s6e8ax0.c:485:13: error: 's6e8ax0_display_off' defined but not used [-Werror=unused-function]
This marks the PM functions as __maybe_unused so the compiler can
silently drop them when they are not referenced.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
According to the ocfb documentation:
Fix tgdel HW param should be left margin, not right.
Fix tvdel HW param should upper margin, not lower.
This seems to fix lock issues on certain monitors (tested on a
slightly customized IP, but the FPGA guy said that it should
be the same wrt this changes).
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Acked-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
parallel to mutex_{lock,unlock,trylock,is_locked,lock_nested},
inode_foo(inode) being mutex_foo(&inode->i_mutex).
Please, use those for access to ->i_mutex; over the coming cycle
->i_mutex will become rwsem, with ->lookup() done with it held
only shared.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* pxafb: device-tree support
* An unsafe kernel parameter 'lockless_register_fb' for debugging problems
happening while inside the console lock
* Small miscellaneous fixes & cleanups
* omapdss: add writeback support functions
* Separation of omapfb and omapdrm (see below)
About the separation of omapfb and omapdrm, see
http://permalink.gmane.org/gmane.comp.video.dri.devel/143151 for longer story.
The short version:
omapfb and omapdrm have shared low level drivers (omapdss and panel drivers),
making further development of omapdrm difficult. After these patches omapfb and
omapdrm have their own versions of the drivers, which are more or less
direct copies for now but will diverge soon.
This also means that omapfb (everything under drivers/video/fbdev/omap2/) is
now in maintenance mode, and all new development will be done for omapdrm
(drivers/gpu/drm/omapdrm/).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Nrji
-----END PGP SIGNATURE-----
Merge tag 'fbdev-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
"Summary:
- pxafb: device-tree support
- An unsafe kernel parameter 'lockless_register_fb' for debugging
problems happening while inside the console lock
- Small miscellaneous fixes & cleanups
- omapdss: add writeback support functions
- Separation of omapfb and omapdrm (see below)
About the separation of omapfb and omapdrm, see
http://permalink.gmane.org/gmane.comp.video.dri.devel/143151
for longer story. The short version:
omapfb and omapdrm have shared low level drivers (omapdss and panel
drivers), making further development of omapdrm difficult. After
these patches omapfb and omapdrm have their own versions of the
drivers, which are more or less direct copies for now but will diverge
soon.
This also means that omapfb (everything under drivers/video/fbdev/omap2/)
is now in maintenance mode, and all new development will be done for
omapdrm (drivers/gpu/drm/omapdrm/)"
* tag 'fbdev-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (49 commits)
video: fbdev: pxafb: fix out of memory error path
drm/omap: make omapdrm select OMAP2_DSS
drm/omap: move omapdss & displays under omapdrm
omapfb: move vrfb into omapfb
omapfb: take omapfb's private omapdss into use
omapfb/displays: change CONFIG_DISPLAY_* to CONFIG_FB_OMAP2_*
omapfb/dss: change CONFIG_OMAP* to CONFIG_FB_OMAP*
omapdss: remove CONFIG_OMAP2_DSS_VENC from omapdss.h
omapfb: copy omapdss & displays for omapfb
omapfb: allow compilation only if DRM_OMAP is disabled
fbdev: omap2: panel-dpi: simplify gpio setting
fbdev: omap2: panel-dpi: in .disable first disable backlight then display
OMAPDSS: DSS: fix a warning message
video: omapdss: delete unneeded of_node_put
OMAPDSS: DISPC: Remove boolean comparisons
OMAPDSS: DSI: cleanup DSI_IRQ_ERROR_MASK define
OMAPDSS: remove extra out == NULL checks
OMAPDSS: change internal dispc functions to static
OMAPDSS: make a two dss feat funcs internal to omapdss
OMAPDSS: remove extra EXPORT_SYMBOLs
...
As seen by Julia, the initial allocation memory is not checked anymore
after commit "video: fbdev: pxafb: initial devicetree conversion".
Introduce back the removed test.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that omapfb has its own copy of omapdss and display drivers, we can
move omapdss and display drivers which omapdrm uses to omapdrm's
directory.
We also need to change the main drm Makefile so that omapdrm directory
is always entered, because omapdss has a file that can't be built as a
module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
VRFB is only used by omapfb, so we can move it under omapfb's directory.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
omapfb's private copy of omapdss is now ready to be used.
This patch makes omapfb use its private omapdss and display drivers, and
also makes omap_vout (which uses omapfb) to depend on omapfb.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
We need to change the config symbols of omapfb's private copy of the
panel and encoder drivers so that we won't have config symbol conflicts.
This patch changes the symbols from the panel and encoder drivers using
simple replacement of DISPLAY_* to FB_OMAP2*.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
We need to change the config symbols of omapfb's private copy of
omapdss so that we won't have config symbol conflicts.
This patch changes the symbols from omapdss using simple replacement of
CONFIG_OMAP* to CONFIG_FB_OMAP*.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
This patch makes a copy of the omapdss driver and the omap panel &
encoder drivers for omapfb. The purpose is to separate omapdrm and
omapfb drivers from each other.
Note that this patch only does a direct copy of the files without any
other modifications. The files are not yet used.
The original files are in:
drivers/video/fbdev/omap2/dss/
drivers/video/fbdev/omap2/displays-new/
Here's a more detailed explanation about this and the following patches,
from the introduction mail of the patch series:
A short background on the current status. We have the following
entities:
* omapdss, located in drivers/video/fbdev/omap2/dss/. This is a driver for the
display subsystem IPs used on OMAP (and related) SoCs. It offers only a
kernel internal API, and does not implement anything for fbdev or drm.
* omapdss panels and encoders, located in
drivers/video/fbdev/omap2/displays-new/. These are panel and external encoder
drivers, which use APIs offered by omapdss driver. These also don't implement
anything for fbdev or drm.
* omapdrm, located in drivers/gpu/drm/omapdrm/. This is a drm driver, which
uses omapdss and the panel/encoder drivers to operate the hardware.
* omapfb, located in drivers/video/fbdev/omap2/omapfb/. This is an fbdev
driver, which uses omapdss and the panel/encoder drivers to operate the
hardware.
* omap_vout, located in drivers/media/platform/omap/. This is a v4l2 driver,
which uses omapdss and omapfb to implement a v4l2 API for the video overlays.
So, on the top level, we have either omapdrm, or omapfb+omap_vout. Both of
those use the same low level drivers. Without going to the historical details
why the architecture is like that, I think it's finally time to change that.
The situation with omapfb+omap_vout is that it still works, but no new features
have been added for a long time, and I want to keep it working as it's still
being used. At some point in the future I'd like to remove omapfb and
omap_vout altogether.
Omapdrm, on the other hand, is being actively developed. Sharing the low level
parts with omapfb makes that development more difficult than it should be. It
also "hides" half of the development, as everything happening in the low level
parts resides under fbdev directory, not in the drm directory.
I've been wanting to clean this up for a long time, but I haven't figured out a
very good way to do it. I still haven't, but here's the best way I have come up
with.
This series makes a full copy of the low level parts, omapdss and panel/encoder
drivers. Both omapfb+omap_vout and omapdrm will have their own versions. The
copy omapfb+omap_vout get is a new copy, and the copy that omapdrm gets is just
the current files moved. This way git will associate the omapdrm version with
the old files.
The omapfb+omap_vout versions won't be touched unless there are some big issues
there.
The omapdrm versions can be refactored and cleaned up, as the omapfb support
code is no longer needed. We can perhaps also merge omapdss and omapdrm into
the same kernel module.
This series only does the copy, and the absolutely necessary parts. No further
cleanups are done yet.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
At the moment omapfb and omapdrm can be compiled at the same time, if
both are modules. However, they can't be both loaded, as they use the
same hardware. This has been mostly for compile testing.
To make it clear that omapfb and omapdrm are mutually exclusive drivers,
this patch makes omapfb available only if omapdrm is disabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
gpiod_set_value_cansleep is a noop when the passed descriptor is NULL.
So there is no need to duplicate the check for NULL; just call the
function unconditionally instead.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This makes .disable operate in reverse order compared to .enable.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The WARN() macro has to take a condition. The current code will just
print the stack trace and the function name instead of the intended
warning message.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Device node iterators perform an of_node_put on each iteration, so putting
an of_node_put before a continue results in a double put.
A simplified version of the semantic match that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
iterator i;
@@
i(..., child, ...) {
... when != of_node_get(child)
* of_node_put(child);
...
* continue;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Boolean tests do not need explicit comparison to true or false.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSI_IRQ_SYNC_LOST was ORed twice so we can remove one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
All the output drivers check for 'out' being NULL, but it can never be
NULL. Remove the check.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
A bunch of dispc functions are only used inside dispc, so we can make
them static.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
dss_feat_get_supported_displays() and dss_feat_get_supported_outputs()
are not used outside omapdss, but are exported. We can thus remove the
export and move the declarations to the omapdss internal header.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The functions dispc_ovl_set_fifo_threshold and
dispc_ovl_compute_fifo_thresholds are exported, but not declared in
public headers, and thus are not used outside omapdss. So we can remove
the EXPORT_SYMBOL()s.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
dispc_wb_setup() handles configuration only for mem-to-mem case. This
patch adds the necessary configuration to handle also display capture
mode.
We need to set CAPTUREMODE to 0 (continuous capture), and WBDELAYCOUNT
according to the vertical timings of the display, so that the WB FIFO
has time to flush before the next frame starts.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The color conversion coefficients for RGB to YUV conversion (used with
writeback) don't result in the correct result. This patch sets the
correct coefficients.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When doing mem-to-mem writeback, there's no pixelclock. However, the
code that calculates scaling factors check that there is a pixel clock.
We can just skip the check when doing mem-to-mem writeback.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Mflag thresholds for all pipelines are set in dispc_init_mflag(), but we
are missing that for WB pipeline. Add WB configuration.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fifo thresholds for all pipelines are set in dispc_init_fifos(), but we
are missing it for WB pipeline. Add that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Burst size for all pipelines is set in dispc_configure_burst_sizes(),
but we are missing WB pipe. So add that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add handling of OMAP_DSS_CHANNEL_WB to dispc_ovl_set_channel_out() and
dispc_ovl_get_channel_out().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Refactor dispc_ovl_get_channel_out() to a bit cleaner form, which makes
it easier to add support for writeback in the following patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At the moment we have a function to get the number of writeback
pipelines supported. However, the function is used in a wrong way,
causing a wrong pipeline to get configured when trying to use WB. Also,
we only have a single writeback pipeline on any of the DSS versions.
To fix and simplify this, create a 'has_writeback' flag into the dispc
driver, and after checking the flag, use OMAP_DSS_WB pipeline
explicitly when calling the configuration functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP5+ DSS has a writeback pipeline, but this was not specified in the
features list for OMAP5 DSS.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
By default DISPC asserts hsync and vsync sequentially, i.e. there's
first hsync and that is immediately followed by vsync. This is the only
available behaviour on OMAP2/3, and default behaviour on OMAP4+.
OMAP4+ has ALIGN bit in POL_FREQ register, which makes DISPC assert both
syncs at the same time.
It has been observed that some panels don't like sequential syncs (AM5
EVM's panel). After studying the datasheets for multiple panels and
encoders, and MIPI DPI spec, it looks like there is no standard way to
handle this.
Sometimes the datasheets don't mention the required syncs behaviour at
all, sometimes the datasheets have images that hint towards simultaneous
syncs, and sometimes it is explicitly mentioned that simultaneous syncs
are needed. No panels or encoders requiring sequential sync was found.
It thus seems to be safe to default to simultaneous syncs when the ALIGN
bit is available. This fixed AM5 EVM's panel, and no side effects have
been observed on other panels or encoders.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Update omapdss driver to set the state of the pins to:
- "default on resume
- "sleep" on suspend
By optionally putting the pins into sleep state in the suspend callback
we can accomplish two things.
- minimize current leakage from pins and thus save power,
- prevent the IP from driving pins output in an uncontrolled manner,
which may happen if the power domain drops the domain regulator.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch brings a first support of pxa framebuffer devices to a
devicetree pxa platform, as was before platform data.
There are restrictions with this port, the biggest one being the lack of
support of smart panels. Moreover the conversion doesn't provide a way
to declare multiple framebuffer configurations with different bits per
pixel, only the LCD hardware bus width is used.
The patch was tested on both pxa25x, pxa27x and pxa3xx platform (namely
lubbock, mainstone and zylonite).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to prepare the transition to a mixed platform data and
device-tree initialization, remove all the platform data references all
over the driver.
Copy the platform data into the internal structure of the pxafb, and
only use this afterward.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There's no point in having support for framebuffer notifications
is CONFIG_FB is disabled. This commit adds the necessary stubs
for code to link properly when CONFIG_FB=n and moves fb-notify.o
to be built only when CONFIG_FB=y.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When the usual fbcon legacy options are enabled we have
->register_framebuffer
->fb notifier chain calls into fbcon
->fbcon sets up console on new fbi
->fbi->set_par
->drm_fb_helper_set_par exercises full kms api
And because of locking inversion hilarity all of register_framebuffer
is done with the console lock held. Which means that the first time on
driver load we exercise _all_ the kms code (all probe paths and
modeset paths for everything connected) is under the console lock.
That means if anything goes belly-up in that big pile of code nothing
ever reaches logfiles (and the machine is dead).
Usual tactic to debug that is to temporarily remove those console_lock
calls to be able to capture backtraces. I'm fed up writing this patch
and recompiling kernels. Hence this patch here to add an unsafe,
kernel-taining option to do this at runtime.
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At least NV3 requires for chip to be unlocked before it is possible to
access I2C registers. Without it, it is not possible to read EDID.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The sm712fb framebuffer driver encloses the power-management
functions in #ifdef CONFIG_PM, but the smtcfb_pci_suspend/resume
functions are only really used when CONFIG_PM_SLEEP is also
set, as a frequent gcc warning shows:
fbdev/sm712fb.c:1549:12: warning: 'smtcfb_pci_suspend' defined but not used
fbdev/sm712fb.c:1572:12: warning: 'smtcfb_pci_resume' defined but not used
The driver also avoids using the SIMPLE_DEV_PM_OPS macro when
CONFIG_PM is unset, which is redundant.
This changes the driver to remove the #ifdef and instead mark
the functions as __maybe_unused, which is a nicer anyway, as it
provides build testing for all the code in all configurations
and is harder to get wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The auo_k190x framebuffer driver encloses the power-management
functions in #ifdef CONFIG_PM, but the auok190x_suspend/resume
functions are only really used when CONFIG_PM_SLEEP is also
set, as a frequent gcc warning shows:
drivers/video/fbdev/auo_k190x.c:859:12: warning: 'auok190x_suspend' defined but not used
drivers/video/fbdev/auo_k190x.c:899:12: warning: 'auok190x_resume' defined but not used
This changes the driver to remove the #ifdef and instead mark
the functions as __maybe_unused, which is a nicer anyway, as it
provides build testing for all the code in all configurations
and is harder to get wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The sis framebuffer driver complains with a compile-time warning
if neither the FB_SIS_300 nor FB_SIS_315 symbols are selected:
drivers/video/fbdev/sis/sis_main.c:61:2: warning: #warning Neither CONFIG_FB_SIS_300 nor CONFIG_FB_SIS_315 is se
This is reasonable because it doesn't work in that case, but it's
also annoying for randconfig builds and is one of the most common
warnings I'm seeing on ARM now.
This changes the Kconfig logic to prevent the silly configuration,
by always selecting the FB_SIS_300 variant if the other one is
not set.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As of commit 44d88c754e ("ARM: shmobile: Remove legacy SoC code
for R-Mobile A1"), the SH-Mobile HDMI driver is no longer used.
In theory it could still be used on R-Mobile A1 SoCs, but that requires
adding DT support to the driver, which is not planned.
Remove the driver, it can be resurrected from git history when needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
These geode ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This claims and enables regulators listed in the simple framebuffer dt
node. This is needed so that regulators powering the display pipeline
and external hardware, described in the device node and known by the
kernel code, will remain properly enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The value of d_best is always 0 and never changes.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Otherwise check_timings fails and we get a "has no modes" message
from xrandr.
This fix makes the venc assume PAL and NTSC timings that match the
timings synthetized by copy_timings_drm_to_omap() from omapdrm
mode settings so that check_timings() succeeds.
Tested on: BeagleBoard XM, GTA04 and OpenPandora
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If diu_ops is not implemented on platform, kernel will access a NULL
pointer. We need to check this pointer in DIU initialization.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Acked-by: Timur Tabi <timur@tabi.org>
Cc: stable@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Walleij