Support the composing (at VIDEO_CAPTURE) with the _selection API.
v4l2-compliance successfully run ("test Composing: OK")
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Upon a S_FMT the input/requested frame size and pixel format is
overwritten by the current sub-device settings.
Fix this so application can actually set the frame size and format.
Fixes: 417d2e507e ("[media] media: platform: add VPFE capture driver support for AM437X")
Cc: <stable@vger.kernel.org> # v4.0+
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Dump the VOU registers in log_status.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This converts this driver to videobuf2. As usual it is a big and hard to review
patch, but this is always a big-bang change.
It has been tested with my Renesas board.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The bytesperline values were wrong for planar formats where bytesperline is
the line length for the first plane.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This ensures that both do the same checks, and simplifies s_fmt_vid_out
a bit.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement g/s_selection. The v4l2 core will emulate g/s_crop and
cropcap on top of g/s_selection.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It was set to a format that wasn't supported.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Video output drivers must support these ioctls. Otherwise applications
cannot deduce that these outputs exist and what capabilities they have.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This allows us to drop the use_count and you get free G/S_PRIORITY support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix v4l2-compliance errors due to empty driver and bus_info fields.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Simplify the sh-vou clean up by using devm_* were possible.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make sure that there are valid values in the crop rectangle to ensure
that the color plane doesn't get shifted when cropping.
Since there is no distinction between 12bit and 16bit YUV formats in
at the subdev level, use the more restrictive 12bit limits for all YUV
formats.
Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When stopping the pipeline the driver waits for the pipeline state to be
set to VSP1_PIPELINE_STOPPED but fails to lock the pipe irqlock to read
the state variable protected by the lock. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix Suspend-to-RAM so that VSP1 driver continues to work after resuming.
In detail,
- Fix the judgment of ref count in resuming.
- Add stopping VSP1 during suspend.
[Refactor the suspend and resume code to lower suspend delay]
Signed-off-by: Sei Fumizono <sei.fumizono.jw@hitachi-solutions.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
FXA bit of VI6_DPR_mod_ROUTE register starts from 16bit. But VI6_DPR_ROUTE_FXA_MASK
is set to become start from 8bit. This fixes shift size for VI6_DPR_ROUTE_FXA_MASK.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
FP bit of VI6_DPR_mod_ROUTE register is 6bit. But VI6_DPR_ROUTE_FP_MASK is set
to 0xFF, this will mask until the reserve bit.
This fixes size for VI6_DPR_ROUTE_FP_MASK.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Clipping size bit of VI6_WPFn _HSZCLIP and VI6_WPFn _VSZCLIP register are from
0 bit to 11 bit. But VI6_WPF_SZCLIP_SIZE_MASK is set to 0x1FFF, this will mask
until the reserve bits. This fixes size for VI6_WPF_SZCLIP_SIZE_MASK.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The runtime pm resume/suspend will enable/disable pclk (ISI peripheral
clock).
We have to call runtime_pm_get_sync()/runtime_pm_put() when we need to
access ISI registers. In atmel_isi_probe(), remove the isi disable code
as at that moment ISI peripheral clock is not enable yet.
Besides, clock_start()/clock_stop() is used to control the mclk, not
the ISI peripheral clock. So move this to start[stop]_streaming()
function.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In current code, stop_streaming() will just return if ISI is still
working in the codec. But this is incorrect, we need to disable ISI even
it is working on the codec, otherwise stop_streaming() will not work as
we expected.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 813f5c0ac5 ("media: Change media device link_notify behaviour")
modified the media controller link setup notification API and updated the
OMAP3 ISP driver accordingly. As a side effect it introduced a bug by
turning power on after setting the link instead of before. This results in
sub-devices not being powered down in some cases when they should be. Fix
it.
Fixes: 813f5c0ac5 [media] media: Change media device link_notify behaviour
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Cc: stable@vger.kernel.org # since v3.10
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The async notifier was registered before the v4l2_device was registered and
before the notifier callbacks were set. This could lead to missing the
bound() and complete() callbacks and to attempting to spin_lock() and
uninitialised spin lock.
Also fix unregistering the async notifier in the case of an error --- the
function may not fail anymore after the notifier is registered.
Fixes: da7f3843d2 ("[media] omap3isp: Add support for the Device Tree")
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Added support for reduced blanking version 2 (RB v2) in cvt timings.
Standard specifies a fixed vsync pulse of 8 lines to indicate RB v2
timings. Vertical back porch is fixed at 6 lines and vertical front
porch is remainder of vertical blanking time.
For RB v2, horizontal blanking is fixed at 80 pixels. Horizontal sync
is fixed at 32. All horizontal timing counts (active pixels, front,
back porches) can be specified upto a precision of 1.
RB v2 allows for non standard aspect ratios. In RB v2 vsync does not
indicate aspect ratio. In absence of aspect ratio v4l2_detect_cvt()
cannot calculate image width from image height. Hence extending the
v4l2_detect_cvt() to pass image width in case of RB v2.
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
To be consistent with other kernel interface namings, rename
of_get_named_gen_pool() to of_gen_pool_get(). In the original function
name "_named" suffix references to a device tree property, which contains
a phandle to a device and the corresponding device driver is assumed to
register a gen_pool object.
Due to a weak relation and to avoid any confusion (e.g. in future
possible scenario if gen_pool objects are named) the suffix is removed.
[sfr@canb.auug.org.au: crypto/marvell/cesa - fix up for of_get_named_gen_pool() rename]
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To be consistent with other genalloc interface namings, rename
dev_get_gen_pool() to gen_pool_get(). The original omitted "dev_" prefix
is removed, since it points to argument type of the function, and so it
does not bring any useful information.
[akpm@linux-foundation.org: update arch/arm/mach-socfpga/pm.c]
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Mark Brown <broonie@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Alan Tull <atull@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.2.
I've one other new driver from freescale on my radar, it's been posted
and reviewed, I'd just like to get someone to give it a last look, so
maybe I'll send it or maybe I'll leave it.
There is no major nouveau changes in here, Ben was working on
something big, and we agreed it was a bit late, there wasn't anything
else he considered urgent to merge.
There might be another msm pull for some bits that are waiting on
arm-soc, I'll see how we time it.
This touches some "of" stuff, acks are in place except for the fixes
to the build in various configs,t hat I just applied.
Summary:
New drivers:
- virtio-gpu:
KMS only pieces of driver for virtio-gpu in qemu.
This is just the first part of this driver, enough to run
unaccelerated userspace on. As qemu merges more we'll start
adding the 3D features for the virgl 3d work.
- amdgpu:
a new driver from AMD to driver their newer GPUs. (VI+)
It contains a new cleaner userspace API, and is a clean
break from radeon moving forward, that AMD are going to
concentrate on. It also contains a set of register headers
auto generated from AMD internal database.
core:
- atomic modesetting API completed, enabled by default now.
- Add support for mode_id blob to atomic ioctl to complete interface.
- bunch of Displayport MST fixes
- lots of misc fixes.
panel:
- new simple panels
- fix some long-standing build issues with bridge drivers
radeon:
- VCE1 support
- add a GPU reset counter for userspace
- lots of fixes.
amdkfd:
- H/W debugger support module
- static user-mode queues
- support killing all the waves when a process terminates
- use standard DECLARE_BITMAP
i915:
- Add Broxton support
- S3, rotation support for Skylake
- RPS booting tuning
- CPT modeset sequence fixes
- ns2501 dither support
- enable cmd parser on haswell
- cdclk handling fixes
- gen8 dynamic pte allocation
- lots of atomic conversion work
exynos:
- Add atomic modesetting support
- Add iommu support
- Consolidate drm driver initialization
- and MIC, DECON and MIPI-DSI support for exynos5433
omapdrm:
- atomic modesetting support (fixes lots of things in rewrite)
tegra:
- DP aux transaction fixes
- iommu support fix
msm:
- adreno a306 support
- various dsi bits
- various 64-bit fixes
- NV12MT support
rcar-du:
- atomic and misc fixes
sti:
- fix HDMI timing complaince
tilcdc:
- use drm component API to access tda998x driver
- fix module unloading
qxl:
- stability fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (872 commits)
drm/nouveau: Pause between setting gpu to D3hot and cutting the power
drm/dp/mst: close deadlock in connector destruction.
drm: Always enable atomic API
drm/vgem: Set unique to "vgem"
of: fix a build error to of_graph_get_endpoint_by_regs function
drm/dp/mst: take lock around looking up the branch device on hpd irq
drm/dp/mst: make sure mst_primary mstb is valid in work function
of: add EXPORT_SYMBOL for of_graph_get_endpoint_by_regs
ARM: dts: rename the clock of MIPI DSI 'pll_clk' to 'sclk_mipi'
drm/atomic: Don't set crtc_state->enable manually
drm/exynos: dsi: do not set TE GPIO direction by input
drm/exynos: dsi: add support for MIC driver as a bridge
drm/exynos: dsi: add support for Exynos5433
drm/exynos: dsi: make use of array for clock access
drm/exynos: dsi: make use of driver data for static values
drm/exynos: dsi: add macros for register access
drm/exynos: dsi: rename pll_clk to sclk_clk
drm/exynos: mic: add MIC driver
of: add helper for getting endpoint node of specific identifiers
drm/exynos: add Exynos5433 decon driver
...
drivers/media/platform/omap3isp/isppreview.c:932:6: warning: variable ‘features’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver requires support for DMA attrs function, and not
just DMA. Change the options accordingly to remove those errors:
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c: In function ‘bdisp_hw_free_nodes’:
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c:132:3: error: implicit declaration of function ‘dma_free_attrs’ [-Werror=implicit-function-declaration]
dma_free_attrs(ctx->bdisp_dev->dev,
^
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c: In function ‘bdisp_hw_alloc_nodes’:
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c:157:9: error: implicit declaration of function ‘dma_alloc_attrs’ [-Werror=implicit-function-declaration]
base = dma_alloc_attrs(dev, node_size * MAX_NB_NODE, &paddr,
^
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c:157:7: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
base = dma_alloc_attrs(dev, node_size * MAX_NB_NODE, &paddr,
^
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c: In function ‘bdisp_hw_alloc_filters’:
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c:219:7: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
base = dma_alloc_attrs(dev, size, &paddr, GFP_KERNEL | GFP_DMA, &attrs);
Also, get rid of bogus, unused and duplicated symbol declaration
for the config option done at bdisp/Kconfig.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are several warnings there, on some architectures, related
to dividing a s32 by a s64 value:
drivers/media/platform/sti/bdisp/bdisp-debug.c:594: warning: comparison of distinct pointer types lacks a cast
drivers/media/platform/sti/bdisp/bdisp-debug.c:594: warning: right shift count >= width of type
drivers/media/platform/sti/bdisp/bdisp-debug.c:594: warning: passing argument 1 of '__div64_32' from incompatible pointer type
drivers/media/platform/sti/bdisp/bdisp-debug.c:595: warning: comparison of distinct pointer types lacks a cast
drivers/media/platform/sti/bdisp/bdisp-debug.c:595: warning: right shift count >= width of type
drivers/media/platform/sti/bdisp/bdisp-debug.c:595: warning: passing argument 1 of '__div64_32' from incompatible pointer type CC [M] drivers/media/tuners/mt2060.o
drivers/media/platform/sti/bdisp/bdisp-debug.c:596: warning: comparison of distinct pointer types lacks a cast
drivers/media/platform/sti/bdisp/bdisp-debug.c:596: warning: right shift count >= width of type
drivers/media/platform/sti/bdisp/bdisp-debug.c:596: warning: passing argument 1 of '__div64_32' from incompatible pointer type
drivers/media/platform/sti/bdisp/bdisp-debug.c:597: warning: comparison of distinct pointer types lacks a cast
drivers/media/platform/sti/bdisp/bdisp-debug.c:597: warning: right shift count >= width of type
drivers/media/platform/sti/bdisp/bdisp-debug.c:597: warning: passing argument 1 of '__div64_32' from incompatible pointer type
That doesn't make much sense. What the driver is actually trying
to do is to divide one second by a value. So, check the range
before dividing. That warrants the right result and will remove
the warnings on non-64 bits archs.
Also fixes this warning:
drivers/media/platform/sti/bdisp/bdisp-debug.c:588: warning: comparison of distinct pointer types lacks a cast
by using div64_s64() instead of calling do_div() directly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix the following warning:
drivers/media/platform/sti/bdisp/bdisp-v4l2.c: In function 'bdisp_register_device':
drivers/media/platform/sti/bdisp/bdisp-v4l2.c:1024:26: warning: variable 'pdev' set but not used [-Wunused-but-set-variable]
struct platform_device *pdev;
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/platform/sti/bdisp/bdisp-v4l2.c:947 bdisp_s_selection() warn: unsigned 'out.width' is never less than zero.
drivers/media/platform/sti/bdisp/bdisp-v4l2.c:947 bdisp_s_selection() warn: unsigned 'out.height' is never less than zero.
Indeed, width and height are unsigned.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The coda tracing code causes lots of warnings like
In file included from /git/arm-soc/include/trace/define_trace.h:90:0,
from /git/arm-soc/drivers/media/platform/coda/trace.h:203,
from /git/arm-soc/drivers/media/platform/coda/coda-bit.c:34:
/git/arm-soc/include/trace/ftrace.h:28:0: warning: "TRACE_SYSTEM_STRING" redefined
#define TRACE_SYSTEM_STRING __app(TRACE_SYSTEM_VAR,__trace_system_name)
^
In file included from /git/arm-soc/include/trace/define_trace.h:83:0,
from /git/arm-soc/drivers/media/platform/coda/trace.h:203,
from /git/arm-soc/drivers/media/platform/coda/coda-bit.c:34:
/git/arm-soc/drivers/media/platform/coda/./trace.h:12:0: note: this is the location of the previous definition
#define TRACE_SYSTEM_STRING __stringify(TRACE_SYSTEM)
>From what I can tell, this is just the result of a bogus TRACE_SYSTEM_STRING
definition, and removing that one makes the warnings go away.
Fixes: 9a1a8f9953 ("[media] coda: Add tracing support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Creates 5 debugfs entries to dump the last HW request, the last HW node
(=command), the HW registers and the recent HW performance (time & fps)
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This v4l2 mem2mem driver is a 2D blitter for STMicroelectronics SoC.
It uses the v4l2 mem2mem framework.
The following features are supported and tested:
- Color format conversion (RGB32, RGB24, RGB16, NV12, YUV420P)
- Copy
- Scale
- Flip
- Deinterlace
- Wide (4K) picture support
- Crop
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: added missing slab.h include to bdisp-v4l2.c]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Extend detect_cvt/gtf API to indicate the format type (interlaced
or progressive). In case of interlaced, the vertical front and back
porch and vsync values for both (odd,even) fields are considered to
derive image height. Populated vsync, vertical front, back porch
values in bt timing structure for even and odd fields and updated
the flags appropriately.
Also modified the functions calling the detect_cvt/gtf(). As of now
these functions are calling detect_cvt/gtf() with interlaced flag
set to false.
Cc: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the missing VIDIOC_CREATE_BUFS and VIDIOC_PREPARE_BUF
ioctls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently the colors for the Y16 and Y16_BE pixelformats are in the range
0x0000-0xff00. So pure white (0xffff) is never created.
Improve this by making white really white. For other colors the lsb remains 0
so vivid can be used to detect endian problems.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Ricardo Ribalda <ricardo.ribalda@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This has been on my TODO list for some time now: the control that enables the video
loopback was part of the controls of the video output device instead of the video
capture device. In practice this was quite annoying since you expect it at the capture
side since that's where you want to make the decision whether to use the TPG or looped
video.
This patch moves the control from the output to the capture side.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 84cb7be43c broke vivid-tpg
(uninitialized variable p).
This patch takes a different approach: four different functions are
created, one for each PRINTSTR version.
In order to avoid the 'the frame size of 1308 bytes is larger than 1024
bytes' warning I had to mark those functions with 'noinline'. For
whatever reason gcc seems to inline this aggressively and it is doing
weird things with the stack.
I tried to read the assembly code, but I couldn't see what exactly it
was doing on the stack.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Precalculate all the colorspace/transfer function combinations in order
to easily generate the correct colors.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the transfer function: create a new control for it,
and support it for both capture and output sides.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make this part of the format check.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Smatch reports two issues:
drivers/media/platform/sh_vou.c:670 vou_adjust_output() error: buffer overflow 'vou_scale_v_num' 3 <= 4
drivers/media/platform/sh_vou.c:670 vou_adjust_output() error: buffer overflow 'vou_scale_v_den' 3 <= 4
It seems that there's actually a bug here: the same var (idx) is used
as an index for vertical and horizontal scaling arrays. However,
there are 4 elements on the h arrays, and only 3 at the v ones.
On the first loop, it may select index 4 for the horizontal array.
In this case, if the second loop fails to select an index, the
code would keep using 4 for the vertical array, with is past of
the array sizes.
The intent here seems to use index 0, if the scale is not found.
So, use a separate var for the vertical index.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove the following compilation warnings:
drivers/media/platform/vivid/vivid-tpg.c: In function 'tpg_gen_text':
drivers/media/platform/vivid/vivid-tpg.c:1562:1: warning: the frame size of 1308 bytes is larger than 1024 bytes [-Wframe-larger-than=]
}
^
This seems to be due to some bad optimization done by gcc.
Moving the for() loop to happen inside the macro solves the
issue.
While here, fix CodingStyle at the switch().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Commits a0f10c131c and
6c9fe76536 ("media: s5p-mfc: fix broken
pointer cast on 64bit arch") fixed issue with lossy cast on 64-bit
architectures. However it also removed __iomem attribute from that cast.
This leads to sparse warnings. This patch fixes those warnings by adding
__iomem cast in case of v6+ code version and replacing readl/writel by
simple u32 load/store operations in case of v5 code (which is called on
system memory allocated by dma_alloc_coherent() instead of io registers).
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch makes use of helper function v4l2_get_timestamp()
to set the timestamp of vb2 buffer.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
After adding virtio-gpu I get this funky kconfig dependency loop.
scripts/kconfig/conf --oldconfig Kconfig
drivers/video/fbdev/Kconfig:5:error: recursive dependency detected!
drivers/video/fbdev/Kconfig:5: symbol FB is selected by DRM_KMS_FB_HELPER
drivers/gpu/drm/Kconfig:34: symbol DRM_KMS_FB_HELPER is selected by DRM_VIRTIO_GPU
drivers/gpu/drm/virtio/Kconfig:1: symbol DRM_VIRTIO_GPU depends on VIRTIO
drivers/virtio/Kconfig:1: symbol VIRTIO is selected by REMOTEPROC
drivers/remoteproc/Kconfig:4: symbol REMOTEPROC is selected by OMAP_REMOTEPROC
drivers/remoteproc/Kconfig:12: symbol OMAP_REMOTEPROC depends on OMAP_IOMMU
drivers/iommu/Kconfig:141: symbol OMAP_IOMMU is selected by VIDEO_OMAP3
drivers/media/platform/Kconfig:96: symbol VIDEO_OMAP3 depends on VIDEO_V4L2
drivers/media/v4l2-core/Kconfig:6: symbol VIDEO_V4L2 depends on I2C
drivers/i2c/Kconfig:7: symbol I2C is selected by FB_DDC
drivers/video/fbdev/Kconfig:59: symbol FB_DDC is selected by FB_CYBER2000_DDC
drivers/video/fbdev/Kconfig:374: symbol FB_CYBER2000_DDC depends on FB_CYBER2000
drivers/video/fbdev/Kconfig:362: symbol FB_CYBER2000 depends on FB
Making VIDEO_OMAP3 depend on OMAP_IOMMU instead of selecting it breaks the
loop, which looks like the best way to handle it to me. Updated OMAP_IOMMU
help text accordingly.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use these defines instead of hardcoding this in any driver that needs it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support for V4L2_PIX_FMT_Y16_BE, a 16 bit big endian greyscale format.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Even though the rcar-vin driver tells userspace that it will give a monotonic
timestamp, it is actually using gettimeofday. Replace this with a proper
monotonic timestamp.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove code duplication by merging two cases in a switch.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support for V4L2_PIX_FMT_Y16, a 16 bit greyscale format.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
My static checker warns that the name of the port can be 15 characters
when you consider the NUL terminator and that's one more than the 14
characters in name[]. Maybe it's an off-by-one?
It's unlikely that we hit the limit and even if we do the overflow will
only affect one of the two bytes of padding so it's harmless. Still
let's fix it and also change the sprintf() to snprintf().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Without i2c, we can get a build error:
drivers/media/platform/exynos4-is/fimc-is-i2c.c: In function 'fimc_is_i2c_probe':
drivers/media/platform/exynos4-is/fimc-is-i2c.c:58:8: error: implicit declaration of function 'i2c_add_adapter' [-Werror=implicit-function-declaration]
The dependency already exists for exynos-fimc-lite and s5p-fimc,
but is missing for exynos4-fimc.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The RGB444 format swapped the red and blue components, fix this.
Rather than making a new BGR444 format (as I proposed initially), Jon prefers
to just fix this and return the colors in the right order. I think that makes
sense in this case.
Since the RGB444 pixel format is deprecated due to the ambiguous specification
of the alpha component we use the XRGB444 pixel format instead (specified as having
no alpha channel).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
[mchehab@osg.samsung.com: fix a merge conflict at adv7604.c]
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Setting the last buffer flag causes the videobuf2 core to return -EPIPE from
DQBUF calls on the capture queue after the last buffer is dequeued.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Setting the last buffer flag causes the videobuf2 core to return -EPIPE from
DQBUF calls on the capture queue after the last buffer is dequeued.
This patch also fixes the EOS event to conform to the specification. It now is
sent right after the last buffer has been decoded instead of when the last
buffer is dequeued.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
[k.debski@samsung.com: Fix misspelling in title (s/sp5/s5p/)]
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVT9fTAAoJEHm+PkMAQRiGrbYH/276n6aKSORO0B6DrEnebu8Y
oxfJeacg90/N5aLx/B5GEplO24uTENaAfB342WkexziXdY+7P02J0Y36eSh5WiL2
qcL+gkiZVaApZIjVeO/y2ByL7nLprPeIsxl5gGLhI+qYYMaQ8gtzxC7sDLnNqjPS
w8WYQB7LdWeGFqcuvySEX2C6Q62aHpZWoSsV3LYdrfoDJz2lv1DJrOpRhqXPagl7
oX1c1CWQ4yWdFf9xm8vaiZw7EskxEnObQm7n7vWlZ0xAhXZ/3a7bPdc+fj2V+nve
xjZV/EhEL0u3ME86bVtcqbO3lgMjivyWHjQglCwG6keS+iIHkL0xMlQabkrFJhw=
=LGDf
-----END PGP SIGNATURE-----
Merge tag 'v4.1-rc3' into patchwork
Linux 4.1-rc3
* tag 'v4.1-rc3': (381 commits)
Linux 4.1-rc3
drm: Zero out invalid vblank timestamp in drm_update_vblank_count.
m32r: make flush_cpumask non-volatile.
mnt: Fix fs_fully_visible to verify the root directory is visible
path_openat(): fix double fput()
namei: d_is_negative() should be checked before ->d_seq validation
ARM: dts: Add keep-power-in-suspend to WiFi SDIO node for exynos5250-snow
ARM: dts: Fix typo in trip point temperature for exynos5420/5440
ARM: dts: add 'rtc_src' clock to rtc node for exynos4412-odroid boards
ARM: dts: Make DP a consumer of DISP1 power domain on Exynos5420
MAINTAINERS: add Conexant Digicolor machines entry
MAINTAINERS: socfpga: update the git repo for SoCFPGA
drm/tegra: Don't use vblank_disable_immediate on incapable driver.
mmc: dw_mmc: dw_mci_get_cd check MMC_CAP_NONREMOVABLE
mmc: dw_mmc: init desc in dw_mci_idmac_init
ARM: multi_v7_defconfig: Select more FSL SoCs
MAINTAINERS: replace an AT91 maintainer
drivers: CCI: fix used_mask init in validate_group()
drm/radeon: stop trying to suspend UVD sessions
drm/radeon: more strictly validate the UVD codec
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gmuD
-----END PGP SIGNATURE-----
Merge tag 'media/v4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Three driver fixes:
- fix for omap4, fixing a regression due to a subsystem API that got
removed for 4.1 (commit efde234674);
- fix for one of the formats supported by Marvel ccic driver;
- fix rcar_vin driver that, when stopping abnormally, the driver
can't return from wait_for_completion"
* tag 'media/v4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] v4l: omap4iss: Replace outdated OMAP4 control pad API with syscon
[media] media: soc_camera: rcar_vin: Fix wait_for_completion
[media] marvell-ccic: fix Y'CbCr ordering
Replace all calls to s_mbus_fmt in bridge drivers by calls to the
set_fmt pad op.
Remove the old try/s_mbus_fmt video ops since they are now no longer used.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace all calls to try_mbus_fmt in bridge drivers by calls to the
set_fmt pad op.
[mchehab@osg.samsung.com: fix a merge conflict at mcam-core.c]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The try_mbus_fmt video op is a duplicate of the pad op. Replace all uses
in sub-devices by the set_fmt() pad op.
Since try_mbus_fmt and s_mbus_fmt both map to the set_fmt pad op (but
with a different 'which' argument), this patch will replace both
try_mbus_fmt and s_mbus_fmt by set_fmt.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The g_mbus_fmt video op is a duplicate of the pad op. Replace all uses
by the get_fmt pad op and remove the video op.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace all calls to the enum_mbus_fmt video op by the pad
enum_mbus_code op and remove the duplicate video op.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kamil Debski <k.debski@samsung.com>
Acked-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If i2c_add_adapter() fails, adap is not deallocated.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The REG_CTRL0 register was never written if this format was selected,
instead an error was logged and whatever was last set in that register
was used.
Surprisingly, that seems to work if YUYV was selected, but we should
program this register explicitly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I cannot get this format to work, the colors keep coming out wrong.
Since this has never worked I just drop support for this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These were calculated incorrectly for the planar formats.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver appeared to support the JPEG format when in reality
that was just dead code. Remove it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The dma-vmalloc implementation didn't support planar formats, but with
a little bit of refactoring that is easy to fix.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If start_streaming fails or stop_streaming is called, then all queued
buffers need to be given back to vb2.
This prevents vb2 from calling WARN_ON when it detects that this is not
done correctly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
- fill in timestamp
- fill in field
- start the sequence counter at 0, not 1
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add VB2_DMABUF and VIDIOC_EXPBUF support. Also add VB2_USERPTR support
for the vmalloc DMA mode which was missing for no good reason.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This fixes the final v4l2-compliance warning.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the V4L2 core locking system instead of rolling your own. Switch to
the vb2 fop and ioctl helpers to get rid of a lot of code. This also made
it easy to add VB2_READ to the DMA modes, since you get read() for free
with vb2 and these helpers.
Finally remove the users field: this information is also available from
the core framework, no need to keep track of it in the driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that this driver uses v4l2_fh, it is trivial to add support for
control events. Again, this fixes a v4l2-compliance failure.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use struct v4l2_fh to represent a filehandle. This fixes the missing
g/s_priority handling of this driver that v4l2-compliance complained
about.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
No controls were reported, even though the ov7670 does have controls.
Two reasons for this: the v4l2_ctrl_handler_init() call must come
before the ov7670 is loaded (otherwise the ov7670 won't know that
its controls should be added to the bridge driver), and the
v4l2_ctrl_handler_free() call at the end should only be called if
the ret value is non-zero (otherwise you would just free all the
controls that were just added).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The colorspace field wasn't filled in properly. This fixes a v4l2-compliance
failure.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
TV standards make no sense for webcam drivers, so drop these dummy
functions. This stops v4l2-compliance from complaining about this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The bus_info field of struct v4l2_querycap wasn't filled in and
v4l2-compliance complained about that. Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We must set timestamp_flags in vb2_queue otherwise vb2 will complain
loudly about it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If NO_DMA=y:
warning: (VIDEO_XILINX && VIDEO_DM365_VPFE && VIDEO_DT3155 && VIDEO_OMAP4) selects VIDEOBUF2_DMA_CONTIG which has unmet direct dependencies (MEDIA_SUPPORT && HAS_DMA)
media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’:
media/v4l2-core/videobuf2-dma-contig.c:207: error: implicit declaration of function ‘dma_mmap_coherent’
media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’:
media/v4l2-core/videobuf2-dma-contig.c:390: error: implicit declaration of function ‘dma_get_sgtable’
VIDEO_XILINX selects VIDEOBUF2_DMA_CONTIG, which bypasses its dependency
on HAS_DMA. Make VIDEO_XILINX depend on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The format description is now filled in by the core, so we can
drop this in this virtual driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The format description is now filled in by the core, so we can
drop this in this virtual m2m driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/platform/m2m-deinterlace.c:1063 deinterlace_probe() info: ignoring unreachable code.
There's no need to call v4l2_m2m_release() here, as the last possible
failure in this code is to allocate the m2m struct.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/platform/s5p-mfc/s5p_mfc.c:1340 s5p_mfc_runtime_resume() warn: this array is probably non-NULL. 'm_dev->alloc_ctx'
alloc_ctx can never be NULL, as it is embeeded inside the struct
s5p_mfc_dev.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/platform/am437x/am437x-vpfe.c: In function 'vpfe_ccdc_update_raw_params':
drivers/media/platform/am437x/am437x-vpfe.c:430:38: warning: variable 'config_params' set but not used [-Wunused-but-set-variable]
struct vpfe_ccdc_config_params_raw *config_params =
^
vpfe_ccdc_update_raw_params() is supposed to update the raw
params at ccdc. However, it is just creating a local var and changing
it.
Compile-tested only.
Cc: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix these compiler warnings that appeared after switching to gcc-5.1.0:
drivers/media/platform/s3c-camif/camif-capture.c: In function 'sensor_set_power':
drivers/media/platform/s3c-camif/camif-capture.c:118:10: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
if (!on == camif->sensor.power_count)
^
drivers/media/platform/s3c-camif/camif-capture.c: In function 'sensor_set_streaming':
drivers/media/platform/s3c-camif/camif-capture.c:134:10: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
if (!on == camif->sensor.stream_count)
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For these encodings the quantization range should be ignored, since
there is only one possible Y'CbCr encoding.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to be consistent with the other Y'CbCr encodings add
support for full range V4L2_YCBCR_ENC_BT2020_CONST_LUM.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to be consistent with the other Y'CbCr encodings add
support for full range V4L2_YCBCR_ENC_BT2020.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to be consistent with the other Y'CbCr encodings add
support for full range V4L2_YCBCR_ENC_SMPTE240M.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a log_status function to the test pattern generator and use that
in vivid. This simplifies debugging complex colorspace problems.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the VIVID_WEBCAM_SIZES constant where appropriate and add a
1920x1080 pixel frame size setting with frame rates of 2 fps and
5 fps.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When stopping abnormally, a driver can't return from wait_for_completion.
This patch resolved this problem by changing wait_for_completion_timeout
from wait_for_completion.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Various formats had their byte ordering implemented incorrectly, and
the V4L2_PIX_FMT_UYVY is actually impossible to create, instead you
get V4L2_PIX_FMT_YVYU.
This was working before commit ad6ac45222
("add new formats support for marvell-ccic driver"). That commit broke
the original format support and the OLPC XO-1 laptop showed wrong
colors ever since (if you are crazy enough to attempt to run the latest
kernel on it, like I did).
The email addresses of the authors of that patch are no longer valid,
so without a way to reach them and ask them about their test setup
I am going with what I can test on the OLPC laptop.
If this breaks something for someone on their non-OLPC setup, then
contact the linux-media mailinglist. My suspicion however is that
that commit went in untested.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: <stable@vger.kernel.org> # for v3.19 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* 'drm-next-merged' of git://people.freedesktop.org/~airlied/linux: (9717 commits)
media-bus: Fixup RGB444_1X12, RGB565_1X16, and YUV8_1X24 media bus format
hexdump: avoid warning in test function
fs: take i_mutex during prepare_binprm for set[ug]id executables
smp: Fix error case handling in smp_call_function_*()
iommu-common: Fix PARISC compile-time warnings
sparc: Make LDC use common iommu poll management functions
sparc: Make sparc64 use scalable lib/iommu-common.c functions
Break up monolithic iommu table/lock into finer graularity pools and lock
sparc: Revert generic IOMMU allocator.
tools/power turbostat: correct dumped pkg-cstate-limit value
tools/power turbostat: calculate TSC frequency from CPUID(0x15) on SKL
tools/power turbostat: correct DRAM RAPL units on recent Xeon processors
tools/power turbostat: Initial Skylake support
tools/power turbostat: Use $(CURDIR) instead of $(PWD) and add support for O= option in Makefile
tools/power turbostat: modprobe msr, if needed
tools/power turbostat: dump MSR_TURBO_RATIO_LIMIT2
tools/power turbostat: use new MSR_TURBO_RATIO_LIMIT names
Bluetooth: hidp: Fix regression with older userspace and flags validation
config: Enable NEED_DMA_MAP_STATE by default when SWIOTLB is selected
perf/x86/intel/pt: Fix and clean up error handling in pt_event_add()
...
That solves several merge conflicts:
Documentation/DocBook/media/v4l/subdev-formats.xml
Documentation/devicetree/bindings/vendor-prefixes.txt
drivers/staging/media/mn88473/mn88473.c
include/linux/kconfig.h
include/uapi/linux/media-bus-format.h
The ones at subdev-formats.xml and media-bus-format.h are not trivial.
That's why we opted to merge from DRM.
* patchwork: (404 commits)
[media] uvcvideo: add support for VIDIOC_QUERY_EXT_CTRL
[media] uvcvideo: fix cropcap v4l2-compliance failure
[media] media: omap3isp: remove unused clkdev
[media] coda: Add tracing support
[media] coda: drop dma_sync_single_for_device in coda_bitstream_queue
[media] coda: fix fill bitstream errors in nonstreaming case
[media] coda: call SEQ_END when the first queue is stopped
[media] coda: fail to start streaming if userspace set invalid formats
[media] coda: remove duplicate error messages for buffer allocations
[media] coda: move parameter buffer in together with context buffer allocation
[media] coda: allocate bitstream buffer from REQBUFS, size depends on the format
[media] coda: allocate per-context buffers from REQBUFS
[media] coda: use strlcpy instead of snprintf
[media] coda: bitstream payload is unsigned
[media] coda: fix double call to debugfs_remove
[media] coda: check kasprintf return value in coda_open
[media] coda: bitrate can only be set in kbps steps
[media] v4l2-mem2mem: no need to initialize b in v4l2_m2m_next_buf and v4l2_m2m_buf_remove
[media] s5p-mfc: set allow_zero_bytesused flag for vb2_queue_init
[media] coda: set allow_zero_bytesused flag for vb2_queue_init
...
devicetree changes queued up for v4.1. Here are the highlights:
- Lots of unittest cleanup from Frank Rowand
- Bugfixes and updates to the of_graph code
- Tighten up of_get_mac_address() code
- Documentation updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVMYiQAAoJEMWQL496c2LNyrcP/2acOKeyHk7zBVWxaYe6nO52
iwpDb+UDEdW+1Cx5e+OpF1gqoY7lJ2Q+Uvm65+z00a46Fnl0cWuSYFIV7e0wjE5/
3EAB4cQgiCzToDnbtCu4U6XlpNlQz/q85tV9X/EpYApHNb+BKN6RMzyIDm48lzJY
L6SG4fxFJVpeDxweZFGaWE9/Ildr4vOS+4GZpE0Az3iX2WDrQPioKjuOw8TeUHRO
xwvfv1TpyQFa2qHZLI4AmZSN8VJBw82OuAyZHAGsE4bekfafeqVFt0ZtYYoiAbIM
rw+dUCnWARc7gm8z2PaYnZGs8O++Flb03clDeFrdrvfZIewXWEkZ1TxrKIb9bLyP
A8tlSnbnCdXYSzyaFYH2TgUtc7gQosssfImuJjUq1qQkeEitLP6VzEsekN1h6sx7
axFiBdiCXPvn8ti+AlK9tYfSM0ZhAzvfpuLM0hpTAk3De3NfbJQiyp6eyXAInLne
cs9RGPXNPuKX0tISZ29vA8tmOSrDInfeEEW/Lqu4l+HedcLssWjReY0xVsZS3pbi
xGiD5/Ztdha9keTIQdW+7R0SE1YsZTpwZbQt0HeHcE+pzFPF/3TLIIIYhYRVSPsm
D+g5W+bVxht8NC380UEC8vpAyP1CYSnq/aVrDfJiXZVOS7b/dyZDk6Y6LSBOm9Em
9qLaPASncxVinaNcGlyj
=u6Zy
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree changes from Grant Likely:
"Here are the devicetree changes queued up for v4.1. Nothing really
exciting here. Rob has another few commits for big-endian attached
UARTs, but those will be sent in a separate merge request since they
haven't been as thoroughly tested as this batch.
Here are the highlights:
- lots of unittest cleanup from Frank Rowand
- bugfixes and updates to the of_graph code
- tighten up of_get_mac_address() code
- documentation updates"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of/unittest: Fix of_platform_depopulate test case
of/unittest: early return from test skips tests
of/unittest: breadcrumbs to reduce pain of future maintainers
of/unittest: reduce checkpatch noise - line after declarations
of/unittest: typo in error string
of/unittest: add const where needed
of_net: factor out repetitive code from of_get_mac_address()
drivers/of: Add empty ranges quirk for PA-Semi
of: Allow selection of OF_DYNAMIC and OF_OVERLAY if OF_UNITTEST
of: Empty node & property flag accessors when !OF
of: Explicitly include linux/types.h in of_graph.h
dt-bindings: brcm: rationalize Broadcom documentation naming
of/unittest: replace 'selftest' with 'unittest'
Documentation: rename of_selftest.txt to of_unittest.txt
Documentation: update the of_selftest.txt
dt: OF_UNITTEST make dependency broken
MAINTAINERS: Pantelis Antoniou device tree overlay maintainer
of: Add of_graph_get_port_by_id function
of: Add for_each_endpoint_of_node helper macro
of: Decrement refcount of previous endpoint in of_graph_get_next_endpoint
No merged platform supplies xclks via platform data. As we want to
slightly change the clkdev interface, rather than fixing this unused
code, remove it instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds tracepoints to the coda driver that can be used together
with the v4l2:v4l2_qbuf and v4l2:v4l2_dqbuf tracepoints to to follow video
frames through the mem2mem device.
For encoding with the BIT processor:
coda:coda_enc_pic_run
coda:coda_enc_pic_done
For decoding with the BIT processor:
coda:coda_bit_queue
coda:coda_dec_pic_run
coda:coda_dec_pic_done
coda:coda_dec_rot_done
Additionally, two low level tracepoints register whenever the BIT processor
is started and returns:
coda:coda_bit_run
coda:coda_bit_done
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Issuing a cache flush for the whole bitstream buffer is not optimal in the first
place when only a part of it was written. But given that the buffer is mapped in
writecombine mode, it is not needed at all.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Ian Molton <imolton@ad-holdings.co.uk>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When queueing a buffer into the bitstream fails, it has to be requeued
in the videobuf2 queue before streaming starts, but while streaming it
should be returned to userspace with an error.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This allows to stop and restart the output queue to start a new sequence
while keeping the capture queue running. Before, sequence end would only
be issued if both output and capture queue were stopped and the sequence
start issued when reenabling the output queue would fail.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
coda_alloc_aux_buf already prints an error, no need to print duplicate
error messages all over the place.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The parameter buffer is a per-context buffer, so we can allocate and free it
together with the other context buffers during REQBUFS.
Since this was the last context buffer allocated in coda-common.c, we can now
move coda_alloc_context_buf into coda-bit.c.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Allocating the bitstream buffer only when the format is set allows to guarantee
that at least two frames fit into the bitstream buffer. For small frame sizes
a smaller bitstream buffer can be allocated. Since the bitstream buffer size now
depends on the format, replace CODA_MAX_FRAME_SIZE with ctx->bitstream.size
where appropriate and remove the now unused constant.
Since REQBUFS can be called multiple times, but the format can't be changed
unless REQBUFS 0 was called before, we can just keep the allocated context and
bitstream buffers if REQBUFS is called multiple times with a non-zero buffer
count.
[fixed a resource leak preventing repeatedly decoding]
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Allocate the per-context buffers from REQBUFS instead in start_encoding or
start_decoding. This allows to stop and start streaming independently of
buffer (re)allocation
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no need to take the detour through a "%s" format string
to create a copy of a string.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In coda_free_aux_buf() call debugfs_remove only if buffer entry
is valid (and therfore dentry is valid), double protect by
invalidating dentry value.
Fixes erroneous prematurely dealloc of debugfs caused by
incorrect reference count incrementing.
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We divide the bitrate by 1000 before writing it to the register.
Communicate to userspace that the bitrate granularity is kbps.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The s5p-mfc driver interprets a buffer with bytesused equal to 0 as a
special case indicating end-of-stream. After vb2: fix bytesused == 0
handling (8a75ffb) patch videobuf2 modified the value of bytesused if it
was 0. The allow_zero_bytesused flag was added to videobuf2 to keep
backward compatibility.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The coda driver interprets a buffer with bytesused equal to 0 as a special
case indicating end-of-stream. After vb2: fix bytesused == 0 handling
(8a75ffb) patch videobuf2 modified the value of bytesused if it was 0.
The allow_zero_bytesused flag was added to videobuf2 to keep
backward compatibility.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Don't rely on V4L2_DV_BT_STD_CEA861 since that include the
640x480p format, which is an IT format, not CE.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In addition to v4l2_find_dv_timings_cap(), where timings are searched
against the list of preset timings, the incoming timing from v4l2-ctl
is checked against CVT and GTF standards. If it confirms to be CVT or
GTF, it is treated as valid timing and vivid format is updated with
new timings.
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently vivid supports V4L2_DV_BT_STD_DMT and V4L2_DV_BT_STD_CEA861
discrete video standards. Extending the capability set to allow for
setting CVT and GTF standards. This change, along with adding the
support for calculating CVT, GTF timings in v4l2-ctl would extend
the number of resolutions supported by vivid to almost any custom
resolution.
Also extending the limits on min and max pixel clock to accommodate
pixel clock range provided by cvt/gtf for resolutions ranging from
640x360p50 to 4kx2Kp60.
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Removes some functions that are not used anywhere:
s5p_jpeg_input_raw_y16() s5p_jpeg_timer_disable() s5p_jpeg_timer_enable().
This was partially found by using a static code analysis program called
cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
JPEG codecs on Exynos4 and Exynos3250 SoCs utilize different number
of planes for storing the raw image data, depending on the format
of the image being processed. For the unused planes a random data
was being written to the related registers. Regardless of the fact
that this seemed not to be harmful, fix the issue for clarity reasons.
Reported-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
JPEG IP found in Exynos5420 is similar to what is in Exynos3250, but
there are some subtle differences which this patch takes into account.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The TPG generates multiple static or dynamic test patterns. The driver
currently hardcodes the pattern to the moving box pattern.
Signed-off-by: Christian Kohn <christian.kohn@xilinx.com>
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Video Timing Controller (VTC) includes a timing detector and/or a
timing generator. Only the generator is currently supported.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Xilinx platforms have no hardwired video capture or video processing
interface. Users create capture and memory to memory processing
pipelines in the FPGA fabric to suit their particular needs, by
instantiating video IP cores from a large library.
The Xilinx Video IP core is a framework that models a video pipeline
described in the device tree and expose the pipeline to userspace
through the media controller and V4L2 APIs.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radheys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While running v4l2-compliance tests on vivid I suddenly got errors due to
a call to vmalloc_user with size 0 from vb2.
Digging deeper into the cause I discovered that this was due to the fact that
struct v4l2_plane_pix_format defines bytesperline as a __u16 instead of a __u32.
The test I was running selected a format of 4 * 4096 by 4 * 2048 with a 32
bit pixelformat.
So bytesperline was 4 * 4 * 4096 = 65536, which becomes 0 in a __u16. And
bytesperline * height is suddenly 0 as well. While the vivid driver may be
a virtual driver, it is to be expected that this limit will be hit for real
hardware as well in the near future: 8k deep-color video will already reach
it.
The solution is to change the type to __u32. The only drivers besides vivid
that use the multiplanar API are little-endian ARM and SH platforms (exynos,
ti-vpe, vsp1), so this is safe.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Mistyping 0.2627 as 0.2726 I can understand, but -0.4598 as -0.4629? No idea how
I managed that. Anyway, these coefficients are now correct again.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Handle values like ~0 as width, height, left or top fields.
Just strip off the top 16 bits will ensure that the calculations
remain OK.
Found with v4l2-compliance.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The vivid driver reports a range of frame intervals for non-webcams, when in fact
the frame interval is fixed for those inputs as it depends on the DV timings or
standard. Just report the single discrete frame interval instead.
Caught by v4l2-compliance.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Allow setting the same timings as the current timings (i.e., do nothing in that
case). The code was actually there, but the vb2_is_busy() call was done before
the timings check instead of afterwards.
Found by v4l2-compliance.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the release callback of the v4l2_device to clean up the memory.
This prevents vivid from breaking if someone tries to unbind the
driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This turns this driver into a platform device. This ensures that it
appears in /sys/bus/platform_device since it now has a proper parent
device.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the packed YUV formats YUV444, YUV555, YUV565 and YUV32.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the four byte BGR666 format.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the one-byte-per-pixel RGB332 format.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the YUV 4:4:4 formats NV24 and NV42.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Only RGB555X was supported, add support for the other two variants.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Clarify which formats have an alpha channel and which do not by
using 'x' instead of 'a' if there is no alpha channel.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for (A/X)RGB444 formats.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Everything is in place to support these formats, so add them to
the list.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support in vivid for downsampling. Most of the changes are in
vivid_copy_buffer which needs to know about the right line widths.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make vivid aware of the difference of planes and buffers. Note that
this does not yet add support for hor/vert downsampled formats.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These fields are necessary to handle the new planar formats.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The last part of the vivid-tpg refactoring: split off the pattern
drawing code into a function of its own. This greatly improves the
readability and maintainability of this code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This moves the drawing code for the extras (border, square, etc) to
a function of its own instead of having this in the main for loop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Any parameters related to drawing 'extras' like the border, the square,
etc. are moved to struct tpg_draw_params.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a new function that fills in pattern-related fields in struct
tpg_draw_params.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace local variables by fields in the tpg_draw_params struct.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is needed to refactor the drawing function which is much too big.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Added 'const' to several functions where that is possible to do.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that the support for hor/vert downsampled planar formats is in
place we can add support for such formats to the TPG.
This patch adds support for:
V4L2_PIX_FMT_YUV420M
V4L2_PIX_FMT_YVU420M
V4L2_PIX_FMT_YUV420
V4L2_PIX_FMT_YVU420
V4L2_PIX_FMT_YUV422P
V4L2_PIX_FMT_NV16
V4L2_PIX_FMT_NV61
V4L2_PIX_FMT_NV12
V4L2_PIX_FMT_NV21
V4L2_PIX_FMT_NV12P
V4L2_PIX_FMT_NV21P
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement horizontal and vertical downsampling when filling in the
plane. The TPG is now ready to support such formats.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This will just skip lines/pixels since color fidelity is not quite
as important here as it is with the test patterns themselves.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
gen_twopix() is always called twice: once for the first and once for
the second pixel. Improve the code to properly average the two if the
format requires horizontal downsampling.
This is necessary for patterns like 1x1 red/blue checkers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When dealing with vertical downsampling two successive lines have to be
averaged. In the case of the test pattern generator that only happens
if the two lines are using different patterns. So precalculate the average
between two pattern lines: one of pattern P and one of pattern P + 1.
That way there is no need to do any on-the-fly downsampling: it's all done
in the precalculate phase.
This patch also implements horizontal downsampling in the precalculate phase.
The only thing that needs to be done is to half the width since the actual
downsampling happens when two pixels at a time are generated.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is step one of supporting horizontal and vertical downsampling.
This just adds support for the h/vdownsampling fields and it increases
the maximum number of planes to 3.
Currently none of the planar formats need horizontal or vertical
downsampling, so this change has no effect at the moment.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add helpers functions to determine the line widths and image sizes
for planar formats that are stores in a single buffer.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a new field that contains the number of buffers. This may be
less than the number of planes in case multiple planes are combined
into one buffer.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sequential top-bottom/bottom-top fields are not supported as video loopback.
This is too much work to implement for field settings that are rarely used.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The grayscale values are still full range sRGB, so don't add the
limited range offset.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a 2x2 checker patterns and 1x1 and 2x2 red/blue checker patterns.
Useful for testing 4:2:2 and 4:2:0 formats.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The successive TOP/BOTTOM fields did not move as they should: only
every other field actually changed position.
The cause was that the tpg needs to know if it is dealing with a
FIELD_ALTERNATE case since that requires slightly different handling.
So tell the TPG whether or not the field setting is for the ALTERNATE
case or not.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Two arrays of size 'max number of planes' have a hardcoded size instead
of using TPG_MAX_PLANES. Fix that, since TPG_MAX_PLANES will be increased
later on.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The condition to decide whether the current field is top or bottom
was inverted. Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The plane size check was hardcoded to plane 0 instead of using the plane
index.
This failed when using the NV61M format which has a larger plane size for
the second plane compared to the first plane.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the vivid driver is loaded in multiplanar mode, then the capture overlay
functionality should be disabled. This wasn't fully done, which led to
v4l2-compliance errors.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of forcing drivers to implement empty clock operations, make
them optional.
v4l2 clock registration in the soc-camera core should probably be
conditionned on the availability of those operations, but careful
review and/or testing of all drivers would be needed, so that should be
a separate step.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2 clock registered in soc_of_bind() must be unregistered if an
error occurs and makes the function fail.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
icd->control is the sub device dev, i.e. i2c device.
icd->pdev is the soc camera device's device.
To be consitent with power() function, we will call reset() with
icd->control as well.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All uses of the v4l2_clk API so far only register one clock with a fixed
name. This allows us to get rid of it, which also will make CCF and DT
integration easier.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed video_device struct (video_dev) in channel_obj and also the
Unregister path doesn't need to free the video_device structure,
hence, change the video_device.release callback point to
video_device_release_empty.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed video_device struct (video_dev) in channel_obj and also the
Unregister path doesn't need to free the video_device structure,
hence, change the video_device.release callback point to
video_device_release_empty.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed video_device struct (video_dev) in bcap_device and
Unregister path doesn't need to free the video_device
structure, hence, change the video_device.release callback
point to video_device_release_empty.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch adds support to set the v4l2 buffer sequence.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch adds support for VIDIOC_EXPBUF.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch adds support for VB2_DMABUF.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch adds support for vidioc_create_bufs.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch adds support to return -ENODATA for *dv_timings calls
if the current output does not support it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch adds supports to return -ENODATA to *_std calls
if the selected output does not support it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In start_streaming() callback the buffer is removed from the
dma_queue list and assigned to cur_frm, this patch makes sure
that is returned to vb2 core with VB2_BUF_STATE_ERROR flag.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch adds support to vb2_ioctl_* helpers.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch adds support to use v4l2_fh_open() and vb2_fop_release,
which allows to drop driver specific struct bcap_fh, as this is handled
by core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
No need to reinvent the wheel. Just use the already existing
functions provided by vb2.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch does the following:
a: returns -EINVAL in case format image size is less
then current image size.
b: assigns nbuffers to two in case the total of vq->num_buffers
and nbuffers is less then the number of buffers required by driver.
c: sets the sizes[0] of plane according to the fmt passed or which is
being set in the device.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
set the vb2 buffer field in buf_prepare() callback,
alongside drop local variable buf as we already have
a pointer to vb2 buffer.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch sets the min_buffers_needed field of the vb2 queue
so that the vb2 core will make sure start_streaming() callback
is called only when we have minimum buffers queued.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch adds support to release the buffer by calling
vb2_buffer_done(), with state marked as VB2_BUF_STATE_QUEUED
if start_streaming() call back fails.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch drops the buf_init() callback as init
of buf list is not required.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
According to the standard the R'G'B' BT.2020 colorspace is limited
range, not full range. Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed video_device struct (video_dev) in vpfe_device and
Unregister path doesn't need to free the video_device
structure, hence, change the video_device.release callback
point to video_device_release_empty.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of matching the subdevs with their name, match
it with OF node/ i2c address and adapter number.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Check for dev_fmt being null before derefrencing it, to assign it
to planes.
Found using Coccinelle.
Signed-off-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The remote port reference is released both at the end of the OF graph
parsing loop, and in the error code path at the end of the function.
Those two calls will release the same reference, causing the reference
count to go negative.
Fix the problem by removing the second call.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Unsigned int cannot be used to store casted pointer on 64bit
architecture, so correct such casts to properly use unsigned long
variables.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
[k.debski@samsung.com: removed volatile and __iomem from cast]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
TASK_SIZE is depends on the systems architecture (32 or 64 bits) and it
should not be used for defining offset boundary for mmaping buffers for
CAPTURE and OUTPUT queues. This patch fixes support for MMAP calls on
the CAPTURE queue on 64bit architectures (like ARM64).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Print a warning when the driver is used with platform data. Existing
platform data users should move to DT now.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the ISP device to omap3 DT include file and add support to the driver to
use it.
Also obtain information on the external entities and the ISP configuration
related to them through the Device Tree in addition to the platform data.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The omap3isp MMIO register block is contiguous in the MMIO register space
apart from the fact that the ISP IOMMU register block is in the middle of
the area. Ioremap it at two occasions, and keep the rest of the layout of
the register space internal to the omap3isp driver.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The syscon register isn't part of the ISP, use it through the syscom driver
regmap instead. The syscom block is considered to be from 343x on ISP
revision 2.0 whereas 15.0 is assumed to have 3630 syscon.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Only the histogram sub-block driver uses the physical address. Do not store
it for other sub-blocks.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The video port clock is l3_ick divided by vpclk_div. This clock must be high
enough for the external pixel rate. The video port requires two clock cycles
to process a pixel.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make omap3isp configuration data structures more suitable for consumption by
the DT by separating the I2C bus information of all the sub-devices in a
group and the ISP bus information from each other. The ISP bus information
is made a pointer instead of being directly embedded in the struct.
In the case of the DT only the sensor specific information on the ISP bus
configuration is retained. The structs are renamed to reflect that.
After this change the structs needed to describe device configuration can be
allocated and accessed separately without those needed only in the case of
platform data. The platform data related structs can be later removed once
the support for platform data can be removed.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Igor Grinberg <grinberg@compulab.co.il> (for cm-t35)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Only check for call platform data callback functions if there's platform
data. Also take care of a few other cases where the NULL pdata pointer could
have been accessed, and remove the check for NULL dev->platform_data
pointer.
Removing the check for NULL dev->platform_data isn't strictly needed by the
DT support but there's no harm from that either: the device now can be used
without sensors, for instance.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move the code which connects the external entity to an ISP entity into a
separate function. This disconnects it from parsing the platform data.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If an uninitialised v4l2_subdev struct was passed to
media_entity_create_link(), one of the BUG_ON()'s in the function will be
hit since media_entity.num_pads will be zero. Avoid this by checking whether
the num_pads field is non-zero for the interface.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The mutex was not destroyed correctly if dma_coerce_mask_and_coherent()
failed for some reason.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace the custom OMAP DMA API usage by DMA engine. Feature-wise the
driver has lost the ability to get notified of DMA transfers failure
through the completion handler, as the DMA engine API doesn't expose
that status information.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace the open-coded copy by a function call.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There isn't a need to assign the state of vb2_buffer to active
as this is already done by the core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
videobuf2 has long been subject to AB-BA style deadlocks due to the
queue lock and mmap_sem being taken in different orders for the mmap
operation. The problem has been fixed by making this operation callable
without taking the queue lock, using an mmap_lock internal to videobuf2.
The omap3isp driver still calls the mmap operation with the queue lock
held, resulting in a potential deadlock. As the operation can now be
called without locking the queue, fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Unsigned int cannot be used to store casted pointer on 64bit
architecture, so correct such casts to properly use unsigned long
variables.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
[k.debski@samsung.com: removed volatile and __iomem from cast]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
TASK_SIZE is depends on the systems architecture (32 or 64 bits) and it
should not be used for defining offset boundary for mmaping buffers for
CAPTURE and OUTPUT queues. This patch fixes support for MMAP calls on
the CAPTURE queue on 64bit architectures (like ARM64).
Cc: stable@vger.kernel.org
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_dev field of struct video_device must be set correctly.
This was never done for this driver, so no video nodes were created
anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v3.11 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support the new 'which' field in the enum_frame_interval ops. Most drivers do not
need to be changed since they always returns the same enumeration regardless
of the 'which' field.
Tested for ov7670 and marvell-ccic on a OLPC XO-1 laptop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support the new 'which' field in the enum_frame_size ops. Most drivers do not
need to be changed since they always returns the same enumeration regardless
of the 'which' field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support the new 'which' field in the enum_mbus_code ops. Most drivers do not
need to be changed since they always return the same enumeration regardless
of the 'which' field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If a subdevice pad op is called from a bridge driver, then there is
no v4l2_subdev_fh struct that can be passed to the subdevice. This
made it hard to use such subdevs from a bridge driver.
This patch replaces the v4l2_subdev_fh pointer by a v4l2_subdev_pad_config
pointer in the pad ops. This allows bridge drivers to use the various
try_ pad ops by creating a v4l2_subdev_pad_config struct and passing it
along to the pad op.
The v4l2_subdev_get_try_* macros had to be changed because of this, so
I also took the opportunity to use the full name of the v4l2_subdev_get_try_*
functions in the __V4L2_SUBDEV_MK_GET_TRY macro arguments: if you now do
'git grep v4l2_subdev_get_try_format' you will actually find the header
where it is defined.
One remark regarding the drivers/staging/media/davinci_vpfe patches: the
*_init_formats() functions assumed that fh could be NULL. However, that's
not true for this driver, it's always set. This is almost certainly a copy
and paste from the omap3isp driver. I've updated the code to reflect the
fact that fh is never NULL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The patch "media: s5p-mfc: use vb2_ops_wait_prepare/finish helper"
(654a731be1) introduced a kernel panic.
The q->lock was set for just one queue, the other was not set thus causing
a NULL pointer dereference.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fabien Dessenne