All chips of i.mx6 can be powered off by programming SNVS.
For example :
On i.mx6q-sabresd board, PMIC_ON_REQ connect with external
pmic ON/OFF pin, that will cause the whole PMIC powered off
except VSNVS. And system can restart once PMIC_ON_REQ goes
high by push POWRER key.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds links to the on-chip SRAM and reset controller nodes
and switches the interrupts. Make the BIT processor interrupt, which exists on
all variants, the first one. The JPEG unit interrupt, which does not exist on
i.MX27 and i.MX5 thus is an optional second interrupt.
Use different compatible strings for i.MX6Q/D and i.MX6S/DL, as they have to
load separate firmware images for some reason.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Original gpt per clk parent is from ipg_per clk which
may be scaled when system enter low bus mode, as ipg
clk will be lower in low bus mode, to keep system clk
NOT drift, select gpt per clk parent from OSC which
is at fixed freq always.
On i.mx6qdl, add a osc_per clk source for i.mx6q
TO > 1.0 and all i.MX6dl SoC.
On i.mx6sx, just make gpt per clk from OSC.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Baud clock is used for bit clock generation in master mode. Ipg clock
is peripheral clock and peripheral access clock.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fixes "imx6q-pcie 1ffc000.pcie: missing *config* reg space"
error exposed by new versions of the designware pcie driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds simple-card support to the i.MX SoCs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Since commit 98ea6ad2ed (ARM: dts: imx6: use imx51-ssi) the mx6 ssi is
compatible with imx51, so align all the mx6 variant ssi compatible strings as:
compatible = "fsl,<imx6-soc>-ssi", "fsl,imx51-ssi";
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
When booting a board that does not have a keypad (such as imx6q-sabresd) the
following error is seen on boot:
imx-keypad 20b8000.kpp: OF: linux,keymap property not defined in /soc/aips-bus@02000000/kpp@020b8000
imx-keypad 20b8000.kpp: failed to build keymap
imx-keypad: probe of 20b8000.kpp failed with error -2
Let's disable the keypad functionality in the dtsi files and let each board dts
enable it when needed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
All dtsi files where already moved to generic dma bindings. Remove the
old non-generic DMA properties.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The S/PDIF rxtx4 and rxtx6 clock inputs are "ESAI_HCKT" and "MLB clock",
respectively, according to the SoC documentation, and they are currently
mapped to clocks "esai" and "mlb".
However, they do not seem to actually work correctly. Testing on a
Cubox-i system with fsl_spdif driver forced to select one of those as
input will result in I/O errors on audio playback, which I believe means
missing clock signal.
Possibly the "ESAI_HCKT" and "MLB clock" refer to some other clocks
related to ESAI and MLB, or we are missing something else.
Since audio playback will not work if fsl_spdif selects these clocks
(which happens rarely), set the inputs do dummy clocks, at least for
now.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The rxtx2 clock of i.MX6 S/PDIF is currently set to "asrc" clock.
However, according to SoC documentation, rxtx2 is connected to
ASRC_EXT_CLK, a different external clock.
Testing on Cubox-i system seems to confirm that: when fsl_spdif is
forced to select rxtx2 as input clock, audio playback fails with an I/O
error.
Set rxtx2 to the dummy clock by default to prevent fsl_spdif from
selecting it.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds CSI subnodes for IPU1 and IPU2 that will contain
ports and endpoints connecting to external elements in the video
pipeline.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The new bindings drops one clock, renames the others and
drops the old interrupt mapping.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add alias for FEC ethernet on i.MX to allow bootloaders (like U-Boot)
patch-in the MAC address for FEC using this alias.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Per bindings of fixed-clock, #clock-cells is a required property. Let's
add it for those fixed rate clocks.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Those two properties should have been set to zero, which
is the same as not specifying them.
Having address-cells set to 1 causes OF interrupt
mapping routines to add 1 to the interrupt-cells
property and as result fail because all calculations
are off by one.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
As defined by the common PCI bindings.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
A large part of the arm-soc patches are nowadays DT changes, adding support
for new SoCs, boards and devices without changing kernel source. The plan
is still to move the devicetree files out of the kernel tree and reduce
the amount of churn going on here, but we keep finding reasons to delay
doing that.
Changes are really all over the place, with little sticking out particularly.
We have contributions from a total of 116 people in this branch.
Unfortunately, the size of this branch also causes a significant number
of conflicts at the moment, typically when subsystem maintainers merge
patches that change the driver at the same time as the dts files. In
most cases this could be avoided because the dts changes are supposed
to be compatible in both ways, and we are asking everyone to send ARM
dts changes through our tree only.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=zl/N
-----END PGP SIGNATURE-----
Merge tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"A large part of the arm-soc patches are nowadays DT changes, adding
support for new SoCs, boards and devices without changing kernel
source. The plan is still to move the devicetree files out of the
kernel tree and reduce the amount of churn going on here, but we keep
finding reasons to delay doing that.
Changes are really all over the place, with little sticking out
particularly. We have contributions from a total of 116 people in
this branch.
Unfortunately, the size of this branch also causes a significant
number of conflicts at the moment, typically when subsystem
maintainers merge patches that change the driver at the same time as
the dts files. In most cases this could be avoided because the dts
changes are supposed to be compatible in both ways, and we are asking
everyone to send ARM dts changes through our tree only"
* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
dts: stmmac: Document the clocks property in the stmmac base document
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
ARM: STi: stih416: Add support for the FSM Serial Flash Controller
ARM: tegra: fix Dalmore pinctrl configuration
ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
ARM: dts: Build all keystone dt blobs
ARM: dts: keystone: Fix control register range for clktsip
ARM: dts: keystone: Fix domain register range for clkfftc1
ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
ARM: dts: bcm21664: Add device tree files.
ARM: DT: bcm21664: Device tree bindings
ARM: efm32: properly namespace i2c location property
ARM: efm32: fix unit address part in USART2 device nodes' names
ARM: mvebu: Enable NAND controller in Armada 385-DB
ARM: mvebu: Add support for NAND controller in Armada 38x SoC
ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
...
This patch connects IPU and display encoder (HDMI, LVDS, MIPI)
device tree nodes, as well as parallel displays on the DISP0
and DISP1 outputs, using the OF graph bindings described in
Documentation/devicetree/bindings/media/video-interfaces.txt
The IPU ports correspond to the two display interfaces. The
order of endpoints in the ports is arbitrary.
Each encoder with an associated input multiplexer has multiple
input ports in the device tree. The order and reg property of
the ports must correspond to the multiplexer input order.
Since the imx-drm node now only needs to contain links to the
display interfaces, it can be moved to the SoC dtsi level. At
the board level, only connections between the display interface
ports and encoders or panels have to be added.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Extracted from another patch by Fabio Estevam, this adds the DT
configuration for HDMI output on the IMX6 SoCs
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
imx51-ssi and imx21-ssi are different IPs. imx51-ssi supports online
reconfiguration and needs this for correct interaction with SDMA. This
patch adds imx51-ssi before each imx21-ssi for all imx6 SoCs.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
We need to use controller id to access different register regions
for mxs phy.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
We need to be able to override interrupts in board file to
workaround a hardware bug for ethernet interrupts
waking the processor by using interrupts-extended.
So, use interrupts-extended here as well.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Instead of calling the regulator for the ARM core as 'cpu', let's rename it
as 'vddarm', so that we keep a better consistency with the other internal
regulators:
vdd1p1: 800 <--> 1375 mV at 1100 mV
vdd3p0: 2800 <--> 3150 mV at 3000 mV
vdd2p5: 2000 <--> 2750 mV at 2400 mV
vddarm: 725 <--> 1450 mV at 1150 mV
vddpu: 725 <--> 1450 mV at 1150 mV
vddsoc: 725 <--> 1450 mV at 1200 mV
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Thermal sensor needs pll3_usb_otg when measuring temperature,
so we need to pass clk info to thermal driver.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Make the interrupts node slightly more readable.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that
boards that share the same pinctrl setting do not have to define it time
and time again in <board>.dts. However, along with the devices and use
cases being added continuously, the pinctrl setting nodes under iomuxc
becomes more than expected. This bloats device tree blob for particular
board unnecessarily since only a small subset of those pinctrl setting
nodes will be used by the board. It impacts not only the DTB file size
but also the run-time device tree lookup efficiency.
The patch moves all the pinctrl data into individual boards as needed.
With the changes, the pinctrl setting nodes becomes local to particular
board, and it makes no sense to continue numbering the setting for
given peripheral. Thus, all the pinctrl phandler name gets updated to
have only peripheral name in there.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Typically nodes are disabled by default and enabled when needed.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The spdif "rxtx5" clock option is being set to ipg clk (62) by mistake.
This causes an incorrect time keeping when spdif driver is running,
because ipg is ancestor clock for clocksource while spdif driver will
change the rate of this clock in certain circumstance. Before the
correct clock for "rxtx5" option can be supplied, let's disable this
option for now by filling a dummy clock for it.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This is needed for supporting ultra high speed cards like SD3.0 cards.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The ocram on imx6q is 256 KiB while on imx6dl it's 128 KiB. Let's
have separate node for imx6q and imx6dl. It also changes imx6q size
0x3f000 to 0x40000 to match the hardware.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Liu Ying <Ying.Liu@freescale.com>
After mxs-dma driver adopts generic DMA device tree binding, gpmi
channel interrupt number is defined in DMA controller node, and
channel ID is listed in "dmas" property. So the DMA channel interrupt
number in gpmi node "interrupts" property and fsl,gpmi-dma-channel which
are used by old customized DMA binding can be removed now.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Add the dma property for all the uart.
Note: Add the dma property does not mean we enable the dma for this
uart.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add the a new pinctrl for uart3. In the imx6q{dl}-sabreauto boards,
the uart3 is used for Bluetooth.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add more imx6q/dl pin groups for those supported boards, e.g. sabresd,
sabreauto, arm2.
IPU2 pin groups are added into imx6q.dtsi, since the block is only
available on imx6q.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The imx6q and imx6dl are two pin-to-pin compatible SoCs. The same board
design can work with either chip plugged into the socket, e.g. sabresd
and sabreauto boards.
We currently define pin groups in imx6q.dtsi and imx6dl.dtsi
respectively because the pad macro names are different between two
chips. This brings a maintenance burden on having the same label point
to the same pin group defined in two places.
The patch replaces prefix MX6Q_ and MX6DL_ with MX6QDL_ for both SoCs
pad macro names. Then the pin groups becomes completely common between
imx6q and imx6dl and can just be moved into imx6qdl.dtsi, so that the
long term maintenance of imx6q/dt pin settings becomes easier.
Unfortunately, the change brings some dramatic diff stat, but it's all
about DTS file, and the ultimate net diff stat is good.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Robin Gong