Make sure to drop the references taken by of_parse_phandle() and
bus_find_device() before returning from am335x_get_phy_control().
Note that there is no guarantee that the devres-managed struct
phy_control will be valid for the lifetime of the sibling phy device
regardless of this change.
Fixes: 3bb869c8b3 ("usb: phy: Add AM335x PHY driver")
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Properly check the return code of ffs_func_revmap_intf() and
ffs_func_revmap_ep() for a non-negative value.
Instead of checking the return code, the comparison was performed for the last
parameter of the function calls, because of wrong parenthesis.
This also fixes the following static checker warning:
drivers/usb/gadget/function/f_fs.c:3152 ffs_func_req_match()
warn: always true condition '(((creq->wIndex)) >= 0) => (0-u16max >= 0)'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Hädicke <felixhaedicke@web.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
USB-3 does not have any link state that will avoid negotiating a connection
with a plugged-in cable but will signal the host when the cable is
unplugged.
For USB-3 we used to first set the link to Disabled, then to RxDdetect to
be able to detect cable connects or disconnects. But in RxDetect the
connected device is detected again and eventually enabled.
Instead set the link into U3 and disable remote wakeups for the device.
This is what Windows does, and what Alan Stern suggested.
Cc: stable@vger.kernel.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This already gets done automatically by PM runtime and we have
a separate autosuspend timeout in musb_core.c.
Reviewed-by: Johan Hovold <johan@kernel.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are missing pm_runtime_disable() in 2430 glue layer. Further,
we only need to enable PM runtime and disable it on exit. With
musb_core.c doing PM, the glue layer as a parent will always be
active when musb_core.c is active.
This fixes host enumeration issues with some devices as reported
by Ladislav Michl <ladis@linux-mips.org>.
And holding an RPM reference while deregistering the child would
lead to a crash in omap2430_runtime_suspend() which dereferences
the now freed child's driver data on put as pointed out by
Johan Hovold <johan@kernel.org>:
Unable to handle kernel paging request at virtual address 6b6b6f17
...
[<c05453d4>] (omap2430_runtime_suspend) from [<c0481410>]
(pm_generic_runtime_suspend+0x3c/0x48)
[<c0481410>] (pm_generic_runtime_suspend) from [<c0121028>]
(_od_runtime_suspend+0x1c/0x30)
[<c0121028>] (_od_runtime_suspend) from [<c04833b0>] (__rpm_callback+0x3c/0x70)
[<c04833b0>] (__rpm_callback) from [<c0483414>] (rpm_callback+0x30/0x90)
[<c0483414>] (rpm_callback) from [<c0483984>] (rpm_suspend+0x118/0x6b4)
[<c0483984>] (rpm_suspend) from [<c04840f4>] (rpm_idle+0x104/0x440)
[<c04840f4>] (rpm_idle) from [<c04844ac>] (__pm_runtime_idle+0x7c/0xb0)
[<c04844ac>] (__pm_runtime_idle) from [<c0545458>] (omap2430_remove+0x38/0x58)
[<c0545458>] (omap2430_remove) from [<c047b2bc>] (platform_drv_remove+0x34/0x4c)
Note that if changes are needed to the autosuspend timeout, it should
be done in musb_core.c.
Reported-by: Ladislav Michl <ladis@linux-mips.org>
Fixes: 87326e8584 ("usb: musb: Remove extra PM runtime calls from
2430 glue layer")
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With a USB hub disconnected, devctl can be 0x19 for about a second
on am335x and will stay forever on at least omap3. And we get no
further interrupts when devctl session bit clears. This keeps
PM runtime active.
Let's fix the issue by polling devctl until the session bit clears
or times out. We can do this by making musb->irq_work into
delayed_work.
And with the polling implemented, we can now also have the quirk
for invalid VBUS it to avoid disconnecting too early while VBUS
is ramping up.
Fixes: 467d5c9807 ("usb: musb: Implement session bit based runtime
PM for musb-core")
Fixes: 65b3f50ed6 ("usb: musb: Add PM runtime support for MUSB DSPS
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 65b3f50ed6 ("usb: musb: Add PM runtime support for MUSB DSPS
glue layer") wrongly added a call for pm_runtime_get_sync to otg_timer
that runs in softirq context. That causes a "BUG: sleeping function called
from invalid context" every time when polling the cable status:
[<c015ebb4>] (__might_sleep) from [<c0413d60>] (__pm_runtime_resume+0x9c/0xa0)
[<c0413d60>] (__pm_runtime_resume) from [<c04d0bc4>] (otg_timer+0x3c/0x254)
[<c04d0bc4>] (otg_timer) from [<c0191180>] (call_timer_fn+0xfc/0x41c)
[<c0191180>] (call_timer_fn) from [<c01915c0>] (expire_timers+0x120/0x210)
[<c01915c0>] (expire_timers) from [<c0191acc>] (run_timer_softirq+0xa4/0xdc)
[<c0191acc>] (run_timer_softirq) from [<c010168c>] (__do_softirq+0x12c/0x594)
I did not notice that as I did not have CONFIG_DEBUG_ATOMIC_SLEEP enabled.
And looks like also musb_gadget_queue() suffers from the same problem.
Let's fix the issue by using a list of delayed work then call it on
resume. Note that we want to do this only when musb core and it's
parent devices are awake, and we need to make sure the DSPS glue
timer is stopped as noted by Johan Hovold <johan@kernel.org>.
Note that we already are re-enabling the timer with mod_timer() in
dsps_musb_enable().
Later on we may be able to remove other delayed work in the musb driver
and just do it from pending_resume_work. But this should be done only
for delayed work that does not have other timing requirements beyond
just being run on resume.
Fixes: 65b3f50ed6 ("usb: musb: Add PM runtime support for MUSB DSPS
glue layer")
Reported-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't use static variable first for checking when musb is
initialized when we have multiple musb instances like on am335x.
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BRIM Brothers Zone DPMX is a bicycle powermeter. This ID is for the USB
serial interface in its charging dock for the control pods, via which some
settings for the pods can be modified.
Signed-off-by: Paul Jakma <paul@jakma.org>
Cc: Barry Redmond <barry@brimbrothers.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Some code (all error handling) submits CDBs that are allocated
on the stack. This breaks with CB/CBI code that tries to create
URB directly from SCSI command buffer - which happens to be in
vmalloced memory with vmalloced kernel stacks.
Let's make copy of the command in usb_stor_CB_transport.
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We normally use the passed in gfp flags for allocations, it's just these
two which were missed.
Fixes: 22d45f01a8 ("usb/xhci: replace pci_*_consistent() with dma_*_coherent()")
Cc: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only user of the functions mtu3_irq() and gpd_ring_empty() are in
the same file. They can be declared as static.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci->slot_id is used for providing a way to pass slot id from the
command completion handler to the function waiting for completion.
It's shared by enumerations of all USB devices connected to an
xhci host. Hence, it's a source for possible races. Since we've
introduced command structure and the command queue to xhci driver.
It's better to move slot_id from xhci_hcd structure to xhci_command
structure. Hence the race source is removed.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci->addr_dev is used for the completion of both address device
and enable slot commands. It's shared by enumerations of all USB
devices connected to an xhci host. Hence, it's just a source for
possible races. Since we've introduced command structure and the
command queue to xhci driver. It is time to get rid of addr_dev
and use the completion in the command structure instead.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cmd_completion in struct xhci_virt_device is legacy. With command
structure and command queue introduced in xhci, cmd_completion is
not used any more. This patch removes it.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
define GET_EP_CTX_STATE() macro to get the endpoint state from a
pointer to a le32 enpoint context structure
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for Renesas r8a7796 SoC. This SoC is not
compatible with r8a7795 because using firmware version differs.
Since the "V2" firmware can be used on both r8a7795 (es1.x) and r8a7796,
the "renesas,rcar-gen3-xhci" keeps to use the "V2" for now.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a new firmware version "V3" for r8a7796. This patch
also adds explanation of each version's information.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In xhci_handle_event(), when errors are detected, driver always sets
a bit in error_bitmask (one member of the xhci private driver data).
That means users have to retrieve and decode the value of error_bitmask
in xhci private driver data if they want to know whether those erros
ever happened in xhci_handle_event(). Otherwise, those errors are just
ignored silently.
This patch cleans up this by replacing the setting of error_bitmask
with the kernel print functions, so that users can easily check and
report the errors happened in xhci_handle_event().
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want one function that gives back urb in interrupt that can
be used in both normal cases and when killing off urbs.
Add small helpers that check if td is last_td_in_urb() and
that increase the td count of a urb inc_td_cnt()
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mostly refactoring and code cleanup.
while handling transfer events we used to check the return value of
various functions to see if we can give back the URB.
Turns out the only case when those return values are set are when
finish_td() notices we are completing the last td in the URB.
give back the urb directly in finish_td() instead.
Only functional change is that we now increase the event ring dequeue
pointer in sowtware after giving back the URB. This should not matter
as we are in hardware interrupt context and the time when writing the
new event ring dequeue to hardware remains the same.
Hardware is the only one that can put event TRBs on the event ring.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move giving back the urb to a separate function
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following sparse warning:
drivers/usb/host/xhci-ring.c:608:6: warning:
symbol 'xhci_unmap_td_bounce_buffer' was not declared.
Should it be static?
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No functional changes but a few debugging outputs removed
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Renaming variables, no functional changes
Event trbs on the event ring cointain a pointer to the transfer trb
on a endpoint ring that caused the event.
The naming has been very confusing as the event trb was called "event"
and the endpoint transfer trb was called "event_trb".
rename all variables that are realated to the endpoint transfer trb
from event_* to ep_*
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mostly refactoring, but does also change error message if
we get a bad length in the event trb.
Adds a helper function to sum trb lengths of partial TDs
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor pricess_ctrl_tx() to make it more readable
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only check for the URB_SHORT_NOT_OK urb flag to set the urb status
to -EREMOTEIO for transfers that didn't transfer all data.
This will be done in __usb_hcd_giveback() for other than isoc tranfers,
so remove the redundant check from xhci.
Also fix a couple split lines in debug messages to make them greppable.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
replace the complex check for noop with a simple helper
Improve code readability
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the trb_is_link() and link_trb_toggles_cycle() helpers to
make the code more readable
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point in trying to reset the host controller by writing
to its registers if host is removed and registers just return 0xffffffff
bail out and return -ENODEV instead
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old error message always stated that host was not halted
even after trying a certain time.
Host may fail the halt immediately as well with -ENODEV if device
is removed and returns 0xffffffff.
Use a more generic error message and show return value to know if we
failed with -ETIMEDOUT or -ENODEV
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fist function called in xhci_halt is xhci_quiesce, so no point
in calling it twice
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The internal 60Mhz clock for host2 and host3 are useless in ULPI
phy mode, so we disable it when configuring ULPI PHY node for
those host.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
In order to use ULPI phy with usb host 2 and 3, we need to configure
controller register to enable ULPI features.
Each USB controller have different behaviour, so in order to avoid to have
several "swicth(data->index)" and lock/unlock, we prefer to get the index
switch and then test for features if they exist for this index.
This patch also remove useless test of reg and val. Those two values cannot
be NULL.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The DMA descriptors are little endian, and we do a pretty good
job of handling them with the proper le32_to_cpu() markings, but
we don't actually mark them as __le32. This means checkers like
sparse can't easily find new bugs. Let's mark the members of
structures properly and fix the few places where we're missing
conversions.
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The UHCI controllers in Intel chipsets rely on a platform-specific non-PME
mechanism for wakeup signalling. They can generate wakeup signals even
though they don't support PME.
We need to let the USB core know this so that it will enable runtime
suspend for UHCI controllers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: stable@vger.kernel.org
Drop invalid user-pointer checks from ioctl handlers.
A NULL-pointer can be valid in user space and copy_to_user() takes care
of sanity checking.
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the tty get_icount operation instead of implementing TIOCGICOUNT
directly.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop invalid user-pointer check from TIOCGSERIAL handler.
A NULL-pointer can be valid in user space and copy_to_user() takes care
of sanity checking.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TIOCMIWAIT implementation would return -EINVAL if any of the three
supported signals were included in the mask.
Instead of returning an error in case TIOCM_CTS is included, simply
drop the mask check completely, which is in accordance with how other
drivers implement this ioctl.
Fixes: 5a6a62bdb9 ("cdc-acm: add TIOCMIWAIT")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add super speed descriptors to f_hid.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The patch improves readability of mv_u3d_start_queue()
by rearranging its code with two semantic modifications:
- assignment zero to ep->processing if usb_gadget_map_request() fails;
- propagation of error code from mv_u3d_req_to_trb() instead of
hardcoded -ENOMEM.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
mv_u3d_req_to_trb() does not check for dma mapping errors.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Finally get rid of dwc3_trace() hack. If any other
message is truly needed, we should add proper
tracepoints for them instead of hacking around with
dwc3_trace() or similar.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of using a simple trace_printk() wrapper,
let's add an actual tracepoint and print further
details about the endpoint being operated upon.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for the TI CC3200 LaunchPad board, which uses a
custom USB vendor ID and product ID. Channel A is used for JTAG, and
channel B is used for a UART.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
usb-storage does not use any freezer apis, so drop the inclusion of
freezer.h from the drivers/usb/storage/usb.c file.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use DEVICE_ATTR_RW for read-write attributes. This simplifies the
source code, improves readbility, and reduces the chance of
inconsistencies.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@rw@
declarer name DEVICE_ATTR;
identifier x,x_show,x_store;
@@
DEVICE_ATTR(x, \(0644\|S_IRUGO|S_IWUSR\), x_show, x_store);
@script:ocaml@
x << rw.x;
x_show << rw.x_show;
x_store << rw.x_store;
@@
if not (x^"_show" = x_show && x^"_store" = x_store)
then Coccilib.include_match false
@@
declarer name DEVICE_ATTR_RW;
identifier rw.x,rw.x_show,rw.x_store;
@@
- DEVICE_ATTR(x, \(0644\|S_IRUGO|S_IWUSR\), x_show, x_store);
+ DEVICE_ATTR_RW(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use DEVICE_ATTR_WO for write ony attributes and DEVICE_ATTR_RO for read
only attributes. This simplifies the source code, improves readbility,
and reduces the chance of inconsistencies.
The semantic patch for the RO case is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@ro@
declarer name DEVICE_ATTR;
identifier x,x_show;
@@
DEVICE_ATTR(x, \(0444\|S_IRUGO\), x_show, NULL);
@script:ocaml@
x << ro.x;
x_show << ro.x_show;
@@
if not (x^"_show" = x_show) then Coccilib.include_match false
@@
declarer name DEVICE_ATTR_RO;
identifier ro.x,ro.x_show;
@@
- DEVICE_ATTR(x, \(0444\|S_IRUGO\), x_show, NULL);
+ DEVICE_ATTR_RO(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes possibility of dereference by NULLL pointer in "[PATCH
v5 1/3] usbip: vhci extension: modifications to vhci driver" which has
been merged to 4.9-rc1. It occurs when a URB with pointer to invalid
USB/IP device is enqueued in race condition against detach operation.
A pointer was passed to vdev_to_vhci() before NULL check.
In vdev_to_vhci(), there's a dereference by the pointer.
This patch moves vdev_to_vhci() after NULL check of the pointer.
Signed-off-by: Nobuo Iwata <nobuo.iwata@fujixerox.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
variable struct usb_cdc_parsed_header h may be used
uninitialized in acm_probe.
In kernel 4.8.
/* handle quirks deadly to normal probing*/
if (quirks == NO_UNION_NORMAL)
...
goto skip_normal_probe;
}
we bypass call to
cdc_parse_cdc_header(&h, intf, buffer, buflen);
but later use h in
if (h.usb_cdc_country_functional_desc) { /* export the country data */
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Reported-by: Victor Sologoubov <victor0@rambler.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Never seen XHCI auto handoff working on TI and RENESAS cards.
Eventually, we force handoff. This code forces the handoff
unconditionally. It saves 5 seconds boot time for each card.
Signed-off-by: Babu Moger <babu.moger@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This suppresses printing the error message "failed to get phy" in the
kernel log when the error is -EPROBE_DEFER. This prevents usless noise
in the kernel log.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel's BXT devices need to execute a _DSM method
during {runtime_,}{suspend,resume} in order to get a
chunk of dwc3 to power gate and save some extra
power.
Let's do that now.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We'll be tracking a little more information for PCI
drivers, it's about time we add a private structure
for that.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When we get a half-way processed request, we should
make sure to try to prepare further TRBs for it or
for any possibly queued up request held in our
pending_list. This will make sure our controller is
kept busy for as long as possible.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Say we have three requests prepared to the HW (reqA,
reqB, and reqC). All of them are composed of
SG-lists with several entries and they all requests
interrupt only on last TRBs of the SG-list.
When we get interrupt for reqA, it could be that
reqB is already half-way transferred and some of its
TRBs will have HWO already cleared.
It's okay to free up TRBs without HWO bit set, but
we need to guarantee we don't giveback a request
that's half-way transferred as that will confuse
gadget drivers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In cases where we're given an SG-list which is
longer than the amount of currently available TRBs,
we will be left with the same request on
started_list and we should prioritize that request
over possible new requests on pending_list. That's
a way to guarantee requests complete in order.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This will give us a simpler way of figuring out how
many bytes were left in each TRB. It's useful for
cases where we queue only part of an SG-list due to
amount of available TRBs at the time of kicking the
transfer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If XferNotReady comes before usb_ep_queue() we will
set our PENDING request flag and wait for a
request. However, originally, we were assuming
usb_ep_queue() would always happen before our first
XferNotReady and that causes a corner case where we
could try to issue ENDTRANSFER command before
STARTTRANSFER.
Let's fix that by tracking endpoints which have been
started.
Reported-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of just delaying for 100us, we should
actually wait for End Transfer Command Complete
interrupt before moving on. Note that this should
only be done if we're dealing with one of the core
revisions that actually require the interrupt before
moving on.
[ felipe.balbi@linux.intel.com: minor improvements ]
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dev_kfree_skb_any() is used to free packets that are dropped by the
network stack. Therefore the function should not be used for packets
that have been successfully processed by the network stack. Instead
dev_consume_skb_any() has to be used for such consumed packets.
This separation helps to identify dropped packets.
Signed-off-by: Torsten Polle <tpolle@de.adit-jv.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Socket buffers should be linked to the (network) device that allocated
the buffers. __netdev_alloc_skb performs this task.
Signed-off-by: Torsten Polle <tpolle@de.adit-jv.com>
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Socket buffers should be linked to the (network) device that allocated
the buffers.
Signed-off-by: Torsten Polle <tpolle@de.adit-jv.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
waiter context waker context
reinit_completion()
usb_esp_queue()
wait_for_completion_interruptible()
ffs_ep0_complete()
complete()
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The combo of list_empty() check and return list_first_entry()
can be replaced with list_first_entry_or_null().
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The combo of list_empty() check and return list_first_entry()
can be replaced with list_first_entry_or_null().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The combo of list_empty() check and return list_first_entry()
can be replaced with list_first_entry_or_null().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use the more common logging mechanism.
Miscellanea:
o Realign multiline statements
o Coalesce format
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When we change the USB function with configfs dynamically, we possibly
met this situation: one core is doing the control transfer, another core
is trying to unregister the USB gadget from userspace, we must wait for
completing this control tranfer, or it will hang the controller to set
the DEVCTRLHLT flag.
[ felipe.balbi@linux.intel.com: several fixes to the patch
- call complete() before starting following SETUP transfer
- add a macro for ep0_in_setup's timeout
- change commit subject slightly
- break lines at 72 characters (git adds an 8-character tab)
- avoid changes to dwc3_gadget_run_stop() ]
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
That function is unnecessarily called from
dwc3_gadget_reset_interrupt(). Gadget drivers (and
thus, functions) are required to dequeue all pending
requests when they get notified about a USB Bus
Reset.
Trying to make sure there are no pending requests
only serves the purpose of working around possibly
bad gadgets.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This helper will be responsible for reading and
parsing our properties. No functional changes in
this patch, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This little helper will be used to setup anything
related to GCTL register. There are no functional
changes, this is a cleanup only patch.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This little helper will be used to make sure we're
dealing with a valid Synopsys DWC3 or DWC3.1 core.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For the usb31 IP and from version 2.90a of the usb3 IP, the core
supports HW exit from L1 in HS. Enable it, otherwise the controller may
never exit from LPM to do a transfer.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Member @mem in struct dwc3 is not used in any places. Clean up it.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We should never kill the machine just because some
USB endpoint type is wrong. WARN about it and move
on.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We don't need to know about short packets unless
gadget driver told us it's not ok to see them on the
bus. In the normal situation we can continue
processing the list of requests if we get a Short
packet.
Also, note that we're making sure ISP is only set
for OUT endpoints, where that setting is valid.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
CSP bit is only valid for OUT endpoints. Synopsys
databook is unclear if HW ignores CSP for IN
endpoints (chances are, it does) but to avoid
problems, let's make sure to set CSP only when valid
to do so.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By extracting smaller functions from
dwc3_ep0_handle_feature(), it becomes far easier to
understand what's going on. Cleanup only, no
functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We want to reduce the usage of dwc3_trace() in favor
of proper tracepoints which can be enabled/disabled
by the user. Let's start with our register
accessors.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We shouldn't have any glue layer which doesn't
compile everywhere. In order to make sure this is
always the case, make sure COMPILE_TEST is properly
added at dependency list of a config entry.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We don't need dwc3_trace() unless we're building a
kernel with CONFIG_FTRACE. This patch reduces
dwc3.ko text size a bit while also removing overhead
of dwc3_trace() calls.
text data bss dec hex filename
50796 581 0 51377 c8b1 drivers/usb/dwc3/dwc3.o
43961 581 0 44542 adfe drivers/usb/dwc3/dwc3.o.patched
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We can offset the latency of a full Start Transfer
command - where we _must_ poll for its completion -
to usb_ep_enable() time. This means that once
requests start showing up from the gadget driver, we
can rely on No Response Update Transfer command -
where we don't need to poll for completion.
This patch, starts implementing this method for Bulk
endpoints, even though, technically, we could extend
it to all other endpoints in future commits.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case of periodic transfers, let's pretty print
the size field as a multiplier followed by length,
such as :
3x 1024
instead of:
33555456
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Cc: Li Yang <leoli@freescale.com>
Cc: <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Cc: Ashwini Pahuja <ashwini.linux@gmail.com>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove this macro
from the driver.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <linux-usb@vger.kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb_endpoint_maxp() is now returning maxpacket
correctly - iow only bits 10:0. We can finaly remove
XHCI's private GET_MAX_PACKET macro.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Cc: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Cc: Li Yang <leoli@freescale.com>
Cc: <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Cc: Ashwini Pahuja <ashwini.linux@gmail.com>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <linux-usb@vger.kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Acked-by: Peter Chen <Peter.Chen@nxp.com>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to Dave Miller "the networking stack has a
hard requirement that all SKBs which are transmitted
must have their completion signalled in a fininte
amount of time. This is because, until the SKB is
freed by the driver, it holds onto socket,
netfilter, and other subsystem resources."
In summary, this means that using TX IRQ throttling
for the networking gadgets is, at least, complex and
we should avoid it for the time being.
Cc: <stable@vger.kernel.org>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With this extra piece of information, it will be
easier to find mismatches between driver and HW.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We will be using dwc3_ep0_state_string() from within
our tracepoints, so we need to move that helper to
debug.h in order for it to be accessible.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Removing some trace prints which were made redundant
when we started decoding events and TRBs completely
within their respective trace points.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC3 can tell us which phase of a setup transfer
we're getting into. Let's decode it from the event
to make it easier to debug.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link State Change events are only needed for
debugging and to apply certain workarounds on known
errata. Let's save a few cycles by disabling these
events completely on working revisions of the core.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There might be situations where a Start Transfer
command might fail, if that ever happens, instead of
simply removing the request from our list, we should
give the request back to the gadget driver,
otherwise we might eventually starve it from requests.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
No Response Update Transfer is a special type of
Update Transfer command which can be used whenever
we're not relying on XferNotReady to prepare
transfers. With this, we don't need to wait for
CMDACT to be cleared and issue further commands to
the endpoint straight away.
Let's start using this version to skip the long-ish
wait.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The cmd argument we pass to
dwc3_send_gadget_ep_cmd() could contain extra
arguments embedded. When checking for StartTransfer
command, we need to make sure to match only lower 4
bits which contain the actual command and ignore the
rest.
Reported-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case of High-Speed, High-Bandwidth endpoints, we
need to tell DWC3 that we have more than one packet
per interval. We do that by setting PCM1 field of
Isochronous-First TRB.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
ep->mult is supposed to be set to Isochronous and
Interrupt Endapoint's multiplier value. This value
is computed from different places depending on the
link speed.
If we're dealing with HighSpeed, then it's part of
bits [12:11] of wMaxPacketSize. This case wasn't
taken into consideration before.
While at that, also make sure the ep->mult defaults
to one so drivers can use it unconditionally and
assume they'll never multiply ep->maxpacket to zero.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb_endpoint_maxp() returns wMaxPacketSize in its
raw form. Without taking into consideration that it
also contains other bits reserved for isochronous
endpoints.
This patch fixes one occasion where this is a
problem by making sure that we initialize
ep->maxpacket only with lower 10 bits of the value
returned by usb_endpoint_maxp(). Note that seperate
patches will be necessary to audit all call sites of
usb_endpoint_maxp() and make sure that
usb_endpoint_maxp() only returns lower 10 bits of
wMaxPacketSize.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3-st uses pinctrl_pm_select_*_state() however it
doesn't include the necessary header. Fix the build
break caused by that, by simply including the
missing header.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the USB core files were missing explicit license information.
As all files in the kernel tree are implicitly licensed under the
GPLv2-only, be explicit in case someone get confused looking at
individual files by using the SPDX nomenclature.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
support dual-role mode; there are two ways to switch between
host and device modes, one is by idpin, another is by debugfs
which depends on user input.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
supports host only mode and the code is ported from
host/xhci-mtk.c
IPPC register shared between host and device is moved
into common glue layer.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the MediaTek USB3 controller
integrated into MT8173. It currently supports High-Speed
Peripheral Only mode.
Super-Speed Peripheral, Dual-Role Device and Host Only (xHCI)
modes will be added in the next patchs.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make IPPC register optional to support host side of dual-role mode,
due to it is moved into common glue layer for simplification.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the Davinci OHCI host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
[Axel: adapted and rebased, fixed minor comments]
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch warning for usbip files
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Jai Krishna <rjk1024@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Grub finds incorrect of_node path for devices behind usb hub.
Added devspec sysfs entry for devices behind usb hub so that
right of_node path is returned during grub sysfs walk for these
devices.
Signed-off-by: Vijay Kumar <vijay.ac.kumar@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code is mirrorred in scrolldelta implementations of both vgacon
and sisusb. Let's move the code to a separate helper where we will
perform a common cleanup and further changes.
While we are moving the code, make it linear and save one indentation
level. This is done by returning from the "!lines" then-branch
immediatelly. This allows flushing the else-branch 1 level to the
left, obviously.
Few more new lines and comments were added too.
And do not forget to export the helper function given sisusb can be
built as module.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: <linux-fbdev@vger.kernel.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Scrolling helpers scrup and scrdown both accept 'top' and 'bottom' as
unsigned int. Number of lines 'nr' is accepted as int, but all callers
pass down unsigned too. So change the type of 'nr' to unsigned too.
Now, promote unsigned int from the helpers up to the con_scroll
hook which actually accepted all those as signed int.
Next, the 'dir' parameter can have only two values and we define
constants for that: SM_UP and SM_DOWN. Switch them to enum and do
proper type checking on 'dir' too.
Finally, document the behaviour of the hook.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: <linux-fbdev@vger.kernel.org>
Cc: <linux-usb@vger.kernel.org>
Cc: <linux-parisc@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit b09b5224fe ("usb: chipidea: implement platform shutdown
callback") and commit 43a404577a ("usb: chipidea: host: set host to
be null after hcd is freed") a NULL pointer dereference is caused
on i.MX23 during shutdown. So ensure that role is set to CI_ROLE_END and
we finish interrupt handling before the hcd is deallocated. This avoids
the NULL pointer dereference.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: b09b5224fe ("usb: chipidea: implement platform shutdown callback")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Will probably be helpful if there are any more compatibility issues.
Signed-off-by: Aidan Thornton <makosoft@gmail.com>
Reviewed-by: Grigori Goronzy <greg@chown.ath.cx>
Signed-off-by: Johan Hovold <johan@kernel.org>
With the new reinitialization method, configuring parity, different
frame lengths and different stop bit settings should work as expected
on both CH340G and CH341A. Tested on a loopback-connected CH340G
with a logic analyzer in a number of different configurations.
Based on a patch by Grigori Goronzy
Signed-off-by: Aidan Thornton <makosoft@gmail.com>
Reviewed-by: Grigori Goronzy <greg@chown.ath.cx>
Signed-off-by: Johan Hovold <johan@kernel.org>
Changing the LCR register after initialization does not seem to be reliable
on all chips (particularly not on CH341A). Restructure initialization and
configuration to always reinit the chip on configuration changes instead and
pass the LCR register value directly to the initialization command.
(Note that baud rates above 500kbaud are incorrect, but they're incorrect in
the same way both before and after this patch at least on the CH340G. Fixing
this isn't a priority as higher baud rates don't seem that reliable anyway.)
Cleaned-up version of a patch by Grigori Goronzy
Signed-off-by: Aidan Thornton <makosoft@gmail.com>
Reviewed-by: Grigori Goronzy <greg@chown.ath.cx>
Signed-off-by: Johan Hovold <johan@kernel.org>
No functional changes, this just gives names to some registers and USB
requests based on Grigori Goronzy's work and WinChipTech's Linux driver
(which reassuringly agree), then uses them in place of magic numbers.
This also renames the misnamed BREAK2 register (actually UART config)
Signed-off-by: Aidan Thornton <makosoft@gmail.com>
Reviewed-by: Grigori Goronzy <greg@chown.ath.cx>
Signed-off-by: Johan Hovold <johan@kernel.org>
Including mach/* is frowned upon in device drivers, so get rid of it.
This replaces usb20_clk and code that pokes CFGCHIP2 with a proper phy
driver.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hwrng core used to mask 'quality' with 1023; that has been removed
in commit 506bf0c046 ("hwrng: core - allow
perfect entropy from hardware devices"), so we can now just set quality
to 1024.
Signed-off-by: Julien Cristau <jcristau@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the descriptor-based interface to manipulate GPIOs, instead of
the legacy integer-based interface.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This merges the vendor NEC case with the INTEL and AMD one,
as those 3 do exactly the same thing: disabling of the IO
watchdog.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This removes 10 timer wakeups per second. I'm running this patch for
a while now and haven't spotted any adverse effects.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the more common logging mechanism.
Miscellanea:
o Realign multiline statements
o Coalesce format
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add information regarding lifespan of kref protection:
Clarify comment on kref_get for interrupt in urb in usbtmc_probe()
Add comment on kref_get in usbtmc_open()
Fix endpoint reference in documentation for send_request_dev_dep_msg_in()
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the controller on R-Car Gen3 doesn't have any status registers
to detect initialization (LPSTS.SUSPM = 1) and the initialization needs
up to 45 usec, this patch adds wait after the initialization. Otherwise,
writing other registers (e.g. INTENB0) will fail.
Fixes: de18757e27 ("usb: renesas_usbhs: add R-Car Gen3 power control")
Cc: <stable@vger.kernel.org> # v4.6+
Cc: <balbi@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Increase ohci watchout delay to 275 ms. Previous delay was 250 ms
with 20 ms of slack, after removing slack time some ohci controllers don't
respond in time. Logs from systems with controllers that have the
issue would show "HcDoneHead not written back; disabled"
Signed-off-by: Bryan Paluch <bryanpaluch@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we're booting pandaboard using NFSroot over built-in g_ether, we
can get the following after booting once and doing a warm reset:
g_ether gadget: ecm_open
g_ether gadget: notify connect true
...
WARNING: CPU: 0 PID: 1 at drivers/bus/omap_l3_noc.c:147
l3_interrupt_handler+0x220/0x34c
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4CFG (Read):
Data Access in User mode du ring Functional access
...
Fix the issue by calling pm_runtime functions from
musb_gadget_queue.
Note that in the long run we should be able to queue the pending
transfers if pm_runtime is not active, and flush the queue from
pm_runtime_resume.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we configure musb with 2430 glue as a peripheral, and then rmmod
omap2430 module, we'll get the following error:
[ INFO: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected ]
...
rmmod/413 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
(&phy->mutex){+.+.+.}, at: [<c04b9fd0>] phy_power_off+0x1c/0xb8
[ 204.678710]
and this task is already holding:
(&(&musb->lock)->rlock){-.-...}, at: [<bf3a482c>]
musb_gadget_stop+0x24/0xec [musb_hdrc]
which would create a new lock dependency:
(&(&musb->lock)->rlock){-.-...} -> (&phy->mutex){+.+.+.}
...
This is because some glue layers expect musb_platform_enable/disable
to be called with spinlock held, and 2430 glue layer has USB PHY on
the I2C bus using a mutex.
We could fix the glue layers to take the spinlock, but we still have
a problem of musb_plaform_enable/disable being called in an unbalanced
manner. So that would still lead into USB PHY enable/disable related
problems for omap2430 glue layer.
While it makes sense to only enable USB PHY when needed from PM point
of view, in this case we just can't do it yet without breaking things.
So let's just revert phy_enable/disable related changes instead and
reconsider this after we have fixed musb_platform_enable/disable to
be balanced.
Fixes: a83e17d0f7 ("usb: musb: Improve PM runtime and phy handling for 2430 glue layer")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reset value of RWC is 0, set RemoteWakeupConnected bit explicitly
before calling ohci_run, it also fixes the issue that the mass
storage stick connected wasn't suspended when the system suspend.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the GPIO found on the CP2105. Unlike the GPIO
provided by some of the other devices supported by the cp210x driver, the
GPIO on the CP2015 is muxed on pins otherwise used for serial control
lines. The GPIO have been configured in 2 separate banks as the choice to
configure the pins for GPIO is made separately for pins shared with each
of the 2 serial ports this device provides, though the choice is made for
all pins associated with that port in one go. The choice of whether to use
the pins for GPIO or serial is made by adding configuration to a one-time
programable PROM in the chip and can not be changed at runtime. The device
defaults to GPIO.
This device supports either push-pull or open-drain modes, it doesn't
provide an explicit input mode, though the state of the GPIO can be read
when used in open-drain mode. Like with pin use, the mode is configured in
the one-time programable PROM and can't be changed at runtime.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
Return -EIO on short control transfers rather than -EPROTO which is used
for lower-level transfer errors.
Signed-off-by: Johan Hovold <johan@kernel.org>
Here's a fix for a NULL-deref during probe which could be triggered by a
malicious device, and a fix for some missing error handling in cp210x
that also leaked some bits from the stack. Included is also a new device
id for ftdi_sio.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=jD5W
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.9-rc2
Here's a fix for a NULL-deref during probe which could be triggered by a
malicious device, and a fix for some missing error handling in cp210x
that also leaked some bits from the stack. Included is also a new device
id for ftdi_sio.
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure we have at least one port before attempting to register a
console.
Currently, at least one driver binds to a "dummy" interface and requests
zero ports for it. Should such an interface also lack endpoints, we get
a NULL-deref during probe.
Fixes: e5b1e2062e ("USB: serial: make minor allocation dynamic")
Cc: stable <stable@vger.kernel.org> # 3.11
Signed-off-by: Johan Hovold <johan@kernel.org>
firewire-net:
- set min/max_mtu
- remove fwnet_change_mtu
nes:
- set max_mtu
- clean up nes_netdev_change_mtu
xpnet:
- set min/max_mtu
- remove xpnet_dev_change_mtu
hippi:
- set min/max_mtu
- remove hippi_change_mtu
batman-adv:
- set max_mtu
- remove batadv_interface_change_mtu
- initialization is a little async, not 100% certain that max_mtu is set
in the optimal place, don't have hardware to test with
rionet:
- set min/max_mtu
- remove rionet_change_mtu
slip:
- set min/max_mtu
- streamline sl_change_mtu
um/net_kern:
- remove pointless ndo_change_mtu
hsi/clients/ssi_protocol:
- use core MTU range checking
- remove now redundant ssip_pn_set_mtu
ipoib:
- set a default max MTU value
- Note: ipoib's actual max MTU can vary, depending on if the device is in
connected mode or not, so we'll just set the max_mtu value to the max
possible, and let the ndo_change_mtu function continue to validate any new
MTU change requests with checks for CM or not. Note that ipoib has no
min_mtu set, and thus, the network core's mtu > 0 check is the only lower
bounds here.
mptlan:
- use net core MTU range checking
- remove now redundant mpt_lan_change_mtu
fddi:
- min_mtu = 21, max_mtu = 4470
- remove now redundant fddi_change_mtu (including export)
fjes:
- min_mtu = 8192, max_mtu = 65536
- The max_mtu value is actually one over IP_MAX_MTU here, but the idea is to
get past the core net MTU range checks so fjes_change_mtu can validate a
new MTU against what it supports (see fjes_support_mtu in fjes_hw.c)
hsr:
- min_mtu = 0 (calls ether_setup, max_mtu is 1500)
f_phonet:
- min_mtu = 6, max_mtu = 65541
u_ether:
- min_mtu = 14, max_mtu = 15412
phonet/pep-gprs:
- min_mtu = 576, max_mtu = 65530
- remove redundant gprs_set_mtu
CC: netdev@vger.kernel.org
CC: linux-rdma@vger.kernel.org
CC: Stefan Richter <stefanr@s5r6.in-berlin.de>
CC: Faisal Latif <faisal.latif@intel.com>
CC: linux-rdma@vger.kernel.org
CC: Cliff Whickman <cpw@sgi.com>
CC: Robin Holt <robinmholt@gmail.com>
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Marek Lindner <mareklindner@neomailbox.ch>
CC: Simon Wunderlich <sw@simonwunderlich.de>
CC: Antonio Quartulli <a@unstable.cc>
CC: Sathya Prakash <sathya.prakash@broadcom.com>
CC: Chaitra P B <chaitra.basappa@broadcom.com>
CC: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
CC: MPT-FusionLinux.pdl@broadcom.com
CC: Sebastian Reichel <sre@kernel.org>
CC: Felipe Balbi <balbi@kernel.org>
CC: Arvid Brodin <arvid.brodin@alten.se>
CC: Remi Denis-Courmont <courmisch@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
USB2 host inititated resume, and system suspend bus resume
need to use the same USB_RESUME_TIMEOUT as elsewhere.
This resolves a device disconnect issue at system resume seen
on Intel Braswell and Apollolake, but is in no way limited to
those platforms.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a device is unplugged and replugged during Sx system suspend
some Intel xHC hosts will overwrite the CAS (Cold attach status) flag
and no device connection is noticed in resume.
A device in this state can be identified in resume if its link state
is in polling or compliance mode, and the current connect status is 0.
A device in this state needs to be warm reset.
Intel 100/c230 series PCH specification update Doc #332692-006 Errata #8
Observed on Cherryview and Apollolake as they go into compliance mode
if LFPS times out during polling, and re-plugged devices are not
discovered at resume.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHC in Wildcatpoint-LP PCH is similar to LynxPoint-LP and need the
same quirks to prevent machines from spurious restart while
shutting them down.
Reported-by: Hasan Mahmood <hasan.mahm@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current tiocmget implementation would fail to report errors up the
stack and instead leaked a few bits from the stack as a mask of
modem-status flags.
Fixes: 39a66b8d22 ("[PATCH] USB: CP2101 Add support for flow control")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix to return error code -ENOMEM from the kmalloc() error handling
case instead of 0, as done elsewhere in this function.
Fixes: a19b882c07 ("wusb: Stop using the stack for sg crypto scratch space")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First set of fixes for v4.9-rc cycle. Nothing major
this time around. The most important patches are the
3 fixes in dwc3 (dma_free_coheren() size fix,
queued request accounting fix and Isochronous
StartTransfer fix) and the 3 reverts on dwc2.
We're also including the late atmel UDC fix which
didn't make it into v4.8-final.
-----BEGIN PGP SIGNATURE-----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=Kepq
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.9-rc2
First set of fixes for v4.9-rc cycle. Nothing major
this time around. The most important patches are the
3 fixes in dwc3 (dma_free_coheren() size fix,
queued request accounting fix and Isochronous
StartTransfer fix) and the 3 reverts on dwc2.
We're also including the late atmel UDC fix which
didn't make it into v4.8-final.
This reverts commit aa381a7259 ("usb: dwc2: gadget: fix TX FIFO size
and address initialization").
The original commit removed the FIFO size programming per endpoint. The
DPTXFSIZn register is also used for DIEPTXFn and the SIZE field is r/w
in dedicated fifo mode. So it isn't appropriate to simply remove this
initialization as it might break existing behavior.
Also, some cores might not have enough fifo space to handle the
programming method used in the reverted patch, resulting in fifo
initialization failure.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit ba48eab886 ("usb: dwc2: gadget: change variable
name to more meaningful").
This is needed to cleanly revert commit aa381a7259 ("usb: dwc2:
gadget: fix TX FIFO size and address initialization") which may cause
regressions on some platforms.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This adds support to ftdi_sio for the Infineon TriBoard TC2X7
engineering board for first-generation Aurix SoCs with Tricore CPUs.
Mere addition of the device IDs does the job.
Signed-off-by: Stefan Tauner <stefan.tauner@technikum-wien.at>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Pointing an sg list at the stack is verboten and, with
CONFIG_VMAP_STACK=y, will malfunction. Use kmalloc for the wusb
crypto stack space instead.
Untested -- I'm not entirely convinced that this hardware exists in
the wild.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 2abd9d5fa6 ("usb: dwc3: ep0: Add chained TRB support"), the
size of the memory allocated with 'dma_alloc_coherent()' has been modified
but the corresponding calls to 'dma_free_coherent()' have not been updated
accordingly.
This has been spotted with coccinelle, using the following script:
////////////////////
@r@
expression x0, x1, y0, y1, z0, z1, t0, t1, ret;
@@
* ret = dma_alloc_coherent(x0, y0, z0, t0);
...
* dma_free_coherent(x1, y1, ret, t1);
@script:python@
y0 << r.y0;
y1 << r.y1;
@@
if y1.find(y0) == -1:
print "WARNING: sizes look different: '%s' vs '%s'" % (y0, y1)
////////////////////
Fixes: 2abd9d5fa6 ("usb: dwc3: ep0: Add chained TRB support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
ffs_func_eps_disable is called from atomic context so it cannot sleep
thus cannot grab a mutex. Change the handling of epfile->read_buffer
to use non-sleeping synchronisation method.
Reported-by: Chen Yu <chenyu56@huawei.com>
Signed-off-by: Michał Nazarewicz <mina86@mina86.com>
Fixes: 9353afbbfa ("buffer data from ‘oversized’ OUT requests")
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Chen Yu <chenyu56@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
epfile->ep is protected by ffs->eps_lock (not epfile->mutex) so clear it
while holding the spin lock.
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Chen Yu <chenyu56@huawei.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Although a host-only controller should not have any associated delay,
some rockchip SOC platforms will not show the correct host-values of
registers until after a delay.
So add a 50 ms sleep when in host-only mode.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We cannot pre-start isochronous endpoints because we
rely on the micro-frame number passed via
XferNotReady command for proper Isochronous
scheduling.
Fixes: 08a36b5438 ("usb: dwc3: gadget: simplify __dwc3_gadget_ep_queue()")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some requests could be accounted for multiple
times. Let's fix that so each and every requests is
accounted for only once.
Cc: <stable@vger.kernel.org> # v4.8
Fixes: 55a0237f8f ("usb: dwc3: gadget: use allocated/queued reqs for LST bit")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we don't guarantee that we will always get an
interrupt at least when we're queueing our very last
request, we could fall into situation where we queue
every request with 'no_interrupt' set. This will
cause the link to get stuck.
The behavior above has been triggered with g_ether
and dwc3.
Cc: <stable@vger.kernel.org>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pull MIPS updates from Ralf Baechle:
"This is the main MIPS pull request for 4.9:
MIPS core arch code:
- traps: 64bit kernels should read CP0_EBase 64bit
- traps: Convert ebase to KSEG0
- c-r4k: Drop bc_wback_inv() from icache flush
- c-r4k: Split user/kernel flush_icache_range()
- cacheflush: Use __flush_icache_user_range()
- uprobes: Flush icache via kernel address
- KVM: Use __local_flush_icache_user_range()
- c-r4k: Fix flush_icache_range() for EVA
- Fix -mabi=64 build of vdso.lds
- VDSO: Drop duplicated -I*/-E* aflags
- tracing: move insn_has_delay_slot to a shared header
- tracing: disable uprobe/kprobe on compact branch instructions
- ptrace: Fix regs_return_value for kernel context
- Squash lines for simple wrapper functions
- Move identification of VP(E) into proc.c from smp-mt.c
- Add definitions of SYNC barrierstype values
- traps: Ensure full EBase is written
- tlb-r4k: If there are wired entries, don't use TLBINVF
- Sanitise coherentio semantics
- dma-default: Don't check hw_coherentio if device is non-coherent
- Support per-device DMA coherence
- Adjust MIPS64 CAC_BASE to reflect Config.K0
- Support generating Flattened Image Trees (.itb)
- generic: Introduce generic DT-based board support
- generic: Convert SEAD-3 to a generic board
- Enable hardened usercopy
- Don't specify STACKPROTECTOR in defconfigs
Octeon:
- Delete dead code and files across the platform.
- Change to use all memory into use by default.
- Rename upper case variables in setup code to lowercase.
- Delete legacy hack for broken bootloaders.
- Leave maintaining the link state to the actual ethernet/PHY drivers.
- Add DTS for D-Link DSR-500N.
- Fix PCI interrupt routing on D-Link DSR-500N.
Pistachio:
- Remove ANDROID_TIMED_OUTPUT from defconfig
TX39xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
TX49xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
txx9wdt:
- Add missing clock (un)prepare calls for CCF
BMIPS:
- Add PW, GPIO SDHCI and NAND device node names
- Support APPENDED_DTB
- Add missing bcm97435svmb to DT_NONE
- Rename bcm96358nb4ser to bcm6358-neufbox4-sercom
- Add DT examples for BCM63268, BCM3368 and BCM6362
- Add support for BCM3368 and BCM6362
PCI
- Reduce stack frame usage
- Use struct list_head lists
- Support for CONFIG_PCI_DOMAINS_GENERIC
- Make pcibios_set_cache_line_size an initcall
- Inline pcibios_assign_all_busses
- Split pci.c into pci.c & pci-legacy.c
- Introduce CONFIG_PCI_DRIVERS_LEGACY
- Support generic drivers
CPC
- Convert bare 'unsigned' to 'unsigned int'
- Avoid lock when MIPS CM >= 3 is present
GIC:
- Delete unused file smp-gic.c
mt7620:
- Delete unnecessary assignment for the field "owner" from PCI
BCM63xx:
- Let clk_disable() return immediately if clk is NULL
pm-cps:
- Change FSB workaround to CPU blacklist
- Update comments on barrier instructions
- Use MIPS standard lightweight ordering barrier
- Use MIPS standard completion barrier
- Remove selection of sync types
- Add MIPSr6 CPU support
- Support CM3 changes to Coherence Enable Register
SMP:
- Wrap call to mips_cpc_lock_other in mips_cm_lock_other
- Introduce mechanism for freeing and allocating IPIs
cpuidle:
- cpuidle-cps: Enable use with MIPSr6 CPUs.
SEAD3:
- Rewrite to use DT and generic kernel feature.
USB:
- host: ehci-sead3: Remove SEAD-3 EHCI code
FBDEV:
- cobalt_lcdfb: Drop SEAD3 support
dt-bindings:
- Document a binding for simple ASCII LCDs
auxdisplay:
- img-ascii-lcd: driver for simple ASCII LCD displays
irqchip i8259:
- i8259: Add domain before mapping parent irq
- i8259: Allow platforms to override poll function
- i8259: Remove unused i8259A_irq_pending
Malta:
- Rewrite to use DT
of/platform:
- Probe "isa" busses by default
CM:
- Print CM error reports upon bus errors
Module:
- Migrate exception table users off module.h and onto extable.h
- Make various drivers explicitly non-modular:
- Audit and remove any unnecessary uses of module.h
mailmap:
- Canonicalize to Qais' current email address.
Documentation:
- MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
Loongson1C:
- Add CPU support for Loongson1C
- Add board support
- Add defconfig
- Add RTC support for Loongson1C board
All this except one Documentation fix has sat in linux-next and has
survived Imagination's automated build test system"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (127 commits)
Documentation: MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
MIPS: ptrace: Fix regs_return_value for kernel context
MIPS: VDSO: Drop duplicated -I*/-E* aflags
MIPS: Fix -mabi=64 build of vdso.lds
MIPS: Enable hardened usercopy
MIPS: generic: Convert SEAD-3 to a generic board
MIPS: generic: Introduce generic DT-based board support
MIPS: Support generating Flattened Image Trees (.itb)
MIPS: Adjust MIPS64 CAC_BASE to reflect Config.K0
MIPS: Print CM error reports upon bus errors
MIPS: Support per-device DMA coherence
MIPS: dma-default: Don't check hw_coherentio if device is non-coherent
MIPS: Sanitise coherentio semantics
MIPS: PCI: Support generic drivers
MIPS: PCI: Introduce CONFIG_PCI_DRIVERS_LEGACY
MIPS: PCI: Split pci.c into pci.c & pci-legacy.c
MIPS: PCI: Inline pcibios_assign_all_busses
MIPS: PCI: Make pcibios_set_cache_line_size an initcall
MIPS: PCI: Support for CONFIG_PCI_DOMAINS_GENERIC
MIPS: PCI: Use struct list_head lists
...
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johan Hovold