Add two device IDs found in an out-of-tree driver downloadable
from Netgear.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the module sends bursts of data, sometimes a deadlock happens in
the hso driver when the tty buffer doesn't get the chance to be flushed
quickly enough.
Remove the endless while loop in function put_rxbuf_data() which is
called by the urb completion handler.
If there isn't enough room in the tty buffer, discards all the data
received in the URB.
Cc: David Miller <davem@davemloft.net>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jan Dumon <j.dumon@option.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workqueue "retry_unthrottle_workqueue" is not scheduled anywhere
in the code. So, remove it.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The transport offset of the IPv4 packet should be fixed and wouldn't
be out of the hw limitation, so the r8152_csum_workaround() should
be used for IPv6 packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smsc95xx needs to resume with reset operation. Otherwise it causes
system hang by network error like below after resume. This case appears
on odroid u3 board.
[ 9.727600] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.727648] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.727689] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.727728] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.729486] PM: resume of devices complete after 2011.219 msecs
[ 10.117609] Restarting tasks ... done.
[ 11.725099] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 13.480846] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 13.481361] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
...
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum jumbo frame size for RTL8153 is 9K bytes.
Change the max rx packet size to 9K.
Change the use of the shared fifo from 6K (default) to 12K for tx.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device should be waked up from runtime suspend before dumping
the hw counter.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the system is too busy to complete the urb, the tx timout function
would be called. This causes the other tx urbs would be killed, too.
Increase the tx timeout to avoid it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a new version of the Telewell 4G modem working with, but not
recognized by this driver.
Signed-off-by: Bernd Wachter <bernd.wachter@jolla.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Messages from the modem exceeding 256 bytes cause communication
failure.
The WDM protocol is strictly "read on demand", meaning that we only
poll for unread data after receiving a notification from the modem.
Since we have no way to know how much data the modem has to send,
we must make sure that the buffer we provide is "big enough".
Message truncation does not work. Truncated messages are left unread
until the modem has another message to send. Which often won't
happen until the userspace application has given up waiting for the
final part of the last message, and therefore sends another command.
With a proper CDC WDM function there is a descriptor telling us
which buffer size the modem uses. But with this vendor specific
implementation there is no known way to calculate the exact "big
enough" number. It is an unknown property of the modem firmware.
Experience has shown that 256 is too small. The discussion of
this failure ended up concluding that 512 might be too small as
well. So 1024 seems like a reasonable value for now.
Fixes: 41c47d8cfd ("net: huawei_cdc_ncm: Introduce the huawei_cdc_ncm driver")
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-By: Enrico Mioso <mrkiko.rs@gmail.com>
Tested-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/core/rtnetlink.c
net/core/skbuff.c
Both conflicts were very simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Lars writes: "I'm only 99% sure that the net interfaces are qmi
interfaces, nothing to lose by adding them in my opinion."
And I tend to agree based on the similarity with the two Olicard
modems we already have here.
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/net/inetpeer.h
net/ipv6/output_core.c
Changes in net were fixing bugs in code removed in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Each iPad model has a different product id, this patch adds support for iPad 2
(pid 0x12a2) and iPad 3 (pid 0x12a6). Note that iPad 2 must be jailbroken and a
third-party app must be used for tethering to work. On iPad 3, tethering works
out of the box (assuming your ISP is nice).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The min_tx_pkt variable decides the cutoff point where the driver
will stop padding out NTBs to maximum size. The padding is a tradeoff
where we use some USB bus bandwidth to allow the device to receive
fixed size buffers. Different devices will have different optimal
settings, spanning from no padding at all to padding every NTB.
There is no way to automatically figure out which setting is best
for a specific device.
The default value is a reasonable tradeoff, calculated based on the
USB packet size and out NTB max size. This may have to be changed
along with any tx_max changes.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mandatory GetNtbParameters control request is an important part of
the host <-> device protocol negotiation in CDC NCM (and CDC MBIM). It
gives device limits which the host must obey when configuring the
protocol aggregation variables. The driver will enforce this by
rejecting attempts to set any of the tunable variables to a value
which is not supported by the device. Exporting the parameter block
helps userspace decide which values are allowed without resorting
to trial and error.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool coalesce API is not applicable for this driver. Forcing
it to fit the NCM aggregation redefined the API in a driver specific
way, which is much worse than defining a clean new API. These ethtool
coalesce functions have therefore been replaced by a new sysfs API.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attach a driver specific sysfs group to the netdev, and use it
for the rx/tx aggregation variables.
The datagram aggregation defined by the CDC NCM specification is
specific to this device class (including CDC MBIM). Using the
ethtool interrupt coalesce API as an interface to the aggregation
parameters redefined that API in a driver specific and confusing
way. A sysfs group
- makes it clear that this is a driver specific userspace API, and
- allows us to export the real values instead of some translated
version, and
- lets us include more aggregation variables which were impossible
to force into the ethtool API.
Additionally, using sysfs allows tuning the driver on space
constrained hosts where userspace tools like ethtool are undesired.
Suggested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't matter whether the buffer size goes up or down. We have to
keep usbnet and device syncronized to be able to split transfers at the
correct boundaries. The spec allow skipping short packets when using
max sized transfers. If we don't tell usbnet about our new expected rx
buffer size, then it will merge and/or split NTBs. The driver does not
support this, and the result will be lots of framing errors.
Fix by always reallocating usbnet rx buffers when the rx_max value
changes.
Fixes: 68864abf08 ("net: cdc_ncm: support rx_max/tx_max updates when running")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are calling usbnet_start_xmit() to flush any remaining data,
depending on the side effect that tx_curr_skb is set to NULL,
ensuring a new allocation using the updated tx_max. But this
side effect will only happen if there were any cached data ready
to transmit. If not, then an empty tx_curr_skb is still allocated
using the old tx_max size. Free it to avoid a buffer overrun.
Fixes: 68864abf08 ("net: cdc_ncm: support rx_max/tx_max updates when running")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cloning the big skbs we use for USB buffering chokes up TCP and
SCTP because the socket memory limits are hitting earlier than
they should. It is better to unconditionally copy the unwrapped
packets to freshly allocated skbs.
Reported-by: Jim Baxter <jim_baxter@mentor.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interface is unusable, as the cdc-wdm character device doesn't reply to
any QMI command. Also, the out-of-tree Sierra Wireless GobiNet driver fully
skips it.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A set of new VID/PIDs retrieved from the out-of-tree GobiNet/GobiSerial
Sierra Wireless drivers.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a typo here where we test for USB_CDC_NCM_NTH32_SIGN instead
of USB_CDC_NCM_NTB32_SUPPORTED. The test probably still works as
written because 0x686D636E has (1 << 1) set and doesn't have (1 << 0)
set.
Fixes: f8afb73da3 ('net: cdc_ncm: factor out one-time device initialization')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The upper timer_interval limit is arbitrary and much higher
than anything usable in the real world. Reducing it from 15s
to ~4s to make the timer_interval fit in an u32 does not make
much difference. The limit is still outside the practical
bounds.
This eliminates the need for a 64bit timer_interval, fixing a
build error related to 64bit division:
drivers/built-in.o: In function `cdc_ncm_get_coalesce':
ak8975.c:(.text+0x1ac994): undefined reference to `__aeabi_uldivmod'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can end up with a freshly allocated tx_curr_skb with no frames
in it. In this case it does not make any sense to start the timer.
This avoids the timer periodically trying to start tx when there
is nothing in the queue.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling netif_carrier_{on,off} is sufficient. There is no need
to duplicate the carrier state in a driver specific flag.
Acked-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of devices request much larger buffers than reasonable. This
cause real problems for users of hosts with limited resources.
Reducing the default buffer size to 16kB for such devices is
a reasonable trade-off between allowing them to aggregate traffic
and avoiding memory exhaustion on resource restrained hosts.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
To have an idea of the effects of the protocol coalescing
it's useful to have some counters showing the different
aspects.
Due to the asymmetrical usbnet interface the netdev
rx_bytes counter has been counting real received payload,
while the tx_bytes counter has included the NCM/MBIM
framing overhead. This overhead can be many times the
payload because of the aggressive padding strategy of
this driver, and will vary a lot depending on device
and traffic.
With very few exceptions, users are only interested in
the payload size. Having an somewhat accurate payload
byte counter is particularly important for mobile
broadband devices, which many NCM devices and of course
all MBIM devices are. Users and userspace applications
will use this counter to monitor account quotas.
Having protocol specific counters for the overhead, we are
now able to correct the tx_bytes netdev counter so that
it shows the real payload
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We pad frames larger than X to maximum size for devices which
don't need a ZLP after maximum sized frames. This allows the
device to optimize its transfers for one fixed buffer size.
X was arbitrarily set at 512 bytes regardless of real buffer
maximum, causing extreme overheads due to excessive padding of
larger tx buffers. Limit the padding to at most 3 full USB
packets, still allowing the overhead to payload ratio of 3/1.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many newer NCM and MBIM devices will request a maximum tx
datagram count which is much smaller than our hard-coded
absolute max. We can reduce the overhead without sacrificing
any of the simplicity for these devices, by simply using the
true negotiated count in when calculated the maximum NTH and
NDP header sizes.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Datagram coalescing is an integral part of the NCM and MBIM
protocols, intended to reduce the interrupt load primarily
on the device end of the USB link. As with all coalescing
solutions, there is a trade-off between buffering and
interrupts.
The current defaults are based on the assumption that device
side buffers should be the limiting factor. However, many
modern high speed LTE modems suffers from buffer-bloat,
making this assumption fail. This results in sub-optimal
performance due to excessive coalescing. And in cases where
such modems are connected to cheap embedded hosts there is
often severe buffer allocation issues, giving very noticeable
performance degradation .
A start on improving this is going from build time hard
coded limits to per device user configurable limits. The
ethtool coalescing API was selected as user interface
because, although the tuned values are buffer sizes, these
settings directly control datagram coalescing.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finish the rx_max/tx_max setup by flushing buffers and
informing usbnet about the changes. This way, the settings
can be modified while the netdev is up and running.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have split out the part of the device setup
which MUST be done with the data interface in altsetting 0,
we can delay the rest of the initialization. This allows us
to move some of post-init buffer size config from bind to
the appropriate setup function.
The purpose of this refactoring is to collect all code
adjusting the rx_max and tx_max buffers in one place, so
that it is easier to call it from multiple call sites.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the parts of setup dealing with device initialization from
parts just setting defaults for attributes which might be
changed after initialization.
Some commands of the device initialization are only allowed when
the data interface is in its disabled altsetting, so we must
separate them out of we are to allow rerunning parts of setup.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split out the part of setup dealing with updating the rx_max
and tx_max buffer sizes so that this code can be reused for
dynamically updating the limits.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NCM class match in the cdc_mbim driver is confusing and
cause unexpected behaviour. The USB core guarantees that a
USB interface is in altsetting 0 when probing starts. This
means that devices implementing a NCM 1.0 backwards
compatible MBIM function (a "NCM/MBIM function") always hit
the NCM entry in the cdc_mbim driver match table. Such
functions will never match any of the MBIM entries.
This causes unexpeced behaviour for cases where the NCM and
MBIM entries are differet, which is currently the case for
all except Ericsson devices.
Improve the probing of NCM/MBIM functions by looking up the
device again in the cdc_mbim match table after switching to
the MBIM identity.
The shared altsetting selection is updated to better
accommodate the new probing logic, returning the preferred
altsetting for the control interface instead of the data
interface. The control interface altsetting update is moved
to the cdc_mbim driver. It is never necessary to change the
control interface altsetting for NCM.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Reported by: Yu-an Shih <yshih@nvidia.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSS VLANs are pseudo network interfaces representing arbitrary
data streams, and specifically not IP. Preventing spurious IP
packets can sometimes be a hassle. The kernel will for example
send an IPv6 Router Solicit when the interface is brought up
unless the user has been careful enough to disable IPv6 first.
Such packets forwared to a MBIM DSS session will look like
spurious noise to the device, and can cause it to log an error
or even malfunction.
Drop all IP packets on the designated DSS VLANs to prevent such
unwanted spurious transmissions.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Reported-by: Arnaud Desmier <adesmier@sequans.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cdc_mbim driver maps 802.1q VLANs to MBIM IP and DSS
sessions. MBIM IP session 0 is handled as an exception and
is mapped to untagged frames.
This patch adds optional support for remapping MBIM IP
session 0 to 802.1q VLAN ID 4094 instead. The default
behaviour is not changed. The new behaviour is triggered
by adding a link for this previously unsupported VLAN.
The untagged mapping was chosen initially to support the
assumed most common use case: Most current MBIM devices only
support a single IP session (i.e. session 0 only), and using
untagged frames lets the users completely ignore the
additonal complexity of the multiplexing layer.
But when the multiplexing features of MBIM are used, then
this netdev gets a double meaning: It becomes the master
interface for all the VLAN subdevs the additional sessions
are mapped to, while still serving as the untagged IP
interface for session 0.
This can be problematic, especially when using Device Service
Streams (DSS), as have become apparent recently with the
availability of devices with real DSS support. Some use cases
need to e.g set a MTU which is higher than allowed for IP
Session 0. The dual role also leads to the situation where
the IP Session 0 interface cannot be taken down without
breaking unrelated IP or DSS sessions - a devastating side
effect which applications managing a simple IP session cannot
be expected to be aware of. A typical DHCP client will assume
that it should bring the interface down after releasing the
IP lease.
These problems can be avoided by tagging IP session 0 packets
too, making this session similar to all other multiplexed
sessions. This redefines the main netdev as an upper master
interface only.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __vlan_find_dev_deep should always called in RCU, according
David's suggestion, rename to __vlan_find_dev_deep_rcu looks more
reasonable.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver maps 802.1q VLANs to MBIM sessions. The mapping is based on
a bogus assumption that all tagged frames will use the acceleration API
because we enable NETIF_F_HW_VLAN_CTAG_TX. This fails for e.g. frames
tagged in userspace using packet sockets. Such frames will erroneously
be considered as untagged and silently dropped based on not being IP.
Fix by falling back to looking into the ethernet header for a tag if no
accelerated tag was found.
Fixes: a82c7ce5bc ("net: cdc_ncm: map MBIM IPS SessionID to VLAN ID")
Cc: Greg Suarez <gsuarez@smithmicro.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4d619f625a ("net: cdc_ncm: no point in filling up the NTBs
if we send ZLPs") changed the padding logic for devices with the ZLP
flag set. This meant that frames of any size will be sent without
additional padding, except for the single byte added if the size is
a multiple of the USB packet size. But if the unpadded size is
identical to the maximum frame size, and the maximum size is a
multiplum of the USB packet size, then this one-byte padding will
overflow the buffer.
Prevent padding if already at maximum frame size, letting usbnet
transmit a ZLP instead in this case.
Fixes: 4d619f625a ("net: cdc_ncm: no point in filling up the NTBs if we send ZLPs")
Reported by: Yu-an Shih <yshih@nvidia.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan writes:
"The Dell drivers use the same configuration for PIDs:
81A2: Dell Wireless 5806 Gobi(TM) 4G LTE Mobile Broadband Card
81A3: Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card
81A4: Dell Wireless 5570e HSPA+ (42Mbps) Mobile Broadband Card
81A8: Dell Wireless 5808 Gobi(TM) 4G LTE Mobile Broadband Card
81A9: Dell Wireless 5808e Gobi(TM) 4G LTE Mobile Broadband Card
These devices are all clearly Sierra devices, but are also definitely
Gobi-based. The A8 might be the MC7700/7710 and A9 is likely a MC7750.
>From DellGobi5kSetup.exe from the Dell drivers:
usbif0: serial/firmware loader?
usbif2: nmea
usbif3: modem/ppp
usbif8: net/QMI"
Reported-by: AceLan Kao <acelan.kao@canonical.com>
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of older CMOTech modems are based on Qualcomm
chips and exporting a QMI/wwan function.
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device is unplugged, the driver would try to disable the
device. Add checking the flag of RTL8152_UNPLUG to skip setting
the device when it is unplugged. This could shorten the time of
unloading the driver.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device provides QMI and ethernet functionality via a standard CDC
ethernet descriptor. But when driven by cdc_ether, the QMI
functionality is unavailable because only cdc_ether can claim the USB
interface. Thus blacklist the device in cdc_ether and add its IDs to
qmi_wwan, which enables both QMI and ethernet simultaneously.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/marvell/mvneta.c
The mvneta.c conflict is a case of overlapping changes,
a conversion to devm_ioremap_resource() vs. a conversion
to netdev_alloc_pcpu_stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a race which happens by freeing an object on the stack.
Quoting Julius:
> The issue is
> that it calls usbnet_terminate_urbs() before that, which temporarily
> installs a waitqueue in dev->wait in order to be able to wait on the
> tasklet to run and finish up some queues. The waiting itself looks
> okay, but the access to 'dev->wait' is totally unprotected and can
> race arbitrarily. I think in this case usbnet_bh() managed to succeed
> it's dev->wait check just before usbnet_terminate_urbs() sets it back
> to NULL. The latter then finishes and the waitqueue_t structure on its
> stack gets overwritten by other functions halfway through the
> wake_up() call in usbnet_bh().
The fix is to just not allocate the data structure on the stack.
As dev->wait is abused as a flag it also takes a runtime PM change
to fix this bug.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Reported-by: Grant Grundler <grundler@google.com>
Tested-by: Grant Grundler <grundler@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
Documentation/devicetree/bindings/net/micrel-ks8851.txt
net/core/netpoll.c
The net/core/netpoll.c conflict is a bug fix in 'net' happening
to code which is completely removed in 'net-next'.
In micrel-ks8851.txt we simply have overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
According to "Universal Serial Bus Communications Class Subclass
Specification for Mobile Broadband Interface Model, Revision 1.0,
Errata-1" published by USB-IF, the wMTU field of the MBIM extended
functional descriptor indicates the operator preferred MTU for IP data
streams.
This patch modifies cdc_ncm_setup to ensure that the MTU value set on
the usbnet device does not exceed the operator preferred MTU indicated
by wMTU if the MBIM device exposes a MBIM extended functional
descriptor.
Signed-off-by: Ben Chan <benchan@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a context modified revert of commit 6a9612e2cb
("net: cdc_ncm: remove ncm_parm field") which introduced
a NCM specification violation, causing setup errors for
some devices. These errors resulted in the device and
host disagreeing about shared settings, with complete
failure to communicate as the end result.
The NCM specification require that many of the NCM specific
control reuests are sent only while the NCM Data Interface
is in alternate setting 0. Reverting the commit ensures that
we follow this requirement.
Fixes: 6a9612e2cb ("net: cdc_ncm: remove ncm_parm field")
Reported-and-tested-by: Pasi Kärkkäinen <pasik@iki.fi>
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"I know this is a bit more than you want to see, and I've told the
wireless folks under no uncertain terms that they must severely scale
back the extent of the fixes they are submitting this late in the
game.
Anyways:
1) vmxnet3's netpoll doesn't perform the equivalent of an ISR, which
is the correct implementation, like it should. Instead it does
something like a NAPI poll operation. This leads to crashes.
From Neil Horman and Arnd Bergmann.
2) Segmentation of SKBs requires proper socket orphaning of the
fragments, otherwise we might access stale state released by the
release callbacks.
This is a 5 patch fix, but the initial patches are giving
variables and such significantly clearer names such that the
actual fix itself at the end looks trivial.
From Michael S. Tsirkin.
3) TCP control block release can deadlock if invoked from a timer on
an already "owned" socket. Fix from Eric Dumazet.
4) In the bridge multicast code, we must validate that the
destination address of general queries is the link local all-nodes
multicast address. From Linus Lüssing.
5) The x86 BPF JIT support for negative offsets puts the parameter
for the helper function call in the wrong register. Fix from
Alexei Starovoitov.
6) The descriptor type used for RTL_GIGA_MAC_VER_17 chips in the
r8169 driver is incorrect. Fix from Hayes Wang.
7) The xen-netback driver tests skb_shinfo(skb)->gso_type bits to see
if a packet is a GSO frame, but that's not the correct test. It
should use skb_is_gso(skb) instead. Fix from Wei Liu.
8) Negative msg->msg_namelen values should generate an error, from
Matthew Leach.
9) at86rf230 can deadlock because it takes the same lock from it's
ISR and it's hard_start_xmit method, without disabling interrupts
in the latter. Fix from Alexander Aring.
10) The FEC driver's restart doesn't perform operations in the correct
order, so promiscuous settings can get lost. Fix from Stefan
Wahren.
11) Fix SKB leak in SCTP cookie handling, from Daniel Borkmann.
12) Reference count and memory leak fixes in TIPC from Ying Xue and
Erik Hugne.
13) Forced eviction in inet_frag_evictor() must strictly make sure all
frags are deleted, otherwise module unload (f.e. 6lowpan) can
crash. Fix from Florian Westphal.
14) Remove assumptions in AF_UNIX's use of csum_partial() (which it
uses as a hash function), which breaks on PowerPC. From Anton
Blanchard.
The main gist of the issue is that csum_partial() is defined only
as a value that, once folded (f.e. via csum_fold()) produces a
correct 16-bit checksum. It is legitimate, therefore, for
csum_partial() to produce two different 32-bit values over the
same data if their respective alignments are different.
15) Fix endiannes bug in MAC address handling of ibmveth driver, also
from Anton Blanchard.
16) Error checks for ipv6 exthdrs offload registration are reversed,
from Anton Nayshtut.
17) Externally triggered ipv6 addrconf routes should count against the
garbage collection threshold. Fix from Sabrina Dubroca.
18) The PCI shutdown handler added to the bnx2 driver can wedge the
chip if it was not brought up earlier already, which in particular
causes the firmware to shut down the PHY. Fix from Michael Chan.
19) Adjust the sanity WARN_ON_ONCE() in qdisc_list_add() because as
currently coded it can and does trigger in legitimate situations.
From Eric Dumazet.
20) BNA driver fails to build on ARM because of a too large udelay()
call, fix from Ben Hutchings.
21) Fair-Queue qdisc holds locks during GFP_KERNEL allocations, fix
from Eric Dumazet.
22) The vlan passthrough ops added in the previous release causes a
regression in source MAC address setting of outgoing headers in
some circumstances. Fix from Peter Boström"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (70 commits)
ipv6: Avoid unnecessary temporary addresses being generated
eth: fec: Fix lost promiscuous mode after reconnecting cable
bonding: set correct vlan id for alb xmit path
at86rf230: fix lockdep splats
net/mlx4_en: Deregister multicast vxlan steering rules when going down
vmxnet3: fix building without CONFIG_PCI_MSI
MAINTAINERS: add networking selftests to NETWORKING
net: socket: error on a negative msg_namelen
MAINTAINERS: Add tools/net to NETWORKING [GENERAL]
packet: doc: Spelling s/than/that/
net/mlx4_core: Load the IB driver when the device supports IBoE
net/mlx4_en: Handle vxlan steering rules for mac address changes
net/mlx4_core: Fix wrong dump of the vxlan offloads device capability
xen-netback: use skb_is_gso in xenvif_start_xmit
r8169: fix the incorrect tx descriptor version
tools/net/Makefile: Define PACKAGE to fix build problems
x86: bpf_jit: support negative offsets
bridge: multicast: enable snooping on general queries only
bridge: multicast: add sanity check for general query destination
tcp: tcp_release_cb() should release socket ownership
...
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_cow_head() before editing the tx packet header. The header
would be reallocated if it is shared.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are 4 USB fixes for your current tree.
Two of them are reverts to hopefully resolve the nasty XHCI regressions
we have been having on some types of devices. The other two are quirks
for some Logitech video devices.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlMbu0sACgkQMUfUDdst+yl/MgCeJbq5Lre/M59O5YVWhS3fghsG
PisAoI7t2LLnhiC/DwZD10vs2hEkZxw2
=R/Qt
-----END PGP SIGNATURE-----
Merge tag 'usb-3.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are 4 USB fixes for your current tree.
Two of them are reverts to hopefully resolve the nasty XHCI
regressions we have been having on some types of devices. The other
two are quirks for some Logitech video devices"
* tag 'usb-3.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
Revert "USBNET: ax88179_178a: enable tso if usb host supports sg dma"
Revert "xhci 1.0: Limit arbitrarily-aligned scatter gather."
usb: Make DELAY_INIT quirk wait 100ms between Get Configuration requests
usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e
Support hw IPv6 checksum for TCP and UDP packets.
Note that the hw has the limitation of the range of the transport
offset. Besides, the TCP Pseudo Header of the IPv6 TSO of the hw
bases on the Microsoft document which excludes the packet length.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support scatter gather and TSO.
Adjust the tx checksum function and set the max gso size to fix the
size of the tx aggregation buffer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Continue dealing with the remain rx packets, even though the allocation
of the skb fail. This could calculate the correct dropped packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
move the tx_bottom() from delayed_work to tasklet. It makes the rx
and tx balanced. If the device is in runtime suspend when getting
the tx packet, wakeup the device before trasmitting.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check tx agg list before spin lock to avoid doing spin lock every
times.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use spin_lock and spin_unlock in interrupt context.
The ndo_start_xmit would not be called in interrupt context, so
replace the relative spin_lock_irqsave and spin_unlock_irqrestore
with spin_lock_bh and spin_unlock_bh.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3804fad454.
This commit, together with commit 247bf55727
"xhci 1.0: Limit arbitrarily-aligned scatter gather." were
origially added to get xHCI 1.0 hosts and usb ethernet ax88179_178a devices
working together with scatter gather. xHCI 1.0 hosts pose some requirement on how transfer
buffers are aligned, setting this requirement for 1.0 hosts caused USB 3.0 mass
storage devices to fail more frequently.
USB 3.0 mass storage devices used to work before 3.14-rc1. Theoretically,
the TD fragment rules could have caused an occasional disk glitch.
Now the devices *will* fail, instead of theoretically failing.
>From a user perspective, this looks like a regression; the USB device obviously
fails on 3.14-rc1, and may sometimes silently fail on prior kernels.
The proper soluition is to implement the TD fragment rules for xHCI 1.0 hosts,
but for now, revert this patch until scatter gather can be properly supported.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rtl8152_get_stats() returns the point address of the struct
net_device_stats. This could be got from struct net_device directly.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add or remove some empty lines. Replace the spaces with the tabs.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are known issues for switching the drivers between ECM mode and
vendor mode. The interrup transfer may become abnormal. The hardware
may have the opportunity to die if you change the configuration without
unloading the current driver first, because all the control transfers
of the current driver would fail after the command of switching the
configuration.
Although to use the ecm driver and vendor driver independently is fine,
it may have problems to change the driver from one to the other by
switching the configuration. Additionally, now the vendor mode driver
is more powerful than the ECM driver. Thus, disable the ECM mode driver,
and let r8152 to set the configuration to vendor mode and reset the
device automatically.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the USB device ID for the D-Link DUB-1312 USB 3.0 to Gigabit Ethernet
Adapter to the AX88179/178A driver.
Signed-off-by: Gerry Demaret <gerry@tigron.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace netif_rx with netif_receive_skb to avoid disabling irq frequently
for increasing the efficiency.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support runtime suspend for RTL8152 and RTL8153.
Move tx_bottom() from tasklet to delayed_work. That avoids to
transmit tx packets after calling autosuspend.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add up method for rtl_ops and asign relative functions. Move
clear_bp() and hw_phy_cfg() from init method to up method of rtl_ops.
Call rtl_ops.up() for ndo_open() and rtl_ops.down for ndo_stop().
Replace allocating the memory in probe() with in ndo_open().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY reset is necessary after some hw settings. However, it would
cause the linking down, and so does the set_speed function. Combine
the PHY reset with set_speed function. That could reduce the frequency
of linking down and accessing the PHY register.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the method of enabling the PHY to clear BMCR_PDOWN only.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace getting one item from a list with getting the whole list one time.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Except for RTL_VER_01, replace loading the MAC address from PLA_IDR
with from PLA_BACKUP. The default MAC address may be modified by
the other OS, so the PLA_IDR may be not the default MAC address.
The data in the PLA_BACKUP address of the RTL_VER_01 may be destoryed,
so load MAC address from PLA_IDR for RTL_VER_01.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the following functions.
- r8153_u1u2en
- r8153_u2p3en
- r8153_power_cut_en
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace some codes with the following three functions.
- rtl_drop_queued_tx
- rxdy_gated_en
- r8152_power_cut_en
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the following functions which is for the further coding.
- rtl_clear_bp
- r8153_clear_bp
- r8153_teredo_off
- r8152b_disable_aldps
- r8152b_enable_aldps
- r8152b_hw_phy_cfg
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a generic hard_header_len check from the usbnet
module that is causing dropped packages under certain circumstances
for devices that send rx packets that cross urb boundaries.
One example is the AX88772B which occasionally send rx packets that
cross urb boundaries where the remaining partial packet is sent with
no hardware header. When the buffer with a partial packet is of less
number of octets than the value of hard_header_len the buffer is
discarded by the usbnet module.
With AX88772B this can be reproduced by using ping with a packet
size between 1965-1976.
The bug has been reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=29082
This patch introduces the following changes:
- Removes the generic hard_header_len check in the rx_complete
function in the usbnet module.
- Introduces a ETH_HLEN check for skbs that are not cloned from
within a rx_fixup callback.
- For safety a hard_header_len check is added to each rx_fixup
callback function that could be affected by this change.
These extra checks could possibly be removed by someone
who has the hardware to test.
- Removes a call to dev_kfree_skb_any() and instead utilizes the
dev->done list to queue skbs for cleanup.
The changes place full responsibility on the rx_fixup callback
functions that clone skbs to only pass valid skbs to the
usbnet_skb_return function.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct driver_info ax88178_info is assigned the function
asix_rx_fixup_common as it's rx_fixup callback. This means that
FLAG_MULTI_PACKET must be set as this function is cloning the
data and calling usbnet_skb_return. Not setting this flag leads
to usbnet_skb_return beeing called a second time from within
the rx_process function in the usbnet module.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use %zu for size_t in order to avoid the following build
warning in printks.
drivers/net/usb/sr9800.c: In function 'sr9800_bind'
drivers/net/usb/sr9800.c:826:2: warning: format '%ld' expects argument of type 'long int' but argument 5 has type 'size_t'
[-Wformat]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PXS8 and PHS8 devices show up with PID 0x0053 they will expose both a
QMI port and a WWAN interface.
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
CC: David McCullough <david.mccullough@accelecon.com>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver description files give these descriptions to the vendor specific
ports on this modem:
VID_19D2&PID_1270&MI_00: "ZTE MF667 Diagnostics Port"
VID_19D2&PID_1270&MI_01: "ZTE MF667 AT Port"
VID_19D2&PID_1270&MI_02: "ZTE MF667 ATExt2 Port"
VID_19D2&PID_1270&MI_03: "ZTE MF667 ATExt Port"
VID_19D2&PID_1270&MI_04: "ZTE MF667 USB Modem"
VID_19D2&PID_1270&MI_05: "ZTE MF667 Network Adapter"
Signed-off-by: Raymond Wanyoike <raymond.wanyoike@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like this function was intended to have special handling for
urb statuses of -ENOENT and -ECONNRESET. But now it just prints some
debugging and returns at the start of the function.
I have removed the dead code, it's still in the git history if anyone
wants to revive it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The submission of the interrupt transfer should be done after setting
the bit of WORK_ENABLE, otherwise the callback function would have
the opportunity to be returned directly.
Clear the bit of WORK_ENABLE before killing the interrupt transfer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device was mentioned in an OpenWRT forum. Seems to have a "standard"
Sierra Wireless ifnumber to function layout:
0: qcdm
2: nmea
3: modem
8: qmi
9: storage
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
net/ipv4/tcp_metrics.c
Overlapping changes between the "don't create two tcp metrics objects
with the same key" race fix in net and the addition of the destination
address in the lookup key in net-next.
Minor overlapping changes in bnx2x driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the limitation that the ecm and r8152 drivers couldn't coexist.
- Remove the devices from the blacklist of relative drivers.
- Remove usb_driver_set_configuration() from r8152 driver.
- Modify the id_table of the r8152 driver for the vendor mode only.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warnings and error:
- WARNING: usb_free_urb(NULL) is safe this check is probably not required
- WARNING: kfree(NULL) is safe this check is probably not required
- ERROR: do not use C99 // comments
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The r8152 could support RTL8153. Update the relative descriptor.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of new dm96xx variants now exist.
Reported-by: Joseph Chang <joseph_chang@davicom.com.tw>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 60e453a940 ("USBNET: fix handling padding packet")
added an extra SG entry in case padding is necessary, but
failed to update the initialisation of the list. This can
cause list traversal to fall off the end of the list,
resulting in an oops.
Fixes: 60e453a940 ("USBNET: fix handling padding packet")
Reported-by: Thomas Kear <thomas@kear.co.nz>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Replace pr_warn_ratelimited() with net_ratelimit() and netdev_warn().
- Adjust the algnment of some messages.
- Remove the peroid.
- Fix some messages don't have terminating newline.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing serial state notification handling expected older Option
devices, having a hardcoded assumption that the Modem port was always
USB interface #2. That isn't true for devices from the past few years.
hso_serial_state_notification is a local cache of a USB Communications
Interface Class SERIAL_STATE notification from the device, and the
USB CDC specification (section 6.3, table 67 "Class-Specific Notifications")
defines wIndex as the USB interface the event applies to. For hso
devices this will always be the Modem port, as the Modem port is the
only port which is set up to receive them by the driver.
So instead of always expecting USB interface #2, instead validate the
notification with the actual USB interface number of the Modem port.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the boolean value with the error code for the return value
of the rtl_ops_init().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some information of the device may be used in other functions. Move
the relative code to make sure it would be initialzed correctly
before using it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the tabs of the variables declaration with the spaces.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value should be the boolean value, not the error code.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Spotted-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support new chip RTL8153 which is the USB 3.0 giga ethernet adapter.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the contents of rtl8152_enable() into rtl_set_eee_plus() and
rtl_enable().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The different chips may have different settings. This makes it easy
to let different chips have the same flow with differnt settings.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace RX_BUF_THR with RX_THR_HIGH.
Replace RWSUME_INDICATE with RESUME_INDICATE.
Add CRC_SIZE, TX_ALIGN, and RX_ALIGN.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old method to access PHY is through mdio channel. Replace it
with the OCP channel.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the locations of rtl8152_unload() and ocp_reg_write().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even with the quirks in commit dabdaf0c (mcs7830: Fix link state
detection) there are still spurious link-down events for some chips
where the false link-down events count go over a few hundreds.
This patch takes a more conservative approach and only looks at
link-down events where the link-down state is not combined with other
states (e.g. half/full speed, pending frames in SRAM or TX status
information valid). In all other cases we assume the link is up.
Tested on MCS7830CV-DA (USB ID 9710:7830).
Cc: Ondrej Zary <linux@rainbow-software.org>
Cc: Michael Leun <lkml20120218@newton.leun.net>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain dm962x revisions contain an bug, where if a USB bulk transfer retry
(E.G. if bulk crc mismatch) happens right after a transfer with odd or
maxpacket length, the internal tx hardware fifo gets out of sync causing
the interface to stop working.
Work around it by adding up to 3 bytes of padding to ensure this situation
cannot trigger.
This workaround also means we never pass multiple-of-maxpacket size skb's
to usbnet, so the length adjustment to handle usbnet's padding of those can
be removed.
Cc: <stable@vger.kernel.org>
Reported-by: Joseph Chang <joseph_chang@davicom.com.tw>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver nowadays also support dm9620/dm9621a based USB 2.0 ethernet
adapters, so adjust module/driver description and Kconfig help text to
match.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dm9620/dm9621a require room for 4 byte padding even in dm9601 (3 byte
header) mode.
Cc: <stable@vger.kernel.org>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dm9621a is functionally identical to dm9620, so the existing handling can
directly be used.
Thanks to Davicom for sending me a dongle.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Oliver Neukum <oliver@neukum.org>
CC: Steve Glendinning <steve.glendinning@shawell.net>
CC: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data from the hardware should be little endian. Correct the
declaration.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum packet number which a tx aggregation buffer could contain
is the tx_qlen.
tx_qlen = buffer size / (packet size + descriptor size).
If the tx buffer is empty and the queued packets are more than the
maximum value which is defined above, stop the tx queue. Wake the
tx queue if tx queue is stopped and the queued packets are less than
tx_qlen.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the code for sending the packet in the rtl8152_start_xmit().
Let rtl8152_start_xmit() to queue the packet only, and schedule a
tasklet to send the queued packets. This simplify the code and make
sure all the packet would be sent by the original order.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx/rx would access the memory which is out of the desired range.
Modify the method of checking the end of the memory to avoid it.
For r8152_tx_agg_fill(), the variable remain may become negative.
However, the declaration is unsigned, so the while loop wouldn't
break when reaching the end of the desied memory. Although to change
the declaration from unsigned to signed is enough to fix it, I also
modify the checking method for safe. Replace
remain = rx_buf_sz - sizeof(*tx_desc) -
(u32)((void *)tx_data - agg->head);
with
remain = rx_buf_sz - (int)(tx_agg_align(tx_data) - agg->head);
to make sure the variable remain is always positive. Then, the
overflow wouldn't happen.
For rx_bottom(), the rx_desc should not be used to calculate the
packet length before making sure the rx_desc is in the desired range.
Change the checking to two parts. First, check the descriptor is in
the memory. The other, using the descriptor to find out the packet
length and check if the packet is in the memory.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is harmless but cdc_ncm_setup() returns negative error codes
truncated to u8 values. There is only one caller and treats all
non-zero returns as errors but doesn't store the the return code. So
the code works correctly but it's messy and upsets the static checkers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 7b0c5f21f3
"sierra_net: keep status interrupt URB active", sierra_net triggers
status interrupt polling before the net_device is opened (in order to
properly receive the sync message response).
To be able to receive further interrupts, the interrupt urb needs to be
re-submitted, so this patch removes the bogus check for netif_running().
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove device IDs of NCM-like (but not NCM-conformant) devices, that are
handled by the huawwei_cdc_ncm driver now.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver supports devices using the NCM protocol as an encapsulation layer
for other protocols, like the E3131 Huawei 3G modem. This drivers approach was
heavily inspired by the qmi_wwan/cdc_mbim approach & code model.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers implementing NCM-like protocols, may re-use those functions, as is
the case in the huawei_cdc_ncm driver.
Export them via EXPORT_SYMBOL_GPL, in accordance with how other functions have
been exported.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/netconsole.c
net/bridge/br_private.h
Three mostly trivial conflicts.
The net/bridge/br_private.h conflict was a function signature (argument
addition) change overlapping with the extern removals from Joe Perches.
In drivers/net/netconsole.c we had one change adjusting a printk message
whilst another changed "printk(KERN_INFO" into "pr_info(".
Lastly, the emulex change was a new inline function addition overlapping
with Joe Perches's extern removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are MBIM devices out there reporting
dwNtbInMaxSize=2048 dwNtbOutMaxSize=2048
and since the spec require a datagram max size of at least
2048, this means that a full sized datagram will never fit.
Still, sending larger NTBs than the device supports is not
going to help. We do not have any other options than either
a) refusing to bindi, or
b) respect the insanely low value.
Alternative b will at least make these devices work, so go
for it.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it a bit easier for users to figure out what goes
wrong when bind fails.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most setup errors are ignored to ensure maximum firmware
compatibilty. But GET_NTB_PARAMETERS and the functional
descriptors are required. Use proper error codes and
log level if these fail.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rewriting the "set max datagram" part of dc_ncm_setup to
separate the selection and validatation of the size from
the code which optionally informs the device of this
value. This ensures that we use the correct value
regardless of device support for the get and set commands.
Removing some of the many indent levels while doing this
to make the code more readable.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converting the constants used in these comparisons at build
time instead of converting the variables for every received
frame at run time.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
These signatures are well known bit patterns, mostly made up
of ascii characters. Mentally parsing works best if they
are printed in hex.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take advantage of standard device name prefixing and
netdevice msglvl control where possible.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix cut'n'paste typo. Log the bogus length and not the
irrelevant signature.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
usbnet use the hard_mtu value for sizing the tx queue and nothing
else. We will be transmitting buffers of up to tx_max size, so
that's the proper value to give usbnet.
The individual datagram size is completely irrelevant here.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to keep this code duplicated from usbnet.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions were merely wrappers around the usbnet
variants. Remove them.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Padding NTBs to max size is part of the support for devices
optimizing their DMA transfers. This optimization depends on
max sized NTBs not being ZLP terminated. So we are much better
off dropping the padding if we are going to send a ZLP anyway.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The probed interface must be the master/control interface of the
function. Make this explicit and simplify redundant tests.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
header_desc was completely unused and union_desc was never used
outside cdc_ncm_bind_common.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to inform the device about the *new* value, not the
old one.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving the call to cdc_ncm_setup() after the endpoint
setup removes the last remaining reference to ncm_parm
outside cdc_ncm_setup.
Collecting all the ncm_parm based calculations in
cdc_ncm_setup improves readability.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
These fields are only used to prevent printing the same speeds
multiple times if we receive multiple identical speed notifications.
The value of these printk's is questionable, and even more so when
we filter out some of the notifications sent us by the firmware. If
we are going to print any of these, then we should print them all.
Removing little used fields is a bonus.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already use the usbnet udev field everywhere this could have
been used.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Too many pointers back and forth are likely to confuse developers,
creating subtle bugs whenever we forget to syncronize them all.
As a usbnet driver, we should stick with the standard struct
usbnet fields as much as possible. The netdevice is one such
field.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to duplicate stuff already in the common usbnet
struct. We still need to keep our special find_endpoints
function because we need explicit control over the selected
altsetting.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is always a duplicate of the "control" field. It causes
confusion wrt intf_data updates and cleanups.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can avoid the costly division for the common case where
we pad the frame to tx_max size as long as we ensure that
tx_max is either the device specified dwNtbOutMaxSize or not
a multiplum of wMaxPacketSize.
Using the preconverted 'maxpacket' field avoids converting
wMaxPacketSize to CPU endianness for every transmitted frame
And since we only will hit the one byte padding rule for short
frames, we can drop testing the skb for tailroom.
The change means that tx_max now represents the real maximum
skb size, enabling us to allocate the correct size instead of
always making room for one extra byte.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of devices in the wild have turned out to require ZLPs.
Even if this is a spec violation, our priority is to make any
device work as good as possible. Devices needing ZLPs will fail
to receive any full sized frame we send. On the other hand,
devices which do not need the ZLP will still work if we send
them.
This gives us no other option than sending ZLPs by default.
This will prevent devices conforming to the spec from making the
optimizations which are possible without ZLPs. Adding known
such devices to a whitelist, to avoid the possible negative
impact of the new spec violating default.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
MBIM is a point-to-point protocol transporting raw IP packets
with no L2 headers. Only IPv4 and IPv6 are supported. ARP in
particular is not, which is quite logical given the lack of
L2 headers.
The driver still emulates an ethernet interface, dropping all
unsupported protocols, and avoiding neigbour resolving by
setting the IFF_NOARP flag.
The MBIM specification does not explicitly forbid IPv6 Neighbor
Discovery, and it seems the other OS support will respond to
Neighbor Solicitations on MBIM links. There are therefore
buggy devices out there, which despite the pointlessness, still
require Neighbor Discovery for IPv6 over MBIM.
This is incompatible with the IFF_NOARP flag which disables
both ARP and ND. We cannot support ARP in any case, so we
have to keep that flag. This patch implements a workaround
for the buggy devices, letting the driver respond directly
to Neighbor Solicitations from the device.
This is not optimal, but will have minimal effect on any sane
device.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Reported-and-tested-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove AX_MEDIUM_ALWAYS_ONE in AX_MEDIUM_STATUS_MODE register.
Setting this bit may cause TX throttling in Half-Duplex mode.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/qmi_wwan.c
include/net/dst.h
Trivial merge conflicts, both were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the definition of AX_RXHDR_CRC_ERR and
AX_RXHDR_DROP_ERR. They are BIT29 and BIT31 in pkt_hdr
seperately.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a QMI device, manufactured by TCT Mobile Phones.
A companion patch blacklisting this device's QMI interface in the option.c
driver has been sent.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Antonella Pellizzari <anto.pellizzari83@gmail.com>
Tested-by: Dan Williams <dcbw@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return -ENOMEM in the padding pkt alloc fail error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.
Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/usb/qmi_wwan.c
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
include/net/netfilter/nf_conntrack_synproxy.h
include/net/secure_seq.h
The conflicts are of two varieties:
1) Conflicts with Joe Perches's 'extern' removal from header file
function declarations. Usually it's an argument signature change
or a function being added/removed. The resolutions are trivial.
2) Some overlapping changes in qmi_wwan.c and be.h, one commit adds
a new value, another changes an existing value. That sort of
thing.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass-all-multicast is controlled by bit 3 in RX control, not bit 2
(pass undersized frames).
Reported-by: Joseph Chang <joseph_chang@davicom.com.tw>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cinterion PLXX LTE devices have a 0x0060 product ID, not 0x12d1.
The blacklisting in the serial/option driver does actually use the correct PID,
as per commit 8ff10bdb14 ('USB: Blacklisted
Cinterion's PLxx WWAN Interface').
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
Signed-off-by: Aleksander Morgado <aleksander@lanedo.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Christian Schmiedl <christian.schmiedl@gemalto.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer firmware use a new pid and a different interface.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 638c5115a7949(USBNET: support DMA SG) introduces DMA SG
if the usb host controller is capable of building packet from
discontinuous buffers, but missed handling padding packet when
building DMA SG.
This patch attachs the pre-allocated padding packet at the
end of the sg list, so padding packet can be sent to device
if drivers require that.
Reported-by: David Laight <David.Laight@aculab.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'usbpn_probe' is referenced only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Rémi Denis-Courmont <remi@remlab.net>
Cc: Rémi Denis-Courmont <remi@remlab.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use USB_DEVICE_AND_INTERFACE_INFO and USB_VENDOR_AND_INTERFACE_INFO
macros to reduce boilerplate.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: <stable@vger.kernel.org> # 3.0+ as far back as it applies cleanly
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding the device list from the Windows driver description files
included with a new Qualcomm MDM9615 based device, "Alcatel-sbell
ASB TL131 TDD LTE", from China Mobile. This device is tested
and verified to work. The others are assumed to work based on
using the same Windows driver.
Many of these devices support multiple QMI/wwan ports, requiring
multiple interface matching entries. All devices are composite,
providing a mix of one or more serial, storage or Android Debug
Brigde functions in addition to the wwan function.
This device list included an update of one previously known device,
which was incorrectly assumed to have a Gobi 2K layout. This is
corrected.
Reported-by: 王康 <scateu@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
Conflicts:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
net/bridge/br_multicast.c
net/ipv6/sit.c
The conflicts were minor:
1) sit.c changes overlap with change to ip_tunnel_xmit() signature.
2) br_multicast.c had an overlap between computing max_delay using
msecs_to_jiffies and turning MLDV2_MRC() into an inline function
with a name using lowercase instead of uppercase letters.
3) stmmac had two overlapping changes, one which conditionally allocated
and hooked up a dma_cfg based upon the presence of the pbl OF property,
and another one handling store-and-forward DMA made. The latter of
which should not go into the new of_find_property() basic block.
Signed-off-by: David S. Miller <davem@davemloft.net>
This module generates a common default address on init,
using eth_random_addr. Set addr_assign_type to let
userspace know the address is random unless it was
overridden by the minidriver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script: (and a little typing)
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the big USB driver pull request for 3.12-rc1
Lots of USB driver fixes and updates. Nothing major, just the normal
xhci, gadget, and other driver changes. Full details in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlJJ8ACgkQMUfUDdst+ymBAwCgg8czTAuwpCCK7H8LHnC2BsMj
dtUAnjDisrbw4qWSXaaA/sfgSZjKW5G4
=Tman
-----END PGP SIGNATURE-----
Merge tag 'usb-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big USB driver pull request for 3.12-rc1
Lots of USB driver fixes and updates. Nothing major, just the normal
xhci, gadget, and other driver changes. Full details in the shortlog"
* tag 'usb-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (352 commits)
usbcore: fix incorrect type in assignment in descriptors_changed()
usbcore: compare and release one bos descriptor in usb_reset_and_verify_device()
ehci: remove debugging statement with ehci statistics in ehci_stop()
ehci: remove duplicate debug_async_open() prototype in ehci-dbg.c
ehci: enable debugging code when CONFIG_DYNAMIC_DEBUG is set
ehci: remove ehci_vdbg() verbose debugging statements
Documentation sysfs-bus-usb: Document which files are used by libusb
Documentation sysfs-bus-usb: Document the speed file used by libusb
Documentation sysfs-bus-usb: Move files with known users to stable
USB: fix build error when CONFIG_PM_SLEEP isn't enabled
usb: r8a66597-hcd: use platform_{get,set}_drvdata()
usb: phy-tegra-usb: use platform_{get,set}_drvdata()
usb: acm gadget: Null termintate strings table
dma: cppi41: off by one in desc_to_chan()
xhci: Fix warning introduced by disabling runtime PM.
dev-core: fix build break when DEBUG is enabled
USB: OHCI: Allow runtime PM without system sleep
usb: ohci-at91: remove unnecessary dev_set_drvdata()
usb: renesas_usbhs: use platform_{get,set}_drvdata()
usb: fotg210-udc: use platform_{get,set}_drvdata()
...
This patch adds another entry (HP hs2434 Mobile Broadband) to the list
of exceptional devices that require a zero length packet in order to
function properly. This list was added in commit 844e88f0. The hs2434
is manufactured by Sierra Wireless, who also produces the MC7710,
which the ZLP exception list was created for in the first place. So
hopefully it is just this one producer's devices that will need this
workaround.
Tested on a DM1-4310NR HP notebook, which does not function without this
change.
Signed-off-by: Rob Gardner <robmatic@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/iwlwifi/pcie/trans.c
include/linux/inetdevice.h
The inetdevice.h conflict involves moving the IPV4_DEVCONF values
into a UAPI header, overlapping additions of some new entries.
The iwlwifi conflict is a context overlap.
Signed-off-by: David S. Miller <davem@davemloft.net>
As Sergei Shtylyov explained in the #mipslinux IRC channel:
[Mon 2013-08-19 12:28:21 PM PDT] <headless> guys, are you sure it's not "DMA off stack" case?
[Mon 2013-08-19 12:28:35 PM PDT] <headless> it's a known stack corruptor on non-coherent arches
[Mon 2013-08-19 12:31:48 PM PDT] <DonkeyHotei> headless: for usb/ehci?
[Mon 2013-08-19 12:34:11 PM PDT] <DonkeyHotei> headless: explain
[Mon 2013-08-19 12:35:38 PM PDT] <headless> usb_control_msg() (or other such func) should not use buffer on stack. DMA from/to stack is prohibited
[Mon 2013-08-19 12:35:58 PM PDT] <headless> and EHCI uses DMA on control xfers (as well as all the others)
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to get an interface specification if we know it's the
wrong one.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split some parts of code into another function to simplify
tx_bottom(). Use while loop to replace the goto loop.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move some declearation of variables in rx_bottom().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use r8152_get_tx_agg for getting tx agg list
- Replace submit rx with goto submit
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the type of contex of tx_agg and rx_agg from void * to
staruc r8152 *.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the interrupt transfer to replace polling link status.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the tx/rx aggregation which could contain one or more packets
for each bulk in/out. This could reduce the loading of the host
controller by sending less bulk transfer.
The rx packets in the bulk in buffer should be 8-byte aligned, and
the tx packets in the bulk out buffer should be 4-byte aligned.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that the definition of ax88172a_info matches the declaration seen
by users and silence sparse warnings about symbols without declarations
in the global namespace by moving the declaration into the shared header
asix.h.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make functions that are only referenced from ops structures static, they
do not need to be in the global namespace and sparse complains about this.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables 'can_dma_sg' flag for ax88179_178a device
if the attached host controller supports building packet from
discontinuous buffers(DMA SG is possible), so TSO can be enabled
and skb fragment buffers can be passed to usb stack via urb->sg
directly.
With the patch, system CPU utilization decreased ~50% and throughput
increased by ~10% when doing iperf client test on one ARM A15 dual
core board.
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Grant Grundler <grundler@google.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Eric Dumazet <edumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces support of DMA SG if the USB host controller
which usbnet device is attached to is capable of building packet from
discontinuous buffers.
The patch supports passing the skb fragment buffers to usb stack directly
via urb->sg.
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Grant Grundler <grundler@google.com>
Cc: Freddy Xin <freddy@asix.com.tw>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ax88179_tx_fixup() has quite complex code trying to push 8 bytes
of control data (len/mss), but fails to do it properly for TCP packets,
incurring an extra copy and point of memory allocation failure.
Lets use the simple and approved way.
dev->needed_headroom being 8, all frames should have 8 bytes of
headroom, so the extra copy should be unlikely anyway.
This patch should improve performance for TCP xmits.
Reported-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix the conversion between cpu and __le32
- replace some pla_ocp and usb_ocp functions with generic_ocp function
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate the required memory before calling usb_control_msg. And
the additional memory copy is necessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace 0 with the result from usbnet_cdc_bind().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't replace the usb_control_msg() with usbnet_{read,write}_cmd()
which couldn't be called inside suspend/resume callback. Keep the
basic functions unlimited. Instead, using usb_autopm_get_interface()
and usb_autopm_put_interface() in r815x_mdio_{read,write}().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some USB buffers use stack which may not be DMA-able.
Use the buffers from kmalloc to replace those one.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default RX_QLEN()/TX_QLEN() didn't consider super speed
USB device, so only max 4 URBs are scheduled at the same time
for tx/rx, then USB3 NIC can't perform very well.
With this patch, both rx and tx thoughput are increased more than
100Mbps when doing iperf test on ax88179_178a USB 3.0 NIC.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch centralizes computing of max rx/tx qlen, because:
- RX_QLEN()/TX_QLEN() is called in hot path
- computing depends on device's usb speed, now we have ls/fs, hs, ss,
so more checks need to be involved
- in fact, max rx/tx qlen should not only depend on device USB
speed, but also depend on ethernet link speed, so we need to
consider that in future.
- if SG support is done, max tx qlen may need change too
Generally, hard_mtu and rx_urb_size are changed in bind(), reset()
and link_reset() callback, and change mtu network operation, this
patches introduces the API of usbnet_update_max_qlen(), and calls
it in above path.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usbnet doesn't support yet SG, so drivers should not advertise SG or TSO
capabilities, as they allow TCP stack to build large TSO packets that
need to be linearized and might use order-5 pages.
This adds an extra copy overhead and possible allocation failures.
Current code ignore skb_linearize() return code so crashes are even
possible.
Best is to not pretend SG/TSO is supported, and add this again when/if
usbnet really supports SG for devices who could get a performance gain.
Based on a prior patch from Freddy Xin <freddy@asix.com.tw>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>> drivers/net/usb/r815x.c:38:16: sparse: cast to restricted __le32
>> drivers/net/usb/r815x.c:67:15: sparse: cast to restricted __le32
>> drivers/net/usb/r815x.c:69:13: sparse: incorrect type in assignment (different base types)
drivers/net/usb/r815x.c:69:13: expected unsigned int [unsigned] [addressable] [assigned] [usertype] tmp
drivers/net/usb/r815x.c:69:13: got restricted __le32 [usertype] <noident>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Spotted-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
config: make ARCH=avr32 allyesconfig
drivers/net/usb/r8152.c: In function 'rtl8152_start_xmit':
drivers/net/usb/r8152.c:956: warning: integer overflow in expression
955 memset(tx_desc, 0, sizeof(*tx_desc));
> 956 tx_desc->opts1 = cpu_to_le32((len & TX_LEN_MASK) | TX_FS | TX_LS);
957 tp->tx_skb = skb;
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Spotted-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Base on cdc_ether, add the mii functions for RTL8152 and RTL8153.
The RTL8152 and RTL8153 support ECM mode which use the driver of
cdc_ether. Add the mii functions. Then, the basic PHY access is
possible.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
drivers/net/ethernet/renesas/sh_eth.c
net/ipv4/gre.c
The GRE conflict is between a bug fix (kfree_skb --> kfree_skb_list)
and the splitting of the gre.c code into seperate files.
The FEC conflict was two sets of changes adding ethtool support code
in an "!CONFIG_M5272" CPP protected block.
Finally the sh_eth.c conflict was between one commit add bits set
in the .eesr_err_check mask whilst another commit removed the
.tx_error_check member and assignments.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Icera based Huawei modems handled by this driver are not
completely CDC ECM compliant, using the same USB interface for both
control and data. The CDC functional descriptors include a Union
naming this interface as both master and slave, so it is supportable
by relaxing the descriptor parsing in case these interfaces are
identical.
This has been tested on a Huawei K3806 and verified to add support
for that device.
Reported-and-tested-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the USB device ID (0x12ab) to the ipheth network-over-USB-tethering
driver for iOS devices. Applied and tested against mainline tag v3.10
(as well as 3.8.x and 3.6.y kernel for Raspbian on Raspberry pi)
Signed-off-by: Aaron Marburg <amarburg@notetofutureself.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another QMI-speaking device by ZTE, re-branded by ONDA!
I'm connected ovr this device's QMI interface right now, so I can say I tested
it! :)
Note: a follow-up patch was posted to the linux-usb mailing list, to prevent
the option driver from binding to the device's QMI interface, making it
unusable.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A standard Gobi 3000 reference design module.
Reported-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MC8305 module got an additional entry added based solely on
information from a Windows driver *.inf file. We now have the
actual descriptor layout from one of these modules, and it
consists of two alternate configurations where cfg #1 is a
normal Gobi 2k layout and cfg #2 is MBIM only, using interface
numbers 5 and 6 for MBIM control and data. The extra Windows
driver entry for interface number 5 was most likely a bug.
Deleting the bogus entry to avoid unnecessary qmi_wwan probe
failures when using the MBIM configuration.
Reported-by: Lana Black <sickmind@lavabit.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
I tested with the AX88179 usb dongle, if without .reset_resume hook,
after S3/S4 resume you have to enable network interface or reload the
dirver module manually otherwise the network interface can not work.
Signed-off-by: David Chang <dchang@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct a typo in description of driver_info, it should be Gigabit
Signed-off-by: David Chang <dchang@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Found in the Windows INF files while investigating the
Novatel/Verizon USB-1000 device. The USB-1000 is verified as
a Gobi1K device and works with QMI after loading appropriate
firmware.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers that select MII also need to select NET_CORE because MII
depends on it. This is a bit ridiculous because NET_CORE is just a
menu option that doesn't enable any code by itself.
There is also no need for it to be a visible option, since its users
all select it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Another QMI speaking Qualcomm based device, which should be
driven by qmi_wwan, while cdc_ether should ignore it.
Like on other Huawei devices, the wwan function can appear
either as a single vendor specific interface or as a CDC ECM
class function using separate control and data interfaces.
The ECM control interface protocol is 0xff, likely in an
attempt to indicate that vendor specific management is
required.
In addition to the near standard CDC class, Huawei also add
vendor specific AT management commands to their firmwares.
This is probably an attempt to support non-Windows systems
using standard class drivers. Unfortunately, this part of
the firmware is often buggy. Linux is much better off using
whatever native vendor specific management protocol the
device offers, and Windows uses, whenever possible. This
means QMI in the case of Qualcomm based devices.
The E1820 has been verified to work fine with QMI.
Matching on interface number is necessary to distiguish the
wwan function from serial functions in the single interface
mode, as both function types will have class/subclass/function
set to ff/ff/ff.
The control interface number does not change in CDC ECM mode,
so the interface number matching rule is sufficient to handle
both modes. The cdc_ether blacklist entry is only relevant in
CDC ECM mode, but using a similar interface number based rule
helps document this as a transfer from one driver to another.
Other Huawei 02/06/ff devices are left with the cdc_ether driver
because we do not know whether they are based on Qualcomm chips.
The Huawei specific AT command management is known to be somewhat
hardware independent, and their usage of these class codes may
also be independent of the modem hardware.
Reported-by: Graham Inggs <graham.inggs@uct.ac.za>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of dereferencing pointer and put values on stack we could use nice
%*phC specifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge net into net-next because some upcoming net-next changes
build on top of bug fixes that went into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"It's been a while since my last pull request so quite a few fixes have
piled up."
Indeed.
1) Fix nf_{log,queue} compilation with PROC_FS disabled, from Pablo
Neira Ayuso.
2) Fix data corruption on some tg3 chips with TSO enabled, from Michael
Chan.
3) Fix double insertion of VLAN tags in be2net driver, from Sarveshwar
Bandi.
4) Don't have TCP's MD5 support pass > PAGE_SIZE page offsets in
scatter-gather entries into the crypto layer, the crypto layer can't
handle that. From Eric Dumazet.
5) Fix lockdep splat in 802.1Q MRP code, also from Eric Dumazet.
6) Fix OOPS in netfilter log module when called from conntrack, from
Hans Schillstrom.
7) FEC driver needs to use netif_tx_{lock,unlock}_bh() rather than the
non-BH disabling variants. From Fabio Estevam.
8) TCP GSO can generate out-of-order packets, fix from Eric Dumazet.
9) vxlan driver doesn't update 'used' field of fdb entries when it
should, from Sridhar Samudrala.
10) ipv6 should use kzalloc() to allocate inet6 socket cork options,
otherwise we can OOPS in ip6_cork_release(). From Eric Dumazet.
11) Fix races in bonding set mode, from Nikolay Aleksandrov.
12) Fix checksum generation regression added by "r8169: fix 8168evl
frame padding.", from Francois Romieu.
13) ip_gre can look at stale SKB data pointer, fix from Eric Dumazet.
14) Fix checksum handling when GSO is enabled in bnx2x driver with
certain chips, from Yuval Mintz.
15) Fix double free in batman-adv, from Martin Hundebøll.
16) Fix device startup synchronization with firmware in tg3 driver, from
Nithin Sujit.
17) perf networking dropmonitor doesn't work at all due to mixed up
trace parameter ordering, from Ben Hutchings.
18) Fix proportional rate reduction handling in tcp_ack(), from Nandita
Dukkipati.
19) IPSEC layer doesn't return an error when a valid state is detected,
causing an OOPS. Fix from Timo Teräs.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (85 commits)
be2net: bug fix on returning an invalid nic descriptor
tcp: xps: fix reordering issues
net: Revert unused variable changes.
xfrm: properly handle invalid states as an error
virtio_net: enable napi for all possible queues during open
tcp: bug fix in proportional rate reduction.
net: ethernet: sun: drop unused variable
net: ethernet: korina: drop unused variable
net: ethernet: apple: drop unused variable
qmi_wwan: Added support for Cinterion's PLxx WWAN Interface
perf: net_dropmonitor: Remove progress indicator
perf: net_dropmonitor: Use bisection in symbol lookup
perf: net_dropmonitor: Do not assume ordering of dictionaries
perf: net_dropmonitor: Fix symbol-relative addresses
perf: net_dropmonitor: Fix trace parameter order
net: fec: use a more proper compatible string for MVF type device
qlcnic: Fix updating netdev->features
qlcnic: remove netdev->trans_start updates within the driver
qlcnic: Return proper error codes from probe failure paths
tg3: Update version to 3.132
...
Added support for Cinterion's PLxx WWAN Interface by adding QMI_FIXED_INTF with
Cinterion's Vendor ID as well as Product ID and WWAN Interface Number.
Signed-off-by: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
Signed-off-by: Christian Schmiedl <christian.schmiedl@gemalto.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a potential race with concurrently running asynchronous
write requests. The values for device's RX control register are now
stored in dynamically allocated buffers so each URB submission has it's
own copy. Doing it the old way is data clobbering prone.
This patch is against latest 'net' tree.
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_usb_driver() eliminates boilerplate and simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
version.h header inclusion is not necessary as detected by
checkversion.pl.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 84ebc10294 (USB: remove
CONFIG_USB_SUSPEND option) failed to remove all of the usages of
USB_SUSPEND throughout the kernel. This patch (as1677) removes the
remaining instances of that symbol.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver and firmware sync up through SYNC messages, and the
firmware's affirmative reply to these SYNC messages appears to be the
"Reset" indication received via the status interrupt endpoint. Thus the
driver needs the status interrupt endpoint always active so that the
Reset indication can be received even if the netdev is closed, which is
the case right after device insertion.
If the Reset indication is not received by the driver, it continues
sending SYNC messages to the firmware, which crashes about 10 seconds
later and the device stops responding.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers (sierra_net) need the status interrupt URB
active even when the device is closed, because they receive
custom indications from firmware. Add functions to refcount
the status interrupt URB submit/kill operation so that
sub-drivers and the generic driver don't fight over whether
the status interrupt URB is active or not.
A sub-driver can call usbnet_status_start() at any time, but
the URB is only submitted the first time the function is
called. Likewise, when the sub-driver is done with the URB,
it calls usbnet_status_stop() but the URB is only killed when
all users have stopped it. The URB is still killed and
re-submitted for suspend/resume, as before, with the same
refcount it had at suspend.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A rebranded Novatel E371 for AT&T's LTE bands. qmi_wwan should drive this
device, while cdc_ether should ignore it. Even though the USB descriptors
are plain CDC-ETHER that USB interface is a QMI interface.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new driver for supporting Realtek RTL8152 Based USB 2.0 Ethernet Adapters
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is bug in the receive path of the asix driver at the time a
packet is received larger than MTU size and DF bit set:
BUG: unable to handle kernel paging request at 0000004000000001
IP: [<ffffffff8126f65b>] skb_release_head_state+0x2d/0xd2
...
Call Trace:
<IRQ>
[<ffffffff8126f86d>] ? skb_release_all+0x9/0x1e
[<ffffffff8126f8ad>] ? __kfree_skb+0x9/0x6f
[<ffffffffa00b4200>] ? asix_rx_fixup_internal+0xff/0x1ae [asix]
[<ffffffffa00fb3dc>] ? usbnet_bh+0x4f/0x226 [usbnet]
...
It is easily reproducable by setting an MTU of 512 e. g. and sending
something like
ping -s 1472 -c 1 -M do $SELF
from another box.
And this is because the rx->ax_skb is freed on error, but rx->ax_skb
is not reset, and the size is not reset to zero in this case.
And since the skb is added again to the usbnet->done skb queue it is
accessing already freed memory, resulting in the BUG when freeing a
2nd time. I therefore think the value 0x0000004000000001 show in the
trace is more or less random data.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're only passing the two high bytes of an integer. It works for
little endian but not for big endian.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights (1721 non-merge commits, this has to be a record of some
sort):
1) Add 'random' mode to team driver, from Jiri Pirko and Eric
Dumazet.
2) Make it so that any driver that supports configuration of multiple
MAC addresses can provide the forwarding database add and del
calls by providing a default implementation and hooking that up if
the driver doesn't have an explicit set of handlers. From Vlad
Yasevich.
3) Support GSO segmentation over tunnels and other encapsulating
devices such as VXLAN, from Pravin B Shelar.
4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.
5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
Dukkipati.
6) In the PHY layer, allow supporting wake-on-lan in situations where
the PHY registers have to be written for it to be configured.
Use it to support wake-on-lan in mv643xx_eth.
From Michael Stapelberg.
7) Significantly improve firewire IPV6 support, from YOSHIFUJI
Hideaki.
8) Allow multiple packets to be sent in a single transmission using
network coding in batman-adv, from Martin Hundebøll.
9) Add support for T5 cxgb4 chips, from Santosh Rastapur.
10) Generalize the VXLAN forwarding tables so that there is more
flexibility in configurating various aspects of the endpoints.
From David Stevens.
11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
from Dmitry Kravkov.
12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
Neira Ayuso.
13) Start adding networking selftests.
14) In situations of overload on the same AF_PACKET fanout socket, or
per-cpu packet receive queue, minimize drop by distributing the
load to other cpus/fanouts. From Willem de Bruijn and Eric
Dumazet.
15) Add support for new payload offset BPF instruction, from Daniel
Borkmann.
16) Convert several drivers over to mdoule_platform_driver(), from
Sachin Kamat.
17) Provide a minimal BPF JIT image disassembler userspace tool, from
Daniel Borkmann.
18) Rewrite F-RTO implementation in TCP to match the final
specification of it in RFC4138 and RFC5682. From Yuchung Cheng.
19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
you like netlink, so I implemented netlink dumping of netlink
sockets.") From Andrey Vagin.
20) Remove ugly passing of rtnetlink attributes into rtnl_doit
functions, from Thomas Graf.
21) Allow userspace to be able to see if a configuration change occurs
in the middle of an address or device list dump, from Nicolas
Dichtel.
22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
Frederic Sowa.
23) Increase accuracy of packet length used by packet scheduler, from
Jason Wang.
24) Beginning set of changes to make ipv4/ipv6 fragment handling more
scalable and less susceptible to overload and locking contention,
from Jesper Dangaard Brouer.
25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
instead. From Hong Zhiguo.
26) Optimize route usage in IPVS by avoiding reference counting where
possible, from Julian Anastasov.
27) Convert IPVS schedulers to RCU, also from Julian Anastasov.
28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
Eitzenberger.
29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
nfnetlink_log, and nfnetlink_queue. From Gao feng.
30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.
31) Support several new r8169 chips, from Hayes Wang.
32) Support tokenized interface identifiers in ipv6, from Daniel
Borkmann.
33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.
34) Add 802.1ad vlan offload support, from Patrick McHardy.
35) Support mmap() based netlink communication, also from Patrick
McHardy.
36) Support HW timestamping in mlx4 driver, from Amir Vadai.
37) Rationalize AF_PACKET packet timestamping when transmitting, from
Willem de Bruijn and Daniel Borkmann.
38) Bring parity to what's provided by /proc/net/packet socket dumping
and the info provided by netlink socket dumping of AF_PACKET
sockets. From Nicolas Dichtel.
39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
Poirier"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
filter: fix va_list build error
af_unix: fix a fatal race with bit fields
bnx2x: Prevent memory leak when cnic is absent
bnx2x: correct reading of speed capabilities
net: sctp: attribute printl with __printf for gcc fmt checks
netlink: kconfig: move mmap i/o into netlink kconfig
netpoll: convert mutex into a semaphore
netlink: Fix skb ref counting.
net_sched: act_ipt forward compat with xtables
mlx4_en: fix a build error on 32bit arches
Revert "bnx2x: allow nvram test to run when device is down"
bridge: avoid OOPS if root port not found
drivers: net: cpsw: fix kernel warn on cpsw irq enable
sh_eth: use random MAC address if no valid one supplied
3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
tg3: fix to append hardware time stamping flags
unix/stream: fix peeking with an offset larger than data in queue
unix/dgram: fix peeking with an offset larger than data in queue
unix/dgram: peek beyond 0-sized skbs
openvswitch: Remove unneeded ovs_netdev_get_ifindex()
...
Here's the big USB pull request for 3.10-rc1.
Lots of USB patches here, the majority being USB gadget changes and
USB-serial driver cleanups, the rest being ARM build fixes / cleanups,
and individual driver updates. We also finally got some chipidea fixes,
which have been delayed for a number of kernel releases, as the
maintainer has now reappeared.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlF+md4ACgkQMUfUDdst+ymkSgCfZWIiCtiX/li0yJqSiRB4yYJx
Ex0AoNemOOf6ywvSOHPbILTbJ1G+c/PX
=JmvB
-----END PGP SIGNATURE-----
Merge tag 'usb-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big USB pull request for 3.10-rc1.
Lots of USB patches here, the majority being USB gadget changes and
USB-serial driver cleanups, the rest being ARM build fixes / cleanups,
and individual driver updates. We also finally got some chipidea
fixes, which have been delayed for a number of kernel releases, as the
maintainer has now reappeared.
All of these have been in linux-next for a while"
* tag 'usb-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (568 commits)
USB: ehci-msm: USB_MSM_OTG needs USB_PHY
USB: OHCI: avoid conflicting platform drivers
USB: OMAP: ISP1301 needs USB_PHY
USB: lpc32xx: ISP1301 needs USB_PHY
USB: ftdi_sio: enable two UART ports on ST Microconnect Lite
usb: phy: tegra: don't call into tegra-ehci directly
usb: phy: phy core cannot yet be a module
USB: Fix initconst in ehci driver
usb-storage: CY7C68300A chips do not support Cypress ATACB
USB: serial: option: Added support Olivetti Olicard 145
USB: ftdi_sio: correct ST Micro Connect Lite PIDs
ARM: mxs_defconfig: add CONFIG_USB_PHY
ARM: imx_v6_v7_defconfig: add CONFIG_USB_PHY
usb: phy: remove exported function from __init section
usb: gadget: zero: put function instances on unbind
usb: gadget: f_sourcesink.c: correct a copy-paste misnomer
usb: gadget: cdc2: fix error return code in cdc_do_config()
usb: gadget: multi: fix error return code in rndis_do_config()
usb: gadget: f_obex: fix error return code in obex_bind()
USB: storage: convert to use module_usb_driver()
...
Here's the big tty/serial driver merge request for 3.10-rc1
Once again, Jiri has a number of TTY driver fixes and cleanups, and
Peter Hurley came through with a bunch of ldisc fixes that resolve a
number of reported issues. There are some other serial driver cleanups
as well.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlF+nSMACgkQMUfUDdst+ymy9QCfRmYn0MC0W+Q1D3Spz87gVsuo
cqEAniu1BEkYZpjAz7ZlIN07Ao0jbQOR
=Osu/
-----END PGP SIGNATURE-----
Merge tag 'tty-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver update from Greg Kroah-Hartman:
"Here's the big tty/serial driver merge request for 3.10-rc1
Once again, Jiri has a number of TTY driver fixes and cleanups, and
Peter Hurley came through with a bunch of ldisc fixes that resolve a
number of reported issues. There are some other serial driver
cleanups as well.
All of these have been in the linux-next tree for a while"
* tag 'tty-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (117 commits)
tty/serial/sirf: fix MODULE_DEVICE_TABLE
serial: mxs: drop superfluous {get|put}_device
serial: mxs: fix buffer overflow
ARM: PL011: add support for extended FIFO-size of PL011-r1p5
serial_core.c: add put_device() after device_find_child()
tty: Fix unsafe bit ops in tty_throttle_safe/unthrottle_safe
serial: sccnxp: Replace pdata.init/exit with regulator API
serial: sccnxp: Do not override device name
TTY: pty, fix compilation warning
TTY: rocket, fix compilation warning
TTY: ircomm: fix DTR being raised on hang up
TTY: synclinkmp: fix DTR being raised on hang up
TTY: synclink_gt: fix DTR being raised on hang up
TTY: synclink: fix DTR being raised on hang up
serial: 8250_dw: Fix the stub for dw8250_probe_acpi()
serial: 8250_dw: Convert to devm_ioremap()
serial: 8250_dw: Set port capabilities based on CPR register
serial: 8250_dw: Let ACPI code extract the DMA client info
serial: 8250_dw: Support clk framework also with ACPI
serial: 8250_dw: Enable runtime PM
...
Pegasus driver used single callback for sync and async control URBs.
Special flags were employed to distinguish between both, but due to flawed
logic it didn't always work. As a result of this change
[get|set]_registers() are now much simpler. Async write is also leaner
and does not use single, statically allocated memory for usb_ctrlrequest,
which is another potential race when asynchronously submitting URBs.
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Duplicated code in routines reading and writing MII registers is now
packed in __mii_op().
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The socket buffer pool for the receive path is now gone. It's existence
didn't make much difference (performance-wise) and the code is better off
without the spinlocks protecting it.
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
drivers/net/ethernet/intel/igb/igb_main.c
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
include/net/scm.h
net/batman-adv/routing.c
net/ipv4/tcp_input.c
The e{uid,gid} --> {uid,gid} credentials fix conflicted with the
cleanup in net-next to now pass cred structs around.
The be2net driver had a bug fix in 'net' that overlapped with the VLAN
interface changes by Patrick McHardy in net-next.
An IGB conflict existed because in 'net' the build_skb() support was
reverted, and in 'net-next' there was a comment style fix within that
code.
Several batman-adv conflicts were resolved by making sure that all
calls to batadv_is_my_mac() are changed to have a new bat_priv first
argument.
Eric Dumazet's TS ECR fix in TCP in 'net' conflicted with the F-RTO
rewrite in 'net-next', mostly overlapping changes.
Thanks to Stephen Rothwell and Antonio Quartulli for help with several
of these merge resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
We normally trust and use the CDC functional descriptors provided by a
number of devices. But some of these will erroneously list the address
reserved for the device end of the link. Attempting to use this on
both the device and host side will naturally not work.
Work around this bug by ignoring the functional descriptor and assign a
random address instead in this case.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Received packets are sometimes addressed to 00:a0:c6:00:00:00
instead of the address the device firmware should have learned
from the host:
321.224126 77.16.85.204 -> 148.122.171.134 ICMP 98 Echo (ping) request id=0x4025, seq=64/16384, ttl=64
0000 82 c0 82 c9 f1 67 82 c0 82 c9 f1 67 08 00 45 00 .....g.....g..E.
0010 00 54 00 00 40 00 40 01 57 cc 4d 10 55 cc 94 7a .T..@.@.W.M.U..z
0020 ab 86 08 00 62 fc 40 25 00 40 b2 bc 6e 51 00 00 ....b.@%.@..nQ..
0030 00 00 6b bd 09 00 00 00 00 00 10 11 12 13 14 15 ..k.............
0040 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 .......... !"#$%
0050 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 &'()*+,-./012345
0060 36 37 67
321.240607 148.122.171.134 -> 77.16.85.204 ICMP 98 Echo (ping) reply id=0x4025, seq=64/16384, ttl=55
0000 00 a0 c6 00 00 00 02 50 f3 00 00 00 08 00 45 00 .......P......E.
0010 00 54 00 56 00 00 37 01 a0 76 94 7a ab 86 4d 10 .T.V..7..v.z..M.
0020 55 cc 00 00 6a fc 40 25 00 40 b2 bc 6e 51 00 00 U...j.@%.@..nQ..
0030 00 00 6b bd 09 00 00 00 00 00 10 11 12 13 14 15 ..k.............
0040 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 .......... !"#$%
0050 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 &'()*+,-./012345
0060 36 37 67
The bogus address is always the same, and matches the address
suggested by many devices as a default address. It is likely a
hardcoded firmware default.
The circumstances where this bug has been observed indicates that
the trigger is related to timing or some other factor the host
cannot control. Repeating the exact same configuration sequence
that caused it to trigger once, will not necessarily cause it to
trigger the next time. Reproducing the bug is therefore difficult.
This opens up a possibility that the bug is more common than we can
confirm, because affected devices often will work properly again
after a reset. A procedure most users are likely to try out before
reporting a bug.
Unconditionally rewriting the destination address if the first digit
of the received packet is 0, is considered an acceptable compromise
since we already have to inspect this digit. The simplification will
cause unnecessary rewrites if the real address starts with 0, but this
is still better than adding additional tests for this particular case.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of LTE devices from different vendors all suffer from the
same firmware bug: Most of the packets received from the device while
it is attached to a LTE network will not have an ethernet header. The
devices work as expected when attached to 2G or 3G networks, sending
an ethernet header with all packets.
This driver is not aware of which network the modem attached to, and
even if it were there are still some packet types which are always
received with the header intact.
All devices supported by this driver have severely limited
networking capabilities:
- can only transmit IPv4, IPv6 and possibly ARP
- can only support a single host hardware address at any time
- will only do point-to-point communcation with the host
Because of this, we are able to reliably identify any bogus raw IP
packets by simply looking at the 4 IP version bits. All we need to
do is to avoid 4 or 6 in the first digit of the mac address. This
workaround ensures this, and fix up the received packets as necessary.
Given the distribution of the bug, it is believed that the source is
the chipset vendor. The devices which are verified to be affected are:
Huawei E392u-12 (Qualcomm MDM9200)
Pantech UML290 (Qualcomm MDM9600)
Novatel USB551L (Qualcomm MDM9600)
Novatel E362 (Qualcomm MDM9600)
It is believed that the bug depend on firmware revision, which means
that possibly all devices based on the above mentioned chipset may be
affected if we consider all available firmware revisions.
The information about affected devices and versions is likely
incomplete. As the additional overhead for packets not needing this
fixup is very small, it is considered acceptable to apply the
workaround to all devices handled by this driver.
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove warning introduced by commit 418fc57 ("usbnet: cdc-ether: apply
usbnet_link_change"):
CHECK .../drivers/net/usb/cdc_ether.c
.../drivers/net/usb/cdc_ether.c:409:46: warning: incorrect type in argument 2 (different base types)
.../drivers/net/usb/cdc_ether.c:409:46: expected bool [unsigned] [usertype] <noident>
.../drivers/net/usb/cdc_ether.c:409:46: got restricted __le16 [usertype] wValue
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The intention was to test against the constant, not the size of
the constant.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link change is detected via the interrupt pipe, and bulk
pipes are responsible for transfering packets, so it is reasonable
to stop bulk transfer after link is reported as off.
Two adavantages may be obtained with stopping bulk transfer
after link becomes off:
- USB bus bandwidth is saved(USB bus is shared bus except for
USB3.0), for example, lots of 'IN' token packets and 'NYET'
handshake packets is transfered on 2.0 bus.
- probabaly power might be saved for usb host controller since
cancelling bulk transfer may disable the asynchronous schedule of
host controller.
With this patch, when link becomes off, about ~10% performance
boost can be found on bulk transfer of anther usb device which
is attached to same bus with the usbnet device, see below
test on next-20130410:
- read from usb mass storage(Sandisk Extreme USB 3.0) on pandaboard
with below command after unplugging ethernet cable:
dd if=/dev/sda iflag=direct of=/dev/null bs=1M count=800
- without the patch
1, 838860800 bytes (839 MB) copied, 36.2216 s, 23.2 MB/s
2, 838860800 bytes (839 MB) copied, 35.8368 s, 23.4 MB/s
3, 838860800 bytes (839 MB) copied, 35.823 s, 23.4 MB/s
4, 838860800 bytes (839 MB) copied, 35.937 s, 23.3 MB/s
5, 838860800 bytes (839 MB) copied, 35.7365 s, 23.5 MB/s
average: 23.6MB/s
- with the patch
1, 838860800 bytes (839 MB) copied, 32.3817 s, 25.9 MB/s
2, 838860800 bytes (839 MB) copied, 31.7389 s, 26.4 MB/s
3, 838860800 bytes (839 MB) copied, 32.438 s, 25.9 MB/s
4, 838860800 bytes (839 MB) copied, 32.5492 s, 25.8 MB/s
5, 838860800 bytes (839 MB) copied, 31.6178 s, 26.5 MB/s
average: 26.1MB/s
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use usbnet_link_change to handle link change centrally.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use usbnet_link_change to handle link change centrally.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use usbnet_link_change to handle link change centrally.
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use usbnet_link_change to handle link change centrally.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use usbnet_link_change to handle link change centrally.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use usbnet_link_change to handle link change centrally.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the introduced usbnet_link_change to handle link change.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses the introduced usbnet_link_change() to handle
link change.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver doesn't implement link_reset() callback, so it needn't
to send link reset event.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the API of usbnet_link_change, so that
usbnet can handle link change centrally, which may help to
implement killing traffic URBs for saving USB bus bandwidth
and host controller power.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Receiving unhandled notifications is most certainly not an error
and should not be logged as one. Knowing that the device sends
notifications we don't handle is useful for developers, but there
is very little a user can do about this. The message is therefore
just annoying noise to most users with devices sending unhandled
notifications like e.g. USB_CDC_NOTIFY_RESPONSE_AVAILABLE
Cc: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
Two minor conflicts in wireless. Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().
Signed-off-by: David S. Miller <davem@davemloft.net>
return -ENOMEM instead if kzalloc of cdc_ncm_ctx structure is failed.
and also remove the comparision of ctx structure with NULL and make
it as !ctx.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables RX of jumbo frames for LAN7500.
Previously the driver would transmit jumbo frames succesfully but
would drop received jumbo frames (incrementing the interface errors
count).
With this patch applied the device can succesfully receive jumbo
frames up to MTU 9000 (9014 bytes on the wire including ethernet
header).
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If suspend callback fails in system sleep context, usb core will
ignore the failure and let system sleep go ahead further, so
this patch doesn't recover device under this situation.
Also add comments on this case.
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If suspend callback fails in system sleep context, usb core will
ignore the failure and let system sleep go ahead further, so
this patch doesn't recover device under this situation.
Also add comments on the case.
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If suspend callback fails in system sleep context, usb core will
ignore the failure and let system sleep go ahead further, so
this patch comments on the case and requires that both
usbnet_suspend() and subdriver->suspend() MUST return 0 in
system sleep context.
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If suspend callback fails in system sleep context, usb core will
ignore the failure and let system sleep go ahead further, so
this patch comments on the case and requires that both
usbnet_suspend() and subdriver->suspend() MUST return 0 in
system sleep context.
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It allows for cleaning up on a considerable amount of places. They did
port_get, hangup, kref_put. Now the only thing needed is to call
tty_port_tty_hangup which does exactly that. And they can also decide
whether to consider CLOCAL or completely ignore that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It allows for cleaning up on a considerable amount of places. They did
port_get, wakeup, kref_put. Now the only thing needed is to call
tty_port_tty_wakeup which does exactly that.
One exception is ifx6x60 where tty_wakeup was open-coded. We now call
tty_wakeup properly there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd329e1 ("net: cdc_ncm: do not bind to NCM compatible MBIM devices")
introduced a new policy, preferring MBIM for dual NCM/MBIM functions if
the cdc_mbim driver was enabled. This caused a regression for users
wanting to use NCM.
Devices implementing NCM backwards compatibility according to section
3.2 of the MBIM v1.0 specification allow either NCM or MBIM on a single
USB function, using different altsettings. The cdc_ncm and cdc_mbim
drivers will both probe such functions, and must agree on a common
policy for selecting either MBIM or NCM. Until now, this policy has
been set at build time based on CONFIG_USB_NET_CDC_MBIM.
Use a module parameter to set the system policy at runtime, allowing the
user to prefer NCM on systems with the cdc_mbim driver.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@stericsson.com>
Reported-by: Geir Haatveit <nospam@haatveit.nu>
Reported-by: Tommi Kyntola <kynde@ts.ray.fi>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=54791
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Kconfig file help information incorrectly mentions that the
SMSC LAN75xx config option is for SMSC LAN95xx devices.
Signed-off-by: Robert de Vries <rhdv@xs4all.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit bd877e4 ("net: qmi_wwan: use a single bind function for
all device types") made Gobi 1K devices fail probing.
Using the number of endpoints in the default altsetting to decide
whether the function use one or two interfaces is wrong. Other
altsettings may provide more endpoints.
With Gobi 1K devices, USB interface #3's altsetting is 0 by default, but
altsetting 0 only provides one interrupt endpoint and is not sufficent
for QMI. Altsetting 1 provides all 3 endpoints required for qmi_wwan
and works with QMI. Gobi 1K layout for intf#3 is:
Interface Descriptor: 255/255/255
bInterfaceNumber 3
bAlternateSetting 0
Endpoint Descriptor: Interrupt IN
Interface Descriptor: 255/255/255
bInterfaceNumber 3
bAlternateSetting 1
Endpoint Descriptor: Interrupt IN
Endpoint Descriptor: Bulk IN
Endpoint Descriptor: Bulk OUT
Prior to commit bd877e4, we would call usbnet_get_endpoints
before giving up finding enough endpoints. Removing the early
endpoint number test and the strict functional descriptor
requirement allow qmi_wwan_bind to continue until
usbnet_get_endpoints has made the final attempt to collect
endpoints. This restores the behaviour from before commit
bd877e4 without losing the added benefit of using a single bind
function.
The driver has always required a CDC Union functional descriptor
for two-interface functions. Using the existence of this
descriptor to detect two-interface functions is the logically
correct method.
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Tested-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a resubmission.
Added kfree() in ax88179_get_eeprom to prevent memory leakage.
Modified "__le16 rxctl" to "u16 rxctl" in "struct ax88179_data" and removed pointless casts.
Removed asix_init and asix_exit functions and added "module_usb_driver(ax88179_178a_driver)".
Fixed endianness issue on big endian systems and verified this driver on iBook G4.
Removed steps that change net->features in ax88179_set_features function.
Added "const" to ethtool_ops structure and fixed the coding style of AX88179_BULKIN_SIZE array.
Fixed the issue that the default MTU is not 1500.
Added ax88179_change_mtu function and enabled the hardware jumbo frame function to support an
MTU higher than 1500.
Fixed indentation and empty line coding style errors.
The _nopm version usb functions were added to access register in suspend and resume functions.
Serveral variables allocted dynamically were removed and replaced by stack variables.
ax88179_get_eeprom were modified from asix_get_eeprom in asix_common.
This patch adds a driver for ASIX's AX88179 family of USB 3.0/2.0
to gigabit ethernet adapters. It's based on the AX88xxx driver but
the usb commands used to access registers for AX88179 are completely different.
This driver had been verified on x86 system with AX88179/AX88178A and
Sitcomm LN-032 USB dongles.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork