The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda61871 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.
The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:
1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.
2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).
The following simplified method is used instead:
All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.
This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.
Fixes: aebda61871 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It just ocurred to me that dwc3 already gives a
really hint of when a setup packet is pending and
that's the SETUP_PENDING TRB Status for EP0 IRQs.
Fix setup_packet_pending initialization based on
that. While at that, also make sure the comment in
gadget.c matches what code is doing.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The last few dev_dbg() messages are converted to
tracepoints and we can finally ignore dev_dbg()
messages during debug sessions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use chained TRB mechanism to handle non maxpacket aligned transfers
greater than bounce buffer size. With this the first TRB will be programmed
to receive 'ALIGN(ur->length - maxp, maxp)' data and the second TRB
will be programmed to receive the remaining data using bounce buffer.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add chained TRB support to ep0. Now TRB's can be chained just by
invoking _dwc3_ep0_start_trans_ with 'chain' parameter set to true.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No functional change. Added a new parameter in _dwc3_ep0_start_trans_ to
indicate whether the TRB is a chained TRB or last TRB. This is in
preparation for adding chained TRB support for ep0.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No functional change. This is in preparation for handling non maxpacket
aligned transfers greater than bounce buffer size. This is basically to
avoid code duplication when using chained TRB transfers to handle
non maxpacket aligned transfers greater than bounce buffer size.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No functional change. Used _roundup_ macro to calculate the transfer
size aligned to maxpacket in dwc3_ep0_complete_data. It also makes it
similar to how transfer size is calculated in __dwc3_ep0_do_control_data.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 uses bounce buffer to handle non max packet aligned OUT transfers and
the size of bounce buffer is 512 bytes. However if the host initiates OUT
transfers of size more than 512 bytes (and non max packet aligned), the
driver throws a WARN dump but still programs the TRB to receive more than
512 bytes. This will cause bounce buffer to overflow and corrupt the
adjacent memory locations which can be fatal.
Fix it by programming the TRB to receive a maximum of DWC3_EP0_BOUNCE_SIZE
(512) bytes.
Cc: <stable@vger.kernel.org> # 3.4+
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This fixes an issue introduced in commit b23c843992 (usb: dwc3:
gadget: fix DEPSTARTCFG for non-EP0 EPs) that made sure we would
only use DEPSTARTCFG once per SetConfig.
The trick is that we should use one DEPSTARTCFG per SetConfig *OR*
SetInterface. SetInterface was completely missed from the original
patch.
This problem became aparent after commit 76e838c9f7 (usb: dwc3:
gadget: return error if command sent to DEPCMD register fails)
added checking of the return status of device endpoint commands.
'Set Endpoint Transfer Resource' command was caught failing
occasionally. This is because the Transfer Resource
Index was not getting reset during a SET_INTERFACE request.
Finally, to fix the issue, was we have to do is make sure that
our start_config_issued flag gets reset whenever we receive a
SetInterface request.
To verify the problem (and its fix), all we have to do is run
test 9 from testusb with 'testusb -t 9 -s 2048 -a -c 5000'.
Tested-by: Huang Rui <ray.huang@amd.com>
Tested-by: Subbaraya Sundeep Bhatta <subbaraya.sundeep.bhatta@xilinx.com>
Fixes: b23c843992 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs)
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 6856d30 (usb: dwc3: ep0: return early
on NULL requests) tried to fix a minor corner
case where we could dereference a NULL pointer
but it also ended up introducing some dead code.
Unfortunately, that dead code, if reached, could
end up starving the endpoint request list because
a request would never be given back when it should.
Fix this by moving the check for empty request list
before its first use.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the following checkpatch warning.
WARNING: break is not useful after a goto or return
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to Section 8.5.3.2 of the USB 2.0 specification,
a USB device must terminate a Data Phase with either a
short packet or a ZLP (if the previous transfer was
a multiple of wMaxPacketSize).
For reference, here's what the USB 2.0 specification, section
8.5.3.2 says:
"
8.5.3.2 Variable-length Data Stage
A control pipe may have a variable-length data phase
in which the host requests more data than is contained
in the specified data structure. When all of the data
structure is returned to the host, the function should
indicate that the Data stage is ended by returning a
packet that is shorter than the MaxPacketSize for the
pipe. If the data structure is an exact multiple of
wMaxPacketSize for the pipe, the function will return
a zero-length packet to indicate the end of the Data
stage.
"
Signed-off-by: Felipe Balbi <balbi@ti.com>
if our list of requests is empty, return early.
There's really nothing to be done in case our
request list is empty anyway because the only
situation where we our list is empty, is when
we're transferring ZLPs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to our Gadget Framework API documentation,
->set_halt() *must* return -EAGAIN if we have pending
transfers (on either direction) or FIFO isn't empty (on
TX endpoints).
Fix this bug so that the mass storage gadget can be used
without stall=0 parameter.
This patch should be backported to all kernels since v3.2.
Cc: <stable@vger.kernel.org> # v3.2+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_gadget_ep0_set_halt() will be called without
locks held in some cases, so we must hold the lock
on our own. While at that, also add a version without
locks to be called in certain conditions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we're debugging hard-to-reproduce and time-sensitive
use cases, printk() poses too much overhead. That's when
the kernel's tracing infrastructure comes into play.
This patch implements a few initial tracepoints for the
dwc3 driver. More traces can be added as necessary in order
to ease the task of debugging dwc3.
Reviewed-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Those functions are only using within debugging
messages, grouping them into debug.h makes sense.
While at that, also add missing multiple inclusion
guard.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dwc3 UDC driver doesn't implement endpoint wedging correctly.
When an endpoint is wedged, the gadget driver should be allowed to
clear the wedge by calling usb_ep_clear_halt(). Only the host is
prevented from resetting the endpoint.
This patch fixes the implementation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Pratyush Anand <pratyush.anand@st.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
These aren't necessary after switch and if blocks.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
before changing to configured state, we need
to wait until gadget driver has had a chance
to process the request.
In case of USB_GADGET_DELAYED_STATUS, that means
we need to defer usb_gadget_set_state() until
the upcoming usb_ep_queue().
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case we're switching back to USB_STATE_ADDRESS
from USB_STATE_CONFIGURED (if host sends
a set configuration command for configuration
zero), we should only switch if the request
is successfully processed by the gadget driver.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is a Linux-only driver which makes use
of GPL-only symbols. It makes no sense to
maintain Dual BSD/GPL licensing for this driver.
Considering that the amount of work to use this
driver in any different operating system would likely
be as large as developing the driver from scratch and
considering that we depend on GPL-only symbols, we
will switch over to a GPL v2-only license.
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/dwc3/ep0.c: In function `__dwc3_ep0_do_control_data':
drivers/usb/dwc3/ep0.c:905: error: `typeof' applied to a bit-field
Looks like a gcc-3.4.5/sparc64 bug.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This resolves the merge problems with:
drivers/usb/dwc3/gadget.c
drivers/usb/musb/tusb6010.c
that had been seen in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of ep0 out, if length is not aligned to maxpacket size then we use
dwc->ep_bounce_addr for dma transfer and not request->dma. Since, we have
alreday done memcpy from dwc->ep0_bounce to request->buf, so we do not need to
issue cache sync function. In fact, cache sync function will bring wrong data
in request->buf from request->dma in this scenario.
So, cache sync function must not be executed in case of ep0 bounced.
Cc: <stable@vger.kernel.org> # v3.4 v3.5
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 68d3e66 (usb: dwc3: ep0: fix for possible early
delayed_status) added handling for early delayed status,
but the current code only works because so far delayed
status will always be on the IN direction.
This patch makes the code more robust by making sure that
we can handle all directions properly.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Due to the late Silicon limitation found, we are
now pre-starting DATA phase's TRBs. If, still, we
get XferNotReady(DATA) we will ignore it unless
we're getting it for the wrong direction.
In that case we must keep the error case handling
plus add a ENDTRANSFER command to forcefully end
the Data TRB we started previously, then continue
to SetStall and so on.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We uncovered a limitation of this core WRT to the
Link Layer Compliance Suite's TD7.06.
On that test, host will start a GetDescriptor(DEVICE)
standard request, but it will do so only on the
SETUP phase, meaning there will *NOT* be any DATA or
STATUS phases.
The idea of the test is to verify robustness of the
IP WRT framing errors, so the test will send a
sequence of different SETUP_DPs each with a different
framing error and the Suite expects us to be able to
receive all SETUP_DPs with no timeouts.
This core, has the ability to tell us which phase the
host is expecting before we start it. Whenever we
receive a TP or DP when no transfers are cached on
the internal IP's caches, the IP will generate a
XferNotReady event with status informing us (in case
of physical ep0/ep1) if it's related to DATA or STATUS
phases - SETUP phase is expected to be prestarted.
Because we're always waiting for XferNotReady
events for DATA and STATUS phases, we will never
be able to know that the Host wants to start another
SETUP phase instead, which will render us "not
compliant" with TD7.06.
In order to "fix" the problem we must not rely
on XferNotReady events for the DATA phase and try
to always pre-start DATA transfers on physical
endpoints 0 and 1. If host goes back to SETUP phase
from DATA phase we will receive a XferComplete for
that phase with TRB's status set to SETUP_PENDING,
which is only useful for printing a debugging log as
the core expects us to still go through to the STATUS
phase, initiate a CONTROL_STATUS TRB just so it
completes right away and, only then, we go back to
the pending SETUP phase.
SNPS has decided to modify the programming model of
the core so that on-demand DATA phases will not be
supported anymore. Note that this limitation does not
affect 2-stage transfers, meaning that if TD7.06 would
start a 2-stage transfer instead of a 3-stage transfer,
we would receive a "fake" XferNotReady(STATUS) which
would complete right after being initiated with
SETUP_PENDING status.
Other endpoints are also not affected, so we can still
use on-demand transfers on Bulk/Isoc/Interrupt endpoints.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Databook doesn't say we should stall if we
get XferNotReady(STATUS) while we're expecting
something else.
Instead of stalling and restarting, tests have
proven that ignoring the event is far more
effective.
This problem has been caught while rewriting
ep0 handling in order we pass Link Layer TD7.6.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We can return early from each if () branch
and split the special cases for clarity. While
at that also add a comment to the delayed_status
case.
Signed-off-by: Felipe Balbi <balbi@ti.com>
As per databook, ACCEPT{U1,U2}ENA bits should be set after receiving
SetConfiguration Command.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
set_halt for ep0 is called to stall a deferred control responses by the
gadget. We already have a function to stall default control endpoint.
This patch points set_halt for ep0 to the already available function.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Michel Sanches <michel.sanches@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case we try to start an invalid test mode, we
will call dwc3_ep0_stall_and_restart() but we will
also call dwc3_ep0_out_start() which will start
a second transfer on ep0.
Let's prevent any problems by returning early in
the error case.
Signed-off-by: Felipe Balbi <balbi@ti.com>
That's a much more intuitive name as that function
is only called at the completion of a Status Phase.
It also matches dwc3_ep0_complete_data() for
the completion of Data Phase.
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB is always little endian, but this driver
could run on non little endian cpus. Let's
be carefull with that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
On our Transfer Not Ready handlers, only
dwc3_ep0_do_control_status() had a different
list of parameters.
Align on the parameters in order to keep consistency.
No functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
IS_ALIGNED provides a much faster operation for
checking proper size alignment then a modulo
operation. Let's use it.
Reported-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When DWC3_EP_PENDING_REQUEST flag is set for a Control OUT Data
phase transfer, we would be missing the proper handling for
unaligned OUT requests, thus hanging a transfer.
Since proper handling is already done on dwc3_ep0_do_control_data(),
we simply re-factor that function so it can be re-used from
__dwc3_gadget_ep0_queue().
Reported-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
we're now have DWC3_EP0_BOUNCE_SIZE to tell
us the actual size of the bufer. Let's use that
instead of ep0 wMaxPacketSize.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This pull request contains one workaround for a Silicon
Issue found on all RTL releases prior to 2.20a, which
would cause a metastability state on Run/Stop bit.
We also have some patches implementing a few extra Standard
requests introduced by USB3 spec (Set SEL and Set Isoch Delay),
as well as one patch, which has been pending for a long time,
implementing LPM support.
Last, but not least, we are splitting the host address space
out of the dwc3 core driver otherwise xHCI won't be able to
request_mem_region() its own address space. This patch is
only needed because we are (as we should) re-using the xHCI
driver, which is a completely separate module.
Together with these three big changes, come a few extra preparatory
patches which most move code around, define macros and so on, as
well as a fix for Isochronous transfers which hasn't been triggered
before.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=qgf/
-----END PGP SIGNATURE-----
Merge tag 'dwc3-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: dwc3: patches for v3.5 merge window
This pull request contains one workaround for a Silicon
Issue found on all RTL releases prior to 2.20a, which
would cause a metastability state on Run/Stop bit.
We also have some patches implementing a few extra Standard
requests introduced by USB3 spec (Set SEL and Set Isoch Delay),
as well as one patch, which has been pending for a long time,
implementing LPM support.
Last, but not least, we are splitting the host address space
out of the dwc3 core driver otherwise xHCI won't be able to
request_mem_region() its own address space. This patch is
only needed because we are (as we should) re-using the xHCI
driver, which is a completely separate module.
Together with these three big changes, come a few extra preparatory
patches which most move code around, define macros and so on, as
well as a fix for Isochronous transfers which hasn't been triggered
before.
[ resolved conflicts and build error in drivers/usb/dwc3/gadget.c - gregkh]
This is basically a noop for DWC3. We don't have
to do anything. Basically we test if the request
parameters are correct, cache the Isochronous
Delay and return success.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch implements Set SEL Standard Request
support for dwc3 driver. It needs to issue a command
to the controller passing the timing we received on
the data phase of the Set SEL request.
Signed-off-by: Felipe Balbi <balbi@ti.com>
On device loading the driver enables LPM and the acceptance of U1 and U2
states. The [Set|Clear]Feature requests for "U1/U2" are forwarded
directly to the hardware and allow / forbid the initiation of the low
power links.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Without this default case returning an error,
thus replying with a stall, we would fail
USB30CV TD 9.11 Bad Feature test case.
Cc: stable@vger.kernel.org
Signed-off-by: Gerard Cauvy <g-cauvy1@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
due to a HW limitation we have a bounce buffer for ep0
out transfers which are not aligned with MaxPacketSize.
On such case we were not increment r->actual as we should.
This patch fixes that mistake.
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
To allow ep0 out transfers of upto bounce buffer size
instead of maxpacketsize, use the transfer size as multiple
of ep0 maxpacket size.
Cc: stable@vger.kernel.org
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here are the changes for v3.4 merge window.
It includes a new glue layer for Samsung's Exynos platform, a simplification of
memory management on DWC3 driver by using dev_xxx functions, a few
optimizations to IRQ handling by dropping memcpy() and using bitshifts, a fix
for TI's OMAP5430 TX Fifo Allocation, two fixes on USB2 test mode
implementation (one on debugfs and one on ep0), and several minor changes such
as whitespace cleanups, simplification of a few parts of the code, decreasing a
long delay to something a bit saner, dropping a header which was included twice
and so on.
The highlight on this merge is the support for Samsung's Exynos platform,
increasing the number of different users for this driver to three.
Note that Samsung Exynos glue layer will only compile on platforms which
provide implementation for the clk API for now. Once Samsung supports
pm_runtime, that limitation can be dropped from the Makefile.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4Z2+
-----END PGP SIGNATURE-----
Merge tag 'dwc3-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: dwc3: changes for v3.4 merge window
Here are the changes for v3.4 merge window.
It includes a new glue layer for Samsung's Exynos platform, a simplification of
memory management on DWC3 driver by using dev_xxx functions, a few
optimizations to IRQ handling by dropping memcpy() and using bitshifts, a fix
for TI's OMAP5430 TX Fifo Allocation, two fixes on USB2 test mode
implementation (one on debugfs and one on ep0), and several minor changes such
as whitespace cleanups, simplification of a few parts of the code, decreasing a
long delay to something a bit saner, dropping a header which was included twice
and so on.
The highlight on this merge is the support for Samsung's Exynos platform,
increasing the number of different users for this driver to three.
Note that Samsung Exynos glue layer will only compile on platforms which
provide implementation for the clk API for now. Once Samsung supports
pm_runtime, that limitation can be dropped from the Makefile.
Conflicts:
drivers/usb/dwc3/gadget.c
Transfer resource index is cleared in hardware when XFERCOMPLETE
event is generated, so clear the driver's res_trans_idx variable
immediately after that event is received. The upcoming hibernation
patches depend on this change.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For am5536udc we have just simple coding style fixes. Nothing that has any
potential to cause any issues going forward.
With mv_udc, there's only one single change removing an unneeded NULL check.
at91_udc also only saw a single change this merge window, and that's only
removing a duplicated header.
The Renesas controller has a few more involved changes. Support for SUDMAC was
added, there's now a special handling of IRQ resources for when the IRQ line is
shared between Renesas controller and SUDMAC, we also had a bug fix where
Renesas controller would sleep in atomic context while doing DMA transfers from
a tasklet. There were also a set of minor cleanups.
The FSL UDC also had a scheduling in atomic context bug fix, but that's all.
Thanks to Sebastian, the dummy_hcd now works better than ever with support for
scatterlists and streams. Sebastian also added SuperSpeed descriptors to the
serial gadgets.
The highlight on this merge is the addition of a generic API for mapping and
unmapping usb_requests. This will avoid code duplication on all UDC controllers
and also kills all the defines for DMA_ADDR_INVALID which UDC controllers
sprinkled around. A few of the UDC controllers were already converted to use
this new API.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RR+f
-----END PGP SIGNATURE-----
Merge tag 'gadget-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB: Gadget: changes for 3.4
This merge is rather big. Here's what it contains:
For am5536udc we have just simple coding style fixes. Nothing that has any
potential to cause any issues going forward.
With mv_udc, there's only one single change removing an unneeded NULL check.
at91_udc also only saw a single change this merge window, and that's only
removing a duplicated header.
The Renesas controller has a few more involved changes. Support for SUDMAC was
added, there's now a special handling of IRQ resources for when the IRQ line is
shared between Renesas controller and SUDMAC, we also had a bug fix where
Renesas controller would sleep in atomic context while doing DMA transfers from
a tasklet. There were also a set of minor cleanups.
The FSL UDC also had a scheduling in atomic context bug fix, but that's all.
Thanks to Sebastian, the dummy_hcd now works better than ever with support for
scatterlists and streams. Sebastian also added SuperSpeed descriptors to the
serial gadgets.
The highlight on this merge is the addition of a generic API for mapping and
unmapping usb_requests. This will avoid code duplication on all UDC controllers
and also kills all the defines for DMA_ADDR_INVALID which UDC controllers
sprinkled around. A few of the UDC controllers were already converted to use
this new API.
Conflicts:
drivers/usb/dwc3/gadget.c
those routines have everything we need to map/unmap
USB requests and it's better to use them.
In order to achieve that, we had to add a simple
change on how we allocate and use our setup buffer;
we cannot allocate it from coherent anymore otherwise
the generic map/unmap routines won't be able to easily
know that the GetStatus request already has a DMA
address.
Signed-off-by: Felipe Balbi <balbi@ti.com>
this will get rid of a useless memcpy on
IRQ handling, thus improving driver performance.
Tested with OMAP5430 running g_mass_storage on
SuperSpeed and HighSpeed.
Note that we are removing the little endian access
of the TRB and all accesses will be in System endianness,
if there happens to be a system in BE, bit 12 of GSBUSCFG0
should be set so that HW does byte invariant BE accesses
when fetching TRBs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
When host requests us to enter a test mode,
we cannot directly enter the test mode before
Status Phase is completed, otherwise the core
will never be able to deliver the Status ZLP
to host, because it has already entered the
requested Test Mode.
In order to fix the error, we move the actual
start of Test Mode right after we receive
Transfer Complete event of the status phase.
Signed-off-by: Gerard Cauvy <g-cauvy1@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to dynamically re-size TxFifos for the
cases where default values will not do.
While at that, we create a simple function which,
for now, will just allocate one full packet fifo
space for each of the enabled endpoints.
This can be improved later in order to allow for
better throughput by allocating more space for
endpoints which could make good use of that like
isochronous and bulk.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Mass Storage gadget will take some time to handle
the SetConfiguration request, but even on those
cases we should move to CONFIGURED state.
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are some situations were we might need to
enable USB Test Modes without having access to a
Host stack. In such situations we cannot rely
solely on USB Control Messages to enable test
features.
For those cases, we will also allow test mode
to be enabled via debugfs and this patch is a
preparation for that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 34c60a7 (usb: dwc3: ep0: tidy up Pending
Request handling) introduced a compile warning
by leaving an unused variable.
This patch fixes that warning:
drivers/usb/dwc3/ep0.c: In function ‘__dwc3_gadget_ep0_queue’:
drivers/usb/dwc3/ep0.c:129:8: warning: unused variable ‘type’
[-Wunused-variable]
Signed-off-by: Felipe Balbi <balbi@ti.com>
The way our code was written, we should never have
a DWC3_EP_PENDING_REQUEST flag set out of a Data Phase
and the code in __dwc3_gadget_ep0_queue() did not
reflect that situation properly.
Tidy up that case to avoid any possible mistakes
when starting requests for IRQs which are long
gone.
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a very small possibility (previously unimagined
by us) that the whole Mass Storage delayed status happens
rather early, before we even get our XferNotReady event.
In that case, we will be queueing a request to ep0 while
we're still on Setup Phase and we would be waiting for
another usb_ep_queue() forever.
Handle such cases by clearing dwc->delayed_status so that
we start control status from the next XferNotReady like
there was no wait for Delayed Status.
Tested against Linux 3.2-rc3 and USB30CV tool from USB-IF
(on a Windows XP with USB3 PCIe card).
Signed-off-by: Felipe Balbi <balbi@ti.com>
previous commit fixed part of it but it was still
calling usb_ep_queue() from IRQ context without
loosing locks. That cannot be done otherwise we will
have a recursive locking.
Also, we need to assign the 'dep' pointer on
dwc->ep0_usb_req otherwise we will have a NULL
pointer dereference on dwc3_map_buffer_to_dma().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of special functions and shortcuts for sending our internal
answers to the host we started doing what the gadget does and used the
public API for this. Since we only were using a few fields the
usb_request was enough. Later added the list handling in order to
synchronize the host / gadget events and now we require to have the
dwc3_request struct around our usb_request or else we touch memory that
does not belong to us. So this patch does this.
Reported-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 revisions <1.88a have an issue which would
case a missing Disconnect event if cable is
disconnected while there's a Setup packet
pending the FIFO.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the re-worked ep0 handling (which uses HW's hints to recognize the ep0
status) we lost the delayed status handling. This is used by the file and mass
storage gadget to gain some extra time so setup its internal status before it
can proceed further requests.
In particular the storage gadget does nothing on USB_REQ_SET_CONFIGURATION but
wakes up a thread which handles the request. If the udc driver continues ep0
handling before the thread did its work then then endpoint is not yet
configured and further requests will fail. Once the gadget is ready, it will
enqueue an empty packet which is used for synchronization.
In order to fix this issue, the patch does the following:
Set ->delayed_status once the delayed_status has been notices and do not
continue on the next XferNotReady event. We will continues ep0 processing once
the gadget enqueued the zero packet for synchronization.
A cleaner approach would be to enforce the gadget to enqueue an empty
(zero) request even for the status phase but this would do for now.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We wait for the XferNotReady before we start the transfer and by then we
know ep0 state in which we supposed to be.
This is some cleanup work for the following patch in which we require to
know the ep0 state before the transfer completes.
While here, also change the argument to dwc3_ep0_do_control_status() so
we don't require the complete event structure but only the required
piece of information.
Inspired-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
sparse caught three mistakes on this driver,
fix them:
drivers/usb/dwc3/ep0.c:806:29: warning: duplicate const
drivers/usb/dwc3/debugfs.c:481:15: warning: symbol 'dwc3_debugfs_init' \
was not declared. Should it be static?
drivers/usb/dwc3/debugfs.c:518:16: warning: symbol 'dwc3_debugfs_exit' \
was not declared. Should it be static?
Signed-off-by: Felipe Balbi <balbi@ti.com>
There were a few coding style issues with this driver
which are now fixed:
drivers/usb/dwc3/debugfs.c:48: WARNING: Use #include \
<linux/uaccess.h> instead of <asm/uaccess.h>
drivers/usb/dwc3/debugfs.c:484: ERROR: space required \
before the open brace '{'
drivers/usb/dwc3/ep0.c:261: WARNING: line over 80 characters
drivers/usb/dwc3/ep0.c:287: WARNING: suspect code indent \
for conditional statements (16, 23)
drivers/usb/dwc3/gadget.c:749: WARNING: line over 80 characters
drivers/usb/dwc3/gadget.c:1267: WARNING: line over 80 characters
drivers/usb/dwc3/gadget.h:116: WARNING: line over 80 characters
drivers/usb/dwc3/io.h:42: WARNING: Use #include \
<linux/io.h> instead of <asm/io.h>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In "usb: dwc3: remove special status request handling in ep0" I simplied
a few things and used the generic API for the status transfers. The bug
I introcuded here is that we queue now requests to dep[1] but we don't
clear that list in the stall+start case.
Actually we don't need to use dep[1] at all. We only did in the past to
talk to the correct endpoint (i.e. in or out). This is now take care of
in a diffent place within the ep0 code. So we could queue the in
transfers to dep[0] and don't use dep[1] at all.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The first access was correct, the second was wrong.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The GetStatus (STD)-request is handled the driver and uses a tiny hack
to send the two bytes long answer. This patch removes the custom hack
uses the normal usb_ep_queue() for that.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we stall and restart we have to reset also this flag to 0 as there is
nothing pending anymore.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sometimes the host might be trying to initiate Data or
Status phase for an older Control transfer. In such
situations we must STALL that transfer and restart
the state machine rather than letting such situation
go through the wire.
Signed-off-by: Felipe Balbi <balbi@ti.com>
I have talked to USB-IF about USB30CV issuing SetAddres()
with a device on Configured state and they have agreed on
changing USB30CV not to do so.
Adding back the STALL reply in such case and while at
that, also add a debugging message for an address which
is too large.
Signed-off-by: Felipe Balbi <balbi@ti.com>
our parameter structures need to be written to
HW, so instead of assuming little endian, we
convert those into bit shifts.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
DEPSTARTCFG for non-EP0 EPs must only be sent once per config
[ balbi@ti.com : changed config_start to start_config_issued ]
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some people think that this line is not compatible with the GPL. The
statement was required due to the Buenos Aires Convention and is now
deprecated. I remove it because it is said that it is pointless nowdays.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use "ep0in" and "ep0out" instead "ep1in" and "ep0out" which is confusing
and not consistent with the remaining output.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We already give requests back in dwc3_ep0_stall_and_restart() so
doing it again here will most likely corrupt the list.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The way it was before was really meaningless.
Now it looks saner.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need to care about direction on a two stage
transfer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to USB 3.0 Specification, a SetAddress()
while device is in Configured State has an unspecified
behavior (see Section 9.4.6). Still USB30CV wasn't
happy with my Stall reply.
To make that thing happy, just accept the SetAddress()
always. No problems have been observed thus far.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This flag will tell us which direction we're
expecting on the next (data or status) phase.
It will help us catching errors of host going
crazy and requesting data of the wrong direction.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Whenever we issue a Set Stall command on EP0,
the state machine will be restarted and Stall
is cleared automatically, when core receives
the next SETUP packet.
There's no need to track that EP0_STALL state.
Signed-off-by: Felipe Balbi <balbi@ti.com>
when we're going to issue Set Stall command,
we should clear DWC3_EP_STALL flag, but also
we should clear BUSY, HALTED and all others.
Signed-off-by: Felipe Balbi <balbi@ti.com>
John Youn