Pull input subsystem updates from Dmitry Torokhov:
"Mostly small fixups to PS/2 tochpad drivers (ALPS, Elantech,
Synaptics) to better deal with specific hardware"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - update the documentation
Input: elantech - provide a sysfs knob for crc_enabled
Input: elantech - report the middle button of the touchpad
Input: alps - ignore bad data on Dell Latitudes E6440 and E7440
Input: alps - allow up to 2 invalid packets without resetting device
Input: alps - ignore potential bare packets when device is out of sync
Input: elantech - fix crc_enabled for Fujitsu H730
Input: elantech - use elantech_report_trackpoint for hardware v4 too
Input: twl4030-pwrbutton - ensure a wakeup event is recorded.
Input: synaptics - add min/max quirk for Lenovo T440s
This button is treated as a wakeup source, so we need to initialise it
correctly.
Without the device_init_wakeup() call, dev->power.wakeup will
be NULL, and pm_wakeup_event() will do nothing.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"A bunch of fixes for minor defects reported by Coverity, a few driver
fixups and revert of i8042.nomux change so that we are once again
enable active MUX mode if box claims to support it"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: i8042 - disable active multiplexing by default"
Input: altera_ps2 - use correct type for irq return value
Input: altera_ps2 - write to correct register when disabling interrupts
Input: max77693-haptic - fix potential overflow
Input: psmouse - remove unneeded check in psmouse_reconnect()
Input: vsxxxaa - fix code dropping bytes from queue
Input: ims-pcu - fix dead code in ims_pcu_ofn_reg_addr_store()
Input: opencores-kbd - fix error handling
Input: wm97xx - adapt parameters to tosa touchscreen.
Input: i8042 - quirks for Fujitsu Lifebook A544 and Lifebook AH544
Input: stmpe-keypad - fix valid key line bitmask
Input: soc_button_array - update calls to gpiod_get*()
Expression haptic->pwm_dev->period * haptic->magnitude is of type
'unsigned int' and may overflow. We need to convert one of the operands
to u64 before multiplying, instead of casting result (potentially
overflown) to u64.
Reported by Coverity: CID 1248753
Acked-by : Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Coverity pointed out that at return point error is always 0 so the
conditional is not needed.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add the new flags argument to calls of (devm_)gpiod_get*().
Currently both forms (with or without the flags argument) are valid thanks
to transitional macros in <linux/gpio/consumer.h>. These macros will be
removed once all consumers are updated and the flags argument will become
compulsory.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull second round of input updates from Dmitry Torokhov:
"Mostly simple bug fixes, although we do have one brand new driver for
Microchip AR1021 i2c touchscreen.
Also there is the change to stop trying to use i8042 active
multiplexing by default (it is still possible to activate it via
i8042.nomux=0 on boxes that implement it)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - add Thrustmaster as Xbox 360 controller vendor
Input: xpad - add USB ID for Thrustmaster Ferrari 458 Racing Wheel
Input: max77693-haptic - fix state check in imax77693_haptic_disable()
Input: xen-kbdfront - free grant table entry in xenkbd_disconnect_backend
Input: alps - fix v4 button press recognition
Input: i8042 - disable active multiplexing by default
Input: i8042 - add noloop quirk for Asus X750LN
Input: synaptics - gate forcepad support by DMI check
Input: Add Microchip AR1021 i2c touchscreen
Input: cros_ec_keyb - add of match table
Input: serio - avoid negative serio device numbers
Input: avoid negative input device numbers
Input: automatically set EV_ABS bit in input_set_abs_params
Input: adp5588-keys - cancel workqueue in failure path
Input: opencores-kbd - switch to using managed resources
Input: evdev - fix EVIOCG{type} ioctl
The check to see whether the device is already disabled in
max77693_haptic_disable() was inversed, this change corrects it.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
xenkbd_disconnect_backend doesn't free grant table entry. This bug affects
live migration.
xenkbd_disconnect_backend uses gnttab_end_foreign_access_ref to handle
grant table entry which doesn't really free an entry.
Thus every time we do xenkbd_resume, grant table entry increses by one. As
an grant table entry occupies 8 bytes, an grant table page has at most 512
entries. Every 512 times we do xenkdb_resume, grant table pages increses by
one.
After around 3500 times of live migration, grant table pages will increase
by 7, causing too many pages to populate and hitting max_pages limit when
assigning pages.Thus assign_pages will fail, so will live migration.
Signed-off-by: Chang Huaixin <huaixin.chx@alibaba-inc.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- Add pvscsi frontend and backend drivers.
- Remove _PAGE_IOMAP PTE flag, freeing it for alternate uses.
- Try and keep memory contiguous during PV memory setup (reduces
SWIOTLB usage).
- Allow front/back drivers to use threaded irqs.
- Support large initrds in PV guests.
- Fix PVH guests in preparation for Xen 4.5
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJUNonmAAoJEFxbo/MsZsTRHAQH/inCjpCT+pkvTB0YAVfVvgMI
gUogT8G+iB2MuCNpMffGIt8TAVXwcVtnOLH9ABH3IBVehzgipIbIiVEM9YhjrYvU
1rgIKBpmZqSpjDHoIHpdHeCH67cVnRzA/PyoxZWLxPNmQ0t6bNf9yeAcCXK9PfUc
7EAblUDmPGSx9x/EUnOKNNaZSEiUJZHDBXbMBLllk1+5H1vfKnpFCRGMG0IrfI44
KVP2NX9Gfa05edMZYtH887FYyjFe2KNV6LJvE7+w7h2Dy0yIzf7y86t0l4n8gETb
plvEUJ/lu9RYzTiZY/RxgBFYVTV59EqT45brSUtoe2Jcp8GSwiHslTHdfyFBwSo=
=gw4d
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.18-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen updates from David Vrabel:
"Features and fixes:
- Add pvscsi frontend and backend drivers.
- Remove _PAGE_IOMAP PTE flag, freeing it for alternate uses.
- Try and keep memory contiguous during PV memory setup (reduces
SWIOTLB usage).
- Allow front/back drivers to use threaded irqs.
- Support large initrds in PV guests.
- Fix PVH guests in preparation for Xen 4.5"
* tag 'stable/for-linus-3.18-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (22 commits)
xen: remove DEFINE_XENBUS_DRIVER() macro
xen/xenbus: Remove BUG_ON() when error string trucated
xen/xenbus: Correct the comments for xenbus_grant_ring()
x86/xen: Set EFER.NX and EFER.SCE in PVH guests
xen: eliminate scalability issues from initrd handling
xen: sync some headers with xen tree
xen: make pvscsi frontend dependant on xenbus frontend
arm{,64}/xen: Remove "EXPERIMENTAL" in the description of the Xen options
xen-scsifront: don't deadlock if the ring becomes full
x86: remove the Xen-specific _PAGE_IOMAP PTE flag
x86/xen: do not use _PAGE_IOMAP PTE flag for I/O mappings
x86: skip check for spurious faults for non-present faults
xen/efi: Directly include needed headers
xen-scsiback: clean up a type issue in scsiback_make_tpg()
xen-scsifront: use GFP_ATOMIC under spin_lock
MAINTAINERS: Add xen pvscsi maintainer
xen-scsiback: Add Xen PV SCSI backend driver
xen-scsifront: Add Xen PV SCSI frontend driver
xen: Add Xen pvSCSI protocol description
xen/events: support threaded irqs for interdomain event channels
...
The DEFINE_XENBUS_DRIVER() macro looks a bit weird and causes sparse
errors.
Replace the uses with standard structure definitions instead. This is
similar to pci and usb device registration.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
ACPI device enumeration mechanism changed a lot since 3.16-rc1.
ACPI device objects with _HID will be enumerated to platform bus by default.
For the existing PNP drivers that probe the PNPACPI devices, the device ids
are listed explicitly in drivers/acpi/acpi_pnp.c.
But ACPI folks will continue their effort on shrinking this id list by
converting the PNP drivers to platform drivers, for the devices that don't
belong to PNP bus in nature.
Signed-off-by: Jin Yao <yao.jin@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
make C=2 CHECK="scripts/coccicheck" MODE=report COCCI=scripts/coccinelle/misc/irqf_oneshot.cocci ./drivers/input/misc/palmas-pwrbutton.o
Reports:
drivers/input/misc/palmas-pwrbutton.c:213:9-29: ERROR: Threaded IRQ with no primary handler requested without IRQF_ONESHOT
Palmas power button just needs threaded IRQ handler since I2C operations
are involved and there is nothing in non-threaded primary handler we could
do.
So mark the request with ONESHOT as it should have been done in these
cases.
Fixes: adff5962fd ("Input: introduce palmas-pwrbutton")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver to supports the haptic controller on MAX77693 Multifunction
device with PMIC, CHARGER, LED, MUIC, HAPTIC.
This driver supports external pwm and LRA (Linear Resonant Actuator) motor.
User can control the haptic device via force feedback framework.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Many palmas family of PMICs have support for interrupt based power button.
This allows the device to notify the processor of external push button
events over the shared palmas interrupt. However, this event is generated
only during a "press" operation. Software is supposed to poll(sigh!) for
detecting a release event.
The PMIC also supports ability to power off independent of the software
decisions when the button is pressed for a long duration if the PMIC is
appropriately configured on the platform.
Even though the function is similar to twl4030_pwrbutton, it is
substantially different in operation to belong to a new driver of it's own.
Based on original work done by Girish S Ghongdemath <girishsg@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Adding support for the DRV2667 haptic driver. This device has the ability
to store vibration patterns in RAM and execute them once the GO bit is set.
The initial driver sets a basic waveform in the first waveform sequence and
will play the waveform when the GO bit is set and will continously play the
waveform until the GO bit is unset.
Data sheet is here: http://www.ti.com/product/drv2667
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUA8qAAAoJEHm+PkMAQRiGRNwH/194A8PirGSXmM83dMoW2RHU
j597TT0frxfHiDDcHpIYZBg5Z0qV6ZvY2982HzYJr3eEDzXYzz0nI5TlNBeNPy1i
yRb2c74/BKvIvSSj9s4MZ9918HbYWE7L1bJAoVs7uc50iANgVSuesOrWVzTylSor
/cNwFV1GMjIVEGwP1/lZy40NQD92ZG1kkttzMnrrH9E5TQ7UK+DIAfJViFIYv8Cp
fw2U5VKrZ7qZm0XlOq5keN/mD6lKicSBTlPdvSICHkzOBbUlS35tTnW3co9jmpba
XUKNqM4YvXJWzbgrAGT8CHBaQTOMylRO/a2AOIwqOciODJJB0CqfJ0CtHUffOnE=
=yN6O
-----END PGP SIGNATURE-----
Merge tag 'v3.17-rc3' into next
Sync with mainline to bring in Chrome EC changes.
Add a check to ensure that LRA libraries are not mixed with the ERM mode.
If ERM mode and the Library is empty "OR" the LRA library then exit, as the
LRA and empty libraries are not applicable for the ERM actuator.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Removing some #defines that are not and should never be used pertaining to
I2C.
Removing:
define DRV260X_ALLOWED_R_BYTES 25
define DRV260X_ALLOWED_W_BYTES 2
define DRV260X_MAX_RW_RETRIES 5
define DRV260X_I2C_RETRY_DELAY 10
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add the TI drv260x haptics/vibrator driver. This device uses the input
force feedback to produce a wave form to driver an ERM or LRA actuator
device.
The initial driver supports the devices real time playback mode. But the
device has additional wave patterns in ROM. This functionality will be
added in future patchsets.
Product data sheet is located here: http://www.ti.com/product/drv2605
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- big update to Wacom driver by Benjamin Tissoires, converting it to
HID infrastructure and unifying USB and Bluetooth models
- large update to ALPS driver by Hans de Goede, which adds support for
newer touchpad models as well as cleans up and restructures the code
- more changes to Atmel MXT driver, including device tree support
- new driver for iPaq x3xxx touchscreen
- driver for serial Wacom tablets
- driver for Microchip's CAP1106
- assorted cleanups and improvements to existing drover and input core
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (93 commits)
Input: wacom - update the ABI doc according to latest changes
Input: wacom - only register once the MODULE_* macros
Input: HID - remove hid-wacom Bluetooth driver
Input: wacom - add copyright note and bump version to 2.0
Input: wacom - remove passing id for wacom_set_report
Input: wacom - check for bluetooth protocol while setting OLEDs
Input: wacom - handle Intuos 4 BT in wacom.ko
Input: wacom - handle Graphire BT tablets in wacom.ko
Input: wacom - prepare the driver to include BT devices
Input: hyperv-keyboard - register as a wakeup source
Input: imx_keypad - remove ifdef round PM methods
Input: jornada720_ts - get rid of space indentation and use tab
Input: jornada720_ts - switch to using managed resources
Input: alps - Rushmore and v7 resolution support
Input: mcs5000_ts - remove ifdef around power management methods
Input: mcs5000_ts - protect PM functions with CONFIG_PM_SLEEP
Input: ads7846 - release resources on failure for clean exit
Input: wacom - add support for 0x12C ISDv4 sensor
Input: atmel_mxt_ts - use deep sleep mode when stopped
ARM: dts: am437x-gp-evm: Update binding for touchscreen size
...
The memory are mapped using of_ioremap() which is
an indication this is sbus memory.
Shift all uses of inb/outb to the sbus variants.
The inb/outb methods uses ASI_PHYS_BYPASS_EC_E_L,
whereas sbus_ variants uses ASI_PHYS_BYPASS_EC_E.
The difference is if the reads/writes are done in
native or little endian.
But for byte reads/writes there is no difference
so this does not matter for inb/outb - and this
driver only uses the byte variants.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ioctl is the counterpart to EVIOCGVERSION and returns the
uinput-version the kernel was compiled with.
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This moves basic checks and setup from uinput_setup_device() into
uinput_validate_absbits() to make it easier to use. This way, we can call
it from other places without copying the boilerplate code.
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Per license_is_gpl_compatible(), the MODULE_LICENSE() string for GPL v2 is
"GPL v2", not "GPLv2". Use "GPL v2" so this module doesn't taint the
kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's start checking return value of regulator_enable and pwm_enable to
avoid errors. Fixes the following warning:
drivers/input/misc/max8997_haptic.c:185:19: warning: ignoring return value of ‘regulator_enable’, declared with attribute warn_unused_result [-Wunused-result]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In case allocation via usb_alloc_coherent() fails in ims_pcu_buffers_alloc(),
the function jumps to the exit path without initializing local variable
'error' that is used as return value. Detected by Coverity - CID 1016531.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTbTZoAAoJEHm+PkMAQRiGLssH/3Rv6e9rAkEw9Ey0ymwGsCvf
6DEAcSgaWEyYWEU+DmkEQ3hbiOyESHFOsWE4zA2F5WY0w2Xsr+wDCS+14WCN6NHT
6sxSYGj1hd+ni6GhlGxfRpUXtY59h7TKHaaHYKPIOsO4OWXVeD53trpq416kvqal
zWkFOWeiEyeJnNKv0z0+5QWTeFDjTd1YawWcK/8kFez1Y4BXBECTgKoJaEcvowfU
j7oQ0BJxtLlxFgCB84bZTUbGuyn1x9FiS7Z2w9JcqSkTLMabFjsbA15eZIV66N4s
boaxlRvyvelR09eiiYYqOLxUmeEi1wRqtAM3yln1Y5/MX+DAmf5/sylqKtC5eLg=
=ezkr
-----END PGP SIGNATURE-----
Merge tag 'v3.15-rc5' into next
Merge with Linux 3.15-rc5 to sync up Wacom and other changes.
If the debounce time is 0 our usage of ilog2() later on in this driver will
cause undefined behavior. If CONFIG_OF=n this fact is evident to the
compiler, and it emits a call to ____ilog2_NaN() which doesn't exist. Fix
this by setting a sane default for debounce and failing to probe if
debounce is 0 in the DT.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch simplifies GPIO handling in the driver by using GPIO functions
based on descriptors. As a result this driver now can be used for boards
without DT support.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Using devm_regulator_bulk_get() and devm_input_allocate_device() can make
the code cleaner and smaller as we do not need to manually free resources
the error and remove paths.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem fixes from Dmitry Torokhov:
"Just a few fixups to various drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - fix touchpad initialization on Gigabyte U2442
Input: tca8418 - fix loading this driver as a module from a device tree
Input: bma150 - extend chip detection for bma180
Input: atkbd - fix keyboard not working on some LG laptops
Input: synaptics - add min/max quirk for ThinkPad Edge E431
This driver has been used while on the OpenPhoenux GTA04 with a BMA180.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"The main change is that we now publish "firmware ID" for the serio
devices to help userspace figure out the kind of touchpads it is
dealing with: i8042 will export PS/2 port's PNP IDs as firmware IDs.
You will also get more quirks for Synaptics touchpads in various
Lenovo laptops, a change to elantech driver to recognize even more
models, and fixups to wacom and couple other drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - add support for newer elantech touchpads
Input: soc_button_array - fix a crash during rmmod
Input: synaptics - add min/max quirk for ThinkPad T431s, L440, L540, S1 Yoga and X1
Input: synaptics - report INPUT_PROP_TOPBUTTONPAD property
Input: Add INPUT_PROP_TOPBUTTONPAD device property
Input: i8042 - add firmware_id support
Input: serio - add firmware_id sysfs attribute
Input: wacom - handle 1024 pressure levels in wacom_tpc_pen
Input: wacom - references to 'wacom->data' should use 'unsigned char*'
Input: wacom - override 'pressure_max' with value from HID_USAGE_PRESSURE
Input: wacom - use full 32-bit HID Usage value in switch statement
Input: wacom - missed the last bit of expresskey for DTU-1031
Input: ads7846 - fix device usage within attribute show
Input: da9055_onkey - remove use of regmap_irq_get_virq()
When the system has zero or one button available, trying to rmmod
soc_button_array will cause crash. Fix this by properly handling -ENODEV
in probe().
Signed-off-by: Lejun Zhu <lejun.zhu@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Using platform_get_irq_byname() to retrieve the IRQ number returns the
VIRQ number rather than the local IRQ number for the device. Passing that
value then into regmap_irq_get_virq() causes a failure because the
function is expecting the local IRQ number (e.g. 0, 1, 2, 3, etc).
This patch removes use of regmap_irq_get_virq() to prevent this failure
from happening.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The legacy HAVE_PWM Kconfig symbol is finally being retired. Thanks a
lot to Sascha Hauer for doing that.
Three new drivers are added: Freescale FTM, Cirrus Logic CLPS711X and
Intel Low Power Subsystem.
An assortment of fixes and cleanups rounds things off for this release
cycle.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=pbF+
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"The legacy HAVE_PWM Kconfig symbol is finally being retired. Thanks a
lot to Sascha Hauer for doing that.
Three new drivers are added: Freescale FTM, Cirrus Logic CLPS711X and
Intel Low Power Subsystem.
An assortment of fixes and cleanups rounds things off for this release
cycle"
* tag 'pwm/for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: pxa: Constify OF match table
pwm: pxa: Fix typo "pwm" -> "PWM"
Revert "pwm: pxa: Use of_match_ptr()"
pwm: add support for Intel Low Power Subsystem PWM
pwm: Add CLPS711X PWM support
pwm: atmel: correct CDTY calculation
pwm: atmel: Fix polarity handling
Documentation: Add device tree bindings for Freescale FTM PWM.
pwm: Add Freescale FTM PWM driver support
pwm: pxa: Use of_match_ptr()
pwm: samsung: Use SIMPLE_DEV_PM_OPS macro
pwm: renesas-tpu: Add dependency on HAS_IOMEM
pwm: Remove obsolete HAVE_PWM Kconfig symbol
These cleanup patches are mainly move stuff around and should all
be harmless. They are mainly split out so that other branches can
be based on top to avoid conflicts.
Notable changes are:
* We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used. (Uwe Kleine-König)
* The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions. (Kumar Gala)
* A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
* Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
* mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
* at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GcBb
-----END PGP SIGNATURE-----
Merge tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"These cleanup patches are mainly move stuff around and should all be
harmless. They are mainly split out so that other branches can be
based on top to avoid conflicts.
Notable changes are:
- We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used (Uwe Kleine-König)
- The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions (Kumar Gala)
- A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
- Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
- mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
- at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people)"
* tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (89 commits)
ARM: hisi: select HAVE_ARM_SCU only for SMP
ARM: efm32: allow uncompress debug output
ARM: prima2: build reset code standalone
ARM: at91: add PWM clock
ARM: at91: move sam9261 SoC to common clk
ARM: at91: prepare common clk transition for sam9261 SoC
ARM: at91: updated the at91_dt_defconfig with support for the ADS7846
ARM: at91: dt: sam9261: Device Tree support for the at91sam9261ek
ARM: at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs
ARM: at91: dt: Add at91sam9261 dt SoC support
ARM: at91: switch sam9rl to common clock framework
ARM: at91/dt: define main clk frequency of at91sam9rlek
ARM: at91/dt: define at91sam9rl clocks
ARM: at91: prepare common clk transition for sam9rl SoCs
ARM: at91: prepare sam9 dt boards transition to common clk
ARM: at91: dt: sam9rl: Device Tree for the at91sam9rlek
ARM: at91/defconfig: Add the sam9rl to the list of DT-enabled SOCs
ARM: at91: Add at91sam9rl DT SoC support
ARM: at91: prepare at91sam9rl DT transition
ARM: at91/defconfig: refresh at91sam9260_9g20_defconfig
...
Pull input updates from Dmitry Torokhov:
"The first round of updates for the input subsystem.
Just new drivers and existing driver fixes, no core changes except for
the new uinput IOCTL to allow userspace to fetch sysfs name of the
input device that was created"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (43 commits)
Input: edt-ft5x06 - add a missing condition
Input: appletouch - fix jumps when additional fingers are detected
Input: appletouch - implement sensor data smoothing
Input: add driver for SOC button array
Input: pm8xxx-vibrator - add DT match table
Input: pmic8xxx-pwrkey - migrate to DT
Input: pmic8xxx-keypad - migrate to DT
Input: pmic8xxx-keypad - migrate to regmap APIs
Input: pmic8xxx-keypad - migrate to devm_* APIs
Input: pmic8xxx-keypad - fix build by removing gpio configuration
Input: add new driver for ARM CLPS711X keypad
Input: edt-ft5x06 - add support for M09 firmware version
Input: edt-ft5x06 - ignore touchdown events
Input: edt-ft5x06 - adjust delays to conform datasheet
Input: edt-ft5x06 - add DT support
Input: edt-ft5x06 - several cleanups; no functional change
Input: appletouch - dial back fuzz setting
Input: remove obsolete tnetv107x drivers
Input: sirfsoc-onkey - set the capability of reporting KEY_POWER
Input: da9052_onkey - use correct register bit for key status
...