mirror of https://gitee.com/openkylin/linux.git
642 Commits
| Author | SHA1 | Message | Date |
|---|---|---|---|
Linus Torvalds
|
7c0f6ba682 |
Replace <asm/uaccess.h> with <linux/uaccess.h> globally
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
Rafał Miłecki
|
64ad46379f |
mtd: bcm47xxsflash: use uncached MMIO access for BCM53573
BCM53573 is a new series of Broadcom's SoCs. It's based on ARM and uses this old ChipCommon-based flash access. Early tests resulted in flash corruptions that were tracked down to using cached MMIO for flash read access. Switch to ioremap_nocache conditionally to support BCM53573 and don't break performance on old MIPS devices. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> |
|
|
Linus Torvalds
|
affe8a2abd |
MTD updates for v4.8:
NAND:
Updates from Boris:
"""
This pull request contains only one notable change:
* Addition of the MTK NAND controller driver
And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
* A few fixes/improvements for the xway NAND controller driver
* A few fixes for the sunxi NAND controller driver
* Support for DMA in the sunxi NAND driver
* Support for the sunxi NAND controller IP embedded in A23/A33 SoCs
* Addition for bitflips detection in erased pages to the brcmnand driver
* Support for new brcmnand IPs
* Update of the OMAP-GPMC binding to support DMA channel description
"""
In addition, some small fixes around error handling, etc., as well as one
long-standing corner case issue (2.6.20, I think?) with writing 1 byte less
than a page.
NOR:
* Rework some error handling on reads and writes, so we can better handle (for
instance) SPI controllers which have limitations on their maximum transfer size
* Add new Cadence Quad SPI flash controller driver
* Add new Atmel QSPI flash controller driver
* Add new Hisilicon SPI flash controller driver
* Support a few new flash, and update supported features on others
* Fix the logic used for detecting a fully-unlocked flash
And other miscellaneous small fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HQr0
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160801' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"NAND:
Quoting Boris:
'This pull request contains only one notable change:
- Addition of the MTK NAND controller driver
And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
- A few fixes/improvements for the xway NAND controller driver
- A few fixes for the sunxi NAND controller driver
- Support for DMA in the sunxi NAND driver
- Support for the sunxi NAND controller IP embedded in A23/A33 SoCs
- Addition for bitflips detection in erased pages to the brcmnand driver
- Support for new brcmnand IPs
- Update of the OMAP-GPMC binding to support DMA channel description'
In addition, some small fixes around error handling, etc., as well
as one long-standing corner case issue (2.6.20, I think?) with
writing 1 byte less than a page.
NOR:
- rework some error handling on reads and writes, so we can better
handle (for instance) SPI controllers which have limitations on
their maximum transfer size
- add new Cadence Quad SPI flash controller driver
- add new Atmel QSPI flash controller driver
- add new Hisilicon SPI flash controller driver
- support a few new flash, and update supported features on others
- fix the logic used for detecting a fully-unlocked flash
And other miscellaneous small fixes"
* tag 'for-linus-20160801' of git://git.infradead.org/linux-mtd: (60 commits)
mtd: spi-nor: don't build Cadence QuadSPI on non-ARM
mtd: mtk-nor: remove duplicated include from mtk-quadspi.c
mtd: nand: fix bug writing 1 byte less than page size
mtd: update description of MTD_BCM47XXSFLASH symbol
mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller
mtd: spi-nor: Bindings for Cadence Quad SPI Flash Controller driver
mtd: nand: brcmnand: Change BUG_ON in brcmnand_send_cmd
mtd: pmcmsp-flash: Allocating too much in init_msp_flash()
mtd: maps: sa1100-flash: potential NULL dereference
mtd: atmel-quadspi: add driver for Atmel QSPI controller
mtd: nand: omap2: fix return value check in omap_nand_probe()
Documentation: atmel-quadspi: add binding file for Atmel QSPI driver
mtd: spi-nor: add hisilicon spi-nor flash controller driver
mtd: spi-nor: support dual, quad, and WP for Gigadevice
mtd: spi-nor: Added support for n25q00a.
memory: Update dependency of IFC for Layerscape
mtd: nand: jz4780: Update MODULE_AUTHOR email address
mtd: nand: sunxi: prevent a small memory leak
mtd: nand: sunxi: add reset line support
mtd: nand: sunxi: update DT bindings
...
|
|
|
Linus Torvalds
|
bad60e6f25 |
powerpc updates for 4.8 # 1
Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder. from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King, Geliang
Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman, Michael Ellerman,
Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Z5kM
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael
Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from
Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call
from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB
from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev
Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin
Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj
Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton
Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus
Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from
Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from
Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin
Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King,
Geliang Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman,
Michael Ellerman, Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO"
* tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (263 commits)
powerpc/mm: Parenthesise IS_ENABLED() in if condition
tty/hvc: Use opal irqchip interface if available
tty/hvc: Use IRQF_SHARED for OPAL hvc consoles
selftests/powerpc: exec() with suspended transaction
powerpc: Improve comment explaining why we modify VRSAVE
powerpc/mm: Drop unused externs for hpte_init_beat[_v3]()
powerpc/mm: Rename hpte_init_lpar() and move the fallback to a header
powerpc/mm: Fix build break when PPC_NATIVE=n
crypto: vmx - Convert to CPU feature based module autoloading
powerpc: Add module autoloading based on CPU features
powerpc/powernv/ioda: Fix endianness when reading TCEs
powerpc/mm: Add memory barrier in __hugepte_alloc()
powerpc/modules: Never restore r2 for a mprofile-kernel style mcount() call
powerpc/ftrace: Separate the heuristics for checking call sites
powerpc: Merge 32-bit and 64-bit setup_arch()
powerpc/64: Make a few boot functions __init
powerpc: Re-order setup_panic()
powerpc: Re-order the call to smp_setup_cpu_maps()
powerpc/32: Move cache info inits to a separate function
powerpc/64: Move the content of setup_system() to setup_arch()
...
|
|
|
Rafał Miłecki
|
efacc69913 |
mtd: add arch dependency for MTD_BCM47XXSFLASH symbol
We dropped strict MIPS dependency for bcm47xxsflash driver in: commit |
|
|
Rafał Miłecki
|
0a526341fe |
mtd: update description of MTD_BCM47XXSFLASH symbol
For years now we support writing to BCMA SoC serial flash, so don't describe this driver as providing read-only support anymore. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> |
|
|
Ben Hutchings
|
ef158bdf83 |
mtd: Remove unused symbol CONFIG_MTDRAM_ABS_POS
This has been unused, except as the condition for a fatal error, since
commit
|
|
|
Suraj Jitindar Singh
|
d0226d315d |
powerpc/opal: Add inline function to get rc from an ASYNC_COMP opal_msg
An opal_msg of type OPAL_MSG_ASYNC_COMP contains the return code in the params[1] struct member. However this isn't intuitive or obvious when reading the code and requires that a user look at the skiboot documentation or opal-api.h to verify this. Add an inline function to get the return code from an opal_msg and update call sites accordingly. Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> |
|
|
Michal Suchanek
|
9519379625 |
mtd: m25p80: read in spi_max_transfer_size chunks
Take into account transfer size limitation of SPI master. Signed-off-by: Michal Suchanek <hramrach@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Michal Suchanek <hramrach@gmail.com> Tested-by: Michal Suchanek <hramrach@gmail.com> |
|
|
Michal Suchanek
|
2dd087b169 |
mtd: spi-nor: stop passing around retlen
Do not pass retlen to hardware driver read/write functions. Update it in spi-nor generic driver instead. Signed-off-by: Michal Suchanek <hramrach@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Tested-by Cyrille Pitchen <cyrille.pitchen@atmel.com> Acked-by: Michal Suchanek <hramrach@gmail.com> Tested-by: Michal Suchanek <hramrach@gmail.com> |
|
|
Michal Suchanek
|
1992297b08 |
mtd: m25p80: return amount of data transferred or error in read/write
Add checking of SPI transfer errors and return them from read/write functions. Also return the amount of data transferred. Signed-off-by: Michal Suchanek <hramrach@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Michal Suchanek <hramrach@gmail.com> Tested-by: Michal Suchanek <hramrach@gmail.com> |
|
|
Michal Suchanek
|
59451e1233 |
mtd: spi-nor: change return value of read/write
Change the return value of spi-nor device read and write methods to allow returning amount of data transferred and errors as read(2)/write(2) does. Also, start handling positive returns in spi_nor_read(), since we want to convert drivers to start returning the read-length both via *retlen and the return code. (We don't need to do the same transition process for spi_nor_write(), since ->write() didn't used to have a return code at all.) Signed-off-by: Michal Suchanek <hramrach@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Tested-by Cyrille Pitchen <cyrille.pitchen@atmel.com> Acked-by: Michal Suchanek <hramrach@gmail.com> Tested-by: Michal Suchanek <hramrach@gmail.com> |
|
|
Linus Torvalds
|
8bc4d5f394 |
MTD updates for v4.7:
First cycle with Boris as NAND maintainer! Many (most) bullets stolen from him.
Generic:
* Migrated NAND LED trigger to be a generic MTD trigger
NAND:
* Introduction of the "ECC algorithm" concept, to avoid overloading the ECC
mode field too much more
* Replaced the nand_ecclayout infrastructure with something a little more
flexible (finally!) and future proof
* Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some of
this into their own tree as well
* Prepare the sunxi NAND driver to receive DMA support
* Handle bitflips in erased pages on GPMI revisions that do not support
this in hardware.
SPI NOR:
* Start using the spi_flash_read() API for SPI drivers that support it (i.e.,
SPI drivers with special memory-mapped flash modes)
And other small scattered improvments.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=J6KN
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"First cycle with Boris as NAND maintainer! Many (most) bullets stolen
from him.
Generic:
- Migrated NAND LED trigger to be a generic MTD trigger
NAND:
- Introduction of the "ECC algorithm" concept, to avoid overloading
the ECC mode field too much more
- Replaced the nand_ecclayout infrastructure with something a little
more flexible (finally!) and future proof
- Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some
of this into their own tree as well
- Prepare the sunxi NAND driver to receive DMA support
- Handle bitflips in erased pages on GPMI revisions that do not
support this in hardware.
SPI NOR:
- Start using the spi_flash_read() API for SPI drivers that support
it (i.e., SPI drivers with special memory-mapped flash modes)
And other small scattered improvments"
* tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd: (155 commits)
mtd: spi-nor: support GigaDevice gd25lq64c
mtd: nand_bch: fix spelling of "probably"
mtd: brcmnand: respect ECC algorithm set by NAND subsystem
gpmi-nand: Handle ECC Errors in erased pages
Documentation: devicetree: deprecate "soft_bch" nand-ecc-mode value
mtd: nand: add support for "nand-ecc-algo" DT property
mtd: mtd: drop NAND_ECC_SOFT_BCH enum value
mtd: drop support for NAND_ECC_SOFT_BCH as "soft_bch" mapping
mtd: nand: read ECC algorithm from the new field
mtd: nand: fsmc: validate ECC setup by checking algorithm directly
mtd: nand: set ECC algorithm to Hamming on fallback
staging: mt29f_spinand: set ECC algorithm explicitly
CRIS v32: nand: set ECC algorithm explicitly
mtd: nand: atmel: set ECC algorithm explicitly
mtd: nand: davinci: set ECC algorithm explicitly
mtd: nand: bf5xx: set ECC algorithm explicitly
mtd: nand: omap2: Fix high memory dma prefetch transfer
mtd: nand: omap2: Start dma request before enabling prefetch
mtd: nandsim: add __init attribute
mtd: nand: move of_get_nand_xxx() helpers into nand_base.c
...
|
|
|
Brian Norris
|
2cbaf5491c |
This pull request contains the following infrastructure changes:
* introduction of the ECC algo concept to extend the ECC mode one * replacement of the nand_ecclayout infrastructure by something more future-proof. * addition of an mtd-activity led trigger to replace the nand-activity one And a bunch of specific NAND driver improvements/fixes. Here are the changes that are worth mentioning: * rework of the OMAP GPMC and NAND drivers * prepare the sunxi NAND driver to receive DMA support * handle bitflips in erased pages on GPMI revisions that do not support this in hardware. -----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQIcBAABAgAGBQJXK8LCAAoJEGXtNgF+CLcAX/AP/A/pgi/MZU8+T8mCiq3xBu97 bLjdn+fSVn834YEjGoumD5bvTANisbDOy/K9MpcLT6e+jXdKZbgNNneoJLmCAVVW 0hraHaX3zU28G9SRe7VasKJSMglN8+7r/+PR6/NBH0pAHv7BYsxfREC7Jf7LMTIb PNrywfIGd/NPhI0stgL0+rzT3Z3GVO9p2y/OLJ7AmExGQO7wVvyQW/WYpk/ncEwG wSiWLMR7tfEdmrkvpvzo+B0ZuBENCWz/HAhKJ6mCZdTbVMdFPsufG2pTnUaXrxLg gRdkdj09S5b5VcqufjtSSRopHX9H5FFAzNmMPgDgCTiPu1b3wwD0CyxNfevewhTi AFRZrq5z8TUm3/6Sh0g2Pti3Nr7Tm1rodpR1oaTMrMT1avrerTstenfi+0XaWEce LiBSivbQizUsmaNtVlEYD0wEQoLN4Kmqhe6sD/24n92PpFPIxYbwdti4ybwpY7N1 8QwWNe8UFryG+7eAUvw69Yr6eetr3tAsjq2vqq0wblNDLH9kACFVrpijAxCX8pYK PB5RUDLmJlQy3Jyq4eUylr+v3cLgkQ2NWP49tgsIT4nsbYpi9BCum0pfeD2kAbQh mIpy/vlL0D5bqtriTNJjM2IhaJ8vyRNPo9cOgqoMRyLZDgGAn/XvecMVziZ2L0HK x0DZ/HX4Sec4RNRSvfQ5 =PYza -----END PGP SIGNATURE----- Merge tag 'nand/for-4.7' of github.com:linux-nand/linux Updates from Boris Brezillon: This pull request contains the following infrastructure changes: * introduction of the ECC algo concept to extend the ECC mode one * replacement of the nand_ecclayout infrastructure by something more future-proof. * addition of an mtd-activity led trigger to replace the nand-activity one And a bunch of specific NAND driver improvements/fixes. Here are the changes that are worth mentioning: * rework of the OMAP GPMC and NAND drivers * prepare the sunxi NAND driver to receive DMA support * handle bitflips in erased pages on GPMI revisions that do not support this in hardware. * tag 'nand/for-4.7' of github.com:linux-nand/linux: (152 commits) mtd: brcmnand: respect ECC algorithm set by NAND subsystem gpmi-nand: Handle ECC Errors in erased pages Documentation: devicetree: deprecate "soft_bch" nand-ecc-mode value mtd: nand: add support for "nand-ecc-algo" DT property mtd: mtd: drop NAND_ECC_SOFT_BCH enum value mtd: drop support for NAND_ECC_SOFT_BCH as "soft_bch" mapping mtd: nand: read ECC algorithm from the new field mtd: nand: fsmc: validate ECC setup by checking algorithm directly mtd: nand: set ECC algorithm to Hamming on fallback staging: mt29f_spinand: set ECC algorithm explicitly CRIS v32: nand: set ECC algorithm explicitly mtd: nand: atmel: set ECC algorithm explicitly mtd: nand: davinci: set ECC algorithm explicitly mtd: nand: bf5xx: set ECC algorithm explicitly mtd: nand: omap2: Fix high memory dma prefetch transfer mtd: nand: omap2: Start dma request before enabling prefetch mtd: nandsim: add __init attribute mtd: nand: move of_get_nand_xxx() helpers into nand_base.c mtd: nand: sh_flctl: rely on generic DT parsing done in nand_scan_ident() mtd: nand: mxc: rely on generic DT parsing done in nand_scan_ident() ... |
|
|
Julia Lawall
|
abbbc60a0c |
mtd: pmc551: add __init attribute
Add __init attribute on a function that is only called from other __init functions and that is not inlined, at least with gcc version 4.8.4 on an x86 machine with allyesconfig. Currently, the function is put in the .text.unlikely segment. Declaring it as __init will cause it to be put in the .init.text and to disappear after initialization. The result of objdump -x on the function before the change is as follows: 00000000000000c6 l F .text.unlikely 000000000000091c fixup_pmc551 And after the change it is as follows: 0000000000000000 l F .init.text 0000000000000917 fixup_pmc551 Done with the help of Coccinelle. The semantic patch checks for local static non-init functions that are called from an __init function and are not called from any other function. Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Brian Norris <computersforpeace@gmail.com> |
|
|
Boris Brezillon
|
1bd0b24737 |
mtd: docg3: switch to mtd_ooblayout_ops
Replace the nand_ecclayout definition by the equivalent mtd_ooblayout_ops definition. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> |
|
|
Boris Brezillon
|
06af3b023c |
mtd: docg3: use mtd_set_ecclayout() where appropriate
Use the mtd_set_ecclayout() helper instead of directly assigning the mtd->ecclayout field. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> |
|
|
Vignesh R
|
08922f6448 |
mtd: devices: m25p80: add support for mmap read request
Certain SPI controllers may provide accelerated hardware interface to read from m25p80 type flash devices in order to provide better read performance. SPI core supports such devices with spi_flash_read() API. Call spi_flash_read(), if supported, to make use of such interface. Signed-off-by: Vignesh R <vigneshr@ti.com> [Brian: add memset()] Signed-off-by: Brian Norris <computersforpeace@gmail.com> |
|
|
Kirill A. Shutemov
|
09cbfeaf1a |
mm, fs: get rid of PAGE_CACHE_* and page_cache_{get,release} macros
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
Brian Norris
|
5651d6aaf4 |
mtd: bcm47xxsflash: use ioremap_cache() instead of KSEG0ADDR()
Using KSEG0ADDR makes code highly MIPS dependent and not portable.
Thanks to the fix
|
|
|
Boris BREZILLON
|
f5b8aa78ef |
mtd: kill the ecclayout->oobavail field
ecclayout->oobavail is just redundant with the mtd->oobavail field. Moreover, it prevents static const definition of ecc layouts since the NAND framework is calculating this value based on the ecclayout->oobfree field. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> |
|
|
Alexander Stein
|
c67682c5e0 |
mtd: mtdram: Add parameter for setting writebuf size
ubifs uses the write buffer size in recovery algorithm. When inspecting an unclean ubifs recovery fails with writebuf size 64 in mtdram while recovery on actual mtd device with writebuf size of 1024 succeeds. So add a parameter for setting this property. Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com> Reviewed-by: Richard Weinberger <richard@nod.at> Signed-off-by: Brian Norris <computersforpeace@gmail.com> |
|
|
Brian Norris
|
c1711b297f |
mtd: m25p80: replace leftover "nor-jedec" with "spi-nor" in comments
I overlooked a few comments in commit
|
|
|
Brian Norris
|
de57732da8 |
mtd: m25p80: fix module autoloading for "jedec, spi-nor" and "spi-nor"
Commit
|
|
|
Brian Norris
|
cd78ea02dc |
mtd: m25p80: drop erase() callback
Just use the spi-nor default instead. Signed-off-by: Brian Norris <computersforpeace@gmail.com> |
|
|
Brian Norris
|
617f41836c |
Linux 4.4-rc1
-----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQEcBAABAgAGBQJWSSq2AAoJEHm+PkMAQRiGIpQH/2Ro7UPwLARfZyd7GKpCRd/D y1aJEk9GaEywkGKPd/Hf3XU+/9vxqyTWhkvpKHkGAFqzuYvw2rSE1JZnGfA+dyt/ 1R/WSKM8f3VL2xmNmRJCXH+zn3W2u8Cvk0oj8VN0hseXByQfCT4HfoHiFrNwuo/9 63f93Dqsai1G3CBy+/HSPEv5CGR+7yeTJFWS0hQK4kc3prmitI93C5PZkyePyAId wrgKo320rIcNL/lEAbMFEBimAqluIjGvdrR9FK6w3F+OwSlTV1HdSwTzNjxwdpP5 aRKNHZMdsGlShsn12Wsp+mjVFpi9OrT8Askq+/GTDsG+9QMia/gUKC21K9b6UxM= =byS9 -----END PGP SIGNATURE----- Merge v4.4-rc1 into MTD development Sync up with the upstream development. Signed-off-by: Brian Norris <computersforpeace@gmail.com> |
|
|
Brian Norris
|
004b5e6031 |
mtd: drop unnecessary partition parser data
We should assign the MTD dev.of_node instead of the parser data field. This gets us the equivalent partition parser behavior with fewer special fields and parameter passing. Also convert several of these to mtd_device_register(), since we don't need the 2nd and 3rd parameters anymore. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> |
|
|
Brian Norris
|
df02c885f8 |
mtd: spi-nor: drop unnecessary partition parser data
Now that the SPI-NOR/MTD framework pass the 'flash_node' through to the partition parsing code, we don't have to do it ourselves. Also convert to mtd_device_register(), since we don't need the 2nd and 3rd parameters anymore. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> |
|
|
Brian Norris
|
9c7d787508 |
mtd: spi-nor: convert to spi_nor_{get, set}_flash_node()
Used semantic patch with 'make coccicheck MODE=patch COCCI=script.cocci': ---8<---- virtual patch @@ struct spi_nor b; struct spi_nor *c; expression d; @@ ( -(b).flash_node = (d) +spi_nor_set_flash_node(&b, d) | -(c)->flash_node = (d) +spi_nor_set_flash_node(c, d) ) ---8<---- And a manual conversion for the one use of spi_nor_get_flash_node(). Signed-off-by: Brian Norris <computersforpeace@gmail.com> Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> |
|
|
Linus Torvalds
|
02f0d3f758 |
MTD updates for 4.4-rc1:
Core
* WARN (in some cases) when a struct mtd_info is registered multiple times;
in the past this was "supported", but it's still error prone for future
development. There's only one ugly case of this left in the tree (that
we're aware of) and the owners are aware of the problems there.
* fix potential deadlock in the blkdev removal path
NOTE: the (potential) deadlock was introduced in a for-stable patch. This
one is also marked for -stable.
* ioctl(BLKPG) compat_ioctl support; resolves issues with 32-bit user space
vs. 64-bit kernel space
* Set MTD parent device correctly throughout the tree, so the tree structure
appears correctly in sysfs; many drivers were missing this (soft)
requirement
* Move device tree partitions (ofpart) into a dedicated 'partitions' subnode;
this helps to disambiguate whether a node is a partition or some other
auxiliary data
* Improve error handling for partitioning failures
NAND
* General: Increase timeout period, for corner-case systems with
less-than-accurate jiffies
* Fix OF-based autoloading of several NAND drivers when built as modules
* pxa3xx_nand:
- Rework timing configuration to be more dynamic
- Refactor PM support
* brcmnand: prepare for NorthStar 2 support (ARM64, 16-bit NAND chips)
* sunxi_nand: refactoring and a few bug fixes
* vf610: new NAND driver
* FSMC: add SW BCH support; support common NAND DT bindings
* lpc32xx_slc: refactor and improve timing calculations logic
* denali: support for rev 5.1
SPI NOR
* Layering improvements
* Added Winbond lock/unlock support
* Added mtd_is_locked() (i.e., ioctl(MEMISLOCKED)) support
* Increase full-chip-erase timeout linearly with flash size
* fsl-quadspi: fix compile for non-ARM architectures
* New flash support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWPPj0AAoJEFySrpd9RFgtJEgP/RnfXRHBX51cUl4r8XrxiGtz
zlH5zFOCYWEOtlGjoD25wp+A5RRjWi62At6KmLJZncf0clJ65fyKHjt/JEg6YuI6
DUTMepTwyC2Wh7Ux1ZEH3KOnl64xh5p+Wf7Tl4yUr0DCd26VEwE9o7tPRlahv9nx
OhGCWS+uSsxW0Q2wDLCypFzXsnDBeoGxDO7VCIzle4d3aJ4PCcQIXINlr6ZYpocT
VTTadPCMsmYq6AgV5W3KYGYLj62ITiN2YxdJRacg+QkKLfl21u2wVy9Ahk/oj5TG
bV0DHiz6ky1F2K/bvJibcRFABiYup9UXIo1IzwLloSxEJ/GfennMC29xn9K/0gid
e2kO/Ajh/bihgJXzoAoZD/40YJK40X5VW9rQZgo482sMBGLmJOzZiOHOIEXaVohs
djQ7sbCwPmLwqp7C+6WTn8frp6ntIe9iXdmjDuR/WlPP0Sh5rI3cUeBQrJXEYxwc
aYt1Zxkst6gEMPQJ/S2TiKwWm0BxVWEUEjKmt9FPWOaQnwmoeju0Y/6jIvs1TQKM
vO8cmS17QyPUWT2kGIDmZ51KayY26uDC8/NA2t1HDYCiFbpDp61kgu2wyoBUTg7q
YIAvjtnwOaG9qk0SLfZu4FEgNi4a/bC1bxGxChsi+S2krpNQAeMlPY394cf6OdsE
j+CV/Ko0DguO26bO0MWr
=UzSW
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20151106' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"Core:
- WARN (in some cases) when a struct mtd_info is registered multiple
times; in the past this was "supported", but it's still error prone
for future development. There's only one ugly case of this left in
the tree (that we're aware of) and the owners are aware of the
problems there.
- fix potential deadlock in the blkdev removal path NOTE: the
(potential) deadlock was introduced in a for-stable patch. This
one is also marked for -stable.
- ioctl(BLKPG) compat_ioctl support; resolves issues with 32-bit user
space vs 64-bit kernel space
- Set MTD parent device correctly throughout the tree, so the tree
structure appears correctly in sysfs; many drivers were missing
this (soft) requirement
- Move device tree partitions (ofpart) into a dedicated 'partitions'
subnode; this helps to disambiguate whether a node is a partition
or some other auxiliary data
- Improve error handling for partitioning failures
NAND:
- General: Increase timeout period, for corner-case systems with
less-than-accurate jiffies
- Fix OF-based autoloading of several NAND drivers when built as
modules
- pxa3xx_nand:
- Rework timing configuration to be more dynamic
- Refactor PM support
- brcmnand: prepare for NorthStar 2 support (ARM64, 16-bit NAND
chips)
- sunxi_nand: refactoring and a few bug fixes
- vf610: new NAND driver
- FSMC: add SW BCH support; support common NAND DT bindings
- lpc32xx_slc: refactor and improve timing calculations logic
- denali: support for rev 5.1
SPI NOR:
- Layering improvements
- Added Winbond lock/unlock support
- Added mtd_is_locked() (i.e., ioctl(MEMISLOCKED)) support
- Increase full-chip-erase timeout linearly with flash size
- fsl-quadspi: fix compile for non-ARM architectures
- New flash support"
* tag 'for-linus-20151106' of git://git.infradead.org/linux-mtd: (169 commits)
mtd: don't WARN about overloaded users of mtd->reboot_notifier.notifier_call
mtd: nand: sunxi: avoid retrieving data before ECC pass
mtd: nand: sunxi: fix sunxi_nfc_hw_ecc_read/write_chunk()
mtd: blkdevs: fix potential deadlock + lockdep warnings
mtd: ofpart: move ofpart partitions to a dedicated dt node
doc: dt: mtd: support partitions in a special 'partitions' subnode
mtd: brcmnand: Force 8bit mode before doing nand_scan_ident()
mtd: brcmnand: factor out CFG and CFG_EXT bitfields
mtd: mtdpart: Do not fail mtd probe when parsing partitions fails
mtd: fsl-quadspi: fix macro collision problems with READ/WRITE
mtd: warn when registering the same master many times
mtd: fixup corner case error handling in mtd_device_parse_register()
mtd: tests: Replace timeval with ktime_t
mtd: fsmc_nand: Add BCH4 SW ECC support for SPEAr600
mtd: nand: vf610_nfc: use nand_check_erased_ecc_chunk() helper
mtd: nand: increase ready wait timeout and report timeouts
mtd: docg3: off by one in doc_register_sysfs()
mtd: pxa3xx_nand: clean up the pxa3xx timings
mtd: pxa3xx_nand: rework flash detection and timing setup
mtd: pxa3xx_nand: add helpers to setup the timings
...
|
|
|
Andrew F. Davis
|
3821a065f5 |
spi: Drop owner assignment from spi_drivers
An spi_driver does not need to set an owner, it will be populated by the driver core. Signed-off-by: Andrew F. Davis <afd@ti.com> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org> |
|
|
Dan Carpenter
|
2382960793 |
mtd: docg3: off by one in doc_register_sysfs()
Smatch found a bug in the error handling: drivers/mtd/devices/docg3.c:1634 doc_register_sysfs() error: buffer overflow 'doc_sys_attrs' 4 <= 4 The problem is that if the very last device_create_file() fails, then we are beyond the end of the array. Actually, any time i == 3 then there is a problem. We can fix this an simplify the code at the same time by moving the !ret conditions out of the for loops and using a goto instead. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Brian Norris <computersforpeace@gmail.com> |
|
|
Dongsheng Yang
|
ab84fce518 |
mtd: mtdram: check offs and len in mtdram->erase
We should prevent user to erasing mtd device with an unaligned offset or length. Signed-off-by: Dongsheng Yang <yangds.fnst@cn.fujitsu.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> |
|
|
Frans Klaver
|
90b997527e |
mtd: devices: sst251: show parent device in sysfs
Fix a bug where mtd parent device symlinks aren't shown in sysfs. While at it, make use of the default owner value set by mtdcore. Signed-off-by: Frans Klaver <fransklaver@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> |
|
|
Frans Klaver
|
7d24272253 |
mtd: devices: spear_smi: show parent device in sysfs
Fix a bug where mtd parent device symlinks aren't shown in sysfs. Signed-off-by: Frans Klaver <fransklaver@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> |
|
|
Frans Klaver
|
57eea0f5fb |
mtd: devices: mtd_dataflash: drop owner assignment
Owner is automatically set by mtdcore. Make use of that. Signed-off-by: Frans Klaver <fransklaver@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> |
|
|
Frans Klaver
|
1560d2132a |
mtd: devices: docg3: show parent device in sysfs
Fix a bug where mtd parent device symlinks aren't shown in sysfs. While at it, make use of the default owner value set by mtdcore. Signed-off-by: Frans Klaver <fransklaver@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> |
|
|
Frans Klaver
|
eb98198f23 |
mtd: devices: bcm47xxflash: show parent device in sysfs
Fix a bug where mtd parent device symlinks aren't shown in sysfs. While at it, make use of the default owner value set by mtdcore. Signed-off-by: Frans Klaver <fransklaver@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> |
|
|
Brian Norris
|
d489ff42db |
Revert "mtd: mtdram: check offs and len in mtdram->erase"
This reverts commit
|
|
|
Dongsheng Yang
|
7827e3acad |
mtd: mtdram: check offs and len in mtdram->erase
We should prevent user to erasing mtd device with an unaligned offset or length. Signed-off-by: Dongsheng Yang <yangds.fnst@cn.fujitsu.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> |
|
|
Brian Norris
|
db66e32e0d |
Linux 4.3-rc1
-----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQEcBAABAgAGBQJV9LbmAAoJEHm+PkMAQRiGb40IAJWcETZb6hoCUIrGZX+4Znqy UXYY9BwybF+3yPsTKWRUWQGifNhUiW7ejNgMO3QYG+E1RgJ6uj8Mym9I11+x3a9D beIem8Ftf1Zwt71zg6DpUCNhlRIfa3TTnbQMIYmoIihVwYWVve1/rMPD5kgafF6P Xnp7QSUh7uCK/G06sksK9aB2GkRgvoMKfAgTHmj094f24udl87NyUo8O8mP5QWX2 b0S5ZwlDRL64sio59QyxZK87f0TGnquDBLe6Gcl3wJQx/g3RzRpSxEkumylwx+S4 u9xeHlorOkg8a+k62TgbC6GP0Y6Ptk+yMF6UFCPsifwQTRvJubrA2ofdfPuggCk= =aqcb -----END PGP SIGNATURE----- Merge tag 'v4.3-rc1' into MTD -next development |
|
|
Jagan Teki
|
f9f3ce835d |
mtd: spi-nor: Zap unneeded write_enable from write_reg
The 'write_enable' argument is unused and unneeded, so remove it from the API. Signed-off-by: Jagan Teki <jteki@openedev.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Han Xu <han.xu@freescale.com> [Brian: fixed for nxp-spifi.c] Signed-off-by: Brian Norris <computersforpeace@gmail.com> |
|
|
Marek Vasut
|
11bff0b70c |
mtd: spi-nor: Decouple SPI NOR's device_node from controller device
The problem this patch is trying to address is such, that SPI NOR flash
devices attached to a dedicated SPI NOR controller cannot read their
properties from the associated struct device_node.
A couple of facts first:
1) Each SPI NOR flash has a struct spi_nor associated with it.
2) Each SPI NOR flash has certain device properties associated
with it, for example the OF property 'm25p,fast-read' is a
good pick. These properties are used by the SPI NOR core to
select which opcodes are sent to such SPI NOR flash. These
properties are coming from spi_nor .dev->of_node .
The problem is, that for SPI NOR controllers, the struct spi_nor .dev
element points to the struct device of the SPI NOR controller, not the
SPI NOR flash. Therefore, the associated dev->of_node also is the
one of the controller and therefore the SPI NOR core code is trying to
parse the SPI NOR controller's properties, not the properties of the
SPI NOR flash.
Note: The m25p80 driver is not affected, because the controller and
the flash are the same device, so the associated device_node
of the controller and the flash are the same.
This patch adjusts the SPI NOR core such that the device_node is not
picked from spi_nor .dev directly, but from a new separate spi_nor
.flash_node element. This let's the SPI NOR controller drivers set up
a different spi_nor .flash_node element for each SPI NOR flash.
This patch also fixes the controller drivers to be compatible with
this modification and correctly set the spi_nor .flash_node element.
This patch is inspired by
|
|
|
Linus Torvalds
|
12f03ee606 |
libnvdimm for 4.3:
1/ Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map. This facility is used by the pmem driver to
enable pfn_to_page() operations on the page frames returned by DAX
('direct_access' in 'struct block_device_operations'). For now, the
'memmap' allocation for these "device" pages comes from "System
RAM". Support for allocating the memmap from device memory will
arrive in a later kernel.
2/ Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3. Completion of
the conversion is targeted for v4.4.
3/ Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
4/ Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
5/ Miscellaneous updates and fixes to libnvdimm including support
for issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o57/
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"This update has successfully completed a 0day-kbuild run and has
appeared in a linux-next release. The changes outside of the typical
drivers/nvdimm/ and drivers/acpi/nfit.[ch] paths are related to the
removal of IORESOURCE_CACHEABLE, the introduction of memremap(), and
the introduction of ZONE_DEVICE + devm_memremap_pages().
Summary:
- Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map.
This facility is used by the pmem driver to enable pfn_to_page()
operations on the page frames returned by DAX ('direct_access' in
'struct block_device_operations').
For now, the 'memmap' allocation for these "device" pages comes
from "System RAM". Support for allocating the memmap from device
memory will arrive in a later kernel.
- Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3.
Completion of the conversion is targeted for v4.4.
- Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
- Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
- Miscellaneous updates and fixes to libnvdimm including support for
issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes"
* tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (34 commits)
libnvdimm, pmem: direct map legacy pmem by default
libnvdimm, pmem: 'struct page' for pmem
libnvdimm, pfn: 'struct page' provider infrastructure
x86, pmem: clarify that ARCH_HAS_PMEM_API implies PMEM mapped WB
add devm_memremap_pages
mm: ZONE_DEVICE for "device memory"
mm: move __phys_to_pfn and __pfn_to_phys to asm/generic/memory_model.h
dax: drop size parameter to ->direct_access()
nd_blk: change aperture mapping from WC to WB
nvdimm: change to use generic kvfree()
pmem, dax: have direct_access use __pmem annotation
dax: update I/O path to do proper PMEM flushing
pmem: add copy_from_iter_pmem() and clear_pmem()
pmem, x86: clean up conditional pmem includes
pmem: remove layer when calling arch_has_wmb_pmem()
pmem, x86: move x86 PMEM API to new pmem.h header
libnvdimm, e820: make CONFIG_X86_PMEM_LEGACY a tristate option
pmem: switch to devm_ allocations
devres: add devm_memremap
libnvdimm, btt: write and validate parent_uuid
...
|
|
|
Brian Norris
|
1976367173 |
mtd: spi-nor: embed struct mtd_info within struct spi_nor
This reflects the proper layering, so let's do it. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Tested-by: Joachim Eastwood <manabian@gmail.com> |
|
|
Brian Norris
|
c9ec3900ab |
mtd: spi-nor: assign mtd->priv in spi_nor_scan()
Layering suggests that the SPI NOR layer (not the hardware driver) should be initializing the MTD layer. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Tested-by: Joachim Eastwood <manabian@gmail.com> |
|
|
Javier Martinez Canillas
|
d1d97b76c4 |
mtd: dataflash: Export OF module alias information
The SPI core currently reports the MODALIAS uevent as "spi:<modalias>" even for SPI devices that were registered by OF. That means the OF module alias exported by MODULE_OF_TABLE(of,...) is currently not used and user-space has no way to autoload this module. But it is still a good practice to add the OF module alias information into the kernel module even when it currently is unused so once the SPI core is changed to report a correct OF modalias uevent, module autoloading will be working for this driver. Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> |
|
|
Dan Williams
|
2584cf8357 |
arch, drivers: don't include <asm/io.h> directly, use <linux/io.h> instead
Preparation for uniform definition of ioremap, ioremap_wc, ioremap_wt, and ioremap_cache, tree-wide. Acked-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com> |
|
|
Brian Norris
|
4316302292 |
mtd: m25p80: allow arbitrary OF matching for "jedec,spi-nor"
When we added the "jedec,spi-nor" compatible string for use in this
driver, we added it as a modalias option. The modalias can be derived in
different ways for platform devices vs. device tree (of_*) matching. But
for device tree matching (the primary target of this identifier string),
the modalias is determined from the first entry in the 'compatible'
property. IOW, the following properties would bind to this driver:
// Option (a), modalias = "spi-nor"
compatible = "jedec,spi-nor";
// Option (b), modalias = "spi-nor"
compatible = "idontknowwhatimdoing,spi-nor";
But the following would not:
// Option (c), modalias = "shinynewdevice"
compatible = "myvendor,shinynewdevice", "jedec,spi-nor";
So, we'd like to match (a) and (c) (even when we don't have an explicit
entry for "shinynewdevice"), and we'd rather not allow (b).
To do this, we
(1) always (for devices without specific platform data) pass the
modalias to the spi-nor library;
(2) rework the spi-nor library to not reject "bad" names, and
instead just fall back to autodetection; and
(3) add the .of_match_table to properly catch all "jedec,spi-nor".
This allows (a) and (c) without warnings, and rejects (b).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
|
Linus Torvalds
|
e4bc13adfd |
Merge branch 'for-4.2/writeback' of git://git.kernel.dk/linux-block
Pull cgroup writeback support from Jens Axboe:
"This is the big pull request for adding cgroup writeback support.
This code has been in development for a long time, and it has been
simmering in for-next for a good chunk of this cycle too. This is one
of those problems that has been talked about for at least half a
decade, finally there's a solution and code to go with it.
Also see last weeks writeup on LWN:
http://lwn.net/Articles/648292/"
* 'for-4.2/writeback' of git://git.kernel.dk/linux-block: (85 commits)
writeback, blkio: add documentation for cgroup writeback support
vfs, writeback: replace FS_CGROUP_WRITEBACK with SB_I_CGROUPWB
writeback: do foreign inode detection iff cgroup writeback is enabled
v9fs: fix error handling in v9fs_session_init()
bdi: fix wrong error return value in cgwb_create()
buffer: remove unusued 'ret' variable
writeback: disassociate inodes from dying bdi_writebacks
writeback: implement foreign cgroup inode bdi_writeback switching
writeback: add lockdep annotation to inode_to_wb()
writeback: use unlocked_inode_to_wb transaction in inode_congested()
writeback: implement unlocked_inode_to_wb transaction and use it for stat updates
writeback: implement [locked_]inode_to_wb_and_lock_list()
writeback: implement foreign cgroup inode detection
writeback: make writeback_control track the inode being written back
writeback: relocate wb[_try]_get(), wb_put(), inode_{attach|detach}_wb()
mm: vmscan: disable memcg direct reclaim stalling if cgroup writeback support is in use
writeback: implement memcg writeback domain based throttling
writeback: reset wb_domain->dirty_limit[_tstmp] when memcg domain size changes
writeback: implement memcg wb_domain
writeback: update wb_over_bg_thresh() to use wb_domain aware operations
...
|