The Aspeed AST2500 SoC contains a number of USB controllers:
* USB 1.1 Host Controller
* USB 2.0 Host Controller (x2)
* USB 2.0 Virtual Hub
* USB 2.0 Device Controller
* USB 1.1 HID Controller
The controllers are exposed via two USB ports with functionality muxed
as required. The following table illustrates the relationships between
the ports and the controllers via the mux function names:
Port | USB Version | USB Mode | Mux Function
------|--------------|--------------|-------------
A | 2.0 | Virtual Hub | USB2AD
A | 2.0 | Host | USB2AH
B | 1.1 | HID | USB11BHID
B | 2.0 | Device | USB2BD
B | 2.0 | Host | USB2BH
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AST2400 contains several USB controllers:
* USB 1.1 Host Controller
* USB 2.0 Host Controller
* USB 2.0 Virtual Hub
* USB 1.1 HID Controller
Pins for three ports are routed to the three controllers such that:
* Port 1 is a dedicated USB 1.1 host port
* Port 2 is shared between the USB 1.1 host and HID controllers
* Port 3 is shared between the USB 2.0 host and Hub controllers
As the pins for port 1 are fixed function there is no associated mux
function or group described in the bindings. Ports 2 and 3 are muxed as
above, and the table below describes the mapping between pinmux function
names and ports:
Port | USB Version | USB Mode | Mux Function
------|--------------|-----------|-------------
1 | 1.1 | Host | -
2 | 1.1 | Host | USB11H2
2 | 1.1 | HID | USB11D1
3 | 2.0 | Host | USB2H1
3 | 2.0 | Device | USB2D1
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch introducing the g5 pinctrl driver implemented a smattering of
pins to flesh out the implementation of the core and provide bare-bones
support for some OpenPOWER platforms and the AST2500 evaluation board.
Now, update the bindings document to reflect the complete functionality
and implement the necessary pin configuration tables in the driver.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch introducing the g4 pinctrl driver implemented a smattering of
pins to flesh out the implementation of the core and provide bare-bones
support for some OpenPOWER platforms. Now, update the bindings document
to reflect the complete functionality and implement the necessary pin
configuration tables in the driver.
Cc: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The System Control Unit IP block in the Aspeed SoCs is typically where
the pinmux configuration is found, but not always. A number of pins
depend on state in one of LPC Host Control (LHC) or SoC Display
Controller (GFX) IP blocks, so the Aspeed pinmux drivers should have the
means to adjust these as necessary.
We use syscon to cast a regmap over the GFX and LPC blocks, which is
used as an arbitration layer between the relevant driver and the pinctrl
subsystem. The regmaps are then exposed to the SoC-specific pinctrl
drivers by phandles in the devicetree, and are selected during a mux
request by querying a new 'ip' member in struct aspeed_sig_desc.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reference the SoC-specific compatible string in the examples as
required.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPI1 function was associated with the wrong pins: The functions that
those pins provide is either an SPI debug or passthrough function
coupled to SPI1. Make the SPI1 mux function configure the relevant pins
and associate new SPI1DEBUG and SPI1PASSTHRU functions with the pins
that were already defined.
The notation used in the datasheet's multi-function pin table for the SoC is
often creative: in this case the SYS* signals are enabled by a single bit,
which is nothing unusual on its own, but in this case the bit was also
participating in a multi-bit bitfield and therefore represented multiple
functions. This fact was overlooked in the original patch.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Outline expectations on the pin controller's relationship with the
System Control Unit (SCU) IP through syscon, and document the compatible
strings for 4th and 5th generation Aspeed SoC pin controllers.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Andrew Jeffery