Remove BE prepare ops which enables MCLK by default. If MCLK is required
to be enabled for any specific platform, it needs to be enabled in the
corresponding machine driver.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If D3 IPC fails or times out, firmware needs to be reloaded as driver
continues the reset.
So set the fw_load flag to false to reload the firmware in D0.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In system suspend, firmware needs to be re-downloaded as IMR is cleared.
When firmware is downloaded in D0, core state is not set to running
state causing instability with subsequent D0-D3 cycles.
So set the core state correctly during D0 and check the DSP core state
if not in reset to set the DSP to D3.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When DSP is in D3, no interrupts are expected, so disable
interrupt while entering D3.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the widget is a mixin module, just unbind between source and sink
and don't stop the source pipe as there can be multiple sinks
connected.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP pipe needs to stopped before deleting the pipe. Currently check is
for pipe state > STARTED, which is incorrect. So changed to include
pipe state STARTED to stop the pipe if it started.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure this machine driver is only used if enabled explicitly
and if there is no information found in the SSDT.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add card with dummy codec and DAI to make I2S signals observable.
Uses Mic and Speaker pins/widgets to control DAPM
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add entries in HID table and reference to bytcht_da7213 driver
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add new machine driver, tested with Ard-Audio-DA7212 [1]
connected to MinnowBoardMAX Turbot.
The MCLK is managed by the codec driver using the "mclk" handle
to reuse existing code, but it could just as well be handled
by this machine driver.
[1] http://www.dialog-semiconductor.com/content/ard-audio-da7212
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a commit 4cd9899f0d ("ASoC: Intel: Skylake: Add multiple pin
formats") describes, 'fixups is applied to pin 0 only'. On the other
hand, the commit left some codes as what they were. This might
confuses readers.
This commit fixes the issue. This doesn't change driver behaviour at all.
Fixes: 4cd9899f0d ("ASoC: Intel: Skylake: Add multiple pin formats")
Signed-off-by: Takashi Sakamoto <takashi.sakamoto@miraclelinux.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In 'include/linux/kernel.h', there's a helper macro to round numerical
value. Let's use it.
Signed-off-by: Takashi Sakamoto <takashi.sakamoto@miraclelinux.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During S3->S0 transition, sometime ROM init fails because of
authentication engine loads later than the OS. In this case driver
waits for a longer period and then retries the FW download causing
huge delay in resume time of audio device.
To avoid this, ROM INIT wait time is set to a optimal value and
increased the retries for firmware download.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Store the DSP firmware/library at boot, so that for S3 to S0 transition
use the stored ctx for downloading the firmware to DSP memory.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since index is always 0 replace devm_gpiod_get_index() by devm_gpiod_get()
and apply proper flags.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trivial fix to spelling mistake in dev_err message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.
Use BUILD_BUG_ON in a couple ATM drivers.
In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement. Hopefully this patch inspires
someone else to trim vsprintf.c more.
Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
followings||following
While we are here, add a missing colon in the boilerplate in DT binding
documents. The "you SoC" in allwinner,sunxi-pinctrl.txt was fixed as
well.
I reworded "as the followings:" to "as follows:" for
drivers/usb/gadget/udc/renesas_usb3.c.
Link: http://lkml.kernel.org/r/1481573103-11329-32-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
deintializing||deinitializing
deintialize||deinitialize
deintialized||deinitialized
Link: http://lkml.kernel.org/r/1481573103-11329-28-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
intialization||initialization
The "inintialization" in drivers/acpi/spcr.c is a different pattern but
I fixed it as well in this commit.
Link: http://lkml.kernel.org/r/1481573103-11329-16-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
unneded||unneeded
Link: http://lkml.kernel.org/r/1481573103-11329-15-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's not necessary to unregister a component registered
with devm_snd_soc_register_component(). Also removed
pointness clk_disable_unprepare() from error path and
snd_soc_unregister_platform() from the remove.
Fixes: f8260afa44 ("ASoC: sunxi: Add support for the SPDIF block")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the pcm jack is created, create and initialize the pin switch
widget for each port. Pin switch is to enable/disable the pin when
monitor is connected/disconnected.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
configurable LRC and BCLK divide. The driver
will make configurations of LRC and BCLK automatically according to
BCLK and FS information in master mode.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake is new Intel SoC, so add codec entry for HDMI
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake is next gen SoC, so add the IDs for Geminilake.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake reference platform also uses combo jack for audio connector
so we need to set codec pdata to use this based on DMI match for this
board.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake has two different devices connected to the same SSP, so use
device_type check to get correct device configuration.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the pcm jack is created, create and initialize the pin switch
widget for each port. Pin switch is to enable/disable the pin when
monitor is connected/disconnected.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the pcm jack is created, create and initialize the pin switch
widget for each port. Pin switch is to enable/disable the pin when
monitor is connected/disconnected.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the pcm jack is created, create and initialize the pin switch
widget for each port. Pin switch is to enable/disable the pin when
monitor is connected/disconnected.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jeeja KP