There are several arch-specific RTC drivers that can be successfully
compiled on other platforms. Add a COMPILE_TEST dependency for those.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Maxim Semiconductor's PMIC MAX77686 has RTC IP which is
reused in the MAX77620/MAX20024 PMICs.
Add support for these devices in MAX77686 RTC driver. This
device does not have RTC alarm pending status outside of
RTC IP. The RTC IP is having separate I2C address for its
register access.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Kconfig option for rv3029 is not mentioning any part number, explicitly
show rv3029.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RTC entries are mostly grouped by vendor. Move the few outliers in
place.
Also, change the one occurrence of 'nxp' to 'NXP' to make all NXP
entries consistent.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This driver adds support for the PIC32 real time clock and calendar
peripheral:
- reading and setting time
- alarms provided by dedicated IRQ
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add support for RTC controller found on Alphascale asm9260
SoC.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
At the moment the "sun6i" RTC drivers depends on having two specific
SoC families selected.
The Allwinner A64 SoC has the same RTC, so extend the Kconfig option
to allow inclusion of the driver for all Allwinner SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RX6110 comes in two different variants: SPI and I2C.
This driver only supports the SPI variant.
If the need ever arises to also support the I2C variant, this driver
could easily be refactored to support both cases.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
DS3231 has the temperature registers with a resolution of 0.25
degree celsius. This enables to get the value through hwmon.
# cat /sys/class/i2c-adapter/i2c-2/2-0068/hwmon/hwmon0/temp1_input
21000
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The mt6397 RTC driver can be built either when the MFD_MT6397 driver
is enabled (which selects IRQ_DOMAIN), or when compile testing.
The latter however fails without IRQ domains:
drivers/rtc/rtc-mt6397.c: In function 'mtk_rtc_probe':
drivers/rtc/rtc-mt6397.c:326:13: error: implicit declaration of function 'irq_create_mapping' [-Werror=implicit-function-declaration]
rtc->irq = irq_create_mapping(mt6397_chip->irq_domain, res->start);
This adds an explicit dependency for the COMPILE_TEST case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The max77686 RTC driver now supports the max77802 RTC as
well so there's no need to have a separate driver anymore.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This driver supports the following functions:
- reading and setting time
- alarms when connected to an IRQ
- reading and clearing the voltage low flags
Datasheet:
http://www.epsondevice.com/docs/qd/en/DownloadServlet?id=ID000956
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This driver supports the following functions:
- reading and settings time
- alarms when connected to an IRQ
- reading and clearing the voltage low flags
- nvram
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Introduce a device tree binding for specifying the trickle charger
configuration for ds1390.
Signed-off-by: Ivan Grimaldi <grimaldi.ivan@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add support for RTC controller found on Xilinx Zynq Ultrascale+ MPSoC
platform.
Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Currently, the rtc-sa1100 and rtc-pxa drivers co-exist as rtc-pxa has a
superset of functionality. Having 2 drivers sharing the same memory
resource is not allowed by the driver model if resources are properly
declared. This problem was avoided by not adding memory resources to the
SA1100 RTC driver, but that prevents clean-up of the SA1100 driver.
This commit converts the PXA RTC to use the exported SA1100 RTC
functions. Now the sa1100-rtc and pxa-rtc devices are mutually
exclusive, so we must remove the sa1100-rtc from pxa27x and pxa3xx.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: rtc-linux@googlegroups.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add DA9062 RTC support into the existing DA9063 RTC driver component by
using generic access tables for common register and bit mask definitions.
The following change will add generic register and bit mask support to the
DA9063 RTC. The changes are slightly complicated by requiring support for
three register sets: DA9063-AD, DA9063-BB and DA9062-AA.
The following alterations have been made to the DA9063 RTC:
- Addition of a da9063_compatible_rtc_regmap structure to hold all generic
registers and bitmasks for this type of RTC component.
- A re-write of struct da9063 to use pointers for regmap and compatible
registers/masks definitions
- Addition of a of_device_id table for DA9063 and DA9062 defaults
- Refactoring functions to use struct da9063_compatible_rtc accesses to
generic registers/masks instead of using defines from registers.h
- Re-work of da9063_rtc_probe() to use of_match_node() and dev_get_regmap()
to provide initialisation of generic registers and masks and access to
regmap
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add driver for the RTC found on NXP LPC178x/18xx/408x/43xx devices.
The RTC provides calendar and clock functionality together with
alarm interrupt support.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Select REGMAP_MMIO to fix the following build error seen with x86_64
randconfig.
drivers/built-in.o: In function `snvs_rtc_probe':
rtc-snvs.c:(.text+0x567730): undefined reference to `devm_regmap_init_mmio_clk'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
Multiple options depend on I2C but are already under under if I2C. Remove
those useless dependencies.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Some entries in the Kconfig are improperly indented with spaces instead of
tabs.
Also fix whitespaces in Makefile.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Currently, CONFIG_RTC_SYSTOHC uses CONFIG_RTC_HCTOSYS_DEVICE which
is originally used by CONFIG_RTC_HCTOSYS, but this rtc device has
some limiations, for example, it must be battery-backed, be able
to work with irq off and through system suspension, etc.
So add CONFIG_RTC_SYSTOHC_DEVICE used exclusively for CONFIG_RTC_SYSTOHC,
it is more lenient compared to CONFIG_RTC_HCTOSYS_DEVICE, and could
be assigned any available RTC in the system.
Default value is CONFIG_RTC_HCTOSYS_DEVICE which is "rtc0" by default.
After this patch, NTP will sync up "rtc0" by default.
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Driver for the on chip RTC found on Cortina's SoC Gemini.
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
[alexandre.belloni@free-electrons.com: use devm_request_irq() and remove
useless goto]
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Currently, code of Loongson-2/3 is under loongson directory and code of
Loongson-1 is under loongson1 directory. Besides, there are Kconfig
options such as MACH_LOONGSON and MACH_LOONGSON1. This naming style is
very ugly and confusing. Since Loongson-2/3 are both 64-bit general-
purpose CPU while Loongson-1 is 32-bit SoC, we rename both file names
and Kconfig symbols from loongson/loongson1 to loongson64/loongson32.
[ralf@linux-mips.org: Resolve a number of simple conflicts.]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Kelvin Cheung <keguang.zhang@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/9790/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is a basic driver for the ultra-low-power Abracon AB x80x series of RTC
chips. It supports in particular, the supersets AB0805 and AB1805.
It allows reading and writing the time, and enables the supercapacitor/
battery charger.
[arnd@arndb.de: abx805 depends on i2c]
[alexandre.belloni@free-electrons.com: renam buffer from date to buf in abx80x_rtc_read_time()]
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ST's Low Power Controller (LPC) controls two devices; watchdog and RTC.
Only one of the devices can be used at any one time. This is enforced
by the correlating MFD driver. This portion of the driver-set controls
the Real Time Clock.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
RTC is present in AM43xx and DRA7xx also. Updating the Kconfig to depend
on ARCH_OMAP or ARCH_DAVINCI
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add driver for the RTC hardware block on the Conexant CX92755 SoC, from
the Digicolor series of SoCs. Tested on the Equinox evaluation board for
the CX92755 chip.
[akpm@linux-foundation.org: build command arrays at compile-time]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
This is a good healthy set of various code removals. Total net delta is 8100
lines removed.
Among the larger cleanups are:
- Removal of old Samsung S3C DMA infrastructure by Arnd
- Removal of the non-DT version of the 'lager' board by Magnus Damm
- General stale code removal on OMAP and Davinci by Rickard Strandqvist
- Removal of non-DT support on am3517 platforms by Tony Lindgren
... plus several other cleanups of various platforms across the board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tsjK
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is a good healthy set of various code removals. Total net delta
is 8100 lines removed.
Among the larger cleanups are:
- Removal of old Samsung S3C DMA infrastructure by Arnd
- Removal of the non-DT version of the 'lager' board by Magnus Damm
- General stale code removal on OMAP and Davinci by Rickard Strandqvist
- Removal of non-DT support on am3517 platforms by Tony Lindgren
... plus several other cleanups of various platforms across the board"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (47 commits)
ARM: sirf: drop redundant function and marco declaration
arm: omap: specify PMUs are for ARMv7 CPUs
arm: shmobile: specify PMUs are for ARMv7 CPUs
arm: iop: specify PMUs are for XScale CPUs
arm: pxa: specify PMUs are for XScale CPUs
arm: realview: specify PMU types
ARM: SAMSUNG: remove unused DMA infrastructure
ARM: OMAP3: Add back Kconfig option MACH_OMAP3517EVM for ASoC
ARM: davinci: Remove CDCE949 driver
ARM: at91: remove useless at91rm9200_set_type()
ARM: at91: remove useless at91rm9200_dt_initialize()
ARM: at91: move debug-macro.S into the common space
ARM: at91: remove useless at91_sysirq_mask_rtx
ARM: at91: remove useless config MACH_AT91SAM9_DT
ARM: at91: remove useless config MACH_AT91RM9200_DT
ARM: at91: remove unused mach/memory.h
ARM: at91: remove useless header file includes
ARM: at91: remove unneeded header file
rtc: at91/Kconfig: remove useless options
ARM: at91/Documentation: add a README for Atmel SoCs
...
This adds a driver for the Dallas/Maxim DS1685-family of RTC chips. It
supports the DS1685/DS1687, DS1688/DS1691, DS1689/DS1693, DS17285/DS17287,
DS17485/DS17487, and DS17885/DS17887 RTC chips. These chips are commonly
found in SGI O2 and SGI Octane systems. It was originally derived from a
driver patch submitted by Matthias Fuchs many years ago for use in
EPPC-405-UC modules, which also used these RTCs. In addition to the
time-keeping functions, this RTC also handles the shutdown mechanism of
the O2 and Octane and acts as a partial NVRAM for the boot PROMS in these
systems.
Verified on both an SGI O2 and an SGI Octane.
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new mvebu SoCs come with a new RTC driver. This patch adds the
support for this new IP which is currently found in the Armada 38x
SoCs.
This RTC provides two alarms, but only the first one is used in the
driver. The RTC also allows using periodic interrupts.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Boris BREZILLON <boris.brezillon@free-electrons.com>
Cc: Lior Amsalem <alior@marvell.com>
Cc: Tawfik Bayouk <tawfik@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for Abracon AB-RTCMC-32.768kHz-B5ZE-S3
RTC/Calendar module w/ I2C interface.
This support includes RTC time reading and setting, Alarm (1 minute
accuracy) reading and setting, and battery low detection. The device also
supports frequency adjustment and two timers but those features are
currently not implemented in this driver. Due to alarm accuracy
limitation (and current lack of timer support in the driver), UIE mode is
not supported.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robherring2@gmail.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Landley <rob@landley.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As we removed all the !DT boards during 3.19 cycle, we can now remove these
options.
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Support for keyword 'boolean' will be dropped later on.
No functional change.
Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Some nice cleanups like removing bootmem, and removal of __get_cpu_var().
There is one patch to mm/gup.c. This is the generic GUP implementation, but is
only used by us and arm(64). We have an ack from Steve Capper, and although we
didn't get an ack from Andrew he told us to take the patch through the powerpc
tree.
There's one cxl patch. This is in drivers/misc, but Greg said he was happy for
us to manage fixes for it.
There is an infrastructure patch to support an IPMI driver for OPAL. That patch
also appears in Corey Minyard's IPMI tree, you may see a conflict there.
There is also an RTC driver for OPAL. We weren't able to get any response from
the RTC maintainer, Alessandro Zummo, so in the end we just merged the driver.
The usual batch of Freescale updates from Scott.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jvyT
-----END PGP SIGNATURE-----
Merge tag 'powerpc-3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
"Some nice cleanups like removing bootmem, and removal of
__get_cpu_var().
There is one patch to mm/gup.c. This is the generic GUP
implementation, but is only used by us and arm(64). We have an ack
from Steve Capper, and although we didn't get an ack from Andrew he
told us to take the patch through the powerpc tree.
There's one cxl patch. This is in drivers/misc, but Greg said he was
happy for us to manage fixes for it.
There is an infrastructure patch to support an IPMI driver for OPAL.
There is also an RTC driver for OPAL. We weren't able to get any
response from the RTC maintainer, Alessandro Zummo, so in the end we
just merged the driver.
The usual batch of Freescale updates from Scott"
* tag 'powerpc-3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (101 commits)
powerpc/powernv: Return to cpu offline loop when finished in KVM guest
powerpc/book3s: Fix partial invalidation of TLBs in MCE code.
powerpc/mm: don't do tlbie for updatepp request with NO HPTE fault
powerpc/xmon: Cleanup the breakpoint flags
powerpc/xmon: Enable HW instruction breakpoint on POWER8
powerpc/mm/thp: Use tlbiel if possible
powerpc/mm/thp: Remove code duplication
powerpc/mm/hugetlb: Sanity check gigantic hugepage count
powerpc/oprofile: Disable pagefaults during user stack read
powerpc/mm: Check for matching hpte without taking hpte lock
powerpc: Drop useless warning in eeh_init()
powerpc/powernv: Cleanup unused MCE definitions/declarations.
powerpc/eeh: Dump PHB diag-data early
powerpc/eeh: Recover EEH error on ownership change for BCM5719
powerpc/eeh: Set EEH_PE_RESET on PE reset
powerpc/eeh: Refactor eeh_reset_pe()
powerpc: Remove more traces of bootmem
powerpc/pseries: Initialise nvram_pstore_info's buf_lock
cxl: Name interrupts in /proc/interrupt
cxl: Return error to PSL if IRQ demultiplexing fails & print clearer warning
...
Add support for the watchdog functionality of the DS1374 rtc. Based on
the m41t80 watchdog functionality Note: watchdog uses the same registers
as alarm.
[akpm@linux-foundation.org: don't forget mutex_unlock() in ds1374_wdt_open() error path]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Soeren Andersen <san@rosetechnology.dk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The at91 cleanups changed a lot of files, this merges in the
latest cleanups to resolve the conflicts
Conflicts:
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/clock.c
arch/arm/mach-at91/clock.h
drivers/rtc/Kconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The precise selection is useless, so we simply remove these dependencies.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
This resolves some of the obvious conflicts between the at91 cleanup and
drivers branches.
Conflicts:
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-at91/at91sam9rl.c
drivers/rtc/Kconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It is only about a not so recent driver for old platforms: RTT as RTC driver:
- RTT as RTC driver enhancements and machine specific include files removal
- RTT as RTC driver conversion to device tree
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUZg/EAAoJEAf03oE53VmQ/KAIAJi5Ky2ekaZ4FGWbDrnQBHV+
X0M/wvCdHw4D7VENo1W3U3ulf5r0XimeY6nnbmx3Ki0fTE2O3VyfLNzkjQtMf6iX
TfoJM9y4fWsY5AXnynYO1Gj/2CH6Xab79Kb5sxL8b9VvlUMxlsKoQOmUYHC775OX
YiBfp3dZYODkMyIIQmSkoZGj+kkgWbjMrp9CPueqVltha/EbfBP96Kib2G/aJVkb
F9QyOq8B/mpUk2P29L1hc9X0/tjwaLZsO97zzhYVj7VwZS9sbYztQgmUNdtEds4/
7EhMwSXxb9L5LkuoyuHFpRLMGzLrN9XBftE58s92hXwnM2KZE4eNo/JF0SGDOKo=
=POJG
-----END PGP SIGNATURE-----
Merge tag 'at91-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/drivers
Pull "First batch of drivers for 3.19" from Nicolas Ferre:
It is only about a not so recent driver for old platforms: RTT as RTC driver:
- RTT as RTC driver enhancements and machine specific include files removal
- RTT as RTC driver conversion to device tree
* tag 'at91-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
rtc: at91sam9: add DT bindings documentation
rtc: at91sam9: use clk API instead of relying on AT91_SLOW_CLOCK
ARM: at91: add clk_lookup entry for RTT devices
rtc: at91sam9: rework the Kconfig description
rtc: at91sam9: make use of syscon/regmap to access GPBR registers
rtc: at91sam9: add DT support
rtc: at91sam9: replace devm_ioremap by devm_ioremap_resource
rtc: at91sam9: use standard readl/writel functions instead of raw versions
rtc: at91sam9: remove references to mach specific headers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When removing old board !DT support, several Kconfig options were deleted.
Propagate this removal to drivers Kconfig files.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Alexandre Belloni