mirror of https://gitee.com/openkylin/linux.git
90 Commits
| Author | SHA1 | Message | Date |
|---|---|---|---|
Douglas Anderson
|
cf9d052aa6 |
pinctrl: qcom: Don't clear pending interrupts when enabling
In Linux, if a driver does disable_irq() and later does enable_irq() on its interrupt, I believe it's expecting these properties: * If an interrupt was pending when the driver disabled then it will still be pending after the driver re-enables. * If an edge-triggered interrupt comes in while an interrupt is disabled it should assert when the interrupt is re-enabled. If you think that the above sounds a lot like the disable_irq() and enable_irq() are supposed to be masking/unmasking the interrupt instead of disabling/enabling it then you've made an astute observation. Specifically when talking about interrupts, "mask" usually means to stop posting interrupts but keep tracking them and "disable" means to fully shut off interrupt detection. It's unfortunate that this is so confusing, but presumably this is all the way it is for historical reasons. Perhaps more confusing than the above is that, even though clients of IRQs themselves don't have a way to request mask/unmask vs. disable/enable calls, IRQ chips themselves can implement both. ...and yet more confusing is that if an IRQ chip implements disable/enable then they will be called when a client driver calls disable_irq() / enable_irq(). It does feel like some of the above could be cleared up. However, without any other core interrupt changes it should be clear that when an IRQ chip gets a request to "disable" an IRQ that it has to treat it like a mask of that IRQ. In any case, after that long interlude you can see that the "unmask and clear" can break things. Maulik tried to fix it so that we no longer did "unmask and clear" in commit |
|
|
Douglas Anderson
|
a95881d6aa |
pinctrl: qcom: Properly clear "intr_ack_high" interrupts when unmasking
In commit |
|
|
Douglas Anderson
|
4079d35fa4 |
pinctrl: qcom: No need to read-modify-write the interrupt status
When the Qualcomm pinctrl driver wants to Ack an interrupt, it does a read-modify-write on the interrupt status register. On some SoCs it makes sure that the status bit is 1 to "Ack" and on others it makes sure that the bit is 0 to "Ack". Presumably the first type of interrupt controller is a "write 1 to clear" type register and the second just let you directly set the interrupt status register. As far as I can tell from scanning structure definitions, the interrupt status bit is always in a register by itself. Thus with both types of interrupt controllers it is safe to "Ack" interrupts without doing a read-modify-write. We can do a simple write. It should be noted that if the interrupt status bit _was_ ever in a register with other things (like maybe status bits for other GPIOs): a) For "write 1 clear" type controllers then read-modify-write would be totally wrong because we'd accidentally end up clearing interrupts we weren't looking at. b) For "direct set" type controllers then read-modify-write would also be wrong because someone setting one of the other bits in the register might accidentally clear (or set) our interrupt. I say this simply to show that the current read-modify-write doesn't provide any sort of "future proofing" of the code. In fact (for "write 1 clear" controllers) the new code is slightly more "future proof" since it would allow more than one interrupt status bits to share a register. NOTE: this code fixes no bugs--it simply avoids an extra register read. Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Maulik Shah <mkshah@codeaurora.org> Tested-by: Maulik Shah <mkshah@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20210114191601.v7.2.I3635de080604e1feda770591c5563bd6e63dd39d@changeid Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Douglas Anderson
|
a82e537807 |
pinctrl: qcom: Allow SoCs to specify a GPIO function that's not 0
There's currently a comment in the code saying function 0 is GPIO. Instead of hardcoding it, let's add a member where an SoC can specify it. No known SoCs use a number other than 0, but this just makes the code clearer. NOTE: no SoC code needs to be updated since we can rely on zero-initialization. Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Maulik Shah <mkshah@codeaurora.org> Tested-by: Maulik Shah <mkshah@codeaurora.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20210114191601.v7.1.I3ad184e3423d8e479bc3e86f5b393abb1704a1d1@changeid Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Linus Torvalds
|
f68e4041ef |
This is the bulk of pin control changes for the v5.11 kernel:
New drivers:
- New driver for the Microchip Serial GPIO "SGPIO".
- Qualcomm SM8250 LPASS (Low Power Audio Subsystem) GPIO driver.
New subdrivers:
- Intel Lakefield subdriver.
- Intel Elkhart Lake subdriver.
- Intel Alder Lake-S subdriver.
- Qualcomm MSM8953 subdriver.
- Qualcomm SDX55 subdriver.
- Qualcomm SDX55 PMIC subdriver.
- Ocelot Luton SoC subdriver.
- Ocelot Serval SoC subdriver.
Modularization:
- The Meson driver can now be built as modules.
- The Qualcomm driver(s) can now be built as modules.
Incremental improvements:
- The Intel driver now supports pin configuration for GPIO-related
configurations.
- A bunch of Renesas PFC drivers have been augmented with support
for QSPI pins, groups and functions.
- Non-critical fixes to the irq handling in the Allwinner Sunxi
driver.
-----BEGIN PGP SIGNATURE-----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=e5sV
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.11 kernel.
Drivers, drivers and drivers. Not a single core change.
Some new stuff, especially a bunch of new Intel, Qualcomm and Ocelot
SoCs.
As part of the modularization attempt, I applied one patch affecting
the firmware subsystem as a functional (not syntactic/semantic)
dependency and then it blew up in our face, so I had to revert it,
bummer. It will come in later, through that subsystem, I guess.
New drivers:
- New driver for the Microchip Serial GPIO "SGPIO".
- Qualcomm SM8250 LPASS (Low Power Audio Subsystem) GPIO driver.
New subdrivers:
- Intel Lakefield subdriver.
- Intel Elkhart Lake subdriver.
- Intel Alder Lake-S subdriver.
- Qualcomm MSM8953 subdriver.
- Qualcomm SDX55 subdriver.
- Qualcomm SDX55 PMIC subdriver.
- Ocelot Luton SoC subdriver.
- Ocelot Serval SoC subdriver.
Modularization:
- The Meson driver can now be built as modules.
- The Qualcomm driver(s) can now be built as modules.
Incremental improvements:
- The Intel driver now supports pin configuration for GPIO-related
configurations.
- A bunch of Renesas PFC drivers have been augmented with support for
QSPI pins, groups and functions.
- Non-critical fixes to the irq handling in the Allwinner Sunxi
driver"
* tag 'pinctrl-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (80 commits)
pinctrl/spear: simplify the return expression of spear300_pinctrl_probe()
pinctrl: mediatek: simplify the return expression of mtk_pinconf_bias_disable_set_rev1()
dt-bindings: pinctrl: pinctrl-microchip-sgpio: Add irq support
pinctrl: pinctrl-microchip-sgpio: Add irq support (for sparx5)
pinctrl: qcom: Add sm8250 lpass lpi pinctrl driver
dt-bindings: pinctrl: qcom: Add sm8250 lpass lpi pinctrl bindings
pinctrl: qcom-pmic-gpio: Add support for pmx55
dt-bindings: pinctrl: qcom-pmic-gpio: Add pmx55 support
pinctrl: pinctrl-microchip-sgpio: Mark some symbols with static keyword
pinctrl: at91-pio4: Make PINCTRL_AT91PIO4 depend on HAS_IOMEM to fix build error
pinctrl: mtk: Fix low level output voltage issue
pinctrl: falcon: add missing put_device() call in pinctrl_falcon_probe()
pinctrl: actions: pinctrl-s500: Constify s500_padinfo[]
pinctrl: pinctrl-microchip-sgpio: Add OF config dependency
pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO
dt-bindings: pinctrl: Add bindings for pinctrl-microchip-sgpio driver
pinctrl: at91-pio4: add support for fewer lines on last PIO bank
pinctrl: sunxi: Always call chained_irq_{enter, exit} in sunxi_pinctrl_irq_handler
pinctrl: sunxi: Mark the irq bank not found in sunxi_pinctrl_irq_handler() with WARN_ON
pinctrl: sunxi: fix irq bank map for the Allwinner A100 pin controller
...
|
|
|
John Stultz
|
38e86f5c26 |
pinctrl: qcom: Allow pinctrl-msm code to be loadable as a module
Tweaks to allow pinctrl-msm code to be loadable as a module. This is needed in order to support having the qcom-scm driver, which pinctrl-msm calls into, configured as a module. This requires that we tweak Kconfigs selecting PINCTRL_MSM to also depend on QCOM_SCM || QCOM_SCM=n so that we match the module setting of QCOM_SCM. Signed-off-by: John Stultz <john.stultz@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will@kernel.org> Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Joerg Roedel <joro@8bytes.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <maz@kernel.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Vinod Koul <vkoul@kernel.org> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Maulik Shah <mkshah@codeaurora.org> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Saravana Kannan <saravanak@google.com> Cc: Todd Kjos <tkjos@google.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: linux-arm-msm@vger.kernel.org Cc: iommu@lists.linux-foundation.org Cc: linux-gpio@vger.kernel.org Link: https://lore.kernel.org/r/20201106042710.55979-2-john.stultz@linaro.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Maulik Shah
|
71266d9d39 |
pinctrl: qcom: Move clearing pending IRQ to .irq_request_resources callback
When GPIOs that are routed to PDC are used as output they can still latch
the IRQ pending at GIC. As a result the spurious IRQ was handled when the
client driver change the direction to input to starts using it as IRQ.
Currently such erroneous latched IRQ are cleared with .irq_enable callback
however if the driver continue to use GPIO as interrupt and invokes
disable_irq() followed by enable_irq() then everytime during enable_irq()
previously latched interrupt gets cleared.
This can make edge IRQs not seen after enable_irq() if they had arrived
after the driver has invoked disable_irq() and were pending at GIC.
Move clearing erroneous IRQ to .irq_request_resources callback as this is
the place where GPIO direction is changed as input and its locked as IRQ.
While at this add a missing check to invoke msm_gpio_irq_clear_unmask()
from .irq_enable callback only when GPIO is not routed to PDC.
Fixes:
|
|
|
Maulik Shah
|
dd87bd0982 |
pinctrl: qcom: Set IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag
Set IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag to enable/unmask the wakeirqs during suspend entry. Signed-off-by: Maulik Shah <mkshah@codeaurora.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Tested-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/1601267524-20199-5-git-send-email-mkshah@codeaurora.org |
|
|
Maulik Shah
|
f41aaca593 |
pinctrl: qcom: Use return value from irq_set_wake() call
msmgpio irqchip was not using return value of irq_set_irq_wake() callback since previously GIC-v3 irqchip neither had IRQCHIP_SKIP_SET_WAKE flag nor it implemented .irq_set_wake callback. This lead to irq_set_irq_wake() return error -ENXIO. However from 'commit |
|
|
Maulik Shah
|
c5f72aeb65 |
pinctrl: qcom: Set IRQCHIP_SET_TYPE_MASKED and IRQCHIP_MASK_ON_SUSPEND flags
Both IRQCHIP_SET_TYPE_MASKED and IRQCHIP_MASK_ON_SUSPEND flags are already
set for msmgpio's parent PDC irqchip but GPIO interrupts do not get masked
during suspend or during setting irq type since genirq checks irqchip flag
of msmgpio irqchip which forwards these calls to its parent PDC irqchip.
Add irqchip specific flags for msmgpio irqchip to mask non wakeirqs during
suspend and mask before setting irq type. Masking before changing type make
sures any spurious interrupt is not detected during this operation.
Fixes:
|
|
|
Linus Torvalds
|
9420f1ce01 |
This is the bulk of the pin control changes for the v5.9
kernel series:
Core changes:
- The GPIO patch "gpiolib: Introduce
for_each_requested_gpio_in_range() macro" was put in an
immutable branch and merged into the pinctrl tree as well.
We see these changes also here.
- Improved debug output for pins used as GPIO.
New drivers:
- Ocelot Sparx5 SoC driver.
- Intel Emmitsburg SoC subdriver.
- Intel Tiger Lake-H SoC subdriver.
- Qualcomm PM660 SoC subdriver.
- Renesas SH-PFC R8A774E1 subdriver.
Driver improvements:
- Linear improvement and cleanups of the Intel drivers for
Cherryview, Lynxpoint, Baytrail etc. Improved locking among
other things.
- Renesas SH-PFC has added support for RPC pins, groups, and
functions to r8a77970 and r8a77980.
- The newere Freescale (now NXP) i.MX8 pin controllers have
been modularized. This is driven by the Google Android
GKI initiative I think.
- Open drain support for pins on the Qualcomm IPQ4019.
- The Ingenic driver can handle both edges IRQ detection.
- A big slew of documentation fixes all over the place.
- A few irqchip template conversions by yours truly.
-----BEGIN PGP SIGNATURE-----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=mJgb
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of the pin control changes for the v5.9 kernel
series:
Core changes:
- The GPIO patch "gpiolib: Introduce for_each_requested_gpio_in_range()
macro" was put in an immutable branch and merged into the pinctrl
tree as well. We see these changes also here.
- Improved debug output for pins used as GPIO.
New drivers:
- Ocelot Sparx5 SoC driver.
- Intel Emmitsburg SoC subdriver.
- Intel Tiger Lake-H SoC subdriver.
- Qualcomm PM660 SoC subdriver.
- Renesas SH-PFC R8A774E1 subdriver.
Driver improvements:
- Linear improvement and cleanups of the Intel drivers for
Cherryview, Lynxpoint, Baytrail etc. Improved locking among other
things.
- Renesas SH-PFC has added support for RPC pins, groups, and
functions to r8a77970 and r8a77980.
- The newere Freescale (now NXP) i.MX8 pin controllers have been
modularized. This is driven by the Google Android GKI initiative I
think.
- Open drain support for pins on the Qualcomm IPQ4019.
- The Ingenic driver can handle both edges IRQ detection.
- A big slew of documentation fixes all over the place.
- A few irqchip template conversions by yours truly.
* tag 'pinctrl-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (107 commits)
dt-bindings: pinctrl: add bindings for MediaTek MT6779 SoC
pinctrl: stmfx: Use irqchip template
pinctrl: amd: Use irqchip template
pinctrl: mediatek: fix build for tristate changes
pinctrl: samsung: Use bank name as irqchip name
pinctrl: core: print gpio in pins debugfs file
pinctrl: mediatek: add mt6779 eint support
pinctrl: mediatek: add pinctrl support for MT6779 SoC
pinctrl: mediatek: avoid virtual gpio trying to set reg
pinctrl: mediatek: update pinmux definitions for mt6779
pinctrl: stm32: use the hwspin_lock_timeout_in_atomic() API
pinctrl: mcp23s08: Use irqchip template
pinctrl: sx150x: Use irqchip template
dt-bindings: ingenic,pinctrl: Support pinmux/pinconf nodes
pinctrl: intel: Add Intel Emmitsburg pin controller support
pinctl: ti: iodelay: Replace HTTP links with HTTPS ones
Revert "gpio: omap: handle pin config bias flags"
pinctrl: single: Use fallthrough pseudo-keyword
pinctrl: qcom: spmi-gpio: Use fallthrough pseudo-keyword
pinctrl: baytrail: Use fallthrough pseudo-keyword
...
|
|
|
Douglas Anderson
|
c3c0c2e18d |
pinctrl: qcom: Handle broken/missing PDC dual edge IRQs on sc7180
Depending on how you look at it, you can either say that:
a) There is a PDC hardware issue (with the specific IP rev that exists
on sc7180) that causes the PDC not to work properly when configured
to handle dual edges.
b) The dual edge feature of the PDC hardware was only added in later
HW revisions and thus isn't in all hardware.
Regardless of how you look at it, let's work around the lack of dual
edge support by only ever letting our parent see requests for single
edge interrupts on affected hardware.
NOTE: it's possible that a driver requesting a dual edge interrupt
might get several edges coalesced into a single IRQ. For instance if
a line starts low and then goes high and low again, the driver that
requested the IRQ is not guaranteed to be called twice. However, it
is guaranteed that once the driver's interrupt handler starts running
its first instruction that any new edges coming in will cause the
interrupt to fire again. This is relatively commonplace for dual-edge
gpio interrupts (many gpio controllers require software to emulate
dual edge with single edge) so client drivers should be setup to
handle it.
Fixes:
|
|
|
Lee Jones
|
0b33c72a19 |
pinctrl: qcom: pinctrl-msm: Complete 'struct msm_pinctrl' documentation
Add missing descriptions for attributes and fix 1 formatting issue. Fixes the following W=1 kernel build warning(s): drivers/pinctrl/qcom/pinctrl-msm.c:75: warning: Function parameter or member 'desc' not described in 'msm_pinctrl' drivers/pinctrl/qcom/pinctrl-msm.c:75: warning: Function parameter or member 'irq_chip' not described in 'msm_pinctrl' drivers/pinctrl/qcom/pinctrl-msm.c:75: warning: Function parameter or member 'intr_target_use_scm' not described in 'msm_pinctrl' drivers/pinctrl/qcom/pinctrl-msm.c:75: warning: Function parameter or member 'soc' not described in 'msm_pinctrl' drivers/pinctrl/qcom/pinctrl-msm.c:75: warning: Function parameter or member 'phys_base' not described in 'msm_pinctrl' Signed-off-by: Lee Jones <lee.jones@linaro.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Andy Gross <agross@kernel.org> Cc: linux-arm-msm@vger.kernel.org Link: https://lore.kernel.org/r/20200713144930.1034632-6-lee.jones@linaro.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Jaiganesh Narayanan
|
13355ca35c |
pinctrl: qcom: ipq4019: add open drain support
[ Brian: adapted from from the Chromium OS kernel used on IPQ4019-based WiFi APs. ] Signed-off-by: Jaiganesh Narayanan <njaigane@codeaurora.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Link: https://lore.kernel.org/r/20200703080646.23233-1-computersforpeace@gmail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Linus Torvalds
|
cf0c97f148 |
This is the bulk of pin control changes for the v5.8
kernel cycle. New drivers: - Intel Jasper Lake support. - NXP Freescale i.MX8DXL support. - Qualcomm SM8250 support. - Renesas R8A7742 SH-PFC support. Driver improvements: - Severe cleanup and modernization of the MCP23s08 driver. - Mediatek driver modularized. - Setting config supported in the Meson driver. - Wakeup support for the Broadcom BCM7211. -----BEGIN PGP SIGNATURE----- iQIzBAABCAAdFiEElDRnuGcz/wPCXQWMQRCzN7AZXXMFAl7dZC4ACgkQQRCzN7AZ XXOEZg/9F4dCwXmMxMxbS1c7DSHxsJTEHYKDDgAZ0L36N2DHihpMGbVQFzEe9khK xeSS8M4ecACYzw3FJGESaEC+fmTZ7zxr60SR++iyJJptooKAmcA00d2M/4VQ4ggN P/nXFEsGJvQ7nNJSO95wXr5K8aVkQW7rjo1cnblXH0c9dYOp+ItyodIytKcdWeZ9 QfWSovYd+Oqra0braxx+pM/iTFVf6eOoCFZ8gkXB35pORsZ4Vl/e8pXMHXc3wUUm S1b6e3fifLiEGANvCEXz47/f3lUmUY26FsCSCAt92tHChq/p6coIKKvKyP4723PF R2L03iO8jMfsX+HwL2ivblSZ/lFExEgalWET56aogZClRQVynC0NMOnDEdluYGaT XJZPib9sRqQOF36+G9Bcy4zlqjj1LoHwqpiCdAhtj3AACTKdoLjDK0sJ3Wn5E8lJ QfIb+oqOmOGNHN/fdSsxsNM1ptOqNb/sW2Gk4O+X9tYzG17m16oZEVkrv4FNhmeC mePl/7aX+aMoHkEYxvt9tF3kRDFbndcuHdNFtRxq0Tx9jELiR91ySjjs9bUr2Vnl kkihtfIMZngQjBgHe2PNlcF2t7gSIgSBVEvwxslcUlx3XvVEDP16RKJV52aL80uu ev4k0h72CTxI1lZuNuW4cJYDKF/wJPqPtQ8+GQfOZxG7yuM8tOc= =3UGk -----END PGP SIGNATURE----- Merge tag 'pinctrl-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This is the bulk of pin control changes for the v5.8 kernel cycle. It's just really boring this time. Zero core changes. Just linear development, cleanups and misc noncritical fixes. Some new drivers for very new Qualcomm and Intel chips. New drivers: - Intel Jasper Lake support. - NXP Freescale i.MX8DXL support. - Qualcomm SM8250 support. - Renesas R8A7742 SH-PFC support. Driver improvements: - Severe cleanup and modernization of the MCP23s08 driver. - Mediatek driver modularized. - Setting config supported in the Meson driver. - Wakeup support for the Broadcom BCM7211" * tag 'pinctrl-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits) pinctrl: sprd: Fix the incorrect pull-up definition pinctrl: pxa: pxa2xx: Remove 'pxa2xx_pinctrl_exit()' which is unused and broken pinctrl: freescale: imx: Use 'devm_of_iomap()' to avoid a resource leak in case of error in 'imx_pinctrl_probe()' pinctrl: freescale: imx: Fix an error handling path in 'imx_pinctrl_probe()' pinctrl: sirf: add missing put_device() call in sirfsoc_gpio_probe() pinctrl: imxl: Fix an error handling path in 'imx1_pinctrl_core_probe()' pinctrl: bcm2835: Add support for wake-up interrupts pinctrl: bcm2835: Match BCM7211 compatible string dt-bindings: pinctrl: Document optional BCM7211 wake-up interrupts dt-bindings: pinctrl: Document 7211 compatible for brcm, bcm2835-gpio.txt dt-bindings: pinctrl: stm32: Add missing interrupts property pinctrl: at91-pio4: Add COMPILE_TEST support pinctrl: Fix return value about devm_platform_ioremap_resource() MAINTAINERS: Renesas Pin Controllers are supported dt-bindings: pinctrl: ocelot: Add Sparx5 SoC support pinctrl: ocelot: Fix GPIO interrupt decoding on Jaguar2 pinctrl: ocelot: Remove instance number from pin functions pinctrl: ocelot: Always register GPIO driver dt-bindings: pinctrl: rockchip: update example pinctrl: amd: Add ACPI dependency ... |
|
|
Venkata Narendra Kumar Gutta
|
dca4f40742 |
pinctrl: qcom: Add affinity callbacks to msmgpio IRQ chip
Wakeup capable GPIO IRQs routed via PDC are not being migrated when a CPU
is hotplugged. Add affinity callbacks to msmgpio IRQ chip to update the
affinity of wakeup capable IRQs.
Fixes:
|
|
|
YueHaibing
|
5da42a3d25 |
pinctrl: qcom: Remove duplicated include from pinctrl-msm.c
Remove duplicated include.
Fixes:
|
|
|
Ansuel Smith
|
90bcb0c3ca |
pinctrl: qcom: fix wrong write in update_dual_edge
Fix a typo in the readl/writel accessor conversion where val is used
instead of pol changing the behavior of the original code.
Cc: stable@vger.kernel.org
Fixes:
|
|
|
Linus Torvalds
|
bc3b3f4bfb |
This is the bulk of pin control changes for the v5.7 kernel cycle.
There are no core changes this time, only driver developments.
- New driver for the Dialog Semiconductor DA9062 Power Management
Integrated Circuit (PMIC).
- Renesas SH-PFC has improved consistency, with group and
register checks in the configuration checker.
- New subdriver for the Qualcomm IPQ6018.
- Add the RGMII pin control functionality to Qualcomm IPQ8064.
- Performance and code quality cleanups in the Mediatek
driver.
- Improve the Broadcom BCM2835 support to cover all the GPIOs
that exist in it.
- The Allwinner/Sunxi driver properly masks non-wakeup IRQs on
suspend.
- Add some missing groups and functions to the Ingenic driver.
- Convert some of the Freescale device tree bindings to use the
new and all improved JSON YAML markup.
- Refactorings and support for the SFIO/GPIO in the Tegra194
SoC driver.
- Support high impedance mode in the Spreadtrum/Unisoc driver.
-----BEGIN PGP SIGNATURE-----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=1ZKq
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.7 kernel cycle.
There are no core changes this time, only driver developments:
- New driver for the Dialog Semiconductor DA9062 Power Management
Integrated Circuit (PMIC).
- Renesas SH-PFC has improved consistency, with group and register
checks in the configuration checker.
- New subdriver for the Qualcomm IPQ6018.
- Add the RGMII pin control functionality to Qualcomm IPQ8064.
- Performance and code quality cleanups in the Mediatek driver.
- Improve the Broadcom BCM2835 support to cover all the GPIOs that
exist in it.
- The Allwinner/Sunxi driver properly masks non-wakeup IRQs on
suspend.
- Add some missing groups and functions to the Ingenic driver.
- Convert some of the Freescale device tree bindings to use the new
and all improved JSON YAML markup.
- Refactorings and support for the SFIO/GPIO in the Tegra194 SoC
driver.
- Support high impedance mode in the Spreadtrum/Unisoc driver"
* tag 'pinctrl-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (64 commits)
pinctrl: qcom: fix compilation error
pinctrl: qcom: use scm_call to route GPIO irq to Apps
pinctrl: sprd: Add pin high impedance mode support
pinctrl: sprd: Use the correct pin output configuration
pinctrl: tegra: Add SFIO/GPIO programming on Tegra194
pinctrl: tegra: Renumber the GG.0 and GG.1 pins
pinctrl: tegra: Do not add default pin range on Tegra194
pinctrl: tegra: Pass struct tegra_pmx for pin range check
pinctrl: tegra: Fix "Scmitt" -> "Schmitt" typo
pinctrl: tegra: Fix whitespace issues for improved readability
pinctrl: mediatek: Use scnprintf() for avoiding potential buffer overflow
pinctrl: freescale: drop the dependency on ARM64 for i.MX8M
Revert "pinctrl: mvebu: armada-37xx: use use platform api"
dt-bindings: pinctrl: at91: Fix a typo ("descibe")
pinctrl: meson: add tsin pinctrl for meson gxbb/gxl/gxm
pinctrl: sprd: Fix the kconfig warning
pinctrl: ingenic: add hdmi-ddc pin control group
pinctrl: sirf/atlas7: Replace zero-length array with flexible-array member
pinctrl: sprd: Allow the SPRD pinctrl driver building into a module
pinctrl: Export some needed symbols at module load time
...
|
|
|
Ansuel Smith
|
c42f69b420 |
pinctrl: qcom: fix compilation error
pinctrl: qcom: use scm_call to route GPIO irq to Apps has a typo in the
patch and introduced a compilation error.
Fixes:
|
|
|
Ajay Kishore
|
13bec8d49b |
pinctrl: qcom: use scm_call to route GPIO irq to Apps
For IPQ806x targets, TZ protects the registers that are used to configure the routing of interrupts to a target processor. To resolve this, this patch uses scm call to route GPIO interrupts to application processor. Also the scm call interface is changed. Signed-off-by: Ajay Kishore <akisho@codeaurora.org> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> Link: https://lore.kernel.org/r/20200327223209.20409-1-ansuelsmth@gmail.com Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Linus Walleij
|
1cada2f307 |
pinctrl: qcom: Assign irq_eoi conditionally
The hierarchical parts of MSM pinctrl/GPIO is only
used when the device tree has a "wakeup-parent" as
a phandle, but the .irq_eoi is anyway assigned leading
to semantic problems on elder Qualcomm chipsets.
When the drivers/mfd/qcom-pm8xxx.c driver calls
chained_irq_exit() that call will in turn call chip->irq_eoi()
which is set to irq_chip_eoi_parent() by default on a
hierachical IRQ chip, and the parent is pinctrl-msm.c
so that will in turn unconditionally call
irq_chip_eoi_parent() again, but its parent is invalid
so we get the following crash:
Unnable to handle kernel NULL pointer dereference at
virtual address 00000010
pgd = (ptrval)
[00000010] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
(...)
PC is at irq_chip_eoi_parent+0x4/0x10
LR is at pm8xxx_irq_handler+0x1b4/0x2d8
If we solve this crash by avoiding to call up to
irq_chip_eoi_parent(), the machine will hang and get
reset by the watchdog, because of semantic issues,
probably inside irq_chip.
As a solution, just assign the .irq_eoi conditionally if
we are actually using a wakeup parent.
Cc: David Heidelberg <david@ixit.cz>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: stable@vger.kernel.org
Fixes:
|
|
|
Matti Vaittinen
|
3c82787359 |
pinctrl: Use new GPIO_LINE_DIRECTION
Use newly added GPIO defines GPIO_LINE_DIRECTION_IN and GPIO_LINE_DIRECTION_OUT instead of using hard-coded 1 and 0. Main benefit is to make it easier to see which values mean IN and which OUT. As a side effect this helps GPIO framework to change the direction defines to something else if ever needed. Please note that return value from get_direction call on pinctrl-axp209 driver was changed. Previously pinctrl-axp209 might have returned value 2 for direction INPUT. Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> Reported-by: kbuild test robot <lkp@intel.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Link: https://lore.kernel.org/r/20200214135712.GA14557@localhost.localdomain Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Stephen Boyd
|
1d44616e75 |
pinctrl: qcom: Don't lock around irq_set_irq_wake()
We don't need to hold the local pinctrl lock here to set irq wake on the
summary irq line. Doing so only leads to lockdep warnings instead of
protecting us from anything. Remove the locking.
WARNING: possible circular locking dependency detected
5.4.11 #2 Tainted: G W
------------------------------------------------------
cat/3083 is trying to acquire lock:
ffffff81f4fa58c0 (&irq_desc_lock_class){-.-.}, at: __irq_get_desc_lock+0x64/0x94
but task is already holding lock:
ffffff81f4880c18 (&pctrl->lock){-.-.}, at: msm_gpio_irq_set_wake+0x48/0x7c
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&pctrl->lock){-.-.}:
_raw_spin_lock_irqsave+0x64/0x80
msm_gpio_irq_ack+0x68/0xf4
__irq_do_set_handler+0xe0/0x180
__irq_set_handler+0x60/0x9c
irq_domain_set_info+0x90/0xb4
gpiochip_hierarchy_irq_domain_alloc+0x110/0x200
__irq_domain_alloc_irqs+0x130/0x29c
irq_create_fwspec_mapping+0x1f0/0x300
irq_create_of_mapping+0x70/0x98
of_irq_get+0xa4/0xd4
spi_drv_probe+0x4c/0xb0
really_probe+0x138/0x3f0
driver_probe_device+0x70/0x140
__device_attach_driver+0x9c/0x110
bus_for_each_drv+0x88/0xd0
__device_attach+0xb0/0x160
device_initial_probe+0x20/0x2c
bus_probe_device+0x34/0x94
device_add+0x35c/0x3f0
spi_add_device+0xbc/0x194
of_register_spi_devices+0x2c8/0x408
spi_register_controller+0x57c/0x6fc
spi_geni_probe+0x260/0x328
platform_drv_probe+0x90/0xb0
really_probe+0x138/0x3f0
driver_probe_device+0x70/0x140
device_driver_attach+0x4c/0x6c
__driver_attach+0xcc/0x154
bus_for_each_dev+0x84/0xcc
driver_attach+0x2c/0x38
bus_add_driver+0x108/0x1fc
driver_register+0x64/0xf8
__platform_driver_register+0x4c/0x58
spi_geni_driver_init+0x1c/0x24
do_one_initcall+0x1a4/0x3e8
do_initcall_level+0xb4/0xcc
do_basic_setup+0x30/0x48
kernel_init_freeable+0x124/0x1a8
kernel_init+0x14/0x100
ret_from_fork+0x10/0x18
-> #0 (&irq_desc_lock_class){-.-.}:
__lock_acquire+0xeb4/0x2388
lock_acquire+0x1cc/0x210
_raw_spin_lock_irqsave+0x64/0x80
__irq_get_desc_lock+0x64/0x94
irq_set_irq_wake+0x40/0x144
msm_gpio_irq_set_wake+0x5c/0x7c
set_irq_wake_real+0x40/0x5c
irq_set_irq_wake+0x70/0x144
cros_ec_rtc_suspend+0x38/0x4c
platform_pm_suspend+0x34/0x60
dpm_run_callback+0x64/0xcc
__device_suspend+0x310/0x41c
dpm_suspend+0xf8/0x298
dpm_suspend_start+0x84/0xb4
suspend_devices_and_enter+0xbc/0x620
pm_suspend+0x210/0x348
state_store+0xb0/0x108
kobj_attr_store+0x14/0x24
sysfs_kf_write+0x4c/0x64
kernfs_fop_write+0x15c/0x1fc
__vfs_write+0x54/0x18c
vfs_write+0xe4/0x1a4
ksys_write+0x7c/0xe4
__arm64_sys_write+0x20/0x2c
el0_svc_common+0xa8/0x160
el0_svc_handler+0x7c/0x98
el0_svc+0x8/0xc
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&pctrl->lock);
lock(&irq_desc_lock_class);
lock(&pctrl->lock);
lock(&irq_desc_lock_class);
*** DEADLOCK ***
7 locks held by cat/3083:
#0: ffffff81f06d1420 (sb_writers#7){.+.+}, at: vfs_write+0xd0/0x1a4
#1: ffffff81c8935680 (&of->mutex){+.+.}, at: kernfs_fop_write+0x12c/0x1fc
#2: ffffff81f4c322f0 (kn->count#337){.+.+}, at: kernfs_fop_write+0x134/0x1fc
#3: ffffffe89a641d60 (system_transition_mutex){+.+.}, at: pm_suspend+0x108/0x348
#4: ffffff81f190e970 (&dev->mutex){....}, at: __device_suspend+0x168/0x41c
#5: ffffff81f183d8c0 (lock_class){-.-.}, at: __irq_get_desc_lock+0x64/0x94
#6: ffffff81f4880c18 (&pctrl->lock){-.-.}, at: msm_gpio_irq_set_wake+0x48/0x7c
stack backtrace:
CPU: 4 PID: 3083 Comm: cat Tainted: G W 5.4.11 #2
Hardware name: Google Cheza (rev3+) (DT)
Call trace:
dump_backtrace+0x0/0x174
show_stack+0x20/0x2c
dump_stack+0xc8/0x124
print_circular_bug+0x2ac/0x2c4
check_noncircular+0x1a0/0x1a8
__lock_acquire+0xeb4/0x2388
lock_acquire+0x1cc/0x210
_raw_spin_lock_irqsave+0x64/0x80
__irq_get_desc_lock+0x64/0x94
irq_set_irq_wake+0x40/0x144
msm_gpio_irq_set_wake+0x5c/0x7c
set_irq_wake_real+0x40/0x5c
irq_set_irq_wake+0x70/0x144
cros_ec_rtc_suspend+0x38/0x4c
platform_pm_suspend+0x34/0x60
dpm_run_callback+0x64/0xcc
__device_suspend+0x310/0x41c
dpm_suspend+0xf8/0x298
dpm_suspend_start+0x84/0xb4
suspend_devices_and_enter+0xbc/0x620
pm_suspend+0x210/0x348
state_store+0xb0/0x108
kobj_attr_store+0x14/0x24
sysfs_kf_write+0x4c/0x64
kernfs_fop_write+0x15c/0x1fc
__vfs_write+0x54/0x18c
vfs_write+0xe4/0x1a4
ksys_write+0x7c/0xe4
__arm64_sys_write+0x20/0x2c
el0_svc_common+0xa8/0x160
el0_svc_handler+0x7c/0x98
el0_svc+0x8/0xc
Fixes:
|
|
|
Linus Torvalds
|
b22bfea7f1 |
Merge branch 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Ingo Molnar: "Most of the IRQ subsystem changes in this cycle were irq-chip driver updates: - Qualcomm PDC wakeup interrupt support - Layerscape external IRQ support - Broadcom bcm7038 PM and wakeup support - Ingenic driver cleanup and modernization - GICv3 ITS preparation for GICv4.1 updates - GICv4 fixes There's also the series from Frederic Weisbecker that fixes memory ordering bugs for the irq-work logic, whose primary fix is to turn work->irq_work.flags into an atomic variable and then convert the complex (and buggy) atomic_cmpxchg() loop in irq_work_claim() into a much simpler atomic_fetch_or() call. There are also various smaller cleanups" * 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits) pinctrl/sdm845: Add PDC wakeup interrupt map for GPIOs pinctrl/msm: Setup GPIO chip in hierarchy irqchip/qcom-pdc: Add irqchip set/get state calls irqchip/qcom-pdc: Add irqdomain for wakeup capable GPIOs irqchip/qcom-pdc: Do not toggle IRQ_ENABLE during mask/unmask irqchip/qcom-pdc: Update max PDC interrupts of/irq: Document properties for wakeup interrupt parent genirq: Introduce irq_chip_get/set_parent_state calls irqdomain: Add bus token DOMAIN_BUS_WAKEUP genirq: Fix function documentation of __irq_alloc_descs() irq_work: Fix IRQ_WORK_BUSY bit clearing irqchip/ti-sci-inta: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(...)) irq_work: Slightly simplify IRQ_WORK_PENDING clearing irq_work: Fix irq_work_claim() memory ordering irq_work: Convert flags to atomic_t irqchip: Ingenic: Add process for more than one irq at the same time. irqchip: ingenic: Alloc generic chips from IRQ domain irqchip: ingenic: Get virq number from IRQ domain irqchip: ingenic: Error out if IRQ domain creation failed irqchip: ingenic: Drop redundant irq_suspend / irq_resume functions ... |
|
|
Lina Iyer
|
e35a6ae0eb |
pinctrl/msm: Setup GPIO chip in hierarchy
Some GPIOs are marked as wakeup capable and are routed to another interrupt controller that is an always-domain and can detect interrupts even when most of the SoC is powered off. The wakeup interrupt controller wakes up the GIC and replays the interrupt at the GIC. Setup the TLMM irqchip in hierarchy with the wakeup interrupt controller and ensure the wakeup GPIOs are handled correctly. Co-developed-by: Maulik Shah <mkshah@codeaurora.org> Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1573855915-9841-9-git-send-email-ilina@codeaurora.org ---- Changes in v2: - Address review comments - Fix Co-developed-by tag Changes in v1: - Address minor review comments - Remove redundant call to set irq handler - Move irq_domain_qcom_handle_wakeup() to this patch Changes in RFC v2: - Rebase on top of GPIO hierarchy support in linux-next - Set the chained irq handler for summary line |
|
|
YueHaibing
|
4b024225c4 |
pinctrl: use devm_platform_ioremap_resource() to simplify code
devm_platform_ioremap_resource() internally have platform_get_resource() and devm_ioremap_resource() in it. So instead of calling them separately use devm_platform_ioremap_resource() directly. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Thierry Reding <treding@nvidia.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20191104142654.39256-1-yuehaibing@huawei.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Linus Torvalds
|
3c2edc36a7 |
This is the bulk of pin control changes for the v5.4 kernel
cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to
the Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEElDRnuGcz/wPCXQWMQRCzN7AZXXMFAl2D6y0ACgkQQRCzN7AZ
XXNAfw//Zh0zkrwVSiDU7xgjIgLpngkmPeDoFZoPW5Uqh6G3KlabkE0y7CXZT2kd
hZU0v8CW/947t2zxNev6nNUPumfaTJsj5btVAvF8+QE2lnnbs3Id2mPVPK/mMUs+
bOVFkMMFvGzsY2TaKiJSgOiTe8LoUUl2tJ25mFRBwgtPWYJh2NLVwbzScv+KTBX2
Yy1UhltfWaobyPGgJucZn2yDbkZQeDLyKaExsL9jKBO9rAf8iwSOwkxEz5hLGRri
ejubLV2C5WDcAYIMO2WscFm/0Cxv8ooWBlGTG3+v3P1eaB7l7rYkGpVkoRJpS7gr
Qzf0z1PjVudCcwomkf7ZXJFVHCEkWe86oT4plII9TiZ0b5YpwxYA3Rzakrpb3K7E
gxCuMR1PQK9/2VcqtnXjV2N40KJNRhsAGx47YK3mZxFQun8ksLDTSwKCEPvQ5GT6
3CSYtqVkqgpRaj1MIe+QrFE5Y2bNPjYqXF8kqh5hz/2FWZErbaRuPuKscYh7x0Z4
wY157HEYTlSnSs3nHFtPO3qeXt0i2MNOKVpIlyKzUnafPoyxcnqaB/ZMt5Dp3ygX
NJI3xqULdSzXRpjj/oChCKzuNd9CmxO6yWMIK32f4Gdc3T1wmpBlOTIrHKUA5aZf
KN38L/8iGnzvOKC57552eFpTXaF4Plh2y7e0xQkq4eshhHpz8H8=
=2nNz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.4 kernel cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to the
Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver"
* tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (112 commits)
pinctrl: meson-gxbb: Fix wrong pinning definition for uart_c
pinctrl: sh-pfc: Unlock on error in sh_pfc_func_set_mux()
pinctrl: bcm: remove redundant assignment to pointer log
pinctrl: iproc: Add 'get_direction' support
pinctrl: iproc-gpio: Handle interrupts for multiple instances
pinctrl: iproc-gpio: Fix incorrect pinconf configurations
pinctrl: intel: mark intel_pin_to_gpio __maybe_unused
pinctrl: qcom: sdm845: Fix UFS_RESET pin
pinctrl: mvebu: add additional variant for standalone CP115
pinctrl: mvebu: Add CP110 missing pin functionality
dt-bindings: cp110: document the new CP115 pinctrl compatible
pinctrl: bcm2835: Pass irqchip when adding gpiochip
pinctrl: meson: meson: Add of_node_put() before return
pinctrl/gpio: Take MUX usage into account
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150l support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150b support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150 support
pinctrl: amd: disable spurious-firing GPIO IRQs
pinctrl: rza2: Include the appropriate headers
pinctrl: rza2: Drop driver use of consumer flags
...
|
|
|
Linus Walleij
|
eb1e8bd6e3 |
gpio: Use callback presence to determine need of valid_mask
After we switched the two drivers that have .need_valid_mask set to use the callback for setting up the .valid_mask, we can just use the presence of the .init_valid_mask() callback (or the OF reserved ranges, nota bene) to determine whether to allocate the mask or not and we can drop the .need_valid_mask field altogether. Cc: Benjamin Gaignard <benjamin.gaignard@st.com> Cc: Amelie Delaunay <amelie.delaunay@st.com> Cc: Stephen Boyd <swboyd@chromium.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190819093058.10863-1-linus.walleij@linaro.org |
|
|
Linus Walleij
|
c9fc5aff21 |
gpio: Pass mask and size with the init_valid_mask()
It is more helpful for drivers to have the affected fields directly available when we use the callback to set up the valid mask. Change this and switch over the only user (MSM) to use the passed parameters. If we do this we can also move the mask out of publicly visible struct fields. Cc: Stephen Boyd <swboyd@chromium.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190819084904.30027-1-linus.walleij@linaro.or Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Stephen Boyd
|
64c4dcbfcc |
pinctrl: Remove dev_err() usage after platform_get_irq()
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-34-swboyd@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
Andy Shevchenko
|
720b8ec676 |
pinctrl: msm: Switch to use device_property_count_uXX()
Use use device_property_count_uXX() directly, that makes code neater. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20190723192738.68486-1-andriy.shevchenko@linux.intel.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Linus Walleij
|
0ce242ad2e |
pinctrl: qcom: Pass irqchip when adding gpiochip
We need to convert all old gpio irqchips to pass the irqchip setup along when adding the gpio_chip. For chained irqchips this is a pretty straight-forward conversion. Cc: Thierry Reding <treding@nvidia.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Co-developed-by: Lina Iyer <ilina@codeaurora.org> Link: https://lore.kernel.org/r/20190724083828.7496-1-linus.walleij@linaro.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Linus Torvalds
|
43c95d3694 |
This is the bulk of pin control changes for the v5.3 kernel
cycle:
Core changes:
- Device links can optionally be added between a pin control
producer and its consumers. This will affect how the system
power management is handled: a pin controller will not suspend
before all of its consumers have been suspended. This was
necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense
to make this default in the long run. Right now it is
opt-in per driver.
- Drive strength can be specified in microamps. With decreases
in silicon technology, milliamps isn't granular enough, let's
make it possible to select drive strengths in microamps. Right
now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a
product line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in
addition to muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken
aside and not usable for users. This is used in ACPI systems
to take out some GPIO lines used by the BIOS so that
noone else (neither kernel nor userspace) will play with them
by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board
management controllers for servers) in preparation for the
new Aspeed AST2600 SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=Wdw1
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.3 kernel cycle:
Core changes:
- Device links can optionally be added between a pin control producer
and its consumers. This will affect how the system power management
is handled: a pin controller will not suspend before all of its
consumers have been suspended.
This was necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense to make
this default in the long run.
Right now it is opt-in per driver.
- Drive strength can be specified in microamps. With decreases in
silicon technology, milliamps isn't granular enough, let's make it
possible to select drive strengths in microamps.
Right now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a product
line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in addition to
muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken aside and
not usable for users. This is used in ACPI systems to take out some
GPIO lines used by the BIOS so that noone else (neither kernel nor
userspace) will play with them by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board management
controllers for servers) in preparation for the new Aspeed AST2600
SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes"
* tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (106 commits)
pinctrl: aspeed: Strip moved macros and structs from private header
pinctrl: aspeed: Fix missed include
pinctrl: baytrail: Use GENMASK() consistently
pinctrl: baytrail: Re-use data structures from pinctrl-intel.h
pinctrl: baytrail: Use defined macro instead of magic in byt_get_gpio_mux()
pinctrl: qcom: Add SM8150 pinctrl driver
dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding
dt-bindings: pinctrl: qcom: Document missing gpio nodes
pinctrl: aspeed: Add implementation-related documentation
pinctrl: aspeed: Split out pinmux from general pinctrl
pinctrl: aspeed: Clarify comment about strapping W1C
pinctrl: aspeed: Correct comment that is no longer true
MAINTAINERS: Add entry for ASPEED pinctrl drivers
dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema
dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema
dt-bindings: pinctrl: aspeed: Split bindings document in two
pinctrl: qcom: Add irq_enable callback for msm gpio
pinctrl: madera: Fixup SPDX headers
pinctrl: qcom: sdm845: Fix CONFIG preprocessor guard
pinctrl: tegra: Add bitmask support for parked bits
...
|
|
|
Srinivas Ramana
|
4b7618fdc7 |
pinctrl: qcom: Add irq_enable callback for msm gpio
Introduce the irq_enable callback which will be same as irq_unmask except that it will also clear the status bit before unmask. This will help in clearing any erroneous interrupts that would have got latched when the interrupt is not in use. There may be devices like UART which can use the same gpio line for data rx as well as a wakeup gpio when in suspend. The data that was flowing on the line may latch the interrupt and when we enable the interrupt before going to suspend, this would trigger the unexpected interrupt. This change helps clearing the interrupt so that these unexpected interrupts gets cleared. Signed-off-by: Srinivas Ramana <sramana@codeaurora.org> Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org> Link: https://lore.kernel.org/r/1561472086-23360-1-git-send-email-neeraju@codeaurora.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Lee Jones
|
4c0efbfb26 |
pinctrl: msm: Add ability for drivers to supply a reserved GPIO list
When booting MSM based platforms with Device Tree or some ACPI implementations, it is possible to provide a list of reserved pins via the 'gpio-reserved-ranges' and 'gpios' properties respectively. However some ACPI tables are not populated with this information, thus it has to come from a knowledgable device driver instead. Here we provide the MSM common driver with additional support to parse this informtion and correctly populate the widely used 'valid_mask'. Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Thomas Gleixner
|
97fb5e8d9b |
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 284
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 and only version 2 as published by the free software foundation this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 294 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Alexios Zavras <alexios.zavras@intel.com> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
|
|
Arnd Bergmann
|
d1040ea06f |
pinctrl: msm: mark PM functions as __maybe_unused
Without CONFIG_PM_SLEEP, we get annoying warnings about unused functions:
drivers/pinctrl/qcom/pinctrl-msm.c:1082:12: error: 'msm_pinctrl_resume' defined but not used [-Werror=unused-function]
static int msm_pinctrl_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~
drivers/pinctrl/qcom/pinctrl-msm.c:1075:12: error: 'msm_pinctrl_suspend' defined but not used [-Werror=unused-function]
static int msm_pinctrl_suspend(struct device *dev)
Mark them as __maybe_unused to shut up the warning and silently drop
the functions without having to add ugly #ifdefs.
Fixes:
|
|
|
Evan Green
|
977d057ad3 |
pinctrl: msm: Add sleep pinctrl state transitions
Add PM suspend callbacks to the msm core driver that select the sleep and default pinctrl states. Then wire those callbacks up in the sdm845 driver, for those boards that may have GPIO hogs that need to change state during suspend. Signed-off-by: Evan Green <evgreen@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Linus Torvalds
|
114b5f8f7e |
This is the bulk of GPIO changes for the v4.20 series:
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO
lines as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can
use only the fastpatch callbacks to enable/disable irqs
like any normal irqchip, especially the gpiod_lock_as_irq()
has been improved to be callable in fastpath context.
A bunch of rework had to be done to achieve this but it is
a big win since I never liked to restrict this to slowpath.
The only call requireing slowpath was try_module_get() and
this is kept at the .request_resources() slowpath callback.
In the GPIO CEC driver this is a big win sine a single
line is used for both outgoing and incoming traffic, and
this needs to use IRQs for incoming traffic while actively
driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a
"cookie" (struct gpio_array) and a bitmap for setting or
getting multiple GPIO lines at once. This improvement
orginated in a specific need to speed up an OMAP1 driver and
has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot
of checks and code when we want things to go really fast.
The previous code would minimize the number of calls
down to the driver callbacks assuming the CPU speed was
orders of magnitude faster than the I/O latency, but this
assumption was wrong on several platforms: what we needed
to do was to profile and improve the speed on the hot
path of the array functions and this change is now
completed.
- Clean out the painful and hard to grasp BNF experiments
from the device tree bindings. Future approaches are looking
into using JSON schema for this purpose. (Rob Herring
is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and
other contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin
control driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver.
-----BEGIN PGP SIGNATURE-----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=YosT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.20 series:
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO lines
as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can use only
the fastpatch callbacks to enable/disable irqs like any normal
irqchip, especially the gpiod_lock_as_irq() has been improved to be
callable in fastpath context.
A bunch of rework had to be done to achieve this but it is a big
win since I never liked to restrict this to slowpath. The only call
requireing slowpath was try_module_get() and this is kept at the
.request_resources() slowpath callback. In the GPIO CEC driver this
is a big win sine a single line is used for both outgoing and
incoming traffic, and this needs to use IRQs for incoming traffic
while actively driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a "cookie"
(struct gpio_array) and a bitmap for setting or getting multiple
GPIO lines at once.
This improvement orginated in a specific need to speed up an OMAP1
driver and has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot of checks
and code when we want things to go really fast.
The previous code would minimize the number of calls down to the
driver callbacks assuming the CPU speed was orders of magnitude
faster than the I/O latency, but this assumption was wrong on
several platforms: what we needed to do was to profile and improve
the speed on the hot path of the array functions and this change is
now completed.
- Clean out the painful and hard to grasp BNF experiments from the
device tree bindings. Future approaches are looking into using JSON
schema for this purpose. (Rob Herring is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and other
contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin control
driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver"
* tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (116 commits)
gpio: Clarify kerneldoc on gpiochip_set_chained_irqchip()
gpio: Remove unused 'irqchip' argument to gpiochip_set_cascaded_irqchip()
gpio: Drop parent irq assignment during cascade setup
mmc: pwrseq_simple: Fix incorrect handling of GPIO bitmap
gpio: fix SNPS_CREG kconfig dependency warning
gpiolib: Initialize gdev field before is used
gpio: fix kernel-doc after devres.c file rename
gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
gpio: syscon: Fix possible NULL ptr usage
gpiolib: Show correct direction from the beginning
pinctrl: msm: Use init_valid_mask exported function
gpiolib: Add init_valid_mask exported function
GPIO: add single-register GPIO via CREG driver
dt-bindings: Document the Synopsys GPIO via CREG bindings
gpio: mockup: use device properties instead of platform_data
gpio: Slightly more helpful debugfs
gpio: omap: Remove set but not used variable 'dev'
gpio: omap: drop omap_gpio_list
Accept partial 'gpio-line-names' property.
gpio: omap: get rid of the conditional PM runtime calls
...
|
|
|
Ricardo Ribalda Delgado
|
6f0ec09afe |
pinctrl: msm: Use init_valid_mask exported function
The current code produces XPU violation if get_direction is called just after the initialization. Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Acked-by: Timur Tabi <timur@kernel.org> Tested-by: Jeffrey Hugo <jhugo@codeaurora.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Stephen Boyd
|
de0c18a87c |
pinctrl: msm: Actually use function 0 for gpio selection
This code needs to select function #0, which is the first int in the
array of functions, not the number 0 which may or may not be the
function for "GPIO mode" per the enum mapping. We were getting lucky on
SDM845, where this was tested, because the function 0 matched the enum
value for "GPIO mode". On other platforms, e.g. MSM8996, the gpio enum
value is the last one in the list so this code doesn't work and we see a
warning at boot. Fix it by grabbing the first element out of the array
of functions.
Cc: Doug Anderson <dianders@chromium.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Niklas Cassel <niklas.cassel@linaro.org>
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Fixes:
|
|
|
Linus Walleij
|
30aa69e7bd |
This is the 4.19-rc6 release
-----BEGIN PGP SIGNATURE----- iQIzBAABCAAdFiEEZH8oZUiU471FcZm+ONu9yGCSaT4FAluw4MIACgkQONu9yGCS aT7+8xAAiYnc4khUsxeInm3z44WPfRX1+UF51frTNSY5C8Nn5nvRSnTUNLuKkkrz 8RbwCL6UYyJxF9I/oZdHPsPOD4IxXkQY55tBjz7ZbSBIFEwYM6RJMm8mAGlXY7wq VyWA5MhlpGHM9DjrguB4DMRipnrSc06CVAnC+ZyKLjzblzU1Wdf2dYu+AW9pUVXP j4r74lFED5djPY1xfqfzEwmYRCeEGYGx7zMqT3GrrF5uFPqj1H6O5klEsAhIZvdl IWnJTU2coC8R/Sd17g4lHWPIeQNnMUGIUbu+PhIrZ/lDwFxlocg4BvarPXEdzgYi gdZzKBfovpEsSu5RCQsKWG4IGQxY7I1p70IOP9eqEFHZy77qT1YcHVAWrK1Y/bJd UA08gUOSzRnhKkNR3+PsaMflUOl9WkpyHECZu394cyRGMutSS50aWkavJPJ/o1Qi D/oGqZLLcKFyuNcchG+Met1TzY3LvYEDgSburqwqeUZWtAsGs8kmiiq7qvmXx4zV IcgM8ERqJ8mbfhfsXQU7hwydIrPJ3JdIq19RnM5ajbv2Q4C/qJCyAKkQoacrlKR4 aiow/qvyNrP80rpXfPJB8/8PiWeDtAnnGhM+xySZNlw3t8GR6NYpUkIzf5TdkSb3 C8KuKg6FY9QAS62fv+5KK3LB/wbQanxaPNruQFGe5K1iDQ5Fvzw= =dMl4 -----END PGP SIGNATURE----- Merge tag 'v4.19-rc6' into devel This is the 4.19-rc6 release I needed to merge this in because of extensive conflicts in the MSM and Intel pin control drivers. I know how to resolve them, so let's do it like this. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Bjorn Andersson
|
a46d5e9819 |
pinctrl: qcom: Support dispersed tiles
On some new platforms the tiles have been placed too far apart to be covered in a single ioremap. Turn "regs" into an array of base addresses and make the pingroup carry the information about which tile the pin resides in. For existing platforms we map the first entry regs and the existing pingroups will all use tile 0, meaning that there's no functional change. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Bjorn Andersson
|
6c73698904 |
pinctrl: qcom: Introduce readl/writel accessors
In preparation for the support for dispersed tiles move all readl and writel calls to helper functions. This will allow us to isolate the added complexity of another indirection. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Linus Walleij
|
1c5fb66afa |
pinctrl: Include <linux/gpio/driver.h> nothing else
These drivers are GPIO drivers, and the do not need to use the legacy header in <linux/gpio.h>, go directly for <linux/gpio/driver.h> instead. Replace any use of GPIOF_* with 0/1, these flags are for consumers, not drivers. Get rid of a few gpio_to_irq() users that was littering around the place, use local callbacks or avoid using it at all. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Stephen Boyd
|
fe2731211e |
pinctrl: msm: Configure interrupts as input and gpio mode
When requesting a gpio as an interrupt, we should make sure to mux the pin as the GPIO function and configure it to be an input so that various functions or output signals don't affect the interrupt state of the pin. So far, we've relied on pinmux configurations in DT to handle this, but let's explicitly configure this in the code so that DT implementers don't have to get this part right. Cc: Doug Anderson <dianders@chromium.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Stephen Boyd
|
1de7ddb3a1 |
pinctrl: msm: Mux out gpio function with gpio_request()
We rely on devices to use pinmuxing configurations in DT to select the GPIO function (function 0) if they're going to use the gpio in GPIO mode. Let's simplify things for driver authors by implementing gpio_request_enable() for this pinctrl driver to mux out the GPIO function when the gpio is use from gpiolib. Cc: Doug Anderson <dianders@chromium.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Stephen Boyd
|
b55326dc96 |
pinctrl: msm: Really mask level interrupts to prevent latching
The interrupt controller hardware in this pin controller has two status enable bits. The first "normal" status enable bit enables or disables the summary interrupt line being raised when a gpio interrupt triggers and the "raw" status enable bit allows or prevents the hardware from latching an interrupt into the status register for a gpio interrupt. Currently we just toggle the "normal" status enable bit in the mask and unmask ops so that the summary irq interrupt going to the CPU's interrupt controller doesn't trigger for the masked gpio interrupt. For a level triggered interrupt, the flow would be as follows: the pin controller sees the interrupt, latches the status into the status register, raises the summary irq to the CPU, summary irq handler runs and calls handle_level_irq(), handle_level_irq() masks and acks the gpio interrupt, the interrupt handler runs, and finally unmask the interrupt. When the interrupt handler completes, we expect that the interrupt line level will go back to the deasserted state so the genirq code can unmask the interrupt without it triggering again. If we only mask the interrupt by clearing the "normal" status enable bit then we'll ack the interrupt but it will continue to show up as pending in the status register because the raw status bit is enabled, the hardware hasn't deasserted the line, and thus the asserted state latches into the status register again. When the hardware deasserts the interrupt the pin controller still thinks there is a pending unserviced level interrupt because it latched it earlier. This behavior causes software to see an extra interrupt for level type interrupts each time the interrupt is handled. Let's fix this by clearing the raw status enable bit for level type interrupts so that the hardware stops latching the status of the interrupt after we ack it. We don't do this for edge type interrupts because it seems that toggling the raw status enable bit for edge type interrupts causes spurious edge interrupts. Signed-off-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Douglas Anderson
|
05e0c82895 |
pinctrl: msm: Fix msm_config_group_get() to be compliant
If you do this on an sdm845 board:
cat /sys/kernel/debug/pinctrl/3400000.pinctrl/pinconf-groups
...it looks like nonsense. For every pin you see listed:
input bias bus hold, input bias disabled, input bias pull down, input bias pull up
That's because msm_config_group_get() isn't complying with the rules
that pinconf_generic_dump_one() expects. Specifically for boolean
parameters (anything with a "struct pin_config_item" where has_arg is
false) the function expects that the function should return its value
not through the "config" parameter but should return "0" if the value
is set and "-EINVAL" if the value isn't set.
Let's fix this.
From a quick sample of other pinctrl drivers, it appears to be
tradition to also return 1 through the config parameter for these
boolean parameters when they exist. I'm not one to knock tradition,
so I'll follow tradition and return 1 in these cases. While I'm at
it, I'll also continue searching for four leaf clovers, kocking on
wood three times, and trying not to break mirrors.
Fixes:
|