... in preparation for common clock coming for Integrator
and Versatile Express.
Based on Linus Walleij's "ARM: integrator: convert to common
clock" patch.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
With recent enough motherboard firmware, core tile can be fitted
in either of the two daughterboard sites. The non-DT tile code for
V2P-CA9 did not check that when configuring DVI output nor setting
CLCD pixel clock.
Fixed now, providing "get master site" API in motherboard's code.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
The vexpress Kconfig setup tries to be clever^Whelpful and selects some
errata workarounds for certain revisions of the Cortex-A9 and PL310,
which may be required depending on the core tile.
Since the mach-vexpress can support A5, A7 and A15 coretiles, let's
make errata workaround selection optional.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Rob Herring <robherring2@gmail.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
In SGMII riser card different PHY chip are used with different external
IRQ from eTSEC. To support PHY link state auto detect in SGMII mode we
should add another group of PHY nodes for SGMII mode.
For MPC8572DS IRQ6 is used for PHY0~PHY1, IRQ7 is used for PHY2~PHY3.
For MPC8544DS and MPC8536DS IRQ6 is used for PHY0~PHY1.
For P2020DS IRQ5 is used for PHY1~PHY2.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A number of older ColdFire CPU based boards use NS8390 based network
controllers. Most use the Davicom 9008F or the UMC 9008F. This driver
provides the support code to get these devices working on these platforms.
Generally the NS8390 based eth device is direct connected via the general
purpose bus of the ColdFire CPU. So its addressing and interrupt setup is
fixed on each of the different platforms (classic platform setup).
This driver is based on the other drivers/net/ethernet/8390 drivers, and
includes the lib8390.c code. It uses the existing definitions of the
board NS8390 device addresses, interrupts and access types from the
arch/m68k/include/asm/mcf8390.h, but moves the IO access functions into
the driver code and out of that header.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mcfne.h include contains definitions to support NS8390 eth based hardware
on ColdFire based CPU boards. So change its name to reflect that better.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From Roland Stigge <stigge@antcom.de>:
This is the pull request including the fix for the compile error caused
by lpc32xx-next and dma branches collisions in linux-next.
* 'lpc32xx/core-fixes' of git://git.antcom.de/linux-2.6:
ARM: LPC32xx: Adjust to pl08x DMA interface changes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adjusts the LPC32xx platform support to the new pl08x DMA interface,
fixing the compile error resulting from changed pl08x structures.
Signed-off-by: Roland Stigge <stigge@antcom.de>
This patch handles PCID/INVPCID for guests.
Process-context identifiers (PCIDs) are a facility by which a logical processor
may cache information for multiple linear-address spaces so that the processor
may retain cached information when software switches to a different linear
address space. Refer to section 4.10.1 in IA32 Intel Software Developer's Manual
Volume 3A for details.
For guests with EPT, the PCID feature is enabled and INVPCID behaves as running
natively.
For guests without EPT, the PCID feature is disabled and INVPCID triggers #UD.
Signed-off-by: Junjie Mao <junjie.mao@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Commit ca1d72f033 ('PM / Domains: Make it possible to add devices to
inactive domains') introduced possibility to add devices to inactive
power domains and added pm_genpd_dev_need_restore() function which lets
platform core to notify power domain core that the specified device must
be restored (with its runtime_resume() callback) before first use.
This patch adds the pm_genpd_dev_need_restore() call what brings back
the suspend/resume behaviour for the client devices known from the
previous power domain driver (removed by commit 91cfbd4ee0 - 'ARM:
EXYNOS: Hook up power domains to generic power domain infrastructure').
Client device drivers relay on that suspend/resume behaviour, thus this
patch fixes runtime pm operation for client devices.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Some bootloaders disable unused power domains to reduce power
consuption. Power domain driver can easily read the actual state from
the hardware registers instead of assuming that their initial state is
always 'on'.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
When SYS_WDTRESET is set, watchdog timer reset request
is ignored by power management unit.
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
During imx6q initialization the usb charger detector is disabled but
for it, ANATOP controller symbols need to be available.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Imx6q sabrelite board uses ecspi1 to connect a spi flash sst25vf016b,
we need to add pinctrl information for it in the dts, otherwise the
ecspi1 driver can't work and the connected flash is wrongly
detected as a mr25h256 flash like this:
m25p80 spi32766.0: found mr25h256, expected sst25vf016b
m25p80 spi32766.0: mr25h256 (32 Kbytes)
Cc: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The external charger detector needs to be disabled,
or the signal at DP will be poor
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The macros just called BUG(), but that results in unused variable
warnings all over the place, like in the IPMI driver. The build
regression emails were annoying me, so here's the fix. I have
not even compile tested this, but it's rather obvious.
[ port type mangled to unsigned long ]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds real clock support to Calxeda Highbank SOC using the common
clock infrastructure.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
[mturquette@linaro.org: fixed up invalid writes to const struct member]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This converts the Integrator platform to use common clock
and the ICST driver. Since from this point not all ARM
reference platforms use the clock, we define
CONFIG_PLAT_VERSATILE_CLOCK and select it for all platforms
except the Integrator.
Open issue: I could not use the .init_early() field of the
machine descriptor to initialize the clocks, but had to
move them to .init_irq(), so presumably .init_early() is
so early that common clock is not up, and .init_machine()
is too late since it's needed for the clockevent/clocksource
initialization. Any suggestions on how to solve this is
very welcome.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[mturquette@linaro.org: use 'select' instead of versatile Kconfig]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
All the Integrator devices have bus names like "mb:16" which
I think means "memory base 0x16000000" which is where the
UART0 is. So let's call it "uart0" because that's what most
platforms do these days.
Change this everywhere for the integrator as we prepare for
some core clock code movement.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Fix the build error:
include/linux/regset.h: In function 'user_regset_copyout_zero':
include/linux/regset.h:289:3: error: implicit declaration of function '__clear_user' [-Werror=implicit-function-declaration]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__gu_val is const if the passed ptr is const, giving:
include/linux/pagemap.h: In function 'fault_in_pages_readable':
include/linux/pagemap.h:442:2: error: assignment of read-only variable '__gu_val'
include/linux/pagemap.h:448:4: error: assignment of read-only variable '__gu_val'
include/linux/pagemap.h: In function 'fault_in_multipages_readable':
include/linux/pagemap.h:499:3: error: assignment of read-only variable '__gu_val'
include/linux/pagemap.h:508:3: error: assignment of read-only variable '__gu_val'
make[4]: *** [init/main.o] Error 1
As we don't care about the actual value of __gu_val in the unhandled
case (it will cause a link error anyway), just remove the assignment.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the build error:
arch/h8300/kernel/time.c: In function 'h8300_timer_tick':
arch/h8300/kernel/time.c:39:2: error: implicit declaration of function 'get_irq_regs' [-Werror=implicit-function-declaration]
arch/h8300/kernel/time.c:39:42: error: invalid type argument of '->' (have 'int')
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The keyword is "static", not "statis":
arch/h8300/kernel/signal.c:455:8: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'void'
arch/h8300/kernel/signal.c: In function 'do_notify_resume':
arch/h8300/kernel/signal.c:511:3: error: implicit declaration of function 'do_signal' [-Werror=implicit-function-declaration]
arch/h8300/kernel/signal.c: At top level:
arch/h8300/kernel/signal.c:414:1: warning: 'handle_signal' defined but not used [-Wunused-function]
Introduced in commit 7ae4e32a65 ("h8300: switch to saved_sigmask-based
sigsuspend/rt_sigsuspend")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the h8300 build error:
kernel/sched/core.c: In function 'context_switch':
kernel/sched/core.c:2061:2: error: implicit declaration of function 'arch_start_context_switch' [-Werror=implicit-function-declaration]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the warnings:
arch/mn10300/kernel/irq.c:173:7: warning: "CONFIG_MN10300_TTYSM1_TIMER9" is not defined [-Wundef]
arch/mn10300/kernel/irq.c:175:7: warning: "CONFIG_MN10300_TTYSM1_TIMER3" is not defined [-Wundef]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the warnings:
arch/mn10300/mm/dma-alloc.c: At top level:
arch/mn10300/mm/dma-alloc.c:63:1: warning: data definition has no type or storage class [enabled by default]
arch/mn10300/mm/dma-alloc.c:63:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Wimplicit-int]
arch/mn10300/mm/dma-alloc.c:63:1: warning: parameter names (without types) in function declaration [enabled by default]
arch/mn10300/mm/dma-alloc.c:75:1: warning: data definition has no type or storage class [enabled by default]
arch/mn10300/mm/dma-alloc.c:75:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Wimplicit-int]
arch/mn10300/mm/dma-alloc.c:75:1: warning: parameter names (without types) in function declaration [enabled by default]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the warning:
arch/mn10300/kernel/traps.c:304:1: warning: data definition has no type or storage class [enabled by default]
arch/mn10300/kernel/traps.c:304:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Wimplicit-int]
arch/mn10300/kernel/traps.c:304:1: warning: parameter names (without types) in function declaration [enabled by default]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the nm10300 build failure:
In file included from arch/mn10300/kernel/csrc-mn10300.c:14:0:
arch/mn10300/kernel/internal.h:42:1: error: unknown type name 'irqreturn_t'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the warning:
include/linux/ptrace.h:66:0: warning: "PTRACE_O_TRACESYSGOOD" redefined [enabled by default]
arch/mn10300/include/asm/ptrace.h:85:0: note: this is the location of the previous definition
We already have it in <linux/ptrace.h>, so remove it from <asm/ptrace.h>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the static inline function setup_jiffies_interrupt() from
<asm/timex.h> to arch/mn10300/kernel/cevt-mn10300.c, which is its only
callsite.
This allows to remove the inclusion of <asm/hardirq.h> and <linux/irq.h>
from <asm/timex.h> and <unit/timex.h>, fixing include hell like:
include/linux/jiffies.h:260:31: warning: "CLOCK_TICK_RATE" is not defined [-Wundef]
include/linux/jiffies.h:260:31: warning: "CLOCK_TICK_RATE" is not defined [-Wundef]
include/linux/jiffies.h:46:42: error: division by zero in #if
...
make[4]: *** [arch/mn10300/kernel/asm-offsets.s] Error 1
and (after a quick hack for the above by defining CLOCK_TICK_RATE in
<linux/jiffies.h>):
In file included from include/linux/notifier.h:15:0,
from include/linux/memory_hotplug.h:6,
from include/linux/mmzone.h:718,
from include/linux/gfp.h:4,
from include/linux/irq.h:20,
from arch/mn10300/unit-asb2303/include/unit/timex.h:15,
from arch/mn10300/include/asm/timex.h:15,
from include/linux/timex.h:174,
from include/linux/jiffies.h:8,
from include/linux/ktime.h:25,
from include/linux/timer.h:5,
from include/linux/workqueue.h:8,
include/linux/srcu.h:55:22: error: field 'work' has incomplete type
As a consequence, we do need a few more inclusions of <asm/irq.h>, namely
in arch/mn10300/unit-asb2303/smc91111.c and
arch/mn10300/unit-asb2305/unit-init.c.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This converts the U300 clock implementation over to use the common
struct clk and moves the implementation down into drivers/clk.
Since VCO isn't used in tree it was removed, it's not hard to
put it back in if need be.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[mturquette@linaro.org: trivial Makefile conflict]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Provide kernel support for the tilegx "Transaction I/O" (TRIO) on-chip
hardware. This hardware implements the PCIe interface for tilegx;
the driver changes to use TRIO for PCIe are in a subsequent commit.
The change is layered on top of the tilegx GXIO IORPC subsystem.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The TILE-Gx chip includes a packet-processing network engine called
mPIPE ("Multicore Programmable Intelligent Packet Engine"). This
change adds support for using the mPIPE engine from within the
kernel. The engine has more functionality than is exposed here,
but to keep the kernel code and binary simpler, this is a subset
of the full API designed to enable standard Linux networking only.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The dma_queue support is used by both the mPipe (networking)
and Trio (PCI) hardware shims on tilegx. This common code is
selected when either of those drivers is built.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Add support for MMIO read/write on tilegx to support GXIO IORPC access.
Similar to the asm-generic version, but we include memory fences on
the writes to be conservative.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The GXIO I/O RPC subsystem handles exporting I/O hardware resources to
Linux and to applications running under Linux.
For instance, memory which is made available for I/O DMA must be mapped
by an I/O TLB; that means that such memory must be locked down by Linux,
so that it is not swapped or otherwise reused, as long as those I/O
TLB entries are active. Similarly, configuring direct hardware access
introduces new validation requirements. If a user application registers
memory, Linux must ensure that the supplied virtual addresses are valid,
and turn them into client physical addresses. Similarly, when Linux then
supplies those client physical addresses to the Tilera hypervisor, it
must in turn validate those before turning them into the real physical
addresses which are required by the hardware.
To the extent that these sorts of activities were required on previous
TILE architecture processors, they were implemented in a device-specific
fashion. This meant that every I/O device had its own Tilera hypervisor
driver, its own Linux driver, and in some cases its own user-level
library support. There was a large amount of more-or-less functionally
identical code in different places, particularly in the different Linux
drivers. For TILE-Gx, this support has been generalized into a common
framework, known as the I/O RPC framework or just IORPC.
The two "gxio" directories (one for headers, one for sources) start
with just a few files in each with this infrastructure commit, but
after adding support for the on-board I/O shims for networking, PCI,
USB, crypto, compression, I2CS, etc., there end up being about 20 files
in each directory.
More information on the IORPC framework is in the <hv/iorpc.h> header,
included in this commit.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Pull arch/tile fix from Chris Metcalf:
"This is a single change to fix backtracing in big-endian mode."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: big-endian: properly bswap instruction bundles when backtracing
* multiple omap2+ bug fixes
* a regression on ux500 dt support
* a build failure on shmobile
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=35LO
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
- multiple omap2+ bug fixes
- a regression on ux500 dt support
- a build failure on shmobile
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP2+: omap2plus_defconfig: EHCI driver is not stable, disable it
ARM: shmobile: fix platsmp.c build when ARCH_SH73A0=n
ARM: ux500: Over-ride the DT device naming scheme for pinctrl
ARM: ux500: Fix build errors/warnings when MACH_UX500_DT is not set
of: address: Don't fail a lookup just because a node has no reg property
ARM: OMAP2+: hwmod code/clockdomain data: fix 32K sync timer
The declaration of arch_release_thread_info() needs a semicolon.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit dad1743e59 ("x86/mce: Only restart instruction after machine
check recovery if it is safe") we fixed mce_notify_process() to force a
signal to the current process if it was not restartable (RIPV bit not
set in MCG_STATUS). But doing it here means that the process doesn't
get told the virtual address of the fault via siginfo_t->si_addr. This
would prevent application level recovery from the fault.
Make a new MF_MUST_KILL flag bit for memory_failure() et al. to use so
that we will provide the right information with the signal.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: stable@kernel.org # 3.4+
While debugging I noticed that unlike all the other hypervisor code in the
kernel, kvm does not have an entry for x86_hyper which is used in
detect_hypervisor_platform() which results in a nice printk in the
syslog. This is only really a stub function but it
does make kvm more consistent with the other hypervisors.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Marcelo Tostatti <mtosatti@redhat.com>
Cc: kvm@vger.kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
PPC fix from Alex Graf: "It contains an important bug fix which
can lead to guest freezes when using PAPR guests with PR KVM."
* 'for-upstream-master' of git://github.com/agraf/linux-2.6:
powerpc/kvm: Fix "PR" KVM implementation of H_CEDE
Signed-off-by: Avi Kivity <avi@redhat.com>
rfci instruction and CSRR0/1 registers are emulated.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
tlbilxva emulation was using an u32 variable for guest effective address.
Replace it with gva_t type to handle 64-bit guests.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
64-bit host needs to remain in 64-bit mode when an exception take place.
Set interrupt computaion mode in EPCR register.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
ESR register is required by Data Storage Interrupt handling code.
Add the specific flag to the interrupt handler.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Watchdog is taken at critical exception level. So this patch
is tested with host watchdog exception happening when guest
is running.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
H_CEDE should enable the vcpu's MSR:EE bit. It does on "HV" KVM (it's
burried in the assembly code though) and as far as I can tell, qemu
does it as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The P bit of page fault error code is missed in this tracepoint, fix it by
passing the full error code
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
To see what happen on this path and help us to optimize it
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If the the present bit of page fault error code is set, it indicates
the shadow page is populated on all levels, it means what we do is
only modify the access bit which can be done out of mmu-lock
Currently, in order to simplify the code, we only fix the page fault
caused by write-protect on the fast path
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This bit indicates whether the spte can be writable on MMU, that means
the corresponding gpte is writable and the corresponding gfn is not
protected by shadow page protection
In the later path, SPTE_MMU_WRITEABLE will indicates whether the spte
can be locklessly updated
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
mmu_spte_update() is the common function, we can easily audit the path
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Export the present bit of page fault error code, the later patch
will use it
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Use __drop_large_spte to cleanup this function and comment spte_write_protect
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Introduce a common function to abstract spte write-protect to
cleanup the code
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The reture value of __rmap_write_protect is either 1 or 0, use
true/false instead of these
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This gives the kernel a paravirtualized machine to target, without
requiring both sides to pretend to be targeting a specific board
that likely has little to do with the host in KVM scenarios. This
avoids the need to add new boards to QEMU just to be able to
run KVM on new CPUs.
As this is the first platform that can run with either e500v2 or
e500mc, CONFIG_PPC_E500MC is now a legitimately user configurable
option, so add a help text.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Similar to how the primary PCI bridge is identified by looking
for an isa subnode, we determine whether to apply uli exclusions
by looking for a uli subnode.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As an alternative incremental starting point to Jia Hongtao's patchset,
get the FSL PCI init out of the board files, but do not yet convert to a
platform driver.
Rather than having each board supply a magic register offset for
determining the "primary" bus, we look for which PCI host bridge
contains an ISA node within its subtree. If there is no ISA node,
normally that would mean there is no primary bus, but until certain
bugs are fixed we arbitrarily designate a primary in this case.
Conversion to a platform driver and related improvements can happen
after this, as the ordering issues are sorted out.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Enable NAND support
- Enable CONFIG_PCI_MSI and CONFIG_MMC_SDHCI_OF
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The board is really P1021RDB-PC, so rename from p1021rdb.* to p1021rdb-pc.*
Signed-off-by: Xu Jiucheng <Jiucheng.Xu@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently, BOOKE watchdog code for checking "wdt" and "wdt_period" is
in setup_32.c, it cannot be used in 64-bit, so move it to a common place
setup-common.c, which will be shared by 32-bit and 64-bit.
Also, replace the simple_strtoul with kstrtol.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some power systems do not have legacy ISA devices. So, /dev/port is not
a valid interface on these systems. User level tools such as kbdrate is
trying to access the device using this interface which is causing the
system crash.
This patch will fix this issue by not creating this interface on these
powerpc systems.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rename mxs dts files with soc name being the prefix, so that the board
dts file can be located easily by soc name, and we also gain the
consistency of naming.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- Add sound support
- Enable mtd support
- Enable i.MX NAND support
- Enable NOR flash support
- Enable JFFS2/UBI
- Enable clk debugfs support
- Disable iommu support which is not present on i.MX
- Enable MC13xxx RTC
- Enable RNGA random number generator
- Enable SPI EEPROM support
- Enable I2C EEPROM support
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
prom_update_property() currently fails if the property doesn't
actually exist yet which isn't what we want. Change to add-or-update
instead of update-only, then we can remove a lot duplicated lines.
Suggested-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add "memory" attribute in inline assembly language as a compiler
barrier to make sure 4.6.x GCC don't reorder mfmsr().
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@vger.kernel.org
Just like the module loader, ftrace needs to be updated to use r12
instead of r11 with newer gcc's.
Signed-off-by: Roger Blofeld <blofeldus@yahoo.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@vger.kernel.org
If arch_validate_hwbkpt_settings() fails, bp->ctx won't be valid and the
kernel panics. Add a check to fix this.
Reported-by: Edjunior Barbosa Machado <emachado@linux.vnet.ibm.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This allows the linker to know that calls to them do not need to switch
TOC and stop errors like the following when linking large configurations:
powerpc64-linux-ld: drivers/built-in.o: In function `.gpiochip_is_requested':
(.text+0x4): sibling call optimization to `_savegpr0_29' does not allow automatic multiple TOCs; recompile with -mminimal-toc or -fno-optimize-sibling-calls, or make `_savegpr0_29' extern
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a request for a fast method of getting CPU and NUMA node IDs
from userspace. This patch implements a getcpu VDSO function,
similar to x86.
Ben suggested we use SPRG3 which is userspace readable. SPRG3 can be
modified by a KVM guest, so we save the SPRG3 value in the paca and
restore it when transitioning from the guest to the host.
I have a glibc patch that implements sched_getcpu on top of this.
Testing on a POWER7:
baseline: 538 cycles
vdso: 30 cycles
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Purely for cosmetic purposes, otherwise it can appear that we are in
single_step_pSeries() which is slightly confusing.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently the call to pseries_notify_cpuidle_add_cpu(), that takes
action on the cpuidle front when a cpu is added/removed
is being made from smp_xics_setup_cpu().
This caused lockdep issues as
reported https://lkml.org/lkml/2012/5/17/2
On addition of each cpu,
resources were cleared and re-allocated each time, all in critical
section as part of start_secondary() call were interrupts are disabled.
To resolve this issue, the pseries_notify_cpuidle_add_cpu() call is
is being replaced by a hotplug notifier which
would prevent cpuidle resources from being
released and allocated each time cpu is onlined in the critical code path.
It was fixed in https://lkml.org/lkml/2012/5/18/174.
Also it is essential to call cpuidle_enable/disable_device
between cpuidle_pause_and_lock() and
cpuidle_resume_and_unlock() when used externally
to avoid race conditions. Add support for CPU_ONLINE_FROZEN
and CPU_DEAD_FROZEN as part of hotplug notify event for
pseries_idle and unregister hotplug notifier
while exiting out. The above mentioned issues
are fixed as part of this patch.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When I "fixed" the CONFIG_TRACE_IRQFLAGS case on interrupt entry,
I screwed up a little bit with the test for user space vs. kernel.
The code is fine, there's just some dead code around it. I basically
removed the test and always create the added stack frame whether
coming from user or kernel since in any case we do need to save
a bunch of volatile registers or bad things would happen (we can
take page faults in the kernel for example).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
AUART3 is not available anymore. Pins are used as GPIOs.
Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add HannStar display and device tree configuration.
Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add dtb-y target into Makefile.boot, so that "make ARCH=arm dtbs" can
build out all the dtbs listed there. It's very useful for build-testing
all the <board>.dts when imx28.dtsi changes.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The enc28j60 spi device does not get converted to dts file, because
there is no mxs spi driver on mainline so far. The enc28j60 spi
in mach-stmp378x_devb.c does not work anyway.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
FEC support is missing because we need to find a proper way to rewrite
tx28_add_fec0 for device tree boot.
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The presence and muxing of lcdif control pins can vary much on different
boards. Move them into imx28-evk.dts to make lcdif_24bit_pins_a only
about data pins, so that it can be reused by other boards.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Only pins GPMI_CE0N and GPMI_READY0 are generally used by other boards.
Move GPMI_CE1N and GPMI_READY1 into imx28-evk.dts to make gpmi_pins_a
more general, and can be used by other boards.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- Invalid context restore on bank 0 for OMAP driver in
runtime suspend/resume cycle
- Check for NULL platform data in sta-2x11 driver
- Constrain selection of the V1 MSM GPIO driver to applicable
platforms (Kconfig issue)
- Make sure the correct output value is set in the wm8994 driver
- Export devm_gpio_request_one() so it can be used in modules.
Apparently some in-kernel modules can be configured to use this
leading to breakage.
- Check that the GPIO is valid in the lantiq driver
- Fix the flag bits introduced for v3.5, so they don't overlap
- Fix a device tree intialization bug for imx21-compatible devices
- Carry over the OF node to the TPS65910 GPIO chip struct
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GIRC
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Yes, this is a *LATE* GPIO pull request with fixes for v3.5.
Grant moved across the planet and accidentally fell off the grid, so
he asked me to take over the GPIO merges for a while 10 days ago.
Since then I went over the archives and collected this pile of fixes,
and pulled two of them from the TI maintainer Kevin Hilman. Then
waited for them to at least hit linux-next once or twice."
GPIO fixes for v3.5:
- Invalid context restore on bank 0 for OMAP driver in runtime
suspend/resume cycle
- Check for NULL platform data in sta-2x11 driver
- Constrain selection of the V1 MSM GPIO driver to applicable platforms
(Kconfig issue)
- Make sure the correct output value is set in the wm8994 driver
- Export devm_gpio_request_one() so it can be used in modules.
Apparently some in-kernel modules can be configured to use this
leading to breakage.
- Check that the GPIO is valid in the lantiq driver
- Fix the flag bits introduced for v3.5, so they don't overlap
- Fix a device tree intialization bug for imx21-compatible devices
- Carry over the OF node to the TPS65910 GPIO chip struct
* tag 'fixes-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tps65910: initialize of_node of gpio_chip
gpio/mxc: make irqs work for fsl,imx21-gpio devices
gpio: fix bits conflict for gpio flags
mips: pci-lantiq: Fix check for valid gpio
gpio: export devm_gpio_request_one
gpiolib: wm8994: Pay attention to the value set when enabling as output
gpio/msm_v1: CONFIG_GPIO_MSM_V1 is only available on three SoCs
gpio-sta2x11: don't use pdata if null
gpio/omap: fix invalid context restore of gpio bank-0
gpio/omap: fix irq loss while in idle with debounce on
Only the main UART and the memory node information are added.
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds basic devicetree support for i.MX31 based SoCs.
Only the UART and interrupts bindings are added.
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
From Tony Lindgren <tony@atomide.com>:
This branch contains minimal support for omap5 to boot to a
console without clock framework support. This branch depends
on omap-cleanup-part2-for-v3.6.
* 'devel-omap5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: Kconfig update to support additional GPIOs in OMAP5
ARM: OMAP5: Add the build support
arm/dts: OMAP5: Add omap5 dts files
ARM: OMAP5: board-generic: Add device tree support
ARM: omap2+: board-generic: clean up the irq data from board file
ARM: OMAP5: Add SMP support
ARM: OMAP5: Add the WakeupGen IP updates
ARM: OMAP5: l3: Add l3 error handler support for omap5
ARM: OMAP5: gpmc: Update gpmc_init()
ARM: OMAP5: timer: Add clocksource, clockevent support
ARM: OMAP5: Add minimal support for OMAP5430 SOC
ARM: OMAP5: id: Add cpu id for ES versions
ARM: OMAP: counter-32k: Select the CR register offset using the IP scheme
ARM: OMAP2+: Move stubbed secure_sram_reserve function to a common.c and call it __weak
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
will use the common clock framework, but those patches are not quite
ready yet for omaps. This branch depends on omap-cleanup-part2-for-v3.6
branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GF3s
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-am33xx-data-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/clk
From Tony Lindgren <tony@atomide.com>:
This branch adds clock data for am33xx. Note that eventually these
will use the common clock framework, but those patches are not quite
ready yet for omaps. This branch depends on omap-cleanup-part2-for-v3.6
branch.
* tag 'omap-devel-am33xx-data-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3+: clock33xx: Add AM33XX clock tree data
ARM: OMAP3+: clock: Move common clksel_rate & clock data to common file
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* pci/bjorn-p2p-bridge-windows:
sparc/PCI: replace pci_cfg_fake_ranges() with pci_read_bridge_bases()
PCI: support sizing P2P bridge I/O windows with 1K granularity
PCI: reimplement P2P bridge 1K I/O windows (Intel P64H2)
PCI: allow P2P bridge windows starting at PCI bus address zero
Conflicts:
drivers/pci/probe.c
include/linux/pci.h
The generic code to read P2P bridge windows is functionally equivalent
to the sparc-specific pci_cfg_fake_ranges(), so use the generic code.
The "if (!res->start) res->start = ..." removed from the I/O window code
here was an artifact of the Intel 1K window support from 9d265124d0 and
is no longer necessary (it probably was just cloned from x86 and was never
useful on sparc).
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Fix an interrupt handling issue with cp_intc which
was causing occasional spurious interrupts with DA850 EVM
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=3h/9
-----END PGP SIGNATURE-----
Merge tag 'davinci-v3.6-fixes' of git://gitorious.org/linux-davinci/linux-davinci into next/fixes-non-critical
DaVinci fixes for v3.6
Fix an interrupt handling issue with cp_intc which
was causing occasional spurious interrupts with DA850 EVM
* tag 'davinci-v3.6-fixes' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: da8xx: fix interrupt handling
Add IRQ domain support for cp_intc and
runtime PM core support for DaVinci devices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=8+Mw
-----END PGP SIGNATURE-----
Merge tag 'davinci-v3.6-soc' of git://gitorious.org/linux-davinci/linux-davinci into next/soc
From Sekhar Nori <nsekhar@ti.com>:
DaVinci SoC updates for v3.6
Add IRQ domain support for cp_intc and
runtime PM core support for DaVinci devices.
* tag 'davinci-v3.6-soc' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: add runtime PM support for clock management
ARM: davinci: cp_intc: Add irq domain support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove some header files which were marked for removal. These files are
not used anymore.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=NR2J
-----END PGP SIGNATURE-----
Merge tag 'davinci-v3.6-cleanup' of git://gitorious.org/linux-davinci/linux-davinci into next/cleanup
From: Sekhar Nori <nsekhar@ti.com>
DaVinci cleanups for v3.6
Remove some header files which were marked for removal. These files are
not used anymore.
* tag 'davinci-v3.6-cleanup' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: remove dummy header files
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
echi-omap because the driver currently causes issues with PM.
This annoys Kevin as it makes it harder for him to validate that
PM is working. The proper fixes for the echi-omap are being
discussed, but looks like it will not be properly working with PM
until in v3.7.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=+Kkw
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-for-v3.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren <tony@atomide.com>:
Here is one PM regression fix and a defconfig change to disable
echi-omap because the driver currently causes issues with PM.
This annoys Kevin as it makes it harder for him to validate that
PM is working. The proper fixes for the echi-omap are being
discussed, but looks like it will not be properly working with PM
until in v3.7.
* tag 'omap-fixes-for-v3.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap2plus_defconfig: EHCI driver is not stable, disable it
ARM: OMAP2+: hwmod code/clockdomain data: fix 32K sync timer
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Read the number of MPIC interrupts from the controller and only register
that many.
[gregory.clement@free-electrons.com: rename armada symbol name to fit
with new name: armada_370_xp]
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Lior Amsalem <alior@marvell.com>
[ben.dooks@codethink.co.uk: ensure error check on of_property_read_u32]
[ben.dooks@codethink.co.uk: use mpic address instead of bus-unit's ]
[ben.dooks@codethink.co.uk: BUG_ON() if the of_iomap() fails for mpic]
[ben.dooks@codethink.co.uk: move mpic per-cpu register base ]
[ben.dooks@codethink.co.uk: number fetch should use irqd_to_hwirq()]
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Yehuda Yitschak <yehuday@marvell.com>
Tested-by: Lior Amsalem <alior@marvell.com>
Add device tree nodes to enable ucc uart support on P1025RDB.
Signed-off-by: Zhicheng Fan <B32736@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
From Kukjin Kim <kgene.kim@samsung.com>:
* 'next/board-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C64XX: Add IRQ mapping for wm0010 on Cragganmore
ARM: S5PV210: Add HSOTG support to SMDKV210
ARM: EXYNOS: Update keypad entries for SMDK4X12
ARM: S3C64XX: Dynamically assign interrupts for CPU PMIC on Cragganmore
ARM: S3C64XX: Dynamically allocate the IRQ range for WM8994 on Cragganmore
ARM: S3C64XX: Add WM5102 EVM to Cragganmore modules
ARM: S3C64XX: Add module identification for Balblair Cragganmore module
ARM: EXYNOS: Add HSOTG support to SMDKV310
ARM: EXYNOS: Add HSOTG support to Origen
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Kukjin Kim <kgene.kim@samsung.com>:
Here is updating DMA common operation for Samsung SoCs.
Since some DMA client driver such as spi needs to change the configuration
after dma_request() so this branch adds dma_config() can configure DMA
transmit option which is included in dma_request() after that.
Note, according to the changes, needs to update spi and ASoC drivers
for Samsung SoCs and only got the ack from Mark Brown not Grant Likely
and as I know, he is busy for moving. But I think, the spi change has
no problem and it is simple.
* 'next/devel-dma-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: Fix compiler warning in dma-ops.c file
ASoC: follow the updated samsung DMA common operations
spi/s3c64xx: Add the use of DMA config operation
ARM: SAMSUNG: Add config() function in DMA common operations
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Kukjin Kim <kgene.kim@samsung.com>:
Samsung cleanup patches for v3.6 and most of them are removing
useless codes
* 'next/cleanup-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Remove the L2 cache latency setting for EXYNOS5
ARM: EXYNOS: Remove leftovers of the Samsung specific power domain control
ARM: SAMSUNG: Remove unused variable 'running' on PWM
ARM: SAMSUNG: remove unused SPI clock headers
ARM: S3C24XX: remove unused header <mach/bast-pmu.h>
ARM: S3C24XX: Remove duplicate header file inclusion
ARM: SAMSUNG: Remove description corresponding to a deleted element
ARM: S5PC100: Remove unused variable in dma.c file
ARM: S5P64X0: Remove unused variable in dma.c file
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Freescale PowerPC SoCs share a number of IP blocks with Freescale
ARM/IMX SoCs, FlexCAN, SSI, FEC, eSDHC, USB, etc. There are some
effort consolidating those drivers to make them work for both
architectures.
One outstanding difference between two architectures is ARM/IMX will
turn off module clocks during platform initialization for power saving
and expects drivers manage clocks using clk API, while PowerPC
mostly does not do that, and thus does not always build in clk API.
Listing all those driver Kconfig options in "select PPC_CLOCK if" seems
not scalable for long term maintenance, and could easily introduce
Kconfig recursive dependency. This patch chooses to select PPC_CLOCK
unconditionally for FSL_SOC to always build clk API for PowerPC in.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
QE Microcode Initialization using qe_upload_microcode() does not work on
P1021 if the IRAM-Ready register is not set after the microcode upload. Add
a definition for the "I-RAM Ready" register and sets it upon microcode
upload completion.
Signed-off-by: Ioannis Kokkoris <ioannis.kokoris@siemens-enterprise.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With 2-cell format interrupts of MSI PCIe ethernet card can not work.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We should use the MPIC_LARG_VECTORS flag while intializing the MPIC.
This prevents us from eating in to hardware vector number space (MSIs)
while setting up internal sources.
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
So that we can call it when improving SPE switch like book3e did for fp
switch.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Olivia Yin <hong-hua.yin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
BSC9131RDB is a Freescale reference design board for BSC9131 SoC. The
BSC9131 is integrated SoC that targets Femto base station market. It
combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.
The BSC9131 SoC includes the following function and features:
. Power Architecture subsystem including a e500 processor with 256-Kbyte
shared L2 cache
. StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
. The Multi Accelerator Platform Engine for Femto BaseStation Baseband
Processing (MAPLE-B2F)
. A multi-standard baseband algorithm accelerator for Channel
Decoding/Encoding, Fourier Transforms, UMTS chip rate processing, LTE
UP/DL Channel processing, and CRC algorithms
. Consists of accelerators for Convolution, Filtering, Turbo Encoding,
Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix
Inversion operations
. DDR3/3L memory interface with 32-bit data width without ECC and 16-bit
with ECC, up to 400-MHz clock/800 MHz data rate
. Dedicated security engine featuring trusted boot
. DMA controller
. OCNDMA with four bidirectional channels
. Interfaces
. Two triple-speed Gigabit Ethernet controllers featuring network
acceleration including IEEE 1588. v2 hardware support and
virtualization (eTSEC)
. eTSEC 1 supports RGMII/RMII
. eTSEC 2 supports RGMII
. High-speed USB 2.0 host and device controller with ULPI interface
. Enhanced secure digital (SD/MMC) host controller (eSDHC)
. Antenna interface controller (AIC), supporting three industry standard
JESD207/three custom ADI RF interfaces (two dual port and one single
port) and three MAXIM's MaxPHY serial interfaces
. ADI lanes support both full duplex FDD support and half duplex TDD
support
. Universal Subscriber Identity Module (USIM) interface that facilitates
communication to SIM cards or Eurochip pre-paid phone cards
. TDM with one TDM port
. Two DUART, four eSPI, and two I2C controllers
. Integrated Flash memory controller (IFC)
. TDM with 256 channels
. GPIO
. Sixteen 32-bit timers
The DSP portion of the SoC consists of DSP core (SC3850) and various
accelerators pertaining to DSP operations.
BSC9131RDB Overview
----------------------
BSC9131 SoC
1Gbyte DDR3 (on board DDR)
128Mbyte 2K page size NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
USB-ULPI
eTSEC1: Connected to RGMII PHY
eTSEC2: Connected to RGMII PHY
DUART interface: supports one UARTs up to 115200 bps for console display
Linux runs on e500v2 core and access some DSP peripherals like AIC
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit 96cc017c5b.
The P3060 was cancelled before it went into production, so there's no point
in supporting it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In order to enable the DIU video controller on the P1022DS, the FPGA needs
to be switched to "indirect mode", where the localbus is disabled and
the FPGA is accessed via writes to localbus chip select signals CS0 and CS1.
To obtain the address of CS0 and CS1, the platform driver uses an "indirect
pixis mode" device tree node. This node assumes that the localbus 'ranges'
property is sorted in chip-select order. That is, reg value 0 maps to
CS0, reg value 1 maps to CS1, etc. This is how the 'ranges' property is
supposed to be arranged.
Unfortunately, the 'ranges' property is often mis-arranged, and not just on
the P1022DS. Linux normally does not care, since it does not program the
localbus. But the indirect-mode code on the P1022DS does care.
The "proper" fix is to have U-Boot fix the 'ranges' property, but this would
be too cumbersome. The names and 'reg' properties of all the localbus
devices would also need to be updated, and determining which localbus device
maps to which chip select is board-specific.
Instead, we determine the CS0/CS1 base addresses the same way that U-boot
does -- by reading the BRx registers directly and mapping them to physical
addresses. This code is simpler and more reliable, and it does not require
a U-boot or device tree change.
Since the indirect pixis device tree node is no longer needed, the node is
deleted from the DTS.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reference board dates back to 2004, and is largely a legacy
EOL product. The MPC8560 is a pre e500v2 CPU. The SBC8548 is
a more modern, better e500v2 target for people to use as a
reference board with today's kernels, should they require one.
Removing support for it will also allow us to remove some
sbc8560 specific quirk handling in 8250 UART code, and some
MTD mapping support.
Cc: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The p1024rdb has the similar feature as the p1020rdb. Therefore, p1024rdb use
the same platform file as the p1/p2 rdb board.
Overview of P2020RDB platform
- DDR3 1G
- NOR flash 16M
- 3 Ethernet interfaces
- NAND Flash 32M
- SPI EEPROM 16M
- SD/MMC
- 2 USB ports
- 4 TDM ports
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add EEPROM to the P1010RDB device tree.
The 24c01 acts as a memory SPD so it shouldn't be overwritten without
care.
The 24c256 is a general purpose memory.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit 0c00f65653.
The initial commit was my fault. There are two boards out there:
P2020RDB and P2020RDB-PC. I wasn't aware of that and assumed that I have
a RDB board in front of me while I the RDB-PC. This patch makes it work
for the RDB-PC variant and breaks it for the RDB. Now there is a device
tree file available for the RDB-PC which was not there earlier. So with
this revert, everything gets back to normal :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add spi support for mgcoge into the platform code and the dts
file. Additionaly SPIDEV is switched on in the defconfig and the
updates for the newer kernel version are committed. The SPI
interface is used to drive the Maxim DS3106 clock chip.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Switch on UBIFS, HOTPLUG and TIPC and update the config to
the latest kernel version.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix RGMII workaround code in km83xx.c for MPC8360E and MPC8358E that it
correctly identifes all affected SoC chip models and applies the
workarounds appropriate for 2.0 and 2.1 revisions as per Freescale
MPC8360ECE Errata document Rev.5(9/2011) item QE_ENET10.
Signed-off-by: Christian Herzig <christian.herzig@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the RTC support into the p1022ds device tree
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable MTD/NOR/NAND options by default in mpc85xx_defconfig and
mpc85xx_smp_defconfig to support NOR, NAND flash.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
At least for crypto/IPSec, doing so provides users with a better
performance experience out of the box.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Change quirk_fsl_pcie_header from __init to __devinit to ensure if we
have a runtime access (like via an FPGA being loaded after boot on the
PCIe link) that we dont access randomly freed memory.
Signed-off-by: Matias Garcia <mgarcia@rossvideo.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Matt added BPF_JIT support in commit 0ca87f05, but currently none of our
defconfigs build it. Turn that sucker on.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add the ability to inject IOMMU faults. We enable this per device
via a fail_iommu sysfs property, similar to fault injection on other
subsystems.
An example:
...
0003:01:00.1 Ethernet controller: Emulex Corporation OneConnect 10Gb NIC (be3) (rev 02)
To inject one error to this device:
echo 1 > /sys/bus/pci/devices/0003:01:00.1/fail_iommu
echo 1 > /sys/kernel/debug/fail_iommu/probability
echo 1 > /sys/kernel/debug/fail_iommu/times
As feared, the first failure injected on the be3 results in an
unrecoverable error, taking down both functions of the card
permanently:
be2net 0003:01:00.1: Unrecoverable error in the card
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The DMA API debug code has hooks to verify all DMA entries have been
freed at time of hot unplug. We need to call dma_debug_add_bus for
this to work.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Similar to PCI, separate the bus probe from device probe. This allows
us to attach bus notifiers for DMA debug and IOMMU fault injection
before devices have been probed.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During boot we see a number of these warnings:
vio 30000000: Warning: IOMMU dma not supported: mask 0xffffffffffffffff, table unavailable
The reason for this is that we set IOMMU properties for all VIO
devices even if they are not DMA capable.
Only set DMA ops, table and mask for devices with a DMA window.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We use SIAR or regs->nip for the instruction pointer depending on
the PMU configuration, but we always use regs->nip in the callchain.
Use perf_instruction_pointer so the backtrace is consistent.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At the moment we always use the SIAR if the PMU supports continuous
sampling. Unfortunately the SIAR and the PMU exception are not
synchronised for non marked events so we can end up with callchains
that dont make sense.
The following patch checks the HV and PR bits for samples coming from
userspace and always uses pt_regs for them. Userspace will never have
interrupts off so there is no real advantage to using the SIAR for
non marked events in userspace.
I had experimented with a patch that did a similar thing for kernel
samples but we lost a significant amount of information. I was
unable to profile any of our early exception code for example.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The logic to choose whether to use the SIAR or get the information
out of pt_regs is going to get more complicated, so do it once in
perf_read_regs.
We overload regs->result which is gross but we are already doing it
with regs->dsisr.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We want to access the MMCRA_SIHV and MMCRA_SIPR bits elsewhere so
create mmcra_sihv and mmcra_sipr which hide the differences between
the old and new layout of the bits.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some macros use RA where when RA=R0 the values is 0, so make this
the enforced mnemonic in the macro.
Idea suggested by Andreas Schwab.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enforce the use of R0-R31 in macros where possible now we have all the
fixes in.
R0-R31 macros are removed here so that can't be used anymore. They
should not be defined anywhere.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now have ___PPC_RA/B/S/T we can use it in some places. These are
places where we can't use the existing defines which will soon enforce
R0-R31 usage.
The macros being changed here are being used in inline asm, which
can't convert to enforce the R0-R31 usage.
bpf_jit uses a mix of both generated and non-generated with the same
code, so just convert all these to use the ___PPC_R versions which
won't enforce R usage later.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These are currently the same as __PPC_RA/B/S/T but we'll wrap them
soon.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to do this so we can enforce the name of a and b in called
macros PPC_RA/B later.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These macros are using integers where they could be using logical
names since they take registers.
We are going to enforce this soon, so fix these up now.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
LOAD_REG_ADDR define is just a wrapper around real instructions so we
can just use real register names here (ie. lower case).
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
mtocrf define is just a wrapper around the real instructions so we can
just use real register names here (ie. lower case).
Also remove braces in macro so this is possible.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Move this duplicated definition to ppc_asm.h and remove the
braces which prevent the use of %rN register names
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Merge the defines of VCPU_GPR from different places.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Merge the defines of STACKFRAMESIZE, STK_REG, STK_PARAM from different
places.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now all the fixes are in place, let's rock-n-roll!
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anything that uses a constructed instruction (ie. from ppc-opcode.h),
need to use the new R0 macro, as %r0 is not going to work.
Also convert usages of macros where we are just determining an offset
(usually for a load/store), like:
std r14,STK_REG(r14)(r1)
Can't use STK_REG(r14) as %r14 doesn't work in the STK_REG macro since
it's just calculating an offset.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The assembler doesn't take %r0 register arguments in braces, so remove them.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are going to use these later and convert r0 to %r0 etc.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Newer gcc are being a bit blind here (it's pretty obvious we don't
reach the code path using the array if we haven't initialized the
pointer) but none of that is performance critical so let's just
silence it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There was a typo, checking for CONFIG_TRACE_IRQFLAG instead of
CONFIG_TRACE_IRQFLAGS causing some useful debug code to not be
built
This in turns causes a build error on BookE 64-bit due to incorrect
semicolons at the end of a couple of macros, so let's fix that too
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@vger.kernel.org [v3.4]
Looks like we still have issues with pSeries and Cell idle code
vs. the lazy irq state. In fact, the reset fixes that went upstream
are exposing the problem more by causing BUG_ON() to trigger (which
this patch turns into a WARN_ON instead).
We need to be careful when using a variant of low power state that
has the side effect of turning interrupts back on, to properly set
all the SW & lazy state to look as if everything is enabled before
we enter the low power state with MSR:EE off as we will return with
MSR:EE on. If not, we have a discrepancy of state which can cause
things to go very wrong later on.
This patch moves the logic into a helper and uses it from the
pseries and cell idle code. The power4/970 idle code already got
things right (in assembly even !) so I'm not touching it. The power7
"bare metal" idle code is subtly different and correct. Remains PA6T
and some hypervisor based Cell platforms which have questionable
code in there, but they are mostly dead platforms so I'll fix them
when I manage to get final answers from the respective maintainers
about how the low power state actually works on them.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@vger.kernel.org [v3.4]
high_width can be easily calculated in a single expression when
making use of __ffs64().
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/4FF71053020000780008E1B5@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With the variable operated on being of "unsigned long" type,
neither ffs() nor fls() are suitable to use on them, as those
truncate their arguments to 32 bits. Using __ffs() and __fls()
respectively at once eliminates the need to subtract 1 from their
results.
Additionally, with the alignment value subsequently used as a
shift count, it must be enforced to be less than BITS_PER_LONG
(and on 64-bit there's no need for it to be any smaller).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/4FF70D54020000780008E179@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit cb8ca5897 (ARM: omap3evm: enable VBUS switch for EHCI tranceiver)
added a new randconfig error if TWL4030_CORE is not selected:
arch/arm/mach-omap2/board-omap3evm.c:368: undefined reference to `twl_i2c_read_u8'
arch/arm/mach-omap2/board-omap3evm.c:370: undefined reference to `twl_i2c_write_u8'
Signed-off-by: Tony Lindgren <tony@atomide.com>
* pci/myron-final-fixups-v2:
PCI: call final fixups hot-added devices
PCI: move final fixups from __init to __devinit
x86/PCI: move final fixups from __init to __devinit
MIPS/PCI: move final fixups from __init to __devinit
PCI: never discard enable/suspend/resume_early/resume fixups
PCI: release temporary reference in __nv_msi_ht_cap_quirk()
PCI: restructure 'pci_do_fixups()'
Final fixups are executed during device enumeration. If we support
hotplug, this may be after boot, so final fixups cannot be __init.
[bhelgaas: changelog]
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Final fixups are executed during device enumeration. If we support
hotplug, this may be after boot, so final fixups cannot be __init.
[bhelgaas: changelog]
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add support for our "aks-cdu" board based up on Telit's module GE863 Pro3.
It has more uarts, leds, another nand partitioning.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
[nicolas.ferre@atmel.com: correction of the dts file]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
OMAP5 has 8 GPIO banks so that there are 32x8 = 256 GPIOs.
In order for the gpiolib to detect and initialize these
additional GPIOs and other TWL GPIOs, ARCH_NR_GPIO is set
to 512 instead of present 256.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Reported-by: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Adding the build support required for OMAP5 soc
in to omap2+ config.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Adding the minimum device tree files required for
OMAP5 to boot.
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Adding the minimal support for OMAP5 evm board
with device tree.
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Move the irq_match arrays and the irq init functions of OMAP 2,3
and 4 based boards out of board-generic.c file and also rename the
irq init function to match the interrupt controller present in
the SOCs.
This is a preparatory patch to add the OMAP5 evm board's irq init
support with device tree.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Add OMAP5 SMP boot support using OMAP4 SMP code. The relevant code paths
are runtime checked using cpu id
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
OMAP4 and OMAP5 share same WakeupGen IP with below few udpates on OMAP5.
- Additional 32 interrupt support is added w.r.t OMAP4 design.
- The AUX CORE boot registers are now made accessible from non-secure SW.
- SAR offset are changed and PTMSYNC* registers are removed from SAR.
Patch updates the WakeupGen code accordingly.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The l3 interconnect ip is same for OMAP4 and OMAP5.
So reuse the l3 error handler error code for OMAP5
as well. Also a few targets has been newly added for
OMAP5. So updating the driver for that here.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
GPMC module is the same as in OMAP4.
Just update the base address and irq number.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Adding the Initialisaton for clocksource and clockevent device
on OMAP5 Socs.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP
architecture. It's a dual core SOC with GIC used for interrupt
handling and with an integrated L2 cache controller.
OMAP5432 is another variant of OMAP5430, with a
memory controller supporting DDR3 and SATA.
Patch includes:
- The machine specific headers and sources updates.
- Platform header updates.
- Minimum initialisation support for serial.
- IO table init
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Adding the OMAP5 ES1.0, 2.0 and OMAP5432 cpu revision
detection support.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
OMAP socs has a legacy and a highlander version of the
32k sync counter IP. The register offsets vary between the
highlander and the legacy scheme. So use the 'SCHEME'
bits(30-31) of the revision register to distinguish between
the two versions and choose the CR register offset accordingly.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
omap_secure_ram_reserve_memblock is stubbed for OMAP1,2 only builds using a
ifdef check. But this results in adding CONFIG_ARCH_OMAPxx checks for
future socs that use the real function. So move this to common.c file and
call it __weak.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The 4430 and 4460 version of PandaBoard mostly the same with
exception at least in audio setup.
Use the omap4-panda.dts file as a base and only override the differences
between the revisions.
For audio it is the name of the sound card and the routing information.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
PandaBoard uses twl6040 connected via McPDM for audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP4 SDP the audio setup includes the twl6040 codec and digital
microphones.
Since OMAP4 SDP is a reference board it has all possible audio interfaces
connected. This information is passed via the ti,audio-routing
property.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The twl6040 provides the audio and vibra support on OMAP4 SDP boards.
It is connected to i2c1 bus with 0x4b address.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DMIC IP is used to connect up to 6 digital microphones directly to OMAP.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McPDM is used on OMAP4 based boards to communicate with an external audio
codec (twl6040).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sys_nirq2 is used for twl6040, make sure the pin is configured
correctly.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sys_nirq2 is used for twl6040, make sure the pin is configured
correctly.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Our emulation should be complete enough that we can emulate guests
while they are in big real mode, or in a mode transition that is not
virtualizable without unrestricted guest support.
Signed-off-by: Avi Kivity <avi@redhat.com>
Guest software doesn't actually depend on it, but vmx will refuse us
entry if we don't. Set the bit in both the cached segment and memory,
just to be nice.
Signed-off-by: Avi Kivity <avi@redhat.com>
Opcode C8.
Only ENTER with lexical nesting depth 0 is implemented, since others are
very rare. We'll fail emulation if nonzero lexical depth is used so data
is not corrupted.
Signed-off-by: Avi Kivity <avi@redhat.com>
Commit 2adb5ad9fe removed ByteOp from MOVZX/MOVSX, replacing them by
SrcMem8, but neglected to fix the dependency in the emulation code
on ByteOp. This caused the instruction not to have any effect in
some circumstances.
Fix by replacing the check for ByteOp with the equivalent src.op_bytes == 1.
Signed-off-by: Avi Kivity <avi@redhat.com>
If we return early from an invalid guest state emulation loop, make
sure we return to it later if the guest state is still invalid.
Signed-off-by: Avi Kivity <avi@redhat.com>
Checking EFLAGS.IF is incorrect as we might be in interrupt shadow. If
that is the case, the main loop will notice that and not inject the interrupt,
causing an endless loop.
Fix by using vmx_interrupt_allowed() to check if we can inject an interrupt
instead.
Signed-off-by: Avi Kivity <avi@redhat.com>
We correctly default to SS when BP is used as a base in 16-bit address mode,
but we don't do that for 32-bit mode.
Fix by adjusting the default to SS when either ESP or EBP is used as the base
register.
Signed-off-by: Avi Kivity <avi@redhat.com>
memop is not initialized; this can lead to a two-byte operation
following a 4-byte operation to see garbage values. Usually
truncation fixes things fot us later on, but at least in one case
(call abs) it doesn't.
Fix by moving memop to the auto-initialized field area.
Signed-off-by: Avi Kivity <avi@redhat.com>
Otherwise, if the guest ends up looping, we never exit the srcu critical
section, which causes synchronize_srcu() to hang.
Signed-off-by: Avi Kivity <avi@redhat.com>
Some userspace (e.g. QEMU 1.1) munge the d and g bits of segment
descriptors, causing us not to recognize them as unusable segments
with emulate_invalid_guest_state=1. Relax the check by testing for
segment not present (a non-present segment cannot be usable).
Signed-off-by: Avi Kivity <avi@redhat.com>
The operand size for these instructions is 8 bytes in long mode, even without
a REX prefix. Set it explicitly.
Triggered while booting Linux with emulate_invalid_guest_state=1.
Signed-off-by: Avi Kivity <avi@redhat.com>
Opcode 0F A2.
Used by Linux during the mode change trampoline while in a state that is
not virtualizable on vmx without unrestricted_guest, so we need to emulate
it is emulate_invalid_guest_state=1.
Signed-off-by: Avi Kivity <avi@redhat.com>
Instead of getting an exact leaf, follow the spec and fall back to the last
main leaf instead. This lets us easily emulate the cpuid instruction in the
emulator.
Signed-off-by: Avi Kivity <avi@redhat.com>
Introduce kvm_cpuid() to perform the leaf limit check and calculate
register values, and let kvm_emulate_cpuid() just handle reading and
writing the registers from/to the vcpu. This allows us to reuse
kvm_cpuid() in a context where directly reading and writing registers
is not desired.
Signed-off-by: Avi Kivity <avi@redhat.com>
In protected mode, the CPL is defined as the lower two bits of CS, as set by
the last far jump. But during the transition to protected mode, there is no
last far jump, so we need to return zero (the inherited real mode CPL).
Fix by reading CPL from the cache during the transition. This isn't 100%
correct since we don't set the CPL cache on a far jump, but since protected
mode transition will always jump to a segment with RPL=0, it will always
work.
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently the MMU's ->new_cr3() callback does nothing when guest paging
is disabled or when two-dimentional paging (e.g. EPT on Intel) is active.
This means that an emulated write to cr3 can be lost; kvm_set_cr3() will
write vcpu-arch.cr3, but the GUEST_CR3 field in the VMCS will retain its
old value and this is what the guest sees.
This bug did not have any effect until now because:
- with unrestricted guest, or with svm, we never emulate a mov cr3 instruction
- without unrestricted guest, and with paging enabled, we also never emulate a
mov cr3 instruction
- without unrestricted guest, but with paging disabled, the guest's cr3 is
ignored until the guest enables paging; at this point the value from arch.cr3
is loaded correctly my the mov cr0 instruction which turns on paging
However, the patchset that enables big real mode causes us to emulate mov cr3
instructions in protected mode sometimes (when guest state is not virtualizable
by vmx); this mov cr3 is effectively ignored and will crash the guest.
The fix is to make nonpaging_new_cr3() call mmu_free_roots() to force a cr3
reload. This is awkward because now all the new_cr3 callbacks to the same
thing, and because mmu_free_roots() is somewhat of an overkill; but fixing
that is more complicated and will be done after this minimal fix.
Observed in the Window XP 32-bit installer while bringing up secondary vcpus.
Signed-off-by: Avi Kivity <avi@redhat.com>
CP_INTC code in entry-macro.S code reads SECR1n register to see if
an interrupt was indeed pending. This register is actually marked as
write-only in the OMAP-L138 TRM. Moreover, the code just checks to see
the entire register is non-zero and does not check a specific interrupt
number.
Fix this to use interrupt pending bit in GIPR register for this purpose.
GIPR register is already being read to know the highest priority interrupt
pending.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The MMC/SD and SPI entries in this file are not tested yet. They
inadvertently came into the patch because of some work in progress
stuff I had in my repo.
These entries should not have been sent out in the first place and
I am sorry for the trouble and will be extra careful in future.
Since the offending commit is not sent upstream yet, I hope this can
be merged into the commit 5fc0b42a98
(arm/dts: Add initial DT support for AM33XX SoC family) on the devel-dt
branch of linux-omap tree.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If provided dt support, then skip add wdt platform device as usual.
Signed-off-by: Xiao Jiang <jgq516@gmail.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 only build breaks with below error
arch/arm/mach-omap2/sdrc.c:135: error: redefinition of 'omap2_sdrc_init'
arch/arm/plat-omap/include/plat/sdrc.h:130: note: previous definition of 'omap2_sdrc_init' was here
make[1]: *** [arch/arm/mach-omap2/sdrc.o] Error 1
Fix the same by using newly introduced CONFIG_SOC_HAS_OMAP2_SDRC marco.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch completes commit 08406f5 by fixing the following issues, according to
the reference manual:
* MXC_OTG_UCTRL_OPM_BIT disables (masks) the power/oc pins if set, like H1PM and
H2PM, not the opposite.
* MXC_OTG_PHYCTRL_OC_DIS_BIT disables the oc pin if set, like H1_OC_DIS, not the
opposite.
* Typos in comments.
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Make ehci power and overcurrent polarities configurable. If not set, these new
configurartions keep the default register values so that existing board files
do not have to be changed.
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Now that RTC support has been enabled for i.MX35, add RTC to the mx35_3ds board.
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX35 has an RTC compatible with the i.MX31's, so enable its support even
if it's not very useful because it's not battery backed.
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The data sheet of the i.MX35 says it is an ARM1136JF-S processor, version r1p3,
which, according to section "B.1. New instructions" of the ARM1136JF-S and
ARM1136J-S Technical Reference Manual, makes the i.MX35 CPU architecture not
only ARMv6, but ARMv6k.
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds missing definitions for DISP, GPT and CCM pads.
These pins are not used by kernel, but may be helpful for custom boards.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add a very basic dt support for mx27_3ds (also known as mx27pdk).
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The EHCI driver is not stable enough to be enabled by default. In v3.5,
it has at least the following problems:
- warning dump during bootup
- hang during suspend
- prevents CORE powerdomain from entering retention during idle (even
when no USB devices connected.)
This demonstrates that this driver has not been thoroughly tested and
therfore should not be enabled in the default defconfig.
In addition, the problems above cause new PM regressions which need be
addressed before this driver should be enabled in the default
defconfig.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Prior to the new i.mx clock conversion the mx27 silicon version was printed at boot.
Reenable this feature.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Pull ARM fixes from Russell King:
"Last merge window, we had some updates from Al cleaning up the signal
restart handling. These have caused some problems on ARM, and while
Al has some fixes, we have some concerns with Al's patches but we've
been unsuccesful with discussing this.
We have got to the point where we need to do something, and we've
decided that the best solution is to revert the appropriate commits
until Al is able to reply to us.
Also included here are four patches to fix warnings that I've noticed
in my build system, and one fix for kprobes test code."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: fix warning caused by wrongly typed arm_dma_limit
ARM: fix warnings about atomic64_read
ARM: 7440/1: kprobes: only test 'sub pc, pc, #1b-2b+8-2' on ARMv6
ARM: 7441/1: perf: return -EOPNOTSUPP if requested mode exclusion is unavailable
ARM: 7443/1: Revert "new way of handling ERESTART_RESTARTBLOCK"
ARM: 7442/1: Revert "remove unused restart trampoline"
ARM: fix set_domain() macro
ARM: fix mach-versatile/pci.c warning
Change the value of #interrupt-cells of gpio nodes from 1 to 2, so that
the gpio irq type can be specified in device tree. Also update binding
document to make it clear.
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This change adds macros for routing of GIC interrupts for EIC and
non-EIC hardware modes. Also added Malta GIC macros having to do
with performance and timer interrupts.
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3576/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Based on https://patchwork.linux-mips.org/patch/3576 - but this really
deserves its own patchset and the symbol should also be used :)
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
From Stephen Warren <swarren@wwwdotorg.org>:
This branch contains a single commit which adjusts tegra_defconfig to
enable new kernel features, driven by new device tree file content and drivers.
* 'for-3.6/defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: defconfig updates
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Stephen Warren <swarren@wwwdotorg.org>:
This branch contains numerous changes required as a baseline in order to
convert Tegra to the common clock framework. The intention was to also
include patches to actually convert Tegra to the common clock framework.
However, those patches appeared late in the kernel cycle and currently
cause regressions on some boards, so were dropped for now.
* 'for-3.6/common-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: Provide clock for only one PWM controller
ARM: tegra: Fix PWM clock programming
ARM: tegra: dma: rename driver name for clock to "tegra-apbdma"
ARM: tegra: Remove second instance of uart clk
crypto: add clk_prepare/clk_unprepare
ASoC: tegra: add clk_prepare/clk_unprepare
staging: nvec: add clk_prepare/clk_unprepare
spi/tegra: add clk_prepare/clk_unprepare
Input: tegra-kbc - add clk_prepare/clk_unprepare
USB: ehci-tegra: add clk_prepare/clk_unprepare
mmc: tegra: add clk_prepare/clk_unprepare
i2c: tegra: Add clk_prepare/clk_unprepare
ARM: tegra: add clk_prepare/clk_unprepare
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Stephen Warren <swarren@wwwdotorg.org>
This branch contains changes to Tegra board files, and related Kconfig and
Makefile changes. Highlights include:
* Removal of Seaboard/Springbank board files; these boards can now only be
used with device tree.
* Use of small parts of some non-DT board files from the DT board files. This
enables all features that the non-DT board files have, when booting from DT.
This will allow almost complete removal of all non-DT board files in v3.7.
* Other miscellaneous changes.
This branch is based on Tegra's for-3.6/cleanup branch from a previous pull
request.
* 'for-3.6/boards' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: use of_default_bus_match_table
ARM: tegra: add device tree AUXDATA for APBDMA
ARM: tegra: paz00: enable WiFi rfkill when booting from device tree
ARM: tegra: harmony: init regulators, PCIe when booting from DT
ARM: tegra: trimslice: enable PCIe when booting from device tree
ARM: tegra: remove Seaboard board files
ARM: tegra: remove CONFIG_MACH_TEGRA_DT
ARM: tegra: make .dts compilation depend on Tegra2 support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Stephen Warren <swarren@wwwdotorg.org>:
This branch contains changes to Tegra SoC-specific code in the
mach-tegra directory; only APBIO/DMA-related patches this time around.
* 'for-3.6/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: apbio: use dmaengine based dma driver
ARM: tegra: apbio access using dma for tegra20 only
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix build error in the case of SMP=y but ARCH_SH73A0=n
introduced by:
9601e87 ARM: shmobile: fix smp build
The use of of_machine_is_compatible() will link in the
the SoC-specific symbols:
"sh73a0_get_core_count", "sh73a0_smp_prepare_cpus",
"sh73a0_secondary_init" and "sh73a0_boot_secondary".
This patch adds an ugly #ifdef wrapper as a stop-gap
solution.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Lee Jones <lee.jones@linaro.org>:
* ux500/fixes-3.5:
ARM: ux500: Over-ride the DT device naming scheme for pinctrl
ARM: ux500: Fix build errors/warnings when MACH_UX500_DT is not set
of: address: Don't fail a lookup just because a node has no reg property
I ended up rebasing Lee's branch on 3.5-rc5 because we have more patches
lined for 3.6 that depend on them, and I want to keep all branches in
arm-soc be based on -rc releases rather than random commits in the
upstream history.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When pin control mapping tables are written the registered device
name is supplied for use in name-based searches within the pinctrl
driver. In the case of the DB8500 the string "pinctrl-db8500" is
used. However, when we register the driver with Device Tree, its
naming convention uses something that looks more like "pinctrl.2".
To work around the device naming inconsistencies between devices
registered via platform code and the ones registered by Device
Tree, we use AUXDATA to over-ride the Device Tree naming scheme.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When MACH_UX500_DT and all related Device Tree configurations are forced
off the warning and error below prevent the kernel from compiling. This
simple patch fixes both issues and allows for full build and boot of
ST-Ericsson's low-cost development board, Snowball.
Warnings fixed:
arch/arm/mach-ux500/board-mop500.c:680:32: warning: ‘snowball_of_platform_devs’ defined but not used
Errors fixed:
arch/arm/mach-ux500/timer.c: In function ‘ux500_timer_init’:
arch/arm/mach-ux500/timer.c:66:3: error: implicit declaration of function ‘of_find_matching_node’
arch/arm/mach-ux500/timer.c:66:6: warning: assignment makes pointer from integer without a cast
Cc: stable@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Two bug fixes for the previous state of the imx sparse irq changes.
* 'imx/sparse-irq' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: select USE_OF
ARM: imx: Fix build error due to missing irqs.h include
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Shawn Guo <shawn.guo@linaro.org>:
* 'mxs/defconfig-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: defconfig: Enable CONFIG_COMMON_CLK_DEBUG
ARM: mxs_defconfig: Enable RTC driver
ARM: mxs_defconfig: Let AUART driver be built by default
ARM: mxs: Enable MACH_APX4DEVKIT
ARM: mxs: Let GPMI driver be built by default
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tegra's I2C2 controller can be routed to either the PTA or DDC pin group
on Seaboard. Define the pinctrl state nodes required to allow runtime
control of this routing. Instantiate a pinctrl-i2cmux I2C bus mux that
uses these pinctrl states.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Whistler is a highly configurable Tegra evaluation and development board.
This change adds support for the following specific configuration:
E1120 motherboard
E1108 CPU board
E1116 PMU board
The motherboard configuration switches are set as follows:
SW1=0 SW2=0 SW3=5
S1/S2/S3/S4 all on, except S3 7/8 are off.
Other combinations of daugher boards may work to varying degrees, but will
likely require some SW adjustment.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use the dmaengine based Tegra APB DMA driver for
apbio access in place of legacy Tegra APB DMA.
The new driver is selected if legacy driver is not
selected and new DMA driver is enabled through config
file.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: s/pr_err/pr_debug/ in tegra_apb_dma_init; this condition is
expected to fire repeatedly before the DMA driver is available]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tegra20 HW issue with accessing APBIO registers (such
as fuse registers) directly from the CPU concurrently with
APB DMA accesses has been fixed in Tegra30 and later chips.
Access these registers directly from the CPU on Tegra30
and later, and apply the workaround only for Tegra20.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Chaitanya Bandi <bandik@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The pattern (np ? np->full_name : "<none>") is rather common in the
kernel, but can also make for quite long lines. This patch adds a new
inline function, of_node_full_name() so that the test for a valid node
pointer doesn't need to be open coded at all call sites.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Use tabs for "intel_perfmon_event_map" formatting in
perf_event_intel.c.
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Link: http://lkml.kernel.org/r/1341568786-7045-1-git-send-email-penberg@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
During boot or driver load etc, interrupt destination is setup
using default target cpu's. Later the user (irqbalance etc) or
the driver (irq_set_affinity/ irq_set_affinity_hint) can request
the interrupt to be migrated to some specific set of cpu's.
In the x2apic cluster routing, for the default scenario use
single cpu as the interrupt destination and when there is an
explicit interrupt affinity request, route the interrupt to
multiple members of a x2apic cluster specified in the cpumask of
the migration request.
This will minmize the vector pressure when there are lot of
interrupt sources and relatively few x2apic clusters (for
example a single socket server). This will allow the performance
critical interrupts to be routed to multiple cpu's in the x2apic
cluster (irqbalance for example uses the cache siblings etc
while specifying the interrupt destination) and allow
non-critical interrupts to be serviced by a single logical cpu.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Link: http://lkml.kernel.org/r/1340656709-11423-4-git-send-email-suresh.b.siddha@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For the x2apic cluster mode, vector for an interrupt is
currently reserved on all the cpu's that are part of the x2apic
cluster. But the interrupts will be routed only to the cluster
(derived from the first cpu in the mask) members specified in
the mask. So there is no need to reserve the vector in the
unused cluster members.
Modify __assign_irq_vector() to reserve the vectors based on the
user specified irq destination mask. If the new mask is a proper
subset of the currently used mask, cleanup the vector allocation
on the unused cpu members.
Also, allow the apic driver to tune the vector domain based on
the affinity mask (which in most cases is the user-specified
mask).
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Link: http://lkml.kernel.org/r/1340656709-11423-3-git-send-email-suresh.b.siddha@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently __assign_irq_vector() goes through each cpu in the
specified mask until it finds a free vector in all the cpu's
that are part of the same interrupt domain. We visit all the
interrupt domain sibling cpus to reserve the free vector. So,
when we fail to find a free vector in an interrupt domain, it is
safe to continue our search with a cpu belonging to a new
interrupt domain. No need to go through each cpu, if the domain
containing that cpu is already visited.
Use the irq_cfg's old_domain to track the visited domains and
optimize the cpu traversal while finding a free vector in the
given cpumask.
NOTE: We can also optimize the search by using for_each_cpu() and
skip the current cpu, if it is not the first cpu in the mask
returned by the vector_allocation_domain(). But re-using the
cfg->old_domain to track the visited domains will be slightly
faster.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Link: http://lkml.kernel.org/r/1340656709-11423-2-git-send-email-suresh.b.siddha@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently most ads7846 config definitions for OMAP3 series boards have
been moved to common-board-devices.c, and it is transparent for init.
And it's no very proper to do gpio_request based on get_pendown_state
since omap_ads7846_init knows everything about ads7846_config.
So it's more fit to request gpio according to the right gpio_pendown
and set debounce time conditionally. If we don't set proper debouce
time, there are flooded interrupt counters of ads7846 responding to
one time touch on screen, then the driver couldn't work very well.
This patch has been validated on 3530evm.
Signed-off-by: Zumeng Chen <zumeng.chen@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This was chosen by following the trace on the schematic from component U131
and U134 to the CPEN pin on the USB3320 device.
TWL4030.GPIO2-...->(T2_GPIO2_3V3)U131-..>nUSB2_EN-..>U134-..>EXP_nUSB2_1V8
which starts EHCI tranceiver USB3320.
This will set TWL4030.GPIO2 as output pin to drive EHCI tranceiver.
Signed-off-by: Zumeng Chen <zumeng.chen@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
EHCI PHY requires these regulators:
EVM Rev >=E --> VAUX2
EVM Rev < E --> VUSB1V5, VUSB1V8
Adding USB internal LDOs (vusb1v5 & vusb1v8) and VAUX2 to omap3evm
board file. Also removing vaux2_{1/2/3} supplies as they are not
used on omap3 evm.
But we need not to add vaux2 in twl4030_platform_data since it will
be added conditionally.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Zumeng Chen <zumeng.chen@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With omap_hwmod_get_main_clk() now available, this can be passed to
clk_get() to extract the fclk and thus avoid construction of fclk name.
Corrected the timer fck name mis-match between clock44xx_data.c and
omap_hwmod_44xx_data.c. For other platforms this is already taken care.
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit ac5b0ea3d (Merge tag 'omap-devel-f-for-3.6'...) had a merge
conflict that somehow got incorrecly resolved in a lossy way for
commit bed9d1bb (ARM: OMAP2+: hwmod: add omap_hwmod_get_main_clk() API).
Fix the issue by applying the missing pieces.
Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit
544496a (ARM: imx: move irq_domain_add_legacy call into avic driver)
introduced unconditional calls to irq_find_mapping and
irq_domain_add_legacy, but it's still possible to have a .config without
CONFIG_IRQ_DOMAIN=y resulting in
CC arch/arm/plat-mxc/avic.o
arch/arm/plat-mxc/avic.c: In function 'avic_handle_irq':
arch/arm/plat-mxc/avic.c:172: error: implicit declaration of function 'irq_find_mapping'
arch/arm/plat-mxc/avic.c: In function 'mxc_init_irq':
arch/arm/plat-mxc/avic.c:207: error: implicit declaration of function 'irq_domain_add_legacy'
arch/arm/plat-mxc/avic.c:208: error: 'irq_domain_simple_ops' undeclared (first use in this function)
arch/arm/plat-mxc/avic.c:208: error: (Each undeclared identifier is reported only once
arch/arm/plat-mxc/avic.c:208: error: for each function it appears in.)
arch/arm/plat-mxc/avic.c:208: warning: assignment makes pointer from integer without a cast
make[3]: *** [arch/arm/plat-mxc/avic.o] Error 1
make[2]: *** [arch/arm/plat-mxc/avic.o] Error 2
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
While selecting CONFIG_IRQ_DOMAIN would be enough, USE_OF is the future
and implies CONFIG_IRQ_DOMAIN. So select USE_OF for ARCH_MXC and drop
other explicit selects that are superflous now.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
With the common clock framework in place, it is useful to enable
CONFIG_COMMON_CLK_DEBUG option, in order to easily inspect the clock tree.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Kevin discovered that commit c8d82ff68f
("ARM: OMAP2/3: hwmod data: Add 32k-sync timer data to hwmod
database") broke CORE idle on OMAP3. This prevents device low power
states.
The root cause is that the 32K sync timer IP block does not support
smart-idle mode[1], and so the hwmod code keeps the IP block in
no-idle mode while it is active. This in turn prevents the WKUP
clockdomain from transitioning to idle. There is a hardcoded sleep
dependency that prevents the CORE_L3 and CORE_CM clockdomains from
transitioning to idle when the WKUP clockdomain is active[2], so the
chip cannot enter any device low power states.
It turns out that there is no need to take the 32k sync timer out of
idle. The IP block itself probably does not have any native idle
handling at all, due to its simplicity. Furthermore, the PRCM will
never request target idle for this IP block while the kernel is
running, due to the sleep dependency that prevents the WKUP
clockdomain from idling while the CORE_L3 clockdomain is active. So
we can safely leave the 32k sync timer in target-force-idle mode, even
while we continue to access it.
This workaround is implemented by defining a new clockdomain flag,
CLKDM_ACTIVE_WITH_MPU, that indicates that the clockdomain is
guaranteed to be active whenever the MPU is inactive. If an IP
block's main functional clock exists inside this clockdomain, and the
IP block does not support smart-idle modes, then the hwmod code will
place the IP block into target force-idle mode even when enabled. The
WKUP clockdomains on OMAP3/4 are marked with this flag. (On OMAP2xxx,
no OCP header existed on the 32k sync timer.) Other clockdomains also
should be marked with this flag, but those changes are deferred until
a later merge window, to create a minimal fix.
Another theoretically clean fix for this problem would be to implement
PM runtime-based control for 32k sync timer accesses. These PM
runtime calls would need to located in a custom clocksource, since the
32k sync timer is currently used as an MMIO clocksource. But in
practice, there would be little benefit to doing so; and there would
be some cost, due to the addition of unnecessary lines of code and the
additional CPU overhead of the PM runtime and hwmod code - unnecessary
in this case.
Another possible fix would have been to modify the pm34xx.c code to
force the IP block idle before entering WFI. But this would not have
been an acceptable approach: we are trying to remove this type of
centralized IP block idle control from the PM code.
This patch is a collaboration between Kevin Hilman <khilman@ti.com>
and Paul Walmsley <paul@pwsan.com>.
Thanks to Vaibhav Hiremath <hvaibhav@ti.com> for providing comments on
an earlier version of this patch. Thanks to Tero Kristo
<t-kristo@ti.com> for identifying a bug in an earlier version of this
patch. Thanks to Benoît Cousson <b-cousson@ti.com> for identifying
some bugs in several versions of this patch and for implementation
comments.
References:
1. Table 16-96 "REG_32KSYNCNT_SYSCONFIG" of the OMAP34xx TRM Rev. ZU
(SWPU223U), available from:
http://www.ti.com/pdfs/wtbu/OMAP34x_ES3.1.x_PUBLIC_TRM_vzU.zip
2. Table 4-72 "Sleep Dependencies" of the OMAP34xx TRM Rev. ZU
(SWPU223U)
3. ibid.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
* pci/myron-pcibios_setup:
xtensa/PCI: factor out pcibios_setup()
x86/PCI: adjust section annotations for pcibios_setup()
unicore32/PCI: adjust section annotations for pcibios_setup()
tile/PCI: factor out pcibios_setup()
sparc/PCI: factor out pcibios_setup()
sh/PCI: adjust section annotations for pcibios_setup()
sh/PCI: factor out pcibios_setup()
powerpc/PCI: factor out pcibios_setup()
parisc/PCI: factor out pcibios_setup()
MIPS/PCI: adjust section annotations for pcibios_setup()
MIPS/PCI: factor out pcibios_setup()
microblaze/PCI: factor out pcibios_setup()
ia64/PCI: factor out pcibios_setup()
cris/PCI: factor out pcibios_setup()
alpha/PCI: factor out pcibios_setup()
PCI: pull pcibios_setup() up into core
The PCI core provides a generic pcibios_setup() routine. Drop this
architecture-specific version in favor of that.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI core provides a generic pcibios_setup() routine. Drop this
architecture-specific version in favor of that.
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI core provides a generic pcibios_setup() routine. Drop this
architecture-specific version in favor of that.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI core provides a generic pcibios_setup() routine. Drop this
architecture-specific version in favor of that.
Tested-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI core provides a generic pcibios_setup() routine. Drop this
architecture-specific version in favor of that.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI core provides a generic pcibios_setup() routine. Drop this
architecture-specific version in favor of that.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI core provides a generic pcibios_setup() routine. Drop this
architecture-specific version in favor of that.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI core provides a generic pcibios_setup() routine. Drop this
architecture-specific version in favor of that.
Acked-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI core provides a generic pcibios_setup() routine. Drop this
architecture-specific version in favor of that.
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI core provides a generic pcibios_setup() routine. Drop this
architecture-specific version in favor of that.
This patch fixes what looks like a bug in cris, which implements
pcibios_setup() such that pci_setup() doesn't look for any generic
options.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Small fixes on multiple ARM platforms
* A build regression from a previous fix on dove and mv78xx0
* Two fixes for recently (3.5-rc1) changed mmp/pxa code
* multiple omap2+ bug fixes
* two trivial fixes for i.MX
* one v3.5 regression for mxs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=2Ynd
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Small fixes on multiple ARM platforms
- A build regression from a previous fix on dove and mv78xx0
- Two fixes for recently (3.5-rc1) changed mmp/pxa code
- multiple omap2+ bug fixes
- two trivial fixes for i.MX
- one v3.5 regression for mxs"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: apx4devkit: fix FEC enabling PHY clock
ARM: OMAP2+: hwmod data: Fix wrong McBSP clock alias on OMAP4
ARM: OMAP4: hwmod data: temporarily comment out data for the usb_host_fs and aess IP blocks
ARM: Orion: Fix WDT compile for Dove and MV78xx0
ARM: mmp: remove mach/gpio-pxa.h
ARM: imx: assert SCC gate stays enabled
ARM: OMAP4: TWL6030: ensure sys_nirq1 is mux'd and wakeup enabled
ARM: OMAP2: Overo: init I2C before MMC to fix MMC suspend/resume failure
ARM: imx27_visstrim_m10: Do not include <asm/system.h>
ARM: pxa: hx4700: Fix basic suspend/resume
Pull KVM fix from Marcelo Tosatti:
"Memory leak and oops on the x86 mmu code, and sanitization of the
KVM_IRQFD ioctl."
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: MMU: fix shrinking page from the empty mmu
KVM: fix fault page leak
KVM: Sanitize KVM_IRQFD flags
KVM: Add missing KVM_IRQFD API documentation
KVM: Pass kvm_irqfd to functions
This patch adds C-Box and PCU filter support for SandyBridge-EP
uncore. We can filter C-Box events by thread/core ID and filter
PCU events by frequency/voltage.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1341381616-12229-5-git-send-email-zheng.z.yan@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The CBox manages the interface between the core and the LLC, so
the instances of uncore CBox is equal to number of cores.
Reported-by: Andrew Cooks <acooks@gmail.com>
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1341381616-12229-4-git-send-email-zheng.z.yan@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Stephane Eranian suggestted using 0xff as pseudo code for fixed
uncore event and using the umask value to determine which of the
fixed events we want to map to. So far there is at most one fixed
counter in a uncore PMU. So just change the definition of
UNCORE_FIXED_EVENT to 0xff.
Suggested-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1340780953-21130-1-git-send-email-zheng.z.yan@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
All these are basically boolean flags, use a bitfield to save a few
bytes.
Suggested-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-vsevd5g8lhcn129n3s7trl7r@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Recent Intel microcode resolved the SNB-PEBS issues, so conditionally
enable PEBS on SNB hardware depending on the microcode revision.
Thanks to Stephane for figuring out the various microcode revisions.
Suggested-by: Stephane Eranian <eranian@google.com>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-v3672ziwh9damwqwh1uz3krm@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It might be of interest which perfctr msr failed.
Signed-off-by: Robert Richter <robert.richter@amd.com>
[ added hunk to avoid GCC warn ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1340217996-2254-5-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There is no need for keeping separate pmu structs. We can enable
amd_{get,put}_event_constraints() functions also for family 15h event.
The advantage is that there is only a single pmu struct for all AMD
cpus. This patch introduces functions to setup the pmu to enabe core
performance counters or counter constraints.
Also, cpuid checks are used instead of family checks where
possible. Thus, it enables the code independently of cpu families if
the feature flag is set.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1340217996-2254-4-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There is some Intel specific code in the generic x86 path. Move it to
intel_pmu_init().
Since p4 and p6 pmus don't have fixed counters we may skip the check
in case such a pmu is detected.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1340217996-2254-3-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There are macros that are Intel specific and not x86 generic. Rename
them into INTEL_*.
This patch removes X86_PMC_IDX_GENERIC and does:
$ sed -i -e 's/X86_PMC_MAX_/INTEL_PMC_MAX_/g' \
arch/x86/include/asm/kvm_host.h \
arch/x86/include/asm/perf_event.h \
arch/x86/kernel/cpu/perf_event.c \
arch/x86/kernel/cpu/perf_event_p4.c \
arch/x86/kvm/pmu.c
$ sed -i -e 's/X86_PMC_IDX_FIXED/INTEL_PMC_IDX_FIXED/g' \
arch/x86/include/asm/perf_event.h \
arch/x86/kernel/cpu/perf_event.c \
arch/x86/kernel/cpu/perf_event_intel.c \
arch/x86/kernel/cpu/perf_event_intel_ds.c \
arch/x86/kvm/pmu.c
$ sed -i -e 's/X86_PMC_MSK_/INTEL_PMC_MSK_/g' \
arch/x86/include/asm/perf_event.h \
arch/x86/kernel/cpu/perf_event.c
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1340217996-2254-2-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Merge this branch because we want to rely on the newer (and saner)
microcode loading and checking facilities.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Several perf interrupt handlers (PEBS,IBS,BTS) re-write regs->ip but
do not update the segment registers. So use an regs->ip based test
instead of an regs->cs/regs->flags based test.
Reported-and-tested-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/n/tip-xxrt0a1zronm1sm36obwc2vy@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The function __omap2_set_globals() can be common across all
platforms/architectures, even in case of omap4, internally it
calls same set of functions as in __omap2_set_globals() function
(except for sdrc).
This patch adds new config flag SOC_HAS_OMAP2_SDRC to handle sdrc,
so that we can reuse same function across omap2/3/4...
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per recent discussion on the linux-omap list, we are
moving in the direction where, we will have only architecture,
ARCH_OMAP2PLUS and all devices/platforms will be treated
as a SoC underneath.
So the first step in this direction is to adopt this change
for all new devices getting in, converting
cpu_is_am33xx/335x() ==> soc_is_am33xx/335x()
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initially, we decided to make am33xx family of device to fall
under omap3 class (cpu_is_omap34xx() = true), since it carries
Cortex-A8 core. But while adding complete baseport support
(like, clock, power and hwmod) support, it is observed that,
we are creating more and more problems by treating am33xx device
as omap3 family, as nothing matches between them
(except cortex-A8 mpu).
So, after long discussion we have came to the conclusion that,
we should not consider am33xx device as omap3 family, instead
create separate class (SOC_AM33XX) under OMAP2PLUS.
This means, for am33xx device, cpu_is_omap34xx() will return false,
and only cpu_is_am33xx() will be true.
Please refer to the link below, for mailing-list discussion on this -
http://www.spinics.net/lists/linux-omap/msg69439.html
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: fixed typo, updated for soc_is changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to remove unnecessary idefs, move noncore and core
dpll ops to dpll3xxx.c file (where it should have been already).
The clkops (clkops_omap3_core_dpll_ops & clkops_omap3_noncore_dpll_ops)
is used in clock data files, and dependency is already handled by
Makefile rule.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All OMAP2PLUS based devices, builds omap-device.o target;
so just add one entry so that there is no need to patch this file
for any future OMAP2+ devices.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes two checks for valid gpio number, formerly (wrongly)
considering zero as invalid, now using gpio_is_valid().
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
arch/arm/mm/init.c: In function 'arm_memblock_init':
arch/arm/mm/init.c:380: warning: comparison of distinct pointer types lacks a cast
by fixing the typecast in its definition when DMA_ZONE is disabled.
This was missed in 4986e5c7c (ARM: mm: fix type of the arm_dma_limit
global variable).
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix:
net/netfilter/xt_connbytes.c: In function 'connbytes_mt':
net/netfilter/xt_connbytes.c:43: warning: passing argument 1 of 'atomic64_read' discards qualifiers from pointer target type
...
by adding the missing const.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
'sub pc, pc, #1b-2b+8-2' results in address<1:0> == '10'.
sub pc, pc, #const (== ADR pc, #const) performs an interworking branch
(BXWritePC()) on ARMv7+ and a simple branch (BranchWritePC()) on earlier
versions.
In ARM state, BXWritePC() is UNPREDICTABLE when address<1:0> == '10'.
In ARM state on ARMv6+, BranchWritePC() ignores address<1:0>. Before
ARMv6, BranchWritePC() is UNPREDICTABLE if address<1:0> != '00'
So the instruction is UNPREDICTABLE both before and after v6.
Acked-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
working again.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=9LmJ
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-for-v3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
PM related fixes for omaps mostly to get suspend/resume
working again.
* tag 'omap-fixes-for-v3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: hwmod data: Fix wrong McBSP clock alias on OMAP4
ARM: OMAP4: hwmod data: temporarily comment out data for the usb_host_fs and aess IP blocks
ARM: OMAP4: TWL6030: ensure sys_nirq1 is mux'd and wakeup enabled
ARM: OMAP2: Overo: init I2C before MMC to fix MMC suspend/resume failure
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Replace the regular kzalloc and ioremap with the devm_ equivalent
to simplify error handling. We don't need kree() any more in
omap_dm_timer_remove().
Also added *dev* pointer to reference pdev->dev which makes the
usage shorter in code.
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
for 3.6. Mostly small infrastructure improvements, and preparation
for OMAP5 and AM33xx code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJP9F5FAAoJEMePsQ0LvSpLocAP/00cPRZ+sOrZO6KYjoh84AwB
mMfJd2QKhqwe19nBfPoGL3F+bClM5x9yIgX2pT2X46kJ25DqLcIDUnUeKydo/euF
qON+8n2E2Z24iaiLnQvSLYyIJokTX+81l+RmddGYkT2Go8KT6U6XRcOnQ1J/kkIC
Z9rkHkMtzL7wAtYUBcZktlEMw8PKzcLAayCSQsPQ4Q757JHONijtJFID24UyQQPQ
azsuL4bxUJ5zhSeVjJRmCE7sFWbTgJ6vztMm/d1bc/TH4X7dFNKwhKIuZsMrAMBf
fzf+lyB/UFX7CCt7oqQs8E3mX0E9B2ijq5WCal4SSLf7piLIIHxIpTT9LGAzO/of
zYhRA3hY4o/HsaDmgsYxHZAPYGZoODosI93bYBVxBW2qZceYZ1j3nUfd0dY+AkCe
Nm0L1TWeBhVG0oX3fP8bqTTxyiMCn4eDUUAUe002oJrsEFkeUb1+lAvTNoibXyns
rQ9uQjbtR53V8nHT62sYcORxKdfUxGoDT3KFp2CHtKf/agjsuUe6JqP0Z3IkeYvT
nmd+vUmO7D4delpbsT4OIt7vzmXCzTr6qB0hZIyXitFqQHlz9bBO4Fdow51CG+0V
PNykHS9tfU7Ioe0bOMm9MhqjicbbxAJOc1Y4bBh8JGsNDsnfIAm9ZjHEjq7td/yz
sZnZqUUrQHSB5EHBW5LU
=sy5d
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-f-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into cleanup-part2
Miscellaneous OMAP clock, hwmod, clockdomain, and powerdomain patches
for 3.6. Mostly small infrastructure improvements, and preparation
for OMAP5 and AM33xx code.
Conflicts:
arch/arm/mach-omap2/omap_hwmod.c
arch/arm/plat-omap/include/plat/omap_hwmod.h
We currently return -EPERM if the user requests mode exclusion that is
not supported by the CPU. This looks pretty confusing from userspace
and is inconsistent with other architectures (ppc, x86).
This patch returns -EOPNOTSUPP instead.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 6b5c8045ec.
Conflicts:
arch/arm/kernel/ptrace.c
The new syscall restarting code can lead to problems if we take an
interrupt in userspace just before restarting the svc instruction. If
a signal is delivered when returning from the interrupt, the
TIF_SYSCALL_RESTARTSYS will remain set and cause any syscalls executed
from the signal handler to be treated as a restart of the previously
interrupted system call. This includes the final sigreturn call, meaning
that we may fail to exit from the signal context. Furthermore, if a
system call made from the signal handler requires a restart via the
restart_block, it is possible to clear the thread flag and fail to
restart the originally interrupted system call.
The right solution to this problem is to perform the restarting in the
kernel, avoiding the possibility of handling a further signal before the
restart is complete. Since we're almost at -rc6, let's revert the new
method for now and aim for in-kernel restarting at a later date.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit fa18484d09.
We need the restart trampoline back so that we can revert a related
problematic patch 6b5c8045ec ("arm: new
way of handling ERESTART_RESTARTBLOCK").
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avoid polluting drivers with a set_domain() macro, which interferes with
structure member names:
drivers/net/wireless/ath/ath9k/dfs_pattern_detector.c:294:33: error: macro "set_domain" passed 2 arguments, but takes just 1
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a function to initialize the Common Platform Interrupt Controller
(cp_intc) from TI used on OMAP-L1x SoCs using a device tree node.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: davinci-linux-open-source@linux.davincidsp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
management and McBSP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GhIQ
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-b-for-3.5rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
A few more OMAP fixes for 3.5-rc. These fix some bugs with power
management and McBSP.
Ethernet stopped to work after mxs clk framework change.
Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
mx23-olinuxino is a low cost board designed by Olimex.
It has the following features:
- Freescale iMX233 ARM926J processor at 454MHz
-64 MB RAM
-SD-card connector
-TV PAL/NTSC video output
-2 USB High Speed Hosts
-Ethernet 100 Mbit
-Stereo Audio Input
-Stereo Headphones Audio Output
More information at:
http://www.olimex.com/dev/imx233-olinuxino-maxi.html
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
arch/arm/mach-versatile/pci.c: In function 'versatile_map_irq':
arch/arm/mach-versatile/pci.c:342: warning: unused variable 'devslot'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The pinctrl code needs GPIOLIB to be enabled, so make
sure that it cannot be built otherwise. This fixes
the prima2_defconfig.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Barry Song <21cnbao@gmail.com>
The commit 503d0ea24d
ARM: OMAP4: hwmod data: Add aliases for McBSP fclk clocks
added a wrong "prcm_clk" alias for PRCM clock whereas the McBSP
driver and previous OMAPs are using "prcm_fck".
It thus lead to the following warning.
[ 47.409729] omap-mcbsp: clks: could not clk_get() prcm_fck
Fix that by changing the opt_clk role to prcm_fck.
Reported-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP4 usb_host_fs (OHCI) and AESS IP blocks require some special
programming for them to enter idle. Without this programming, they
will prevent the rest of the chip from entering full chip idle.
To implement the idle programming cleanly, this will take some
coordination between maintainers. This is likely to take some time,
so it is probably best to leave this for 3.6 or 3.7. So, in the
meantime, prevent these IP blocks from being registered.
Later, once the appropriate support is available, this patch can be
reverted.
This second version comments out the IP block data since Benoît didn't
like removing it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
MULTI_IRQ_HANDLER and SPARSE_IRQ are now required everywhere because
mach/irqs.h and mach/entry-macros.S are gone but the symbols are
only selected for AT91SAM9, not for the NOMMU parts.
A few files now need to include linux/io.h directly, which used to
be included through other headers that have changed.
The new at91_aic_irq_priorities variable is only used with CONFIG_OF
enabled and should not be visible otherwise.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The DMADISABLE bit is a semi-automatic bit present in sysconfig register
of some modules. When the DMA must perform read/write accesses, the
DMADISABLE bit is cleared by the hardware. But when the DMA must stop for power
management, software must set the DMADISABLE bit back to 1.
In cases where the ROMCODE/BOOTLOADER uses dma, the hardware clears the
DMADISABLE bit (but the romcode/bootloader might not set it back to 1).
In order for the kernel to start in a clean state, it is
necessary for the kernel to set DMADISABLE bit back to 1 (irrespective
of whether it's been set to 1 in romcode or bootloader).
During _reset of the (hwmod)device, the DMADISABLE bit is set so that it
does not prevent idling of the system. (NOTE: having DMADISABLE to 0,
prevents the system to idle)
DMADISABLE bit is present in usbotgss module of omap5.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[paul@pwsan.com: updated to apply; fixed checkpatch warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some prm and cm registers read/write and status functions
are built only for some custom OMAP2+ builds and are stubbed
in header files for other builds under ifdef statements.
But this results in adding new CONFIG_ARCH_OMAPXXX
checks when SOCs are added in the future. So move them
to a common place for OMAP2+ and make them 'weak' implementations.
This way no new ifdefs would be required in the future and also
cleans up the existing code.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
[paul@pwsan.com: unsplit quoted strings; moved PRM functions to
mach-omap2/prm_common.c; resolved sparse warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add an API to get main clock name associated with a given @oh.
This will avoid the need to construct fclk names during early
initialization in order to get fclk handle using clk_get().
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
If the dpll is already locked, code can be optimized
to return much earlier than doing redundent set of lock mode
and wait on idlest.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The register is used to configure the behaviour of the CSI-2 and CCP-2
receivers. This register is available only in OMAP3630.
The original patch was submitted by Vimarsh Zutshi.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Vimarsh Zutshi <vimarsh.zutshi@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The wake-up power domain is an alway-on power domain and so this power domain
does not have a power state status (PM_PWSTST_xxx) register that indicates the
current state. However, during the registering of the wake-up power domain the
state of the domain is queried by calling pwrdm_read_pwrst(). This actually
tries to read a register that does not exist and returns a value of 0 that
indicates that the current state is OFF. The OFF state count of the wake-up
power domain is then set to 1 and the current state to OFF. Both of which are
incorrect.
To fix this, if a power domain only supports the ON state, do not attempt to
read the power state status register and simply return ON as the current power
state.
This is based upon Tony's current linux-omap master branch.
Testing:
- Boot tested on OMAP4460 panda.
- Boot tested on OMAP3430 beagle and validated CORE RET still working (using
Paul's 32k timer patch [1]).
[1] http://marc.info/?l=linux-omap&m=134000053229888&w=2
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[paul@pwsan.com: edited commit message slightly]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For OMAP3+ devices, the clock domains (CLKDMs) support one or more of the
following transition modes ...
NO_SLEEP (0x0) - A clock domain sleep transition is never initiated,
irrespective of the hardware conditions.
SW_SLEEP (0x1) - A software-forced sleep transition. The transition is initiated
when the associated hardware conditions are satisfied
SW_WKUP (0x2) - A software-forced clock domain wake-up transition is initiated,
irrespective of the hardware conditions.
HW_AUTO (0x3) - Hardware-controlled automatic sleep and wake-up transition is
initiated by the PRCM module when the associated hardware
conditions are satisfied.
For OMAP4 devices, SW_SLEEP is equivalent to HW_AUTO and NO_SLEEP is equivalent
to SW_WKUP. The only difference between HW_AUTO and SW_SLEEP for OMAP4 devices
is that the PRM_IRQSTATUS_MPU.TRANSITION_ST interrupt status is set in case of
SW_SLEEP transition, and not set in case of HW_AUTO transition.
For OMAP4 devices, all CLKDMs support HW_AUTO and therefore we can place the
CLKDMs in the HW_AUTO state instead of the SW_SLEEP mode. Hence, we do not
need to use the SW_SLEEP mode. With regard to NO_SLEEP and SW_WKUP it is
preferred to use SW_WKUP mode if the CLKDM supports it and so use this mode
instead of NO_SLEEP where possible.
For a software perspective the above 4 modes are represented by the following
flags to indicate what modes are supported by each of the CLKDMs.
CLKDM_CAN_DISABLE_AUTO --> NO_SLEEP
CLKDM_CAN_ENABLE_AUTO --> HW_AUTO
CLKDM_CAN_FORCE_SLEEP --> SW_SLEEP
CLKDM_CAN_FORCE_WAKEUP --> SW_WKUP
By eliminating the SW_SLEEP mode the the mapping of the flags for OMAP4 devices
can becomes ...
CLKDM_CAN_DISABLE_AUTO --> NO_SLEEP
CLKDM_CAN_ENABLE_AUTO --> HW_AUTO
CLKDM_CAN_FORCE_SLEEP --> HW_AUTO
CLKDM_CAN_FORCE_WAKEUP --> SW_WKUP
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In case of AM33XX device, XXX_RSTST register offset is not
consistent across PRM modules/instances,
PRM_XXX RSTST
=========================
PRM_PER_MOD: 0x04
PRM_WKUP_MOD: 0x0C
PRM_MPU_MOD: NA
PRM_DEVICE_MOD: 0x08
This means, we need to pass on XXX_RSTST register offset
information through omap_hwmod data, similar to XXX_RSTCTRL.
Currently, this field is only applicable and used for AM33XX
devices.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In case of AM33xx family of devices (like cpsw) have different sysc
bit field offsets defined,
sysc_type3:
| 3 2 | 1 0 |
| STDBYMODE | IDLEMODE |
So introduce new sysc_type3 in omap_hwmod common data.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 0fa1f0609a (ARM: Orion: Fix
Virtual/Physical mixup with watchdog) broke the Dove & MV78xx0
build. Although these two SoC don't use the watchdog, the shared
platform code still needs to build. Add the necessary defines.
Cc: stable@vger.kernel.org
Reported-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 157d2644cb ("ARM: pxa: change gpio
to platform device") removed all includes of mach/gpio-pxa.h. It kept
this unused header in the tree. Using it can't work, as it itself
includes the non-existent header plat/gpio-pxa.h. This header can safely
be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
The SCC clock is needed in internal boot mode and so must keep enabled.
This same issue was fixed for the pre-common-clk code in commit
3d6e614 (mx35: Fix boot ROM hang in internal boot mode)
Cc: John Ogness <jogness@linutronix.de>
Cc: Hans J. Koch <hjk@hansjkoch.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
hwmod, clock, and System Control Module cleanup, and the removal
of the last instance of omap_read/write usage for omap2+ with
the removal of unused USB OHCI Full Speed driver support. The
removed OHCI is only currently used for omap1 as the actively
used omap2+ boards have either MUSB or another instance of
OHCI+EHCI that's more usable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=A9qD
-----END PGP SIGNATURE-----
mergetag object c59b537d87
type commit
tag omap-devel-dmtimer-for-v3.6
tagger Tony Lindgren <tony@atomide.com> 1341130362 -0700
Here are some omap dmtimer changes to make it easier to add
device tree support for dmtimer by simplifying the platform
data structure used by dmtimr.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=L0+0
-----END PGP SIGNATURE-----
mergetag object 6fd8246b1c
type commit
tag omap-devel-am33xx-for-v3.6
tagger Tony Lindgren <tony@atomide.com> 1341131157 -0700
Here are changes to add support for am33xx processors for the
clock, power, and voltagedomains.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=bc0b
-----END PGP SIGNATURE-----
Merge tags 'omap-cleanup-for-v3.6', 'omap-devel-dmtimer-for-v3.6' and 'omap-devel-am33xx-for-v3.6' into devel-am33xx-part2
commit bc8966 (ARM: fiq: change FIQ_START to a variable) introduced the
following build error for imx_v4_v5_defconfig:
arch/arm/plat-mxc/avic.c:220:11: error: 'FIQ_START' undeclared (first use in this function)
Include the missing header file to fix it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
clock, power, and voltagedomains.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=bc0b
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-am33xx-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren <tony@atomide.com>:
Here are changes to add support for am33xx processors for the
clock, power, and voltagedomains.
* tag 'omap-devel-am33xx-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP AM33xx: clockdomains: Add clockdomain data and respective operations
ARM: OMAP AM33xx: powerdomains: add AM335x support
ARM: OMAP AM33xx: CM: Introduce AM33xx CM APIs and register level details
ARM: OMAP AM33xx: PRM: add PRM support
ARM: OMAP AM33xx: voltagedomain: Add voltage domain data
ARM: OMAP2+: control: Add AM33XX control reg & sec clkctrl offset
ARM: OMAP2+: am33xx: Add AM335XEVM machine support
ARM: OMAP2+: am33xx: Add low level debugging support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
code for wake-ups, and improve idle latencies for cpuidle.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=7qEs
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-pm-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/pm
From: Tony Lindgren <tony@atomide.com>:
Here are some omap PM changes that reimplement omap PRCM I/O chain
code for wake-ups, and improve idle latencies for cpuidle.
* tag 'omap-devel-pm-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: PM: fix IRQ_NOAUTOEN removal by mis-merge
ARM: OMAP3: PM: cpuidle: optimize the clkdm idle latency in C1 state
ARM: OMAP3: PM: cpuidle: optimize the PER latency in C1 state
ARM: OMAP3: PM: cpuidle: default to C1 in next_valid_state
ARM: OMAP3: PM: cleanup cam_pwrdm leftovers
ARM: OMAP3: PM: call pre/post transition per powerdomain
ARM: OMAP2+: powerdomain: allow pre/post transtion to be per pwrdm
ARM: OMAP3: PM: Remove IO Daisychain control from cpuidle
ARM: OMAP3PLUS: hwmod: reconfigure IO Daisychain during hwmod mux
ARM: OMAP3+: PRM: Enable IO wake up
ARM: OMAP4: PRM: Add IO Daisychain support
ARM: OMAP3: PM: Move IO Daisychain function to omap3 prm file
ARM: OMAP3: PM: correct enable/disable of daisy io chain
ARM: OMAP2+: PRM: fix compile for OMAP4-only build
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
via the omap tree. These changes convert omap HDQ1W driver to use
runtime PM, and finally move omap SmartReflex driver from arch/arm
to live under drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xsG/
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-driver-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/pm
From Tony Lindgren <tony@atomide.com>:
Here are omap driver changes for v3.6 that were agreed to be merged
via the omap tree. These changes convert omap HDQ1W driver to use
runtime PM, and finally move omap SmartReflex driver from arch/arm
to live under drivers.
* tag 'omap-devel-driver-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: do not allow SmartReflex to be built as a module
ARM: OMAP2: Use hwmod to initialize mmc for 2420
W1: OMAP HDQ1W: use runtime PM
ARM: OMAP2+: HDQ1W: use omap_device
W1: OMAP HDQ1W: use 32-bit register accesses
W1: OMAP HDQ1W: allow driver to be built on all OMAP2+
ARM: OMAP: SmartReflex: Move smartreflex driver to drivers/
ARM: OMAP2+: SmartReflex: add POWER_AVS Kconfig options
ARM: OMAP2+: SmartReflex: Create per-opp debugfs node for errminlimit
ARM: OMAP2+: SmartReflex: Use per-OPP data structure
ARM: OMAP2+: Voltage: Move the omap_volt_data structure to plat
ARM: OMAP2+: SmartReflex: introduce a busy loop condition test macro
ARM: OMAP3: hwmod: rename the smartreflex entries
ARM: OMAP2+: smartreflex: Use the names from hwmod data instead of voltage domains.
ARM: OMAP3+: SmartReflex: class drivers should use struct omap_sr *
ARM: OMAP2+: SmartReflex: move the smartreflex header to include/linux/power
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
device tree support for dmtimer by simplifying the platform
data structure used by dmtimr.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=L0+0
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-dmtimer-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/timer
From Tony Lindgren <tony@atomide.com>:
Here are some omap dmtimer changes to make it easier to add
device tree support for dmtimer by simplifying the platform
data structure used by dmtimr.
* tag 'omap-devel-dmtimer-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Simplify dmtimer clock aliases
ARM: OMAP2+: Move dmtimer clock set function to dmtimer driver
ARM: OMAP1: Fix dmtimer support
ARM: OMAP: Add flag to indicate if a timer needs a manual reset
ARM: OMAP: Remove timer function pointer for context loss counter
ARM: OMAP: Remove loses_context variable from timer platform data
ARM: OMAP2+: Fix external clock support for dmtimers
ARM: OMAP2+: HWMOD: Correct timer device attributes
ARM: OMAP: Add DMTIMER capability variable to represent timer features
ARM: OMAP2+: Add dmtimer platform function to reserve systimers
ARM: OMAP2+: Remove unused max number of timers definition
ARM: OMAP: Remove unnecessary clk structure
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
hwmod, clock, and System Control Module cleanup, and the removal
of the last instance of omap_read/write usage for omap2+ with
the removal of unused USB OHCI Full Speed driver support. The
removed OHCI is only currently used for omap1 as the actively
used omap2+ boards have either MUSB or another instance of
OHCI+EHCI that's more usable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=A9qD
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren <tony@atomide.com>
Here is some more omap clean-up. The biggest changes are
hwmod, clock, and System Control Module cleanup, and the removal
of the last instance of omap_read/write usage for omap2+ with
the removal of unused USB OHCI Full Speed driver support. The
removed OHCI is only currently used for omap1 as the actively
used omap2+ boards have either MUSB or another instance of
OHCI+EHCI that's more usable.
* tag 'omap-cleanup-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: hwmod: remove prm_clkdm, cm_clkdm; allow hwmods to have no clockdomain
ARM: OMAP3: Move McBSP fck clock alias to hwmod data
ARM: OMAP2: Move McBSP fck clock alias to hwmod data for OMAP2430
ARM: OMAP2: Move McBSP fck clock alias to hwmod data for OMAP2420
ARM: OMAP: dsp: interface to control module functions
ARM: OMAP2+: control: new APIs to configure boot address and mode
ARM: OMAP2+: CLEANUP: Remove ARCH_OMAPx ifdef from struct dpll_data
ARM: OMAP2+: hwmod: use init-time function pointer for _init_clkdm
ARM: OMAP2+: hwmod: use init-time function pointer for hardreset
ARM: OMAP2+: hwmod: use init-time function pointer for wait_target_ready
ARM: OMAP4: hwmod: drop extra cpu_is check from _wait_target_disable()
ARM: OMAP2+: hwmod: use init-time function ptrs for enable/disable module
ARM: OMAP4: hwmod: rename _enable_module to _omap4_enable_module()
ARM: OMAP: Make FS USB omap1 only
ARM: OMAP2: Remove legacy USB FS support
ARM: OMAP3: There is no FS USB controller on omap3
ARM: OMAP: dma: Clear status registers on enable/disable irq
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
critical enough for the 3.5 -rc cycle. The biggest changes are
fixes for the am35xx clock and hwmod data, and the removal of dead
code for the 730 and 850 headers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJP8AHPAAoJEBvUPslcq6VzXbcP/0EIL3u8e8eAjXJok1F5NT8u
U8ESDp29dR+5WrfuXpL+EnDxMuQxn0eITpeCm0rzREMm3cg+b7prqArWmcusaj3Y
lt3Th6t+1X/kJYc5RSsnTpWFTpN+2Ycten8cRDCGT2k/3kM8ZmFHfK7mMUMgaCEZ
yNMl75Db45RMMAM7ZFjwSbiLSyFdNYb7fgDyJPJpl8DiMQDLSyUshKpFjECFFv8L
zxALEpvqvb4nPHiynAju6mSDY8zCRLyl0ogRcp+Gqxv1GdZpxM5nR2g9ObnBeflo
sTyC5D/johsOMkv4+npUzodEdqBcaBZS9YZ5CRiFRdN6c+Cxan2tprJZfvJpgHsZ
TMT1aVH2xuu55FWbC7ne/1LDrmMzwbxAHclPYy+toy0Aks5cMy2QMz6lmHDZUfMv
bvoF/UwZ1g3cpO6LERmRjyrTVbPwNAeR+omKKkjcilvT0bVvDTORgRTZjvAOKW4J
lVGBOEijcU1MUAOoYafKssvgl4rouXiZR2pOyoC6+LUqj7aEPjK4+YftPgyhGMz+
M5kR92DBYIsJP42xV84BBubpVIgr6zz1jwT3ttMv5XZF/Ua9cM3WprLnbgLXAjiz
lZfLGgCL85XU0ArtjJSDi6xyffzWEQrh/RgHs/pN4LBWcQfTnlbL2KfuthXv2IYZ
WCtK57YjjjAG58xhjJV0
=UD1/
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-non-critical-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
From Tony Lindgren <tony@atomide.com>:
This branch contains fixes that were too intrusive or not
critical enough for the 3.5 -rc cycle. The biggest changes are
fixes for the am35xx clock and hwmod data, and the removal of dead
code for the 730 and 850 headers.
* tag 'omap-fixes-non-critical-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (25 commits)
ARM: OMAP2+: fix CONFIG_CPU_IDLE dependency on CONFIG_PM
ARM: OMAP: remove unused cpu detection macros
ARM: OMAP: fix typos related to OMAP330
ARM: OMAP7XX: Remove omap730.h and omap850.h
ARM: OMAP2+: fix naming collision of variable nr_irqs
ARM: OMAP: omap2plus_defconfig: Enable EXT4 support
ARM: OMAP depends on MMU
arm: omap3: am35x: Set proper powerdomain states
ARM: OMAP AM35x: clockdomain data: Fix clockdomain dependencies
ARM: OMAP AM35x: EMAC/MDIO integration: Add Davinci EMAC/MDIO hwmod support
ARM: OMAP: AM35xx: fix UART4 softreset
ARM: OMAP AM35xx: clock and hwmod data: fix UART4 data
ARM: OMAP AM35xx: clock and hwmod data: fix AM35xx HSOTGUSB hwmod
ARM: OMAP: Fix dts files w/ status property: "disable" -> "disabled"
ARM: OMAP: beagle: Set USB Host Port 1 to OMAP_USBHS_PORT_MODE_UNUSED
ARM: OMAP2: twl-common: Fix compiler warning
ARM: OMAP: fix the ads7846 init code
mfd: twl: remove pdata->irq_base/_end, no more users
ARM: OMAP2+: TWL: remove usage of pdata->irq_base/_end
ARM: OMAP2+: OPP: Fix to ensure check of right oppdef after bad one
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A second batch of core patches for lpc32xx, based on top of the first
one in the lpc32xx-next branch.
* 'lpc32xx/core' of git://git.antcom.de/linux-2.6:
ARM: LPC32xx: Remove unused gpios
ARM: LPC32xx: Remove USB and I2C init from phy3250.c
ARM: LPC32xx: Cleanup USB clock init
ARM: LPC32xx: Remove wrong re-initialization of MMC clock register
ARM: LPC32xx: Add further bits to MMC init
ARM: LPC32xx: Init MMC via clock
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This branch contains device tree changes for lpc32xx that are
based on top of the earlier lpc32xx-next branch.
* 'lpc32xx/dts' of git://git.antcom.de/linux-2.6:
ARM: LPC32xx: Update DTS file for EA3250 board
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Device's regulator matches their hardware counterparts with the
property "regulator-compatible" of each child regulator node in
place of the child node name.
Add the property "regulator-compatible" for each regulator with
their hardware counterpart's name.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If sigp sense doesn't have any status bits to report, it should set
cc 0 and leave the register as-is.
Since we know about the external call pending bit, we should report
it if it is set as well.
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Just use the defines instead of using plain numbers and adding
a comment behind each line.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If an invalid parameter is passed or the addressed cpu is in an
incorrect state sigp set prefix will store a status.
This status must only have bits set as defined by the architecture.
The current kvm implementation missed to clear bits and also did
not set the intended status bit ("and" instead of "or" operation).
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Only if the sensed cpu is not running a status is stored, which
is reflected by condition code 1. If the cpu is running, condition
code 0 should be returned.
Just the opposite of what the code is doing.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The smp and the kvm code have different defines for the sigp order codes.
Let's just have a single place where these are defined.
Also move the sigp condition code and sigp cpu status bits to the new
sigp.h header file.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
condition code "status stored" for sigp sense running always implies
that only the "not running" status bit is set. Therefore no need to
check if it is set.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Pawel Moll