The device tree binding documentation for dsa explicitely states that a
DSA node should have its #address-cells property set to 2, yet the
example still used 1, fix that typo.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for registering DSA switches using Device Tree
bindings. Note that we support programming the switch routing table even
though no in-tree user seems to require it. I tested this on Armada 370
with a Marvell 88E6172 (not supported by mainline yet).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enhances the "mvmdio" to support a SMI error/done interrupt
line which can be used along with a wait queue instead of doing
busy-waiting on the registers. This is a feature which is available in
the mv643xx_eth SMI code and thus reduces again the gap between the two.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements F-RTO (foward RTO recovery):
When the first retransmission after timeout is acknowledged, F-RTO
sends new data instead of old data. If the next ACK acknowledges
some never-retransmitted data, then the timeout was spurious and the
congestion state is reverted. Otherwise if the next ACK selectively
acknowledges the new data, then the timeout was genuine and the
loss recovery continues. This idea applies to recurring timeouts
as well. While F-RTO sends different data during timeout recovery,
it does not (and should not) change the congestion control.
The implementaion follows the three steps of SACK enhanced algorithm
(section 3) in RFC5682. Step 1 is in tcp_enter_loss(). Step 2 and
3 are in tcp_process_loss(). The basic version is not supported
because SACK enhanced version also works for non-SACK connections.
The new implementation is functionally in parity with the old F-RTO
implementation except the one case where it increases undo events:
In addition to the RFC algorithm, a spurious timeout may be detected
without sending data in step 2, as long as the SACK confirms not
all the original data are dropped. When this happens, the sender
will undo the cwnd and perhaps enter fast recovery instead. This
additional check increases the F-RTO undo events by 5x compared
to the prior implementation on Google Web servers, since the sender
often does not have new data to send for HTTP.
Note F-RTO may detect spurious timeout before Eifel with timestamps
does so.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch series refactor the F-RTO feature (RFC4138/5682).
This is to simplify the loss recovery processing. Existing F-RTO
was developed during the experimental stage (RFC4138) and has
many experimental features. It takes a separate code path from
the traditional timeout processing by overloading CA_Disorder
instead of using CA_Loss state. This complicates CA_Disorder state
handling because it's also used for handling dubious ACKs and undos.
While the algorithm in the RFC does not change the congestion control,
the implementation intercepts congestion control in various places
(e.g., frto_cwnd in tcp_ack()).
The new code implements newer F-RTO RFC5682 using CA_Loss processing
path. F-RTO becomes a small extension in the timeout processing
and interfaces with congestion control and Eifel undo modules.
It lets congestion control (module) determines how many to send
independently. F-RTO only chooses what to send in order to detect
spurious retranmission. If timeout is found spurious it invokes
existing Eifel undo algorithms like DSACK or TCP timestamp based
detection.
The first patch removes all F-RTO code except the sysctl_tcp_frto is
left for the new implementation. Since CA_EVENT_FRTO is removed, TCP
westwood now computes ssthresh on regular timeout CA_EVENT_LOSS event.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
The following patchset contains 7 Netfilter/IPVS fixes for 3.9-rc, they are:
* Restrict IPv6 stateless NPT targets to the mangle table. Many users are
complaining that this target does not work in the nat table, which is the
wrong table for it, from Florian Westphal.
* Fix possible use before initialization in the netns init path of several
conntrack protocol trackers (introduced recently while improving conntrack
netns support), from Gao Feng.
* Fix incorrect initialization of copy_range in nfnetlink_queue, spotted
by Eric Dumazet during the NFWS2013, patch from myself.
* Fix wrong calculation of next SCTP chunk in IPVS, from Julian Anastasov.
* Remove rcu_read_lock section in IPVS while calling ipv4_update_pmtu
not required anymore after change introduced in 3.7, again from Julian.
* Fix SYN looping in IPVS state sync if the backup is used a real server
in DR/TUN modes, this required a new /proc entry to disable the director
function when acting as backup, also from Julian.
* Remove leftover IP_NF_QUEUE Kconfig after ip_queue removal, noted by
Paul Bolle.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Akindinov is reporting for a problem where SYNs are looping
between the master and backup server when the backup server is used as
real server in DR mode and has IPVS rules to function as director.
Even when the backup function is enabled we continue to forward
traffic and schedule new connections when the current master is using
the backup server as real server. While this is not a problem for NAT,
for DR and TUN method the backup server can not determine if a request
comes from client or from director.
To avoid such loops add new sysctl flag backup_only. It can be needed
for DR/TUN setups that do not need backup and director function at the
same time. When the backup function is enabled we stop any forwarding
and pass the traffic to the local stack (real server mode). The flag
disables the director function when the backup function is enabled.
For setups that enable backup function for some virtual services and
director function for other virtual services there should be another
more complex solution to support DR/TUN mode, may be to assign
per-virtual service syncid value, so that we can differentiate the
requests.
Reported-by: Dmitry Akindinov <dimak@stalker.com>
Tested-by: German Myzovsky <lawyer@sipnet.ru>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
TCPCT uses option-number 253, reserved for experimental use and should
not be used in production environments.
Further, TCPCT does not fully implement RFC 6013.
As a nice side-effect, removing TCPCT increases TCP's performance for
very short flows:
Doing an apache-benchmark with -c 100 -n 100000, sending HTTP-requests
for files of 1KB size.
before this patch:
average (among 7 runs) of 20845.5 Requests/Second
after:
average (among 7 runs) of 21403.6 Requests/Second
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this one we have:
- An ab8500 build failure fix.
- An ab8500 device tree parsing fix.
- A fix for twl4030_madc remove routine to work properly (when built-in).
- A fix for properly registering palmas interrupt handler.
- A fix for omap-usb init routine to actually write into the hostconfig
register.
- A couple of warning fixes for ab8500-gpadc and tps65912.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=XFgy
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-fixes
Pull MFD fixes from Samuel Ortiz:
"This is the first batch of MFD fixes for 3.9.
With this one we have:
- An ab8500 build failure fix.
- An ab8500 device tree parsing fix.
- A fix for twl4030_madc remove routine to work properly (when
built-in).
- A fix for properly registering palmas interrupt handler.
- A fix for omap-usb init routine to actually write into the
hostconfig register.
- A couple of warning fixes for ab8500-gpadc and tps65912"
* tag 'mfd-fixes-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-fixes:
mfd: twl4030-madc: Remove __exit_p annotation
mfd: ab8500: Kill "reg" property from binding
mfd: ab8500-gpadc: Complain if we fail to enable vtvout LDO
mfd: wm831x: Don't forward declare enum wm831x_auxadc
mfd: twl4030-audio: Fix argument type for twl4030_audio_disable_resource()
mfd: tps65912: Declare and use tps65912_irq_exit()
mfd: palmas: Provide irq flags through DT/platform data
mfd: Make AB8500_CORE select POWER_SUPPLY to fix build error
mfd: omap-usb-host: Actually update hostconfig
The default value is 128, not 256
#grep gc_thresh1 net/ -rI
net/decnet/dn_neigh.c: .gc_thresh1 = 128,
net/ipv6/ndisc.c: .gc_thresh1 = 128,
net/ipv4/arp.c: .gc_thresh1 = 128,
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some tty/serial driver fixes for 3.9
We finally mute the annoying WARN_ON that lots of people are hitting and
it turns out isn't needed anymore. Also add a few new device ids and a
some other minor fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlFA30EACgkQMUfUDdst+ylTwACfTdhZhFWStj/3jlIDzdxz6Bjv
cwkAn2c4TomoV5wTu9pvRBkEF4WsDJTS
=98sU
-----END PGP SIGNATURE-----
Merge tag 'tty-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg Kroah-Hartman:
"Here are some tty/serial driver fixes for 3.9
We finally mute the annoying WARN_ON that lots of people are hitting
and it turns out isn't needed anymore. Also add a few new device ids
and a some other minor fixes."
* tag 'tty-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: fix typo "SERIAL_S3C2412"
serial: 8250: Keep 8250.<xxxx> module options functional after driver rename
tty: serial: fix typo "ARCH_S5P6450"
tty/8250_pnp: serial port detection regression since v3.7
serial: bcm63xx_uart: fix compilation after "TTY: switch tty_insert_flip_char"
serial: 8250_pci: add support for another kind of NetMos Technology PCI 9835 Multi-I/O Controller
Fix 4 port and add support for 8 port 'Unknown' PCI serial port cards
tty/serial: Add support for Altera serial port
tty: serial: vt8500: Unneccessary duplicated clock code removed
tty: serial: mpc5xxx: fix PSC clock name bug
TTY: disable debugging warning
Network coding exploits the 802.11 shared medium to allow multiple
packets to be sent in a single transmission. In brief, a relay can XOR
two packets, and send the coded packet to two destinations. The
receivers can decode one of the original packets by XOR'ing the coded
packet with the other original packet. This will lead to increased
throughput in topologies where two packets cross one relay.
In a simple topology with three nodes, it takes four transmissions
without network coding to get one packet from Node A to Node B and one
from Node B to Node A:
1. Node A ---- p1 ---> Node R Node B
2. Node A Node R <--- p2 ---- Node B
3. Node A <--- p2 ---- Node R Node B
4. Node A Node R ---- p1 ---> Node B
With network coding, the relay only needs one transmission, which saves
us one slot of valuable airtime:
1. Node A ---- p1 ---> Node R Node B
2. Node A Node R <--- p2 ---- Node B
3. Node A <- p1 x p2 - Node R - p1 x p2 -> Node B
The same principle holds for a topology including five nodes. Here the
packets from Node A and Node B are overheard by Node C and Node D,
respectively. This allows Node R to send a network coded packet to save
one transmission:
Node A Node B
| \ / |
| p1 p2 |
| \ / |
p1 > Node R < p2
| |
| / \ |
| p1 x p2 p1 x p2 |
v / \ v
/ \
Node C < > Node D
More information is available on the open-mesh.org wiki[1].
This patch adds the initial code to support network coding in
batman-adv. It sets up a worker thread to do house keeping and adds a
sysfs file to enable/disable network coding. The feature is disabled by
default, as it requires a wifi-driver with working promiscuous mode, and
also because it adds a small delay at each hop.
[1] http://www.open-mesh.org/projects/batman-adv/wiki/Catwoman
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Change cpts_active_slave to active_slave so that the same DT property
can be used to ethtool and SIOCGMIIPHY.
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all the slave note properties to separate section to reduce the
confusion between slave note properties and cpsw node properties
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Altera 8250/16550 compatible serial port.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch series implement the Tail loss probe (TLP) algorithm described
in http://tools.ietf.org/html/draft-dukkipati-tcpm-tcp-loss-probe-01. The
first patch implements the basic algorithm.
TLP's goal is to reduce tail latency of short transactions. It achieves
this by converting retransmission timeouts (RTOs) occuring due
to tail losses (losses at end of transactions) into fast recovery.
TLP transmits one packet in two round-trips when a connection is in
Open state and isn't receiving any ACKs. The transmitted packet, aka
loss probe, can be either new or a retransmission. When there is tail
loss, the ACK from a loss probe triggers FACK/early-retransmit based
fast recovery, thus avoiding a costly RTO. In the absence of loss,
there is no change in the connection state.
PTO stands for probe timeout. It is a timer event indicating
that an ACK is overdue and triggers a loss probe packet. The PTO value
is set to max(2*SRTT, 10ms) and is adjusted to account for delayed
ACK timer when there is only one oustanding packet.
TLP Algorithm
On transmission of new data in Open state:
-> packets_out > 1: schedule PTO in max(2*SRTT, 10ms).
-> packets_out == 1: schedule PTO in max(2*RTT, 1.5*RTT + 200ms)
-> PTO = min(PTO, RTO)
Conditions for scheduling PTO:
-> Connection is in Open state.
-> Connection is either cwnd limited or no new data to send.
-> Number of probes per tail loss episode is limited to one.
-> Connection is SACK enabled.
When PTO fires:
new_segment_exists:
-> transmit new segment.
-> packets_out++. cwnd remains same.
no_new_packet:
-> retransmit the last segment.
Its ACK triggers FACK or early retransmit based recovery.
ACK path:
-> rearm RTO at start of ACK processing.
-> reschedule PTO if need be.
In addition, the patch includes a small variation to the Early Retransmit
(ER) algorithm, such that ER and TLP together can in principle recover any
N-degree of tail loss through fast recovery. TLP is controlled by the same
sysctl as ER, tcp_early_retrans sysctl.
tcp_early_retrans==0; disables TLP and ER.
==1; enables RFC5827 ER.
==2; delayed ER.
==3; TLP and delayed ER. [DEFAULT]
==4; TLP only.
The TLP patch series have been extensively tested on Google Web servers.
It is most effective for short Web trasactions, where it reduced RTOs by 15%
and improved HTTP response time (average by 6%, 99th percentile by 10%).
The transmitted probes account for <0.5% of the overall transmissions.
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ab8500 device is a child of the prcmu device, which is a memory mapped
bus device, whose children are addressable using physical memory addresses,
not using mailboxes, so a mailbox number in the ab8500 node cannot be
parsed by DT. Nothing uses this number, since it was only introduced
as part of the failed attempt to clean up prcmu mailbox handling, and
we can simply remove it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pull perf fixes from Ingo Molnar:
"Misc minor fixes mostly related to tracing"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
s390: Fix a header dependencies related build error
tracing: update documentation of snapshot utility
tracing: Do not return EINVAL in snapshot when not allocated
tracing: Add help of snapshot feature when snapshot is empty
ftrace: Update the kconfig for DYNAMIC_FTRACE
Pull networking fixes from David Miller:
1) Missing cancel of work items in mac80211 MLME, from Ben Greear.
2) Fix DMA mapping handling in iwlwifi by using coherent DMA for
command headers, from Johannes Berg.
3) Decrease the amount of pressure on the page allocator by using order
1 pages less in iwlwifi, from Emmanuel Grumbach.
4) Fix mesh PS broadcast OOPS in mac80211, from Marco Porsch.
5) Don't forget to recalculate idle state in mac80211 monitor
interface, from Felix Fietkau.
6) Fix varargs in netfilter conntrack handler, from Joe Perches.
7) Need to reset entire chip when command queue fills up in iwlwifi,
from Emmanuel Grumbach.
8) The TX antenna value must be valid when calibrations are performed
in iwlwifi, fix from Dor Shaish.
9) Don't generate netfilter audit log entries when audit is disabled,
from Gao Feng.
10) Deal with DMA unit hang on e1000e during power state transitions,
from Bruce Allan.
11) Remove BUILD_BUG_ON check from igb driver, from Alexander Duyck.
12) Fix lockdep warning on i2c handling of igb driver, from Carolyn
Wyborny.
13) Fix several TTY handling issues in IRDA ircomm tty driver, from
Peter Hurley.
14) Several QFQ packet scheduler fixes from Paolo Valente.
15) When VXLAN encapsulates on transmit, we have to reset the netfilter
state. From Zang MingJie.
16) Fix jiffie check in net_rx_action() so that we really cap the
processing at 2HZ. From Eric Dumazet.
17) Fix erroneous trigger of IP option space exhaustion, when routers
are pre-specified and we are looking to see if we can insert a
timestamp, we will have the space. From David Ward.
18) Fix various issues in benet driver wrt waiting for firmware to
finish POST after resets or errors. From Gavin Shan and Sathya
Perla.
19) Fix TX locking in SFC driver, from Ben Hutchings.
20) Like the VXLAN fix above, when we encap in a TUN device we have to
reset the netfilter state. This should fix several strange crashes
reported by Dave Jones and others. From Eric Dumazet.
21) Don't forget to clean up MAC address resources when shutting down a
port in mlx4 driver, from Yan Burman.
22) Fix divide by zero in vmxnet3 driver, from Bhavesh Davda.
23) Fix device statistic regression in tg3 when the driver is using
phylib, from Nithin Sujir.
24) Fix info leak in several netlink handlers, from Mathias Krause.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (79 commits)
6lowpan: Fix endianness issue in is_addr_link_local().
rrunner.c: fix possible memory leak in rr_init_one()
dcbnl: fix various netlink info leaks
rtnl: fix info leak on RTM_GETLINK request for VF devices
bridge: fix mdb info leaks
tg3: Update link_up flag for phylib devices
ipv6: stop multicast forwarding to process interface scoped addresses
bridging: fix rx_handlers return code
netlabel: fix build problems when CONFIG_IPV6=n
drivers/isdn: checkng length to be sure not memory overflow
net/rds: zero last byte for strncpy
bnx2x: Fix SFP+ misconfiguration in iSCSI boot scenario
bnx2x: Fix intermittent long KR2 link up time
macvlan: Set IFF_UNICAST_FLT flag to prevent unnecessary promisc mode.
team: unsyc the devices addresses when port is removed
bridge: add missing vid to br_mdb_get()
Fix: sparse warning in inet_csk_prepare_forced_close
afkey: fix a typo
MAINTAINERS: Update qlcnic maintainers list
netlabel: correctly list all the static label mappings
...
Pull input updates from Dmitry Torokhov:
"Except for the largish change to the ALPS driver adding "Dolphin V1"
support and Wacom getting a new signature of yet another device, the
rest are straightforward driver fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: mms114 - Fix regulator enable and disable paths
Input: ads7864 - check return value of regulator enable
Input: tc3589x-keypad - fix keymap size
Input: wacom - add support for 0x10d
Input: ALPS - update documentation for recent touchpad driver mods
Input: ALPS - add "Dolphin V1" touchpad support
Input: ALPS - remove unused argument to alps_enter_command_mode()
Input: cypress_ps2 - fix trackpadi found in Dell XPS12
Now, "snapshot" file returns success on a reset of snapshot buffer
even if the buffer wasn't allocated, instead of returning EINVAL.
This patch updates snapshot desctiption according to the change.
Link: http://lkml.kernel.org/r/51399409.4090207@hitachi.com
Signed-off-by: Hiraku Toyooka <hiraku.toyooka.gu@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
- Two fixes for the new intel_pstate driver from Dirk Brandewie.
- Fix for incorrect usage of the .find_bridge() callback from struct
acpi_bus_type in the USB core and subsequent removal of that
callback from Rafael J. Wysocki.
- ACPI processor driver cleanups from Chen Gang and Syam Sidhardhan.
- ACPI initialization and error messages fix from Joe Perches.
- Operating Performance Points documentation improvement from
Nishanth Menon.
- Fixes for memory leaks and potential concurrency issues and sysfs
attributes leaks during device removal in the core device PM QoS
code from Rafael J. Wysocki.
- Calxeda Highbank cpufreq driver simplification from Emilio López.
- cpufreq comment cleanup from Namhyung Kim.
- Fix for a section mismatch in Calxeda Highbank interprocessor
communication code from Mark Langsdorf (this is not a PM fix
strictly speaking, but the code in question went in through the
PM tree).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=9vaj
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael J Wysocki:
- Two fixes for the new intel_pstate driver from Dirk Brandewie.
- Fix for incorrect usage of the .find_bridge() callback from struct
acpi_bus_type in the USB core and subsequent removal of that callback
from Rafael J Wysocki.
- ACPI processor driver cleanups from Chen Gang and Syam Sidhardhan.
- ACPI initialization and error messages fix from Joe Perches.
- Operating Performance Points documentation improvement from Nishanth
Menon.
- Fixes for memory leaks and potential concurrency issues and sysfs
attributes leaks during device removal in the core device PM QoS code
from Rafael J Wysocki.
- Calxeda Highbank cpufreq driver simplification from Emilio López.
- cpufreq comment cleanup from Namhyung Kim.
- Fix for a section mismatch in Calxeda Highbank interprocessor
communication code from Mark Langsdorf (this is not a PM fix strictly
speaking, but the code in question went in through the PM tree).
* tag 'pm+acpi-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq / intel_pstate: Do not load on VM that does not report max P state.
cpufreq / intel_pstate: Fix intel_pstate_init() error path
ACPI / glue: Drop .find_bridge() callback from struct acpi_bus_type
ACPI / glue: Add .match() callback to struct acpi_bus_type
ACPI / porocessor: Beautify code, pr->id is u32 which is never < 0
ACPI / processor: Remove redundant NULL check before kfree
ACPI / Sleep: Avoid interleaved message on errors
PM / QoS: Remove device PM QoS sysfs attributes at the right place
PM / QoS: Fix concurrency issues and memory leaks in device PM QoS
cpufreq: highbank: do not initialize array with a loop
PM / OPP: improve introductory documentation
cpufreq: Fix a typo in comment
mailbox, pl320-ipc: remove __init from probe function
mostly little bugfixes.
Only "feature" is a new RAID10 layout which slightly
improves the number of sets of devices that can concurrently
fail, without data loss.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=YdVD
-----END PGP SIGNATURE-----
Merge tag 'md-3.9' of git://neil.brown.name/md
Pull md updates from NeilBrown:
"Mostly little bugfixes.
Only "feature" is a new RAID10 layout which slightly improves the
number of sets of devices that can concurrently fail, without data
loss."
* tag 'md-3.9' of git://neil.brown.name/md:
md: expedite metadata update when switching read-auto -> active
md: remove CONFIG_MULTICORE_RAID456
md/raid1,raid10: fix deadlock with freeze_array()
md/raid0: improve error message when converting RAID4-with-spares to RAID0
md: raid0: fix error return from create_stripe_zones.
md: fix two bugs when attempting to resize RAID0 array.
DM RAID: Add support for MD's RAID10 "far" and "offset" algorithms
MD RAID10: Improve redundancy for 'far' and 'offset' algorithms (part 2)
MD RAID10: Improve redundancy for 'far' and 'offset' algorithms (part 1)
MD RAID10: Minor non-functional code changes
md: raid1,10: Handle REQ_WRITE_SAME flag in write bios
md: protect against crash upon fsync on ro array
Make Operating Performance Points (OPP) library introductory chapter
a little more reader-friendly. Split the chapter into two sections,
highlight the definition with an example and minor rewording to be
verbose.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The adt7410 driver supports the ADT7420, but its documentation file
makes no mention of that. Add this refrence, and a brief a description
of the differences between the ADT7410 and the ADT7420.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Links to datasheets are no longer valid. Provide links to product information
instead (which provides links to the datasheets and is hopefully more
persistent).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Most of the hwmon driver documentation still listed my old invalid e-mail
address. Fix it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
This adds core architecture support for Imagination's Meta processor
cores, followed by some later miscellaneous arch/metag cleanups and
fixes which I kept separate to ease review:
- Support for basic Meta 1 (ATP) and Meta 2 (HTP) core architecture
- A few fixes all over, particularly for symbol prefixes
- A few privilege protection fixes
- Several cleanups (setup.c includes, split out a lot of metag_ksyms.c)
- Fix some missing exports
- Convert hugetlb to use vm_unmapped_area()
- Copy device tree to non-init memory
- Provide dma_get_sgtable()
Signed-off-by: James Hogan <james.hogan@imgtec.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=65cR
-----END PGP SIGNATURE-----
Merge tag 'metag-v3.9-rc1-v4' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull new ImgTec Meta architecture from James Hogan:
"This adds core architecture support for Imagination's Meta processor
cores, followed by some later miscellaneous arch/metag cleanups and
fixes which I kept separate to ease review:
- Support for basic Meta 1 (ATP) and Meta 2 (HTP) core architecture
- A few fixes all over, particularly for symbol prefixes
- A few privilege protection fixes
- Several cleanups (setup.c includes, split out a lot of
metag_ksyms.c)
- Fix some missing exports
- Convert hugetlb to use vm_unmapped_area()
- Copy device tree to non-init memory
- Provide dma_get_sgtable()"
* tag 'metag-v3.9-rc1-v4' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag: (61 commits)
metag: Provide dma_get_sgtable()
metag: prom.h: remove declaration of metag_dt_memblock_reserve()
metag: copy devicetree to non-init memory
metag: cleanup metag_ksyms.c includes
metag: move mm/init.c exports out of metag_ksyms.c
metag: move usercopy.c exports out of metag_ksyms.c
metag: move setup.c exports out of metag_ksyms.c
metag: move kick.c exports out of metag_ksyms.c
metag: move traps.c exports out of metag_ksyms.c
metag: move irq enable out of irqflags.h on SMP
genksyms: fix metag symbol prefix on crc symbols
metag: hugetlb: convert to vm_unmapped_area()
metag: export clear_page and copy_page
metag: export metag_code_cache_flush_all
metag: protect more non-MMU memory regions
metag: make TXPRIVEXT bits explicit
metag: kernel/setup.c: sort includes
perf: Enable building perf tools for Meta
metag: add boot time LNKGET/LNKSET check
metag: add __init to metag_cache_probe()
...
Pull watchdog updates from Wim Van Sebroeck:
"This contains:
- fixes and improvements
- devicetree bindings
- conversion to watchdog generic framework of the following drivers:
- booke_wdt
- bcm47xx_wdt.c
- at91sam9_wdt
- Removal of old STMP3xxx driver
- Addition of following new drivers:
- new driver for STMP3xxx and i.MX23/28
- Retu watchdog driver"
* git://www.linux-watchdog.org/linux-watchdog: (30 commits)
watchdog: sp805_wdt depends on ARM
watchdog: davinci_wdt: update to devm_* API
watchdog: davinci_wdt: use devm managed clk get
watchdog: at91rm9200: add DT support
watchdog: add timeout-sec property binding
watchdog: at91sam9_wdt: Convert to use the watchdog framework
watchdog: omap_wdt: Add option nowayout
watchdog: core: dt: add support for the timeout-sec dt property
watchdog: bcm47xx_wdt.c: add hard timer
watchdog: bcm47xx_wdt.c: rename wdt_time to timeout
watchdog: bcm47xx_wdt.c: rename ops methods
watchdog: bcm47xx_wdt.c: use platform device
watchdog: bcm47xx_wdt.c: convert to watchdog core api
watchdog: Convert BookE watchdog driver to watchdog infrastructure
watchdog: s3c2410_wdt: Use devm_* functions
watchdog: remove old STMP3xxx driver
watchdog: add new driver for STMP3xxx and i.MX23/28
rtc: stmp3xxx: add wdt-accessor function
watchdog: introduce retu_wdt driver
watchdog: intel_scu_watchdog: fix Kconfig dependency
...
Pull second set of slave-dmaengine updates from Vinod Koul:
"Arnd's patch moves the dw_dmac to use generic DMA binding. I agreed
to merge this late as it will avoid the conflicts between trees.
The second patch from Matt adding a dma_request_slave_channel_compat
API was supposed to be picked up, but somehow never got picked up.
Some patches dependent on this are already in -next :("
* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: dw_dmac: move to generic DMA binding
dmaengine: add dma_request_slave_channel_compat()
Pull x86 platform driver updates from Matthew Garrett:
"Mostly relatively small updates, along with some hardware enablement
for Sony hardware and a pile of updates to Google's Chromebook driver"
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (49 commits)
ideapad-laptop: Depend on BACKLIGHT_CLASS_DEVICE instead of selecting it
ideapad: depends on backlight subsystem and update comment
Platform: x86: chromeos_laptop - add i915 gmbuses to adapter names
Platform: x86: chromeos_laptop - Add isl light sensor for Pixel
Platform: x86: chromeos_laptop - Add a more general add_i2c_device
Platform: x86: chromeos_laptop - Add Pixel Touchscreen
Platform: x86: chromeos_laptop - Add support for probing devices
Platform: x86: chromeos_laptop - Add Pixel Trackpad
hp-wmi: fix handling of platform device
sony-laptop: leak in error handling sony_nc_lid_resume_setup()
hp-wmi: Add support for SMBus hotkeys
asus-wmi: Fix unused function build warning
acer-wmi: avoid the warning of 'devices' may be used uninitialized
drivers/platform/x86/thinkpad_acpi.c: Handle HKEY event 0x6040
Platform: x86: chromeos_laptop - Add HP Pavilion 14
Platform: x86: chromeos_laptop - Add Taos tsl2583 device
Platform: x86: chromeos_laptop - Add Taos tsl2563 device
Platform: x86: chromeos_laptop - Add Acer C7 trackpad
Platform: x86: chromeos_laptop - Rename setup_lumpy_tp to setup_cyapa_smbus_tp
asus-laptop: always report brightness key events
...
* misc clean-ups in the MTD command-line partitioning parser (cmdlinepart)
* add flash locking support for STmicro chips serial flash chips, as well as
for CFI command set 2 chips.
* new driver for the ELM error correction HW module found in various TI chips,
enable the OMAP NAND driver to use the ELM HW error correction
* added number of new serial flash IDs
* various fixes and improvements in the gpmi NAND driver
* bcm47xx NAND driver improvements
* make the mtdpart module actually removable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iEYEABECAAYFAlExEs8ACgkQdwG7hYl686Oa+gCgiBNt+I0MiixDeN+MGuE1uw9s
i2wAniD9sR2HDy6y5SkbdXK/aPr8ez/p
=xV1l
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20130301' of git://git.infradead.org/linux-mtd
Pull MTD update from David Woodhouse:
"Fairly unexciting MTD merge for 3.9:
- misc clean-ups in the MTD command-line partitioning parser
(cmdlinepart)
- add flash locking support for STmicro chips serial flash chips, as
well as for CFI command set 2 chips.
- new driver for the ELM error correction HW module found in various
TI chips, enable the OMAP NAND driver to use the ELM HW error
correction
- added number of new serial flash IDs
- various fixes and improvements in the gpmi NAND driver
- bcm47xx NAND driver improvements
- make the mtdpart module actually removable"
* tag 'for-linus-20130301' of git://git.infradead.org/linux-mtd: (45 commits)
mtd: map: BUG() in non handled cases
mtd: bcm47xxnflash: use pr_fmt for module prefix in messages
mtd: davinci_nand: Use managed resources
mtd: mtd_torturetest can cause stack overflows
mtd: physmap_of: Convert device allocation to managed devm_kzalloc()
mtd: at91: atmel_nand: for PMECC, add code to check the ONFI parameter ECC requirement.
mtd: atmel_nand: make pmecc-cap, pmecc-sector-size in dts is optional.
mtd: atmel_nand: avoid to report an error when lookup table offset is 0.
mtd: bcm47xxsflash: adjust names of bus-specific functions
mtd: bcm47xxpart: improve probing of nvram partition
mtd: bcm47xxpart: add support for other erase sizes
mtd: bcm47xxnflash: register this as normal driver
mtd: bcm47xxnflash: fix message
mtd: bcm47xxsflash: register this as normal driver
mtd: bcm47xxsflash: write number of written bytes
mtd: gpmi: add sanity check for the ECC
mtd: gpmi: set the Golois Field bit for mx6q's BCH
mtd: devices: elm: Removes <xx> literals in elm DT node
mtd: gpmi: fix a dereferencing freed memory error
mtd: fix the wrong timeo for panic_nand_wait()
...
Add basic metag documentation. This includes an outline description of
the ABIs (including syscall ABI) and calling conventions, similar to the
one in Documentation/frv/.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Rob Landley <rob@landley.net>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: linux-doc@vger.kernel.org
Meta core internal interrupts (from HWSTATMETA and friends) are vectored
onto the TR1 core trigger for the current thread. This is demultiplexed
in irq-metag.c to individual Linux IRQs for each internal interrupt.
External SoC interrupts (from HWSTATEXT and friends) are vectored onto
the TR2 core trigger for the current thread. This is demultiplexed in
irq-metag-ext.c to individual Linux IRQs for each external SoC interrupt.
The external irqchip has devicetree bindings for configuring the number
of irq banks and the type of masking available.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Dom Cobley <popcornmix@gmail.com>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-doc@vger.kernel.org
an SSD to be used as a cache in front of a slower device. Cache
tuning is delegated to interchangeable policy modules so these can
be developed independently of the mechanics needed to shuffle the
data around.
Other than that, kcopyd users acquire a throttling parameter, ioctl
buffer usage gets streamlined, more mempool reliance is reduced
and there are a few other bug fixes and tidy-ups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yXuO
-----END PGP SIGNATURE-----
Merge tag 'dm-3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper update from Alasdair G Kergon:
"The main addition here is a long-desired target framework to allow an
SSD to be used as a cache in front of a slower device. Cache tuning
is delegated to interchangeable policy modules so these can be
developed independently of the mechanics needed to shuffle the data
around.
Other than that, kcopyd users acquire a throttling parameter, ioctl
buffer usage gets streamlined, more mempool reliance is reduced and
there are a few other bug fixes and tidy-ups."
* tag 'dm-3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm: (30 commits)
dm cache: add cleaner policy
dm cache: add mq policy
dm: add cache target
dm persistent data: add bitset
dm persistent data: add transactional array
dm thin: remove cells from stack
dm bio prison: pass cell memory in
dm persistent data: add btree_walk
dm: add target num_write_bios fn
dm kcopyd: introduce configurable throttling
dm ioctl: allow message to return data
dm ioctl: optimize functions without variable params
dm ioctl: introduce ioctl_flags
dm: merge io_pool and tio_pool
dm: remove unused _rq_bio_info_cache
dm: fix limits initialization when there are no data devices
dm snapshot: add missing module aliases
dm persistent data: set some btree fn parms const
dm: refactor bio cloning
dm: rename bio cloning functions
...
This is an assorted set of stragglers into the merge window with driver
updates for qla2xxx, megaraid_sas, storvsc and ufs. It also includes pulls of
the uapi tree (all the remaining SCSI pieces) and the fcoe tree (updates to
fcoe and libfc)
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRMHJHAAoJEDeqqVYsXL0M9tAH/2YG3TCfy0RFAejGgLfX9OGH
6eFe71m7Z8nfIEneAnm5BuKjCx3QFRp5UFjJZdFHLP1Qv0TbpKs4FnZyeSGTxLQp
S1fZc5sTWmsb5qYxLaukKopC6sFx+hNI2dvB+rgKcd+nWy1RzG7lGqbS4CRNE76q
UNByqlfqJxn5cfQw7dg2zOUKlGaGL2jSyFf0QFXR2IZzO33PeyBPfKDFeJC6b+oc
XTy9MK9V5u6ne3XimDTU2hP4lPAsZaJtcqsv1Gvv2y+BHalQiPqfL6bZMvN3Zbfq
hfT+i2xnYy85858gxtyIhzHwU14zF7I0HEWiVpddsF9NDK7iNKvK8aWHaTs7qis=
=hvGQ
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is an assorted set of stragglers into the merge window with
driver updates for qla2xxx, megaraid_sas, storvsc and ufs.
It also includes pulls of the uapi tree (all the remaining SCSI
pieces) and the fcoe tree (updates to fcoe and libfc)"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (81 commits)
[SCSI] ufs: Separate PCI code into glue driver
[SCSI] ufs: Segregate PCI Specific Code
[SCSI] scsi: fix lpfc build when wmb() is defined as mb()
[SCSI] storvsc: Handle dynamic resizing of the device
[SCSI] storvsc: Restructure error handling code on command completion
[SCSI] storvsc: avoid usage of WRITE_SAME
[SCSI] aacraid: suppress two GCC warnings
[SCSI] hpsa: check for dma_mapping_error in hpsa_passthru ioctls
[SCSI] hpsa: reorganize error handling in hpsa_passthru_ioctl
[SCSI] hpsa: check for dma_mapping_error in hpsa_map_sg_chain_block
[SCSI] hpsa: Check for dma_mapping_error for all code paths using fill_cmd
[SCSI] hpsa: Check for dma_mapping_error in hpsa_map_one
[SCSI] dc395x: uninitialized variable in device_alloc()
[SCSI] Fix range check in scsi_host_dif_capable()
[SCSI] storvsc: Initialize the sglist
[SCSI] mpt2sas: Add support for OEM specific controller
[SCSI] ipr: Fix oops while resetting an ipr adapter
[SCSI] fnic: Fnic Trace Utility
[SCSI] fnic: New debug flags and debug log messages
[SCSI] fnic: fnic driver may hit BUG_ON on device reset
...
Tim found:
WARNING: at arch/x86/kernel/smpboot.c:324 topology_sane.isra.2+0x6f/0x80()
Hardware name: S2600CP
sched: CPU #1's llc-sibling CPU #0 is not on the same node! [node: 1 != 0]. Ignoring dependency.
smpboot: Booting Node 1, Processors #1
Modules linked in:
Pid: 0, comm: swapper/1 Not tainted 3.9.0-0-generic #1
Call Trace:
set_cpu_sibling_map+0x279/0x449
start_secondary+0x11d/0x1e5
Don Morris reproduced on a HP z620 workstation, and bisected it to
commit e8d1955258 ("acpi, memory-hotplug: parse SRAT before memblock
is ready")
It turns out movable_map has some problems, and it breaks several things
1. numa_init is called several times, NOT just for srat. so those
nodes_clear(numa_nodes_parsed)
memset(&numa_meminfo, 0, sizeof(numa_meminfo))
can not be just removed. Need to consider sequence is: numaq, srat, amd, dummy.
and make fall back path working.
2. simply split acpi_numa_init to early_parse_srat.
a. that early_parse_srat is NOT called for ia64, so you break ia64.
b. for (i = 0; i < MAX_LOCAL_APIC; i++)
set_apicid_to_node(i, NUMA_NO_NODE)
still left in numa_init. So it will just clear result from early_parse_srat.
it should be moved before that....
c. it breaks ACPI_TABLE_OVERIDE...as the acpi table scan is moved
early before override from INITRD is settled.
3. that patch TITLE is total misleading, there is NO x86 in the title,
but it changes critical x86 code. It caused x86 guys did not
pay attention to find the problem early. Those patches really should
be routed via tip/x86/mm.
4. after that commit, following range can not use movable ram:
a. real_mode code.... well..funny, legacy Node0 [0,1M) could be hot-removed?
b. initrd... it will be freed after booting, so it could be on movable...
c. crashkernel for kdump...: looks like we can not put kdump kernel above 4G
anymore.
d. init_mem_mapping: can not put page table high anymore.
e. initmem_init: vmemmap can not be high local node anymore. That is
not good.
If node is hotplugable, the mem related range like page table and
vmemmap could be on the that node without problem and should be on that
node.
We have workaround patch that could fix some problems, but some can not
be fixed.
So just remove that offending commit and related ones including:
f7210e6c4a ("mm/memblock.c: use CONFIG_HAVE_MEMBLOCK_NODE_MAP to
protect movablecore_map in memblock_overlaps_region().")
01a178a94e ("acpi, memory-hotplug: support getting hotplug info from
SRAT")
27168d38fa ("acpi, memory-hotplug: extend movablemem_map ranges to
the end of node")
e8d1955258 ("acpi, memory-hotplug: parse SRAT before memblock is
ready")
fb06bc8e5f ("page_alloc: bootmem limit with movablecore_map")
42f47e27e7 ("page_alloc: make movablemem_map have higher priority")
6981ec3114 ("page_alloc: introduce zone_movable_limit[] to keep
movable limit for nodes")
34b71f1e04 ("page_alloc: add movable_memmap kernel parameter")
4d59a75125 ("x86: get pg_data_t's memory from other node")
Later we should have patches that will make sure kernel put page table
and vmemmap on local node ram instead of push them down to node0. Also
need to find way to put other kernel used ram to local node ram.
Reported-by: Tim Gardner <tim.gardner@canonical.com>
Reported-by: Don Morris <don.morris@hp.com>
Bisected-by: Don Morris <don.morris@hp.com>
Tested-by: Don Morris <don.morris@hp.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=NKkW
-----END PGP SIGNATURE-----
Merge tag 'arc-v3.9-rc1-late' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull new ARC architecture from Vineet Gupta:
"Initial ARC Linux port with some fixes on top for 3.9-rc1:
I would like to introduce the Linux port to ARC Processors (from
Synopsys) for 3.9-rc1. The patch-set has been discussed on the public
lists since Nov and has received a fair bit of review, specially from
Arnd, tglx, Al and other subsystem maintainers for DeviceTree, kgdb...
The arch bits are in arch/arc, some asm-generic changes (acked by
Arnd), a minor change to PARISC (acked by Helge).
The series is a touch bigger for a new port for 2 main reasons:
1. It enables a basic kernel in first sub-series and adds
ptrace/kgdb/.. later
2. Some of the fallout of review (DeviceTree support, multi-platform-
image support) were added on top of orig series, primarily to
record the revision history.
This updated pull request additionally contains
- fixes due to our GNU tools catching up with the new syscall/ptrace
ABI
- some (minor) cross-arch Kconfig updates."
* tag 'arc-v3.9-rc1-late' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (82 commits)
ARC: split elf.h into uapi and export it for userspace
ARC: Fixup the current ABI version
ARC: gdbserver using regset interface possibly broken
ARC: Kconfig cleanup tracking cross-arch Kconfig pruning in merge window
ARC: make a copy of flat DT
ARC: [plat-arcfpga] DT arc-uart bindings change: "baud" => "current-speed"
ARC: Ensure CONFIG_VIRT_TO_BUS is not enabled
ARC: Fix pt_orig_r8 access
ARC: [3.9] Fallout of hlist iterator update
ARC: 64bit RTSC timestamp hardware issue
ARC: Don't fiddle with non-existent caches
ARC: Add self to MAINTAINERS
ARC: Provide a default serial.h for uart drivers needing BASE_BAUD
ARC: [plat-arcfpga] defconfig for fully loaded ARC Linux
ARC: [Review] Multi-platform image #8: platform registers SMP callbacks
ARC: [Review] Multi-platform image #7: SMP common code to use callbacks
ARC: [Review] Multi-platform image #6: cpu-to-dma-addr optional
ARC: [Review] Multi-platform image #5: NR_IRQS defined by ARC core
ARC: [Review] Multi-platform image #4: Isolate platform headers
ARC: [Review] Multi-platform image #3: switch to board callback
...
Pull MIPS updates from Ralf Baechle:
o Add basic support for the Mediatek/Ralink Wireless SoC family.
o The Qualcomm Atheros platform is extended by support for the new
QCA955X SoC series as well as a bunch of patches that get the code
ready for OF support.
o Lantiq and BCM47XX platform have a few improvements and bug fixes.
o MIPS has sent a few patches that get the kernel ready for the
upcoming microMIPS support.
o The rest of the series is made up of small bug fixes and cleanups
that relate to various parts of the MIPS code. The biggy in there is
a whitespace cleanup. After I was sent another set of whitespace
cleanup patches I decided it was the time to clean the whitespace
"issues" for once and and that touches many files below arch/mips/.
Fix up silly conflicts, mostly due to whitespace cleanups.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (105 commits)
MIPS: Quit exporting kernel internel break codes to uapi/asm/break.h
MIPS: remove broken conditional inside vpe loader code
MIPS: SMTC: fix implicit declaration of set_vi_handler
MIPS: early_printk: drop __init annotations
MIPS: Probe for and report hardware virtualization support.
MIPS: ath79: add support for the Qualcomm Atheros AP136-010 board
MIPS: ath79: add USB controller registration code for the QCA955X SoCs
MIPS: ath79: add PCI controller registration code for the QCA955X SoCs
MIPS: ath79: add WMAC registration code for the QCA955X SoCs
MIPS: ath79: register UART for the QCA955X SoCs
MIPS: ath79: add QCA955X specific glue to ath79_device_reset_{set, clear}
MIPS: ath79: add GPIO setup code for the QCA955X SoCs
MIPS: ath79: add IRQ handling code for the QCA955X SoCs
MIPS: ath79: add clock setup code for the QCA955X SoCs
MIPS: ath79: add SoC detection code for the QCA955X SoCs
MIPS: ath79: add early printk support for the QCA955X SoCs
MIPS: ath79: fix WMAC IRQ resource assignment
mips: reserve elfcorehdr
mips: Make sure kernel memory is in iomem
MIPS: ath79: use dynamically allocated USB platform devices
...
A simple cache policy that writes back all data to the origin.
This is used to decommission a dm cache by emptying it.
Signed-off-by: Heinz Mauelshagen <mauelshagen@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
A cache policy that uses a multiqueue ordered by recent hit
count to select which blocks should be promoted and demoted.
This is meant to be a general purpose policy. It prioritises
reads over writes.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add a target that allows a fast device such as an SSD to be used as a
cache for a slower device such as a disk.
A plug-in architecture was chosen so that the decisions about which data
to migrate and when are delegated to interchangeable tunable policy
modules. The first general purpose module we have developed, called
"mq" (multiqueue), follows in the next patch. Other modules are
under development.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Heinz Mauelshagen <mauelshagen@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
this patchset add the timeout-sec property to the following drivers:
orion_wdt, pnx4008_wdt, s3c2410_wdt and at91sam9_wdt.
The at91sam9_wdt is tested on evk-pr3,
the other drivers are compile tested only.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add support for watchdog drivers to initialize/set the timeout field
of the watchdog_device structure. The timeout field is initialised
either with the module timeout parameter value (if valid) or with the
timeout-sec dt property (if valid). If both are invalid the initial
value is unchanged.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Florian Fainelli