extcon-palmas must be child of palmas and expects parent's
drvdata to be valid. Check for non NULL parent drvdata and
fail if it is NULL. Not doing so will result in a NULL
pointer dereference later in the probe() parent drvdata
is NULL (e.g. misplaced extcon-palmas node in device tree).
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Aligning all block comments in extcon subsystem as per linux coding style.
Found using checkpatch.pl script.
Signed-off-by: Srikant Ritolia <s.ritolia@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Function get_zeroed_page() returns a NULL pointer if there is no enough
memory. In function extcon_sync(), it returns 0 if the call to
get_zeroed_page() fails. The return value 0 indicates success in the
context, which is incosistent with the execution status. This patch
fixes the bug by returning -ENOMEM.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188611
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Currently we handle both old style GPIO and new style GPIOD differently
simplify this slightly by converting the old style GPIO to a GPIOD and
just using that from then on.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
No dramatic changes are found in this development cycle, but as usual,
many commits are applied in a wide range of drivers.
Most of big changes are in ASoC, where a few bits of framework work
and quite a lot of cleanups and improvements to existing code have
been done. The rest are usual stuff, a few HD-audio and USB-audio
quirks and fixes, as well as the drop of kthread usages in the whole
subsystem.
Below are some highlights:
ASoC:
- Support for stereo DAPM controls
- Some initial work on the of-graph sound card
- regmap conversions of the remaining AC'97 drivers
- A new version of the topology ABI; this should be backward compatible
- Updates / cleanups of rsnd, sunxi, sti, nau8825, samsung, arizona,
Intel skylake, atom-sst
- New drivers for Cirrus Logic CS42L42, Qualcomm MSM8916-WCD, and
Realtek RT5665
USB-audio:
- Yet another race fix at disconnection
- Tolerated packet size calculation for some Android devices
- Quirks for Axe-Fx II, QuickCam, TEAC 501/503
HD-audio:
- Improvement of Dell pin fixup mapping
- Quirks for HP Z1 Gen3, Alienware 15 R2 2016 and ALC622 headset mic
Misc:
- Replace all kthread usages with simple works
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=WZeb
-----END PGP SIGNATURE-----
Merge tag 'sound-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"No dramatic changes are found in this development cycle, but as usual,
many commits are applied in a wide range of drivers.
Most of big changes are in ASoC, where a few bits of framework work
and quite a lot of cleanups and improvements to existing code have
been done. The rest are usual stuff, a few HD-audio and USB-audio
quirks and fixes, as well as the drop of kthread usages in the whole
subsystem.
Below are some highlights:
ASoC:
- support for stereo DAPM controls
- some initial work on the of-graph sound card
- regmap conversions of the remaining AC'97 drivers
- a new version of the topology ABI; this should be backward
compatible
- updates / cleanups of rsnd, sunxi, sti, nau8825, samsung, arizona,
Intel skylake, atom-sst
- new drivers for Cirrus Logic CS42L42, Qualcomm MSM8916-WCD, and
Realtek RT5665
USB-audio:
- yet another race fix at disconnection
- tolerated packet size calculation for some Android devices
- quirks for Axe-Fx II, QuickCam, TEAC 501/503
HD-audio:
- improvement of Dell pin fixup mapping
- quirks for HP Z1 Gen3, Alienware 15 R2 2016 and ALC622 headset mic
Misc:
- replace all kthread usages with simple works"
* tag 'sound-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (296 commits)
ALSA: hiface: Fix M2Tech hiFace driver sampling rate change
ALSA: usb-audio: Eliminate noise at the start of DSD playback.
ALSA: usb-audio: Add native DSD support for TEAC 501/503 DAC
ASoC: wm_adsp: wm_adsp_buf_alloc should use kfree in error path
ASoC: topology: avoid uninitialized kcontrol_type
ALSA: usb-audio: Add QuickCam Communicate Deluxe/S7500 to volume_control_quirks
ALSA: usb-audio: add implicit fb quirk for Axe-Fx II
ASoC: zte: spdif: correct ZX_SPDIF_CLK_RAT define
ASoC: zte: spdif and i2s drivers are not zx296702 specific
ASoC: rsnd: setup BRGCKR/BRRA/BRRB when starting
ASoC: rsnd: enable/disable ADG when suspend/resume timing
ASoC: rsnd: tidyup ssi->usrcnt counter check in hw_params
ALSA: cs46xx: add a new line
ASoC: Intel: update bxt_da7219_max98357a to support quad ch dmic capture
ASoC: nau8825: disable sinc filter for high THD of ADC
ALSA: usb-audio: more tolerant packetsize
ALSA: usb-audio: avoid setting of sample rate multiple times on bus
ASoC: cs35l34: Simplify the logic to set CS35L34_MCLK_CTL setting
ALSA: hda - Gate the mic jack on HP Z1 Gen3 AiO
ALSA: hda: when comparing pin configurations, ignore assoc in addition to seq
...
The name of a codec pin can have an optional prefix string, which is
defined by the SoC machine driver. The snd_soc_dapm_x_pin functions
take the fully-specified name including the prefix and so the existing
code would fail to find the pin if the audio machine driver had added
a prefix.
Switch to using the snd_soc_component_x_pin equivalent functions that
take a specified SoC component and automatically add the name prefix to
the provided pin name.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver can now work with both ID and VBUS pins or either one of
them.
There can be the following 3 cases
1) Both ID and VBUS GPIOs are available:
ID = LOW -> USB_HOST active, USB inactive
ID = HIGH -> USB_HOST inactive, USB state is same as VBUS.
2) Only ID GPIO is available:
ID = LOW -> USB_HOST active, USB inactive
ID = HIGH -> USB_HOST inactive, USB active
3) Only VBUS GPIO is available:
VBUS = LOW -> USB_HOST inactive, USB inactive
VBUS = HIGH -> USB_HOST inactive, USB active
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The driver was changed after submission to use the new style APIs
like extcon_set_state(). Unfortunately, that only sets the state,
and doesn't notify any consumers that the cable state has
changed. Use extcon_set_state_sync() here instead so that we
notify cable consumers of the state change. This fixes USB
host-device role switching on the db8074 platform.
Fixes: 38085c987f ("extcon: Add support for qcom SPMI PMIC USB id detection hardware")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Some Qualcomm PMICs have a misc device that performs USB id pin
detection via an interrupt. When the interrupt triggers, we
should read the interrupt line to see if it has gone high or low.
If the interrupt is low then the ID pin is grounded, and if the
interrupt is high then the ID pin is being held high.
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
[cw00.choi: Edited the driver description and added the author information]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch alters the renamed extcon API to set the state of the external
connectors instead of deprecated extcon_set_cable_state_().
Because the patch[1] modifies the function name to maintain the function
naming pattern.
- extcon_set_cable_state_() -> extcon_set_state_sync()
- extcon_get_cable_state_() -> extcon_get_state()
[1] https://lkml.org/lkml/2016/8/4/729
- extcon: Rename the extcon_set/get_state() to maintain the function naming pattern
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Roger Quadros <rogerq@ti.com>
This patch fixes the spelling mistake in dev_dbg messages.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
[cw00.choi: Modify the patch title/description]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Change my email address to kernel.org instead of Samsung one for the
purpose of any future contact. The copyrights remain untouched and are
attributed to Samsung.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patchs add the new EXTCON_CHG_WPT for Wireless Power Transfer[1].
The Wireless Power Transfer is the transmission of electronical energy
from a power source. The EXTCON_CHG_WPT has the EXTCON_TYPE_CHG.
[1] https://en.wikipedia.org/wiki/Wireless_power_transfer
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch adds the new EXTCON_DISP_HMD id for Head-mounted Display[1] device.
The HMD device is usually for USB connector type So, the HMD connector
has the two extcon types of both EXTCON_TYPE_DISP and EXTCON_TYPE_USB.
[1] https://en.wikipedia.org/wiki/Head-mounted_display
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add EXTCON_DISP_DP for the Display external connector. For Type-C
connector the DisplayPort can work as an Alternate Mode(VESA DisplayPort
Alt Mode on USB Type-C Standard). The Type-C support both normal
and flipped orientation, so add a property to extcon.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
This patch adds the synchronization extcon APIs to support the notifications
for both state and property. When extcon_*_sync() functions is called,
the extcon informs the information from extcon provider to extcon client.
The extcon driver may need to change the both state and multiple properties
at the same time. After setting the data of a external connector,
the extcon send the notification to client driver with the extcon_*_sync().
The list of new extcon APIs as following:
- extcon_sync() : Send the notification for each external connector to
synchronize the information between extcon provider driver
and extcon client driver.
- extcon_set_state_sync() : Set the state of external connector with noti.
- extcon_set_property_sync() : Set the property of external connector with noti.
For example,
case 1, change the state of external connector and synchronized the data.
extcon_set_state_sync(edev, EXTCON_USB, 1);
case 2, change both the state and property of external connector
and synchronized the data.
extcon_set_state(edev, EXTCON_USB, 1);
extcon_set_property(edev, EXTCON_USB, EXTCON_PROP_USB_VBUS 1);
extcon_sync(edev, EXTCON_USB);
case 3, change the property of external connector and synchronized the data.
extcon_set_property(edev, EXTCON_USB, EXTCON_PROP_USB_VBUS, 0);
extcon_sync(edev, EXTCON_USB);
case 4, change the property of external connector and synchronized the data.
extcon_set_property_sync(edev, EXTCON_USB, EXTCON_PROP_USB_VBUS, 0);
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
This patch just renames the existing extcon_get/set_cable_state_()
as following because of maintaining the function naming pattern
like as extcon APIs for property.
- extcon_set_cable_state_() -> extcon_set_state()
- extcon_get_cable_state_() -> extcon_get_state()
But, this patch remains the old extcon_set/get_cable_state_() functions
to prevent the build break. After altering new APIs, remove the old APIs.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
This patch adds the support of the property capability setting. This function
decides the supported properties of each external connector on extcon provider
driver.
Ths list of new extcon APIs to get/set the capability of property as following:
- int extcon_get_property_capability(struct extcon_dev *edev,
unsigned int id, unsigned int prop);
- int extcon_set_property_capability(struct extcon_dev *edev,
unsigned int id, unsigned int prop);
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
This patch support the extcon property for the external connector
because each external connector might have the property according to
the H/W design and the specific characteristics.
- EXTCON_PROP_USB_[property name]
- EXTCON_PROP_CHG_[property name]
- EXTCON_PROP_JACK_[property name]
- EXTCON_PROP_DISP_[property name]
Add the new extcon APIs to get/set the property value as following:
- int extcon_get_property(struct extcon_dev *edev, unsigned int id,
unsigned int prop,
union extcon_property_value *prop_val)
- int extcon_set_property(struct extcon_dev *edev, unsigned int id,
unsigned int prop,
union extcon_property_value prop_val)
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
This patch adds the new extcon type to group the each connecotr
into following five category. This type would be used to handle
the connectors as a group unit instead of a connector unit.
- EXTCON_TYPE_USB : USB connector
- EXTCON_TYPE_CHG : Charger connector
- EXTCON_TYPE_JACK : Jack connector
- EXTCON_TYPE_DISP : Display connector
- EXTCON_TYPE_MISC : Miscellaneous connector
Also, each external connector is possible to belong to one more extcon type.
In caes of EXTCON_CHG_USB_SDP, it have the EXTCON_TYPE_CHG and EXTCON_TYPE_USB.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
This patch fixes below compilation warning:-
drivers/extcon/extcon.c: In function extcon_register_notifier:
drivers/extcon/extcon.c:455:6: warning: idx may be used uninitialized in this function [-Wmaybe-uninitialized]
if (idx >= 0) {
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
[cw00.choi : Modify the patch title using the a captical letter for first char]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch restrict the usage of extcon_update_state() in the extcon
core because the extcon_update_state() use the bit masking to change
the state of external connector. When this function is used in device drivers,
it may occur the probelm with the handling mistake of bit masking.
Also, this patch removes the extcon_get/set_state() functions because these
functions use the bit masking which is reluctant way. Instead, extcon
provides the extcon_set/get_cable_state_() functions.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch removes the state_store() which change the state of external
connectors with bit masking on user-space. It is wrong access to modify
the change the state of external connectors.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch removes the usage of extcon_set_state() because it uses
the bit masking to change the state of external connectors. The extcon framework
should handle the state by extcon_set_cable_state_() with extcon id.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch removes the usage of extcon_set_state() because it uses the bit
masking to change the state of external connectors. The extcon framework
should handle the state by extcon_set/get_cable_state_() with extcon id.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch remvoes the usage of extcon_update_state() because
the extcon_update_state() use directly the bit masking calculation
to change the state of external connector without the unique id of
external connector. It makes the code diffcult to read it.
So, this patch uses the extcon_set_cable_state_() instead.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
There is no need for a semi-colon at the end of a switch statement so
remove it.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Sometimes drivers may call this API and expect it to fail because
the extcon they're looking for is optional. Let's move these
prints to debug level so it doesn't look like there's a problem
when there isn't one.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Update cable state during boot to avoid any missing
external cable events occurred before driver initialisation.
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patchs add the new EXTCON_CHG_WPT for Wireless Power Transfer[1].
The Wireless Power Transfer is the transmission of electronical energy
from a power source. The EXTCON_CHG_WPT has the EXTCON_TYPE_CHG.
[1] https://en.wikipedia.org/wiki/Wireless_power_transfer
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch adds the new EXTCON_DISP_HMD id for Head-mounted Display[1] device.
The HMD device is usually for USB connector type So, the HMD connector
has the two extcon types of both EXTCON_TYPE_DISP and EXTCON_TYPE_USB.
[1] https://en.wikipedia.org/wiki/Head-mounted_display
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add EXTCON_DISP_DP for the Display external connector. For Type-C
connector the DisplayPort can work as an Alternate Mode(VESA DisplayPort
Alt Mode on USB Type-C Standard). The Type-C support both normal
and flipped orientation, so add a property to extcon.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
This patch adds the synchronization extcon APIs to support the notifications
for both state and property. When extcon_*_sync() functions is called,
the extcon informs the information from extcon provider to extcon client.
The extcon driver may need to change the both state and multiple properties
at the same time. After setting the data of a external connector,
the extcon send the notification to client driver with the extcon_*_sync().
The list of new extcon APIs as following:
- extcon_sync() : Send the notification for each external connector to
synchronize the information between extcon provider driver
and extcon client driver.
- extcon_set_state_sync() : Set the state of external connector with noti.
- extcon_set_property_sync() : Set the property of external connector with noti.
For example,
case 1, change the state of external connector and synchronized the data.
extcon_set_state_sync(edev, EXTCON_USB, 1);
case 2, change both the state and property of external connector
and synchronized the data.
extcon_set_state(edev, EXTCON_USB, 1);
extcon_set_property(edev, EXTCON_USB, EXTCON_PROP_USB_VBUS 1);
extcon_sync(edev, EXTCON_USB);
case 3, change the property of external connector and synchronized the data.
extcon_set_property(edev, EXTCON_USB, EXTCON_PROP_USB_VBUS, 0);
extcon_sync(edev, EXTCON_USB);
case 4, change the property of external connector and synchronized the data.
extcon_set_property_sync(edev, EXTCON_USB, EXTCON_PROP_USB_VBUS, 0);
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
This patch just renames the existing extcon_get/set_cable_state_()
as following because of maintaining the function naming pattern
like as extcon APIs for property.
- extcon_set_cable_state_() -> extcon_set_state()
- extcon_get_cable_state_() -> extcon_get_state()
But, this patch remains the old extcon_set/get_cable_state_() functions
to prevent the build break. After altering new APIs, remove the old APIs.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
This patch adds the support of the property capability setting. This function
decides the supported properties of each external connector on extcon provider
driver.
Ths list of new extcon APIs to get/set the capability of property as following:
- int extcon_get_property_capability(struct extcon_dev *edev,
unsigned int id, unsigned int prop);
- int extcon_set_property_capability(struct extcon_dev *edev,
unsigned int id, unsigned int prop);
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
This patch support the extcon property for the external connector
because each external connector might have the property according to
the H/W design and the specific characteristics.
- EXTCON_PROP_USB_[property name]
- EXTCON_PROP_CHG_[property name]
- EXTCON_PROP_JACK_[property name]
- EXTCON_PROP_DISP_[property name]
Add the new extcon APIs to get/set the property value as following:
- int extcon_get_property(struct extcon_dev *edev, unsigned int id,
unsigned int prop,
union extcon_property_value *prop_val)
- int extcon_set_property(struct extcon_dev *edev, unsigned int id,
unsigned int prop,
union extcon_property_value prop_val)
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
This patch adds the new extcon type to group the each connecotr
into following five category. This type would be used to handle
the connectors as a group unit instead of a connector unit.
- EXTCON_TYPE_USB : USB connector
- EXTCON_TYPE_CHG : Charger connector
- EXTCON_TYPE_JACK : Jack connector
- EXTCON_TYPE_DISP : Display connector
- EXTCON_TYPE_MISC : Miscellaneous connector
Also, each external connector is possible to belong to one more extcon type.
In caes of EXTCON_CHG_USB_SDP, it have the EXTCON_TYPE_CHG and EXTCON_TYPE_USB.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
This patch fixes below compilation warning:-
drivers/extcon/extcon.c: In function extcon_register_notifier:
drivers/extcon/extcon.c:455:6: warning: idx may be used uninitialized in this function [-Wmaybe-uninitialized]
if (idx >= 0) {
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
[cw00.choi : Modify the patch title using the a captical letter for first char]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch restrict the usage of extcon_update_state() in the extcon
core because the extcon_update_state() use the bit masking to change
the state of external connector. When this function is used in device drivers,
it may occur the probelm with the handling mistake of bit masking.
Also, this patch removes the extcon_get/set_state() functions because these
functions use the bit masking which is reluctant way. Instead, extcon
provides the extcon_set/get_cable_state_() functions.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch removes the state_store() which change the state of external
connectors with bit masking on user-space. It is wrong access to modify
the change the state of external connectors.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch removes the usage of extcon_set_state() because it uses
the bit masking to change the state of external connectors. The extcon framework
should handle the state by extcon_set_cable_state_() with extcon id.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch removes the usage of extcon_set_state() because it uses the bit
masking to change the state of external connectors. The extcon framework
should handle the state by extcon_set/get_cable_state_() with extcon id.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch remvoes the usage of extcon_update_state() because
the extcon_update_state() use directly the bit masking calculation
to change the state of external connector without the unique id of
external connector. It makes the code diffcult to read it.
So, this patch uses the extcon_set_cable_state_() instead.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
There is no need for a semi-colon at the end of a switch statement so
remove it.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Sometimes drivers may call this API and expect it to fail because
the extcon they're looking for is optional. Let's move these
prints to debug level so it doesn't look like there's a problem
when there isn't one.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Update cable state during boot to avoid any missing
external cable events occurred before driver initialisation.
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
adding suspend and resume funtionality for extcon-adc-jack
driver to configure system wake up for extcon events,
also adding support to enable/disable system wakeup
through flag wakeup_source based on platform requirement.
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Splitting the resource-managed functions into a separate module
means that the extcon core now fails to build because the internal
"extcon_dev_allocate" symbol is not exported:
ERROR: extcon_dev_allocate [drivers/extcon/devres.ko] undefined!
My guess is that the intention was not to have two separate
modules (which could be fixed by adding an export, plus the
normal MODULE_AUTHOR/MODULE_LICENSE/... fields), but have two
source files in the same module.
This fixes the Makefile accordingly, making the name of the
module extcon_core.ko, which is created from building both
extcon.c and devres.c.
Fixes: b225d00f3a ("extcon: Split out the resource-managed functions from extcon core")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch adds the resource-managed functions for register/unregister
the extcon notifier with the id of each external connector. This function
will make it easy to handle the extcon notifier.
- int devm_extcon_register_notifier(struct device *dev,
struct extcon_dev *edev, unsigned int id,
struct notifier_block *nb);
- void devm_extcon_unregister_notifier(struct device *dev,
struct extcon_dev *edev, unsigned int id,
struct notifier_block *nb);
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch moves the struct extcon_cable because that should
be only handled by extcon core. There are no reason to publish
the internal structure.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
If we call extcon_register_notifier() with the wrong cable type,
it blows up with an oops instead of returning an error code.
Let's be nice and fail gracefully given that the consumer might
not know if the cable is supported by the extcon provider.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
GPIO resource could be retrieved through APCI as well.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Felipe Balbi <balbi@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This is needed to handle the GPIO connected USB ID pin found on
Intel Baytrail devices.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Felipe Balbi <balbi@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Pin state might have changed during suspend/resume while
our interrupts were disabled and if device doesn't support wakeup.
Scan for change during resume for such case.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Switch to use PM wakeirq APIs which automates wakeup IRQs
enabling/disabling and so allows to make code simpler.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
If USB cable is connected prior to boot, we don't get any interrupts
so we must manually check the VBUS state and report it during probe.
If we don't do it then USB controller will never know that peripheral
cable was connected till the user unplugs and replugs the cable.
Fixes: b7aad8e268 ("extcon: palmas: Add the support for VBUS detection by using GPIO")
Cc: stable@vger.kernel.org
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch removes the deprecated extcon functions using string type
to identify the type of external connector. The Commit 2a9de9c0f0
("extcon: Use the unique id for external connector instead of string)
uses the unique id to separate the type of external connector instead of
string name.
- extcon_register_interest()
- extcon_unregister_interest()
- extcon_set_cable_state()
- extcon_get_cable_state()
And, extcon_register_interest() finds the first extcon device to include the
requested external connector from extcon client device and then register the
notifier if extcon device argument is NULL. Instead, extcon_register_notifier()
supports this feature.
But, this patch remains the deprecatd function definition to prevent
the build break.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Palmas extcon IRQs are nested threaded and wired to the Palmas
interrupt controller. So, this flag is not required for nested
IRQs anymore, since commit 3c646f2c6a ("genirq: Don't suspend
nested_thread irqs over system suspend") was merged. However, the
fix in commit ae64e42cc2 ("extcon: palmas: Drop IRQF_EARLY_RESUME
flag") missed a stray flag causing the following crash on resume on
BeagleBoard-X15 platform:
[ 53.670141] Unhandled fault: imprecise external abort (0x1406) at 0x00000000
[..]
[ 53.670141] [<c04ae734>] (omap_set_gpio_triggering) from [<c04aeb94>] (omap_gpio_unmask_irq+0xc0/0xc4)
[ 53.670141] [<c04aeb94>] (omap_gpio_unmask_irq) from [<c01a0b88>] (irq_enable+0x30/0x44)
[ 53.670141] [<c01a0b88>] (irq_enable) from [<c019ebd8>] (__enable_irq+0x54/0x78)
[ 53.670141] [<c019ebd8>] (__enable_irq) from [<c01a4e60>] (resume_irqs+0xe8/0x100)
[ 53.670141] [<c01a4e60>] (resume_irqs) from [<c0514840>] (syscore_resume+0x94/0x298)
[ 53.670141] [<c0514840>] (syscore_resume) from [<c01981cc>] (suspend_devices_and_enter+0x790/0x9e4)
[ 53.670141] [<c01981cc>] (suspend_devices_and_enter) from [<c0198a60>] (pm_suspend+0x640/0x75c)
[ 53.670141] [<c0198a60>] (pm_suspend) from [<c0196bec>] (state_store+0x64/0xb8)
[ 53.670141] [<c0196bec>] (state_store) from [<c0307944>] (kernfs_fop_write+0xc0/0x1bc)
[ 53.670141] [<c0307944>] (kernfs_fop_write) from [<c028acb0>] (__vfs_write+0x1c/0xd8)
[ 53.670141] [<c028acb0>] (__vfs_write) from [<c028bba0>] (vfs_write+0x90/0x16c)
[ 53.670141] [<c028bba0>] (vfs_write) from [<c028c8c0>] (SyS_write+0x44/0x9c)
[ 53.670141] [<c028c8c0>] (SyS_write) from [<c0107840>] (ret_fast_syscall+0x0/0x1c)
[..]
Fixes: ae64e42cc2 ("extcon: palmas: Drop IRQF_EARLY_RESUME flag")
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Palams extcon IRQs are nested threaded and wired to the Palmas
inerrupt controller. So, this flag is not required for nested irqs
anymore, since commit 3c646f2c6a ("genirq: Don't suspend
nested_thread irqs over system suspend") was merged.
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch support for VBUS detection by using GPIO pin.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
The info->status[] array has 3 elements. We are using size
MAX77843_MUIC_IRQ_NUM (16) instead of MAX77843_MUIC_STATUS_NUM (3) as
intended.
Fixes: 135d9f7d13 ('extcon: max77843: Clear IRQ bits state before request IRQ')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[cw00.choi: Modify the patch title]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
We should be using the helper functions to lock the DAPM mutex not
accessing it directly. There are no ill effects of this as the moment
but it is best practice, and the implementation could be changed in the
future.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch adds the new EXTCON_CHG_USB_SDP connector to support SDP (Standard
Downstream Port) USB charging port. The commit 11eecf910b ("extcon: Modify
the id and name of external connector") add the new EXTCON_CHG_USB_SDP
connector which support the both data transfer and usb charging at the same
time.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch fixes the typo in comment of extcon-gpio.c driver.
- 'interrput' -> 'interrupt'
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Maxim Integrated MAX3355E chip integrates a charge pump and comparators to
enable a system with an integrated USB OTG dual-role transceiver to
function as an USB OTG dual-role device. In addition to sensing/controlling
Vbus, the chip also passes thru the ID signal from the USB OTG connector.
On some Renesas boards, this signal is just fed into the SoC thru a GPIO
pin -- there's no real OTG controller, only host and gadget USB controllers
sharing the same USB bus; however, we'd like to allow host or gadget
drivers to be loaded depending on the cable type, hence the need for the
MAX3355 extcon driver. The Vbus status signals are also wired to GPIOs
(however, we aren't currently interested in them), the OFFVBUS# signal is
controlled by the host controllers, there's also the SHDN# signal wired to
a GPIO, it should be driven high for the normal operation.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
[cw00.choi: Add the GPIOLIB dependency]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The function can return negative values, so its result should
be assigned to signed variable.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The function can return negative values, so its result should
be assigned to signed variable.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The function can return negative values, so its result should
be assigned to signed variable.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add device bindings to support configuring the jack detection
configurations. Each configuration needs to specify the connection of
the mic det pins, which micbias should be used and the value of the
micd polarity GPIO required to activate that configuration.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch adds IRQF_ONESHOT if no primary handler is provided for request
threaded irq.
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add time units of -ms (milliseconds) to wlf,micd-timeout.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Update the name for the second jack detection pin binding to be a little
less confusing.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Some Arizona devices have the option to use the GPIO5 pin as a second
jack detection pin. This patch adds device bindings to specify to the
driver that it should use this pin. Note that the second jack detection
pin is hard wired in the chip so can only be enabled through the
binding, rather than a pin being specified.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
By default the driver expects the jackdet pin to be pulled low when a
jack is inserted. This patch adds a device binding that allows the user
to specify that the jackdet pin will be pulled high when a jack is
inserted.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The switch is generally used in conjunction with the MICDET clamp to
suppress pops and clicks associated with jack insertion. This patch adds
a binding that allows the user to select the mode of operation for this
switch.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add a simple boolean binding to turn on and off the use of ADC
microphone detection mode to determine 3/4 pole jack.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch modifies the id and name of external connector with the
additional prefix to clarify both attribute and meaning of external
connector as following:
- EXTCON_CHG_* mean the charger connector.
- EXTCON_JACK_* mean the jack connector.
- EXTCON_DISP_* mean the display port connector.
Following table show the new name of external connector with old name:
--------------------------------------------------
Old extcon name | New extcon name |
--------------------------------------------------
EXTCON_TA | EXTCON_CHG_USB_DCP |
EXTCON_CHARGE_DOWNSTREAM| EXTCON_CHG_USB_CDP |
EXTCON_FAST_CHARGER | EXTCON_CHG_USB_FAST |
EXTCON_SLOW_CHARGER | EXTCON_CHG_USB_SLOW |
--------------------------------------------------
EXTCON_MICROPHONE | EXTCON_JACK_MICROPHONE |
EXTCON_HEADPHONE | EXTCON_JACK_HEADPHONE |
EXTCON_LINE_IN | EXTCON_JACK_LINE_IN |
EXTCON_LINE_OUT | EXTCON_JACK_LINE_OUT |
EXTCON_VIDEO_IN | EXTCON_JACK_VIDEO_IN |
EXTCON_VIDEO_OUT | EXTCON_JACK_VIDEO_OUT |
EXTCON_SPDIF_IN | EXTCON_JACK_SPDIF_IN |
EXTCON_SPDIF_OUT | EXTCON_JACK_SPDIF_OUT |
--------------------------------------------------
EXTCON_HMDI | EXTCON_DISP_HDMI |
EXTCON_MHL | EXTCON_DISP_MHL |
EXTCON_DVI | EXTCON_DISP_DVI |
EXTCON_VGA | EXTCON_DISP_VGA |
--------------------------------------------------
And, when altering the name of USB charger connector, EXTCON refers to the
"Battery Charging v1.2 Spec and Adopters Agreement"[1] to use the standard
name of USB charging port as following. Following name of USB charging port
are already used in power_supply subsystem. We chan check it on patch[2].
- EXTCON_CHG_USB_SDP /* Standard Downstream Port */
- EXTCON_CHG_USB_DCP /* Dedicated Charging Port */
- EXTCON_CHG_USB_CDP /* Charging Downstream Port */
- EXTCON_CHG_USB_ACA /* Accessory Charger Adapter */
[1] www.usb.org/developers/docs/devclass_docs/BCv1.2_070312.zip
[2] commit 85efc8a18c ("power_supply: Add types for USB chargers")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[ckeepax: For the Arizona changes]
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
This patch uses the descriptor-based GPIO interface (gpiod_* API) instead of
legacy gpio_* API and add the internal gpio_extcon_init() to handle
all gpio-related tasks.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch fixes the minor coding style about indentation and removes the
unused fields from struct gpio_extcon_platform_data.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The commit 2a9de9c0 ("extcon: Use the unique id for external connector instead
of string") defines the unique id of each external connector to identify the
type of external connector instead of string name. So, devm_extcon_dev_allocate()
should include the second parameter (unsigned int *supported_cable). This patch
adds the supported_cable parameter which is passed by platform data.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
There are duplicate data between struct gpio_extcon_data and struct
gpio_extcon_platform_data. This patch removes them from struct gpio_extcon_data.
Instead, this patch add pdata field to struct gpio_extcon_data.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch reorders the default statement to remove unnecessary warning message
when info->hpdet_ip_version is higher than 2.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
This patch adds support for the WM8998 and WM1814 codecs.
These use the same IP version as WM5110 but have different
clamp control.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Use resource managed functions devm_usb_get_phy and
devm_gpio_request to make error path simpler. To be
compatible the change, various gotos are replaced
with direct returns and unnecessary label
gpio_req_failed is dropped.
Also, remove function axp288_extcon_remove as it is
now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The I2C core always reports the MODALIAS uevent as "i2c:<modalias>"
regardless of the mechanism that was used to register the device
(i.e: OF or board code) and the table that is used later to match
the driver with the device (i.e: I2C id table or OF match table).
So drivers needs to export the I2C id table and this be built into
the module or udev won't have the necessary information to autoload
the needed driver module when the device is added.
But this means that OF-only drivers needs to have both OF and I2C id
tables that have to be kept in sync and also the dev node compatible
manufacturer prefix is stripped when reporting the MODALIAS. Which can
lead to issues if two vendors use the same I2C device name for example.
To avoid the above, the I2C core behavior may be changed in the future
to not require an SPI device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table even when
is unused now to prevent breaking module loading when the core changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Whilst the jack is connected we disable the jack detection debounce to
ensure as quick as possible a detection of jack removal. However, it is
only safe to disable the jack debounce whilst the jack is connected if
using the micd clamp or the jack is not inverted. Otherwise spurious
interrupts might be generated when we re-enable the debounce.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Currently we only use the microphone clamp IRQ if GPIO5 is being used as
a second jack detection pin. But we should be using it on any system
where the clamp is available. This patch updates the driver to do so.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The polarity of MICD_CLAMP_STS does not change when different clamp
modes are used, this patch corrects this issue.
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
If the TST_CAP_SEL bits aren't set correctly on wm5110/8280 there will
be a 100k load along side the headphones, which will affect the accurary
towards the very top of the detection range. This patch sets those bits.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The switch is typically used in conjunction with the MICDET clamp in
order to suppress pops and clicks associated with jack insertion.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Newer devices give users the option to make the 3/4 pole jack
determination using a software comparison rather than a hardware one.
This patch adds support for this functionality.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
is_extcon_changed should only check the idx-th bit of new, not
the entirety of new when setting attached.
This fixes extcon sending notifications that a cable was inserted when
it gets removed while another cable is still connected.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The biggest changes in the core this time around have been some
refactorings that move us towards being able to drop the list of
regulators maintained by the core and instead just use the driver model
list maintained for the class devices for regulators which will make the
code smaller and avoid some potential bugs. Otherwise another fairly
quiet release for the regulator API, highlights include:
- A new API for setting voltages based on a minimum, target, maximum
triplet.
- Support for continuous voltage ranges rather than tables of explicit
steps in the PWM regulator, requiring less explicit configuration.
- New driver support for Dialog DA9215, Maxim 77843, Mediatek MT6311
and Qualcomm RPM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV5DCWAAoJECTWi3JdVIfQDgYH/3mNwtRcwslt8M1L8lzRVyf1
gRrJY5r4EUOcqqsLnQvDHdjgO2yowEolEd3Hd/GElZqzeFgwXaQ62kHwgqnvOt9k
O0l99FbU6ECpB56tSENrV1lfvBTlld9bEhq9NhxvNiWAdpGPqIcjvXfSH28GssJ0
NGr4Yt/A1DG6GsOWxKSODX56WJXJn4emKx3vHH+leUClNWwQVK6JunTmj5IPKLxW
K94Ke41L3JgAy18TLqvFNlTAC22QaHFaM8ul9v7gnPW+S8Bx15MCQz16rMkGViZV
c/DyCu69qCVFLI1svRrvB5oq700QT0GT6jANCVmw+CrkIkESwjS39kX861H6hk8=
=vrVx
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The biggest changes in the core this time around have been some
refactorings that move us towards being able to drop the list of
regulators maintained by the core and instead just use the driver
model list maintained for the class devices for regulators which will
make the code smaller and avoid some potential bugs.
Otherwise another fairly quiet release for the regulator API,
highlights include:
- a new API for setting voltages based on a minimum, target, maximum
triplet
- support for continuous voltage ranges rather than tables of
explicit steps in the PWM regulator, requiring less explicit
configuration
- new driver support for Dialog DA9215, Maxim 77843, Mediatek MT6311
and Qualcomm RPM"
* tag 'regulator-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (70 commits)
regulator: mt6311: fix platform_no_drv_owner.cocci warnings
regulator: ltc3589: Remove unnecessary MODULE_ALIAS()
regulator: ad5398: Remove unnecessary MODULE_ALIAS()
regulator: pfuze100: Remove unnecessary MODULE_ALIAS()
regulator: core: use debug level print in regulator_check_drms
regulator: lp872x: handle error case
regulator: lp872x: use the private data instead of updating I2C device platform data
regulator: isl9305: Export OF module alias information
regulators: max77693: register driver earlier to avoid deferred probe
regulator: qcom_smd: Set n_voltages for pm8941_lnldo
regulator: core: Use IS_ERR_OR_NULL()
regulator: core: Define regulator_set_voltage_triplet()
regulator: Regulator driver for the Qualcomm RPM
regulator: pbias: Fix broken pbias disable functionality
regulator: core: Spelling fix
regulator: core: Use class device list for regulator_list in late init
regulator: core: Move more deallocation into class unregister
regulator: core: Reduce rdev locking region when releasing regulator
Input: Remove the max77843 haptic driver
Input: max77693: Add support for Maxim 77843
...
With commit b17d1bf16c ("gpio: make flags mandatory for gpiod_get functions")
it becomes necessary to pass the flags argument. And this patch adds the gpio
header file to fix the build breakage when build testing with random
configuration files.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Some palmas based chip variants do not have OTG based ID logic.
For these variants we rely on GPIO based USB ID detection.
These chips do have VBUS comparator for VBUS detection so we
continue to use the old way of detecting VBUS.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Unsigned is never less than zero so this error handling won't work.
Fixes: be052cc877 ('extcon: Fix hang and extcon_get/set_cable_state().')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
[cw00.choi: Change the patch title and fix signedness bug of find_cable_index_by_id() ]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Currently micd_dbtime can be set to 0 for default, 1 for 4 measurements,
or a greater than 16-bit value for 2 measurements. This patch simplifies
the symantics to 2 for 2 measurements, 4 for 4 measurements and any
other value for the default.
I am not super keen on changing the symantics of the pdata at this stage
in the drivers life, but acceptance of the DT binding for this field has
been made conditional on this happening.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Detecting an open-circuit on the microphone pin, usually means the
headset has a microphone but the cable is faulty. Currently the code
will simply stop detecting and declare nothing in this situation. It is
better to declare this as headphones such that the user can still use
their headset as plain headphones even if the microphone is faulty.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The detecting flag really refers to the microphone detection stage and
as such should be cleared before arizona_identify_headphones is called.
Also the mic flag should be set before identify headphones is called as
well.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Convert to using the newer gpiod interface for the micd_pol_gpio.
Although we still carry support for the old gpio interface from pdata.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
[cw00.choi: Modify the patch titlei to include the detailed content]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch adds bindings for the basic microphone detection platform
data.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The device properties API will load data from both device tree and ACPI,
update the binding to use this API instead of the OF API.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch removes the mutually_exclusive array of extcon-palmas.c.
After used the unique id of each external connector on 2a9de9c0f0
("extcon: Use the unique id for external connector instead of string"),
extcon driver can't directly handle the bit value indicating the external
connectors.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch removes the optional print_state() function pointer which included
in 'struct extcon_dev' because the extcon must maintain the consistent name
of extcon device on sysfs instead of inconsistent state of external connectors.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
IRQ signal before driver probe is needless because driver sends
current state after platform booting done.
So, this patch clears MUIC IRQ bits before request IRQ.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Currently the extcon code notifiers the interested listeners
before it updates the extcon state with the new state.
This will cause the listeners that use extcon_cable_get_state()
to get the stale state and loose the new state.
Fix this by first changing the extcon state variable and then
notifying listeners.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Users of find_cable_index_by_name() will cause a kernel hang
as the while loop counter is never incremented and end condition
is never reached.
extcon_get_cable_state() and extcon_set_cable_state() are broken
because they use cable index instead of cable id. This causes
the first cable state (cable.0) to be always invalid in sysfs
or extcon_get_cable_state() users.
Introduce a new function find_cable_id_by_name() that fixes
both of the above issues.
Fixes: commit 73b6ecdb93 ("extcon: Redefine the unique id of supported external connectors without 'enum extcon' type")
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
[cw00.choi: Fix minor coding style]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch fixes NULL pointer error by removing the unneeded kfree() call
of edev->name because extcon-palmas no longer allocate the memory for edev->name.
Fixes: d71aadda19 ("extcon: Remove the optional name of extcon device")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Add MAX77843_MUIC prefix to some of the defines used in max77843 extcon
driver so the max77693-private.h can be included simultaneously with
max77843-private.h.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add MAX77693 prefix to some of the defines used in max77693 extcon
driver so the max77693-private.h can be included simultaneously with
max77843-private.h.
Additionally use BIT() macro in header.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch to the same definition of state container as in MAX77693 drivers.
This will allow usage of one regulator driver in both devices: MAX77693
and MAX77843.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This prepares for merging some of the drivers between max77693 and
max77843 so the child MFD driver can be attached to any parent MFD main
driver.
Move the state container to common header file. Additionally add
consistent 'i2c' prefixes to its members (of 'struct i2c_client' type).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clean up the max77693 private header file by removing:
1. Left-overs from previous way of interrupt handling (driver uses
regmap_irq_chip).
2. Unused members of struct 'max77693_dev' related to interrupts in
extcon driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch just redefine the unique id of supported external connectors without
'enum extcon' type. Because unique id would be used on devictree file(*.dts) to
indicate the specific external connectors like key number of input framework.
So, I have the plan to move this definitions to following header file which
includes the unique id of supported external connectors.
- include/dt-bindings/extcon/extcon.h
Fixes: 2a9de9c0f0 ("extcon: Use the unique id for external connector instead of string")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the optional print_name() function pointer included in
'struct extcon_dev' because the extcon must maintain the consistent name of
extcon device on sysfs instead of inconsistent name. After merged patch[1],
extcon can maintain the consistent name of extcon device without any hard-coded
device name.
[1] https://lkml.org/lkml/2015/4/27/258
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Previously, extcon consumer driver used the extcon_register_interest()
to register the notifier chain and then to receive the notifier event
when external connector's state is changed. When registering the notifier chain
for specific external connector with extcon_register_interest(), it used the
the string name of external connector directly. There are potential problem
because of unclear, non-standard and inconsequent cable name. Namely,
it is not appropriate method to identify each external connector.
So, this patch modify the prototype of extcon_register_notifier() by using
the 'enum extcon' which are the unique id for each external connector
instead of unclear string method.
- Previously, the extcon consumer driver used the extcon_register_interest()
with 'cable_name' to point out the specific external connector. Also. it used
the un-needed structure (struct extcon_specific_cable_nb).
: int extcon_register_interest(struct extcon_specific_cable_nb *obj,
const char *extcon_name, const char *cable_name,
struct notifier_block *nb)
- Newly, the updated extcon_register_notifier() would definitely support
the same feature to detech the changed state of external connector without
any specific structure (struct extcon_specific_cable_nb).
: int extcon_register_notifier(struct extcon_dev *edev, enum extcon id,
struct notifier_block *nb)
This patch support the both extcon_register_interest() and new extcon_register_
notifier(). But the extcon_{register|unregister}_interest() will be deprecated
because extcon core would support the notifier event for extcon consumer driver
with only updated extcon_register_notifier() and 'extcon_specific_cable_nb'
will be removed if there are no extcon consumer driver with legacy
extcon_{register|unregister}_interest().
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch uses the capital letter for the name of external connectors
to improve the readability instead of small letter.
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch uses the unique id to identify the type of external connector instead
of string name. The string name have the many potential issues. So, this patch
defines the 'extcon' enumeration which includes all supported external connector
on EXTCON subsystem. If new external connector is necessary, the unique id of
new connector have to be added in 'extcon' enumeration. There are current
supported external connector in 'enum extcon' as following:
enum extcon {
EXTCON_NONE = 0x0,
/* USB external connector */
EXTCON_USB = 0x1,
EXTCON_USB_HOST = 0x2,
/* Charger external connector */
EXTCON_TA = 0x10,
EXTCON_FAST_CHARGER = 0x11,
EXTCON_SLOW_CHARGER = 0x12,
EXTCON_CHARGE_DOWNSTREAM = 0x13,
/* Audio and video external connector */
EXTCON_LINE_IN = 0x20,
EXTCON_LINE_OUT = 0x21,
EXTCON_MICROPHONE = 0x22,
EXTCON_HEADPHONE = 0x23,
EXTCON_HDMI = 0x30,
EXTCON_MHL = 0x31,
EXTCON_DVI = 0x32,
EXTCON_VGA = 0x33,
EXTCON_SPDIF_IN = 0x34,
EXTCON_SPDIF_OUT = 0x35,
EXTCON_VIDEO_IN = 0x36,
EXTCON_VIDEO_OUT = 0x37,
/* Miscellaneous external connector */
EXTCON_DOCK = 0x50,
EXTCON_JIG = 0x51,
EXTCON_MECHANICAL = 0x52,
EXTCON_END,
};
For example in extcon-arizona.c:
To use unique id removes the potential issue about handling
the inconsistent name of external connector with string.
- Previously, use the string to register the type of arizona jack connector
static const char *arizona_cable[] = {
"Mechanical",
"Microphone",
"Headphone",
"Line-out",
};
- Newly, use the unique id to register the type of arizona jack connector
static const enum extcon arizona_cable[] = {
EXTCON_MECHANICAL,
EXTCON_MICROPHONE,
EXTCON_HEADPHONE,
EXTCON_LINE_OUT,
EXTCON_NONE,
};
And this patch modify the prototype of extcon_{get|set}_cable_state_() which
uses the 'enum extcon id' instead of 'cable_index'. Because although one more
extcon drivers support USB cable, each extcon driver might has the differnt
'cable_index' for USB cable. All extcon drivers can use the unique id number
for same external connector with modified extcon_{get|set}_cable_state_().
- Previously, use 'cable_index' on these functions:
extcon_get_cable_state_(struct extcon_dev*, int cable_index)
extcon_set_cable_state_(struct extcon_dev*, int cable_index, bool state)
-Newly, use 'enum extcon id' on these functions:
extcon_get_cable_state_(struct extcon_dev*, enum extcon id)
extcon_set_cable_state_(struct extcon_dev*, enum extcon id, bool state)
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[arnd: Report the build break about drivers/usb/phy/phy-tahvo.c after using the
unique id for external connector insteadf of string]
Reported-by: Arnd Bergmann <arnd@arndb.de>
[dan.carpenter: Report the build warning of extcon_{set|get}_cable_state_()]
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Without this patch there is no call to gpiod_direction_input but the
gpio is used for irq reporting and for that the line should be in input
mode.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch removes the optional name of extcon device. Instead,
extcon_dev_register() set the device name as 'extcon[number]' naming pattern.
- /sys/class/extcon/[hardcoded device name] -> /sys/class/extcon/extcon[number]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: Graeme Gregory <gg@slimlogic.co.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Jaewon Kim <jaewon02.kim@samsung.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
If GPIOLIB=n and asm-generic/gpio.h is not used:
drivers/extcon/extcon-usb-gpio.c: In function ‘usb_extcon_detect_cable’:
drivers/extcon/extcon-usb-gpio.c:63: error: implicit declaration of function ‘gpiod_get_value_cansleep’
drivers/extcon/extcon-usb-gpio.c: In function ‘usb_extcon_probe’:
drivers/extcon/extcon-usb-gpio.c:116: error: implicit declaration of function ‘devm_gpiod_get’
drivers/extcon/extcon-usb-gpio.c:116: warning: assignment makes pointer from integer without a cast
drivers/extcon/extcon-usb-gpio.c:122: error: implicit declaration of function ‘gpiod_set_debounce’
drivers/extcon/extcon-usb-gpio.c:129: error: implicit declaration of function ‘gpiod_to_irq’
Add the missing #include <linux/gpio/consumer.h> to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch removes the 'num_cables' filed from 'struct adc_jack_pdata'
because 'struct extcon_dev' contains the 'max_supported' field which
means the number of supported cable of extcon device.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch alters the MHL-TA cable name to TA cable name because MHL-TA is not
standard name. The MHL-TA is MHL cable with charger cable (TA or USB). So, this
patch use the TA cable instead of MHL-TA to inform the charger cable state.
- MHL-TA -> TA
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch change the name of various dock devices as 'DOCK' because the name of
various dock devices have not the standard naming rules. The name of dock devices
include the differenct word but it is ambiguous and never important information
on user-space aspect. This patch unifies the name of dock devices as following:
- Dock-Smart -->|--> DOCK
- Dock-Desk -->|
- Dock-Audio -->|
- Dock-Card -->|
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch change the name of various jig cables as 'JIG' because the name of
various jig cables are strange and ambiguous on user-space aspect. They include
the different information of either USB and UART state. It is never important
for user-space process. This patch unifies the name of jig cables as following:
- JIG-USB-ON -->|--> JIG
- JIG-USB-OFF -->|
- JIG-UART-ON -->|
- JIG-UART-OFF -->|
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch add support for select accessory detect mode to HPDETL or HPDETR.
Arizona provides a headphone detection circuit on the HPDETL and HPDETR pins
to measure the impedance of an external load connected to the headphone.
Depending on board design, headphone detect pins can change to HPDETR or HPDETL.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The headphone clamping is not set correctly currently, this was missed
because the wm8280 patches and the patch fixing the clamping for wm5110
went upstream at very similar times. This patch sets the headphone
clamping correctly for wm8280.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch removes the setting of device name. Instead, extcon_dev_register()
set the device name such as 'extcon[number]' naming method.
- /sys/class/extcon/Headset Jack -> /sys/class/extcon/extcon[number]
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
This patch clean up the extcon core driver by fixing the checkpatch warning
and minor coding style issue.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch adds the extcon_get_edev_name() API to get the name of extcon device
because all information inclued in the structure extcon_dev should be accessed
by extcon core API instead of directly accessing the data.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch modify the device name as extcon[X] for sysfs by using the 'extcon'
prefix word instead of separate device name. On user-space aspect, user would
find the some extcon drvier with extcon[X] pattern. So, this patch modify the
device name as following:
- /sys/class/extcon/[device name] -> /sys/class/extcon/extcon[X]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch adds the extcon support for AXP288 PMIC which
has the BC1.2 charger detection capability. Additionally
it also adds the USB mux switching support b/w SOC and PMIC
based on GPIO control.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
[cw00.choi: Modify the log message to keep the consistent log message pattern]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Renamed to hpdet_ip_version to make it clearer what it does
and that the value in it is simply a version number.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch adds the manufactor name of each extcon device
and removes un-necessary comment in Kconfig.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
IRQ handler touches info->edev, so if interrupt occurs before extcon
device initialization it can cause NULL pointer dereference. Doing extcon
initialization before IRQ handler registration fixes this problem.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Here's the big char/misc driver patchset for 4.1-rc1.
Lots of different driver subsystem updates here, nothing major, full
details are in the shortlog below.
All of this has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlU2IMEACgkQMUfUDdst+yloDQCfbyIRL23WVAn9ckQse/y8gbjB
OT4AoKTJbwndDP9Kb/lrj2tjd9QjNVrC
=xhen
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver patchset for 4.1-rc1.
Lots of different driver subsystem updates here, nothing major, full
details are in the shortlog.
All of this has been in linux-next for a while"
* tag 'char-misc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (133 commits)
mei: trace: remove unused TRACE_SYSTEM_STRING
DTS: ARM: OMAP3-N900: Add lis3lv02d support
Documentation: DT: lis302: update wakeup binding
lis3lv02d: DT: add wakeup unit 2 and wakeup threshold
lis3lv02d: DT: use s32 to support negative values
Drivers: hv: hv_balloon: correctly handle num_pages>INT_MAX case
Drivers: hv: hv_balloon: correctly handle val.freeram<num_pages case
mei: replace check for connection instead of transitioning
mei: use mei_cl_is_connected consistently
mei: fix mei_poll operation
hv_vmbus: Add gradually increased delay for retries in vmbus_post_msg()
Drivers: hv: hv_balloon: survive ballooning request with num_pages=0
Drivers: hv: hv_balloon: eliminate jumps in piecewiese linear floor function
Drivers: hv: hv_balloon: do not online pages in offline blocks
hv: remove the per-channel workqueue
hv: don't schedule new works in vmbus_onoffer()/vmbus_onoffer_rescind()
hv: run non-blocking message handlers in the dispatch tasklet
coresight: moving to new "hwtracing" directory
coresight-tmc: Adding a status interface to sysfs
coresight: remove the unnecessary configuration coresight-default-sink
...
Since extcon.c is using raw_notifiers it must protect the notifier
list itself when [un]registering notifiers to avoid the list changing while
extcon_update_state is walking the list (through raw_notifier_call_chain).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[cw00.choi: Apply this patch to extcon.c driver instead of old extcon-class.c]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Roger Quadros