devm_kasprintf() may return NULL on failure of internal allocation thus
the assignment to .label is not safe if not checked. On error
npcm7xx_gpio_of() returns negative values so -ENOMEM in the
(unlikely) failure case of devm_kasprintf() should be fine here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 3b588e43ee ("pinctrl: nuvoton: add NPCM7xx pinctrl and GPIO driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clearing the GPIO_EN bit from chv_gpio_disable_free is a bad idea and
pinctrl-cherryview.c is the only Intel pinctrl driver doing something
like this.
Clearing the GPIO_EN bit means that if the pin was an output it is now
effectively floating. The datasheet is not clear what happens to pull ups /
downs in this case, but from testing it looks like these are disabled too,
also floating input pins.
One example where this is causing issues is the soc_button_array input
driver, this parses ACPI tables to create 2 platform devices for the
gpio_keys input driver. The list of GPIOs is passed through struct
gpio_keys_platform_data which uses gpio numbers rather then gpio_desc
pointers.
The buttons handled by this drivers short the pin to ground when pressed
and the volume buttons rely on the SoC's internal pull-up to pull the
pin high when the button is not pressed.
To get the gpio number, the soc_button_array code calls gpiod_get_index
followed by a desc_to_gpio call and then gpiod_put on the gpio_desc.
This last call causes chv_gpio_disable_free to clear the GPIO_EN bit.
When the gpio_keys driver then loads next it gets the gpio_desc again
causing the GPIO_EN bit to be set again and immediately reads the GPIO
value which for the volume buttons reads 0 at this time, causing a spurious
press of the volume buttons to get reported.
Putting a small delay between the gpio_desc request and the read fixes
this, I assume that this is caused by the pull-up being temporarily
disabled while the GPIO_EN bit is cleared as the powerbutton which also
has its GPIO_EN bit cleared does not have this problem.
The soc_button_array code is not the only code temporarily requesting GPIOs
the DWC3 PCI code also does this, to set the enable and reset GPIOs for the
external phy, so that the code instantiating the ULPI phy can read the
vendor and product ID registers from the phy. These GPIOs are released
after this so that the PHY driver can claim and use them when it loads.
Another example of temporary GPIO usage would be a user-space set_gpio
utility using the userspace ioctls to set a GPIO as output value 0 or 1,
having the GPIO revert to floating as soon as this utility exits would
certainly be unexpected behavior.
One argument in favor of clearing the GPIO_EN bit is if the GPIO is going
to be muxed to another function after being released, but in that case
chv_pinmux_set_mux() already clears it.
TL;DR: Clearing the GPIO_EN bit from is a bad idea, this commit therefor
removes the clearing from chv_gpio_disable_free(), replacing it with code
to clear the interrupt-trigger condition so that the GPIO stops generating
interrupts when released, as pinctrl-baytrail.c does.
Note this commit adds a !chv_pad_locked() condition to the trigger clearing
call, which the original GPIO_EN clearing code was missing.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This is a preparation patch for clearing the interrupt trigger from
chv_gpio_disable_free().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
If we assign the result of of_get_child_count() to an unsigned int,
the code will not detect any errors. Therefore assign it to an int
instead.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This fixes the check for unused mdio bus setting and the following static
checker warning:
drivers/pinctrl/pinctrl-rzn1.c:198 rzn1_pinctrl_mdio_select()
warn: always true condition '(ipctl->mdio_func[mdio] >= 0) => (0-u32max >= 0)'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
- Fix VIN (Video IN) versioned groups on R-Car V2H, H3, and M3-W,
- Add I2C[0-3], DU1, VIN, QSPI1, and SDHI pin groups on RZ/G1C,
- Add audio, SDHI, VIN, HSCIF, and CAN(FD) support on R-Car E3,
- Add QSPI pin groups on R-Car V3M and V3H,
- Add VIN and CAN(FD) pin groups on R-Car M3-N,
- Add I2C[035] pin groups on R-Car H3 and M3-W,
- Add pinctrl and GPIO support for the new RZ/A2M (R7S9210) SoC,
- Small cleanups,
- Maintainership updates.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCW/fATQAKCRCKwlD9ZEnx
cEcRAPoCtfqfL82fb4Yj6zTrwD8dpy2TVpRYT95YRNuPegcWZwEAxpv4bUNVAMQJ
Wj6GYkhMTuGBaaUJzNGJclD7u7nJcgc=
=YGuc
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.21-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.21
- Fix VIN (Video IN) versioned groups on R-Car V2H, H3, and M3-W,
- Add I2C[0-3], DU1, VIN, QSPI1, and SDHI pin groups on RZ/G1C,
- Add audio, SDHI, VIN, HSCIF, and CAN(FD) support on R-Car E3,
- Add QSPI pin groups on R-Car V3M and V3H,
- Add VIN and CAN(FD) pin groups on R-Car M3-N,
- Add I2C[035] pin groups on R-Car H3 and M3-W,
- Add pinctrl and GPIO support for the new RZ/A2M (R7S9210) SoC,
- Small cleanups,
- Maintainership updates.
The suniv F1C100s chip (several new F-series SoCs) of Allwinner has a
pin
controller like other SoCs from Allwinner.
Add support for it.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds support for the pin and gpio controller found in R7S9210 (RZ/A2) SoCs.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the QSPI{0|1} pins/groups/functions to the R8A77980 PFC driver.
[Sergei: ported to the upstream driver, fixed up the swapped QSPI0 SPCLK/
SSL pins, fixed up the comments, moved the QSPI pins/groups/functions to
be in the alphanumeric order, removed unneeded empty lines, renamed the
patch.]
Signed-off-by: Dmitry Shifrin <dmitry.shifrin@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
We just changed the code so we apply bias disable on the correct
register but forgot to align the register calculation. The result
is that we apply the change on the correct register, but possibly
at the incorrect offset/bit
This went undetected because offsets tends to be the same between
REG_PULL and REG_PULLEN for a given pin the EE controller. This
is not true for the AO controller.
Fixes: e39f9dd820 ("pinctrl: meson: fix pinconf bias disable")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This was missed when tiles support was added in a revison and
causes the driver to fail to load.
Fixes: 9cf0c526bc ("pinctrl: qcom: Add sdm660 pinctrl driver")
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-mediatek@lists.infradead.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add PM suspend callbacks to the msm core driver that select the
sleep and default pinctrl states. Then wire those callbacks up
in the sdm845 driver, for those boards that may have GPIO hogs
that need to change state during suspend.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds MT7629 pinctrl driver based on MediaTek pinctrl-moore core.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After patch b96eea718b ("pinctrl: fsl: add scu based pinctrl support"),
NO_PAD_CTL pads map are not skipped anymore which results in
a possible memory corruption. As we actually only need to create config
maps for SCU pads and MMIO pads which are not using the default config
(a.k.a IMX_NO_PAD_CTL), so let's add a proper check before creating
the config maps. And during MMIO pads parsing, we also need update the
list_p point as SCU case to ensure the pin data next parsed is correct.
Cc: Linus Walleij <linus.walleij@linaro.org>
Fixes: b96eea718b ("pinctrl: fsl: add scu based pinctrl support")
Reported-by: Martin Kaiser <martin@kaiser.cx>
Suggested-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Martin Kaiser <martin@kaiser.cx>
Tested-by: Leonard Crestez <leonard.crestez@nxp.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl and gpio driver for Actions Semi S700 SoC. The driver
supports pinctrl, pinmux, pinconf, gpio and interrupt functionalities
through a range of registers common to both gpio driver and pinctrl driver.
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pad control for s900 and s700 are differs in number of
pull control configuraions
s900 has 4 pull controls - high impedence, pull up, pull down, repeater
s700, s500 has 2 pull controls - pull up and pull down
so pad control configuration has to SoC specific, moved out from pinctrl
common to s900 specific.
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move generic defines common to the Owl family out of S900 driver.
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a hwspinlock if defined in device tree use it to protect
configuration registers.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds CAN FD{0,1} pins, groups and functions to the R8A77990
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
[geert: Move canfd from common to automotive]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN{0,1} pins, groups and functions to the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN FD{0,1} pins, groups and functions to the R8A77965
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN{0,1} pins, groups and functions to the R8A77965 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds I2C{0,3,5} pins, groups and functions to the R8A7796 SoC.
These pins are physically muxed with other pins. Therefore, setup of
MOD_SEL is needed for exclusive control with other pins.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds I2C{0,3,5} pins, groups and functions to
the R8A7795 ES1.x SoC.
These pins are physically muxed with other pins. Therefore, setup of
MOD_SEL is needed for exclusive control with other pins.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds I2C{0,3,5} pins, groups and functions to the R8A7795 SoC.
These pins are physically muxed with other pins. Therefore, setup of
MOD_SEL is needed for exclusive control with other pins.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Used by I2C controllers 0, 3 and 5 in R8A7795 and R8A7796 SoCs.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The PINMUX_IPSR_MSEL2() and PINMUX_IPSR_PHYS() macros are unused, and
will conflict with generic macros that are to be added.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds HSCIF{0,1,2,3,4} pins, groups and functions to
the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The rk3188 has pins that are not handled through the regular iomuxing
for handling either nand-flash or an emmc and are set through only one
specifal setting. So utilize the routing function to simply do that
setting depending on one of the core nand/emmc signals that are actually
regular pins handled through pinctrl.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Right now we expect the pin-rounting settings to be in the same area
as the iomux setting itself. And while that seems to be true for all
newer Rockchip socs, back in the wild west days of old this wasn't true.
Nowadays pin settings in the GRF normally stay in the GRF and the same
is true for pins configured from PMU registers. But old socs like the
rk3188 really sprinkle pin settings somewhat randomly through both
for its bank0.
Therefore add the option to specify a location for the route setting,
so that we can map older socs correctly. We'll keep "same" as the
default, so that we only need to specify a location in the corner-cases
described above.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When attempting to setup up a gpio hog, device probing will repeatedly
fail with -EPROBE_DEFERED errors. It is caused by a circular dependency
between the gpio and pinctrl frameworks. If the gpio-ranges property is
present in device tree, then the gpio framework will handle the gpio pin
registration and eliminate the circular dependency.
See Christian Lamparter's commit a86caa9ba5 ("pinctrl: msm: fix
gpio-hog related boot issues") for a detailed commit message that
explains the issue in much more detail. The code comment in this commit
came from Christian's commit.
I did not test this change against any hardware supported by this
particular driver, however I was able to validate this same fix works
for pinctrl-spmi-gpio.c using a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Modify GPIO direction setting in pin configuration function by using
generic GPIO functions to set the GPIO direction instead of direct
access to the GPIO direction register.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Tested-by: Kun Yi <kunyi@google.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIOX tsin_a pins wrongly uses the SDCard pinctrl bits, this
patch completely removes these pins entries until we find out what
are the correct bits and registers to be used instead.
Fixes: 5a6ae9b801 ("pinctrl: meson-gxl: add tsin_a pins")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pin, mux and functions definitions for VIN4 and VIN5 for R-Car E3.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The VIN4 and VIN5 interfaces support parallel video input.
Add pin, mux and functions definitions for VIN4 and VIN5 for R-Car M3-N.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Versioned VIN groups can appear on different sets of pins. Using the
VIN_DATA_PIN_GROUP macro now supports proper naming of said groups
through an optional 'version' argument.
Use the 'version' argument for said macro to fix naming of versioned
groups for the R-Car M3-W R8A7796 SoC.
Fixes: a5c2949ff7 ("pinctrl: sh-pfc: r8a7796: Deduplicate VIN4 pin definitions")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Versioned VIN groups can appear on different sets of pins. Using the
VIN_DATA_PIN_GROUP macro now supports proper naming of said groups
through an optional 'version' argument.
Use the 'version' argument for said macro to fix naming of versioned
groups for the R-Car H3 R8A7795 SoC.
Fixes: 9942a5b529 ("pinctrl: sh-pfc: r8a7795: Deduplicate VIN4 pin definitions")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Versioned VIN groups can appear on different sets of pins. Using the
VIN_DATA_PIN_GROUP macro now supports proper naming of said groups
through an optional 'version' argument.
Use the 'version' argument for said macro to fix naming of versioned
groups for the R-Car V2H R8A7792 SoC.
Fixes: 7dd74bb1f0 ("pinctrl: sh-pfc: r8a7792: Add VIN pin groups")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
VIN data groups may appear on different sets of pins, usually named
"vinX_data_[a|b]". The existing VIN_DATA_PIN_GROUP() does not support
appending the '_a' or '_b' suffix, leading to the definition of group
names not consistent with the ones defined using the SH_PFC_PIN_GROUP()
macro.
Fix this by making the VIN_DATA_PIN_GROUP macro a variadic one,
which accepts an optional 'version' argument.
Fixes: 423caa5253 ("pinctrl: sh-pfc: r8a779[01]: Move 'union vin_data' to shared header file")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the QSPI{0|1} pins/groups/functions to the R8A77970 PFC driver.
[Sergei: ported to the upstream driver, fixed up the swapped QSPI0 SPCLK/
SSL pins, fixed up the comments, moved the QSPI pins/groups/functions to
be in the alphanumeric order, removed unneeded empty lines, renamed the
patch.]
Signed-off-by: Dmitry Shifrin <dmitry.shifrin@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch supports the {get,set}_io_voltage operations of SDHI.
This operates the IOCTRL30 register on the R8A77990 SoC and makes
1.8V/3.3V signal voltage switch possible.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds SDHI{0,1,3} pins, groups and functions to the R8A77990
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
We already had an earlier conclusion that all new i.MX Socs will keep
using the legacy i.MX Pinctrl bindings instead of generic pin config.
However, MX7ULP generic pin config binding support has already been in
tree before that time. Per SoC maintainers' suggestions, in order to
get a better consistency for all i.MX devices, we'd like to go back to
imx legacy binding for MX7ULP as well.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clang warns when one enumerated type is implicitly converted to another:
drivers/pinctrl/pinctrl-zynq.c:985:18: warning: implicit conversion from
enumeration type 'enum zynq_pin_config_param' to different enumeration
type 'enum pin_config_param' [-Wenum-conversion]
{"io-standard", PIN_CONFIG_IOSTANDARD, zynq_iostd_lvcmos18},
~ ^~~~~~~~~~~~~~~~~~~~~
drivers/pinctrl/pinctrl-zynq.c:990:16: warning: implicit conversion from
enumeration type 'enum zynq_pin_config_param' to different enumeration
type 'enum pin_config_param' [-Wenum-conversion]
= { PCONFDUMP(PIN_CONFIG_IOSTANDARD, "IO-standard", NULL, true),
~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/pinctrl/pinconf-generic.h:163:11: note: expanded from
macro 'PCONFDUMP'
.param = a, .display = b, .format = c, .has_arg = d \
^
2 warnings generated.
It is expected that pinctrl drivers can extend pin_config_param because
of the gap between PIN_CONFIG_END and PIN_CONFIG_MAX so this conversion
isn't an issue. Most drivers that take advantage of this define the
PIN_CONFIG variables as constants, rather than enumerated values. Do the
same thing here so that Clang no longer warns.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clang warns when one enumerated type is implicitly converted to another:
drivers/pinctrl/pinctrl-lpc18xx.c:643:29: warning: implicit conversion
from enumeration type 'enum lpc18xx_pin_config_param' to different
enumeration type 'enum pin_config_param' [-Wenum-conversion]
{"nxp,gpio-pin-interrupt", PIN_CONFIG_GPIO_PIN_INT, 0},
~ ^~~~~~~~~~~~~~~~~~~~~~~
drivers/pinctrl/pinctrl-lpc18xx.c:648:12: warning: implicit conversion
from enumeration type 'enum lpc18xx_pin_config_param' to different
enumeration type 'enum pin_config_param' [-Wenum-conversion]
PCONFDUMP(PIN_CONFIG_GPIO_PIN_INT, "gpio pin int", NULL, true),
~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/pinctrl/pinconf-generic.h:163:11: note: expanded from
macro 'PCONFDUMP'
.param = a, .display = b, .format = c, .has_arg = d \
^
2 warnings generated.
It is expected that pinctrl drivers can extend pin_config_param because
of the gap between PIN_CONFIG_END and PIN_CONFIG_MAX so this conversion
isn't an issue. Most drivers that take advantage of this define the
PIN_CONFIG variables as constants, rather than enumerated values. Do the
same thing here so that Clang no longer warns.
Link: https://github.com/ClangBuiltLinux/linux/issues/140
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clang warns when one enumerated type is implicitly converted to another:
drivers/pinctrl/bcm/pinctrl-bcm2835.c:707:40: warning: implicit
conversion from enumeration type 'enum bcm2835_pinconf_param' to
different enumeration type 'enum pin_config_param' [-Wenum-conversion]
configs[0] = pinconf_to_config_packed(BCM2835_PINCONF_PARAM_PULL, pull);
~~~~~~~~~~~~~~~~~~~~~~~~ ^~~~~~~~~~~~~~~~~~~~~~~~~~
1 warning generated.
It is expected that pinctrl drivers can extend pin_config_param because
of the gap between PIN_CONFIG_END and PIN_CONFIG_MAX so this conversion
isn't an issue. Most drivers that take advantage of this define the
PIN_CONFIG variables as constants, rather than enumerated values. Do the
same thing here so that Clang no longer warns.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clang warns when one enumerated type is implicitly converted to another:
drivers/pinctrl/sprd/pinctrl-sprd.c:845:19: warning: implicit conversion
from enumeration type 'enum sprd_pinconf_params' to different
enumeration type 'enum pin_config_param' [-Wenum-conversion]
{"sprd,control", SPRD_PIN_CONFIG_CONTROL, 0},
~ ^~~~~~~~~~~~~~~~~~~~~~~
drivers/pinctrl/sprd/pinctrl-sprd.c:846:22: warning: implicit conversion
from enumeration type 'enum sprd_pinconf_params' to different
enumeration type 'enum pin_config_param' [-Wenum-conversion]
{"sprd,sleep-mode", SPRD_PIN_CONFIG_SLEEP_MODE, 0},
~ ^~~~~~~~~~~~~~~~~~~~~~~~~~
It is expected that pinctrl drivers can extend pin_config_param because
of the gap between PIN_CONFIG_END and PIN_CONFIG_MAX so this conversion
isn't an issue. Most drivers that take advantage of this define the
PIN_CONFIG variables as constants, rather than enumerated values. Do the
same thing here so that Clang no longer warns.
Link: https://github.com/ClangBuiltLinux/linux/issues/138
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clang warns when one enumerated type is implicitly converted to another:
drivers/pinctrl/pinctrl-max77620.c:56:12: warning: implicit conversion
from enumeration type 'enum max77620_pinconf_param' to different
enumeration type 'enum pin_config_param' [-Wenum-conversion]
.param = MAX77620_ACTIVE_FPS_SOURCE,
^~~~~~~~~~~~~~~~~~~~~~~~~~
It is expected that pinctrl drivers can extend pin_config_param because
of the gap between PIN_CONFIG_END and PIN_CONFIG_MAX so this conversion
isn't an issue. Most drivers that take advantage of this define the
PIN_CONFIG variables as constants, rather than enumerated values. Do the
same thing here so that Clang no longer warns.
Link: https://github.com/ClangBuiltLinux/linux/issues/139
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When attempting to setup up a gpio hog, device probing would repeatedly
fail with -EPROBE_DEFERED errors. It was caused by a circular dependency
between the gpio and pinctrl frameworks. If the gpio-ranges property is
present in device tree, then the gpio framework will handle the gpio pin
registration and eliminate the circular dependency.
See Christian Lamparter's commit a86caa9ba5 ("pinctrl: msm: fix
gpio-hog related boot issues") for a detailed commit message that
explains the issue in much more detail. The code comment in this commit
came from Christian's commit.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Trivial fix to clean up indentation issues, add one level of
indentation on two if statements.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove comma from terminator line to allow compiler fail
in case an entry has been put in a wrong place by any weird reason.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Remove comma from terminator line to allow compiler fail
in case an entry has been put in a wrong place by any weird reason.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Remove comma from terminator line to allow compiler fail
in case an entry has been put in a wrong place by any weird reason.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Remove comma from terminator line to allow compiler fail
in case an entry has been put in a wrong place by any weird reason.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Remove comma from terminator line to allow compiler fail
in case an entry has been put in a wrong place by any weird reason.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is no need to include acpi.h since driver doesn't use anything from it
except the propagation of mod_devicetable.h.
Include latter directly instead.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is no need to include acpi.h since driver doesn't use anything from it
except the propagation of mod_devicetable.h.
Include latter directly instead.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is no need to include acpi.h since driver doesn't use anything from it
except the propagation of mod_devicetable.h.
Include latter directly instead.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The reason of including <linux/bitops.h> here is just for BIT() and Co macros.
Since commit 8bd9cb51da
("... Move some macros from <linux/bitops.h> to a new <linux/bits.h> file"),
<linux/bits.h> is enough for such compile-time macros.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since there are no more users, unexport it and make static.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The local ->probe() stub does nothing except calling
a generic Intel pin control probe function. Thus,
it's not needed and generic function may be called directly.
Convert the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The local ->probe() stub does nothing except calling
a generic Intel pin control probe function. Thus,
it's not needed and generic function may be called directly.
Convert the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The local ->probe() stub does nothing except calling
a generic Intel pin control probe function. Thus,
it's not needed and generic function may be called directly.
Convert the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The local ->probe() stub does nothing except calling
a generic Intel pin control probe function. Thus,
it's not needed and generic function may be called directly.
Convert the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The local ->probe() stub does nothing except calling
a generic Intel pin control probe function. Thus,
it's not needed and generic function may be called directly.
Convert the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The local ->probe() stub does nothing except calling
a generic Intel pin control probe function. Thus,
it's not needed and generic function may be called directly.
Convert the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The local ->probe() stub does nothing except calling
a generic Intel pin control probe function. Thus,
it's not needed and generic function may be called directly.
Convert the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add SH_PFC_PIN_CFG_IO_VOLTAGE definition for the SDHI pins
capable of switching voltage, also add pin groups and functions
for SDHI0 and SDHI1. Please note that with the RZ/G1C only 1
bit of the POC Control Register is used to control each interface.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Some VIN channels support less than 24 lanes. As union vin_data always
consumes space for 24 lanes, this wastes memory.
Hence introduce new smaller unions vin_data12 and vin_data16, to
accommodate VIN channels with only 12 or 16 lanes.
This reduces the static pin controller driver size by 320 bytes for
R-Car V2H, and by 96 bytes for R-Car E2.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
This patch adds Audio SSI{0,1,2,3,4,5,6,7,8,9} pins, groups
and functions to the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[simon: rebase]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds AUDIO_CLK{A,B,C}, AUDIO_CLKOUT, AUDIO_CLKOUT{1,2,3}
pins, groups and functions to the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[simon: rebase]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add QSPI1 pin groups and function to the RZ/G1C (a.k.a. R8A77470)
pinctrl driver.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add VIN[01] pin groups and functions to the RZ/G1C (a.k.a.
R8A77470) pinctrl driver.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add DU1 pin groups and function to the RZ/G1C (a.k.a. R8A77470)
pinctrl driver.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds I2C[0123] groups and functions to the RZ/G1C
(a.k.a. R8A77470) pinctrl driver.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The BCM2835 pinctrl driver acquires a spinlock in its ->irq_enable,
->irq_disable and ->irq_set_type callbacks. Spinlocks become sleeping
locks with CONFIG_PREEMPT_RT_FULL=y, therefore invocation of one of the
callbacks in atomic context may cause a hard lockup if at least two GPIO
pins in the same bank are used as interrupts. The issue doesn't occur
with just a single interrupt pin per bank because the lock is never
contended. I'm experiencing such lockups with GPIO 8 and 28 used as
level-triggered interrupts, i.e. with ->irq_disable being invoked on
reception of every IRQ.
The critical section protected by the spinlock is very small (one bitop
and one RMW of an MMIO register), hence converting to a raw spinlock
seems a better trade-off than converting the driver to threaded IRQ
handling (which would increase latency to handle an interrupt).
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MX8QXP contains a system controller that is responsible for controlling
the pad setting of the IPs that are present. Communication between the
host processor running an OS and the system controller happens through
a SCU protocol. This patch adds the SCU based MX8QXP pinctrl driver.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some i.MX SoCs (e.g. MX8QXP and MX8QM) contain a system controller
that is responsible for controlling the pad setting of the IPs that
are present. Communication between the host processor running an OS
and the system controller happens through a SCU protocol.
This patch classifies the pad settings into two categories: MMIO and SCU.
For the original MMIO method, no functional changes except organize them
into a few imx_*_mmio() functions. Besides that, we add the SCU based
Pad Mux and Pinconf setting support which are implemented in pinctrl-scu.c.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AO pull register definition is inverted between pull (up/down) and
pull enable. Fixing this allows to properly apply bias setting
through pinconf
Fixes: 0fefcb6876 ("pinctrl: Add support for Meson8b")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AO pull register definition is inverted between pull (up/down) and
pull enable. Fixing this allows to properly apply bias setting
through pinconf
Fixes: 6ac7309511 ("pinctrl: add driver for Amlogic Meson SoCs")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AO pull register definition is inverted between pull (up/down) and
pull enable. Fixing this allows to properly apply bias setting
through pinconf
Fixes: 468c234f9e ("pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a bias is enabled on a pin of an Amlogic SoC, calling .pin_config_set()
with PIN_CONFIG_BIAS_DISABLE will not disable the bias. Instead it will
force a pull-down bias on the pin.
Instead of the pull type register bank, the driver should access the pull
enable register bank.
Fixes: 6ac7309511 ("pinctrl: add driver for Amlogic Meson SoCs")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO
lines as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can
use only the fastpatch callbacks to enable/disable irqs
like any normal irqchip, especially the gpiod_lock_as_irq()
has been improved to be callable in fastpath context.
A bunch of rework had to be done to achieve this but it is
a big win since I never liked to restrict this to slowpath.
The only call requireing slowpath was try_module_get() and
this is kept at the .request_resources() slowpath callback.
In the GPIO CEC driver this is a big win sine a single
line is used for both outgoing and incoming traffic, and
this needs to use IRQs for incoming traffic while actively
driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a
"cookie" (struct gpio_array) and a bitmap for setting or
getting multiple GPIO lines at once. This improvement
orginated in a specific need to speed up an OMAP1 driver and
has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot
of checks and code when we want things to go really fast.
The previous code would minimize the number of calls
down to the driver callbacks assuming the CPU speed was
orders of magnitude faster than the I/O latency, but this
assumption was wrong on several platforms: what we needed
to do was to profile and improve the speed on the hot
path of the array functions and this change is now
completed.
- Clean out the painful and hard to grasp BNF experiments
from the device tree bindings. Future approaches are looking
into using JSON schema for this purpose. (Rob Herring
is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and
other contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin
control driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver.
-----BEGIN PGP SIGNATURE-----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=YosT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.20 series:
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO lines
as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can use only
the fastpatch callbacks to enable/disable irqs like any normal
irqchip, especially the gpiod_lock_as_irq() has been improved to be
callable in fastpath context.
A bunch of rework had to be done to achieve this but it is a big
win since I never liked to restrict this to slowpath. The only call
requireing slowpath was try_module_get() and this is kept at the
.request_resources() slowpath callback. In the GPIO CEC driver this
is a big win sine a single line is used for both outgoing and
incoming traffic, and this needs to use IRQs for incoming traffic
while actively driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a "cookie"
(struct gpio_array) and a bitmap for setting or getting multiple
GPIO lines at once.
This improvement orginated in a specific need to speed up an OMAP1
driver and has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot of checks
and code when we want things to go really fast.
The previous code would minimize the number of calls down to the
driver callbacks assuming the CPU speed was orders of magnitude
faster than the I/O latency, but this assumption was wrong on
several platforms: what we needed to do was to profile and improve
the speed on the hot path of the array functions and this change is
now completed.
- Clean out the painful and hard to grasp BNF experiments from the
device tree bindings. Future approaches are looking into using JSON
schema for this purpose. (Rob Herring is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and other
contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin control
driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver"
* tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (116 commits)
gpio: Clarify kerneldoc on gpiochip_set_chained_irqchip()
gpio: Remove unused 'irqchip' argument to gpiochip_set_cascaded_irqchip()
gpio: Drop parent irq assignment during cascade setup
mmc: pwrseq_simple: Fix incorrect handling of GPIO bitmap
gpio: fix SNPS_CREG kconfig dependency warning
gpiolib: Initialize gdev field before is used
gpio: fix kernel-doc after devres.c file rename
gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
gpio: syscon: Fix possible NULL ptr usage
gpiolib: Show correct direction from the beginning
pinctrl: msm: Use init_valid_mask exported function
gpiolib: Add init_valid_mask exported function
GPIO: add single-register GPIO via CREG driver
dt-bindings: Document the Synopsys GPIO via CREG bindings
gpio: mockup: use device properties instead of platform_data
gpio: Slightly more helpful debugfs
gpio: omap: Remove set but not used variable 'dev'
gpio: omap: drop omap_gpio_list
Accept partial 'gpio-line-names' property.
gpio: omap: get rid of the conditional PM runtime calls
...
There were no significant changes to the core this time!
New drivers:
- Broadcom Northstar pin control driver.
- Mediatek MT8183 subdriver.
- Mediatek MT7623 subdriver.
- Mediatek MT6765 subdriver.
- Meson g12a subdriver.
- Nuvoton NPCM7xx pin control and GPIO driver.
- Qualcomm QCS404 pin control and GPIO subdriver.
- Qualcomm SDM660 pin control and GPIO subdriver.
- Renesas R8A7744 PFC subdriver.
- Renesas R8A774C0 PFC subdriver.
- Renesas RZ/N1 pinctrl driver
Major improvements:
- Pulled the GPIO support for Ingenic over from the GPIO
subsystem and consolidated it all in the Ingenic pin control
driver.
- Major cleanups and consolidation work in all Intel drivers.
- Major cleanups and consolidation work in all Mediatek drivers.
- Lots of incremental improvements to the Renesas PFC pin
controller family.
- All drivers doing GPIO now include <linux/gpio/driver.h> and
nothing else.
-----BEGIN PGP SIGNATURE-----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=rBtH
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.20 series:
There were no significant changes to the core this time! Bur the new
Qualcomm, Mediatek and Broadcom drivers are quite interesting as they
will be used in a few million embedded devices the coming years as it
seems.
New drivers:
- Broadcom Northstar pin control driver.
- Mediatek MT8183 subdriver.
- Mediatek MT7623 subdriver.
- Mediatek MT6765 subdriver.
- Meson g12a subdriver.
- Nuvoton NPCM7xx pin control and GPIO driver.
- Qualcomm QCS404 pin control and GPIO subdriver.
- Qualcomm SDM660 pin control and GPIO subdriver.
- Renesas R8A7744 PFC subdriver.
- Renesas R8A774C0 PFC subdriver.
- Renesas RZ/N1 pinctrl driver
Major improvements:
- Pulled the GPIO support for Ingenic over from the GPIO subsystem
and consolidated it all in the Ingenic pin control driver.
- Major cleanups and consolidation work in all Intel drivers.
- Major cleanups and consolidation work in all Mediatek drivers.
- Lots of incremental improvements to the Renesas PFC pin controller
family.
- All drivers doing GPIO now include <linux/gpio/driver.h> and
nothing else"
* tag 'pinctrl-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (153 commits)
pinctrl: sunxi: Fix a memory leak in 'sunxi_pinctrl_build_state()'
gpio: uniphier: include <linux/bits.h> instead of <linux/bitops.h>
pinctrl: uniphier: include <linux/bits.h> instead of <linux/bitops.h>
dt-bindings: pinctrl: bcm4708-pinmux: improve example binding
pinctrl: geminilake: Sort register offsets by value
pinctrl: geminilake: Get rid of unneeded ->probe() stub
pinctrl: geminilake: Update pin list for B0 stepping
pinctrl: renesas: Fix platform_no_drv_owner.cocci warnings
pinctrl: mediatek: Make eint_m u16
pinctrl: bcm: ns: Use uintptr_t for casting data
pinctrl: madera: Fix uninitialized variable bug in madera_mux_set_mux
pinctrl: gemini: Fix up TVC clock group
pinctrl: gemini: Drop noisy debug prints
pinctrl: gemini: Mask and set properly
pinctrl: mediatek: select GPIOLIB
pinctrl: rza1: don't manually release devm managed resources
MAINTAINERS: update entry for Mediatek pin controller
pinctrl: bcm: add Northstar driver
dt-bindings: pinctrl: document Broadcom Northstar pin mux controller
pinctrl: qcom: fix 'const' pointer handling
...
If 'krealloc()' fails, 'pctl->functions' is set to NULL.
We should instead use a temp variable in order to be able to free the
previously allocated memeory, in case of OOM.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The reason of including <linux/bitops.h> here is just for BIT() macro.
Since commit 8bd9cb51da ("locking/atomics, asm-generic: Move some
macros from <linux/bitops.h> to a new <linux/bits.h> file"),
<linux/bits.h> is enough for such compile-time macros.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The local ->probe() stub does nothing except calling
a generic Intel pin control probe function. Thus,
it's not needed and generic function may be called directly.
This patch converts the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to an updated pin list few names of the pins can be spelled better,
taking into account their primary functions.
Thus, update a pin list to cover B0 stepping.
Note, SPI numbering had been fixed even in A0 public documentation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Nicholas Mc Guire