The watchdog timer on the SoCFPGA platform is the Synopsys Designware watchdog.
Enable CONFIG_DW_WATCHDOG for the driver to get built.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The DTSI file for the Nomadik does not properly specify how the
PL180 levelshifter is connected: the Nomadik actually needs all
the five st,sig-dir-* flags set to properly control all lines out.
Further this board supports full power cycling of the card, and
since this variant has no hardware clock gating, it needs a
ridiculously low frequency setting to keep up with the ever
overflowing FIFO.
The pin configuration set-up is a bit of a mystery, because of
course these pins are a mix of inputs and outputs. However the
reference implementation sets all pins to "output" with
unspecified initial value, so let's do that here as well.
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
assembly fixes, the other things are mostly board related:
- A series of omap assembly code fixes to fix issues with rodata with
ARM_KERNMEM_PERMS enabled. We had several places writing to rodata,
which is bad. The fix in most cases is to load the value from data
section using a pointer. Let's also enable ARM_KERNMEM_PERMS so
DEBUG_RODATA gets selected by default. And while testing things,
I also added few more loadable driver modules to the defconfig that
I seem to need quite often.
- Fix a long standing omap5 RTC mystery and enable RTC where we need
to ensure the SoC msecure pin is high so we can write to the RTC
registers.
- Fix irq types for am437x
- A series of minor dts fixes for sbc-am57x and cl-som-am57x
- Fixes for torpedo dts to make WLAN behave and to remove a duplicate
i2c rate entry
This series also includes few minor changes that are not stricly
fixes, but would be good to get in during the early -rc cycle:
- Remove legacy mailbox platform data that is no longer needed
- Add the pdata-quirks needed for the new pwm-omap-dmtimer so
people can use it
- Enable ti,mbox-send-noirq that's needed by wkup_m3 driver
- Enable SPLIT and DWARF4 in omap2plus_defconfig as it makes the
initramfs quite a bit smaller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NqvQ
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps with the most intrusive stuff being read-only data
assembly fixes, the other things are mostly board related:
- A series of omap assembly code fixes to fix issues with rodata with
ARM_KERNMEM_PERMS enabled. We had several places writing to rodata,
which is bad. The fix in most cases is to load the value from data
section using a pointer. Let's also enable ARM_KERNMEM_PERMS so
DEBUG_RODATA gets selected by default. And while testing things,
I also added few more loadable driver modules to the defconfig that
I seem to need quite often.
- Fix a long standing omap5 RTC mystery and enable RTC where we need
to ensure the SoC msecure pin is high so we can write to the RTC
registers.
- Fix irq types for am437x
- A series of minor dts fixes for sbc-am57x and cl-som-am57x
- Fixes for torpedo dts to make WLAN behave and to remove a duplicate
i2c rate entry
This series also includes few minor changes that are not stricly
fixes, but would be good to get in during the early -rc cycle:
- Remove legacy mailbox platform data that is no longer needed
- Add the pdata-quirks needed for the new pwm-omap-dmtimer so
people can use it
- Enable ti,mbox-send-noirq that's needed by wkup_m3 driver
- Enable SPLIT and DWARF4 in omap2plus_defconfig as it makes the
initramfs quite a bit smaller
* tag 'omap-for-v4.5/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (23 commits)
ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings
ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux
ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux
ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency
ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2
ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address
ARM: dts: LogicPD Torpedo: Revert Duplicative Entries
ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types
ARM: dts: am4372: fix irq type for arm twd and global timer
ARM: dts: Fix wl12xx missing clocks that cause hangs
ARM: OMAP: Add PWM dmtimer platform data quirks
ARM: omap2plus_defconfig: Enable ARM_KERNMEM_PERMS and few loadable modules
ARM: OMAP2+: Fix ppa_zero_params and ppa_por_params for rodata
ARM: OMAP2+: Fix l2_inv_api_params for rodata
ARM: OMAP2+: Fix save_secure_ram_context for rodata
ARM: OMAP2+: Fix l2dis_3630 for rodata
ARM: OMAP2+: Fix wait_dll_lock_timed for rodata
ARM: OMAP2+: Remove legacy mailbox device instantiation
ARM: dts: AM4372: Add ti,mbox-send-noirq to wkup_m3 mailbox
ARM: dts: AM33xx: Add ti,mbox-send-noirq to wkup_m3 mailbox
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- sama5d4: error in DBGU index
- addition of phy properties in several boards
- at91sam9n12ek fix a panel compatible string
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWqdjFAAoJEAf03oE53VmQG30H/R9luD6d9ebmhaOE7ay40HAy
RrG8wtRQ/zgxf37SntoJxyVxxXWsDsb7sOR1LRXiT7FEGWr3Eip7B1uwmasC8pky
ich2Yj5pGVUH+qscm26GDGyHbNwIrFOQyl1t/R6upVpITlXa0bpaEIXx3RejH8PN
Wk4pMZg/4OkUXlcmYNU0Rz8ban8GfJ428bkLxMKeUXUAjvevNlWqTvOqC+QIrzUC
w3iDoXfhc81sqrOzBzW44H28g7rh//d3TAfzMbM1BJti880QkP+CksG5qHvogI5f
olN4+9QmV9tLXOr2K6iUkM8dwzHYW/3PPBR1CHODjSLP0rQ2Assy+DPxyO64Rtk=
=jJrB
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
First fixes for 4.5. Only DT changes:
- sama5d4: error in DBGU index
- addition of phy properties in several boards
- at91sam9n12ek fix a panel compatible string
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: dts: at91: sama5d4 xplained: fix phy0 IRQ type
ARM: dts: at91: sama5d4 xplained: properly mux phy interrupt
ARM: dts: at91: sama5d4ek: add phy address and IRQ for macb0
ARM: dts: at91: sama5d2 xplained: add phy address and IRQ for macb0
ARM: dts: at91: at91sam9n12ek: fix panel compatible string
ARM: dts: at91: sama5d4: fix instance id of DBGU
Signed-off-by: Olof Johansson <olof@lixom.net>
This platform recently moved to multi-platform, so missed the global
fixup by commit e324654294 ("ARM: use "depends on" for SoC configs
instead of "if" after prompt"). Fix it now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This platform was recently added, so missed the global fixup by
commit e324654294 ("ARM: use "depends on" for SoC configs instead
of "if" after prompt"). Fix it now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This newly added code missed the global fixup by commit 75305275a7
("ARM: use const and __initconst for smp_operations"). So fix it now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This newly added code missed the global fixup by commit 75305275a7
("ARM: use const and __initconst for smp_operations"). So fix it now.
Also, add missing "static" qualifier.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Update Eth PHY settings to make it possible to run both phys at 1Gbps.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On-board SPI flash cat act at 48Mhz SPI bus frequency.
Update the DT frequency property.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Revert commit 7cd6ca770d ("ARM: dts: Change I2C2 and I2C3 to 400KHz
for LogicPD Torpedo DM3730 devkit") It was already done and it is
just a duplicate.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now IRQs for Pixcir Tangoc touchscreen are defined using
IRQ_TYPE_NONE in am437x-gp-evm.dts and am43x-epos-evm.dts wich
do not correspond HW.
Hence, update am437x-gp-evm.dts and am43x-epos-evm.dts files
and use correct flag IRQ_TYPE_EDGE_FALLING for irq types.
While here, remove duplicated irq declaration for pixcir_ts@5c node
in am437x-gp-evm.dts.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per ARM documentation
PPI(0) ID27 - global timer interrupt is rising-edge sensitive.
PPI(2) ID29 - twd interrupt is rising-edge sensitive.
and the same is proved by GIC distributor register value
GIC_DIST_CONFIG(0xC04) = 0x7DC00000.
Hence, set IRQ triggering type to IRQ_TYPE_EDGE_RISING
for ARM TWD and Global timers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For phy0 KSZ8081, the type of GPIO IRQ should be "level low" instead of
"edge falling".
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes: 38153a0178 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Cc: <stable@vger.kernel.org> # 4.1+
No interrupt were received from the phy because PIOE 1 may not be properly
muxed. It prevented proper link detection, especially since commit
321beec504 ("net: phy: Use interrupts when available in NOLINK state")
disables polling.
Cc: <stable@vger.kernel.org> # 4.4
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
On SAMA5D4EK board, the Ethernet doesn't work after resuming from the suspend
state.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
[nicolas.ferre@atmel.com: adapt to newer kernel]
Fixes: 38153a0178 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Cc: <stable@vger.kernel.org> # 4.1+
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
After 57a38effa5 (net: phy: micrel: disable broadcast for KSZ8081/KSZ8091)
the macb0 interface has difficulties to come back from power saving mode if
address not explicitly set up.
As the micrel phy on the board is actually configured to show up at address 1
we use this explicitly.
Adding the phy node and its real address fixes the issue.
The phy IRQ and associated pinmux node is also added.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: stable@vger.kernel.org # 4.4+ // manual merge needed
Properly use qiaodian as the vendor prefix for the panel.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Building with CONFIG_CC_STACKPROTECTOR_STRONG triggers protection code
generation under CONFIG_ARM_ATAG_DTB_COMPAT but this is too early for
being able to use any of the stack_chk code. Explicitly disable it for
only the atags_to_fdt bits.
Suggested-by: zhxihu <zhxihu@marvell.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The tcxo-clock-frequency binding is listed as optional,
but without it the wl12xx used on the torpedo + wireless
may hang. Scanning also appears broken without this patch.
Signed-off-by: Adam Ford <aford173@gmail.com>
Fixes: 687c276761 ("ARM: dts: Add minimal support for LogicPD
Torpedo DM3730 devkit")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to set the currently platform dependent dmtimer
functions pointers as platform data for the pwm-omap-dmtimer
platform driver, add it to plat-omap auxdata_lookup table.
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Here're a few gpio pin related fixes:
- remove pinctrl-0 definition from pinctrl, since those pins are used
in other places such as gpio-fan and regulators.
- keep initial state of power led
- fix for alarm pin of gpio-fan.
Fixes: dc57844a73 ("ARM: dts: orion5x: add buffalo linkstation ls-wtgl")
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
For kirkwood, gpio pins starts from 32 are in the 2nd bank, so it should be
converted to "gpio1 <pin minus 32>" in dts file.
e.g. gpio 40 should be "gpio1 8"
The pin/bank issue was found when discussing Debian Bug #810894
[https://bugs.debian.org/810894#47]
Fixes: c43379e150 ("ARM: dts: add buffalo linkstation ls-wvl/vl")
Reported-by: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
For kirkwood, gpio pins starts from 32 are in the 2nd bank, so it should be
converted to "gpio1 <pin minus 32>" in dts file.
e.g. gpio 40 should be "gpio1 8"
Besides, a few other pin fixes for ls-wxl/wsxl, to match with mpp pin
definition:
- gpio-leds: "lswxl:blue:power" pin
- gpio-leds: "lswxl:red:func" pin
- gpio-leds: "lswxl:red:hdderr0" pin
- gpio-leds: "lswxl:red:hdderr1" pin
- gpio-fan: low/high/alarm pin
The pin/bank issue was found when discussing Debian Bug #810894
[https://bugs.debian.org/810894#47]
Fixes: e54e4b1b62 ("ARM: dts: add buffalo linkstation ls-wxl/wsxl")
Reported-by: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As of commit e488ca9f8d ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As of commit e488ca9f8d ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Merge small final update from Andrew Morton:
- DAX feature work: add fsync/msync support
- kfree cleanup, MAINTAINERS update
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
MAINTAINERS: return arch/sh to maintained state, with new maintainers
tree wide: use kvfree() than conditional kfree()/vfree()
dax: never rely on bh.b_dev being set by get_block()
xfs: call dax_pfn_mkwrite() for DAX fsync/msync
ext4: call dax_pfn_mkwrite() for DAX fsync/msync
ext2: call dax_pfn_mkwrite() for DAX fsync/msync
dax: add support for fsync/sync
mm: add find_get_entries_tag()
dax: support dirty DAX entries in radix tree
pmem: add wb_cache_pmem() to the PMEM API
dax: fix conversion of holes to PMDs
dax: fix NULL pointer dereference in __dax_dbg()
Here's a single-SoC topic branch that we've staged separately. Mainly
because it was hard to sort the branch contents in a way that fit our
existing branches due to some refactorings.
The code has been in -next for quite a while, but we staged it in arm-soc
a bit late, which is why we've kept it separate from the other updates
and are sending it separately here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LG3u
-----END PGP SIGNATURE-----
Merge tag 'armsoc-tegra' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC support for Tegra platforms from Olof Johansson:
"Here's a single-SoC topic branch that we've staged separately. Mainly
because it was hard to sort the branch contents in a way that fit our
existing branches due to some refactorings.
The code has been in -next for quite a while, but we staged it in
arm-soc a bit late, which is why we've kept it separate from the other
updates and are sending it separately here"
* tag 'armsoc-tegra' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: tegra: Add NVIDIA Jetson TX1 Developer Kit support
arm64: tegra: Add NVIDIA P2597 I/O board support
arm64: tegra: Add NVIDIA Jetson TX1 support
arm64: tegra: Add NVIDIA P2571 board support
arm64: tegra: Add NVIDIA P2371 board support
arm64: tegra: Add NVIDIA P2595 I/O board support
arm64: tegra: Add NVIDIA P2530 main board support
arm64: tegra: Add Tegra210 support
arm64: tegra: Add NVIDIA Tegra132 Norrin support
arm64: tegra: Add Tegra132 support
ARM: tegra: select USB_ULPI from EHCI rather than platform
ARM: tegra: Ensure entire dcache is flushed on entering LP0/1
amba: Hide TEGRA_AHB symbol
soc/tegra: Add Tegra210 support
soc/tegra: Provide per-SoC Kconfig symbols
A few fixes for fallout that we didn't catch in time in -next, or smaller
warning fixes that have been discovered since.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PRjJ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes for fallout that we didn't catch in time in -next, or
smaller warning fixes that have been discovered since"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
soc: qcom/spm: shut up uninitialized variable warning
ARM: realview: fix device tree build
ARM: debug-ll: fix BCM63xx entry for multiplatform
ARM: dts: armadillo800eva Correct extal1 frequency to 24 MHz
There are many locations that do
if (memory_was_allocated_by_vmalloc)
vfree(ptr);
else
kfree(ptr);
but kvfree() can handle both kmalloc()ed memory and vmalloc()ed memory
using is_vmalloc_addr(). Unless callers have special reasons, we can
replace this branch with kvfree(). Please check and reply if you found
problems.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Jan Kara <jack@suse.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Acked-by: David Rientjes <rientjes@google.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Boris Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correct extal1 frequency of armadillo800eva board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YGew
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Renesas ARM Based SoC Fixes for v4.5
Correct extal1 frequency of armadillo800eva board
* tag 'renesas-fixes-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: armadillo800eva Correct extal1 frequency to 24 MHz
Signed-off-by: Olof Johansson <olof@lixom.net>
With recent omap assembly fixes for CONFIG_DEBUG_RODATA, we can
now use DEBUG_RODATA. Let's enable ARM_KERNMEM_PERMS so that
DEBUG_RODATA gets selected by default. This way we can make sure
any related issues are caught early.
And while testing things on various devices, I noticed we're
missing few loadable modules to make things more usable:
- USB Ethernet for smsc75xx, we only have smsc97xx right now
- Basic USB serial drivers for things like ftdi and pl2303 ports
- Blinking leds with pca963x
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't want to write to .text so let's move ppa_zero_params and
ppa_por_params to .data and access them via pointers.
Note that I have not been able to test as we I don't have a HS
omap4 to test with. The code has been changed in similar way as
for omap3 though.
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # v4.0+
Fixes: 1e6b48116a ("ARM: mm: allow non-text sections to be
non-executable")
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't want to write to .text, so let's move l2_inv_api_params
to .data and access it via a pointer.
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # v4.0+
Fixes: 1e6b48116a ("ARM: mm: allow non-text sections to be
non-executable")
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't want to write to .text and we can move save_secure_ram_context
into .data as it all gets copied into SRAM anyways.
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # v4.0+
Fixes: 1e6b48116a ("ARM: mm: allow non-text sections to be
non-executable")
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't want to write to .text section. Let's move l2dis_3630
to .data and access it via a pointer.
For calculating the offset, let's optimize out the add and do it
in ldr/str as suggested by Nicolas Pitre <nicolas.pitre@linaro.org>.
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: stable@vger.kernel.org # v4.0+
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # v4.0+
Fixes: 1e6b48116a ("ARM: mm: allow non-text sections to be
non-executable")
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't want to be writing to .text so it can be set rodata.
Fix error "Unable to handle kernel paging request at virtual address
c012396c" in wait_dll_lock_timed if CONFIG_DEBUG_RODATA is selected.
As these counters are for debugging only and unused, we can just
remove them.
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # v4.0+
Fixes: 1e6b48116a ("ARM: mm: allow non-text sections to be
non-executable")
Signed-off-by: Tony Lindgren <tony@atomide.com>
The legacy-style mailbox device creation is supported currently
only for OMAP3, as all other SoCs are DT-boot only. Even on this
SoC, there are no client drivers that utilize these mailbox devices.
So, clean up the legacy-style mailbox device instantiation logic.
The mailbox devices are already present and supported for the DT
boot on OMAP3.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add ti,mbox-send-noirq to wkup_m3 mailbox so that messages using
wkup_m3 mailbox are sent without triggering any further interrupts.
This is required to be able to send multiple messages to the WkupM3
after the mailbox usage logic adjustment in the wkup_m3_ipc driver.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Dave Gerlach <d-gerlach@ti.com>
[s-anna@ti.com: revise commit description]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add ti,mbox-send-noirq to wkup_m3 mailbox so that messages using
wkup_m3 mailbox are sent without triggering any further interrupts.
This is needed to achieve lower power numbers during CPU idle on
AM33xx.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[s-anna@ti.com: revise commit description]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dinh Nguyen