No functional changes; just renaming a bit, tweaking a datatype,
prettifying layout, and adding comments, in particular in the
GuC setup code that touches this data.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473711577-11454-2-git-send-email-david.s.gordon@intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Since the watermark calculations for Skylake are still broken, we're apt
to hitting underruns very easily under multi-monitor configurations.
While it would be lovely if this was fixed, it's not. Another problem
that's been coming from this however, is the mysterious issue of
underruns causing full system hangs. An easy way to reproduce this with
a skylake system:
- Get a laptop with a skylake GPU, and hook up two external monitors to
it
- Move the cursor from the built-in LCD to one of the external displays
as quickly as you can
- You'll get a few pipe underruns, and eventually the entire system will
just freeze.
After doing a lot of investigation and reading through the bspec, I
found the existence of the SAGV, which is responsible for adjusting the
system agent voltage and clock frequencies depending on how much power
we need. According to the bspec:
"The display engine access to system memory is blocked during the
adjustment time. SAGV defaults to enabled. Software must use the
GT-driver pcode mailbox to disable SAGV when the display engine is not
able to tolerate the blocking time."
The rest of the bspec goes on to explain that software can simply leave
the SAGV enabled, and disable it when we use interlaced pipes/have more
then one pipe active.
Sure enough, with this patchset the system hangs resulting from pipe
underruns on Skylake have completely vanished on my T460s. Additionally,
the bspec mentions turning off the SAGV with more then one pipe enabled
as a workaround for display underruns. While this patch doesn't entirely
fix that, it looks like it does improve the situation a little bit so
it's likely this is going to be required to make watermarks on Skylake
fully functional.
This will still need additional work in the future: we shouldn't be
enabling the SAGV if any of the currently enabled planes can't enable WM
levels that introduce latencies >= 30 µs.
Changes since v11:
- Add skl_can_enable_sagv()
- Make sure we don't enable SAGV when not all planes can enable
watermarks >= the SAGV engine block time. I was originally going to
save this for later, but I recently managed to run into a machine
that was having problems with a single pipe configuration + SAGV.
- Make comparisons to I915_SKL_SAGV_NOT_CONTROLLED explicit
- Change I915_SAGV_DYNAMIC_FREQ to I915_SAGV_ENABLE
- Move printks outside of mutexes
- Don't print error messages twice
Changes since v10:
- Apparently sandybridge_pcode_read actually writes values and reads
them back, despite it's misleading function name. This means we've
been doing this mostly wrong and have been writing garbage to the
SAGV control. Because of this, we no longer attempt to read the SAGV
status during initialization (since there are no helpers for this).
- mlankhorst noticed that this patch was breaking on some very early
pre-release Skylake machines, which apparently don't allow you to
disable the SAGV. To prevent machines from failing tests due to SAGV
errors, if the first time we try to control the SAGV results in the
mailbox indicating an invalid command, we just disable future attempts
to control the SAGV state by setting dev_priv->skl_sagv_status to
I915_SKL_SAGV_NOT_CONTROLLED and make a note of it in dmesg.
- Move mutex_unlock() a little higher in skl_enable_sagv(). This
doesn't actually fix anything, but lets us release the lock a little
sooner since we're finished with it.
Changes since v9:
- Only enable/disable sagv on Skylake
Changes since v8:
- Add intel_state->modeset guard to the conditional for
skl_enable_sagv()
Changes since v7:
- Remove GEN9_SAGV_LOW_FREQ, replace with GEN9_SAGV_IS_ENABLED (that's
all we use it for anyway)
- Use GEN9_SAGV_IS_ENABLED instead of 0x1 for clarification
- Fix a styling error that snuck past me
Changes since v6:
- Protect skl_enable_sagv() with intel_state->modeset conditional in
intel_atomic_commit_tail()
Changes since v5:
- Don't use is_power_of_2. Makes things confusing
- Don't use the old state to figure out whether or not to
enable/disable the sagv, use the new one
- Split the loop in skl_disable_sagv into it's own function
- Move skl_sagv_enable/disable() calls into intel_atomic_commit_tail()
Changes since v4:
- Use is_power_of_2 against active_crtcs to check whether we have > 1
pipe enabled
- Fix skl_sagv_get_hw_state(): (temp & 0x1) indicates disabled, 0x0
enabled
- Call skl_sagv_enable/disable() from pre/post-plane updates
Changes since v3:
- Use time_before() to compare timeout to jiffies
Changes since v2:
- Really apply minor style nitpicks to patch this time
Changes since v1:
- Added comments about this probably being one of the requirements to
fixing Skylake's watermark issues
- Minor style nitpicks from Matt Roper
- Disable these functions on Broxton, since it doesn't have an SAGV
Signed-off-by: Lyude <cpaul@redhat.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471463761-26796-3-git-send-email-cpaul@redhat.com
[mlankhorst: ENOSYS -> ENXIO, whitespace fixes]
In order to add proper support for the SAGV, we need to be able to know
what the cause of a failure to change the SAGV through the pcode mailbox
was. The reasoning for this is that some very early pre-release Skylake
machines don't actually allow you to control the SAGV on them, and
indicate an invalid mailbox command was sent.
This also might come in handy in the future for debugging.
Changes since v1:
- Add functions for interpreting gen6 mailbox error codes along with
gen7+ error codes, and actually interpret those codes properly
- Renamed patch to reflect new behavior
Signed-off-by: Lyude <cpaul@redhat.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471463761-26796-2-git-send-email-cpaul@redhat.com
[mlankhorst: -ENOSYS -> -ENXIO for checkpatch]
Atm the LVDS encoder depends on the PPS HW context being saved/restored
from generic suspend/resume code. Since the PPS is specific to the LVDS
and eDP encoders a cleaner way is to reinitialize it during encoder
enabling, so do this here for LVDS. Follow-up patches will init the PPS
for the eDP encoder similarly and remove the suspend/resume time save /
restore.
v2:
- Apply BSpec +1 offset and use DIV_ROUND_UP() when programming the
power cycle delay. (Ville)
v3: (Ville)
- Fix +1 vs. round-up order.
- s/reset_on_powerdown/powerdown_on_reset/
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470827254-21954-3-git-send-email-imre.deak@intel.com
The PPS registers are pretty much the same everywhere, the differences
being:
- Register fields appearing, disappearing from one platform to the
next: panel-reset-on-powerdown, backlight-on, panel-port,
register-unlock
- Different register base addresses
- Different number of PPS instances: 2 on VLV/CHV/BXT, 1 everywhere
else.
We can merge the separate set of PPS definitions by extending the PPS
instance argument to all platforms and using instance 0 on platforms
with a single instance. This means we'll need to calculate the register
addresses dynamically based on the given platform and PPS instance.
v2:
- Simplify if ladder in intel_pps_get_registers(). (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470827254-21954-1-git-send-email-imre.deak@intel.com
Since commit de1add3605 ("drm/i915: Decouple execbuf uAPI from internal
implementation") the index of the engine (its engine->id) in the
internal list no longer matches the hardware id. However, in a couple of
locations we missed fixing up the difference. In this case,
RING_FAULT_REG() refers to engine->id which is now not what the register
offset actually should be. Fortunately, in both case we should be more
or less looping over 0..I915_NUM_ENGINES.
Fixes: de1add3605 ("drm/i915: Decouple execbuf uAPI from internal...")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469643077-2523-2-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org
Updated the i915_drpc_info debugfs with coarse power gating & forcewake
info for Gen9.
v2: Change all IS_GEN9() by gen >= 9 (Damien)
v3: Rebase
Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1467038401-8283-1-git-send-email-akash.goel@intel.com
Bspec says:
"For DDIA with x4 capability (DDI_BUF_CTL DDIA Lane Capability Control =
DDIA x4), the I_boost value has to be programmed in both
tx_blnclegsctl_0 and tx_blnclegsctl_4."
Currently we only program tx_blnclegsctl_0. Let's do the other one as
well.
Cc: stable@vger.kernel.org
Fixes: f8896f5d58 ("drm/i915/skl: Buffer translation improvements")
Cc: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1468328376-6380-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
'ring' is an old deprecated term for a GPU engine. Here we make the
terminology more consistent by renaming the 'ring' parameter of lots of
macros that calculate addresses within the MMIO space of an engine.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469034967-15840-2-git-send-email-david.s.gordon@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add WaDisableGatherAtSetShaderCommonSlice for all gen9 as stated
by bspec. The bspec told to put this workaround to the per ctx bb.
Initial implementation and subsequent review were done based on
bspec. Arun raised a suspicion that this would belong to indirect bb
instead and he conducted more throughout investigation on the matter
and indeed the documentation was wrong.
v2: Move to indirect_ctx wa bb, as it is correct place (Arun)
References: HSD#2135817
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com> (v1)
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469013973-24104-1-git-send-email-mika.kuoppala@intel.com
Add this workaround to prevent hang when in place compression
is used.
References: HSD#2135774
Cc: stable@vger.kernel.org
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
BXT BIOS has two options related to GPU power management: "RC6(Render
Standby)" and "GT PM Support". The assumption so far was that disabling
either of these options would leave RC6 uninitialized. According to my
tests this isn't so: for a proper RC6 setup we only need the "GT PM
Support" option to be enabled while the "RC6" option only controls
whether RC6 is left enabled or not by BIOS. OTOH we were missing a few
checks to ensure a proper RC6 setup. Add these now and don't fail the
sanity check if RC6 is disabled. This fixes a problem where RC6 remains
disabled after reloading the driver, since we explicitly disable RC6
during unloading.
v2:
- Print a debug message about the BIOS enabled RC state. (Sagar)
CC: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467216835-1086-2-git-send-email-imre.deak@intel.com
Currently the addressing mode bit in context descriptor is statically
generated from the configuration of system-wide PPGTT usage model.
GVT-g will load the PPGTT shadow page table by itself and probably one
guest is using a different addressing mode with i915 host. The addressing
mode bits of a LRC context should be configurable under this case.
v10:
- Fix the identation. (Joonas)
v9:
- Rename the data member in struct i915_gem_context. (Chris)
v8:
- Rename the data member in struct i915_gem_context. (Chris)
v7:
- Move context addressing mode bit into i915_reg.h. (Joonas/Chris)
- Add prefix "INTEL_" for related definitions. (Joonas)
v6:
- Directly save the addressing mode bits inside i915_gem_context. (Chris)
- Move the LRC context addressing mode bits into intel_lrc.h. (Chris)
v5:
- Change USES_FULL_48BIT(dev) to USES_FULL_48BIT(dev_priv) (Tvrtko)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v9)
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1466078825-6662-7-git-send-email-zhi.a.wang@intel.com
Backmerge drm-next to get at the nonblocking atomic helpers, needed to
merge the i915 conversion.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This is a WA affecting pooled eu which is a bxt specific feature.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Winiarski, Michal <michal.winiarski@intel.com>
Cc: Zou, Nanhai <nanhai.zou@intel.com>
Cc: Yang, Rong R <rong.r.yang@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
This mode allows to assign EUs to pools which can process work collectively.
The command to enable this mode should be issued as part of context initialization.
The pooled mode is global, once enabled it has to stay the same across all
contexts until HW reset hence this is sent in auxiliary golden context batch.
Thanks to Mika for the preliminary review and comments.
v2: explain why this is enabled in golden context, use feature flag while
enabling the support (Chris)
v3: Include only kernel support as userspace support is not available yet.
User space clients need to know when the pooled EU feature is present
and enabled on the hardware so that they can adapt work submissions.
Create a new device info flag for this purpose.
Set has_pooled_eu to true in the Broxton static device info - Broxton
supports the feature in hardware and the driver will enable it by
default.
We need to add getparam ioctls to enable userspace to query availability of
this feature and to retrieve min. no of eus in a pool but we will expose
them once userspace support is available. Opensource users for this feature
are mesa, libva and beignet.
Beignet team is currently working on adding userspace support.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Cc: Winiarski, Michal <michal.winiarski@intel.com>
Cc: Zou, Nanhai <nanhai.zou@intel.com>
Cc: Yang, Rong R <rong.r.yang@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Armin Reese <armin.c.reese@intel.com>
Cc: Tim Gore <tim.gore@intel.com>
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
We can check the power state of the PHY data and common lanes as
reported by the PHY. Do this in case we need to debug problems where the
PHY gets stuck in an unexpected state.
Note that I only check these when the lanes are expected to be powered
on purpose, since it's not clear at what point the PHY power/clock gates
things.
v2:
- Don't report the encoder as disabled when the sanity check fails.
(Ville)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465825477-32671-1-git-send-email-imre.deak@intel.com
So far we depended on the HW to dynamically power down unused PHYs and
so we enabled them manually once during driver loading/resuming. There
are indications however that we can achieve better power savings by
manual powering toggling. So make the PHY enabling/disabling to happen
on-demand whenever we need either the corresponding AUX or port
functionality. CHV does this already by enabling the PHY along the
corresponding PHY common lane power wells there, do the same on BXT by
adding virtual power wells for the same purpose.
Also sanity check the common lane power down ack signal from the PHY. Do
this only when the PHY is enabled, since it's not clear at what point
the HW power/clock gates things.
While at it rename broxton_ prefix to bxt_ in related function names to
better align with the SKL code.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
This patch enables a workaround for a mid thread preemption
issue where a hardware timing problem can prevent the
context restore from happening, leading to a hang.
v2: move to gen9_init_workarounds (Arun)
v3: move to start of gen9_init_workarounds (Arun)
Signed-off-by: Tim Gore <tim.gore@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465816501-25557-1-git-send-email-tim.gore@intel.com
- some polish for the guc code (Dave Gordon)
- big refactoring of gen9 display clock handling code (Ville)
- refactoring work in the context code (Chris Wilson)
- give encoder/crtc/planes useful names for debug output (Ville)
- improvements to skl/kbl wm computation code (Mahesh Kumar)
- bunch of smaller improvements all over as usual
* tag 'drm-intel-next-2016-06-06' of git://anongit.freedesktop.org/drm-intel: (64 commits)
drm/i915: Update DRIVER_DATE to 20160606
drm/i915: Extract physical display dimensions from VBT
drm/i915: Silence "unexpected child device config size" for VBT on 845g
drm/i915/skl+: Use scaling amount for plane data rate calculation (v4)
drm/i915/skl+: calculate plane pixel rate (v4)
drm/i915/skl+: calculate ddb minimum allocation (v6)
drm/i915: Don't try to calculate relative data rates during hw readout
drm/i915: Only ignore eDP ports that are connected
drm/i915: Update GEN6_PMINTRMSK setup with GuC enabled
drm/i915: kill STANDARD/CURSOR plane screams
drm/i915: Give encoders useful names
drm/i915: Give meaningful names to all the planes
drm/i915: Don't leak primary/cursor planes on crtc init failure
drm/i915: Set crtc->name to "pipe A", "pipe B", etc.
drm/i915: Use plane->name in debug prints
drm/i915: Use crtc->name in debug messages
drm/i915: Reject modeset if the dotclock is too high
drm/i915: Fix NULL pointer deference when out of PLLs in IVB
drm/i915/ilk: Don't disable SSC source if it's in use
drm/i915/bxt: Sanitize CDCLK to fix breakage during S4 resume
...
Bspec states that we need to set nuke on modify all to prevent
screen corruption with fbc on skl and kbl.
v2: proper workaround name
References: HSD#2227109, HSDES#1404569388
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-27-git-send-email-mika.kuoppala@intel.com
Set bit 8 in 0x43224 to prevent screen corruption and system
hangs on high memory bandwidth conditions. The same wa also suggest
setting bit 31 on ARB_CTL. According to another workaround we gain
better idle power savings when FBC is enabled.
v2: use correct workaround name
v3: split out overlapping wa for corruption avoidance (Ville)
References: HSD#2137218, HSD#2227171, HSD#2136579, BSID#883
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-26-git-send-email-mika.kuoppala@intel.com
According to bspec this workaround helps to reduce lag and improve
performance on edp.
Documentation suggests this for bdw and all gen9. However evidence
shows that this register is missing on gen9 and causing unclaimed mmio
access if we access it. So apply to bdw only where the reg
exists and can hold its value.
v2: drop skl
References: HSD#2134579
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-11-git-send-email-mika.kuoppala@intel.com
We need to disable clock gating in this unit to work around
hardware issue causing possible corruption/hang.
v2: name the bit (Ville)
v3: leave the fix enabled for 2227050 and set correct bit (Matthew)
References: HSD#2227156, HSD#2227050
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-2-git-send-email-mika.kuoppala@intel.com
Fix the failure mode where the display appears split, or shifted about
2/3 of the screen, and the color components are cycled. Turns out we
were missing the crucial BXT_DEFEATURE_DPI_FIFO_CTR bit in the
EOT_DISABLE register.
Per bspec, with the bit set, the "mipi_dpf_vblank_start" signal is
asserted only when the complete frame is transferred in the DPHY line
and also the DPI FIFO is flushed out at the end of each frame.
The problem was mitigated by keeping the panel fitter enabled, but that
only limited the issue to a shift of about 0..10 pixels. With the fix
here, the panel fitter workaround does not seem to be needed at all.
While at it, set BXT_DPHY_DEFEATURE_EN in EOT_DISABLE register which is
also needed per the BXT DSI mode set sequence.
Issue: VIZ-7610
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464965825-31035-1-git-send-email-jani.nikula@intel.com
Just fallout from switching from asciidoc to sphinx/rst.
v2: Found more. Also s/\//#/ in the vgpu ascii-art - sphinx treats
those as comments and switch to variable-width, which wreaks the
layout.
v3: Undo some of the hacks, rebasing onto latest version of Jani's
series fixed it.
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
On Loading, GuC sets PM interrupts routing (bit 31) and clears ARAT
expired interrupt (bit 9). Host turbo also updates this register
in RPS flows. This patch ensures bit 31 and bit 9 setup by GuC persists.
ARAT timer interrupt is needed in GuC for various features. It also
facilitates halting GuC and hence achieving RC6. PM interrupt routing
will not impact RPS interrupt reception by host as GuC will redirect
them.
This patch fixes igt test pm_rc6_residency that was failing with guc
load/submission enabled. Tested with SKL GuC v6.1 and BXT GuC v5.1 and v8.7.
v2: i915_irq/i915_pm decoupling from intel_guc. (ChrisW)
v3: restructuring the mask update and rebase w.r.t Ville's patch. (ChrisW)
v4: Updating the pm_intr_keep during direct_interrupts_to_guc. (Sagar)
Cc: Chris Harris <chris.harris@intel.com>
Cc: Zhe Wang <zhe1.wang@intel.com>
Cc: Deepak S <deepak.s@intel.com>
Cc: Satyanantha, Rama Gopal M <rama.gopal.m.satyanantha@intel.com>
Cc: Akash Goel <akash.goel@intel.com>
Testcase: igt/pm_rc6_residency
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Tested-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464683307-19475-1-git-send-email-sagar.a.kamble@intel.com
Found this while browsing Bspec. Looks like it applies to both skl and
kbl.
v2: Also for bxt (Art).
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Cc: "Runyan, Arthur J" <arthur.j.runyan@intel.com>
Reviewed-by: Sonika Jindal<sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463642060-30728-1-git-send-email-daniel.vetter@ffwll.ch
BXT could change the CD2X divider synchronized with a single pipe.
So assuming the DE PLL frequency doesn't need to be changed, we could
change cdclk without shutting off the pipe (when only a single pipe is
enabled). In the meantime let's configure CDCLK_CTL for non-double
buffered CD2X update, although it shouldn't really matter as long as
the selected pipe is disabled when reprogramming the divider.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-13-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
While browsing BSpec I bumped into a note saying we need to tune these
values based on actual measurements done after initial enabling. I've
checked that it indeed improves things on BXT. I haven't checked this on
CHV, but here it is if someone wants to give it a go.
v2:
- Add note about the discrepancy wrt. to the spec in the formula
calculating the credit encodings. (Mika, Ville)
- Move the WA comment to the new function. (Ville)
v3:
- Keep the comment about the SQC WA in the caller. (Ville)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462280061-1457-4-git-send-email-imre.deak@intel.com
No need for hard-coding the register value, the corresponding fields are
defined properly in BSpec.
No functional change.
v2:
- Rebased on BXT L3 SQC tuning patch merged meanwhile.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1462280061-1457-3-git-send-email-imre.deak@intel.com
Update CDCLK_FREQ on BDW after changing the cdclk frequency. Not sure
if this is a late addition to the spec, or if I simply overlooked this
step when writing the original code.
This is what Bspec has to say about CDCLK_FREQ:
"Program this field to the CD clock frequency minus one. This is used to
generate a divided down clock for miscellaneous timers in display."
And the "Broadwell Sequences for Changing CD Clock Frequency" section
clarifies this further:
"For CD clock 337.5 MHz, program 337 decimal.
For CD clock 450 MHz, program 449 decimal.
For CD clock 540 MHz, program 539 decimal.
For CD clock 675 MHz, program 674 decimal."
Cc: stable@vger.kernel.org
Cc: Mika Kahola <mika.kahola@intel.com>
Fixes: b432e5cfd5 ("drm/i915: BDW clock change support")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461689194-6079-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
I just noticed that VLV/CHV have a RAWCLK_FREQ register just like PCH
platforms. It lives in the display power well, so we should update it
when enabling the power well.
Interestingly the BIOS seems to leave it at the reset value (125) which
doesn't match the rawclk frequency on VLV/CHV (200 MHz). As always with
these register, the spec is extremely vague what the register does. All
it says is: "This is used to generate a divided down clock for
miscellaneous timers in display." Based on a quick test, at least AUX
and PWM appear to be unaffected by this.
But since the register is there, let's configure it in accordance with
the spec.
Note that we have to move intel_update_rawclk() to occur before we
touch the power wells, so that the dev_priv->rawclk_freq is already
populated when the disp2 enable hook gets called for the first time.
I think this should be safe to do on other platforms as well.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461768202-17544-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This patch applies a performance enhancement workaround
based on analysis of DX and OCL S-Curve workloads. We
increase the General Priority Credits for L3SQ from the
hardware default of 56 to the max value 62, and decrease
the High Priority credits from 8 to 2.
v2: Only apply to B0 onwards
v3: Move w/a to per engine init, ie bxt_init_workarounds
Signed-off-by: Tim Gore <tim.gore@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461314761-36854-1-git-send-email-tim.gore@intel.com
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Added a new GT_PM_INTERVAL_TO_US macro to perform the platform
specific conversion of PM time interval values to microseconds unit.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461350146-23454-1-git-send-email-akash.goel@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Somehow my SNB GT1 (Dell XPS 8300) gets very unhappy around
GPU hangs if the RPS EI/thresholds aren't suitably aligned.
It seems like scheduling/timer interupts stop working somehow
and things get stuck eg. in usleep_range().
I bisected the problem down to
commit 8a5864377b ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
I observed that before all the values were at least multiples of 25,
but afterwards they are not. And rounding things up to the next multiple
of 25 does seem to help, so lets' do that. I also tried roundup(..., 5)
but that wasn't sufficient. Also I have no idea if we might need this sort of
thing on gen9+ as well.
These are the original EI/thresholds:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10250
GEN6_RP_UP_THRESHOLD 9225
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 8000
GEN6_RP_UP_THRESHOLD 6800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
These are after 8a5864377b12:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10156
GEN6_RP_UP_THRESHOLD 9140
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7812
GEN6_RP_UP_THRESHOLD 6640
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
And these are what we have after this patch:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10175
GEN6_RP_UP_THRESHOLD 9150
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7825
GEN6_RP_UP_THRESHOLD 6650
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
Cc: stable@vger.kernel.org
Cc: Akash Goel <akash.goel@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Testcase: igt/kms_pipe_crc_basic/hang-read-crc-pipe-B
Fixes: 8a5864377b ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461159836-9108-1-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Do not use magic numbers, do not prefix stuff with "PCI_", do not
declare registers in implementation files. Also move the PCI
registers under correct comment in i915_reg.h.
v2:
- Consistently use BSM (not BDSM or other variants from PRM) (Chris)
- Also include register address to help identify the register (Chris)
v3:
- Refer to register value as *_val instead of *_reg (Chris)
v4:
- Make style checker happy
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
This has been corrected in BSpec quite some time ago, but we missed it
somehow. The wrong field definitions resulted in configuring PHY0 with
an incorrect GRC value.
v2:
- Remove the FIXME comment, we left in the code exactly about this
issue. (Ville)
CC: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-3-git-send-email-imre.deak@intel.com
Dave Gordon