In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Arvid Brodin <arvid.brodin@alten.se>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When HSR interface is setup using ip link command, an annoying warning
appears with the trace as below:-
[ 203.019828] hsr_get_node: Non-HSR frame
[ 203.019833] Modules linked in:
[ 203.019848] CPU: 0 PID: 158 Comm: sd-resolve Tainted: G W 4.12.0-rc3-00052-g9fa6bf70 #2
[ 203.019853] Hardware name: Generic DRA74X (Flattened Device Tree)
[ 203.019869] [<c0110280>] (unwind_backtrace) from [<c010c2f4>] (show_stack+0x10/0x14)
[ 203.019880] [<c010c2f4>] (show_stack) from [<c04b9f64>] (dump_stack+0xac/0xe0)
[ 203.019894] [<c04b9f64>] (dump_stack) from [<c01374e8>] (__warn+0xd8/0x104)
[ 203.019907] [<c01374e8>] (__warn) from [<c0137548>] (warn_slowpath_fmt+0x34/0x44)
root@am57xx-evm:~# [ 203.019921] [<c0137548>] (warn_slowpath_fmt) from [<c081126c>] (hsr_get_node+0x148/0x170)
[ 203.019932] [<c081126c>] (hsr_get_node) from [<c0814240>] (hsr_forward_skb+0x110/0x7c0)
[ 203.019942] [<c0814240>] (hsr_forward_skb) from [<c0811d64>] (hsr_dev_xmit+0x2c/0x34)
[ 203.019954] [<c0811d64>] (hsr_dev_xmit) from [<c06c0828>] (dev_hard_start_xmit+0xc4/0x3bc)
[ 203.019963] [<c06c0828>] (dev_hard_start_xmit) from [<c06c13d8>] (__dev_queue_xmit+0x7c4/0x98c)
[ 203.019974] [<c06c13d8>] (__dev_queue_xmit) from [<c0782f54>] (ip6_finish_output2+0x330/0xc1c)
[ 203.019983] [<c0782f54>] (ip6_finish_output2) from [<c0788f0c>] (ip6_output+0x58/0x454)
[ 203.019994] [<c0788f0c>] (ip6_output) from [<c07b16cc>] (mld_sendpack+0x420/0x744)
As this is an expected path to hsr_get_node() with frame coming from
the master interface, add a check to ensure packet is not from the
master port and then warn.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the separate paths for frames coming from the outside, and
frames sent from the HSR device, and instead makes all frames go through
hsr_forward_skb() in hsr_forward.c. This greatly improves code readability and
also opens up the possibility for future support of the HSR Interlink device
that is the basis for HSR RedBoxes and HSR QuadBoxes, as well as VLAN
compatibility.
Other improvements:
* A reduction in the number of times an skb is copied on machines without
HAVE_EFFICIENT_UNALIGNED_ACCESS, which improves throughput somewhat.
* Headers are now created using the standard eth_header(), and using the
standard hard_header_len.
* Each HSR slave now gets its own private skb, so slave-specific fields can be
correctly set.
Signed-off-by: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
High-availability Seamless Redundancy ("HSR") provides instant failover
redundancy for Ethernet networks. It requires a special network topology where
all nodes are connected in a ring (each node having two physical network
interfaces). It is suited for applications that demand high availability and
very short reaction time.
HSR acts on the Ethernet layer, using a registered Ethernet protocol type to
send special HSR frames in both directions over the ring. The driver creates
virtual network interfaces that can be used just like any ordinary Linux
network interface, for IP/TCP/UDP traffic etc. All nodes in the network ring
must be HSR capable.
This code is a "best effort" to comply with the HSR standard as described in
IEC 62439-3:2010 (HSRv0).
Signed-off-by: Arvid Brodin <arvid.brodin@xdin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kees Cook