Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
Here's the big tty/serial driver patchset for 3.18-rc1.
Lots of little things in here, some good work from Peter Hurley on the
tty core, and in lots of drivers. There are also lots of other driver
updates in here as well, full details in the changelog below.
All have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlQ0aDwACgkQMUfUDdst+ymueACeI1i2exlGaBBSVQuUK2Jmx8Uz
nukAn3KPuvvx+MKfMMBRpK0DQCzTxv4P
=dwv1
-----END PGP SIGNATURE-----
Merge tag 'tty-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the big tty/serial driver patchset for 3.18-rc1.
Lots of little things in here, some good work from Peter Hurley on the
tty core, and in lots of drivers. There are also lots of other driver
updates in here as well, full details in the changelogs.
All have been in the linux-next tree for a while"
* tag 'tty-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (99 commits)
Revert "serial/core: Initialize the console pm state"
tty: serial: 8250: use 32bit variable for rpm_tx_active
tty: serial: msm: Add earlycon support
serial/core: Initialize the console pm state
serial: asc: Conditionally use readl_relaxed (COMPILE_TEST)
serial: of-serial: add PM suspend/resume support
m68k: AMIGA_BUILTIN_SERIAL should depend on TTY
asm/uapi: Add definition of TIOC[SG]RS485
tty/metag_da: Add console_poll module parameter
serial: 8250_pci: remove rts_n override from Baytrail quirk
serial: cadence: Add generic earlycon support
serial: imx: change the wait even to interruptiable
serial: imx: terminate the RX DMA when the UART is suspending
serial: imx: fix throttle/unthrottle callbacks for hardware assisted flow control
serial: 8250: Add Quark X1000 to 8250_pci.c
tty: omap-serial: pull out calculation from baud_is_mode16
tty: omap-serial: fix division by zero
xen_hvc: no reason to write the type key on xenstore
tty: serial: 8250_core: remove UART_IER_RDI in serial8250_stop_rx()
tty: serial: 8250_core: use the ->line argument as a hint in serial8250_find_match_or_unused()
...
Cheers,
Rusty.
PS. My virtio-next tree is empty: DaveM took the patches I had. There might
be a virtio-rng starvation fix, but so far it's a bit voodoo so I will
get to that in the next two days or it will wait.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QzCn
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module update from Rusty Russell:
"Nothing major: support for compressing modules, and auto-tainting
params.
PS. My virtio-next tree is empty: DaveM took the patches I had. There
might be a virtio-rng starvation fix, but so far it's a bit voodoo
so I will get to that in the next two days or it will wait"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
moduleparam: Resolve missing-field-initializer warning
kbuild: handle module compression while running 'make modules_install'.
modinst: wrap long lines in order to enhance cmd_modules_install
modsign: lookup lines ending in .ko in .mod files
modpost: simplify file name generation of *.mod.c files
modpost: reduce visibility of symbols and constify r/o arrays
param: check for tainting before calling set op.
drm/i915: taint the kernel if unsafe module parameters are set
module: add module_param_unsafe and module_param_named_unsafe
module: make it possible to have unsafe, tainting module params
module: rename KERNEL_PARAM_FL_NOARG to avoid confusion
It should not be used together with Auto Flow Control, and
Auto Flow Control is always enabled on Baytrail.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quark X1000 contains two designware derived 8250 serial ports.
Each port has a unique PCI configuration space consisting of
BAR0:UART BAR1:DMA respectively.
Unlike the standard 8250 the register width is 32 bits for RHR,IER etc
The Quark UART has a fundamental clock @ 44.2368 MHz allowing for a
bitrate of up to about 2.76 megabits per second.
This patch enables standard 8250 mode
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_startup() adds UART_IER_RDI and UART_IER_RLSI to ier.
serial8250_stop_rx() should remove both.
This is what the serial-omap driver has been doing and is now moved to
the 8250-core since it does no look to be *that* omap specific.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony noticed that the old omap-serial driver picked the uart "number"
based on the hint given from device tree or platform device's id.
The 8250 based omap driver doesn't do this because the core code does
not honour the ->line argument which is passed by the driver.
This patch aims to keep the same behaviour as with omap-serial. The
function will first try to use the line suggested ->line argument and
then fallback to the old strategy in case the port is taken.
That means the the third uart will always be ttyS2 even if the previous
two have not been enabled in DT.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial8250_do_startup() function unconditionally clears the
interrupts and for that it reads from the RX-FIFO without checking if
there is a byte in the FIFO or not. This works fine on OMAP4+ HW like
AM335x or DRA7.
OMAP3630 ES1.1 (which means probably all OMAP3 and earlier) does not like
this:
|Unhandled fault: external abort on non-linefetch (0x1028) at 0xfb020000
|Internal error: : 1028 [#1] ARM
|Modules linked in:
|CPU: 0 PID: 1 Comm: swapper Not tainted 3.16.0-00022-g7edcb57-dirty #1213
|task: de0572c0 ti: de058000 task.ti: de058000
|PC is at mem32_serial_in+0xc/0x1c
|LR is at serial8250_do_startup+0x220/0x85c
|Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
|Control: 10c5387d Table: 80004019 DAC: 00000015
|[<c03051d4>] (mem32_serial_in) from [<c0307fe8>] (serial8250_do_startup+0x220/0x85c)
|[<c0307fe8>] (serial8250_do_startup) from [<c0309e00>] (omap_8250_startup+0x5c/0xe0)
|[<c0309e00>] (omap_8250_startup) from [<c030863c>] (serial8250_startup+0x18/0x2c)
|[<c030863c>] (serial8250_startup) from [<c030394c>] (uart_startup+0x78/0x1d8)
|[<c030394c>] (uart_startup) from [<c0304678>] (uart_open+0xe8/0x114)
|[<c0304678>] (uart_open) from [<c02e9e10>] (tty_open+0x1a8/0x5a4)
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While comparing the OMAP-serial and the 8250 part of this I noticed that
the latter does not use run time-pm. Here are the pieces. It is
basically a get before first register access and a last_busy + put after
last access. This has to be enabled from userland _and_ UART_CAP_RPM is
required for this.
The runtime PM can usually work transparently in the background however
there is one exception to this: After serial8250_tx_chars() completes
there still may be unsent bytes in the FIFO (depending on CPU speed vs
baud rate + flow control). Even if the TTY-buffer is empty we do not
want RPM to disable the device because it won't send the remaining
bytes. Instead we leave serial8250_tx_chars() with RPM enabled and wait
for the FIFO empty interrupt. Once we enter serial8250_tx_chars() with
an empty buffer we know that the FIFO is empty and since we are not going
to send anything, we can disable the device.
That xchg() is to ensure that serial8250_tx_chars() can be called
multiple times and only the first invocation will actually invoke the
runtime PM function. So that the last invocation of __stop_tx() will
disable runtime pm.
NOTE: do not enable RPM on the device unless you know what you do! If
the device goes idle, it won't be woken up by incomming RX data _unless_
there is a wakeup irq configured which is usually the RX pin configure
for wakeup via the reset module. The RX activity will then wake up the
device from idle. However the first character is garbage and lost. The
following bytes will be received once the device is up in time. On the
beagle board xm (omap3) it takes approx 13ms from the first wakeup byte
until the first byte that is received properly if the device was in
core-off.
v5…v8:
- drop RPM from serial8250_set_mctrl() it will be used in
restore path which already has RPM active and holds
dev->power.lock
v4…v5:
- add a wrapper around rpm function and introduce UART_CAP_RPM
to ensure RPM put is invoked after the TX FIFO is empty.
v3…v4:
- added runtime to the console code
- removed device_may_wakeup() from serial8250_set_sleep()
Cc: mika.westerberg@linux.intel.com
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP UART provides support for HW assisted flow control. What is
missing is the support to throttle / unthrottle callbacks which are used
by the omap-serial driver at the moment.
This patch adds the callbacks. It should be safe to add them since they
are only invoked from the serial_core (uart_throttle()) if the feature
flags are set.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new PCI IDs to cover newer Intel SoCs such as Braswell.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
That field has been deprecated in favour of getting the necessary information
from ACPI or DT.
However, we still need to deal systems that are PCI only (no ACPI to back up)
like Intel Bay Trail. In order to support such systems, we explicitly bind
setup() to the appropriate DMA filter function and its corresponding parameter.
Then when serial8250_request_dma() doesn't find the channel via ACPI or DT, it
falls back to use the given filter function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The device has a highspeed register which influences the calcualtion
of the divisor. The chip lacks support for some baudrates. When requested,
we set the divisor to the next smaller baudrate and adjust the c_cflag
accordingly.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit: e676253b19 [3/21] serial/8250: Add
support for RS485 IOCTLs, adds a building error on arch m32r.
All error/warnings:
drivers/tty/serial/8250/8250_core.c: In function 'serial8250_ioctl':
>> drivers/tty/serial/8250/8250_core.c:2859:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
if (copy_from_user(&rs485_config, (void __user *)arg,
^
>> drivers/tty/serial/8250/8250_core.c:2871:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
if (copy_to_user((void __user *)arg, &up->rs485,
^
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Another new ACPI identifier for the 8250 dw bindings to cover newer Intel
SoCs such as Braswell.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP version of the 8250 can actually use 1:1 serial8250_startup().
However it needs to be extended by a wake up irq which should to be
requested & enabled at ->startup() time and disabled at ->shutdown() time.
v2…v3: properly copy callbacks
v1…v2: add shutdown callback
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no way to access a struct uart_8250_port for a specific
line. This is only required outside of the 8250/uart callbacks like for
devices' suspend & remove callbacks. For those the 8250-core provides a
wrapper like serial8250_unregister_port() which passes the struct
to the proper function based on the line argument.
For run time suspend I need access to this struct not only to make
serial_out() work but also to properly restore up->ier and up->mcr.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Existing callers of serial8250_modem_status() [1] hold the uart port
lock; document.
[1] In-tree callers of serial8250_modem_status()
drivers/tty/serial/8250/8250_fsl.c
fsl8250_handle_irq()
drivers/tty/serial/8250/8250_core.c
serial8250_handle_irq()
serial8250_console_write()
serial8250_get_mctrl() *
* Call graphs for callers of serial8250_get_mctrl() from the function
which acquires the uart port lock
drivers/tty/serial/serial_core.c
uart_port_startup()
uart_tiocmget()
uart_set_termios()
uart_carrier_raised()
ops->get_mctrl() ---> serial8250_get_mctrl()
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 06aa82e498.
This commit purports to enable auto CTS flow control for the 8250
UART driver. However, the 8250 UART driver already supports auto
CTS flow control via UART_CAP_AFE and UART_CAP_EFR. Indeed, this
patch introduces another DT attribute for which an existing firmware
flag already exists ("auto-flow-control"). Furthermore, the use of
UPF_HARD_FLOW requires the UART driver to define .throttle and
.unthrottle methods, neither of which are defined for the 8250 UART
driver (which will result in a NULL ptr dereference). Finally, this patch
supposes to fix existing bugs in the serial core for auto CTS-enabled
hardware, but does not include the class of hardware for which these
bugs exist.
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The symbol is defined in drivers/tty/serial/8250/Kconfig as
"SERIAL_8250", not just "8250".
Signed-off-by: Daniele Forsi <dforsi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch lets you set the RS485 cappabilites of the device through
TIOCSRS485 and TIOCGRS485 as defined on Documentation/serial/serial-rs485.txt
In order to probe the device, the PNP id and the device id is used.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch allow the users of the 8250 infrastructure to define a
handler for RS485 configration.
If no handler is defined the 8250 driver will work as usual.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
--
v2:Change suggested by Alan "One Thousand Gnomes":
- Move rs485 structure further down on the uart_8250_port structure
drivers/tty/serial/8250/8250_core.c | 39 +++++++++++++++++++++++++++++++++++++
include/linux/serial_8250.h | 3 +++
2 files changed, 42 insertions(+)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add flags field to struct kernel_params, and add the first flag: unsafe
parameter. Modifying a kernel parameter with the unsafe flag set, either
via the kernel command line or sysfs, will issue a warning and taint the
kernel.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Jon Mason <jon.mason@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The 8250_dw driver fails to probe if the specified clock isn't
registered at probe time. Even if a clock frequency is given,
the required clock might be gated because it wasn't properly
enabled.
This happened to me when the device is registered through DT,
and the clock was part of an MFD, the PRCM found on A31 and A23
SoCs. Unlike core clocks that are registered with OF_CLK_DECLARE,
which happen almost immediately after the kernel starts, the
clocks are registered as sub-devices of the PRCM MFD platform
device. Even though devices are registered in the order they are
found in the DT, the drivers are registered in a different,
arbitrary order. It is possible that the 8250_dw driver is
registered, and thus associated with the device and probed, before
the clock driver is registered and probed.
8250_dw then reports unable to get the clock, and fails. Without
a working console, the kernel panics.
This patch adds support for deferred probe handling for the clock
and reset controller. It also fixes the cleanup path if
serial8250_register_8250_port fails.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Allwinner A31 and A23 SoCs have a reset controller
maintaining the UART in reset by default.
This patch adds optional reset support to the driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add tunable RX interrupt trigger I/F of FIFO buffers.
Serial devices are used as not only message communication devices but control
or sending communication devices. For the latter uses, normally small data
will be exchanged, so user applications want to receive data unit as soon as
possible for real-time tendency. If we have a sensor which sends a 1 byte data
each time and must control a device based on the sensor feedback, the RX
interrupt should be triggered for each data.
According to HW specification of serial UART devices, RX interrupt trigger
can be changed, but the trigger is hard-coded. For example, RX interrupt trigger
in 16550A can be set to 1, 4, 8, or 14 bytes for HW, but current driver sets
the trigger to only 8bytes.
This patch makes some devices change RX interrupt trigger from userland.
<How to use>
- Read current setting
# cat /sys/class/tty/ttyS0/rx_trig_bytes
8
- Write user setting
# echo 1 > /sys/class/tty/ttyS0/rx_trig_bytes
# cat /sys/class/tty/ttyS0/rx_trig_bytes
1
<Support uart devices>
- 16550A and Tegra (1, 4, 8, or 14 bytes)
- 16650V2 (8, 16, 24, or 28 bytes)
- 16654 (8, 16, 56, or 60 bytes)
- 16750 (1, 16, 32, or 56 bytes)
<Change log>
Changes in V9:
- Use attr_group instead of dev_spec_attr_group of uart_port structure
Changes in V8:
- Divide this patch from V7's patch based on Greg's comment
Changes in V7:
- Add Documentation
- Change I/F name from rx_int_trig to rx_trig_bytes because the name
rx_int_trig is hard to understand how users specify the value
Changes in V6:
- Move FCR_RX_TRIG_* definition in 8250.h to include/uapi/linux/serial_reg.h,
rename those to UART_FCR_R_TRIG_*, and use UART_FCR_TRIGGER_MASK to
UART_FCR_R_TRIG_BITS()
- Change following function names:
convert_fcr2val() => fcr_get_rxtrig_bytes()
convert_val2rxtrig() => bytes_to_fcr_rxtrig()
- Fix typo in serial8250_do_set_termios()
- Delete the verbose error message pr_info() in bytes_to_fcr_rxtrig()
- Rename *rx_int_trig/rx_trig* to *rxtrig* for several functions or variables
(but UI remains rx_int_trig)
- Change the meaningless variable name 'val' to 'bytes' following functions:
fcr_get_rxtrig_bytes(), bytes_to_fcr_rxtrig(), do_set_rxtrig(),
do_serial8250_set_rxtrig(), and serial8250_set_attr_rxtrig()
- Use up->fcr in order to get rxtrig_bytes instead of rx_trig_raw in
fcr_get_rxtrig_bytes()
- Use conf_type->rxtrig_bytes[0] instead of switch statement for support check
in register_dev_spec_attr_grp()
- Delete the checking whether a user changed FCR or not when minimum buffer
is needed in serial8250_do_set_termios()
Changes in V5.1:
- Fix FCR_RX_TRIG_MAX_STATE definition
Changes in V5:
- Support Tegra, 16650V2, 16654, and 16750
- Store default FCR value to up->fcr when the port is first created
- Add rx_trig_byte[] in uart_config[] for each device and use rx_trig_byte[]
in convert_fcr2val() and convert_val2rxtrig()
Changes in V4:
- Introduce fifo_bug flag in uart_8250_port structure
This is enabled only when parity is enabled and UART_BUG_PARITY is enabled
for up->bugs. If this flag is enabled, user cannot set RX trigger.
- Return -EOPNOTSUPP when it does not support device at convert_fcr2val() and
at convert_val2rxtrig()
- Set the nearest lower RX trigger when users input a meaningless value at
convert_val2rxtrig()
- Check whether p->fcr is existing at serial8250_clear_and_reinit_fifos()
- Set fcr = up->fcr in the begging of serial8250_do_set_termios()
Changes in V3:
- Change I/F from ioctl(2) to sysfs(rx_int_trig)
Changed in V2:
- Use _IOW for TIOCSFIFORTRIG definition
- Pass the interrupt trigger value itself
Signed-off-by: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It helps to cast struct uart_port to struct uart_8250_port at runtime.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First try to find the named clock variants then fall back to the already
existing handling of a nameless declared baudclk.
This also adds the missing documentation for this already existing variant.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The flags member has upf_t type and corresponding macros to define them. This
patch converts ASYNC_SKIP_TEST to UPF_SKIP_TEST in 8250_dw.c.
Otherwise we got a sparse warning:
drivers/tty/serial/8250/8250_dw.c:302:46: warning: restricted upf_t degrades to integer
drivers/tty/serial/8250/8250_dw.c:302:62: warning: restricted upf_t degrades to integer
drivers/tty/serial/8250/8250_dw.c:302:26: warning: incorrect type in assignment (different base types)
drivers/tty/serial/8250/8250_dw.c:302:26: expected restricted upf_t [usertype] flags
drivers/tty/serial/8250/8250_dw.c:302:26: got unsigned int
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This replaces the Baytrail specific custom set_termios hook
with a more generic one where the clock framework is used to
set the rate. The method also doesn't need to be limited to
just Baytrail, so it's used with all ACPI platforms.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the conversion to generic early console, the passing of options from
the early 8250 console to the regular ttyS console was broken. This
resulted in the baud rate changing when switching consoles during boot.
This feature allows specifying a single console option on the kernel
command line rather than both an early console and regular serial tty
console. It would be nice to generalize this feature. However, it only
works if the correct baud rate can be probed early which is not the
case on many platforms which have non-standard UART clock rates. So for
now, this is left as an 8250 specific feature.
Reported-and-tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If IGNBRK is set without either BRKINT or PARMRK set, some uart
drivers send a 0x00 byte for BREAK without the TTYBREAK flag to the
line discipline, when it should send either nothing or the TTYBREAK flag
set. This happens because the read_status_mask masks out the BI
condition, which uart_insert_char() then interprets as a normal 0x00 byte.
SUS v3 is clear regarding the meaning of IGNBRK; Section 11.2.2, General
Terminal Interface - Input Modes, states:
"If IGNBRK is set, a break condition detected on input shall be ignored;
that is, not put on the input queue and therefore not read by any
process."
Fix read_status_mask to include the BI bit if IGNBRK is set; the
lsr status retains the BI bit if a BREAK is recv'd, which is
subsequently ignored in uart_insert_char() when masked with the
ignore_status_mask.
Affected drivers:
8250 - all
serial_txx9
mfd
amba-pl010
amba-pl011
atmel_serial
bfin_uart
dz
ip22zilog
max310x
mxs-auart
netx-serial
pnx8xxx_uart
pxa
sb1250-duart
sccnxp
serial_ks8695
sirfsoc_uart
st-asc
vr41xx_siu
zs
sunzilog
fsl_lpuart
sunsab
ucc_uart
bcm63xx_uart
sunsu
efm32-uart
pmac_zilog
mpsc
msm_serial
m32r_sio
Unaffected drivers:
omap-serial
rp2
sa1100
imx
icom
Annotated for fixes:
altera_uart
mcf
Drivers without break detection:
21285
xilinx-uartps
altera_jtaguart
apbuart
arc-uart
clps711x
max3100
uartlite
msm_serial_hs
nwpserial
lantiq
vt8500_serial
Unknown:
samsung
mpc52xx_uart
bfin_sport_uart
cpm_uart/core
Fixes: Bugzilla #71651, '8250_core.c incorrectly handles IGNBRK flag'
Reported-by: Ivan <athlon_@mail.ru>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big tty / serial driver pull request for 3.16-rc1.
A variety of different serial driver fixes and updates and additions,
nothing huge, and no real major core tty changes at all.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlONXgoACgkQMUfUDdst+ymdSwCgwL0xmWjFYr/UbJ4LslOZ29Q4
BFQAoKyYe9LsfEyodBPabxJjKUtj1htz
=ZGSN
-----END PGP SIGNATURE-----
Merge tag 'tty-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty into next
Pull tty/serial driver updates from Greg KH:
"Here is the big tty / serial driver pull request for 3.16-rc1.
A variety of different serial driver fixes and updates and additions,
nothing huge, and no real major core tty changes at all.
All have been in linux-next for a while"
* tag 'tty-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (84 commits)
Revert "serial: imx: remove the DMA wait queue"
serial: kgdb_nmi: Improve console integration with KDB I/O
serial: kgdb_nmi: Switch from tasklets to real timers
serial: kgdb_nmi: Use container_of() to locate private data
serial: cpm_uart: No LF conversion in put_poll_char()
serial: sirf: Fix compilation failure
console: Remove superfluous readonly check
console: Use explicit pointer type for vc_uni_pagedir* fields
vgacon: Fix & cleanup refcounting
ARM: tty: Move HVC DCC assembly to arch/arm
tty/hvc/hvc_console: Fix wakeup of HVC thread on hvc_kick()
drivers/tty/n_hdlc.c: replace kmalloc/memset by kzalloc
vt: emulate 8- and 24-bit colour codes.
printk/of_serial: fix serial console cessation part way through boot.
serial: 8250_dma: check the result of TX buffer mapping
serial: uart: add hw flow control support configuration
tty/serial: at91: add interrupts for modem control lines
tty/serial: at91: use mctrl_gpio helpers
tty/serial: Add GPIOLIB helpers for controlling modem lines
ARM: at91: gpio: implement get_direction
...
Using dma_mapping_error() to make sure the mapping did not
fail.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 uart driver currently supports only software assisted hw flow
control. The software assisted hw flow control maintains a hw_stopped
flag in the tty structure to stop and start transmission and use modem
status interrupt for the event to drive the handshake signals. This is
not needed if hw has flow control capabilities. This patch adds a
DT attribute for enabling hw flow control for a uart port. Also skip
stop and start if this flag is present in flag field of the port
structure.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
CC: Rob Herring <robh+dt@kernel.org>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Kumar Gala <galak@codeaurora.org>
CC: Randy Dunlap <rdunlap@infradead.org>
CC: Jiri Slaby <jslaby@suse.cz>
CC: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This Multi-IO card has one serial 16550-like and one parallel port connector.
Here's the lspci output, after this commit is applied:
03:07.0 Serial controller: Device 4348:5053 (rev 10) (prog-if 02 [16550])
Subsystem: Device 4348:5053
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at cf00 [size=8]
Region 1: I/O ports at ce00 [size=8]
Kernel driver in use: parport_serial
Kernel modules: 8250_pci, parport_serial
This commit adds an entry with the device ID to the blacklist declared in
8250_pci to prevent the driver from taking ownership. Also, and as was done
for the 2S/1P variant, add a quirk to skip autodetection and set the correct
type to 16550A clone.
Proper entries are added to parport_serial, to support the device parallel
and serial ports.
Cc: Gianluca Anzolin <gianluca@sottospazio.it>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d2fd6810a8 (tty/serial: convert 8250 to generic earlycon)
removed setup_early_serial8250_console, but there are still 2 callers
in:
arch/mips/mti-malta/malta-init.c
drivers/firmware/pcdp.c
Add back the function implemented as a wrapper to setup_earlycon.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sleep function was updated to put the serial port to sleep only when necessary.
This appears to resolve the errant behavior of the driver as described in
Kernel Bug 61961 – "My Exar Corp. XR17C/D152 Dual PCI UART modem does not
work with 3.8.0".
Signed-off-by: Michael Welling <mwelling@ieee.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the generic earlycon infrastructure in place, convert the 8250
early console to use it.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to support FIX_EARLYCON_MEM on other arches, make the
option per arch.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In (efe2f29 kgdboc,kdb: Allow kdb to work on a non open console port)
support was added to directly use the "write_char" functions when
doing kdb over a non-open console port. This is great, but it ends up
bypassing the normal code in uart_console_write() that adds a carriage
return before any newlines.
There appears to have been a trend to add this support directly in
some console driver's poll_put_char() functions. This had a few side
effects, including:
- In this case we were doing LFCR, not CRLF. This was fixed in
uart_console_write() back in (d358788 [SERIAL] kernel console should
send CRLF not LFCR)
- Not all serial drivers had the LFCR code in their poll_put_char()
functions. In my case I was running serial/samsung.c which lacked
it.
I've moved the handling to uart_poll_put_char() to fix the above
problems. Now when I use kdb (and don't point console= to the same
UART) I no longer get:
[0]kdb>
[0]kdb>
[0]kdb>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the same manner as 8250_pci, 8250_dw needs some
baytrail specific quirks to be used. The reference
clock needs to be adjusted before divided in order
to have the minimum error rate on the baudrate.
The specific byt set termios function is stored in
the driver_data field of the acpi device id via the
dw8250_acpi_desc structure.
Remove the uartclk field which is no longer delivered
as driver data.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__dma_tx_complete is not protected against concurrent
call of serial8250_tx_dma. it can lead to circular tail
index corruption or parallel call of serial_tx_dma on the
same data portion.
This patch fixes this issue by holding the port lock.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On transmit-hold-register empty, serial8250_tx_chars
should be called only if we don't use DMA.
DMA has its own tx cycle.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In -RT the spin_lock_irqsave() does not spin but sleep if the lock is
taken. Before that, local_irq_save() is invoked which disables
interrupts even on -RT. Therefore local_irq_save() + spin_lock() does not
work.
In the ->sysrq and oops_in_progress case it is save to trylock the lock
i.e. this is what we do now anyway except for ->sysrq where we assume
that the lock is already taken.
The spin_lock_irqsave() grabs the lock and disables the interrupts on
vanilla (the same behavior) and on -RT it won't disable interrupts.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bigeasy: add a patch description]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support the following additional baud rates with 0% error:
500000, 1500000, 2500000, 3500000
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds