Includes one MAINTAINERS update to avoid people getting a lot of bounce
messages and complaining about it.
* MAINTAINERS
- Drop Stefan Popa's Analog Devices email address in favour of
Michael Hennerich.
* core
- Fix handling of dB sysfs inputs.
- Drop a stray semi colon in macro definition.
* ad5770r
- Fix an off by one in chec on maximum number of channels.
* ad7192
- Fix a null pointer de-reference due to the name previously being
retrieved from the spi_get_device_id call which no longer works as
the relevant table was removed.
* ad7797
- Use correct attribute group.
* counter/104-quad-8
- Add locks to prevent some race conditions.
* inv-mpu6050
- Fix issues around suspend / resume clashing with runtime PM.
* stm32-adc
- Fix sleep in invalid context
- Fix id relative path error in device tree binding doc.
* st_lsm6dsx
- Fix a read alignment issue on an untagged FIFO.
- Handle odr for slave to properly compute the FIFO data layout / pattern.
- Flush the HW FIFO before resettting the device to avoid a race on
interrupt line 1.
* st_sensors
- Rely on ODR mask not ODR address to identify if the ODR can be set.
Some devices have an ODR address of 0.
* ti-ads8344
- Byte ordering was wrong - fix it.
* xilinx-xadc
- Fix inverted logic in powering down the second ADC.
- Fix clearing interrupt when enabling the trigger.
- Fix configuration of sequencer when in simultaneous sampling mode.
- Limit initial sampling rate as done for runtime configured ones.
-----BEGIN PGP SIGNATURE-----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=SmJy
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 5.7 cycle.
Includes one MAINTAINERS update to avoid people getting a lot of bounce
messages and complaining about it.
* MAINTAINERS
- Drop Stefan Popa's Analog Devices email address in favour of
Michael Hennerich.
* core
- Fix handling of dB sysfs inputs.
- Drop a stray semi colon in macro definition.
* ad5770r
- Fix an off by one in chec on maximum number of channels.
* ad7192
- Fix a null pointer de-reference due to the name previously being
retrieved from the spi_get_device_id call which no longer works as
the relevant table was removed.
* ad7797
- Use correct attribute group.
* counter/104-quad-8
- Add locks to prevent some race conditions.
* inv-mpu6050
- Fix issues around suspend / resume clashing with runtime PM.
* stm32-adc
- Fix sleep in invalid context
- Fix id relative path error in device tree binding doc.
* st_lsm6dsx
- Fix a read alignment issue on an untagged FIFO.
- Handle odr for slave to properly compute the FIFO data layout / pattern.
- Flush the HW FIFO before resettting the device to avoid a race on
interrupt line 1.
* st_sensors
- Rely on ODR mask not ODR address to identify if the ODR can be set.
Some devices have an ODR address of 0.
* ti-ads8344
- Byte ordering was wrong - fix it.
* xilinx-xadc
- Fix inverted logic in powering down the second ADC.
- Fix clearing interrupt when enabling the trigger.
- Fix configuration of sequencer when in simultaneous sampling mode.
- Limit initial sampling rate as done for runtime configured ones.
* tag 'iio-fixes-for-5.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
MAINTAINERS: remove Stefan Popa's email
iio: adc: ad7192: fix null pointer de-reference crash during probe
iio: core: remove extra semi-colon from devm_iio_device_register() macro
iio: adc: ti-ads8344: properly byte swap value
iio: imu: inv_mpu6050: fix suspend/resume with runtime power
iio: st_sensors: rely on odr mask to know if odr can be set
iio: xilinx-xadc: Make sure not exceed maximum samplerate
iio: xilinx-xadc: Fix sequencer configuration for aux channels in simultaneous mode
iio: xilinx-xadc: Fix clearing interrupt when enabling trigger
iio: xilinx-xadc: Fix ADC-B powerdown
iio: dac: ad5770r: fix off-by-one check on maximum number of channels
iio: imu: st_lsm6dsx: flush hw FIFO before resetting the device
iio: core: Fix handling of 'dB'
dt-bindings: iio: adc: stm32-adc: fix id relative path
counter: 104-quad-8: Add lock guards - generic interface
iio: imu: st_lsm6dsx: specify slave odr in slv_odr
iio: imu: st_lsm6dsx: fix read misalignment on untagged FIFO
iio: adc: stm32-adc: fix sleep in atomic context
iio:ad7797: Use correct attribute_group
When the 'spi_device_id' table was removed, it omitted to cleanup/fix the
assignment:
'indio_dev->name = spi_get_device_id(spi)->name;'
After that patch 'spi_get_device_id(spi)' returns NULL, so this crashes
during probe with null de-ref.
This change fixes this by introducing an ad7192_chip_info struct, and
defines all part-names [that should be assigned to indio_dev->name] in a
'ad7192_chip_info_tbl' table.
With this change, the old 'st->devid' is also moved to be a
'chip_info->chip_id'. And the old 'ID_AD719X' macros have been renamed to
'CHIPID_AD719X'. Tld identifiers have been re-purposed to be enum/index
values in the new 'ad7192_chip_info_tbl'.
This should fix the bug, and maintain the ABI for the 'indio_dev->name'
field.
Fixes: 66614ab2be ("staging: iio: adc: ad7192: removed spi_device_id")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The first received byte is the MSB, followed by the LSB so the value needs
to be byte swapped.
Also, the ADC actually has a delay of one clock on the SPI bus. Read three
bytes to get the last bit.
Fixes: 8dd2d7c0fe ("iio: adc: Add driver for the TI ADS8344 A/DC chips")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Suspend/resume were not working correctly with pm runtime.
Now suspend check if the chip is already suspended, and
resume put runtime pm in the correct state.
Issues seen prior to this were:
When entering suspend, there was an error in logs because we
were disabling vddio regulator although it was already disabled.
And when resuming, the chip was pull back to full power but the
pm_runtime state was not updated. So it was believing it was
still suspended.
Fixes: 4599cac846 ("iio: imu: inv_mpu6050: use runtime pm with autosuspend")
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Indeed, relying on addr being not 0 cannot work because some device have
their register to set odr at address 0. As a matter of fact, if the odr
can be set, then there is a mask.
Sensors with ODR register at address 0 are: lsm303dlh, lsm303dlhc, lsm303dlm
Fixes: 7d24517267 ("iio: common: st_sensors: check odr address value in st_sensors_set_odr()")
Signed-off-by: Lary Gibaud <yarl-baudig@mailoo.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The XADC supports a samplerate of up to 1MSPS. Unfortunately the hardware
does not have a FIFO, which means it generates an interrupt for each
conversion sequence. At one 1MSPS this creates an interrupt storm that
causes the system to soft-lock.
For this reason the driver limits the maximum samplerate to 150kSPS.
Currently this check is only done when setting a new samplerate. But it is
also possible that the initial samplerate configured in the FPGA bitstream
exceeds the limit.
In this case when starting to capture data without first changing the
samplerate the system can overload.
To prevent this check the currently configured samplerate in the probe
function and reduce it to the maximum if necessary.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The XADC has two internal ADCs. Depending on the mode it is operating in
either one or both of them are used. The device manual calls this
continuous (one ADC) and simultaneous (both ADCs) mode.
The meaning of the sequencing register for the aux channels changes
depending on the mode.
In continuous mode each bit corresponds to one of the 16 aux channels. And
the single ADC will convert them one by one in order.
In simultaneous mode the aux channels are split into two groups the first 8
channels are assigned to the first ADC and the other 8 channels to the
second ADC. The upper 8 bits of the sequencing register are unused and the
lower 8 bits control both ADCs. This means a bit needs to be set if either
the corresponding channel from the first group or the second group (or
both) are set.
Currently the driver does not have the special handling required for
simultaneous mode. Add it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When enabling the trigger and unmasking the end-of-sequence (EOS) interrupt
the EOS interrupt should be cleared from the status register. Otherwise it
is possible that it was still set from a previous capture. If that is the
case the interrupt would fire immediately even though no conversion has
been done yet and stale data is being read from the device.
The old code only clears the interrupt if the interrupt was previously
unmasked. Which does not make much sense since the interrupt is always
masked at this point and in addition masking the interrupt does not clear
the interrupt from the status register. So the clearing needs to be done
unconditionally.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The check for shutting down the second ADC is inverted. This causes it to
be powered down when it should be enabled. As a result channels that are
supposed to be handled by the second ADC return invalid conversion results.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently there is an off-by-one check on the number of channels that
will cause an arry overrun in array st->output_mode when calling the
function d5770r_store_output_range. Fix this by using >= rather than >
to check for maximum number of channels.
Addresses-Coverity: ("Out-of-bounds access")
Fixes: cbbb819837 ("iio: dac: ad5770r: Add AD5770R support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
flush hw FIFO before device reset in order to avoid possible races
on interrupt line 1. If the first interrupt line is asserted during
hw reset the device will work in I3C-only mode (if it is supported)
Fixes: 801a6e0af0 ("iio: imu: st_lsm6dsx: add support to LSM6DSO")
Fixes: 43901008fd ("iio: imu: st_lsm6dsx: add support to LSM6DSR")
Reported-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Vitor Soares <vitor.soares@synopsys.com>
Tested-by: Vitor Soares <vitor.soares@synopsys.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fixes the call to iio_str_to_fixpoint when using 'dB' sufix.
Before this the scale_db was not used when parsing the string written to
the attribute and it failed with invalid value.
Fixes: b852822474 ("iio: core: Handle 'dB' suffix in core")
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* cros-usbpd-notify and cros_ec_typec
- Add a new notification driver that handles and dispatches USB PD
related events to other drivers.
- Add a Type C connector class driver for cros_ec
* CrOS EC
- Introduce a new cros_ec_cmd_xfer_status helper
* Sensors/iio:
- A series from Gwendal that adds Cros EC sensor hub FIFO support
* Wilco EC
- Fix a build warning.
- Platform data shouldn't include kernel.h
* Misc
- i2c api conversion complete, with i2c_new_client_device instead of
i2c_new_device in chromeos_laptop.
- Replace zero-length array with flexible-array member in cros_ec_chardev
and wilco_ec
- Update new structure for SPI transfer delays in cros_ec_spi
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXo1lfQAKCRBzbaomhzOw
wo6TAQCKHOcrqq5Y9HYXs1QBx8e/0vVwe5Jh76Qi6hUVqXu56QEA65lBZ2ni8Udp
f6jQDFkaeYaF2tkghvuNoAkFRI6/rAk=
=j4Tt
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
cros-usbpd-notify and cros_ec_typec:
- Add a new notification driver that handles and dispatches USB PD
related events to other drivers.
- Add a Type C connector class driver for cros_ec
CrOS EC:
- Introduce a new cros_ec_cmd_xfer_status helper
Sensors/iio:
- A series from Gwendal that adds Cros EC sensor hub FIFO support
Wilco EC:
- Fix a build warning.
- Platform data shouldn't include kernel.h
Misc:
- i2c api conversion complete, with i2c_new_client_device instead of
i2c_new_device in chromeos_laptop.
- Replace zero-length array with flexible-array member in
cros_ec_chardev and wilco_ec
- Update new structure for SPI transfer delays in cros_ec_spi
* tag 'tag-chrome-platform-for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux: (34 commits)
platform/chrome: cros_ec_spi: Wait for USECS, not NSECS
iio: cros_ec: Use Hertz as unit for sampling frequency
iio: cros_ec: Report hwfifo_watermark_max
iio: cros_ec: Expose hwfifo_timeout
iio: cros_ec: Remove pm function
iio: cros_ec: Register to cros_ec_sensorhub when EC supports FIFO
iio: expose iio_device_set_clock
iio: cros_ec: Move function description to .c file
platform/chrome: cros_ec_sensorhub: Add median filter
platform/chrome: cros_ec_sensorhub: Add code to spread timestmap
platform/chrome: cros_ec_sensorhub: Add FIFO support
platform/chrome: cros_ec_sensorhub: Add the number of sensors in sensorhub
platform/chrome: chromeos_laptop: make I2C API conversion complete
platform/chrome: wilco_ec: event: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_chardev: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_typec: Update port info from EC
platform/chrome: Add Type C connector class driver
platform/chrome: cros_usbpd_notify: Pull PD_HOST_EVENT status
platform/chrome: cros_usbpd_notify: Amend ACPI driver to plat
platform/chrome: cros_usbpd_notify: Add driver data struct
...
- Add support for IQS620A/621/622/624/625 Azoteq IQS62X Sensors
- New Device Support
- Add support for ADC, IRQ, Regulator, RTC and WDT to Ricoh RN5T618 PMIC
- Add support for Comet Lake to Intel LPSS
- New Functionality
- Add support for Charger Detection to Spreadtrum SC27xx PMICs
- Add support for Interrupt Polarity to Dialog Semi DA9062/61 PMIC
- Add ACPI enumeration support to Diolan DLN2 USB Adaptor
- Fix-ups
- Device Tree; iqs62x, rn5t618, cros_ec_dev, stm32-lptimer, rohm,bd71837, rohm,bd71847
- I2C registration; rn5t618
- Kconfig; MFD_CPCAP, AB8500_CORE, MFD_WM8994, MFD_WM97xx, MFD_STPMIC1
- Use flexible-array members; omap-usb-tll, qcom-pm8xxx
- Remove unnecessary casts; omap-usb-host, omap-usb-tll
- Power (suspend/resume/poweroff) enhancements; rk808
- Improve error/sanity checking; dln2
- Use snprintf(); aat2870-core
- Bug Fixes
- Fix PCI IDs; intel-lpss-pci
-----BEGIN PGP SIGNATURE-----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=hJ2o
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull mfd updates from Lee Jones:
"New Drivers:
- Add support for IQS620A/621/622/624/625 Azoteq IQS62X Sensors
New Device Support:
- Add support for ADC, IRQ, Regulator, RTC and WDT to Ricoh RN5T618 PMIC
- Add support for Comet Lake to Intel LPSS
New Functionality:
- Add support for Charger Detection to Spreadtrum SC27xx PMICs
- Add support for Interrupt Polarity to Dialog Semi DA9062/61 PMIC
- Add ACPI enumeration support to Diolan DLN2 USB Adaptor
Fix-ups:
- Device Tree; iqs62x, rn5t618, cros_ec_dev, stm32-lptimer, rohm,bd71837, rohm,bd71847
- I2C registration; rn5t618
- Kconfig; MFD_CPCAP, AB8500_CORE, MFD_WM8994, MFD_WM97xx, MFD_STPMIC1
- Use flexible-array members; omap-usb-tll, qcom-pm8xxx
- Remove unnecessary casts; omap-usb-host, omap-usb-tll
- Power (suspend/resume/poweroff) enhancements; rk808
- Improve error/sanity checking; dln2
- Use snprintf(); aat2870-core
Bug Fixes:
- Fix PCI IDs in intel-lpss-pci"
* tag 'mfd-next-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (33 commits)
mfd: intel-lpss: Fix Intel Elkhart Lake LPSS I2C input clock
mfd: aat2870: Use scnprintf() for avoiding potential buffer overflow
mfd: dln2: Allow to be enumerated via ACPI
mfd: da9062: Add support for interrupt polarity defined in device tree
dt-bindings: bd718x7: Yamlify and add BD71850
mfd: dln2: Fix sanity checking for endpoints
mfd: intel-lpss: Add Intel Comet Lake PCH-V PCI IDs
mfd: sc27xx: Add USB charger type detection support
dt-bindings: mfd: Document STM32 low power timer bindings
mfd: rk808: Convert RK805 to shutdown/suspend hooks
mfd: rk808: Reduce shutdown duplication
mfd: rk808: Stop using syscore ops
mfd: rk808: Ensure suspend/resume hooks always work
mfd: rk808: Always use poweroff when requested
mfd: omap: Remove useless cast for driver.name
mfd: Kconfig: Fix some misspelling of the word functionality
mfd: pm8xxx: Replace zero-length array with flexible-array member
mfd: omap-usb-tll: Replace zero-length array with flexible-array member
mfd: cpcap: Fix compile if MFD_CORE is not selected
mfd: cros_ec: Check DT node for usbpd-notify add
...
To be compliant with other sensors, set and get sensor sampling
frequency in Hz, not mHz.
Fixes: ae7b02ad2f ("iio: common: cros_ec_sensors: Expose cros_ec_sensors frequency range via iio sysfs")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Report the maximum amount of sample the EC can hold.
This is not tunable, but can be useful for application to find out the
maximum amount of time it can sleep when hwfifo_timeout is set to a
large number.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Expose EC minimal interrupt period through buffer/hwfifo_timeout:
- Maximal timeout is limited to 65s.
- When timeout for all sensors is set to 0, EC will not send events,
even if the sensor sampling rate is greater than 0.
Rename frequency to sampling_frequency to match IIO ABI.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Since cros_ec_sensorhub is shutting down the FIFO when the device
suspends, no need to slow down the EC sampling period rate.
It was necesseary to do that before command CMD_FIFO_INT_ENABLE was
introduced, but now all supported chromebooks have it.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
When EC supports FIFO, each IIO device registers a callback, to put
samples in the buffer when they arrives from the FIFO.
When no FIFO, the user space app needs to call trigger_new, or better
register a high precision timer.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Some IIO devices may want to override the default (realtime) to another
clock source by default.
It can beneficial when timestamps coming from the hardware or underlying
drivers are already in that format.
It can always be overridden by attribute current_timestamp_clock.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
To prevent comment rot, move function description to
cros_ec_sensors_core.c.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Introduce slv_odr in ext_info data structure in order to distinguish
between sensor hub trigger (accel sensor) odr and i2c slave odr and
properly compute samples in FIFO pattern
Fixes: e485e2a2cf ("iio: imu: st_lsm6dsx: enable sensor-hub support for lsm6dsm")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
st_lsm6dsx suffers of a read misalignment on untagged FIFO when
all 3 supported sensors (accel, gyro and ext device) are running
at different ODRs (the use-case is reported in the LSM6DSM Application
Note at pag 100).
Fix the issue taking into account decimation factor reading the FIFO
pattern.
Fixes: e485e2a2cf ("iio: imu: st_lsm6dsx: enable sensor-hub support for lsm6dsm")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This commit fixes the following error:
"BUG: sleeping function called from invalid context at kernel/irq/chip.c"
In DMA mode suppress the trigger irq handler, and make the buffer
transfers directly in DMA callback, instead.
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It should use ad7797_attribute_group in ad7797_info,
according to commit ("iio:ad7793: Add support for the ad7796 and ad7797").
Scale is fixed for the ad7796 and not programmable, hence
should not have the scale_available attribute.
Fixes: fd1a8b9128 ("iio:ad7793: Add support for the ad7796 and ad7797")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Both chips have an A/D converter capable of measuring
things like VBAT, VUSB and analog inputs.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds support for the Azoteq IQS624 and IQS625 angular position
sensors, capable of reporting the angle of a rotating shaft down to 1 and
10 degrees of accuracy, respectively.
This patch also introduces a home for linear and angular position sensors.
Unlike resolvers, they are typically contactless and use the Hall effect.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds support for the Azoteq IQS621 and IQS622 ambient light
sensors, both of which can report a four-bit representation of ambient
light intensity.
The IQS621 can additionally report illuminace directly in units of lux,
while the IQS622 can report a four-bit representation of infrared light
intensity. Furthermore, the IQS622 can report a unitless measurement of
a target's proximity to the device.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds support for the Azoteq IQS620AT temperature sensor,
capable of reporting its absolute die temperature.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
* adxl372
- Fix marking of buffered values as big endian.
* ak8974
- Fix wrong handling of negative values when read from sysfs.
* at91-sama5d2
- Fix differential mode by ensuring configuration set correctly.
* ping
- Use the write sensor type for of_ping_match table.
* sps30
- Kconfig build dependency fix.
* st-sensors
- Fix a wrong identification of which part the SMO8840 ACPI ID indicates.
* stm32-dsfdm
- Fix a sleep in atomic issue by not using a trigger when it makes no sense.
* stm32-timer
- Make sure master mode is disabled when stopping.
* vcnl400
- Update some sampling periods based on new docs.
-----BEGIN PGP SIGNATURE-----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=uJ0W
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes in the 5.6 cycle.
* adxl372
- Fix marking of buffered values as big endian.
* ak8974
- Fix wrong handling of negative values when read from sysfs.
* at91-sama5d2
- Fix differential mode by ensuring configuration set correctly.
* ping
- Use the write sensor type for of_ping_match table.
* sps30
- Kconfig build dependency fix.
* st-sensors
- Fix a wrong identification of which part the SMO8840 ACPI ID indicates.
* stm32-dsfdm
- Fix a sleep in atomic issue by not using a trigger when it makes no sense.
* stm32-timer
- Make sure master mode is disabled when stopping.
* vcnl400
- Update some sampling periods based on new docs.
* tag 'iio-fixes-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: ping: set pa_laser_ping_cfg in of_ping_match
iio: chemical: sps30: fix missing triggered buffer dependency
iio: st_sensors: remap SMO8840 to LIS2DH12
iio: light: vcnl4000: update sampling periods for vcnl4040
iio: light: vcnl4000: update sampling periods for vcnl4200
iio: accel: adxl372: Set iio_chan BE
iio: magnetometer: ak8974: Fix negative raw values in sysfs
iio: trigger: stm32-timer: disable master mode when stopping
iio: adc: stm32-dfsdm: fix sleep in atomic context
iio: adc: at91-sama5d2_adc: fix differential channels in triggered mode
While adding a new device, I noticed these aren't sorted alphabetically [as
in the Makefile], which messed my head-up.
This change sorts the devices alphabetically in the drivers/iio/dac/Kconfig
file as well.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_{predisable,postenable} functions attach/detach
the poll functions.
For the predisable hook, the disable code should occur before detaching
the poll func, and for the postenable hook, the poll func should be
attached before the enable code.
This change moves the postenable/predisable hooks into the correct
positions.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_{predisable,postenable} functions attach/detach
the poll functions.
For the predisable hook, the disable code should occur before detaching
the poll func, and for the postenable hook, the poll func should be
attached before the enable code.
The lmp9100 was attaching a poll function but never detaching it via any
IIO disable hook.
This change adds the detaching of the poll function, and moves/renames
lmp91000_buffer_preenable() function to lmp91000_buffer_postenable().
The idea is to make it more symmetrical, so that when the
iio_triggered_buffer_{predisable,postenable} functions get removed, it's
easier to see.
Fixes: 67e17300dc ("iio: potentiostat: add LMP91000 support")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add suspend/resume PM sleep ops to stm32-timer-trigger driver.
Register contents may be lost depending on low power modes.
When going to low power, enforce the timer isn't active. Gracefully
restore its state upon resume in case it's been left enabled prior to
suspend.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
"clk_enabled" flag reflects enabled state of the timer, for master mode,
slave mode or trigger (with sampling_frequency). So rename it to "enabled".
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds a TODO file with some work items added with reference to
the conversation in [1].
A TODO file is immensely useful while onboarding new contributors who
are looking for some low hanging fruit to get their foot into the door.
Since these items affect all drivers the file has been placed in the
root iio directory instead of augmenting the staging TODO.
Thanks,
Rohit
[1]: https://marc.info/?l=linux-iio&m=158256721009892&w=2
Signed-off-by: Rohit Sarkar <rohitsarkar5398@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ACCES 104-QUAD-8 series does active filtering on the quadrature
input signals via the PC/104 bus clock (OSC 14.318 MHz). This patch
exposes the filter clock prescaler available on each channel.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
InvenSense ICP-101xx sensors are a family of barometric pressure
and temperature sensor.
These devices are I2C only and use a specific protocol of
commands/responses. Data transfer is secured by using crc8.
Driver provides processed pressure and raw temperature data.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently iio_debugfs_read_reg calls debugfs_reg_access
every time it is ran. Reading the same hardware register
multiple times during the same reading of a debugfs file
can cause unintended effects.
For example for each: cat iio:device0/direct_reg_access
the file_operations.read function will be called at least
twice. First will return the full length of the string in
bytes and the second will return 0.
This patch makes iio_debugfs_read_reg to call debugfs_reg_access
only when the user's buffer position (*ppos) is 0. (meaning
it is the beginning of a new reading of the debugfs file).
Fixes: e553f182d5 ("staging: iio: core: Introduce debugfs support, add support for direct register access")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Don't confuse user with meaningless warning about the failure in getting
regulators in case of deferred probe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change adds support for the HMC1119 Silicon Digial Attenuator. The
HMC1119 is a broadband, highly accurate, 7-bit digital attenuator,
operating from 0.1 GHz to 6.0 GHz with 31.5 dB attenuation control range
in 0.25 dB steps.
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/hmc1119.pdf
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The chip is configured in 24 bit mode. The values read from
it must always be treated as is. This fixes the issue by
replacing the previous 16 bits value by a 24 bits buffer.
This changes affects the value output by previous version of
the driver, since the least significant byte was missing.
The upper half of 16 bit values previously output are now
the upper half of a 24 bit value.
Fixes: e01e7eaf37 ("iio: light: introduce si1133")
Reported-by: Simon Goyette <simon.goyette@gmail.com>
Co-authored-by: Guillaume Champagne <champagne.guillaume.c@gmail.com>
Signed-off-by: Maxime Roussin-Bélanger <maxime.roussinbelanger@gmail.com>
Signed-off-by: Guillaume Champagne <champagne.guillaume.c@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Greg Kroah-Hartman