In the hip06 and hip07 SoCs, phy connect to mdio bus.The mdio
module is probed with module_init, and, as such,
is not guaranteed to probe before the HNS driver. So we need
to support deferred probe.
We check for probe deferral in the mac init, so we not init DSAF
when there is no mdio, and free all resource, to later learn that
we need to defer the probe.
Signed-off-by: lipeng <lipeng321@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the hip06 and hip07 SoCs, the interrupt lines from the
DSAF controllers are connected to mbigen hw module.
The mbigen module is probed with module_init, and, as such,
is not guaranteed to probe before the HNS driver. So we need
to support deferred probe.
Signed-off-by: lipeng <lipeng321@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
nfp: optimize XDP TX and small fixes
This series optimizes the nfp XDP TX performance a little bit.
I run quick tests on an Intel(R) Xeon(R) CPU E5-2630 v4 @ 2.20GHz.
Single core/queue performance for both touch and drop and touch and
forward is above 20Mpps @64B packets, drop being 2Mpps faster.
I think this is max for a single queue on the low power NFPs.
There are also a few minor fixes included for code in net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For legacy reasons NFP FW may be compiled to DMA packets to a constant
offset into the buffer and use the space before it for metadata. This
ensures that packets data always start at a certain offset regardless of
the amount of preceding metadata.
If rx offset is set to 0 there may still be up to 64 bytes of metadata
but metadata will start at the beginning of the buffer, instead of:
data_start_offset = rx_offset - meta_len
Even though we make the buffers larger to accommodate up to 64 bytes of
metadata, if there is only N bytes of metadata, we will end up with
N bytes of headroom and 64 - N bytes of tailroom. Therefore we can't
rely on that space for XDP headroom. Make sure we always allocate
full 256 bytes. This, unfortunately, means we can't fit the headroom
on an u8 any more.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now the required Service Process ABI version is still tied
to max ID of known commands. For new NSP commands we are adding
we are checking if NSP version is recent enough on command-by-command
basis. The driver doesn't have to force the device to have the
very latest flash, anything newer than 0.8 should do.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading TX queue indexes from the device memory on each interrupt
is expensive. It's doubly expensive with XDP running since we have
two TX rings to check there. If the software indexes indicate that
the TX queue is completely empty, however, we don't need to look at
the device completion index at all.
The queuing CPU is doing a wmb() before kicking the device TX so
we should be safe to assume on the CPU handling the completions will
never see old value of the software copy of the index.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the RX path we follow the "drop if allocation of replacement
buffer fails" rule. With XDP we extended that to the TX action,
so if XDP prog returned TX but allocation of replacement RX buffer
failed, we will drop the packet.
To improve our XDP TX performance extend the idea of rings being
always full to XDP TX rings. Pre-fill the XDP TX rings with RX
buffers, and when XDP prog returns TX action swap the RX buffer
with the next buffer from the TX ring.
XDP TX complete will no longer free the buffers but let them
sit on the TX ring and wait for swap with RX buffer, instead.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon allocate RX buffers for caching on XDP TX rings.
The rx_ring parameter passed to nfp_net_rx_alloc_one() is not
actually used, remove it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Or points out in commit 423b3aecf2 ("net/mlx4: Change ENOTSUPP
to EOPNOTSUPP"), ENOTSUPP is NFS specific error. Replace it with
EOPNOTSUPP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid hashing the tx napi struct into napi_hash[], which is used for
busy polling receive queues.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialise init_net.count to 1 for its pointer from init_nsproxy lest
someone tries to do a get_net() and a put_net() in a process in which
current->ns_proxy->net_ns points to the initial network namespace.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creating a geneve link with 'udpcsum' set results in a creation of link
for which UDP checksum will NOT be computed on outbound packets, as can
be seen below.
11: gen0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
link/ether c2:85:27:b6:b4:15 brd ff:ff:ff:ff:ff:ff promiscuity 0
geneve id 200 remote 192.168.13.1 dstport 6081 noudpcsum
Similarly, creating a link with 'noudpcsum' set results in a creation
of link for which UDP checksum will be computed on outbound packets.
Fixes: 9b4437a5b8 ("geneve: Unify LWT and netdev handling.")
Signed-off-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Acked-by: Lance Richardson <lrichard@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc says:
====================
vxlan: do not error out on disabled IPv6
This patchset fixes a bug with metadata based tunnels when booted with
ipv6.disable=1.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The message "Cannot bind port X, err=Y" creates only confusion. In metadata
based mode, failure of IPv6 socket creation is okay if IPv6 is disabled and
no error message should be printed. But when IPv6 tunnel was requested, such
failure is fatal. The vxlan_socket_create does not know when the error is
harmless and when it's not.
Instead of passing such information down to vxlan_socket_create, remove the
message completely. It's not useful. We propagate the error code up to the
user space and the port number comes from the user space. There's nothing in
the message that the process creating vxlan interface does not know.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IPv6 is compiled but disabled at runtime, __vxlan_sock_add returns
-EAFNOSUPPORT. For metadata based tunnels, this causes failure of the whole
operation of bringing up the tunnel.
Ignore failure of IPv6 socket creation for metadata based tunnels caused by
IPv6 not being available.
Fixes: b1be00a6c3 ("vxlan: support both IPv4 and IPv6 sockets in a single vxlan device")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace pattern
int status;
...
status = func(...);
return status;
by
return func(...);
No functional change intented.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse bnx2x_null_format_ver() in functions where it's appropriated
instead of open coded variant.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use scnprintf() when printing version instead of custom open coded variants.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEE4bay/IylYqM/npjQHv7KIOw4HPYFAlkBofATHG1rbEBwZW5n
dXRyb25peC5kZQAKCRAe/sog7Dgc9qY7CACnNQLrwm8fIV72DD9+pZ1QsNwvLHCr
8ZiHSd7m/VI/FESje4Uc3D9vKi7K6MGX9/lWi70QY+2IPrTfRTrYEO5I4U3+1czc
zQ/NnQGsKBoAJdPLoXp0LkQVAXRSXUoKiaiU0VdktaAzGewixz9YxGHAcCqcu6oM
1+MftSR0iCP4mkcOyVMcnipcI9L8TzEOz2f3XB/RtMiRGcEsUekAHfdpH6NSHbAq
mG5pOwENqNn4i1ZwGg16u3p+U4YfWAF9Y+/wuev6Ob4Kla2tYnuZNEAqf9ZubY93
NBsT3pGjcbzbbihlKvu64NUlGiloQ8AGAYvttinrfx1tnsDgvP2m6nQP
=mHEY
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.12-20170427' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2017-04-25
this is a pull request of 1 patch for net-next/master.
This patch by Oliver Hartkopp fixes the build of the broad cast manager
with CONFIG_PROC_FS disabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The description inside uapi/linux/bpf.h about bpf_get_socket_uid
helper function is no longer valid. It returns overflowuid rather
than 0 when failed.
Signed-off-by: Chenbo Feng <fengc@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
avoid direct access to sk->sk_state when tcp_poll() is called on a socket
using active TCP fastopen with deferred connect. Use local variable
'state', which stores the result of sk_state_load(), like it was done in
commit 00fd38d938 ("tcp: ensure proper barriers in lockless contexts").
Fixes: 19f6d3f3c8 ("net/tcp-fastopen: Add new API support")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing a fix [1] in ___pskb_trim(), addressing the WARN_ON_ONCE()
in skb_try_coalesce() reported by Andrey, I found that we had an skb
with skb->sk set but no skb->destructor.
This invalidated heuristic found in commit 158f323b98 ("net: adjust
skb->truesize in pskb_expand_head()") and in cited patch.
Considering the BUG_ON(skb->sk) we have in skb_orphan(), we should
restrain the temporary setting to a minimal section.
[1] https://patchwork.ozlabs.org/patch/755570/
net: adjust skb->truesize in ___pskb_trim()
Fixes: 8f917bba00 ("bpf: pass sk to helper functions")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 83a77e9ec4, the phydev irq is explicitly set to PHY_POLL when
there is no pdata. It doesn't work on DT enabled platforms because the
phydev irq is already set by libphy before.
Fixes: 83a77e9ec4 ("net: macb: Added PCI wrapper for Platform Driver.")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-04-30
This series contains updates to i40e and i40evf only.
Jake provides majority of the changes in this series, starting with the
renaming of a flag to avoid confusion. Then renamed a variable to a
more meaningful name to clarify what is actually being done and to
reduce confusion. Amortizes the wait time when initializing or disabling
lots of VFs by using i40e_reset_all_vfs() and
i40e_vsi_stop_rings_no_wait(). Cleaned up a unnecessary delay since
pci_disable_sriov() already has its own delay, so need to add a additional
delay when removing VFs. Avoid using the same name flags for both
vsi->state and pf->state, to make code review easier and assist future
work to use the correct state field when checking bits. Use
DECLARE_BITMAP() to ensure that we always allocate enough space for flags.
Replace hw_disabled_flags with the new _AUTO_DISABLED flags, which are
more readable because we are not setting an *_ENABLED flag to
disable the feature.
Alex corrects a oversight where we were not reprogramming the ports
after a reset, which was causing us to lose all of the receive tunnel
offloads.
Arnd Bergmann moves the declaration of a local variable to avoid a
warning seen on architectures with larger pages about an unused variable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2017-04-30
This series contains updates to e1000e only.
Jarod Wilson fixes an issue where the workaround for 82574 & 82583
is needed for i218 as well, so set the appropriate flags.
Sasha adds support for the upcoming new i219 devices for the client
platform (CannonLake), which includes the support for 38.4MHz frequency
to support PTP on CannonLake.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the ECDH key generation takes a different path, it needs to be
tested as well. For this generate the public debug key from the private
debug key and compare both.
This also moves the seeding of the private key into the SMP calling code
to allow for easier re-use of the ECDH key generation helper.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When generating new ECDH keys with kpp, the shared secret input needs to
be set to NULL. Fix this by including kpp_request_set_input call.
Fixes: 58771c1c ("Bluetooth: convert smp and selftest to crypto kpp
API")
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
struct esw_mc_addr is a small struct that can be part of struct
mlx5_eswitch. Define it as a field and not as a pointer and save the
kzalloc call and then error flow handling.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We will activate the HW LRO only on servers with PCI BW > MAX LINK BW,
or when PCI BW > 16Gbps. On other cases we do not want LRO by default as
LRO sessions might get timeout and add redundant software overhead.
Tested:
ethtool -k <ifs-name> | grep large-receive-offload
On systems with and without the limitations.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
CQE ownership indication is as small as a single bit.
Use u8 to speedup the comparison.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
"prefetchw()" prefetches the cacheline for write. Use it for
skb->data, as soon we'll be copying the packet header there.
Performance:
Single-stream packet-rate tested with pktgen.
Packets are dropped in tc level to zoom into driver data-path.
Larger gain is expected for smaller packets, as less time
is spent on handling SKB fragments, making the path shorter
and the improvement more significant.
---------------------------------------------
packet size | before | after | gain |
64B | 4,113,306 | 4,778,720 | 16% |
1024B | 3,633,819 | 3,950,593 | 8.7% |
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
UMR operations are more frequent and important.
Check them first, and add a compiler branch predictor hint.
According to current design, ICOSQ CQ can contain at most one
pending CQE per napi. Poll function is optimized accordingly.
Performance:
Single-stream packet-rate tested with pktgen.
Packets are dropped in tc level to zoom into driver data-path.
Larger gain is expected for larger packet sizes, as BW is higher
and UMR posts are more frequent.
---------------------------------------------
packet size | before | after | gain |
64B | 4,092,370 | 4,113,306 | 0.5% |
1024B | 3,421,435 | 3,633,819 | 6.2% |
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The user can change delay_first_probe_time parameter through sysctl.
Listen to NETEVENT_DELAY_PROBE_TIME_UPDATE notifications and update the
intervals for updating the neighbours 'used' value periodic task and
for flow HW counters query periodic task.
Both of the intervals will be update only in case the new delay prob
time value is lower the current interval.
Since the driver saves only one min interval value and not per device,
the users will be able to set lower interval value for updating
neighbour 'used' value periodic task but they won't be able to schedule
a higher interval for this periodic task.
The used interval for scheduling neighbour 'used' value periodic task is
the minimal delay prob time parameter ever seen by the driver.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When IP tunnel encapsulation rules are offloaded, the kernel can't see
the traffic of the offloaded flow. The neighbour for the IP tunnel
destination of the offloaded flow can mistakenly become STALE and
deleted by the kernel since its 'used' value wasn't changed.
To make sure that a neighbour which is used by the HW won't become
STALE, we proactively update the neighbour 'used' value every
DELAY_PROBE_TIME period, when packets were matched and counted by the HW
for one of the tunnel encap flows related to this neighbour.
The periodic task that updates the used neighbours is scheduled when a
tunnel encap rule is successfully offloaded into HW and keeps re-scheduling
itself as long as the representor's neighbours list isn't empty.
Add, remove, lookup and status change operations done over the
representor's neighbours list or the neighbour hash entry encaps list
are all serialized by RTNL lock.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to offload TC encap rules, the driver does a lookup for the IP
tunnel neighbour according to the output device and the destination IP
given by the user.
To keep tracking after the validity state of such neighbours, we keep
the neighbours information (pair of device pointer and destination IP)
in a hash table maintained at the relevant egress representor and
register to get NETEVENT_NEIGH_UPDATE events. When getting neighbour update
netevent, we search for a match among the cached neighbours entries used for
encapsulation.
In case the neighbour isn't valid, we can't offload the flow into the
HW. We cache the flow (requested matching and actions) in the driver and
offload the rule later, when the neighbour is resolved and becomes
valid.
When a flow is only cached in the driver and not offloaded into HW
yet, we use EAGAIN return value to mark it internally, the TC ndo still
returns success.
Listen to kernel neighbour update netevents to trace relevant neighbours
validity state:
1. If a neighbour becomes valid, offload the related rules to HW.
2. If the neighbour becomes invalid, remove the related rules from HW.
3. If the neighbour mac address was changed, update the encap header.
Remove all the offloaded rules using the old encap header from the HW
and insert new rules to HW with updated encap header.
Access to the neighbors hash table is protected by RTNL lock of its
caller or by the table's spinlock.
Details of the locking/synchronization among the different actions
applied on the neighbour table:
Add/remove operations - protected by RTNL lock of its caller (all TC
commands are protected by RTNL lock). Add and remove operations are
initiated only when the user inserts/removes a TC rule into/from the driver.
Lookup/remove operations - since the lookup operation is done from
netevent notifier block, RTNL lock can't be used (atomic context).
Use the table's spin lock to protect lookups from TC user removal operation.
bh is used since netevent can be called from a softirq context.
Lookup/add operations - The hash table access functions are taking
care of the protection between lookup and add operations.
When adding/removing encap headers and rules to/from the HW, RTNL lock
is used. It can happen when:
1. The user inserts/removes a TC rule into/from the driver (TC commands
are protected by RTNL lock of it's caller).
2. The driver gets neighbour notification event, which reports about
neighbour validity status change. Before adding/removing encap headers
and rules to/from the HW, RTNL lock is taken.
A neighbour hash table entry should be freed when its encap list is empty.
Since The neighbour update netevent notification schedules a neighbour
update work that uses the neighbour hash entry, it can't be freed
unconditionally when the encap list becomes empty during TC delete rule flow.
Use reference count to protect from freeing neighbour hash table entry
while it's still in use.
When the user asks to unregister a netdvice used by one of the neigbours,
neighbour removal notification is received. Then we take a reference on the
neighbour and don't free it until the relevant encap entries (and flows) are
marked as invalid (not offloaded) and removed from HW.
As long as the encap entry is still valid (checked under RTNL lock) we
can safely access the neighbour device saved on mlx5e_neigh struct.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add hash table to the representors which is to be used by the next patch
to save neighbours information in the driver.
In order to offload IP tunnel encapsulation rules, the driver must find
the tunnel dst neighbour according to the output device and the
destination address given by the user. The next patch will cache the
neighbors information in the driver to allow support in neigh update
flow for tunnel encap rules.
The neighbour entries are also saved in a list so we easily iterate over
them when querying statistics in order to provide 'used' feedback to the
kernel neighbour NUD core.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The nud_state and hardware address fields are protected by the neighbour
lock, we should acquire it before accessing those parameters.
Use this lock to avoid inconsistency between the neighbour validity state
and it's hardware address.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Instead of relaying on the 'flow->rule' pointer value which can be
valid or invalid (in case the FW returns an error while trying to offload
the rule), monitor the rule state using a flag.
In downstream patch which adds support to IP tunneling neigh update
flow, a TC rule could be cached in the driver and not offloaded into the
HW. In this case, the flow handle pointer stays NULL.
Check the offloaded flag to properly deal with rules which are currently
not offloaded when querying rule statistics.
This patch doesn't add any new functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Passing output device parameter to the helper functions that deal with
creation of encapsulation headers is redundant. Output device parameter
can be defined inside those helpers, no need to pass it. Refactor the code by
removing the parameter from the function signature.
This patch doesn't change any functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The encap entry structure isn't manipulated by the eswitch code,
hence it can/needs to be removed from the eswitch header.
Do that, and change it to have mlx5e_ prefix.
This patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Encap wise, the tc eswitch flow attribute struct needs to have
only the encap ID which is programmed later to the HW and none
of the higher level encap params, fix that.
This patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Make representor netdev private data extendable by adding new struct
"mlx5e_rep_priv" and use it as the rep netdev private data struct
instead of directly pointing to mlx5_eswitch_rep.
Added new en_rep.h header file to contain all representor related
definitions and prototypes, and moved all representor specific logic
into en_rep.c.
Needed for downstream patches to extend representor functionality to
support neighbour update.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Add support for 38.4MHz frequency is required for PTP
on CannonLake. SYSTIM frequency adjustment attributes for TIMINCA are
get/set dependent on the hardware clock frequency for a different
types of adapters. 38.4MHz frequency supported by CannonLake
and active once time synchronisation mechanism was enabled
Changed abbreviation from Hz to HZ to be compliant checkpatch code style
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The propagation of CannonLake mac type to driver functionality
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i219 (6) and i219 (7) are the next LOM generations that will be
available on the nextIntel Client platform (CannonLake)
This patch provides the initial support for these devices
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I've got reports that the Intel I-218V NIC in Intel NUC5i5RYH systems used
as a PTP slave experiences random ~10 hour clock jumps, which are resolved
if the same workaround for the 82574 and 82583 is employed, so set the
appropriate flag2 in e1000_pch_lpt_info too.
Reported-by: Rupesh Patel <rupatel@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On architectures with larger pages, we get a warning about an unused variable:
drivers/net/ethernet/intel/i40evf/i40evf_main.c: In function 'i40evf_configure_rx':
drivers/net/ethernet/intel/i40evf/i40evf_main.c:690:21: error: unused variable 'netdev' [-Werror=unused-variable]
This moves the declaration into the #ifdef to avoid the warning.
Fixes: dab86afdbb ("i40e/i40evf: Change the way we limit the maximum frame size for Rx")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This matches the ordering of how we free stuff during reset and remove.
It also makes logical sense because we set the interrupts based on the
number of queues. Currently this doesn't really matter in practice.
However a future patch moves the assignment of num_active_queues into
i40evf_alloc_queues, which is required by
i40evf_set_interrupt_capability.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The flag used by the common code and PF code is I40E_FLAG_FD_ATR_ENABLED,
not *FDIR*. It turns out none of the txrx code actually shared with the
VF driver actually checks the ATR flag. This is made even more obvious
by the typo in the VF header file.
Let's just remove the flag from the VF driver since it's not needed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hw_disabled_flags field was added as a way of signifying that
a feature was automatically or temporarily disabled. However, we
actually only use this for FDir features. Replace its use with new
_AUTO_DISABLED flags instead. This is more readable, because you aren't
setting an *_ENABLED flag to *disable* the feature.
Additionally, clean up a few areas where we used these bits. First, we
don't really need to set the auto-disable flag for ATR if we're fully
disabling the feature via ethtool.
Second, we should always clear the auto-disable bits in case they somehow
got set when the feature was disabled. However, avoid displaying
a message that we've re-enabled the feature.
Third, we shouldn't be re-enabling ATR in the SB ntuple add flow,
because it might have been disabled due to space constraints. Instead,
we should just wait for the fdir_check_and_reenable to be called by the
watchdog.
Overall, this change allows us to simplify some code by removing an
extra field we didn't need, and the result should make it more clear as
to what we're actually doing with these flags.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
lipeng